Search Documents

By W F. Bawden, J T. Paynter

This investigation involves laboratory testing and stability analysis of paste fill at the Golden Giant Mine. Site-cast samples are tested in unconfined, confined, and consolidated-undrained triaxial compression. Pore pressures during shear and consolidation characteristics are measured to determine both drained and undrained shear strength parameters and assess the potential for undrained loading. Liquefaction potential is also considered. A limit equilibrium solution is used to obtain factors of safety against failure of the fill during mining of adjacent stopes.

Jan 1, 1998

By M P. Sandy, J B. Simpson

The empirical stope design techniques developed by Mathews et al (1981) and refined by Potvin (1988) and others, have gained rapid acceptance in Australia in the 1990s as a simple, æfirst-passÆ means of designing primary stopes. However, it is recognised that these æstability graphÆ methods can only provide broad design guidelines. Recently published stability graphs (Hutchinson and Diederichs, 1996) encompass a wide range of geological environments, which are not discussed, and the influence of time and blasting practices cannot be easily reviewed. The æscatterÆ in the graphs must reflect, to some degree, different operating practices as well as subtle but important differences in the pre-mining conditions that are not adequately accounted for in the æmodified stability numberÆ. Development of a ælocalÆ, site-specific stability graph may overcome some of these problems. At NormandyÆs Golden Grove Operations, Western Australia, detailed reviews of stope stability performance, including Cavity Monitoring System (CMS) surveys, are undertaken for every stope, with the objective of developing a series of local stability graphs, customised to site conditions and calibrated in terms of æAverage Falloff ThicknessÆ (AFT). Cablebolting of stope hangingwalls is used to develop reinforced æbeamsÆ on each sublevel, effectively dividing the full span into smaller, more stable æsubspansÆ. By analysing stope stability performance in terms of fall-off, cost-benefit studies can be undertaken of the effect of cablebolting and other options for modifying stope spans. The approach used to develop the local stability graphs, and their integration into routine stope design procedures at Golden Grove, is described. The experience gained during stope extraction in the Scuddles orebodies has been successfully applied to the Gossan Hill æC-PanelÆ orebody. This methodology should be applicable to other underground mining operations.

Jan 1, 2000

By Chen Z, Dong H

This paper describes the autogenous carrier flotation of 0 - 20 ¦m ilmenite using 40 -- 80 }tm ilmenite as carrier. Investigation is made of the influence of main technological parameters on autogenous carrier flotation. The mechanism of autogenous carrier flotation is discussed using extended DLVO theory. The main conclusions are as follows: 1. the smaller the fine particles the more easily they adhere.to carriers; 2. the selectivity of autogenous carrier flotation depends on the selectivity of adsorption of collector. In the autogenous carrier flotation of ilmenite/plagioclase mixture assaying 15.35 per cent TiO2, a concentrate containing 47.17 per cent Ti02 can be obtained by primary separation with a recovery of 93.05 per cent. KEYWORDS: Autogenous carrier flotation, extended DLVO theory, ilmenite, styrylphosphonic acid.

Jan 1, 1993

By Hegedus M

The Hydrogeological Survay of the bauxite mines in Hungary was establisned 30 years ago. The goal of the HS has been to collect the all available date needed to solve the hydrogeological problems of bauxite mines. The results of activity of the HS have been summarized in the annual reports-. This report is going to present a few methods to evaluate the hydrogeological properties of fissured, karstic rock ie. the evaluation of drilling mud losses, the statistics of core samples evaluated by a special computer program for calculation the porosity and permeability of the rocks. An experimental injection test is presented together with the development of a new portable instrument to get signes of the water table change during the injection test in every two second. It can be proved that the flow around the well may be a transient one if the yield of the injection exceeds a definite one (Figure 2.). It was observed that the permeability calculated from the pumping test date may be 1.2-1.6 time higher than it coming from the injection test. A practical example is presented also how to use the results of the HS for designing the dewatering of a new mine together with an analogous computer model to forecast the yield expectable for making the drift tunnel. A suggestion based on the hydrogeological feature has been done for the dewatering without using electric energy (see Figure 3.-6.).

