Search Documents

By Fraser C. J

The township of Yalloum was established in 1921 to provide accommodation for the work force on the sites of the power station and open cut which were to become the basis of Victoria's electricity industry.A company town, Yallourn flourished, and in its heyday in the 1950s the township had a population in excess of 5500 residents.However the town was sited over a valuable coal field. In the 1960s, studies conducted by the State Electricity Commission indicated that excavation of this coal as a continuing development of Yalloum Open Cut was the optimum choice to meet the growing energy needs of Victoria. Operation in what became known as the Township Field commenced in 1979 and the completion of the overburden stripping was successfully achieved on target in 1991.

Jan 1, 1992

By L M. Zhang, T H. Xu, J Zhao

Blasting is one of the most commonly used strategies for excavation in civil and mining engineering. Yet blasting can also bring along such undesirable effects as ground vibrations and soil disturbance. Numerical analysis is a powerful tool for estimating the effects of blasting and improving blasting design. In this research, a constitutive model for sand is proposed for the numerical analysis of blast-induced ground motions and wave propagation in soil mass. In the model, three model surfaces, ie the critical surface, the dilatancy surface and the bounding surface, are defined following the bounding surface hypoplasticity framework. The strain rate is included explicitly into the model formulations so that the proposed model is valid under high strain rate loadings caused by blast-induced vibrations. The performance of the proposed model is validated by the simulation of drained triaxial compression tests conducted on a crushed coral sand under different strain rates.CITATION:Xu, T H, Zhang, L M and Zhao, J, 2014. A bounding surface model for sand subjected to blast-induced vibrations, in Proceedings AusRock 2014: Third Australasian Ground Control in Mining Conference , pp 201–206 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 5, 2014

A general review of grinding mill steel liner evolutions/developments in recent times. The driving force behind these developments has been the mill operators desire to minimise the nett cost of their operation. These developments have resulted from a team approach between supplier, operators and reline crews. The move towards larger diameter high aspect mills, faster mill speeds, pebble ports and the use of large diameter grinding media has affected the traditional liner designs, which is placing higher demands on the supplier to meet these new working parameters and expectations. Operators are also taking closer ownership in the liners being supplied, as demonstrated by the development of their own mill liner specifications. This paper outlines some of liner developments and changes undergone at various milling operations around Australia and overseas (such as Cadia Hill, Kidston, Ok Tedi Mining, PT Freeport, etc) and where to in the future?

Jan 1, 2000

By Ride G

The provision of a water supply is a major consideration in planning mining developments particularly in remote areas. The evaluation and development of adequate water supplies in and areas of Australia is often as important as the discovery of the orebody. The copper orebody at Warrego near Tennant Creek could not be mined economically if cheap treatment water was not available near the mine. This paper describes the difficulties in obtaining water in the Tennant Creek area and the water supply investigations carried out near the Warrego Mine which resulted in the successful discovery and evaluation of a reliable large scale water supply. It is contended that the establishment of a water supply must be approached on a systematic and scientific basis similar to the approach with the exploration and establishment of actual ore reserves. Mining companies with similar water supply problems may benefit by approaching their problem on this basis. The approach adopted by Peko Mines is outlined in this report.

Jan 1, 1980

The considerations which led to the decision to_ install discs at the Dampier Pellet Plant of Hamer ley Iron Pty. Ltd. are described. Initial testwork showed that the ore could be ground dry in open circuit to a Blaine index of 2500 cm2/g and that it pelletized readily. The various design criteria including diameter, slope, speed, motor size, depth of sidewall, feed point and water spray location were then determined. Plant performance after commissioning is described including the various problems encountered and the modifications since carried out to overcome them. The main problem was quickly identified as disc feed rate control. Various bin and bin feeder modifications were tried to overcome the effects of the fluidising characteristics of the dry ground ore. Other factors found to affect disc operation are ore size distribution, additives and operator competence.

