Search Documents

By Wilson R. G

The Bulli and Wongawilli Seams, the two principal sources of coking coal for the Port KKembla steelworks of Australian Iron and Steel Pty. Ltd., vary in rank and in type over the Southern and -South Western Coalfields. The Bulli Seam, ranging widely in type, produces coke varying from weak to strong. The Wongawilli Seam, more consistent in type, produces coke of more consistent strength, but considerably less strong than that from the best Bulli Seam coal. Plans of seam variation show the regional trends in rank and type for each sear. The strongest coke is derived from coal containing between 45 and 55 per cent vitrinite, m.m.f. This is obtainable from the Bulli Sean in a zone embracing Bulli and Appin Colleries.

Jan 1, 1969

By Griffith L, Lama RD

West Cliff Colliery mines Bulli Seam occurring at a depth of approximately 480 m. The Seam is intersected by a number of small shear zones and faults. While the faults have caused displacement of the seam, the shear zones are strike-slip structures with small apparent displacement of seam. Outbursts at West Cliff Colliery occur while driving through these shear zones. Few outburst wave occurred where faults have been intersected. In the last 3 years, over one hundred outbursts have occurred at West Cliff Colliery. The size of outbursts varies from a small bump to exceeding 140 tonnes of coal. A number of studies have been undertaken at West Cliff Colliery to control outbursts and predict Outbursts in advance of workings. These include: geological investigations, microseismic techniques, gas adsorption studies and gas drainage. The investigations to date suggest that outbursts of gas at West Cliff Colliery are more a gas phenomenon similar to what occurs in overseas mines. The results of various investigations are reported. West Cliff Colliery is located in the mid- west of the southern coal fields of N.S.W.

Jan 1, 1980

By Elliot B. J

Flash smelting is a complex and capital intensive technology. Although in use for 50 years the technology is still not well understood from a fundamental point of view and thus uncertainty is evident when significant change to the practice is necessitated. The application of effective design and process simulation tools has significant advantages when process change and improvement is required. Mathematical models have been used to simulate the processes occurring in the shafts of copper flash smelters. The present approach to flash furnace modelling differs from earlier work in that the burners were modelled in detail, the output from the burner model becoming the input to the shaft model. This paper serves as an introduction to the modelling process used to analyse the performance and provide a better understanding of the parameters applicable to the flash furnace at the Kalgoorlie Nickel Smelter.

Jan 1, 1992

I congratulate The Australasian Institute of Mining and Metallurgy on its decision to hold its Annual Conference here in Western Australia. Western Australia, with its abundant mineral and energy resources, plays a key role in the Australian mining industry... and Western Australia will continue to figure prominently in this vital industry for many years to come. The success of our gold, iron ore, bauxite, mineral sands and other primary industries has enabled Western Australia to contribute significantly to Australia's export revenue and, therefore, to the nation's economic strength. The State's mineral wealth has also provided the impetus for a recent surge in mining related activity, including a dramatic increase in downstream processing of our raw materials. Billions of dollars worth of new project investment is either committed or awaiting final approval - and most of this new investment is a direct result of a healthy and vibrant mining industry. The North West Shelf Project - which has been providing natural gas for homes and industry in Western Australia since 1984 - has also played a key role in stimulating industrial development. The availability of abundant, competitively-priced gas from the North West Shelf has - along with the availability of other raw materials - made Western Australia a more attractive proposition for industrial investment. The company I represent, Woodside Offshore Petroleum, is operator of the North West Shelf Project on behalf of the Project's six Joint Venture Participants - Woodside Petroleum Ltd, BHP Petroleum (North West Shelf) Pty Ltd, BP Developments Australia Ltd, Chevron Asiatic Limited, Japan Australia LNG (MIMI) Pty Ltd and Shell Development (Australia) Proprietary Limited. The theme for this Annual Conference: "Excellence - the key to the continued success of the Australasian mining industry" is appropriate to the North West Shelf Project. The pursuit of excellence has been a hallmark of the Project. The Joint Venture Participants have been conscious of the need for stringent quality control at all stages of development. Procurement and purchasing policies, for instance, have demanded strict adherence by contractors and suppliers to the highest standards and specifications.