Jan 1, 1988

By S Hapugoda, J Manuel, E Donskoi, L Lu

Sinter can constitute up to 80–85 per cent of the total ferrous burden in modern blast furnace ironmaking operations. The mineralogy and microstructure of iron ore sinter play an important role in determining its physical and metallurgical properties. As a result, characterisation of sinter phases is a cost-effective and complementary tool to conventional physical and metallurgical testing of iron ore sinter in evaluating and predicting sinter quality. Over the years, CSIRO has developed a scheme for characterising iron ore sinter that classifies primary sinter phases such as unreacted and partially reacted hematite and magnetite, and secondary phases, including prismatic high-temperature silico-ferrite of calcium and alumina (SFCA), microplaty SFCA (SFCA 1), dense SFCA, secondary hematite and magnetite, glass, larnite (dicalcium silicate; Ca2SiO4) and remnant fluxes. Quantification of these phases has traditionally been carried out by manual point counting under a petrographic microscope; however, new technologies based on automated optical image analysis, quantitative X-ray diffraction and scanning electron microscopy are now available for evaluation. In this study, two sinter samples of varying chemistry were prepared and characterised using both point counting and automated optical image analysis. The implication of the results obtained for the performance of different quantification methods is also assessed.CITATION:Hapugoda, S, Lu, L, Donskoi, E and Manuel, J, 2015. Mineralogical quantification of iron ore sinter, in Proceedings Iron Ore 2015, pp 35–44 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

By B Belle

"Mines around the world are inherently and operationally diverse. Current methodologies for the design of mine ventilation and cooling infrastructure involve controlling major safety and health hazards. Globally, it can be estimated that mine ventilation systems from various commoditiescirculate over 150 000 m3/s of exhaust air through shafts. Additionally, over 2 000 000 workersare transported every day through shafts in labour-intensive mining countries like China, India,Southern Africa, and the Americas. A key objective of this paper is to share experiences and provide a case for the revision of ætime-honouredÆ ventilation design parameters based on a benchmarking exercise on design exhaust shaft velocity from various global operations (gold, diamond, platinum, coal and base metals). An active fi eld observation on exhaust shaft velocity has indicated that, regardless of the commodity or continent where the mine operates, almost all life-of-mine (LOM) design parameters provided are in the same range of 20 m/s to 22 m/s, which is not convincing considering signifi cant variations exist in shaft depths, geography, commodity, operating and capital costs. From a due diligence perspective, there are no documented views that are available on the most widely used design exhaust air velocity. Based on the global exhaust shaft velocity data, it is noted that a significant portion of shaft velocities are outside the current design velocity of 20 m/s (some operating up to 30 m/s) and other signifi cant portions of the exhaust shafts operate in the critical velocity range. In the case of Australian coal mines, limited data suggests that none of the mines have ever reached the LOM design exhaust shaft velocity. It is self-evident that when the shafts are not operating at their design quantities either the mine system resistance is low or the ventilation and main fan is operating ineffi ciently. The most common reasons given for not reviewing the shaft system were, ætime-honouredÆ design parameter are being used and cannot be changed, mine fan pressure limits, possible fan blade damage, possible spontaneous combustion risks, leakage or simply did not consider such a possibility. In conclusion, the study has reiterated the historic lessons that a safe and expensive airway should not be utilised uneconomically by circulating too litt le air through it."

Jun 1, 2012

By Vink L, Johnson N. W, Mackenzie J, Young M. F, Johnston M, Landmark V

The influence of ore textures on metallurgical behaviour is poorly understood for most ores. An alternative method for characterising ore textures and for determining the resulting implications on ore processing has been developed for the Geor