Jan 1, 1974

By M J. Kelleher

CREAM is an acronym for coal recovery, evaluation, analysis and management and is a business improvement project at BMAÆs Goonyella Riverside mine that is focussed on maximising coal recovered. In August 2003, Goonyella Riverside was set a challenge to quantify coal loss and dilution and their relationship to cost, revenue and ultimately profit. While the mine was confident in its site forecasts of recovery (and loss), it was clear that the traditional measurement and analysis systems were inadequate to firstly, identify key loss areas and mechanisms and secondly, successfully quantify the benefit of various coal recovery initiatives. The path that BMA Goonyella Riverside has travelled to maximise coal recovered can be divided into four key steps: Mapping the process û This step involved the development of a coal flow process map for Goonyella Riverside that stepped through each component of the process from the coal reserve to the customer and identified key measurement points for the purposes of reconciliation. Understanding coal loss and identifying opportunities û This step involved conducting two detailed Reserve to Customer projects at the mine site to track a block of coal from the reserve to the customer and to gain a greater understanding of the relationship of dilution, coal loss mechanisms, revenue and costs associated with recovering additional coal. Coal data systems development û Two important coal data systems have been developed and implemented at Goonyella Riverside in the past twelve months, namely SnowdenÆs Coal Reconcilor and SeamFix. These systems enable coal losses and dilution to be quantified and reconciled back to the initial coal reserve. Implementation of loss reduction initiatives û This step involved the formation of a business improvement project referred to as æCREAMÆ in August 2004, for the purposes of improving pit coal recovery and maximising business value. To date a series of coal recovery trials have been run in a number of pits at Goonyella Riverside that have yielded significant improvements in business value. The key to the success of this project has been the discipline to follow a defined process map, management commitment through resourcing and shared key performance indicators, a successful acceptance strategy resulting in holistic ownership and the implementation of sustainable reconciliation systems. Coal loss and dilution are now quantifiable and their relationship to cost, revenue and ultimately profit is well understood. This paper discusses the process that Goonyella Riverside has adopted to maximise coal recovered.

Jan 1, 2005

The Mt Muro gold and silver deposit in Central Kalimantan has been in production since December 1994. The geology is characterised by narrow high-grade lodes containing gold and significant amounts of silver. From a largely untrained workforce in the grade control department, production per crew and per geologist has tripled during the three years of production. Grade control drilling evolved from blast hole sampling to reverse circulation sampling. National geologists are trained in basic modeling procedures. A fully integrated reporting and reconciliation system was programed and implemented.

Jan 1, 1997

By Noller B. N, Mine F. J

Modem open cut and underground mining in the tropics inevitably expose partially weathered and unweathered rocks to oxygen and water, leading to weathering and the release of solutes and often acidity as well. Historical monitoring data can demonstrate these phenomena. Three case studies from open cut mines in the north of the Northern Territory illustrate the deterioration in quality of pond water receiving drainage from waste rock dumps. The potential for deterioration of water quality was not recognised in many mine Environmental Impact Statements prepared and accepted in the 1980s. The examples documented indicate the importance of adequately planning for this near inevitable process. Retrofitting a mine water management system to 'no' or minimal release can be very difficult and expensive, and may not be feasible, leading to downstream pollution. The characterisation of acid and solute production potential of ore and waste rock, and improved dumping strategies and water management are very important to minimise the environmental impact of mining in the tropics.

Jan 1, 1994

By Jacobs M

After a methane explosion in a coal mine a pre-determined crisis management procedure is instigated. As the process rapidly evolves the inevitable question arises - are personnel trapped underground, are they alive and can they be rescued without putting the lives of the rescue crew at risk? This is a very emotive question with many sub-questions such as; could anybody have survived, is there the potential for a secondary explosion and is there a `window of opportunity' before that secondary explosion occurs?To determine if that window of opportunity exists two fundamental elements must be in place; a method of determining the atmosphere at key points in the mine and a method of predicting the course of change of that atmosphere with respect to time. The first element can be achieved if the tube bundle system is intact and drawing samples from known points, alternatively boreholes can be drilled from the surface. The second element can be realised by utilising a sequence of computer generated control charts which have a time axis, a percentage combustibles axis, the upper and lower explosive limits of the current atmosphere and a prediction option which allows the user to look at the potential changes in the atmosphere over a set period of time. These control charts would be part of the mines on-going crisis management system rather than a tool to be used after an explosion had occurred.

