Search Documents

By Swayn G. P, Floyd J. M

BHAS, together with the G.K. Williams Laboratory, and Ausmelt Pty. Ltd., has examined a number of possible alternatives to conventional silver cupellation in gas fired reverberatory furnaces. Of these alternatives, a Sirosmelt furnace was preferred for both technical and economic reasons. Small scale work on Sirosmelt processes was carried out at the G.K. Williams Laboratory at Melbourne University in 1985/86. Pilot scale work was carried out at the Ausmelt plant in Melbourne in July 1987. Board approval for construction of a full size plant was received in October, 1988, and construction of the plant is currently underway. The plant is expected to provide significant savings in operating costs and silver inventory. Hygiene around the furnace should also be greatly improved. An increase in cupellation rate of at least ten times is expected, compared with the conventional reverberatory furnace.

Jan 1, 1989

By R R. Lovel, G J. Sparrow

Currently there are large reserves of good quality iron ore near to existing infrastructure that are not being developed because the phosphorous levels are above acceptable market specifications. Since the high phosphorous content is considered to be mainly associated with the goethite fractions of the ore, attempts were made to leach the phosphorous from the ore after a heat treatment to dehydroxylate the goethite. Heating the ore and leaching with 40 g/L NaOH lowered the phosphorous levels from 0.145 wt per cent P to 0.075 wt per cent P or lower, but a heating temperature over 800¦C was required to achieve this reduction in phosphorous levels. However, when sodium hydroxide was added to the iron ore before the heat treatment, similar phosphorous removal was achieved with a heating temperature of 300 - 350¦C. It was considered that dehydroxylation of the goethite in the presence of the hydroxide makes the phosphorous available for removal with a water leach. As well, 50 per cent of the silica and 60 per cent of the alumina in the ore were also removed in the leach, but some sodium remained in the leach product. Further work is required to remove the residual sodium to produce a marketable product.

Jan 1, 2009

By M Robotham

In April 2013, Rio Tinto Kennecott Copper’s (RTKC) Bingham Canyon mine experienced what is arguably the world’s largest ever in-pit slope failure. The failure initiated along a major, continuous, low-strength bedding fault, named the Manefay bed, and comprised approximately 145Mtonnes of rock and waste dump material. Initial East wall slope deformations were detected some months prior to catastrophic slope collapse by RTKC’s slope monitoring systems. However, the failure mechanism was different to that which had historically been experienced in the prior more-than-100 years of open pit mining. Failure occurred as two separate events, the initial one likely consisting of a frictional failure of rock materials along the Manefay bed itself, before a second phase of failure occurred, which included a large mass of old rail dump material. The combination of these events led to a much larger failure run-out than had been anticipated by the RTKC team which led to loss of, and damage to, mining equipment and infrastructure as well as significant interruption to mining activities. Due to the diligent monitoring of the slopes no safety impacts were experienced at the mine, and as such the details and learnings from this failure can readily be shared with the broader mining and geotechnical industries to avoid similar recurrences elsewhere. This is an extended abstract only. CITATION:Robotham, M, 2018. Bingham Canyon Mine – from adversity to excellence, in Proceedings The Fourth Australasian Ground Control in Mining Conference (AusRock), pp 3–4 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 30, 2018

What is the real value of your data?Given that the cost of collecting and analysing an individual sample is always rising, it is important to understand the true value of a sample and that you are confident that you receive good value for your exploration dollar. Unfortunately too many samples are still collected today that will end up as worthless data; a liability to those who own it and a hindrance to finding that ore body.

