Search Documents

By D J. Robinson, L L. Kuhar

In-situ recovery (ISR) is accepted and applied across many geographies, and approximately 50% of the world’s uranium is currently extracted by using an ISR method (World Nuclear Association, 2014). The low environmental impact, the elimination of risk for mine workers and the fact that all of the lowest-cost producers of uranium use an ISR approach should raise interest from traditional miners (IAEA, 2014). However, the broader application of ISR to other commodities and mineral systems remains limited. A number of demonstration (experimental) copper projects have been undertaken (Sinclair and Thompson, 2015) with a few copper projects in Arizona being close to demonstration (Florence, 2018 and Gunnison, 2018). Evidence of very few economically operating ISR copper projects can be found (for example, the Russian, Uralgidromed OAO, built by the Russian Copper Company in 2005 and operated as an ISR facility from the Gumeshevskoye deposit (Russia Mining, 2018). A number of gold deposits, particularly paleochannel deposits, have also been considered for ISR, but, to the best of our knowledge, only limited demonstration and no commercial operations have been established, yet (Kuhar et al, 2018 and references therein).CITATION:Robinson, D J and Kuhar, L L, 2018. Extending mine life through application of an in situ recovery approach, in Proceedings Life-of-Mine 2018, pp 56–57 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 25, 2018

By Wu Y. H, Lu J. P

Slope stability has now become a practical tool in the design and oper- ation of open pits. The stability of rock slope depends on many factors, including not only structural geology, the existence of weak layers, ground- water, blasting and weathering, but also the virgin stress field. This paper presents an application of a numerical method to investigate the effect of the virgin stress on slope stability. The finite element method is employed to simulate the excavation of open pits. Redistributed stress fields in the slope of open pit are computed for several different virgin stress fields. Based on the redistributed stress fields, the shear force which tends to produce sliding of a rock mass and the frictional resistance to sliding are evaluated. The possibility of potential failure is assessed by the limit equilibrium method. The combination of the finite element method with the equilibrium method provides a powerful analytical tool for slope stability. The significant effect of virgin stress on the stability of slopes is shown by studying a typical case.

Jan 1, 1989

By G Capes

A novel open stope design approach is presented that delivered improved performance in a mining area with poor ground conditions at the Olympic Dam mine. During 2019, a large open stope had an unplanned caving event resulting in the inability to extract the planned tonnes and subsequent sterilisation of nearby stopes. A design limitation was the lack of data and understanding around the alteration domain extents, the rock mass strength controls and limits, the failure modes controlling stope stability in the local area, and the use of conventional stope shapes. From the available data and failure observations, it was inferred that the dominant caving failure mode resulted from a blocky rock mass impacted by structure and alteration causing an unravelling failure mechanism. Numerical and empirical analyses were conducted to test this hypothesis and establish strength limits for design. The strength limits for the design were then used to provide a range of outcomes from which future stope design shapes such as chamfered backs could be selected. Three alternate chamfered geometries were selected to trial the innovative designs. The application of this methodology in 2020 resulted in overbreak reduction from >100 per cent in the initial caved stope to

Mar 29, 2023

By T J. Beardsmore, N Wyche, D Flint, T J. Griffin

Western Australia (WA) is currently the world’s largest iron ore producer, and mining of its huge reserves and resources of iron ore has become a critical part of the state’s economy and regional development. Iron ore exports from WA have reached 760 Mt/a, corresponding to shipping more than one Mt per turn-of-the-tide from the state’s ports. The iron ore sector dominates all commodities produced in WA, and in 2016 accounted for 77 per cent of the state’s royalty receipts, 56 per cent of mineral and petroleum exports (by value) and 50 per cent of mining industry employment. Expenditure on exploration for iron ore (including that for resource estimation and conversion to ore reserves) has declined markedly, from its record peak of $1100 M in 2012 to $280 M in 2016, placing it second after gold. Foreign investment has been a key element underpinning development of the iron ore industry from the 1960s until today, and will likely continue to be so into the future.CITATION:Flint, D, Wyche, N, Beardsmore, T J and Griffin, T J, 2017. The importance of iron ore to Western Australia’s economy, in Proceedings Iron Ore 2017, pp 7–12 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