Jan 1, 1989

By D Thornton, R Hodson, D Sprott

Blast fragmentation size distribution and thus blast design have been found to have a direct impact on the load and haul cycle through excavator dig time and bucket payload. Previous studies have demonstrated that by reducing the excavator dig time and increasing bucket payload, significant improvements can be made in both productivity and unit cost. Simulation work reported in the literature indicates that a 20 per cent improvement in dig time may result in only a three per cent improvement in load and haul productivity and unit cost. At the same time, a ten per cent improvement in bucket payload will directly translate to a ten per cent improvement in load and haul productivity and unit cost. Based upon these findings, extensive laboratory and field work have been undertaken in the past to correlate blast fragmentation distribution to bucket payload. In contrast, the literature reports limited studies quantifying the impact of blast fragmentation on excavator dig time. Field work was conducted at Placer Dome Asia PacificÆs Granny Smith Mine (Wallaby Pit) in Western Australia, concentrating on quantifying the impact of blast fragmentation on the dig time of a Liebherr 994 hydraulic excavator (shovel attachment with 14 m3 bucket). Fragmentation was assessed for each truck load of material using the Split Desktop system, while the excavator cycle analysis was conducted manually. Measured fragmentation P80 (fragment size at which 80 per cent of material passes) values ranged from 200 mm to 1200 mm. The field study investigated the impact of various fragmentation parameters (P20, P50, P80, cumulative per cent passing 250 mm size fraction, and uniformity index) on the average and total dig times. The results indicate that the fragmentation P80 provides the best correlation to average dig time (total dig time divided by the number of bucket passes to load a truck). The total dig time was found to be dependant upon the fragmentation P80 and the number of bucket passes to fill a truck. Monte Carlo simulation results, based upon these relationships, indicate a 26 per cent improvement in average dig time and a 12 per cent to 46 per cent improvement in total dig time (bucket passes ranging from 4 to 8), with a change in fragmentation P80 from 600 mm to 200 mm.

Jan 1, 2003

By E ¦iftti, A Koenig

Natural sphalerite associated with copper, silver, lead-zinc, tin and tungsten deposits from various world-famous mineral deposits have been studied by cathodoluminescence (CL), laser ablasion inductively coupled plasma mass spectrometry (LA-ICP-MS), electron probe microanalysis (EPMA) and electron paramagnetic resonance (EPR) to determine the relationship between trace element type and content and the CL properties of sphalerite. In general, sphalerite produces a spectrum of CL colour under electron bombardment that includes deep blue, turquoise, lime green, yellow-orange, orange-red and dull dark red depending on the type and concentration of trace quantities of activator ions. Sphalerite from most deposits shows a bright yellow-orange CL colour with lmax centred at 585 nm due to Mn2+ ion, and the intensity of CL is strongly dependent primarily on Fe2+ concentration. The blue emission band with lmax centred at 470 - 490 nm correlates with Ga and Ag at the Tsumeb, Horn Silver, Balmat and Kankoy mines. Colloform sphalerite from older well-known European lead-zinc deposits and late Cretaceous Kuroko-type VMS deposits of Turkey shows intense yellowish CL colour and their CL spectra are characterised by extremely broad emission bands ranging from 450 to 750 nm. These samples are characterised by low Mn (<10 ppm) and Ag (<1 ppm), and they are enriched in Tl (1 - 30 ppm) and Pb (80 - 1500 ppm). Strong green CL is produced by sphalerite from the Balmat-Edwards district. Amber, lime-green and red-orange sphalerite produced weak orange-red CL at room temperatures, with several emission bands centred at 490, 580, 630, 680, 745, with lmax at 630 nm being the strongest. These emission bands are well correlated with trace quantities of Sn, In, Cu and Mn activators. Sphalerite from the famous Ogdensburg and Franklin mines exhibited brilliant deep blue and orange CL colours and the blue CL may be related to Se. Cathodoluminescence behaviour of sphalerite serves to characterise ore types and help detect technologically important trace elements.