Jan 1, 1986

By T Soares, P Esteves, C Senna, V Souto, E Dias

Steinert provides a wide portfolio of Sensor Based Sorting (SBS) technologies, including the possibility to combine different sensor data in the development of the separation applications. This multi sensor approach provides a larger applicability and extensive flexibility for the technology. This effect is emphasized for mining applications, once every ore body presents its own features that can also comprise a large material variability. In this sense, every sorting application is customized and comprises a personalized solution. This means each project development includes a test work stage that approaches from the project discussion, test definition, up to test outcomes and processing development. In relation to very complex and large projects, a sorting pilot scale plant has become a crescent tendency. By having a pilot plant stage can represent a chance to test larger amounts of material from different mining areas, different mining projects, such as to consider different processing targets and application approaches. Based on that, a better understanding about the technology application can guide a more assertive development of large and complex ore sorting projects. The aim of this paper is to provide information about the applicability of the Steinert multi sensor technology at different pilot plants in South America. It consists in a compilation of laboratory test results, plant design and operational results. For that, a chromite, an IOCG deposit and a sulphide gold ore projects are presented. Additionally, the paper discusses the application of different sensor technologies combinations such as various processing targets, thus providing a wider understanding about sorting applications and flexibility.

Nov 10, 2020

By Canterford J. H, Sparrow G. J, Dyson N. F

Pressure leaching of a bulk flotation concentrate prepared from a complex Cu-Pb-Zn sulphide ore was carried out at 150 and 190¦C under 1050 kPa oxygen overpressure in 1 L and 4 L titanium autoclaves to extract zinc, and to obtain residues for smelting tests and leach liquors for purification and recovery of the zinc by electrowinning. Dissolution of 95% of the zinc was achieved at both temperatures. Copper and iron dissolution and the degree of oxidation of the sulphide sulphur to elemental sulphur or sulphate depended on the temperature of the leach. At 190¦C, a jarosite (a basic iron sulphate) was the major iron-containing material in a residue that contained 17% total sulphur. Its formation was associated with dissolution of 18% of the iron. At 150¦C, oxidation of the sulphide sulphur and dissolution of the iron were significantly less. Only 7% of the iron was dissolved and a residue containing 25% total sulphur, present as a lead jarosite, lead sulphate, and elemental sulphur, was obtained. The formation of small pellets of unreacted sulphides coated with elemental sulphur caused problems during the leaching at 150¦C, and also during scale-up from the 1 L to the 4 L autoclave at 190¦C. At 150¦C the concentrate required two stages of leaching to achieve dissolution of over 90% of the zinc. These problems are discussed.

Jan 1, 1989

By C Young

The identification of Critical Risks, their associated Critical Controls, and the implementation of processes to ensure their ongoing management can be difficult and resource intensive. Answering the following Critical Risk Management related questions can be challenging: • What is a Critical Risk? • What is a Bow-tie Analysis and when should it be used? • What is Critical Control? • How is the effectiveness of a Critical Control assured, and how is this measured? • Who is responsible for managing Critical Controls? • What are the implications if a Critical Control is not effective? It appears that in the mining industry’s efforts to implement the Critical Control Management Process outlined by the International Council on Mining and Metals (ICMM), instead of embedding an integrated, well understood, value adding process, we have instead created a resource hungry monster that is poorly understood by numerous layers of the organisation.

May 5, 2022

By Stevenson I, Dickinson W, Taylor R. N

Despite flash smelting's widespread use little is known about the actual processes taking place in flash furnace shafts and comparatively few reports of sampling campaigns have appeared in the published literature. his paper reviews the previous reports of the use of horizontal trough samplers and analyses their expected collection efficiency. In the light of the deficiencies revealed by this analysis an isokinetic sampler was produced and a vertical sampling technique was also developed to obtain samples from directly below the burners in the shaft of the flash furnace at the Kalgoorlie nickel smelter. Comparison of the sizing of the samples obtained with the horizontal trough and isokinetic samplers confirmed the theoretical analyses and showed that the trough samplers were not collecting the fine particles. Besides providing data to validate mathematical models of the burners and shaft, chemical analyses of the shaft samples showed that the coal in the charge was reacting preferentially and that the plume of at least one of the burners was being deflected from its axial position. In the region directly below the burner there was evidence that the disperser on the burner was imparting more momentum to the coarser particles and that these were concentrating in the outer regions of the particle plumes issuing from the burners.

