Search Documents

By Lee H. G, El-Rahaiby S. K

The literature relating to reduction of sulphides by carbon using lime as sulphur-absorbent is reviewed. A stage-wise thermodynamic model is employed to evaluate the practical feasibility of the direct reduction smelting of galena (PbS) concentrates with a carbon reductant in the presence of lime; a coke-rate of 65 kg/ton Pb is predicted by the model. The experimental data on the reduction of PbS:4CaO:4C mixtures under nitrogen were correlated by means of a finite difference numerical method and the values of the intrinsic rate constant I1 were derived. The results for the uncatalysed reduction are represented satisfactorily with log I1 = 1.247(±0.522) - 5540(±610)T-1.The catalysed PbS:4CaO:4C mixtures contained 2.5 wt% of ternary (K, Li, Na)2CO3 catalyst. For the catalysed reduction it was found that log I1 = 3.981 (±0.301) -7790(±353)T-1, where I1 (in both relations) is expressed in moles.(g.C.)-1.atm-1.s -I. The catalytic enhancement faclor was found to be quite large in the 1068 to 1262°K temperature range investigated here.

Jan 1, 1991

By T Roberts, D Faulkner, G Watt

Traditional mechanised resin rock bolting in hard rock underground mines requires the installation of resin capsules into a pre-drilled hole prior to the rock bolt being spun into a hole to mix the resin and set the bolt in place. In poor rockmass conditions, especially at depth or in highly altered faults and shears, the condition of the holes often deteriorates as the poor ground around it unravels and falls into the hole. This results in partially or fully blocked holes that either damages the resin capsule when they are being inserted into the holes or prevent it entirely until the hole is continuously cleaned of debris. This deterioration of the hole condition, and continuous need to clean and re-drill holes, also increases the diameter of the hole which in turn affects the continuously mechanically coupled anchorage mechanism of the rock bolt to the rockmass as there is simply not enough resin in the hole to fill the annulus between the bolt and the rock. This results in a large increase to critical heading cycle time and, more importantly, results in the rock reinforcement not performing as per design specification and increases the risk of instability. To overcome the quality control issues with resin bolt installation in poor ground, a single pass drill, install, inject and tension self-drilling resin bolt application was designed and implemented for use in such conditions. This system allows the operator to inject a two part polyester resin through a self-drilled hollow bolt to mix and fully encapsulate the rock reinforcement. The self-drilling bolt allows for post injection of the hole after the bolt has been installed into the rock and gives the operator manual or automated control on the amount of resin used in the hole to ensure complete encapsulation and continuously mechanically coupled anchorage to the rock. This allows the reinforcement to work as designed and provide the Geotechnical Engineer extra quality control confidence in these conditions. The implementation of this single pass resin bolting system resulted in significant decreases to the resin bolting cycle time and rock bolt quality control failures. In this paper the design, implementation and embedment into the development cycle will be discussed and the in situ quality control checks used to validate the increase in rock bolt installation quality will be shared. CITATION:Watt, G, Roberts, T and Faulkner, D, 2018. Single pass drill, install and inject self-drilling resin bolt application in poor ground, in Proceedings The Fourth Australasian Ground Control in Mining Conference (AusRock), pp 323–343 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 30, 2018

There is a Chinese saying-may you live in interesting times. Certainly we do tod.a~our mining professions. We are, of course, totally dependent on a' healthy mining industry for the chance to practice our chosen professions, and for our Institute.Let us look at one of the more interesting facts. The mining industry now accounts for some 50 per cent of Australia's exports.This massive earning of foreign exchange is the key to keeping our increasing overseas debt in check. Furthermore, mineral production..including petroleum, saves us a large amount of foreign currency by providing essential minerals, including energy minerals, for local consumption.With such fundamental inputs to our economy, any primary school student, any child in fact, should be able to see that the mining industry and mining professions are very important to our nation. Yet the average citizen is unaware of this simple fact as they enjoy their high standard'of living and think that we are still living in the lucky country.Therefore, it is most interesting to me that the average citizen, and most of our politicians, seem to hold mining and miners in low esteem. I use the term miners to describe all those important people, like us, who work in the mining professions, and are employed by, or are dependent on, the mining industry.So why are we miners in this paradoxical situation of doing wonderful works, being the backbone of the country, and yet being held in low regard by the very community we underwrite.Truly-it is interesting-or did the Chinese mean intriguing?It is indeed paradoxical that we are the rare people who open up the land, borrow small parts of it for a relatively short time to harvest the mineral crops, then return it to the community for other uses; and when we return the land back to the community at large it should be in better shape than when we started. There will be infrastructure - roads, airstrips, supplies of water and power, parks and housing-all left behind after mining.These benefits to the community are ignored while our critics focus on the small scars on the landscape which sometimes cannot be healed at reasonable cost; and yet, if we allow time, nature usually heals the small scars anyway. Look at New Zealand, particularly the Coromandel Peninsula which was intensively mined and logged; now it is covered with secondary growth and stark pine plantations. Remember that mining scars are infinitesimally small when compared to urban sprawl or clearing of land for farming and grazing, or highways, or the area of most national parks.Thus, miners are important citizens economically, and we are the majority of the few who actually practice the principles of multiple land use.What are the consequences of our image? They are serious in that the poor image we seem to project, discourages many people from becoming involved in, or supportive of, our industry. This brings me to my theme for the year: Students, Education and Communication - the Key to our Future.