Jan 1, 2008

Mineral resource and ore reserve classification defines the risk associated with quoted resource tonnes and grades, allowing the interested party to make a judgement as to the `worth' of the resource statement. The JORC Code and Guidelines (1992) are now well entrenched as the foundation upon which gold and base metal deposits in particular are publicly reported. There are three categories of resource, namely Measured, Indicated or Inferred reflecting decreasing levels of confidence. The ore reserve, that is the economically mineable part of the resource, is classified as Proven or Probable and can only be drawn from the Measured and Indicated resource categories. As summarised by Stephenson (1995), resource/reserve classification has been an issue ever since the earliest days of mining in Australasia where, like elsewhere in the world, the industry, for a long time, lacked firm reporting guidelines. Those currently adopted in Australasia as the minimum standards for companies reporting to the Australian Stock Exchange (ASX) have been developed and revised since 1972 by The Australasian Institute of Mining and Metallurgy (The AusIMM), the Australian Institute of Geoscientists (AIG) and Australian Mining Industry Council (AMIC). Debate is now underway in terms of adopting an international code. The Code specifically does not attempt to regulate either the classification technique nor the method of estimation of the resource/ore reserve, but rather places the responsibility for this task on a `Competent Person' whose experience will decide the appropriate approach for a given commodity/orebody. The Competent Person must be a Corporate member of either The AusIMM or AIG with five years experience `relevant to the style of mineralisation' under consideration.

Jan 1, 1996

By Wasp E. J

A review is given of recent commercial long distance slurry pipeline systems in- stalled worldwide. The technological advan- ces in slurry engineering and system opera- tion are discussed, together with a brief re- view of the economics of slurry transportation and future trends in the industry.

Jan 1, 1973

By Y T. J Kwong

With the recent emphasis worldwide on environmental protection and sustainable development, finding an enriched mineral deposit no longer guarantees mining development. Only if the identified resource can be exploited in an environmentally-friendly manner is it possible that a mine may be developed. Designed primarily to aid with exploring for similar deposits of a particular type, traditional genetic ore deposit models tend to ignore the fact that all mineral deposits are characterised by type-specific environmental signatures. In fact, how an ore deposit can be mined, the commodities of interest extracted and the resultant mine wastes managed are all largely dictated by the geology and mineralogy as well as the environmental setting of the deposit. An environmental ore deposit model integrates such related information to identify the environmental challenges associated with mining an ore deposit of a particular type and facilitates the selection a suitable combination of methods to minimise environmental risks and impacts. Given that environmental management consumes a large portion of the budget for a modern mining project, making informed decisions at all stages of mining development can reduce the overall project cost. Through case examples, this paper demonstrates how environmental ore deposit models may be useful in mine permitting, active mining and in site decommissioning. It is only through an innovative and flexible approach that the mining industry can shed its tarnished image and gain the social license to mine.

Aug 22, 2011

Ore deposit modelling is becoming an increasingly accepted tool in mineral exploration. Successful models have already been proposed for several ore deposits of base metals and gold, but tin has so far received comparatively little attention, perhaps because of an excessive preoccupatioi with alluvial operations. This situation is rapidly changing and some of the world's most profitable and newly commissioned tin mines are large, primary tin deposits. Some basic principles of ore deposit modelling are briefly reviewed and the fallacy of an excessive reliance on grade tonnage diagrams based on the tin industry worldwide is discussed. The four proposed models and submodels of large, hard-rock, tin deposits focus on basic concepts such as the spatial relationship with "tin granites", depth of emplacement and the level of erosion. General concepts are drawn. The modelling of large primary tin deposits is reviewed not only in its geological and exploration aspects but also in its mining and economic implications.