Jan 1, 1992

North Eastern Russia encompasses the northern part of the Circum Pacific. The region comprises various tectonostratigraphic terranes, including cratonic blocks, fragments of volcanic arcs, accretionary wedge terranes, oceanic crust and passive continental margins. The terranes have been accreted to the eastern margin of the Siberian Craton in the Late Mesozoic. The prominent structures of the region are extended zones of the Mesozoic flysch and turbidites. Another important structure is the 3000 km long Okhotsk-Chukotka volcanic arc which marks the Cretaceous active continental margin of northern Eurasia. The youngest structure of the region is the 2000 km long Late Cainozoic Kamchatka-Kuril island arc system. North Eastern Russia is the main gold producing region of the Russian Federation. Since the beginning of recorded gold production in 1932 until 1995 the region has produced 2575 t (83M oz) of gold. Most of it, 2439.5 t, has been produced from placers. Owing to depletion of alluvial gold resources, exploration and mining emphasis is currently switching to the development of the lode deposits. At least five distinct types of the gold mineralisation are reported in North Eastern Russia - mesothermal gold mineralisation in the Mesozoic fold belts, Paleozoic epithermal gold mineralisation occurring within Omolon block, epithermal gold mineralisation related to the Mesozoic volcanics, Cainozoic epithermal gold mineralisation, gold-bearing Cu-porphyry deposits. The current paper introduces the metallogeny of lode-gold deposits of North Eastern Russia. It provides the review of the regional geology, the selected gold provinces and representative deposits with an emphasis on the mineralisation styles and distribution control.

Jan 1, 1999

By Larke R, Warnock J

Although Western Mining Corporation has been producing high grade nickel ore at Kambalda since 1967, it has only recently become a significant gold producer.The main source of Gold ore has been the Victory Gold Mine located 17 kilometres South of Kambalda.This mine produced small tonnages of high grade gold ore from a sediment horizon within a complex sequence of mafic flows, in the 1890's, early 1900's and 1930's.Today, mining is centred around 2 com-pletely different ore bodies named Victory and Defiance, and involves several different mining methods. This paper describes the Operation's history and gives an outline of the proposed stoping methods.

Jan 1, 1984

By J J. Grobler

The George Fisher Underground Mine at Mount Isa applies the long hole open stoping methodology. During the reconciliation process of transverse stopes in the George Fisher North mine it was identified that excessive underbreak was regularly experienced, with the major contribution coming from the toe area inside the stope.While over break and the resultant dilution was well investigated and well understood, limited work was done on underbreak improvement. It was decided that a re-engineering process would be followed in an attempt to improve results. The prevailing stoping practices were scrutinised and the possible causes were listed.Some of the identified causes were design, drilling accuracy, equipment condition, mucking practices and direction of firing. It was identified that in most instances the underbreak was initiated in the slot area of the stope during the first firings. Once this happened, it was impossible to get good recoveries on the rest of the stope. The slot area was carefully scrutinised and the blasting practices were changed individually.During the following two years several different strategies were trialled to increase the toe recoveries. The results indicated an overall improvement of six per cent reduction in underbreak on average, by ensuring drilling accuracy and changing the direction of firing. The economic significance of these results outweighed the time and additional work load expended to establish the cause of the problem. This paper outlines the continuous improvement process undertaken to identify and rectify the major contributing factors to the problem. It also presents a set of recommendations to be followed in order to achieve positive results.

Mar 21, 2011

Employing gravity recovery for coarsely liberated gold and sulfide ores has potential to lead to a signifi cant reduction in the energy required for comminution and ultimately can have a significant impact on gold processing. Most of the recognised metallurgical tools at our disposal currently have been designed around recovery of relatively finely ground minerals. In order to change the paradigm of fine grind for liberation, a new set of tools need to be recognised that are capable of separations in the coarser size fractions. Some of these tools already exist and some need to be developed but the key is the way in which the fl ow sheets are arranged. A very strong understanding is required in the existing tools and their capabilities before these new flow sheets can be optimised. Only when we understand the existing gaps in technology can we start to fill these positions with new candidates. Many ores when crushed liberate their gold bearing minerals at coarser sizes than current practice would suggest (Figure 1). In order to characterise this response in ores it is necessary to utilise some new techniques in the lab such as gravity separation and ore sorting at the sizes greater than 15 mm followed by gravity recovery on fractions from 15 mm down to 150 ¦m. The most difficult range has been the mid-sized fraction from 4.0 mm down to around 150 ¦m. This is the size range in which many ores show economic liberation starting to occur and coincidentally this is the range in which many commonly used metallurgical processes reach their operational limits due to physical constraints. Examples of these processes are flotation, hydrocyclones and whole ore leach in agitated tanks which are currently the mainstays of the processing fraternity. This is an ABSTRACT ONLY. No paper was prepared for this presentation.

