Search Documents

By J Franke, C Gonzalez

One of the regular tasks of geotechnical and mining engineers is the measurement and management of deformation in underground excavations. Although several methods are used to do so, the incumbent methodologies for monitoring deformation and ground support serviceability are limited to the use of visual observations or measurements at discrete points, resulting in a qualitative assessment only. The introduction of LiDAR technology allows a quantitative assessment across the entire excavation volume and its rock surface, by collecting a full three-dimensional image of the entirety of an excavation such as an underground drive, decline, or a tunnel. Comparisons between epochs of complete 3D data coverage allows for change detection over time that doesn’t feature otherwise typical omissions. The implementation of regular scanning has shown to be highly advantageous for mines with swelling or squeezing ground, but also at mines with rapid deformation. Despite the LiDAR potential, its adoption has been slow. A key reason for that is that working with point clouds is foreign to most geotechnical engineers. Point clouds have long been the realm of surveyors, but to fully adopt their use in geomechanics requires retraining, upskilling, and devotion by the individuals and the company. Sites are already stretched, so often there are insufficient resources to be applied to bringing the new technology into use. The solution to this hurdle is to partner with subject matter experts to achieve the desired high-quality outcomes without the commitment of time by geotechnical personnel. This paper presents a new solution of fully automated raw LiDAR point cloud data processing that not only enables geotechnical engineers to avoid having to learn unrelated skills by allowing for deformation monitoring without associated training or expertise, but it also provides instant reporting results as well as a sophisticated database with features otherwise not available. All data processing time and effort is completely replaced by an automated process which at the same time opens up the opportunity to monitor many more excavation volumes at a higher frequency than is possible with conventional tools and methodology.

Nov 29, 2022

By Lloyd F, Bayley F. J

The new South Mine in the Western Deep Levels complex is destined to become an ultra deep project extending to depths of 4 200 m below surface and where rock temperatures are likely to exceed 65 ¦C. Initial estimates put refrigeration requirements at 133 000 kWR. A surface refrigeration plant with an initial capacity of 42 000 kWR has been commissioned and will be used for mining the upper levels.

Jan 1, 1988

By Dyson NF

Nickel sulphide precipitated from waste liquors at the Yabulu plant of Queensland Nickel Pty Ltd was pressure leached under various conditions. Leaching at 130¦C and 700 kPa of air dissolved 95 per cent of the nickel as the sulphate in less than 2 h. Leaching at 130¦C and 350 kPa of oxygen dis- solved 95 per cent of the nickel in less than 1 h. Dissolution was faster with oxygen than with the equivalent pressure of air. Crystallization of hydrated nickel sul- phate from the resulting clarified leachate is readily achieved. Because the sulphide pre- cipitate also contains minor amounts of iron, copper and cobalt, the crystallization product contains these metals in excess of the amounts required for electrolytic-grade nickel sul- phate. This grade of product could only be produced if the contaminants were removed prior to crystallization. Alternatively, the "crude" nickel sulphate could find a market as a feed for the electrolytic production of Ni-Fe coatings.

Jan 1, 1984

By L A. Balzan, F Nieuwenhuys

GEOSCAN on belt analysers have been widely utilised in iron ore for nearly two decades. Since the first installations in 2003, the availability of accurate and reliable grade data has become standardised across iron ore mines in the Northern Cape in South Africa, where various streams are monitored continuously to ensure the optimal functioning of plants. Assmang Khumani has been at the forefront of technology adoption, and has implemented 19 GEOSCANs at various locations throughout the plant, monitoring run-of-mine, stockyard feed, beneficiation plant feeds, and products. Over the years, collaborative advances in the technology have allowed for numerous benefits and gains to be made. In recent times, there has been a concerted effort on the development of analysis for phosphorus in the material flows, and based on Scantech’s experience in the phosphate industry, this element has now been calibrated to achieve statistically acceptable and repeatable accuracies for real time analysis of this element on many of Khumani’s GEOSCAN analysers. This paper provides an overview of GEOSCAN use at Khumani, while focusing on the development of phosphorus analysis. A case study of analysis results is presented for a range of analysers that have been calibrated for this element, as well as a discussion on the benefits obtained as a result of this analysis.