By Tilley H. L

The 90 m deep Yallourn Open Cut brown coal mine in the Latrobe Valley, Victoria is developing into an area close to a reverse fault. A major batter stabilisation program, matched to ongoing operations, has com- menced to maximise coal recovery where the fault is within 100 m of the Open Cut. The various mine development options considered during the planning stages are outlined. These options were formulated in a back- ground of geotechnical constraints and the need to maintain continuous and reliable coal supply at a time when a new coal field would be developed. The geotechnical investigations and analysis procedures under- taken to determine stability of the batters during their excavation are presented. The geotechnical constraints on the mine design and opera- tions required to ensure safe working conditions are detailed. Current operational and batter stability conditions are considered satisfactory.

Jan 1, 1989

By Hyslop W

It is shown that coke has a major influence on the pattern of operation and on the aerodynamics of the blast furnace and that the physical and chemical characteristics of coke, at each stage in the furnace, determine its ability to satisfy requirements for iron production and coke economy. Analysis of coke sampled from operating furnaces is compared with furnace behaviour. The available data suggests the importance of segregation, strength, size change and chemical degradation of coke on furnace performance. Correlations are presented for coke breakdown ratio as a function of coke rate and hearth diameter which shows that breakdown increases with hearth diameter and with decreasing coke rate. It is also shown that the Micum tests do not reflect the coke strength in a predictable way and that solution reactions appear to play an important role in giving rise to a pitting effect on the cell walls of the coke with the resultant deterioration in coke properties. The catalytic effect of activating substances, such as alkalis, is noted and results are presented which show the effect of carbon solution on the coke strength. The importance of coke in the stack and in the bosh is discussed and flooding results are presented for BSC furnaces which show the probable driving limits for the furnaces considered. It is also shown that coke sampled from different tuyeres in a furnace gives quite different flooding limits. Other applications of the coke test work at BSC are also noted and the relevant objectives listed.

Jan 1, 1975

A co-operative research project, combining Commonwealth Scientific and Industrial Research Organisation (CSIRO) research scientists findings and company iron ore geologists' expertise, resulted in new concepts about the origins, distribution and complexitie of iron ores and their parent rocks (banded iron-formation or BIF) in the Hamersley Iron Province of Western Australia. Understanding these problems was important to the efficiency of exploration, development and ultimate mining of iron ores. This genetic model, based on a detailed mineralogic background, was modified by Mt Newman geologists to obtain a user oriented classification for practical application in the field.The proposed Pilbara Iron Ore Classification (PIOC) gives iron ore geologists a basis from which to understand, identify and record the various mineralogic and physical characteristics of the many genetically different ore types occurring within and between orebodies in the Pilbara. More definitive quality control over ore products can be achieved based on the detailed understanding of ore types which the PIOC allows, compared to current classifications which deal only with the physical nature of ores. Of equal importance, the classification remains sufficiently simple to enable owners, operators and buyers to achieve a basic appreciation of ore type variations.With little modification, it is believed the classification has applications beyond the Pilbara, to iron ore worldwide.

Jan 1, 1984

The evolution of Hall process alumina reduction technology is des- cribed with particular attention to the pot lines. Future directions of tech- nological change are considered. It is predicted that the Hall process will continue to be the avenue for aluminium production for some time to come.

