Search Documents

To obtain the best economic results in treating the comparatively high-grade ore of the Kalgurli Mine a good roast is essential, and the effort of this paper will be to briefly describe the plant and the conditions prevailing in roasting, which, on an output of about 360 tons daily, subsequently enable an average extraction of slightly over 94% of the gold to be maintained.The percentage of sulphur in the ore varies between 2'5 and 3'5, the lower figure existing when treating oxidized ore. The average gold value is 13 dwt; this occurs chiefly as sylvanite, containing .a lower percentage of silver than is usually present in that mineral. One ore body in the mine contains hessite (Ag2Te) in considerable quantity, associated with gold telluride, and when ore from this stope is being treated the silver contents rise to as high as 20 dwt, but the usual amount is about 9 dwt. per ton, of which only a small proportion is extracted. Other metallic minerals, in addition to pyrite, occurring more or less commonly, are arsenopyrite, magnetite, chalcopyrite, and the tellurides calaverite (AuTez)and coloradoite HgzTe3). A small proportion only of the value occurs as free gold.

Jan 1, 1911

By Quan P. M

The great advances made in the application of solvent extraction to the recovery of copper from low grade ore sources over the past 15 to 20 years are well known. Solvent extraction is an essential step in the recovery and purification of copper from dilute sulphate leach solutions by which some one million tonnes of copper are now electrowon annually. A reagent is also available for the selective recovery of copper from chloride leach solutions and this may hold the key to the processing of complex sulphide ore concentrates. By comparison, the use of solvent extraction in the recovery and processing of zinc has as yet found little favour and is confined to only a few specific and comparatively small applications. This is despite the ready availability of a large number of low grade zinc sources and zinc-bearing wastes and residues. It is suggested that this difference is due in large part to the absence of suitable reagents having the particular features required to enable them to fit into a solvent extraction - electrowinning based process for zinc. Ideally, for the recovery of zinc from dilute sulphate solution, an extractant should operate on a proton exchange principle and be strong for zinc in the same way that o-hydroxyaryloxime reagents are strong towards copper. It should load efficiently with zinc at the pH of typical sulphate feed streams without the need for neutralisation and yet be stripped efficiently by spent zinc electrolyte. Another factor of major importance for many applications, however, is that it should be highly selective for zinc over ferric iron. These features have now been realised in a development extractant DS5846, which is a formulation of a novel class of reagent currently under investigation by Zeneca Specialties. The properties of this reagent are described with respect to selectivity, isotherms and how they compare with phosphoric and thiophosphoric acids that have been previously proposed for the extraction of zinc. For the recovery of zinc from concentrated chloride solutions a solvating or neutral donor type of extractant is required which again should ideally have high selectivity for zinc over a number of other metals, particularly iron. The new reagent Acorga ZNX50 is based on a formulation of a novel class of compound developed specifically for this purpose. It gives efficient extraction of zinc from feed solutions that are four to six molar in chloride ion but is readily stripped at 60 - 65¦C using either water, dilute brine, or spent zinc chloride electrolyte. The reagent is highly selective for zinc over iron and a range of other metals including cadmium, arsenic, lead and magnesium.

Jan 1, 1993

By Lynce AJ

A method has been developed for the prediction 'of 'the- . performance of a multi-stage grinding=cyclone classification circuit of any degree of complexity on any ore for a wide range `of operating conditions, The-.method involves ;the. s` inu ation b'f the circuit on a digital computer by means of. matheinatical' models ":bf the"' individual units:, the. development of which is- also discussed'., At present, in order to establish 'the!'" charac'teristtics of they ¦ore- and the machines. in mathematical terms;. it is necessary to know'the performance of a , simpl,.e. ; system on tri.e ore - for! one known ,,feed rate and.fe.ed s,l-zing, analysis. ' ,Fiiither work on :the- separate identification 'of the terms defining the characteristics of the ore and the machines may permit the method to be, applied directly to the cj.4ta,derived from small scale tests on ores,