Jan 1, 1986

By E Mofya, R Kaunda, P Lever

One of the fundamental requirements for being able to optimise blasting is the ability to predict fragmentation. An accurate blast fragmentation model allows a mine to adjust the fragmentation size for different downstream processes (mill processing versus leach, for instance), and to make real time adjustments in blasting parameters to account for changes in rock mass characteristics (hardness, fracture density, fracture orientation, etc). A number of blast fragmentation models have been developed in the past 40 years such as the Kuz-Ram model (Cunningham, 1983). Fragmentation models have a limited usefulness at the present time because:The input parameters are not the most useful for the engineer to determine and data for these parameters are not available throughout the rock mass. Even if the input parameters are known, the models still do not consistently predict the correct fragmentation. This is because the models capture some but not all of the important rock and blast phenomena. The models do not allow for ætuningÆ at a specific mine site. This paper describes studies that are being conducted to improve blast fragmentation models. The Split image processing software is used for these studies (Kemeny, 1994; Kemeny et al, 1999).

Jan 1, 2001

By D Macfarlane, T McMorran

  This paper describes the design and construction of the upper section of the Pike River Mine Access Road. The road extends 11 km from Logburn Road alongside Big River on the West Coast of the South Island of New Zealand up Pike Stream to the new mine portal on White Knight Stream (Figure 1). This new road starts on alluvial terraces, then partially follows an old logging road before entering virgin bush and traversing the true left bank of a steep sided gorge on Pike Stream some 50 - 100 m above the stream before dropping down to the mine entrance. Its development has been an extended process from route selection, consenting through to design and construction.   The paper focuses on the 1 km section of road between the Amenities Area (Figure 1) and the portal. This section of road is a steep section through the gorge, principally on Conservation estate, and has presented the most challenges and required the greatest effort to obtain the regulatory approvals, prepare the design and to construct. This paper outlines the history of the challenges faced and how the road was successfully developed.

Jan 1, 2007

This work was instituted to investigate the microscopic structure of brown coals by means of microtome sections cut from them. It was found to be essential to impregnate the coal with some material prior to cutting, because of its powdery and crumbly nature. Of a number of impregnating materials tried, e.g., glycerine gum, gelatine, by far the most satisfactory was paraffin wax. Samples of brown coals for section cutting must be moist. When obtained, they should be put immediately into air-tight tins, and, if they are not to be used for some time, it is desirable to keep them under water containing a small amount of formalin. If the sample is allowed to dry in air, it becomes too hard to be cut. It cannot be softened again even by prolonged soaking in water.PREPARATION OF COALSmall rectangular, blocks were cut from the sample with a chisel and a strong scalpel. The largest block prepared was 3·2 x 2·5 x 0·6 cm. The faces of the block from which sections were to be cut were approximately levelled before treatment. The block was then painted carefully on all sides with two coats of warm aqueous agar, approximately 2 %. This prevented crumbling and breakage of the block during treatment. When the agar was set, the block was placed in water, and all the air removed with a vacuum pump. The water was replaced first by alcohol, then by chloroform, by the usual step transference of a series of liquids, in each of which the block was placed for 24 hours: Ethanol %, 10, 20, 30, 50, 70, 85, 95, 100 (three changes); Ethanol-chloroform, 3: 1, 1: 1, 1 : 3, chloroform pure (three changes) '. The blocks were then embedded in paraffin of melting point 56-58°C. Fresh...

Jan 1, 1947

By Raymond G. F

Geostatistics - a tool used by geologists and mine planning engineers to estimate grades and rapidly evaluate alternative mining strategies has reached an advanced stage of development for the silver-lead-zinc orebodies at Isa and Hilton Mines. Geostatistics has been used for over a decade in the massive copper orebodies but the stratiform lead-zinc orebodies are much more complex and provided a completely different set of challenges. Recent increases in computer processing speed and power provided by the Integrated Mine Planning System (IMPS) has aided the development of the geostatistics package. Also the formation of a project team and the subsequent in-house development which has drawn together the expertise of geologists, engineers and system analysts has contributed significantly to the success of the project.The most important feature of any approach to modelling the lead-zinc orebodies is that the kriging search must consider estimate and sample points according to their positions relative to bedding surfaces. By transforming co-ordinates as perpendicular offsets from a plane representing the local strike and dip, it is possible to elongate the ellipsoidal influence to parallel bedding. By interactively modelling surfaces using CAD facilities and then specifying these surfaces as 'hard' or 'soft' boundaries, the geologist has complete control over the kriging process.