Jan 1, 1998

By R Vleggaar

In addressing a short-term operational need for the relocation of a tailings storage facility reclaim pond, a mine has achieved a host of water management objectives. Through effective planning and adoption of a strategic æwhole of mine lifeÆ approach, the mine has achieved significant environmental, social and economic benefits. A review of all water management aspects across the site identified a host of other interrelated water issues and concerns which, if dealt with individually, would prove too costly for individual operational departments. When considered as a whole, however, the issues became opportunities and provided the stimulus for integration of the site water management system. The development of site water and solute balance models provided the tool by which a number of water management options/strategies could be evaluated. The conceptual design and costing of the proposed water infrastructure further facilitated the evaluation of the multiple benefits to be gained from each option. A business case could then be made to mine management for the preferred option. The recommended water management strategy finally recommended to the mine not only provided a tailings storage facility (TSF) reclaim pond, but also provided for:increased wastewater recovery from the TSF, the capture of all waste rock dump run-off, additional water harvesting from local creeks, increased wastewater reuse, improved environmental water management, infrastructure that could be used by the local community after mine closure, and overall cost savings. This paper illustrates how effective water management planning can provide both short-term economic and environmental benefits, as well as long-term social benefits.

Jan 1, 2006

Excavation through fill material in underground metalliferous mines is usually avoided where possible, unlike in Civil Engineering application where excavation through soft ground is normally a matter of course. In the mining situation, where excavation is normally for access only, then excavation designs are engineered for mining in hard rock, except where previous lack of forward planning has made such excavation inevitable or a mining strategy sequence necessitates some mining through fill in order to achieve optimum recovery of ore. Historically, this has been the case, because of the lack of knowledge of the support characteristics of the fill material placed underground and the lack of knowledge of the composition of the fill material as placed. The expertise and experience available from mechanised excavation techniques in Civil Engineering application (shield jacking, forepoling, spiling, and soft tunnel boring, to name a few) are available for application to the underground mining situation if the need ever arises. This paper describes the situations in underground mining development where mining through fill material is required, the different types of fill material encountered and the types of support available

Jan 1, 1981

The great variety of geological conditions in French coal deposits has obliged the industry to develop different thick seam mining methods. In very steep seams in a dense deposit where stowing is necessary to avoid spontaneous combustion, surface subsidence and water problems, a rising horizontal slice method is used, the coal being hard enough and the seams regular (Lorraine). In very thick and irregular steep seams where the stowing is not necessary, a sub-level horizontal slicing is used; a third method has to be used in Dauphine.

Jan 1, 1976

By J J. Laas, A J. S Spearing

Considering the capital outlay, running costs and inherent difficulties of backfilling operations at depth the benefits need to be clearly established, quantified and then exploited. Expansion of Vaal Reefs Exploration and Mining Company towards even deeper, highly faulted ground, and the process of establishing codes of practice for the management of rockfalls and rockbursts, required that a sound support strategy be formulated. This paper describes the derivation of an overall backfilling strategy on Vaal Reefs. Use was made of experience gained over some 12 years with backfilling. Numerical modelling was used to estimate potential benefits of backfilling the deepest mining areas still to be extracted. In exploiting a probably unique opportunity, two contiguous mining areas bounded by the same major geological structures, were compared. One was extensively backfilled and the other not at all. Shaft sinking through a backfilled stope added another dimension to the database.

Jan 1, 1998

By A Tolley

Bauxite residue or ‘red mud’ is a by-product of the Bayer Process, the primary process of alumina refining. Due to its high alkalinity and variable composition, its storage and disposal poses high environmental risks to water sources, surrounding ecosystems and human health. The high alkalinity (pH 12–13) is a significant factor in its classification as hazardous waste; to mitigate this, Australian refineries have integrated neutralisation processes into bauxite refining. Both sea water and carbon dioxide neutralisation processes are applicable. Multiple studies have demonstrated pH reduction from 12–13 to 7–10, depending on the method. The key advantages of CO2 neutralisation are that it allows for carbon sequestration and is more effective when utilised as a pre-treatment for recovery of metals, while sea water neutralisation is more established and has been integrated into two Australian refineries. This paper proposes the application of the bacteria Exiguobacterium oxidotolerans for bioleaching of iron from hematite in bauxite residue. The genus Exiguobacterium is characterised by its high levels of adaptability, halotolerance and alkaliphilic nature. E. oxidotolerans is successful at eluting Fe2+ from hematite via reductive dissolution, which complexes with oxalic acid produced during metabolism. This aquatic bacterium presents a novel process pathway for iron elution due to direct interaction of E. oxidotolerans with hematite via the cell membrane and operates within the pH range of neutralised red mud. The proposed mechanism is extracellular electron transfer, a microbial metabolic process where electron transfer is facilitated between bacterial cells and extracellular material. Currently this is being investigated for promotion of seaweed growth in coastal environments as soluble iron aids and fortifies colonies. This has potential downstream applications for cleaner iron and steel production. While theoretical, this paper explores the neutralisation, bioleaching and application of the Fe(II)- and Fe(III)-oxalate complexes formed.