Jan 1, 1964

Iron formation-hosted iron ore deposits account for the majority of current world iron ore production and consist of three classes: unenriched primary iron formation with typically 25 to 45 wt per cent Fe; martite-goethite ore formed by supergene processes, with abundant hydrous iron oxides containing 60 to 63 wt per cent Fe; and high-grade hematite ores thought to be of hypogene or metamorphic origin overprinted by subsequent supergene enrichment with 60 to 68 wt per cent Fe.Individual iron ore deposits range from a few millions of tonnes to over two billion tonnes at >64 wt per cent Fe, although most are within the range of 200 to 500 Mt. In the Hamersley Province of Western Australia, martite-goethite ores are largely developed in the Marra Mamba Iron Formation, although high (>0.08 per cent P) phosphorous mineralisation is also well developed in the stratigraphically higher Brockman Iron Formation. Whilst the vast majority of high-grade microplaty hematite ore is best developed in the Brockman Iron Formation, this paper provides the first textural evidence of locally significant microplaty hematite mineralisation in the Nammuldi Member of the Marra Mamba Iron Formation, in the Chichester Ranges at the Christmas Creek, Cloud Break and Mount Nicholas prospects. Petrographic studies have identified a high-grade Fe texture composed of nanometre scale plates of hematite in mineralised sections of primary microplaty hematite deposits in the Pilbara and elsewhere, well below the normal depth of weathering or dehydration. The population of nanometre to micrometre scale hematite plates is interpreted to represent various stages of nucleation, crystallisation and progressive growth of hematite from the primary ore-forming fluid in areas that were once iron-rich carbonates or silicates in the BIF.

Jan 1, 2005

Ridgeway Gold Mine (Ridgeway) has a clear mission to maximise its cash flows in order to deliver shareholder value and is developing strategies to achieve this. Business process management using leading measures is core to this approach. Leading measures indicate potential outcomes ahead of time, allowing time to adapt and improve. Ridgeway is making strategy a central organisational agenda, creating a focus to æput first things firstÆ by controlling æleadingÆ activities and mobilising employees to act. Feedback using specific, leading measures gives employees the opportunity to proactively adapt their behaviour in order to deliver internal business outcomes that generate cash flows and shareholder value. This paper will outline RidgewayÆs business approach to track and control processes from resource to revenue, with a focus on delivering cash flows and shareholder value. Ridgeway is implementing a Balanced Scorecard approach (Kaplan and Norton, 1996). A total business focus is taken and leading measures are identified. Specific measures are used to score our success from the perspectives of learning and growth, internal business processes, customer and stakeholders, and finance. These measures and improvement plans are targeted at strategies to maintain our ælicence to operateÆ with our community stakeholders, produce accurate plans and forecasts, improve our operational effectiveness and grow our business.

Jan 1, 2002

By Wetzeil N

High ambient temperatures combined with high surface humidity in the north of Australia and, in particular, the northern areas of the Northern Territory can make underground workplaces relatively inhospitable at certain times of the year. . Woodcutters' silver/lead/zinc mine, situated some 80 km south of Darwin, would be the most northerly underground operation of any significance in Australia. As such, during the build up to the wet season, it has a particular problem of ventilating a deep underground mine with already high dry and wet bulb temperatures at the surface. The Mine Management Act and Regulations mention only that workplaces shall be 'in a fit state for a person to work in or occupy'. Woodcutters therefore set in progress a Heat Stress Program to endeavour to set standards which would be more measurable and justifiable. The aim of the program was to compile a record of ambient atmospheric conditions in the working areas such that areas and/or work activities generating high ambient temperatures and humidities could be identified, quantified and qualified. Once the analysis stage of this program was completed, Woodcutters compiled a set of recommendations for the continued monitoring for, and control of, heat stress conditions to ensure that no underground employee was placed at risk from 'heat stress'. These recommendations are discussed in this paper.

Jan 1, 1994

By M Wortley, A Cantarutti, T Ozkocak

The estimation of the grinding mill charge weight is vital to ensure its efficient performance. Mill underloading or overloading can cause losses through decreased production or unplanned down time. Metso Minerals Process Technology Asia Pacific and South America (MMPT) has developed two systems for measuring mill load. The first is an acoustic system (SmartEarÖ) and the second is an online model-based charge estimation system. The aim of both systems is to facilitate better operation of grinding mills. SmartEarÖ performs analysis on an audio signal from the mill and allows each different frequency component to be viewed, analysed and used in process control for load estimation. By isolating different frequencies, SmartEarÖ can give an estimate of mill load. The online dynamic mill model uses measurable mill parameters (such as power) to predict the current total load. Kalman filtering can also be utilised to further increase the accuracy of the model. Both of MetsoÆs systems have been installed at BHP BillitonÆs Cannington mine to measure the load within their autogenous (AG) mill. In this paper, the methods of mill load estimation are reviewed and compared to the bearing pressure reading, which is the current method used by Cannington to control mill load. The redundant estimates of mill load provide increased confidence and consequently more robust grinding operation under a wide range of conditions.