Aug 1, 2010

By J A. Wells, K G. Thomas, R F. Dewhirst

"One of the contributing factors to the extreme cost escalation in the first decade of the 21st century was the increase in the amount and cost of engineering work that went into studies and projects. Various reasons for this were identified, including unsatisfactory productivity due to a shortage of experienced/qualified engineers, the increased complexity and infrastructure requirements of many projects due to location, metallurgy that is more challenging and increasing environmental and social requirements. These conditions often led to unsatisfactory project results in terms of cost and schedule blowouts and created a loss of confidence – both internally and externally – in the industry’s ability to complete projects on time and on budget.Technical fundamentals aside, the experience and effectiveness of project teams has had, and continues to have, a major impact on project cost, schedule and ramp-up to nameplate capacity and operating parameters. There are unfortunately too many examples of where project teams have not been as effective as they could or should have been, all to the ultimate detriment of the project.Using the authors’ extensive experience on both owner’s and engineer’s teams, this paper discusses some of the main reasons for suboptimal team, and hence project, performance and offers thoughts on how best to build and maintain project teams. The analysis and conclusions drawn are built around the Tuckman model of group development known as ‘forming-storming-norming-performing’, which was first proposed some 50 years ago. Given the importance of good teamwork to project success, understanding how project teams grow and become efficient and productive is an essential part of good project management that should receive more attention.CITATION:Dewhirst, R F, Thomas, K G and Wells, J A, 2016. Building and maintaining effective project teams, in Proceedings Project Evaluation 2016, pp 38–48 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 8, 2016

By C G. Ryan, D R. Cooke

The Thames gold-silver deposits are part of the Hauraki goldfield, situated within the Miocene to Pliocene calc-alkaline Coromandel Volcanic Zone (CVZ). The Waitangi vein system is one of the mineralised ore shoots in the Thames district. The Thames gold deposits are characterised by shallow-level epithermal vein mineralisation with phyllic to advanced argillic alteration assemblages and abundant sulphide minerals including pyrite, arsenopyrite, chalcopyrite, galena and sphalerite. Gold occurs as electrum in association with sulphide minerals. Sulphur isotope analyses of mixed sphalerite-galena and sphalerite-galena-chalcopyrite samples yield a narrow range of δ34 SCDT values (-1.0 to 0.9 ë; n=5), whereas late spongy pyrite gives unusually light sulphur isotope values (-16.7 to -27.9 ë; n=4). Vein quartz from the mineralised zone at Waitangi yields δ18OSMOW values from 6.8 to 12.7 ë (n=23). Fluid inclusion studies indicate a homogenisation temperature range of 190¦ - 296¦C and salinity range of 0.2 - 3.0 wt per cent NaCl equivalent. Similar temperature and salinity ranges have been recorded for the other gold deposits in the Coromandel Peninsula. PIXE (Proton Induced X-ray Emission) analysis revealed that the Waitangi ore fluids have 1090 - 2700 ppm K (average 1600), 145 - 205 ppm Ca (average 180), 80 - 100 ppm Mn (average 90), and 80 - 200 ppm Fe (average 120) but no detectable Cu, Zn, Br, Rb, Sr, Pb and Bi (only one fluid inclusion contains 28 ppm Zn). The sulphur isotopic values of base metal sulphides from Waitangi suggest that the sulphur was derived from a magmatic source (either directly, or by leaching of igneous sulphides). The calculated oxygen isotopic composition of ore fluids is between -2.1 to 3.8 ë at 250¦C and -0.1 - 5.8 ë at 300¦C. Oxygen isotope analyses have revealed significant variations in δ18O values with elevation and gold grades. Zones of gold enrichment coincide with a zone of variable oxygen isotope values at the top of the vein system, where boiling and/or fluid mixing most likely occurred. Mixing of ore fluids with convective ground water is a likely mechanism for gold deposition in a shallow environment for the Waitangi vein system and there is also lack of fluid inclusion evidence (eg liquid-rich and vapour-rich inclusions in the same growth zone) for boiling of ore fluids. Oxygen isotope values varying with gold grades within the Waitangi conduits suggest that δ18O values may be useful in targeting bonanza grade gold mineralisation in epithermal vein systems.