Nov 8, 2021

By B Beale

Bow-tie analysis is a commonly used tool to identify and display risks that have the potential for an undesired hazardous event. The output of the analysis are bow-tie diagrams, which are an effective and versatile communication format that can be applied to any type of risk. Contrary to their simplicity, a proper bow-tie diagram that maintains its usefulness and clear communication is difficult to build. Over two decades assisting Major Hazard Facilities with bow-tie analysis for Safety Cases, several common mistakes have been identified. This paper aims to highlight those issues with examples and provide improvement strategies. A sample of the most common mistakes are: - overly complicated risk analysis - poorly scoped and defined terms - poor descriptions and justifications - identifying too many dependent controls. Overly complicated risk analysis leads to wasted time in obtaining data for little gain. The bow-tie diagram is only a model. Effort should be redirected into identifying and managing controls that will make a tangible difference to site risk. Broad scopes lead to enormous and confusing bow-tie diagrams for both the user and the workshop team. Defining the scope of the study, the consequence severity of interest and critical control characteristics creates focused workshops and targeted analysis. With more definitive scope, there may be more bow-tie diagrams, however, they are succinct and specific. Well described causes are imperative for clear communication to users, regulators and future bowtie review workshop groups. It is best to use common wording structures and explain the event stepby- step. Also, clearly document any likelihood calculations and use data references where applicable. Identifying all possible controls creates a false sense of security that there are many layers of protection. In reality, most controls are dependent on a single system or person and could all be compromised from a single failure. A definition of a ‘bow-tie’ control is required whereby it must be independent from other controls. Improving the bow-tie analysis process will assist operators in developing meaningful and ‘operational’ bow-tie diagrams to support risk management systems and practices.

Apr 16, 2024

Determining the environmental consequences of green field projects is becoming an increasingly important component of new projects. Feasibility studies are regarded by potential investors as incomplete if a comprehensive Environmental Impact Assessment (EIA) has not been completed. These EIAÆs need to meet various local and international requirements in order to achieve bankability. Heavy mineral mining projects are often located in ecological sensitive coastal zones, and bring with them a suite of social impacts in the mainly developing countries within which they are usually located. This paper draws on experience gained in undertaking EIAÆs for heavy mineral mining projects in Kenya, Mozambique and South Africa, and uses these case studies to identify potential pitfalls. Important lessons include the need to initiate the EIA process as early as possible in the project, in order to develop management systems to mitigate the environmental impacts of exploration. Close and on-going consultation with affected communities is also seen to be critical to the success of the EIA. Proactive participation on the part of the environmental consultants with the project team and all interested and affected parties (IAPs) is important. An EIA commissioned later in project planning makes it difficult for the EIA to contribute in a positive manner to the project. Early engagement with environmental consultants allows the environmental assessment to develop from a report to an actual process, and to become fully integrated with project planning. The proviso is that an initial æfatal flawÆ assessment is required to identify any potential æshow stoppersÆ, in order to meet one of the important objectives of EIA, namely an assessment of whether or not the proposed project is the preferred development intervention in the study area. For more controversial proposals this may require the commissioning of a Strategic Environmental Assessment (SEA), which circumvents some of the limitations of the project level EIA. Whilst confidentiality is a constraint to full disclosure, an open participatory approach to public consultation is essential to add credibility to the EIA process and to gain, at least, the acceptance of the process from the majority of IAPs. Full disclosure is encouraged by organisations such as the International Finance Corporation, who acknowledge that good public consultation costs a lot of money, but bad public consultation costs a lot more! An open approach to disclosure presents understandable difficulties for proponents, as they are required to give up some of their control over the project, and to trust the social scientists engaged in the process. However, independence in the EIA process is critical to its success. This paper will highlight these and other issues by drawing on five case studies to identify lessons learnt, and explore the above themes in more detail.

Jan 1, 2001

Most publicity about the copper industry nowa- days is focused on the adequacy of ore reserves and on excessive mining capacity. These concerns, stemming from public awareness of actual and poten- tial shortages and oversupplies, relate to production rather than consumption. Perhaps the reason for this one-sided view is that copper is thought of as a commodity which is conspicuously traded in world markets, rather than as one of many industrial materials that serve today's rapidly changing tech- nology. Copper differs from other widely traded com- modities in that its real cost of production has pro- gressively increased since World War II. The reasons for the increase are identifiable by analyzing operations in one of the world's large producing centres, the copper province of Arizona. Another respect in which copper differs from some other com- modities is that increases in demand occur less auto- matically in the case of copper than they tend to in commodities whose consumption is more directly related to population growth. The copper industry's current inability to generate and attract needed investment capital is attributable to these differences between copper and other com- modities; it suggests that the concept of copper purely as a commodity is outdated. The key to the problem is better integration between the activities of copper producers and users. Depending on cir- cumstances, integration takes various forms- for example, investment tied to long-term sales con- tracts between producers in developing countries and consumers overseas; common ownership of pro- ducing and manufacturing facilities in industrialized