Jan 1, 2008

By B Hall

In feasibility studies the choice of optimum cut-off grade is typically based on an evaluation of tonnage grade curves and manual design of stopes at one or two cut-off grades. In the industry these stope designs are usually based on break-even cut-off grades, but there is little consensus on what cost and price assumptions ought to be included. A new tool for automated stope design has been developed that generates sets of stope shapes for a nominated range of cut-off grades, or depending on the nature of the mineralisation, cut-off values based on net smelter return calculations in the block model. The stope design procedure includes constraints in stope and pillar geometry for the selected mining method and can be used to evaluate sublevel interval and sensitivities to other design parameters in the specific geological and geotechnical environment. These ænested stopesÆ are analogous to ænested pitsÆ in open cut design, and can be used as a key input in the æhill of valueÆ methodology for the evaluation of the optimum cut-off grade in underground design. The results of many consulting studies indicate that a break-even cut-off grade will not be the optimum cut-off grade. A particular benefit of the new stope design tool is that the design rules used to establish stope shapes in the feasibility study can then be used in mine production, in an optimal and repeatable method. This methodology is being advanced in the AMIRA P884 PRIMO project, which is a new research collaboration coordinated by AMIRA International. The project has brought together active research groups in Australia and Canada, with the goal of developing a flexible framework and set of software tools for optimisation in underground mine design.

Jan 1, 2009

ADDRESS BY THE PRESIDENT OF THE INSTITUTE (MR. J. G. SYMONS) IN PRESENTING THE CERTIFICATE TO ROBERT COLVILLE BRADSHAW, O.B.E.Today it is my privilege and pleasure to introduce to you, Robert Colville Bradshaw. O.B.E., the third New Zealander to be honoured with Honorary Membership of The Institute. Sir William Hudson and Mr. C. H. Benney were the others.Mr. Bradshaw has been an Affiliate Member of The Institute since the formation of the New Zealand Branch in 1966. Like his friend Matt Benney. Bob Bradshaw is an accountant by training. Last June he retired as senior partner of the firm of chartered accountants, now known as Wilkinson Wilberfoss, with which he served from January 1929.Mr. Bradshaw grew up in New Zealand attending the Terrace School in Wellington, the New Plymouth Boys' High School where he was a boarder, and completing a Bachelor of Commerce at the university now known as the Victoria University of Wellington. He is an elected Fellow of the New Zealand Society of Accountants and an Associate of the United Kingdom Institute of Cost and Works Accountants.

Jan 1, 1977

By R M. Hough, G Duclaux, M A. Pearce, M F. Gazley

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. Microcharacterisation, such as that described in this paper, provides understanding of a mineral system at multiple scales, and understanding microscale variations is the key to understanding the large-scale variations in a mineral system. More than 50 high-grade lode samples from across Plutonic Gold Mine (Plutonic), Marymia Inlier, Western Australia were analysed by a variety of techniques, including micro X-ray fluorescence (µXRF) mapping, micro X-ray computed tomography (µCT), scanning electron microscopy (SEM), field emission gun SEM, electron back-scatter detector (EBSD), proton-induced X-ray emission microprobe and synchrotron XRF mapping. These data demonstrate that competency contrasts are the key to governing the location of Au mineralisation at Plutonic. Micro CT imaging of high-grade samples shows the Au filling in voids and pore-space in the rock, after having travelled along more permeable layers and already existing or reaction-induced pores formed during hydrothermal circulation. Using 3D visualisation, the Au is seen to form a connected network that appears undisturbed at the scale of the samples, and a high-grade Au deposition event was one of the last events to affect the rock. This interpretation is supported by SEM analyses on high-grade samples that reveal calc-silicate (epidote-clinozoisite) alteration that is not present in lower Au grade samples, which are typically dominated by potassic alteration, and that sulfides are typically less abundant close to the Au. The replacement of biotite by chlorite is an alteration associated with the high-grade Au-mineralising fluid. Gold is coarsest where Au particles are located on the margins of minerals, typically sulfide and quartz grains, suggesting the importance of rheological contrast at the microscale. Furthermore, EBSD data reveals that Au is undeformed and overprints peak metamorphic and retrograde minerals. Data confirm recent deposit-scale observations, suggesting that deposition of high-grade, visible Au was related to a hydrothermal fluid circulation event late in the geological history of Plutonic.CITATION:Gazley, M F, Duclaux, G, Fisher, L A, Hough, R M and Pearce, M A, 2015. High-resolution characterisation of gold mineralisation at Plutonic Gold Mine, Western Australia – evidence for the late-stage deposition of high-grade gold , in Proceedings PACRIM 2015 Congress, pp 51–58 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