Jan 1, 1998

By G Brewster

The Eagle on the Hill tunnels form part of an upgrade of Mt Barker Road, 15 km to the southeast of Adelaide. The upgrade significantly improves safety and reduces delays on this major road, which winds steeply through mountainous terrain. The twin tunnels each spanning 15 metres run in parallel for a length of 480 metres. The tunnels are excavated in slightly weathered high strength slates and very high strength quartzites of the Saddleworth Formation on the western margin of the Mount Lofty Ranges. Steeply dipping slate cleavages and the high fracture ratio result in many slope stability problems in the project area. The level of geotechnical investigation undertaken prior to the calling of tenders for the project was extensive. This included the excavation of a pilot tunnel along one of the tunnel alignments, which allowed accurate mapping and rating of the rock, resulting in an increased level of confidence during the tender process. One of the features of the winning alternative tender design was the use of canopy tubes, flexible steel ribs and shotcrete to replace up to 40 metres of deep portal cuts in unstable rock with driven tunnels. Slope stability issues were overcome with the use of rock dowels and shotcrete. The support concept allowed the safe driving of the tunnel portals with as little as two metres of overburden. The design incorporated lining drainage and criteria for fireproofing based on European experience to ensure the ability of the tunnels to remain stable in the case of a severe fire incident. The support design allowed for maximum flexibility with a range of support types able to deal with the varying ground conditions. Design development and support refinement continued throughout the tunnel construction phase with close liaison between the designer and the constructor. Monitoring and review of feedback from the construction site by the Sydney based design team was easily achieved by means of electronic transfer of photographic and survey information, telephone and fax communication and regular site visits. The contractor for this project is Macmahon Concrete Constructions Joint Venture (MCCJV) and the designer is Connell Wagner. Excavation commenced in January 1998 with tunnel breakthrough having been achieved in early-August 1998 and mid-September 1998 respectively. Concrete lining construction is scheduled for completion in April 1999.

Jan 1, 1999

By P Corbett, P Sheffield

Springvale Mine is an underground coal mine in the western coalfield of New South Wales which utilises retreat longwall mining technique. The mine encountered significant gateroad floor heave issues during retreat of LW415. Floor heave has subsequently impeded longwall advance as well as longwall bolt up and recovery to some extent during the extraction of the next five longwalls. Floor heave at Springvale Mine develops throughout the lifecycle of the mine roadways, and is most prevalent in longwall gateroads. Floor heave has been measured as early as 2 weeks after roadway development and continues to develop through the post-development phase, with a rapid increase in close proximity to the longwall face. This paper presents a case study of the evolution of understanding of floor heave behaviour at Springvale Mine based on geotechnical characterisation, an intensive convergence monitoring program (roof and floor movement) and spatial correlation of monitored locations with longwall face position. The analysis considers previously known factors contributing to floor heave including mining depth, geological and physical properties of the rock mass and mine design geometry. Investigation results indicate a strong correlation between floor heave magnitude and roof dilation magnitude, geophysically inferred faulting in underlying strata, areas of localised stress concentration and mine roadway dimensions. This paper also discusses the predictive model which was developed as a result of the study, which is now the basis of the floor heave removal program used to manage roadway convergence at the mine. Floor heave monitoring, prediction and management strategies (including floor reinforcement and removal) are also discussed. CITATION:Sheffield, P and Corbett, P, 2018. Managing floor heave in an underground longwall coal mine, in Proceedings The Fourth Australasian Ground Control in Mining Conference (AusRock), pp 78–94 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 30, 2018

Mining had a very considerable effect on the country's development. The visual evidence remaining is an integral part of New Zealand history. Early mining for manganese and copper in the 1840s was succeeded by alluvial gold rushes. These gave way to hard rock extraction, hydraulic elevation and dredging. Coal mining dating from the 1850s was fairly widespread. Other minerals were obtained on a small scale. Manufacture of mining' machinery stimulated industrial engineering enterprises. Schools of mines played a significant part in advancing technical skills and several remain as museums. Surviving mine structures and site relics are part of the industrial heritage signifying the technological and economic development of a small isolated nation. Some of these are described. Identification, recording and preservation where practicable is advocated.