Jan 1, 1993

By D P. Obeng, L Reemeyer, R Holmes

The Zinifex Century Mine employs a large number of Detritor mills for fine and ultra-fine grinding to liberate silica and sphalerite at 80 per cent passing 7.5 microns before final zinc flotation. A joint project between CSIRO Minerals and the Zinifex Century Mine was carried out to evaluate the Detritor mill performance. Plant surveys were conducted around the Detritors in conjunction with laboratory tests. The survey data showed that the Detritors in the ultra-fine milling circuit performed well. They reduced a feed F80 sizing of 46 microns to a product P80 sizing of 7.5 microns at a gross energy consumption of 37.2 kWh/t. Scale-up of ultra-fine milling Detritors was studied using a 0.55 kW laboratory batch unit and a 355 kW full-scale Detritor by processing Century zinc concentrate with 1 mm sand media. The results indicated that the 0.55 kW laboratory mill underestimated the energy consumption of the full-scale Detritor by about 20 per cent for a product P80 of seven microns. The performances of a horizontal IsaMill and a vertical Detritor were compared as ultra-fine milling devices for processing Century zinc concentrate. The experimental data demonstrated that, when using the same grinding media, the energy efficiency of the two mills is similar despite the difference in mill designs. The Detritors used for regrind duty at the Century Mine performed poorly when processing feed at 80 per cent passing 88 micron. The energy consumption was high and the product size distribution was broad with particles above 100 microns in the feed unbroken and particles below ten microns overground. A coarser ceramic media of 3 mm was therefore tested in a laboratory Detritor to process the regrind Detritor feed as an alternative to the 1 mm Colorado sand used at the Century Mine. The ceramic media reduced the energy consumption significantly and produced a narrower product size distribution, which is more desirable for the downstream flotation process.

Jan 1, 2007

A contract for three 20 ft diameter vertically mounted axial flow fans of the same aerodynamic design, was placed by Mount ]sa Mines Limited in 1963. The hydraulic blade pitch changing mechanism, the method of blade fabrication, and the roll out centre casings are features of these fans. Protection devices and fan control are designed for unattended operation and remote control. The erection and commissioning of the fans during 1964-65 is described.

Jan 1, 1967

A combination of new radiometric age dates, local field relationships and the regional tectonic history indicate that the low sulphidation, fault breccia-hosted, epithermal gold-silver mineralisation at Umuna is related to continental rifting processes rather than subduction induced deformation and magmatism. K-Ar and Ar-Ar age dating of secondary sericite associated with the gold-silver mineralisation indicates that the alteration crystallised between 4.0 and 3.2 Ma, whereas relative age relationships and SHRIMP II U-Pb dating of the abundant Boiou porphyry intrusions on Misima confirm that the calc-alkaline plutonism is significantly older (8.1 f 0.4 Ma) and related to a different tectonothermal event. The Woodlark Basin sea floor spreading centre occurs to the north of Misima and has continued to propagate westwards, into the continental basement of the Papuan Peninsular, since the end of the Miocene. The westernmost tip of sea floor spreading centre is presently to the east of the D'Entrecasteaux Islands but would have been to the east of Misima roughly 4 Ma. Many of the young tectonothermal features in the D'Entrecasteaux Islands (hydrothermal activity and associated epithermal mineralisation, metamorphic core complex exhumation, detachment faulting, peralkaline volcanism, half graben type basin formation) can be attributed to major extensional deformation ahead of the propagating rift system. Similar tectonothermal features on Misima are temporally associated with the epithermal gold-silver mineralisation at Umuna, suggesting that the D'Entrecasteaux Islands are a modern day tectonic analogue for Misima at the time of precious metal mobility and deposition. The rapid exhumation of high grade metamorphic rocks and localised

Jan 1, 1997

By Hunter GW

This paper gives an account of the filling system at Mount Isa from surface fill production to stope discharge underground. A brief explanation of the surface facility and reticulation is given prior to the discussion on aspects of underground reticulation. These include fill hole types, pipe and breastplate installation, wear characteristics, etc. The different types of fill and their respective applications is mentioned as a prelude to a general overview of the mining considerations associated with fill placement and its role in the long term planning strategy at Isa Mine. Some practical aspects of stope preparation and filling procedures are outlined for the various stoping methods. Finally a brief outline of future fill developments is given.