By Spencer GA, Saul SJ

The flight line spacing in low level aeromagnetic surveys is the principal factor governing both the cost and the amount of geological detail which can be extracted from the data. The rate at which geological resolution diminishes with wider line spacing is illustrated by progressive subsampling of a 200 m spaced data set from the Charters Towers region in Queensland.The usefulness of high frequency type filters in enhancing shallow structural features is seen to be limited to the 200 m data.It is concluded that each data set is suited to a particular scale and style of geological investigation with only the 200 m data having sufficient detail to identify the subtle structural patterns which are crucial to mineral exploration.

Jan 1, 1976

By S Kodate, Ö Aydan, Y Suda, J Tomiyama

Fracture zones are commonly found in the Earth’s crust. These zones may cause very severe engineering problems. Therefore, the formation and the assessment of the mechanical characteristics of these zones is of great concern for rock engineers. A new double shearing jig was used to study the formation of shear zones in rock under static and impact loading conditions using the device developed by the authors. A series of experiments were undertaken to investigate formation on the formation and characteristics of fracture zones in laboratory. Although actual fracture zones are more complicated, various tests give some insight view of the formation of fracture zones as well as some information on their mechanical behaviour under both dynamic conditions and static conditions. The authors report the outcomes of these experiments and discuss their implications in practice.

Nov 29, 2022

The mechanism of caving is of interest to the mining engineer only in areas where he is directly concerned. One area is surface subsidence which is outside the scope of this paper. Another area is at the face where coal is being extracted and where control of caving is of vital importance. Coal mining systems have been developed with many considerations in mind, but in this list of considerations, strata control has seldom been given much importance. Research is in progress in Australia to endeavour to determine an optimum sequence for coal extraction underground. As information becomes avail- able from this work it is hoped that appropriate methods of controlling caving in various strata conditions will be devised. When this is done, equipment may be introduced to permit the mining operation to proceed under optimum conditions for strata control, rather than devising a mining procedure to suit the equipment available and methods developed for other reasons.

Jan 1, 1974

By McConachy G. W, Wright J. V

During the 110 years since the discovery of the Broken Hill PbZnAg deposit six major mining companies have mined the ore body and explored the ore environment. Despite this activity, no new orebodies have been found at Broken Hill. The failure to discover large new resources cannot be attributed to a lack of activity because major companies have maintained substantial exploration commitments over many decades. This suggests that not only was a unique coincidence of conditions required to form the deposit but also that full recognition and definition of the critical parameters may not yet have been recognised. In an attempt to illuminate some of the more unusual and poorly studied characteristics of the ore environment some new areas of investigation are presented here which may contribute to understanding the ore deposit setting and focus exploration towards different and perhaps more productive targets. Sedimentological characteristics of the host succession of the Broken Hill deposit are apparently unique along the line of lode. An upward-coarsening megasequence reflected in the development of clastic psammites stratigraphically below the ore deposit is one important ingredient which has received little exploration focus. These psammites also host mineralisation and form part of a spectrum of quart-zrich rocks collectively referred to as gametiferous psammites, garnet quartzites and blue quartz lodes. Sedimentological data interpreted from outcrop, drill core and downhole geophysical well logs support a elastic origin for some of these rocks; an interpretation which is at variance with traditional interpretations favouring an exhalative origin. A clastic origin for many of the footwall psammites, and their close spatial association with the orebodies suggests their role in ore formation was important. It is interpreted as a critical part of the fluid flow architecture within the sedimentary basin, which focussed ore forming fluids into an unique environment favourable for trapping mineralisation. Detailed stratigraphic correlation near the deposit has also highlighted that quartzofeldspathic rocks (Potosi gneisses and lode pegmatites) have complex relationships with ore. Suites of stratabound quartzofeldspathic pegmatites have received limited study, but their distribution and voluminous development suggests they may be as important to ore formation as the psammitic lode rocks which host the orebodies. These associations are not in conflict with some recent ore forming models invoking deposition in a shallow water environments of deposition. The geochemistry of parts of the host sequence has been studied extensively in the past but this has not been merged with current stratigraphic subdivisions. A large drillhole data base now permits the geochemistry to be related to the sedimentary succession and reveals that a signature involving stratigraphic vectors best illustrated by changes in MnO, Na2O, Pb and Zn can be detected. This is interpreted to reflect sedimentary basin processes as opposed to a classical volcanic hydrothermal alteration pipe associated with seafloor venting. The stratigraphic setting together with characteristics of some of these poorly understood areas is discussed to emphasise that construction of sound models for exploration requires the total ore environment to be studied with attention directed to the geometry and setting of the full range of host rocks. Control of the greater portion of the line of lode by a single company, Pasminco Australia Limited, now permits disparate datasets and observations to be merged and presents new opportunities and encouragement for model refinement and exploration success.