Jan 1, 1990

By Matthew SP, Hayes PC

The product morphologies formed on the reduction of dense wustite crystals are classified into three types,A) porous iron, B) porous wustite covered with dense iron and C) dense wustite covered with dense iron. The mechanisms of formation of these structures and the effects of impurity elements on the product morphologies are discussed

Jan 1, 1984

The industrial practice of separating finely' around valuable minerals from associ- ated gangue materials by froth flotation is well known. Despite the obvious importance of this industrial process, the predictive tools for plant engineering evaluation of flotation process variable changes are still in a developmental stage. Consider, for example, the situation where an operating engineer is faced with evaluating a change in an existing chemical reagent scheme, possibly based on batch laboratory data. When all is said and done, the engineer must still perform detailed physical testing of the proposed reagent change on the actual equipment in plant use to be confident even of the direc- tion of change of plant results, let alone the economic viability of the change. The theory behind chemical reagent behaviour in froth flotation has been studied extensively, e.g., (Aplan {1980}, Fuerstenau {1976}, Fuerstenau {1962}, and Somasundaran {1980}), and, certainly, important progress has been made. Unfortunately, the nature of the flotation process, with its complicated heterogeneous surface chemisty activity operating on highly variable and difficut to characterize ore surfaces, coupled with com- plex mass and momentum transfer phenomena, :;l riously compromises the plant scale predictive capability of theoretically based models.

Jan 1, 1978

By Smith I. T

Mine operators have long recognised that the results achieved in primary blasting are critical to subsequent mining activities. With the introduction of "in the hole" drills under- ground and the advantages offered by the use of water gels in conjunction with ammonium nitrate-fuel oil (ANFO) explosives, new mining methods have been developed and enabled improvements in older methods. Pumpable water gels have been used with varying success underground. These gels allow a high loading density even in ragged bore- holes. The problems encountered with slumping in upholes is recognised so the current trend is to use these gels in downholes where wet holes are prevalent. Cartridged water gel technology has advanced to the point where it has allowed the replacement of nitroglycerin (NG) based explosives and pumpable water gels. Today, gels can be made as a tampable product for use in development headings or as a slump- ing product for downholes to give an effective coupling. With the introduction of the Tovex« pneumatic loaders, the problems associated with a pumpable gel were eliminated and gave the user the ability to alter his loading density.

Jan 1, 1977

Initial coal production at Ulan was solely from underground mines. A significant increase in demand for steaming coal in the late 1970's emphasised the need to further expand production and led to the development of the open cut mine which commenced commercial production in June, 1982.During the initial stages of mine planning, feasibility and cost studies were undertaken to determine the most suitable method for coal haulage from the pit. The comparison between a conventional truck haulage system and an in-pit crushing system using a mobile crusher and moveable belt conveyor haulage confirmed that the mobile crusher and conveyor system was superior in every respect for the Ulan mining operations.Technical features and design parameters for the major items of equipment are outlined as well as operating, manning and performance assessments. Minor equipment problems were encountered during initial operation but these have since beenrectified and the plant is now capable of exceeding the design production. Maintenance and energy costs are considerably lower than originally estimated and production efficiencies are continually improving as operators develop new techniques and procedures in the handling of the equipment.

Jan 1, 1985

By Medhurst TP, Trueman R, Hutchinson IN

A breaker line support (BLS) monitoring system, BLSmon, has been designed and constructed by the CSIRO and installed and commissioned at Laleham No.] Colliery, Queensland. This system was designed to record hydraulic leg pressure and canopy position measurements and relay these, in real time, to the surface. The system has shown itself to be capable of operating on the BLSs without any adverse affect on production. Analysis of the results of the monitoring exercise has shown that rate of change of leg pressures on the BLSs could be used as an aid in the prediction of adverse mining conditions. Under favourable mining conditions the supports were observed to initially unload from the set pressure, this unloading reduced with time and by the end of a typical lift cycle had either ceased or reversed slightly. This behaviour was considered to be due to one of four possible causes, these being; the compaction of floor debris, and/or compaction of the floor, and/or crushing of the roof and /or support creep. The actual cause can only be determined through detailed monitoring of both roof and support convergence. However observational data would suggest that compaction of debris and softened floor material beneath the supports was the most likely cause. The few positive loading rates recorded under these conditions were of short duration and occurred towards the end of individual lifts. Where mining conditions were unfavourable the negative rates of change of pressure, unloading of the support, were reduced throughout a lift, in both duration and magnitude, when compared with favourable mining conditions. Over the same period the positive rates of change were observed to be greater. The rate of change of loading and convergence can be utilised to identify the onset of instability in the lift area. However, before this facility can be utilised by the mine for the reliable prediction of instability more monitored data and sophisticated processing techniques are required.