Jan 1, 1982

By H Kurth

High specification Prompt Gamma Neutron Activation Analysis (PGNAA) has been successfully applied to conveyed flows at iron ore operations since 2002 to representatively measure ore quality for improved quality management and process control. While the PGNAA technique has changed little since that time, significant improvements have been made in measurement capability. Elements previously unable to be measured well or at all using this technique are now measurable and one of these is phosphorus. Aluminium and magnesium are also key elements in addition to calcium and silicon in determining sinter basicity in ironmaking. Other elements measured routinely in iron ores include iron, carbon, potassium, sulfur and manganese. The benefits of representative measurement cannot be overstated as iron ore mining operations in South Africa, Europe, Australia, Asia and the Americas have discovered. The technology is applicable to any conveyed flow where elemental analysis in real time assists with quality management, from raw materials in ironmaking through to scrap steel in steelmaking and coal quality for coke-making. Major benefits are realised when raw material processing is optimised and this often includes diversion of material meeting a required quality so it can bypass unnecessary processing. This includes waste rock which can be diverted from a plant feed stream in 30 sec increments or ore that meets product quality being diverted to bypass beneficiation. Analysers are successfully utilised to identify ore types that assist with upgrade optimisation in jig plants; measuring feed, product and discard flows to also account for metal content. Product flows to stockpiles help manage production flows and stockpile qualities for different products and assist in blending ores into trains or ships to confirm specification compliance. Technologies can be used in magnetite processing but are predominantly used in hematite and goethite ore processing operations. The paper details examples of the above applications at various operational sites providing estimates of economic benefit as well as operational improvements.

Sep 18, 2023

By OÆShea P. J, Dickson T. W

In April 1994 the Victorian Premier announced new State initiatives, collectively termed the Victorian Initiative for Minerals and Petroleum (VIMP), for exploration totalling $16.5 m over three years. The program, initially centred on the northwest of Victoria, the Eastern Highlands and the Otway Basin, is due for completion in June 1997 and has been designed to attract explorers to highly prospective but currently under-explored parts of the State. Major components of the program include acquisition of geophysical data (including airborne magnetics and radiometrics, gravity and seismic data), stratigraphic drilling, geological mapping and mineral resource data compilation. At the completion of the current program, 70 per cent of the State will have been covered by airborne magnetic and radiometric coverage at 400 m line spacing or better (Figure I) while 20 per cent of the State will have been covered by new geological mapping. The completion of database compilations for geochemistry, mine data and exploration licence summaries during the VIMP program is shown in Figure 2. The new airborne geophysical surveys have been flown partly under the VIMP program and partly by AGSO under the National Geoscience Mapping Accord (NGMA). Data from these surveys have been interpreted and incorporated into the geological mapping in order to enhance the quality of map products, especially in areas of Cainozoic cover. The first series 1:250 000 scale geological map coverage of Victoria was completed by the Geological Survey of Victoria (GSV) in 1977, and was based on compilation of historical geological mapping with minor field checking in most cases. The first metric 1:50 000 scale geology maps were also commenced in the 1970s, but were discontinued in the 1980s in favour of 1:100 000 scale map production. Driven by customer survey findings and with the benefit of detailed airborne geophysical data in the 1990s, the GSV reverted to 1:50 000 scale map production in 1995, with 1:10 000 scale maps made in areas of significant gold production. Geological reports still cover standard 1:100 000 scale map areas, but are now accompanied by four 1:50 000 scale maps. These new series 1:50 000 scale geological maps have been supported by comprehensive mine data and exploration licence summary databases in addition to the new geophysics, and benefit from the advances made in structural geological interpretation over the last decade. The new phase of geological mapping in Victoria, commenced under the NGMA in 1990 and accelerated under VIMP in 1994, has been focused in the central Victorian goldfields and eastern Highlands areas of the State (Figure 1). Results to-date have led to a number of major advances in the understanding of the eeoloeical evolution of Victoria.

Jan 1, 1997