Search Documents

By M I. Pownceby, W J. Bruckard

A South African chromite sample was subjected to characterisation and physical beneficiation testwork in order to assess its suitability to produce an upgraded chromite product with a silica level of <1 per cent SiO2 and a chromite level of >46 per cent Cr2O3. Chemical analysis by XRF indicated that the bulk material had a Cr2O3 content of 40.5 per cent w/w and a SiO2 content of 7.5 per cent w/w. Combined XRF analysis with sizing data showed that the majority (~70 per cent) of the siliceous material was present in the +600 ¦m fraction while ~70 per cent of the Cr2O3 was in the -600 ¦m fraction. Qualitative mineral phase analysis by XRD indicated that the sample mineralogy was dominated by ferrian-magnesiochromite spinel ([Fe,Mg]Cr2O4) and aluminium-chromite spinel (Fe[Al,Cr]2O4), with enstatite (Mg2Si2O6), haematite (Fe2O3) and anorthite (CaAl2Si2O8) as minor phases. SEM and EMP characterisation showed that the silica was mainly present in discrete enstatite grains but lesser amounts were also present as the high silica phases plagioclase and enstatite on the edge of grains. Wet gravity separation performed on sized fractions (-600+106 ¦m size range) from the -2.0 mm (primary) ore as well as the ore that had been crushed to pass 0.6 mm (secondary) showed that stage crushing of the -2 mm +600 ¦m fraction followed by wet gravity separation upgraded the Cr2O3 grade at 70 per cent Cr2O3 recovery from ~44 per cent Cr2O3 in the primary material to 46 per cent Cr2O3 (the target grade specification) in the secondary sample. It also showed that the stage crushing of this +600 ¦m fraction at a cut-off level of one per cent SiO2 increased the cumulative Cr2O3 recovery from ~50 per cent in the primary material to ~63 per cent in the secondary sample in the same size range of -600+106 ¦m. The extent to which additional crushing could lead to improved chromite recoveries at the required chromite and silica grade target specifications was not determined. This experience demonstrates that prior to processing test work being conducted, a thorough understanding of the chemistry and mineralogy of the test sample promotes efficient and targeted processing research.

Jan 1, 2008

By Burman B. C

This paper describes studies into two particular aspects of the Lochiel deposit which formed part of feasibility level geot2chnical and hydrogeological investigations for proposed open cut mine development. The two aspects were depressurisation of thick beds of silt located through the profile and the determination of characteristics and origins of soil structure and their effect on pit stability. The studies were very detailed and multi disciplinary and highlight the integration of geology, geotechnics, hydrogeology and mining that is required for mine development studies. It is considered that as more marginal deposits are developed throughout the world the demands for efficient economic mining together with in- creasing scales of operation will require simi- lar types of studies. As such the studies pre- sented herein are likely to be a forerunner to a,emerging trend for development of open pit mines in difficult ground and water conditions.

Jan 1, 1986

The distribution of p(~rphyt1 copper deposits, in time as well as place, is used to propose an occurrence model based on the genesis models of Sillitoe and Rona. A magmatic source of the metals is accepted. The characteristic metallogenic epoch and the migration of the mineralization event along an elongate metal province are explained as the result of subduction of an obliquely- oriented strip of mineral-enriched material on the oceanic plate. Two mineral-enriched trails emanate from a hot-spot source of high-intensity hydrothermal activity in an oceanic rift. Because the whole plate system moves relative to hot spots, the hydrothermal source appears to migrate along the rift, and the two trails are not parallel to transform faults, but form a broad "V" centred on the hotspot. Source loci are spaced at intervals of about 3000 km, resulting in the possible repetition of metallogenic epochs, in a subduction zone province, at about 100 m.y. intervals. The position of the mineral-enriched strip can be found graphically, given ages of a series of deposits in a province, and the plate convergence vectors. This knowledge provides an exploration tool at regional scale and, by reflection across the rift, the potential for exploration is extended across oceans. The model has implications for commodities and deposit types other than porphyry coppers.