Jan 1, 1993

By Campbell Brown G F

THE Mount Morgan mine has, from the time of its historical discovery, been the subject of investigation and speculation by geologists and mining engineers. The first examination was made by Dr. R. L. Jack, in 1884. He came to the conclusion, from theevidence then available, that nothing but a thermal spring in the open air-otherwise a geyser-could account for the formation of the ore body. This report attracted world-wide attention at the time. Since then the mine has been examined by most of the leading geologists of Australia, and by many from elsewhere. In all cases the examination has only extended over a period' of a few days or weeks, and in the light of present knowledge of the deposit we know that sufficient data could not be obtained in such a short time to warrant the statement of definite conclusions. It is not to be wondered at, therefore, that a considerable difference of opinion exists as to the genesis of the deposit. That the company considered more detailed investigation necessary is shown by the fact that some thirteen years ago it employed Mr. Charles Walker as geological surveyor on the .mine. At that time also the data available was insufficient to give satisfactory results. It is, however, a matter for comment that none of the geological reports on the property took notice of the increase of copper values in the ore with depth, though the present workings and diamond-drilling...

Jan 1, 1911

By B Whiteley, B Gee

The Northside Storage Tunnel is a TBM driven rock tunnel system designed to collect and store sewage from four major storm overflow points along the existing Northern Suburbs Ocean Outfall Sewer. At present, sewage overflows during wet weather are the main source of pollution for Sydney Harbour. The tunnel system comprises a 16 km long by 3.8 m to 6.5 m diameter tunnel from Lane Cove to the North Head Sewage Treatment Plant and a 4 km long by 6.3 m diameter branch tunnel from West Chatswood. The tunnel will have a typical rock cover of about 50 m to 150 m. Most of the tunnel alignment is contained within the Hawkesbury Sandstone Formation which is generally an excellent tunnelling stratum, and offers few geotechnical constraints. However, the tunnel is required to pass beneath incised palaeochannels at Middle Harbour and Manly with each palaeochannel containing about 70 m of sediment.Innovative geotechnical and geophysical investigations were undertaken to examine the tunnel route and characterise the rock beneath the palaeochannels. These investigations have located zones of poor quality rock beneath one palaeochannel in particular, suggesting significant stress relief had taken place in the rock at times of lower sealevel producing structural features indicative of valley bulging. This paper presents the geotechnical model developed for the tunnel, and the models and constraints for tunnelling beneath the palaeochannels.

Jan 1, 1999

By Paterson M. R, Spencer P. A

Vitrokele technology is a resin process that can be applied in gold plants to reduce both capital and operating costs. The Vitrokele resin can be used for both precious metal recovery and for recovering free and combined cyanide from effluent streams. Vitrokele resin has been extensively tested at pilot plant level and is now applied successfully at a commercial heap leach facility in Zimbabwe where it is used in place of activated carbon for recovery of gold from pregnant leach solution. Significant capital cost savings were achieved by installation of a resin plant instead of a conventional carbon adsorption plant. Operation to-date has not seen any significant physical or chemical degradation of the resin either in terms of adsorption capacity/kinetics or physical appearance/size. This gold recovery process is equally applicable to slurry streams where it would be implemented in stirred tanks with interstage screens in a similar manner to a conventional carbon adsorption plant.