Jan 1, 1999

By B J. Andrew, M R. Daley

Mount Isa Copper Mines is a world-class mining operation producing approximately six million tonnes of ore per annum. With over 50 years of mining history and over 76 million tonnes of underground resource remaining there are many challenges facing the mine technical team today and into the future. The mine consists of nine distinct areas: the Hangingwall Lens, Footwall Lens, 1100, 1900, N1100, N1900, 3000, 3500 and N3500 orebodies. Each of these areas have different characteristics, requiring varying methods of mine design and ground control for safe and efficient orebody extraction. Each of the areas operate with an independent sequence whilst interacting with the entire underground operation. Within the first five years after graduating mining engineers tend to orient their careers in either a technical or operations direction. Engineers working towards a specialised technical career will often be working as mine planning engineers, whilst others more focused in the operations stream occupy roles such as operations or project engineers. At this stage of a mining engineerÆs career they are not yet categorised into one stream or another, but career decisions made now can generally focus their ultimate career path in one direction or the other. Due to the size of the Mount Isa operations there are many opportunities for engineers pursuing both career path and plenty of room for growth forthose as yet unsure.

Jan 1, 2005

By B T. Qin, C Zhu, Y W. Jia, Y Lu, F L. Li, Q L. Shi

Air leakage through rock fractures in coal mining is a major cause of coal spontaneous combustion. In order to overcome the deficiency of the existing fire control technology and prevent coal spontaneous combustion by isolating coal from oxygen, the article proposes a novel technology of inorganic solidified foam (ISF) with high expansion to fill fractures effectively. ISF consists of fly ash, cement, setting accelerator, redispersible polymer powder, water and aqueous foam. For preparing homogeneous and stable ISF, a preparation system with a pore type foam generator, a mixer device installed with a hollow shaft and helical blades, air compressor, slush pump and monitoring instruments was developed, and the working principles of key devices were elucidated. Based on a series of experiments on the different ratios of each component material and technological parameters of the preparation system, ISF with a foam expansion ratio of 8~10 and dry density of 250–400 kg/m3 was prepared. The relationship between elastic compressive strength, modulus of elasticity and density was summarised. Based on the injection experiment for fracture of loose coal pile with high temperature, the characteristics of sealing air leakage, compressive strength, thermal insulation, flow and cooling of ISF in the fresh state were investigated, indicating that ISF can effectively cut off the air leakage and cover the coal sample to reduce the temperature in the earlier stage, and ISF can remain stable and not crack. The ISF was applied to Luwa coalmine to seal small coal pillar pressure fractures and loose coal fractures in goaf. After press-casting the ISF in Luwa coalmine, the pressure-difference of inner-outer increased, meaning the effect of external conditions on the pressure-difference decreased, showing that it could plug the air leakage effectively.CITATION:Qin, B T, Shi, Q L, Lu, Y, Zhu, C, Li, F L and Jia, Y W, 2015. The novel technology of inorganic solidified foam with high expansion for preventing coal spontaneous combustion, in Proceedings The Australian Mine Ventilation Conference, pp 121–126 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 31, 2015