Sep 18, 2023

The risks faced by organisations are part of a risk continuum. They can be evaluated in terms of hazard, uncertainty and opportunity as well as by the degree of influence they have on conformance, operating performance and strategic objectives. This paper discusses the application of risk management techniques for mitigating blasting hazards, reducing blasting output variability, and implementing blast improvement opportunities. Effective risk management practices can identify and evaluate risks across all levels of the continuum and can deliver realistic assessments of the likelihood and impact of risks on the companyÆs safety and business objectives. This paper does not attempt to present technical details about blasting, rather it aims to provide enough blasting context and examples so that the practical benefits of applying the risk management process to blasting can be fully appreciated. The topics discussed include: explosive management plan; statistical process control; quality blasting, rock-on-ground; Blast Management; Mine to Mill optimisation; and blasting information systems. The concept of a blasting risk management system employing a continuous improvement loop is also introduced. On reflection the insights presented should be extremely useful for observing and understanding which risk face has management focus at a mine site or for a blast site.

Jan 1, 2001

By A Campbell

Trials of different tapping operations at Olympic Dam have been carried out with the aim of improving the safety of tapping and improving the integrity and lifetime of the taphole. This has involved trialling the use of a mudgun and drill on one of the tapholes of the electric furnace in place of the normal manual tapping procedures. The blister copper tapholes are currently closed using a conical clay plug formed around a steel bar. The plug is pushed into the taphole by hand to stop the flow, and the cooling on the outer part of the taphole freezes the blister copper in the tapping channel. The hole is burnt open using consumable oxygen lances. This puts the furnace technicians in close proximity to molten metal and heat û which is reflected in the safety incidents reported by these operators. By moving to a mudgun and drill operation, the furnace technicians will be moved away from the taphole area improving their safety. Additional benefits include: improved tapping cycles; extended taphole refractory lifecycles; and improved furnace integrity around the taphole, hopefully extending the campaign. This paper outlines the trials that have shown that it is possible to plug and drill blister copper (not matte) tapholes using a mudgun and drill.

Jan 1, 2005

This paper describes the new iron and steelmaking process recently commissioned at NZ Steel. Ironsand mined and concentrated at Waikato North head is slurry pumped 18 km to the company's Glenbrook works. Ironmaking includes the direct reduction process pioneered at Glenbrook in the 1970s and a new continuous electric melter. The molten, high carbon pig iron produced is then fed to a vanadium recovery unit and on to the KOBM oxygen steelmaking vessel. Steel is cast into billets or slabs. The new plant, which is the first stage of a fully integrated works at Glenbrook, raises New Zealand Steel's production capacity from 150 000 t/y to 750 000 t/y.

Jan 1, 1986

By P J. Harris, C T. OÆConnor

Collectors are used to impart hydrophobicity on particles thus increasing their chances of reporting to the froth phase. Also, the extent to which naturally hydrophobic gangue particles, such as talcaceous minerals, report to the froth can be reduced by the use of depressants. Thus the use of collectors and depressants will directly influence the extent to which hydrophobic particles report to the froth. However these hydrophobic particles will also have a direct effect on the characteristics of the froth phase, more strongly hydrophobic particles causing a reduction in the stability of the froth with the expected concomitant effects on grade and recovery. This study included microflotation (ie frothless flotation) and batch flotation of various ores using a number of different collectors and depressants and a newly developed froth imaging device (SmartfrothTM). Flotation performance was characterised by mass and water recovery, and recoveries and grades of the valuables. This paper shows how the various reagents influenced the behaviour of the pulp and froth phases. The critical importance of managing the type and dosage of reagents used in flotation with a view to optimising their influence on the froth phase is discussed.