Jan 1, 1982

By M E. Karmis

Traditional coal mining planning seldom considers key æsustainability factorsÆ such as: societal impacts in the area; jobs (both created and lost); dislocation of towns and residences; impact on neighbouring communities and individuals; infrastructure concerns; post-mining land use (except when limited by law or other factors); habitat disruption and reconstruction; long-term economic impacts in the community; and net long-term community benefit. This paper presents a systems engineering approach based on the premise that systems can only be optimised if all factors are considered at one time. In theory, coal mine designs can be optimised for return on investment, environmental protection and sustainability. Using this approach, the permitting process may be quicker and less costly, relationships with neighbours, communities, environmental groups may be improved, the mining industry may be seen as a positive for the short-term and long-term and the mining industry may increase profits. This paper discusses geographic information system (GIS) tools that may be used to incorporate ecological and other sustainable development concerns into models of coal mine sustainability performance. Along with coal production cost and value information obtained from past and present coal mining operations, GIS data are used to develop mathematical cost and equation models. By analysis of on-the-ground data, the parameters to be included in these models are identified, the relationships between these parameters quantified and the models developed. The paper also discusses the next phases of the work to be completed once the data is obtained and the models are adjusted and validated. At that time, site-specific information will be input into the models and the approach to mining a particular property evaluated and optimised for financial rate-of-return and other desired outcomes, such as preservation or enhancement of sustainability values. Finally, the paper will examine how this approach can be combined with traditional mining engineering considerations in order to develop an optimised mine plan for a specific mining property.

Jan 1, 2009

By D Oliveira

The use of an equivalent continuum for a rock mass is not always suitable for situations where the failure is structurally controlled by discontinuities as in the case of wedges in the tunnel roof. In these instances, discontinuum approaches are usually preferred. Rock joints that are filled with soft infill are likely to be the weakest planes in a rock mass, having a dominant influence on its overall shear behaviour. In this case, the joint material model adopted for the discontinuities should be able to describe important mechanisms, such as asperity sliding and shearing, post-peak behaviour, asperity deformation, and the effect of the soft infilling. The latest version of a soil-infilled joint model is discussed here. It describes more comprehensively than previous models the occurrence of dilation and compression with lateral displacements, and also represents the hardening mechanism related to asperity interference as observed in the laboratory that cannot be readily captured by the existing joint models. An analytical approach for the analysis of rock wedges structurally controlled by soil infilled joints is presented.The analytical approach presented in this paper for assessment of symmetric rock wedges in the roof of a tunnel demonstrates, that the peak shear strength of the joint may not be fully mobilised before detachment of the wedge. The analysis verifi ed that an overestimation of the factor of safety may be observed when an elastic-perfectly-plastic joint model was assumed, whereas the computed maximum factor of safety was considerably less when adopting an appropriate soil-infilled joint model.

Mar 8, 2011

By Xaykhamphoune, Ward B

Draglines have been used exclusively for primary overburden stripping at the German Creek Mine complex in central Queensland, where coal has been extracted from a series of ten open cut pits working seams of the German Creek Coal Measures. Due to the dip of the seams, most of the pits have now reached the limit of current economic viability and the emphasis has switched to underground extraction using longwall methods and to a new area of open cut reserves in the nearby Rangal Coal Measures at German Creek East. This area is characterised by weak Tertiary overburden, relatively steep dips and low strength intraformational shear planes at the top and bottom of the coal.The first pit, with a maximum depth to coal of 15 m at the low wall, avoided any major slope failure through use of scrapers to excavate the boxcut and dump the spoil away from the low wall. However, this method was not considered economically viable for the second pit where low wall depths reached 44 m. Following geotechnical investigations the boxcut was divided into a number of zones depending on depth of cover, dip and thickness of Tertiary clay. Slope stability was assessed for each zone using several analytical techniques to ensure that dragline mining would be acceptable. Slope design parameters incorporating various stabilisation techniques, notably an updip trench backfilled with competent spoil to form a low wall buttress prior to excavation of the boxcut panel, were successfully integrated into the mine plan after careful consideration of the complex scheduling to minimise rehandle.