Jan 1, 1978

By Snowden C. T

B Lens Main is a scheelite orebody with an average dip of approximately 15¦ and thickness ranging from 1.5 to 6.0 m. The orebody is overlain by a banded section of ore and waste which tends to slab off if left unsupported. It was originally planned to mine a large portion of this orebody by room and pillar methods, with existing diesel trackless equipment. This, however, proved unsuitable for a number of reasons and the smaller scale method of slot stoping with hand machines and scrapers was employed. The following major problems were encountered. 1. The method was new to the mine and the work force, and had to be commenced quickly using existing or easily obtainable equipment. This is gradually being overcome by training, modification of procedures and introduction of more suitable equipment. 2. The slabbing from the hanging wall had to be controlled, either by support or by mining this low grade section and accepting the resultant dilution. This has been approached in a number of ways, depending on conditions and the method will have to be further modified as different conditions are encountered in new areas.

Jan 1, 1977

An analysis of pumping figures suggests that there are two distinct styles of water inflow patterns in Zambia's mines. Carbonate hosted orebodies (Kabwe and Nampundwe) display a characteristic seasonal variation in water inflow with peak pumping showing a short time lag with respect to the rainfall pattern. Aquifer characteristics are controlled by secondary, weathering enhanced, near surface phenomena. Non-carbonate hosted orebodies such as those of the Copperbelt (Konkola and Nkana) occur in successions of highly variable lithology and consequently there are stacked aquifers of variable character. Inflow of water does not display seasonal variation. The major factors affecting the amount of inflow are the structural setting, the geometry of the orebody and the local lithostratigraphy. Thus the Konkola orebodies which occur in a saddle shaped open ended basin result in what is probably the wettest mine in the world, pumping some 376,000 cubic metres of water a day.

Jan 1, 1988

By J Välivaara

The mining industry will face numerous challenges over the next 10–15 years as new deposits are likely to be more remote and lower grade and existing deposits will be mined deeper. As a result, mines and mining contractors operating in deep-mine conditions will need to focus on the quality of drilling and blasting to minimise unnecessary waste rock excavation to keep costs at an acceptable level. In addition, increased demand for improved safety and operator ergonomics will set greater demands on original equipment manufacturers of mining equipment. Finally, difficulties finding a skilled and experienced workforce, particularly in remote mine locations, have already negatively impacted mines’ ability to achieve high productivity and low operating costs.This paper introduces techniques and shares practical experiences in increasing productivity and reducing the costs of excavation in underground face drilling. The paper uses Sandvik’s new DD422i automated mining jumbo as an example of the type of equipment needed to deliver the features and corresponding benefits for future mine development. Case studies using this equipment are presented to illustrate the points made in this paper.CITATION:Välivaara, J, 2016. Automated drilling features for improving productivity and reducing costs in underground development, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 723–730 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By Walshe JL, Solomon M

The Emperor vein system lies on the eastern margin of the Tavua volcanic structure. This is of Miocene age and occurs in basalts(the Mba Volcanics) probably underlain at about 2 km by calcite-rich sediments (the Vatukoro Formation). The lodes are generally flatmakes, or steep fault fillings, or complex shatter zones, and consist of quartz and altered wall rock. In areas of open cavities it is possible to establish a paragenesis which involves five quartz stages and two ore mineral stages. The first ore stage contains calaverite, krennerite, sylvanite and native tellurium, the second petzite, hessite and native gold. The quartz stages are thought to have formed slowly (102 years) from boiling solutions of low salinity at temperatures varying with time from about 250¦C to 190¦C. The system was sealed, the temperature gradient near vertical and the mass flux small. The ore mineral stages probably formed relatively rapidly (101years) from boiling solutions at 250¦ to 200¦C when the system was mainly open. Gold deposition was probably largely a result of fall in aH2S due to boiling, the calculated solution concentration falling from a maximum of about 8 ppb at 250¦C to about 8.10-3ppb at 200¦C. Boiling is also probably responsible for an increase in a02 (by loss of H2) and fall in aTe2 (by loss of H2Te). The fluids are thought to have had a large component of meteoric water and to have been heated by plutons in the core of the volcanic structure. Stable isotope data indicate that they derived their carbon from the underlying Vatukoro Formation and their sulphur from sediments. Circulation may have been confined to the outside of the volcanic structure because of the relatively low permeability of the flows, pyroclastics and dykes within it.