Jan 1, 1987

Subsurface development requires some geotechnical conditions and challenges. Most of then are related to the compatibility between tunnelling system and surrounded ground conditions, and design criteria. Design criteria usually involve lining pressure and ground control of displacements. In order to fulfil these requirements, geotechnical parameters have to be obtained as well as construction aspects have to be taken into account for predicting the tunnel behaviour. The Brasilia Metro is presented as a case history illustrating the geotechnical conditions and challenges for its implementation. It is 42 km long, including tunnels excavated in collapsible porous soils by the New Austrian Tunnelling Method. The Brasilia porous clay presents some characteristics, which may lead to large deformations due to structural collapse. Empirical methods were calibrated for collapsible porous soils and then applied to predict tunnelling-induced settlements. Settlements due to soil structural collapse modify completely the expected settlement profile, increasing their values from the tunnel crown to the ground surface. Consequently, surface settlement trough volumes were also greater than the ground losses around the tunnel. In this case history, structural collapse of porous soils played an important role and must have been taken into account to predict correctly the settlement trough and profile. Numerical simulation has shown that settlement magnitudes due to structural collapse are strongly dependent on the soil stiffness reduction after collapse and the extent of the collapsible zone.

Jan 1, 1999

Rheology is the science which deals with the deformation and flow of matter. Thus rheology is concerned with the flow of any material. The mining industry is concerned with digging things out of the ground, extracting the good stuff and throwing away the bad stuff. In the upgrading processes associated with mining, ie mineral processing, wet techniques are used where the primary material being handled is a particulate fluid, ie a suspension. After the processing operation, with the concentrates extracted, what is left behind generally is a wet material in suspension form, which may or may not contain reagents harmful to the environment. The amount of waste generated in any of the mining processes is large, in fact, the mining industry is the largest generator of solid waste in Australia. In order to minimise the waste generated within the industry it has become of interest to handle the particulate fluid wastes, or suspensions, at high concentrations, thus removing water and some of the reagents which may be harmful to the environment. The resultant highly concentrated suspension is a non-Newtonian fluid. Rheology deals with the flow of non-Newtonian fluids; therefore a combination of rheological understanding of high density suspensions, in conjunction with an understanding of the environmental problems being faced by the mining industry, can and has led to improved methods of waste disposal in the industry, ie waste minimisation. This paper describes the progress that has been made in the development of dry disposal technology in the mining and minerals industry in Australia.

Jan 1, 1998

By G M. Zhomin, A S. Arkhipin, A Kondratiev

Viscosity of multicomponent slags is one of the crucial physicochemical properties for many industrial processes and technologies. While the viscosity-temperature relationship of completely molten slags can well be described by an Arrhenian-type law, the compositional dependence of viscosity is still not fully understood, especially in compositional regions with the lack of experimental data (eg at the glass-former concentration of 90 molar per cent or higher). In the present work major compositional relationships of the activation energy of viscous flow have been revised for numerous binary and ternary slag systems on the basis of experimental data collected and stored in the viscosity database OxiVis. For example, it has been found that the activation energy relevant to the polymerisation effect in binary systems of the MO-GFO type, where MO is the modifier oxide (ie monovalent K2O, Na2O, Li2O and bivalent CaO, MgO, BaO, MnO, PbO etc) and GFO is the glass-forming oxide (SiO2 or B2O3) is not always proportional to the third power of XGFO (contrary to the Urbain formalism) and can vary significantly dependent on the slag system. Also, the activation energy of the charge compensation effect has been revised for ternary systems of the AO-MO-GFO and AO-MO type, where AO is the amphoteric oxide (Al2O3, Fe2O3 or other). A simple polynomial model has been proposed on the basis of the carried-out analysis for estimation of viscosities of multicomponent slag systems. The model has been optimised against the experimental viscosities in the selected binary, ternary, and higher-order oxide systems and has been shown reasonable agreement with the experimental data.