Jan 1, 1987

By Jaracz K

At the operation of mine winders in deep shafts considerable oscillations of winding ropes may occur due to elasticity of both wind-ing and balance ropes. The amplitudes of longitudinal oscillations may reach + lm at relatively low frequencies, ranging from 0.5 to 2 c/s. These oscillations may be dangereus for the rope and produce several hazards to the winding installation as a whole. They may cause conside-rable instant accelerations on the pulley and dangerous tensions in ro-pe wires. The excessive acceleration may cause the uncontrolled rope slip on the pulley. Several methods of limitation of these accelera-tions were developed, some of them have been already in control system: of electric drive of the winder. The most simple ones are: a/ limita-tion of the rate of change of acceleration and retardation of the win-der /so called "jerk"/ and b/ the proper selection of regulators of the winder control system to get the optimal control. The trouble in solv-ing the problem of rope oscillations is that the dynamic system of the winder is a nonstationaryone owing to changing distance of conveyance from the pulley. Besides, the system is described by the equations with distributed parameters. The brief discussion of the theory and its practical aspects are enclosed as well.

Jan 1, 1985

By Schofield N. A

The cross-sectional method of stope grade estimation at Cobar Mines has consistently had several shoneomings, me most imponant of which being mat stope grade is significantly overestimated in the high grade lenses.The use of mree-dimensional ore lens modelling improved the grade estimation and ore waste definition but significant overestimation still occurred in me high grade stopes, particularly those wim extremely variable grade distribution. The implementation of an indicalor kriging based method for mapping of me high grade copper mineralization has significantly improved the quality of copper grade estimates and provides a mineralisation geometry similar to that generated manually by me mine geologists. This paper presents the results of a test case study in the application of indicator kriging to the mapping of the copper grade in two stopes in the QTS North mineralisation. The results are encouraging in that they prov ide coofi rmation of the geometrical model developed by the geologists and much improved estimates of the grades of me stopes whencompared to me grade reponed from mining these stopes.

Jan 1, 1993

Epithermal gold mineralisation was discovered at the Muyup prospect during regional reconnaissance exploration in 1986. Further exploration utilising routine techniques of stream sediment, panconcentrate, rockchip sampling and geological mapping resulted in the discovery of five auriferous vein systems located along northwest-trending fault zones. Scout diamond drilling was conducted on two of the vein systems. Mineralisation is hosted by a poorly exposed, mid-Tertiary volcanic inlier composed of intermediate and minor felsic volcanic rocks intruded by intermediate hypabyssal por- phyries. Gold is wholly contained in narrow steep-dipping hydrothermal breccias and quartz vein stockworks in which chalcedonic silica and fine grained quartz is the predominant gangue with minor adularia, carbonate, and sulphides. Alteration zoning is manifested as intense fracture-controlled silicification mantled by narrow clay-rich envelopes which in tam grade outward and downward into propylitic alteration or unaltered host rocks. Late advanced argillic alteration is superimposed on the vein-related altera- tion assemblages. Alteration assemblages and fluid inclusion data suggest that gold mineralisation occurred in response to episodic hydraulic fractur- ing and boiling of low to moderate temperature, dilute alkali-chloride fluids. The Muyup prospect represents the shallow eroded remnants of an epither- mal gold deposit enriched in Au, Ag, As, Sb and Hg. Low sulphur fugacities reflected by vein and alteration assemblages support an adularia-sericite classification (Heald et al, 1987) for this epithennal gold deposit.

Jan 1, 1991

By S Pigram, G J. Jameson

This paper is concerned with the tracking of particles in the froth phase of an aerated water/glycerol mixture. Experiments have been carried out in a specially designed laboratory flotation cell that allows formation of a deep froth. Phosphorescent tracer particles of various sizes were injected into the centre of a froth column where they were excited by ultraviolet lights, positioned at the back and front of the column. The motion of particles was captured on a digital camera with a green filter. The images from the digital camera were then transferred to a computer and an image analysis program was used to convert the colour intensity to the concentration of particles at each location within the froth. The tracer technique was used to determine the dispersion of hydrophilic particles and the variation of the concentration of solids with axial and radial positions.