Jan 1, 1996

As a result of high fuel prices and substantial haul distances or vertical lift from pits, the development of large inpit crushing and conveying systems at many open pit operations has occurred over the last decade.The basic criteria that has to be met is that the material is reduced in size to be conveyable. Generally this requires a top size of less than 300 mm.

Jan 1, 1992

By T Berryman

The Fimiston reserve is being depleted at the rate of one million ounces per year; most of which is processed by the Fimiston plant, with the remainder being stockpiled. As for most other large open cut mines around the world, Fimiston has an excellent dispatch and tracking system. Reconciliation is used to determine how the various models used in mine planning (such as a reserve, budget and schedule models) are tracking against production. It is also used to gauge the performance of grade control estimation against production; however, analysing the results of this can be complicated and, at times, misleading. The reconciliation process involves adjusting the monthly production data to equal the mill reported tonnes and grade, plus the change in stockpiles. This adjusted number is then compared to the grade control reported tonnes and grade, the scheduled model (monthly planning model) tonnes and grade and against budget (Reserve) tonnes and grade. This paper includes explanations of all assumptions made in the reconciliation process, including the end of month closing stocks balance, the application of adjustment factors to the dispatch data to create a new balanced set of production data and the monthly sign off to comply with the Sarbanes-Oxley requirements of the North American owners. The reserve is reconciled by proved and probable classification. This tool is used to assess the robustness of the classification scheme utilised and identify any reconciliation issues as they arise. Within the Fimiston deposit there are still issues that are clouded by the assumptions made concerning the scale of observation, poor data support and the mining of the narrow lode areas of the deposit. The declared ore mined (DOM) number (which is defined in the paper) can be significantly affected by these assumptions, and these need to be clearly stated and understood when looking at the reconciliation data. The DOM tonnes and grade is a good indicator of real mine performance as it adjusts mined tonnes and grade to take into account the milled tonnes and grade each month, and prevents cumulative errors from building up in mine predicted dispatch numbers or end of period stockpiles. This number allows monthly monitoring of the mine to mill performance and allows valid comparisons to be made back to budgets and reserves over a period of time. KCGM uses three month rolling averages to monitor performance against reserve and budget models. This ensures that monthly distortions in the figures due to stockpiling issues or over mining in a particular period do not lead to false conclusions. Reconciliation performance over a longer period (12 - 18 months) is used to adjust reserve models should significant variance be observed. By closely monitoring the reconciliation performance at the Fimiston operation, fine tuning of all aspects of the grade estimation process from reserve through to grade control can be made. This allows the most accurate data to be used when planning from reserve data for the Life of Mine Plan through to grade control data for short-term mill feed.

Jan 1, 2006

By N McKenzie, F Brodbeck

The North-South Bypass Tunnel is the first project to get underway as part of BrisbaneÆs transport plan, which aims to improve the urban road network. The total length to be excavated is 6.8 km, which includes 4.8 km of driven tunnel and associated road connections. Construction commenced in August 2006 with project completion targeted well before the contractual completion date of October 2010. Due to the local geology, in particular the hard Brisbane tuff and neranleigh-fernvale formation, a combination of tunnel excavation methods are used. The majority of the tunnel is excavated by two tunnel boring machines which have a rate of progress of 16 - 20 m per day in rock having a compressive strength of between 80 and 150 MPa. Ten roadheaders operate at a rate of up to 2 m per day excavating the remaining tunnels, such as ramps, access tunnels, cross passages and merges. The tunnel team are managing the challenges and complexities associated with tunnelling through the hard Brisbane rock. A major challenge arose during the planning of the initial mainline excavation underneath the Royal National Association Showground in Bowen Hills. This section contains low rock cover and historical maps indicate that the showground is located within a former topographic depression (alluvial valley), which a creek once flowed through.Due to traffic merge design requirements, both tunnel boring machine (TBM) and roadheader excavation methods were required to be used in this challenging geological profile. The answer was to stabilise the alluvium above both TBM section tunnels from the surface prior to excavation and to operate the TBM in single shield mode with immediate grouting of annular void from the tail shield. In addition, the roadheader section of tunnel required additional support by spiles and canopy tubes installed from the tunnel face.

Jan 1, 2008