Aug 21, 2024

By R M. Krek

The haulage system used to convey ore from an underground mine to a surface stockpile at the mine process plant is a vital component of the mine’s overall infrastructure and economic viability. The system selected has a significant impact on the set-up of the mine and the access to the underground mine. In turn, the set-up of the mine and the access to the underground mine have a significant impact on the system.A number of haulage technologies are available to transfer the ore from the underground workings to the surface stockpile, including hoists, conveyors, rail and trucks.This paper focuses on the shaft hoisting and inclined conveyor haulage technologies. These technologies have been used consistently to deliver ore from at depth and/or at high tonnage. Previous reviews of the appropriate vertical haulage systems have nominally been restricted to the respective systems only, with no consideration for any other scope or issues that may affect the selection. The selection of the appropriate vertical haulage system, whether shaft hoisting or inclined conveying, needs to consider numerous key factors.CITATION:Krek, R M and Northcote, A E A, 2014. A holistic viewpoint for selecting the vertical haulage system – shafts and conveyors, in Proceedings 12th AusIMM Underground Operators’ Conference 2014 , pp 289–296 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Mar 24, 2014

By L McCallum, G Dale, B Silverwood, T Roscoe, A Costin

The introduction of Progressive Closure and Rehabilitation Plans (PCRPs) in Queensland from 2019 places greater importance on planning and implementation of mine rehabilitation activities. The progress and outcomes of progressive rehabilitation activities is monitored and reported upon to demonstrate success in achieving progress towards the approved post-mining landform, and to inform corrective action where required. The requirements of PCRPs place additional emphasis on mine sites to quantify the risks of successfully achieving planned outcomes. This is particularly challenging given mined-land rehabilitation is a complex process involving decisions on multiple inter-acting management interventions, climatic conditions and spatially variable site characteristics.

Aug 2, 2023

By G de Jong, W Sunyoto, M Cloos

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. The Ertsberg mining district is a 100 km2 area in the highlands of Papua, Indonesia. The district hosts mineralised and barren, outcropping and hidden porphyry and equigranular intrusions. There are at least six major (100+ m wide) porphyry intrusions identified from surface and underground mapping and drill cores. These are the Grasberg Igneous Complex (GIC), Karume porphyry, Lembah Tembaga porphyry, Ertsberg Stockwork Zone porphyry, Kay intrusion and the Wanagon intrusion. Recent deep drilling adjacent to the GIC identified a new hidden porphyry at depth, the Gajah Tidur (Sleeping Elephant), which extends south-west beneath the Kucing Liar skarn. Other named small porphyry dykes and plugs in the district include the West Grasberg, North Grasberg, Idenberg, South East and Zaagkam intrusions. The largest equigranular intrusion is the multiphase Ertsberg diorite.Igneous activities occurred in a relatively short span (<1 million years) from about 3.4 Ma to 2.7 Ma ago, based on U-Pb zircon dating. The various intrusions in the district related to ore mineralisation are high K and appear to have been derived from the same parental chamber, based on similar whole rock rare earth element patterns. Radiogenic Nd- and Sr-isotopic variations indicate that there were multiple recharge events into the parental chamber.The larger intrusions and all economic mineralisation occur in a 4 km wide zone that parallels the N60W-trending axis of the Yellow Valley Syncline (YVS), one of the large folds generated during collisional tectonism. Intrusion pathways at ~3 Ma were localised into dilatational areas in a late and/or post-collisional NW-trending, left-lateral strike-slip zone with Riedel shear offsets between the major fault zones. An early phase of lower K magmatism produced small intrusions in the south-west limb of the YVS.CITATION:de Jong, G, Sunyoto, W and Cloos, M, 2015. Composition, lithochemistry and radiogenic isotopes of porphyritic and equigranular intrusions in the Ertsberg mining district, Papua, Indonesia, in Proceedings PACRIM 2015 Congress, pp 347–356 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