Jan 1, 2005

By R Higashi, D Maruoka, T Murakami, Y Iwami

The ironmaking industry consumes a large amount of fossil fuel derived carbon as heat source, reducing agent of iron ores and carburising agent of reduced iron. Although the demand for drastic decrease of carbon dioxide emission, carbon is an essential element for smelting process of molten iron. The carbon recycling ironmaking process by circulating CO has been already proposed to achieve carbon neutrality. However, the production of molten hot metal is not considered in this process because sufficient amount of carbon does not dissolve in reduced iron by CO. Therefore, our group has suggested a new carbon recycling ironmaking process which can produce hot metal. In this process, free carbon and iron carbides produced by carbon deposition reaction using metallic iron as a catalyst are used. It is known that only Fe3C is obtained as iron carbide by using CO gas, however, Fe5C2 is also produced by adding H2 gas. The composite agglomerated with these carbonaceous materials and fine iron ore (Deposited Carbon-Iron oxide Composite: DCIC) is reduced and melted in a furnace. It is reported that Fe3C in DCIC accelerates the reduction reaction and melting of the composite. In this study, the effects of iron carbides and free carbon on the melting behaviour of DCIC are investigated. Fe3C, Fe5C2 and free carbon were produced by vapour deposition using porous iron whiskers and CO-CO2-H2 gas. These were agglomerated with hematite reagent at a certain ratio to prepare DCIC samples with and without Fe5C2. The samples were heated up to 1300°C in inert atmosphere. The DCIC containing Fe5C2 completely melted and iron nuggets were obtained after the experiment. This behaviour was not observed in the composite without Fe5C2. This indicates that using Fe5C2 is more preferable than Fe3C for molten iron production using DCIC.

Jun 19, 2024

By P Aguilera, C Guerrero, M Tucker

With the advent of Electronic Detonator Systems in the global mining industry, as well as the development of high precision pyrotechnic delays, the measurement and analysis of delay performance (usually measured in terms of dispersion about a batch mean û precision, and the deviation of that mean from the nominal detonation time û accuracy), has become an important issue. Through the non-conventional use of existing Velocity of Detonation (VoD) measurement technology, it has been shown to be feasible to measure the precision and accuracy of delay detonator series connected in the same manner as a typical open pit bench hook up. This paper describes the work undertaken to compare and contrast performance results obtained using a range of instrumentation including High Speed Video (HSV) filming, digital counter timing using a Hewlett Packard Universal Counter and a digital VoD measurement device. The results obtained demonstrated the practical feasibility of using the latter technology in order to obtain relatively large amounts of data in a time-efficient manner, with a precision of better than 0.5 microseconds, if required. The results also confirmed the close statistical agreement obtained between the three forms of performance measurement, therefore permitting the substitution of the VoD measurement technique for the more capital cost intensive HSV technique and the slow, sample-by-sample HP Universal Counter method. This paper describes the methodology applied and the results obtained.

Jan 1, 2004

By Fejes G

An integral part of the Brisbane Suburban Railway Electrification involved the relining, refurbishment and track lowering in the Roma Street, Brunswick Street and Gloucester Street double track tunnels. The design and the construction procedures had to satisfy the Queensland Railways electrification clearance and track standards and the requirements of maintaining track services through the tunnels during work. Refurbishing of the tunnel linings was carried out to extend the life of the tunnels.

Jan 1, 1981

By Yu A. B

An experimental study of the packing of a coal heap has been carried out. The bulk density of a coal heap is considered as a function of a number of variables, viz flow rate, conveyor belt speed, the height of the disengagement point of the conveyor belt, coal particle density, moisture content, the size of the heap and coal particle size distribution. The effects of the dimensionless numbers resulting from dimensional analysis on the packing density of a coal heap have been experimentally examined and analysed. Based on the experimental results, equations have been formulated for the estimation of the bulk density of a coal stockpile. The validity of these equations are checked by comparing the predictions with measurements of real industrial Stockpiles.

Jan 1, 1991