Jan 1, 1987

By N Power, R Hassell, E Jones

Wiluna Mining Corporation are progressively re-entering the old Wiluna underground mining complex. The existing underground was abandoned in 2013 by previous owners and left to flood with water levels reaching above the East Pit portal and Happy Jack Pit portal and up to 300 m below surface in the Bulletin underground. Re-entering the mine commenced in 2017 with dewatering of the Bulletin decline. The underground development had been previously supported with friction bolts, with weld mesh in places. Until mid-2021 rehabilitation requirements were based on an external visual inspection of the installed ground support scheme. However, several incidents involving falls of ground due to corroded bolts have occurred during this time, showing that this approach was inadequate. The challenge the operation faced was should the entire decline be rehabilitated, the implication being not only a large rehabilitation cost but also the impact of severe delays to the mining schedule. The question was asked can the operation better understand the level of corrosion damage and potentially optimise rehabilitation requirements. A proposal to use a systematic approach to assess corrosion by environmental condition mapping, visual external corrosion assessment, and internal corrosion assessment via borehole camera inspections was provided and accepted by Wiluna Mining Corporation. The objective of this work was to produce a three-dimensional map showing the degree of corrosion on the reinforcement systems in the capital infrastructure, this would then be used to risk assess and prioritise rehabilitation requirements. This paper summarises the approach, methodology and results that provided the Wiluna mine planning team with information to enable planning of resources and budget to justify priorities of rehabilitation.

Nov 29, 2022

By Campbell R

The use of a 35mm non-metric SLR camera and an analytical plotter to prepare close range photogrammetric (CRP) plans of a quarry and open pit mine face is described. The plans, at scales ranging from 1:5 -1:1 000, were used to measure the orientation of geological structures and failure surfaces in the exposed faces.Details are provided on the equipment used and the field techniques. The method:ò is quick and relatively cheap to perform,ò allows the accurate orientation of specific geological features to be determined,ò provides survey results of suitable accuracy that may be used for detailed geotechnical analyses of pit wall failures,ò shows great potential as a rapid and accurate technique for monitoring changes in pit wall profiles with time.

Jan 1, 1990

By M Grigorescu, J H. Hodgkinson

The expansive, open cut iron-ore mines in Western Australia typically experience few days of rain per annum, often amounting to less than 250 mm. Unlike mines where rainfall is frequent, they may be less prepared for extreme rainfall events. Such events can cause erosion, flooding and sedimentation, drainage alteration, spoil and stock heaps wetting and effect slope stability. Such impacts may threaten personnel safety, infrastructure, and production. The CRATER (‘Climate Related Adaptation from Terrain Evaluation Results’) framework collates and interprets a mine’s pre-existing data and semi-quantitative information to assess vulnerability to, and ultimately plan to avoid or minimise, flood-related hazard to infrastructure, people, downtime, environment and revenue. Outputs assist decision makers to design investment strategies for minimising mining operations’ vulnerability to climate. Previously developed for smaller, wetter mines in Queensland’s coal region, the outputs provide a hot-spot map, fault tree analysis and an assessment of the mine’s capacity to adapt. The multicriteria evaluation (MCE) within a geographic information system (GIS), equally suits iron-ore mines’ siteconditions (elevation, slope, drainage, soil and vegetation) to identify critical inundation areas. Hotspot results provide target zones for in-depth fault-tree analysis that, in turn, present a range of sitespecific adaptation options. Rainfall-intensity and the number of rain days since the 1970s have increased over central and eastern parts of the Pilbara Region. While tropical cyclones may become less frequent, they are projected to increase in intensity. Although some parts of the Hamersley Ranges receive more than 500 mm per annum, rainfall in the Pilbara is generally very low. Therefore, experience of the impacts of extreme rainfall events in the constantly changing topography of Western Australia’s iron ore region may be sparse. Minimising potential effects can be proactively assisted using CRATER.

Nov 8, 2021

By A J. Daniels

Macraes Mine is a large-scale open-cut and underground gold mine located in Central Otago, on the South Island of New Zealand. This paper presents the role of geological mapping in the grade control process at Macraes Open Pit as a case study, and demonstrates how systematic geological mapping can add significant value to the mining cycle. Geological mapping has proved to be a valuable foundation for orebody interpretation and analysis.Practical applications and lessons learnt are summarised, including predictive control of the orebody, improvement of geotechnical modelling, and identification of further exploration targets.

Aug 22, 2011

This paper addresses the role of mine geology in mining geotechnics. The role is assessed and discussed in terms of five main elements; geotechnical complexity, geological complexity, mine scale, percentage sampling and geological uncertainty. Lastly, the overall objectives and mine geology requirements are listed in terms of the various mine development stages; exploration, feasibility-design and operating.