By A L. de Ambrosis, S J. Clarke, R Bertuzzi, J Redelinghuys

The M2 Upgrade Project involved widening 15 km of the existing M2 Motorway, which is a key route in Sydney’s road network. The Norfolk Twin Tunnels in North Epping convey traffic over a 460 m length of the motorway. The project involved widening the twin tunnels to provide a third lane and breakdown lane in each direction.The widening of the tunnels was fundamentally different to other ‘greenfield’ tunnel projects in that the operation of the tunnel was maintained throughout construction, with motorway traffic permitted close to the excavation faces on a daily basis. The widened works had to integrate with the existing tunnel support, construction details, and mechanical and electrical infrastructure.The existing tunnel afforded the opportunity to review existing ground conditions in the tunnel. Exposures were mapped within the tunnel, and key design parameters were back-analysed from the original monitoring data to provide increased confidence in the assessed impact from the widening works.Traffic capacity of the tunnels was maintained by detailed staging of the works, and included the ability to reopen the tunnels at short notice.A permit to tunnel system was developed to manage the risks associated with re-opening the tunnel to traffic. A comprehensive suite of instrumentation was maintained to provide reliable monitoring data to support this process. Emphasis on the robustness and reliability of tunnel instrumentation provided increased confidence in the adequacy of the tunnel support being installed. The monitoring was routinely compared with design predictions to check the adequacy of the support measures being installed and confirm the design.The approaches and methodologies developed for the widening of the Norfolk Tunnels were effective in maintaining the safe operation of the tunnels throughout the two years of construction, and provide a framework for increasing the capacity of existing tunnel infrastructure in the future.CITATION:Clarke, S J, de Ambrosis, A L, Bertuzzi, R and Redelinghuys, J, 2014. Design and construction for the widening of the M2 Norfolk Twin Tunnels, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 591–602 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

Three key areas of C.I.P. plant design, viz. leach- ing time, adsorption and the gold loading on the carbon, are discussed and illustrated with examples. The need for accurate pilot plant data for use in assessing and optimising design is emphasized. This approach should minimize capital and maximise return on capital. It is demonstrated that, as regards adsorption, economics favours short retention time, high gold loadings and mechanically agitated, draft tube reactors. INTRODUCTION Little attempt appears to have been made in Australia to design the present generation of C.I.P. plants to achieve an economic optimum. Most would, seem to have been based on pre- liminary leaching data, gold extraction and value and rule of thumb which, in general, has led to over design and over capitalisation. An essential step to effective economic design is a comprehensive pilot plant study to establish definitive operating parameters, yields and reagent costs. In most cases the cost of developing this data will be more than offset against capital savings in plant; the operating profit should be increased substantially, and profit is maximised for known

Jan 1, 1982

By P Mugebe, M Yahyaei, M S. Kizil, R Low

This paper seeks to establish an empirical relationship between the impact of mining technological innovation implementation and a company’s market value. The company’s market value is represented by its stock price. In a bid to ascertain the relationship, a stock price prediction model is sought to be established using the firm-specific factors impacted by the implementation of innovative technology. This work is performed under the watch of the prevailing macroeconomic factors. The background anchors in the understanding that the difference between the economic status of a mineral deposit and its uneconomic status lies in the level of mining technological innovation most prevalent at a given time (Hartwick, Olewiler and Preuss, 1986; Wellmer and Scholz, 2017; Wright and Czelusta, 2003). This is derived from productivity improvement, resulting in sustainable profitability due to technological innovation. Unfortunately, there is not an adequately established relationship that links this technological innovation impact to the share price performance of the mineral commodity company.

Sep 1, 2024

INDEX OF CONTENTS.1. Historical.2. Manufacture.3. Heat Treatment.4. Fatigue, Failures.5. Consideration of the Establishment o£ a Central Testing or Proving Station.HISTORICAL.Since the introduction of improved high air pressure drilling machines in the early part of the century, efforts have been made to develop the quality of the rock drill bit, in order to take advantage of the greater increase of power output per unit weight of the machines (1). This resulted in the change from solid to hollow steel in the second decade of the present century (2).As the greatest sufferers from the dread disease of silicosis (3), it seemed appropriate that the South African gold mines should be the first to use hollow drill steel. Since then solid drills have become practically obsolete for mining purposes.Water is used with hollow steel drills not only to keep the cutting end cool, but also to assist in preventing the formation of undue dust during drilling. It is of interest to note, however, that water fed through hollow steel or sprayed into the air is only partially effective in removing fine dust particles a few microns in diameter, which particles are said to be the most potent in producing silicosis (3a).So far as the composition of "straight" carbon steel drills is concerned, a commission appointed by the Johannesburg mines carried out a very exhaustive series of tests on drill steels.These drills were manufactured from steel made by all the standard methods, including Swedish, Bessemer, crucible, openhearth, and, to a limited extent, electric furnace steel. It should be remembered that the commissioners' report was issued in 1913, when hollow drill steel had not yet been introduced. Only solid steel drills were then in use.