Jan 1, 1992

Western Australian tin deposits are similar to those of other Precam- brian terrains in that they are mainly associated with rare-metal pegmatites, in which cassiterite is found with minerals containing any or all of the elements Ta, Nb, Be, Li, Cs, Rb and the rare earths.. They differ from Phanerozoic deposits where cassiterite occurs in quartz veins, greisens, dis- seminations in granite or sulphide lodes, and is associated with minerals containing W, Mo, Bi, Sb, As, Ag, or Cu. The main tin production in Western Australia has come from the Pilbara Block where the more important tin- bearing pegmatites are related to a younger granite phase, and from Green- bushes where large albite pegmatites intrude ?Proterozoic metamorphic rocks. The more important tin deposits in the Pilbara Block, and those in the Halls Creek and Murchison Provinces, are related to granites which are richer in Si and K and poorer in Ca, Mg, Fe and Ti than 'average granite'. The tin granites tend to have higher than average contents of Sn, Rb and Li.

Jan 1, 1973

By Smith J. W, Wilkins R. W T

This paper is a preliminary report of research on the Mount Morgan gold-copper deposit being done at the Division of Mineralogy, CSIRO. Fluid inclusion and sulphur isotope measurements were made on a suite of 11 samples collected by the staff of Geopeko Ltd. This suite contained representatives of the main ore and rock types of the deposit. Homogenization temperatures of fluid inclusions measured on quartz from 8 of the 11 samples, ranged from 172¦C to 276¦C and to this must be added a pressure correction (in this case, up to 50¦C) to obtain the formation temperature of the mineral. Sulphur isotope measurements were made on 34 sulphides from 8 of the 11 samples. The 6S values form a well defined group ranging from -0.5%oto +3.6%owith a mean of +2.4%c. Although the preliminary data do not indicate unequivocally the origin of the deposit they do impose restraints on the wide ranging suggestions that have been put forward. This work is complementary to the paper of Dr G. Gibbons who has described other mineralogical aspects of the Mount Morgan deposit, based on a more extensive suite of Samples.

Jan 1, 1974

By V Yadi

Geostatistics has been widely used for more than four decades as a powerful tool in ore resource/reserve estimates and grade control. This method has gradually replaced the conventional method such as polygon and cross-section for grade estimation by more mathematical techniques such as kriging. The advances in geostatistical understanding and the availability of appropriate software packages have given much more contribution in speed and high accuracy during production. However, in many cases, these techniques are sometime applied without support with a good thorough understanding of the geological controls on metal distribution. To produce the result close to actual, the geological control in interpretation and appropriate geostatistical task is a must. Geological logging was described in the core must be consistent with the level plan produced by commercial modelling software used as a guide for grade control during production. Experience gained through evaluation of the Central I deposit resulted that the most effective systems continue to be based on geostatistical methods of resource estimation. Computer applications modelling software packages are necessarily as the core of an efficient in undertaking these assignments. They contribute to make a valued to data management and are becoming increasingly effective during processing. The latter role is particularly important to check the actual versus estimated values where will significantly to improve personnel to have a confident with their knowledge combined with experience and complete their jobs satisfy.

Aug 22, 2011

The Skybolt is a new bolt concept, point anchored with resin in large diameter holes of specific sizes 38 mm and 45 mm. The new design achieves the optimum annular spacing required for mixing the resin anchor components which is essential for optimum resin bonding of the bolt to the surrounding rock. This paper explains the load transfer mechanisms between bolt/resin/rock, unique to this bolt concept. It compares the pull-out test results to those of paddle and expansion shell type bolts, and highlights the versatility of Skybolt over existing, currently used, rock support systems and the benefits mine operators can achieve when using the Skybolt.

Jan 1, 1992

By Patridge A. C

Observations of coal stockpiles subject to unusual levels of instability showed that the particular coals exhibited 'gap grading', a relative lack of intermediate size particles. This led to a suggestion that fine coal particles within the pile might have been induced to migrate under the influence of water flow and to concentrate in relatively impervious layers, resulting in local water saturation and reduction of shear strength. To investigate this suggestion, a large test column has been constructed and washed coals with various levels of fines content have been subjected to a downward flow of water. Subsequent examination of the bed of coal within the column confirmed the percolation of fines and their concentration into horizontal layers, and showed the development of zones of saturation above those layers. Shear box tests showed differences in cohesion and internal friction angle between coals with different percentages of fines, supporting the hypothesis that fines percolation may lead to decreased stability.