By P J. Fairfield

"This paper reflects on the author’s experiences in undertaking mining studies and reviewing mining projects and technical reports, particularly over the past five years, and the impact of recent changes in reporting standards and listing requirements pertaining to mining-related evaluation and valuation exercises. It also discusses contemporary changes in the expectations of the investment community and the implications for the role of the technical specialist in providing advice to such stakeholders.Not for the first time in history, the resources industry has experienced a significant downturn after a period of strong, sustained growth in line with the traditional view of the cyclical nature of commodity markets. The resource industry is currently faced with capital austerity in the wake of projects ‘failing’ (not delivering to expectations). In response, the industry has experienced changes in investment behaviour (slowing of investment) and an increasing regulatory burden as stakeholders seek a greater understanding of mining project risks.This paper discusses this response and uses case studies to highlight the key learnings (perhaps re-learnt) by the industry. It also discusses the challenges faced by technical specialists in communicating the results of technical and valuation studies to the investment community.As investors seek to take advantage of the current stage in the investment cycle, the key challenge of the technical specialist is to effectively communicate the uncertainty in technical assumptions, risks and opportunities that drive project value.CITATION:Fairfield, P J, 2016. Managing expectations – from buyer beware to buyer be aware, in Proceedings Project Evaluation 2016, pp 66–74 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 8, 2016

By A Stradling

For a geometallurgical program to be successful, linkage must be made between the geologists and geostaticians who understand and model the orebody, the metallurgists who determine the value that can be extracted from the different geometallurgical units, and the mine planners who develop and optimise the plan to extract maximum economic value from the resource. One of the primary purposes of geometallurgical models is in the determination of the economic cut-off between ore and waste. Recognition of the level of confidence required in the estimation of grade, throughput and recovery is critical to the planning of a successful geometallurgical program. It also helps clarify the scope of work needed to mitigate risk at each stage in the development of a new mine projectThis presentation provides some of the author’s experience with development and application of geometallurgical models for existing base metal operations. It discusses how geological units defined by lithology, structure, alteration etc, can be translated into geometallurgical ore types defined by mineralogy, ore hardness, and flotation behaviour. Examples of how these characteristics have been used to estimate key economic parameters such as mill throughput and flotation recovery at two brown-field operations are provided. The first example relates to the modelling of metallurgical performance at Teck’s Red Dog zinc-lead mine in Alaska. Prior to 2000, zinc, lead and silver recoveries from a block of ore at Red Dog were either assumed constant, or were varied according to simplistic models. Throughput was not thought to vary substantially between blocks, so an average value was used for each blended stockpile. It is quite possible that some ore-value blocks were classified as waste, and some waste-value blocks treated as ore, as a result of poor understanding of the true economic cut off across the wide range of ore types observed at Red Dog. After an extensive flotation test program, the first assay-based zinc recovery model was developed for the Main pit reserve in 2003.**This is an abstract only. No paper was prepared for this abstract**

Sep 5, 2011

By S Pontual

The use of spectral data has traditionally been for obtaining mineral information and for mapping out alteration systems. The output from these data is typically in the form of mineral assemblages and data on relative proportions of minerals. However there is much more than just mineral information in the spectral data. Most importantly, the data allow the user to obtain vital information on mineral chemistry for some key alteration minerals. The mineral chemistry data allow the users to evaluate multiple phases of alteration of the same key mineral species, and to assess which phase is related to mineralisation. Mineral indices can be extracted from the spectral data and plotted to represent variations in the chemistry and relative proportions of key mineral phases as downhole, section and three-dimensional (3D) plots. These data can also be compared with the spatial distribution of the mineralisation by integration with geochemical and logging data. Through spatial and statistical evaluation the mineral information obtained using spectral analysis can provide vital information to assist in building alteration models and therefore improve targeting for further drilling and exploration.

Aug 22, 2011

By S Munn

Today, it can be said that the majority of mines utilise communications equipment in one form or another. Either for communications between staff making their day-to-day operations more efficient, or for emergency communications, as well as linking computer based mine management systems, and providing remote control over complex mobile and fixed machinery. With the advances in technology now available, we are moving into the next generation of mine communications equipment, using digital communications in the underground mine environment. It is a proven fact that an efficient underground mine communications system can help maximise production, by providing major gains in areas such as equipment and manpower utilisation, staff and vehicle tracking, reaction times to break downs and emergencies. In this paper we will describe some of the facilities that are currently available, as well as what will soon be available to mining and tunnelling companies around the world.

Jan 1, 1999