Jan 1, 1947

By T Raynlyn, R J. Holmes, J R. Manuel, A Poliakov, L Lu

The prediction of sintering performance of iron ore fines and the possibility of targeted optimisation of specific sinter properties are very important for both the iron ore industry and related research organisations. Physical pilot-scale sinter runs require large amounts of raw materials and are expensive, so it is critical to target large test work programs with many different sintering parameters effectively. To predict values for sintering performance parameters such as tumble index (TI), low temperature reduction disintegration index (RDI) and productivity, a comprehensive database of pilot-scale sintering experimental results has been established and empirical modeling conducted. Similarly to earlier work, physical, chemical and mineralogical characteristics of the iron ores have been considered. However, in contrast to the previous work where only one textural parameter was taken into account, namely the proportion of dense haematite ore texture, the current model includes the abundances of several different textures which were combined into different textural factors corresponding to different sinter properties. Coefficients for the variables within specific regression equations can provide a better understanding of the effect of the variables on the corresponding sintering performance. The modelling results have also been used for predicting the sintering performance of mixtures that were not part of the database used for establishing the models. Comparison of experimental and modeling results for the verification test data is also reported in this paper.

Jan 1, 2009

FOR some time past keen interest has been shown in both America and South Africa in the mining drill-steel problem. This interest has extended to Australian mining fields, and Australian drill users, ever desirous of increasing efficiency, are vigorously attacking the problem. The writer has recently been engaged in the investigation of the problem on two of ,the biggest mining fields in Australia, and has formed very definite conclusions concerning the causes of many drill-steel casualties. He puts these views forward in the hope that they may be of interest to, both drill manufacturers and drill users. The subject is here dealt with mainly from the aspect of the properties of the steel and the modifications of these properties whensubjected to various manipulations. It is generally admitted that the drilling machine has greatly increased in power and efficiency during recent years, and the consequence is that the machine is demanding better service from the steel. This is being impressed on the drill users by an increase in steel casualties. This fact has led many mining people to the view that the machine has developed so rapidly that the steel maker has not been able to keep pace, and that consequently the steel isfailing by fatigue 0:1; so-called crystallization. This view is rather depressing. The writer, on the other hand, is inclined to discountenance fatigue as a serious factor under good normal working conditions where the steel is carefully manufactured and supplied to the user under suitable structural and sound conditions, and has subsequently received kind treatment at the hands of the drill sharpener and the drill user.It is not reasonable to attribute failures to fatigue until it has definitely been proved that the steel is fundamentally sound and is in the best structural condition to resist the stresses it is called upon to withstand, and, this being so, that all fundamental principles of...

Jan 1, 1923

By Romanovsky N. P

The Pacific Mobile Belt (PMB) is characterized by old origin and complex evolution both in time and space. As the global structure, the PMB is a narrow tectonic region dividing two plan-etary hemispheres, viz. the Pacific and IndoAfro-Atlantic ones, the relative shifting of which defines the character of many geodynamic processes in this belt. The PMB features inhomogeneity of structure, special matter composition characteristics, sharply broken-out topography, and intensive fields. Generalized anomalies of the gravitational field closely correspond to the PMB boundaries defined by the real features, i.e. the andesite line and distribution areals of Mesozoic-Cenosoic granitoids. The belt boundary position is controlled also by seismic velocity anomalies at a depth of down to 200 km. The modern PMB deformation is defined by the left-hand equatorial shift and rotation of the Pacific Ocean counterclockwise. This rotation is non-uniform in time and of an oscillating character. The motive forces of the phenomenon are considered.