Jan 1, 1992

By B N. Morrison

In all metallurgical plants metallurgists require analyses of the various intermediate products, eg flotation feeds, flotation concentrates, tailings, mattes, slags, etc to monitor the efficiency of the plant processes and for plant control purposes. Traditionally these samples have gone to off-site laboratories and there can be some considerable delay before analytical data are received. On-line monitors have to be used for plant control purposes and these are difficult to maintain and can give poor quality data. Recent technological advances in automation in analytical laboratories now allow a far quicker turn-around time for analytical data so they can be of more use to the metallurgist. Automation, which involves the use of robots and fewer people in laboratories, has the added benefit of providing higher quality data as the possibility of human error and bias is minimised. Differences between conventional manual laboratories and automated laboratories are described. Automated analytical laboratories are now becoming the laboratories of choice for mining companies which require large numbers of samples to be analysed on a 24/7 basis on similar sample types using the same sample preparation methods and analytical procedures. Automated laboratories have now been installed in platinum, iron ore, copper and aluminium producing mining companies. A further advantage to metallurgical plants is now the possibility of siting automated analytical laboratories in-plant and designing the plant around the laboratory. Concentrator streams, slags, etc can be sampled by automated samplers, the samples transferred by automation to the in-plant laboratories and all sample preparation and analyses carried out by automated processes. These laboratories require a minimum of staff. Such automated in-plant laboratories have been installed on a platinum mine flotation plant, a platinum mine smelter and steel plants. One is in process of being installed on an iron-ore mine with the sampling being carried out by an automated sampling tower. The procedures followed in planning an automated analytical laboratory for a metallurgical plant are described in detail in the paper. The platinum plant smelter automated system which includes rapid transport of samples by air-tube to the laboratory for the analysis of the samples by XRFS is also described in the paper. It is concluded that automated analytical laboratories can be retro-fitted to most metallurgical plants but they are best suited to greenfield sites.

Jan 1, 2008

At Hilton Mine, 18 kilometres north of Mount Isa, the silver-lead-zinc sulphide bodies have undergone strong deformation in the form of folding and later faulting and brecciation in the hangingwall region of the mine. Variation in grades and widths over compara- tively short distances causes problems regarding accurate sampling of orebody exposures in underground development, and in defining confidence limits for the extrapolation of ore intersections in ore reserve calculations. The paper gives a preliminary insight into the problem of obtaining representative samples for exposed orebodies and discusses the sampling techniques employed. Results gained from these sampling methods could not be verified due to lack of individual bulk samples for comparison but strong evidence for precision was provided. INTRODUCTION In a developing mine like Hilton, accurate grade information is of extreme importance. Original grade information for a potentially viable ore deposit is gained from surface drilling, and initial ore estimates are calculated from the resultant ore widths and grades. After underground development has proceeded, the opportunity arises for detailed examination of orebody exposures, and the resultant assay grades and widths from sampling of these exposures may, in the long term,

Jan 1, 1976

THE plant is one of the usual type of Mond plants, and contains no new features worthy of comment. A brief description of the process, however, with a few remarks on the working of the plant, may prove of interest.Producer gas is made by passing a mixture of air and steam through incandescent carbon contained in a furnace called a producer, which, in the Mond type, is a cylindrical casing of steel plate, lined with firebrick, and fitted at the lower end with sloping fire-bars'. Coal crushed to an even size (about 2-in. gauge) is elevated to bunkers over the producers, from which it is fed into a measuring hopper on each producer.The hopper is a cast-iron cylinder fitted with a swing cover at the top and a bell valve at the bottom, worked by a lever and balance weight. When a charge of coal is run from the bunker into the hopper, the cover is closed, and the bell valve is lowered, allowing the coal contents to drop into the producer. Thus no gas can escape from, or air be admitted to, the producer during the process of charging. The hopper discharges its coal through a steel pipe-shaped container called the bell, which projects about 9 in. through the roof of the producer. The function of the bell is to spread the coal evenly over the fire, and supply coal to any portion of the fire as it settles.

Jan 1, 1918