Jan 1, 2005

By J Zanganeh, M Ajrash, B Moghtaderi

Application of thermal oxidation is considered a promising technique in reducing fugitive methane gas from ventilation air methane (VAM). A typical thermal oxidiser operates with diluted methane and converts it to less potent greenhouse gases. However, having a thermal oxidiser in the vicinity of the coalmine exhaust shaft is a major safety concern as its high operation temperature increases the likelihood of accidental fire and explosion. The aim of this study is to investigate the application and effectiveness of side venting technique in reduction of deflagration consequences caused by methane gas. To address this importance a series of experiments were conducted on a detonation tube designed and fabricated as part of larger scale VAM Abatement safety project. The experimental work was carried out into two stages: examine the flame and explosion properties in a large-scale detonation tube to get reliable data; and then design and employ a venting system into the detonation tube to verify the effectiveness and performance of the venting against the flame and explosion.Results corresponding to this study show that the side vent duct with venting coefficient magnitude of 37 had a significant influence on methane flame deflagration and the explosion characteristics. The maximum pressure rise at the detonation tube reduced approximately 20 per cent to 32 per cent by applying the side venting duct. Also, the data shows that the venting damped the pressure oscillation after the flame deflagration which eventually reduced the system instability. Finally, by applying the venting technique the expected level of damage due to the dynamic pressure reduced to the level of limited building damage.CITATION:Ajrash, M, Zanganeh, J and Moghtaderi, B, 2017. Application of side venting technique in mitigation of methane – air explosion and flame deflagration in ventilation air methane, in Proceedings Australian Mine Vent Conference 2017, pp 153–258 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 28, 2017

By S Pollak, A Amon

This paper describes the current and finished design work which has been performed for shallow rock station caverns for New York CityÆs first new subway construction in 60 years. A new robust, sophisticated, design procedure has been developed for two up to 30 m wide caverns, with overburden of less then 12 m, and rock cover to span ratios (C/S) in the order of 0.25. The design is based on empirical input parameters like the Q-value, rock mass rating (RMR) values, rock mass class after Cording (1984), cover to span ratios, which have been validated by the use of structural computer models as well as two- and three-dimensional numerical discontinuum models. The design approach is a staged approach using first principles, empirical models and non-linear FEM and DEM models. In addition, the paper describes the factors and circumstances why shallow caverns have been selected instead of cut-and-cover structures and why all the underground station structures have been developed as drained structures.

Jan 1, 2008

Commencing early in 1975, Saraji Mine in Central Queensland will product 3.56 million tonnes in the first year and then 4.57 million tonnes annually for the Japanese and European markets. The coal will be mined from a series of pits separated by corridors which will be mined at a later date. Through the corridors flow regional drainage structures and power lines. Relatively easy areas will be mined initially to assist the cash flow and to minimise start-up difficulties. For ease of scheduling it is desirable that pit lengths exceed 3 000m but this will not always be possible. Ramps were designed using 1 200m spacing and 5 per cent gradient as optimum but modified to suit specific conditions. One ramp will be in the end of each pit nearest the ROM hopper and stripping will commence from this end. The advantages so gained are shorter haul distances, immediate access to the coal after stripping and simplification of the excavation of the first ramp. Haul road location was defined by the minimum present value of construction plus operating costs. Road design utilised airfield construction charts because wheel loads were outside the range of available road design manuals. Low load resistance characteristics of

Jan 1, 1974

Amongst the Pacific Rim countries, Papua New Guinea (PNG) is the leader in new gold discoveries and developments leading to new production. PNG has shown a dramatic increase in gold production when taken from a base of about 600 000 ounces in 1984 to 1 160 000 ounces in 1986. 1987 is expected to produce about 1 500 000 ounces and new planned developments will give further large increases. PNG's leading position when compared with neighboring Pacific Rim countries is only partly due to its favorable geological setting along the "Rim of Fire" epithermal zone. More important have been well-thought-out mining development legislation and good administration as well as consistent taxation and royalty policies. A stable political environment and a track record of new mining developments over the last 15 years, both pre and post Independence in 1975, have also been important factors in encouraging the new developments. Early Portuguese explorers associated the New Guinea mainland with gold as early as 1525 but it was not un,11 1R77 that a small ill-fated gold rush gave the first recorded production at Laloki near Port Moresby. Modest but commercial discoveries were made in the outer islands and coastal mainland regions from 1888 to 1926. In 1922 William "Sharkeye" Park found gold at Edie Creek and this led to major discoveries at Wau and Bulolo which were the first large scale commercial gold Operations.

Jan 1, 1987

By Croggon R

Passing a direct current through a jointed fine grained soft rock mass auses the movement of water by the process of electric-osmosis. There are other processes such as electrolysis which transport ions that interact with associated ions and can, in turn, be oxidised. This results in the dissolution products being transported towards the cathode electrode. In the cathode region the ferrous hydroxide is oxidised to ferric hydroxide %%ith consequent precipitation. The cracks and joints are current pathways, along which the ferric hydroxide is deposited. This deposition reinforces the joints and increases the shear strength. By adding calcium chloride to the anode, the rate of corrosion is increased with the concomitant increase of deposited ferric hydroxide along the joints. This, in turn, significantly increases the joint shear strength. The process is pervasive in that the current via the water paths travels through the crack and joint systems The result is that not only specific joints are reinforced but the cracks and mtciconnected voids are also reinforced.