Jan 1, 1990

By A D. T Goode

Data Metallogenica (DM) is unique as a global mineral sample collection and deposit database with over 70 000 rock samples and a wide range of descriptive, photographic and measurement data. Subscribers have access to approximately four gigabytes of on-line data with many examples included on the public pages. DM commenced its life on the Pacific rim in 1971 and much recent growth has focused on countries of the Pacific margin, particularly Australia, Fiji, Chile, Indonesia and Peru. Approximately 600 separate deposits and mineral occurrences in this region are represented in DM. The sets of rock samples have been photographed at high resolution and included on the web site, together with unpublished descriptions, deposit cross-sections, bibliographies, field and mine photographs, petrology and reflectance mineralogy. Figures and abstracts from PhD theses are a new addition and the donation of proprietary databases by companies and individuals is an encouraging trend. DM increasingly is being viewed as an acceptable and important repository for æfragileÆ and irreplaceable personal and company data, it is also being recognised in its true light as a high level information system, not solely a collection of rock samples. Data Metallogenica is a not-for-profit venture of AMIRA International that requires self-funding from December 2004. Growth and development must be funded entirely out of subscription and sponsorship revenues because no government subsidy is provided. The Pacific rim is in the mainstream of mining and exploration activities worldwide and those involved have much to gain from a dynamically sustaining DM. The home page at www.datametallogenica.com contains much example data and details of subscription and membership rates.

Jan 1, 2004

This is the time of year tor the presidential address, and with the present incumbent engaged in the coal mining industry, it will therefore come as no surprise to you that the theme of my address this evening is concerned with coal.There are other reasons for this apart from my contact with the coal industry. At present, coal is supplying considerable overseas revenue at a time when the remainder of the mining market is in a somewhat depressed state. That times will change goes without saying, if history is to be believed.However, so far so good for coal. My first reaction when The Institute indicated its wish that I be president for 1976 was to become deeply conscious of the honour bestowed on me.On consideration, I realized that very few past presidents have been intimately connected with the coal mining industry to the extent of indulging in it for lengthy periods as a full time occupation or, conversely, a part time interest for a long time. It also appears that not one had started their career in the industry. In my case, 'also, there were 8 very interesting years ,as a gold miner and metallurgist before commencing in coal.It therefore seemed appropriate to endeavour to discover ,why this should be so, as coal mining is now a very important part of a very important industry. What were the reasons why the industry took so long to emerge when there were ample reserves of easily accessible coal?Frankie and Johnnie in their bar room epic of the depression years concluded, and I paraphrase, that "their story held no moral, their story told no tale". If my story has such a message, it could perhapsbe construed as reinforcing the oft-repeated dictums, true or false, that "history repeats itself" or "man never learns".Coal mining is by far our oldest major Australian industry except for agriculture. Its history is almost as old as that of settlement:For various reasons, there has been a glamour associated with metal mining ventures which prob...

Jan 1, 1976

LOCATIONThe property of the Mount Isa Mines Ltd. is situated in Western Queensland, 603 miles by rail west of Townsville, the nearest seaport. All supplies and the bullion are railed between Mt. Isa and Townsville. The climate is semiarid, and operations are conducted throughout the year without difficulty.WATER SUPPLYThe mill make-up water is obtained from the mine, and also from Rifle Creek reservoir, which is situated 20 miles from Mount Isa. The domestic supply of water is obtained from a series of bores on the company's leases.POWER SUPPLYElectric power at 3300 volts, 3-phase, 50 cycles, is supplied from the company's steam power plant, consisting of two units, each unit comprising one Babcock & Wilcox boiler, supplying steam at 300 lb. pressure per sq: in. to one 5000 kW. turbo-alternator. Pulverized coal is used as fuel, and power is being generated at a cost of 0.45d. per kilowatt hour. The coal used is supplied from the State Coal Mine, Bowen, costing 42/- per ton delivered at Mt. Isa.

Jan 1, 1933

By K Muller, T Oosthuizen

Blast exclusion zones are instrumental in protecting equipment and personnel. When there is no constraint in footprint, the exclusion zone can be enormous, practically eliminating the hazard of flyrock. Unfortunately, this may not always be the case and in many circumstances the blast design needs to be altered to suite such scenarios. When a conservative design approach is taken, it could completely eliminate any form of ejection, whether it is from the free face or the bench itself. The degree to which typical flyrock models describe fragment motion through air with ballistic flight equations are not justified when such a high level of control is applied. This paper examines various methods of risk analysis and suggests an approach to be used for controlled blasting.The outcome of principles discussed in this paper can be seen in video form (Mavmedia, 2014).CITATION:Muller, K and Oosthuizen, T, 2015. Should the blast exclusion zone be based on a qualitative or quantitative analysis? A practical implementation conundrum, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 425–428 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015