Jan 1, 1995

The mining industry is quite often faced with declining selling prices for its products in the face of rising prices for the input cost resources that it uses. Blasting is a key activity within the mining system and has a vital role to play within the Mine to MillTM concept. It is therefore important that blasting makes a positive contribution to mine profit and productivity. There are several variables involved in considering the profitability and productivity of blasting. The rock types and structures, the bench height, the blast hole drill rig specifications, hole diameter, spacing and burden, explosive loading and initiation and blast size fragmentation. Productivity accounting is a methodology which is used elsewhere to give additional insights into the productivity and pricing factors that drive the financial performance of a business. Miners know intuitively that productivity and pricing influence costs and profit, but only with productivity accounting can the dollars involved be calculated. Drilling and blasting are part of a chain of unit operations in a mine. For an owner-miner, drilling and blasting would be considered as cost centres and a productivity accounting cost model approach would be relevant. On the other hand a contractor is likely to consider drilling and blasting as a profit centre, in which case a productivity accounting profit model approach would be appropriate. Both of these will be explained. The paper provides a basic outline of deterministic productivity accounting and demonstrates its application to blasting. Drilling and blasting data from a mine was obtained for a two-month period. The change in productivity and prices was calculated to obtain the dollar contributions from them towards the change in cost. It was determined that although there had been productivity dollar gains these were offset by larger pricing dollar losses, the net effect being that total drilling and blasting costs increased. The productivity accounting analysis gives the facts and the mine is in a position to establish priorities based on knowing the dollar contributions of each input used.

Jan 1, 2001

By D Wimpenny

Underground infrastructure is often a critical component of transportation and utility schemes. It is characterised by long design lives with limited access for inspection and maintenance. The exposure environment can be difficult to assess since it will often vary substantially between different locations in the same facility and with time during construction and in service. In addition, the specific demands placed upon underground infrastructure are not well covered by the exposure classes and other guidance given within current codes of practice. When problems occur they can be difficult to rectify and involve significant disruption.Given these substantial risks the prudent designer may adopt a systematic ‘durability planning’ approach which:· defines the environment and principal deterioration mechanisms for the various elements and construction materials,· predicts the design life for alternative durability enhancement options, and· recommends associated measures to be adopted during construction and in service.This paper describes the development of durability planning within Halcrow, giving examples of its use from its first implementation on tunnels under the Suez Canal in 1993 to recent projects in the Middle East and Australia. It seeks to demystify the process, identify shortcomings and speculate on its future development within the civil and mining sectors.

Mar 8, 2011

By Smith Z, Huppert P, Charbucinski J

The paper describes a spectrometric method and apparatus developed for lithology logging in brown coal formations. The nuclear spectromet- ric technique developed is able to delineate coal/sand/clay seams. One requirement was to log inside drilling rods, as well as cased or open holes. The method described is based on combined natural gamma and gamma- gamma techniques using a spectrometric system for signal acquisition and subsequent computer based on-line data analysis and interpretation.

Jan 1, 1989

By M W. A Asad, E Topal, D S. S Sandanayake

Underground mine planning requires an optimal stope layout as a prerequisite for the definition of an optimal production schedule. The procedure to generate an optimal stope layout considers an orebody model and economic parameters as inputs. It evaluates all possible combinations of mining blocks and creates a set of stopes by satisfying the physical mining and geotechnical constraints. Thus, the procedure is computationally complex, and generating a solution to the problem is a challenge. This paper presents an implementation of a new heuristic algorithm that solves the stope layout problem. In two case studies, the algorithm achieves 11.2 per cent and 22.5 per cent superior solutions to the industrially available maximum value neighbourhood approach.CITATION:Sandanayake, D S S, Topal, E and Asad, M W A, 2014. Implementing a new heuristic approach to the underground mine stope layout problem, in Proceedings Orebody Modelling and Strategic Mine Planning Symposium 2014 , pp 243–248 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 24, 2014