Jan 1, 1997

By Still RF

Sintering of lead and zinc concentrates is practised by Sulphide Corporation Pty. Limited to provide both desuiphurised lump sinter feed, for simultaneous reduction to zinc and lead in the Imperial Smelting Process blast furnace, and sulphur dioxide gas for sulphuric acid manufacture. From November, 1969 a 20 percent increase in production rate has been obtained through improvements in operating technique. A gradual increase in bed permeability was achieved by modifications to the feed mix conditioning equipment and by improving moisture control. However advantage could not be taken of the higher permeability to increase sulphur elimination because the hardness of the lump sinter decreased. Higher throughput, better quality sinter and more stable sintering conditions were however made possible by simultaneously: 1. reducing segregation and compaction in the sinter bed, by narrowing the discharge opening of the main layer feed hopper, 2. reducing the sizing of sinter returns to give a closer size spectrum of particles in the feed mix, and 3. increasing the sulphide sulphur content of the feed mix to give higher bed Temperatures.

Jan 1, 1972

The Olympic Dam mining operation is some 520 kilometres NNW of Adelaide on the Roxby Downs Pastoral lease. The deposit containing copper, uranium, gold and silver was discovered in 1975 by Western Mining Corporation (WMC). A joint venture was formed in mid-1979 between WMC (51 per cent) and British Petroleum (BP, 49 per cent) for the development and exploitation of the deposit. WMC assumed 100 per cent ownership after acquiring BP's share in early-1993. Ore is won from a highly mechanised underground mining operation and processed to refined products. Current annual output from the mining of 3.0 Mt of ore is approximately 83 500 t of refined copper, 1400 t of uranium oxide, 750 kg of gold and 12 000 kg of silver. Conventional long hole, open stoping techniques are used to extract the production ore. Since stope production began in April 1988, full surveys and appraisals of stopes have been carried out to evaluate the integrity of the design and blasting techniques. This evaluation included the determination of the degree of dilution or non break that had occurred. Performance information also made it possible to re-design any adjacent stopes to retrieve remaining ore and conversely, avoid the chances of targeting backfilled material in the future. Performing stope surveys proved not only to be a time-consuming process but one fraught with access and line-of-sight problems. Occasionally it was not possible to obtain any stope survey data, and as was often the case with the mine pass system, rarely. In 1992 the sudden failure of the pillar between the fine ore and mullock passes and the subsequent delays to production, emphasised the need to effectively monitor pass wear. Initial information regarding the development of the Cavity Measurement System (CMS) prototype (Figure 1) indicated that it had the potential to solve these problems by the introduction of a remote scanning device into a cavity. Following a great deal of investigation, Olympic Dam Operations purchased the first CMS in Australia. This paper discusses its application for all underground void surveys and the procedures developed to manage both field and office requirements.

Jan 1, 1995

Ore reserve estimates form a basis for strategic mine planning at Argyle Diamonds open pit and alluvial operations. Most ore reserve statements are mainly concerned with resource tonnage and grade. Because diamond deposits are low grade, high value resources, diamond quality ($/carat) is also an important parameter. Relatively large variations in quality and/or grade can occur. These variations must be taken into account before the resource potential can be fully assessed. Computers (HP9000 and PC's) are utilised to compile resource inventories. Resource inventories are then ranked on an economic basis. This paper discusses the methods used to compile resource inventories and explains how these are then used to present ore reserve estimates in terms of resource potential.

Jan 1, 1990

By R Dimitrakopoulos

The development of mineral resources is based on a spatial model of the orebody that is only partly known from exploration drilling and associated geological interpretations. As a result, orebody models generated from the available information are uncertain and may require the use of stochastic conditional simulation techniques. Multiple-point methods have been developed for petroleum reservoir modelling, enabling reproduction of complex geological geometries. This paper considers a multiple-point approach to capture the uncertainty of the lithological model. The implementation of the method at the Yandi channel iron ore deposit in Western Australia and performance characteristics are discussed. The uncertain lithological model translates into considerable grade-tonnage uncertainty.