Jan 1, 1993

The establishment of vegetation onto open cut mine spoil is dependant on the nature of the soil and rock strata of the overburden. Experience has shown that in the Bowen Basin of Central Queensland the nature of the minespoil changes considerably as subsequent and deeper mining strips intercept changing rock strata. The different mixes of strata at the surface of reshaped spoilpiles can produce variable response in the sown vegetation cover. It is usual that land features of mine sites are known in detail and are depicted on mine or locality maps. Subsurface strata and lithology descriptions are available and are used for planning of open cut mining operations. Surface and subsurface data can also be used to estimate the intrinsic nature of overburden through the use of fence diagrams. Lithology at points along a mined strip can be obtained and used to describe overburden. Indications are that correlations exist between salinity of overburden components and the response of vegetation. The developed procedure thus becomes a useful tool for the prediction of revegetation Practices.

Jan 1, 1987

By A Harburg, A Dendys, G Green

Dugald River Mine (DRM) is located approximately 85 km north-east of Mount Isa, and 65 km northwest of Cloncurry, in the north-west Queensland Minerals Province of Australia. DRM is an underground operation and includes an above ground processing area, a 200 ha tailings facility, two waste rock dumps and associated infrastructure. The mining method is conventional underground longhole open stoping and downhole benching of a lead/zinc deposit within a black slate environment. The deposit is estimated to contain ~53 Mt of zinc and lead, which will be mined over a 30-year period. During operations, waste rock is segregated into either Potentially Acid Forming (PAF) or Non-Acid Forming (NAF) based primarily on the sulfide concentration of the rock. In particular, the NAF waste rock is an asset and is used for various small construction projects during operation; however, its primary use is for rehabilitation work at closure. Since beginning operations in 2017, DRM has generated more NAF than was originally anticipated. Whilst this is an excellent asset to DRM, it did pose a logistical problem of where to store the additional NAF for the life-of-mine and how to manage the run-off. DRM experiences distinct wet and dry seasons with hot conditions and periods of rainfall between November to April, and relatively dry and mild conditions between May to October. Majority of rainfall is received between January and February with an annual average rainfall of 501.1 mm. Short and intense rainfall events are common. DRM’s above ground infrastructure is land-locked between two large ephemeral watercourses, making the significant expansion of any assets challenging from a permitting/regulation and cost perspective. MMG is also a member of the International Council on Mining and Metals (ICMM) and is committed to adapting to a changing climate through operations and closure. Following extensive studies DRM opted to store the additional NAF material into the adjoining NAF Dam and concurrently upgrade a previously minor sediment basin into a highly engineered sediment basin which relies on automatic flocculant dosing to meet the required discharge quality limits. This basin is climate-resilient in that the dosing system can be adjusted to counter high intensity extended rainfall events which produce highly variable inflow water quality. This abstract broadly describes how DRM designed and implemented an engineering innovation to enable the site to meet the changing climatic challenges. The abstract then describes the process to design the sediment basin and how the dosing rate was established and validated. Finally, the abstract comments on the effectiveness of the sediment basin and how it has revolutionised DRM’s approach to water treatment and management; all whilst minimising the disturbance footprint of the operation

Aug 2, 2023

By DAVID C LAURENCE

The richer, shallower sapphire deposits of the New England region of New South Wales which have been traditionally mined by the small miner are almost worked out. Larger mining and exploration companies are replacing the small miner and exploring for the primary source of sapphire or lower grade alluvial deposits.Although in recent years considerable exploration effort has been directed at locating the primary source, commercial exploitation of sapphire is still restricted to the working of alluvial deposits.If the Australian industry is to compete against Asian and African producers it must use cost effective exploration, mining, processing and marketing methods.

Jan 1, 1990

By R Bourcier, T Rafferty

Following an underground coal mine explosion, it is important that ventilation is quickly restored to ventilate the mine and affect a mine rescue. To achieve this, surface ventilation fans must be suitably protected from explosion damage, but still able to be quickly restored.A review of all Australian coal mine regulations was carried out, revealing that Australia has no prescriptive regulations that specify the design of explosion relief panels and the protection of ventilation fans in the event of an underground explosion.To better define the level of protection required, this paper reviews and extracts details from relevant major international regulations and standards on the subject.A suitable design methodology for the protection of ventilation fans is presented that could be applied in Australia, using a combination of explosion relief panels, appropriate isolation of the fan, and ventilation shaft/mine design.CITATION:Rafferty, T and Bourcier, R, 2013. The protection of surface ventilation fan installations from underground explosions, in Proceedings The Australian Mine Ventilation Conference , pp 169-173 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 1, 2013