Jan 1, 2007

The Lennard Shelf is an Upper Devonian carbonate reef complex striking northwest for 350 km along the northeast margin of the Canning Basin. Numerous small Mississippi Valley type (MVT) Pb-Zn prospects occur within this belt, including the Wagon Pass prospect, located 105 km east of Derby in the Napier Range. At Wagon Pass, the base of the Upper Devonian sequence is a cobbly, dolomitic sandstone, the Van Emmerick Conglomerate. This is conformably overlain by the Frasnian to Famennian Pillara cycle Lower Napier Formation fore-reef deposits. These are characterized by red algal wackestones and terrigenous stylo- bedded packstones, with common dolomitization. The conformably overlying Famennian Nullara cycle contains a classic reefal assemblage, consisting of flat lying Nullara Limestone back-reef, fore-stepping massive Windjana Reef, and steep basinward dipping Upper Napier Formation marginal slope. The Nullara cycle is not dolomitized. The Wagon Pass mineralization is hosted by Lower Napier Formation dolomite. Mineral- ization consists of complex intergrowths and semi-massive assemblages of sphalerite and galena, with subordinate pyrite, marcasite, chalcopyrite, bornite, digenite, covellite and bravoite. Ore textures include granular and colloform. Gangue minerals are dolomite and very fine grained green chloritic clay. Although mineralization commonly occurs as reticulate fracture fillings, its overall distribution is stratabound. Ore paragenesis involved early "diagenetic" dolomitization, followed by breccia formation with chloritic and granular dolomite matrices. Main stage galena-sphalerite mineralization then occurred, accompanied by pervasive chloritization of silty units. Ore genesis was probably related to basin-derived "oil field" brines, with open space textures in the mineralization quite comparable to textures seen in Canning Basin dolomitic hydrocarbon reservoirs. Fluid inclusions in the host dolomite have typical MVT homogenization temperatures of 70-1150 C, and contain minor organic phases. The Van Emmerick Conglomerate, with its high porosity, dolomitization and weak Pb-Zn anomalism, was probably the aquifer for the mineralizing brines. Access of ore solutions to the Wagon

Jan 1, 1986

The ""multiple of exploration expenditure"" method of mineral valuation is applicable to exploration properties from the earliest stage of exploration to a moderately advanced stage but for which no resources have been delineated. While not recommended as a primary valuation method by some workers, others believe it to be the most satisfactory method of valuing exploration properties until it is possible to employ a DCF technique. In many situations facing the professional valuer, the method may represent the only semi-quantitative option available and is frequently used. Significantly it often forms the starting point in discussions to farm-in on an exploration tenement. The paper briefly reviews the definition of value as applied to mineral valuation and in particular examines the relationship between fair value and market clearing price in ""fair"", bull and bear markets. The multiple of exploration expenditure method uses previous exploration expenditure and/or future committed exploration expenditure to derive a base value for the tenements. This base value is multiplied by a prospectivity enhancement multiplier (PEM) with adjustments for market premium or discount and consideration of the quality of the exploration team to derive a fair value for the tenements. The paper will demonstrate that there is no necessary nexus between fair value derived from the method and present book Values.

Jan 1, 1994

At Yucca Mountain, USA, a tunnel is being built according to nuclear quality standards. It has proved possible to meet very high quality demands while at the same time achieving high advance rates. To be able to do this, routines on how to record and store quality related information have been established. This has meant that a new philosophy has entered the tunnelling industry. Especially for nuclear waste projects, of which Yucca Mountain is one of the first ones to be built, the experiences made and the quality assurance program established will be of great importance for future projects. The paper gives examples of what the Nuclear Quality Assurance system has meant in practice for the tunnelling at Yucca Mountain. And, it also explains why a non-grouted bolt, Super Swellex-, was chosen for long-term reinforcement in the tunnels which might host nuclear waste for thousands of years.

Jan 1, 1999

The Escondida Porphyry Copper Deposit, located in Chile's II Region 160 Km to the southeast of the city of Antofagasta, is currently owned by Minera Escondida Limitada, a company comprising The Broken Hill Proprietary (57.5%), Rio Tinto Zinc (30%) a group of Japanese companies represented by Mitsubishi Corporation (10%), and the International Financing Corporation of the World Bank (2.5%) (Fig.l)By 1983, most of the reconnaissance drilling was completed and prefeasibility studies were regularly updated as new drilling results were reported and project concepts re-evaluated (Fig.2). In October 1982 the project was transferred from Exploration Management to Operations. By the end of 1984 project pre-development activities, including inpit development drilling, geological exploration, water resource definition, an underground bulk sampling program and the initial project feasibility report, were completed.

Jan 1, 1990