Search Documents

By A McGann, P J. Coghill, D Miljak

"It is widely accepted that bulk ore sorting could provide a step change in processing of low-grade ores. For this to be achieved a rapid, accurate bulk sensor of grade is required as well as sufficient natural variation of grade in the ore stream. CSIRO trialled a magnetic resonance (MR) sensor capable of measuring chalcopyrite, and by inference total copper grade, on the 1300 t/h Ridgeway portal conveyor. The gauge produced an unprecedented set of data down to a 1 t scale for months at a time. This paper analyses the measured variation and compares it to a simple model derived from the bore core data and mixing within the block cave mine.The model of the small-scale (<1000 t) variation is developed using fractal methods which have successfully been used in the past for copper porphyry deposits showing a power law or near power law distribution of copper grade and vein sizes. These fractal distributions have two features highly favourable for segregating ore, a large proportion of low-grade pods and the large-scale spatial clustering of grade. We show the presence of fractal ordering in bore core data at short range in the Cadia Ridgeway porphyry deposit and measure its persistence in the crushed rock produced by the Ridgeway block cave mine over one month. The model is then extended to demonstrate the effect of varying head grade, mixing and pod (or diversion) weight on bulk sorting efficiency.CITATION:Coghill, P J, Miljak, D, McGann, A, 2016. Modelling Grade Variation in Crushed Ore at Cadia Ridgeway and Its Potential Consequences for Bulk Ore Sorting, in Proceedings The Third AusIMM International Geometallurgy Conference (GeoMet) 2016, pp 77–88 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jun 15, 2016

The character of alluvial gold deposits presents severe difficulties, and sometimes limitations, on the extent to which metallurgical efficiency can be measured. Very little monitoring of metallurgical performance is practised. An indication of performance is often extracted from the comparison of production to the estimate. This is a dubious practice. The recovery efficiency of conventional practices, viz sluices, tables and jigs, falls off sharply below 0.2 mm. Field evaluation procedures tend to simulate these conventional practices. Thus the presence of fine gold may not be detected, particularly if obscured by clay. There is increasing evidence that fine gold could, in places, be present in sufficient concentrations to be economic. Most gold in paleoplacers is finer than 0.1 mm. There are established practices elsewhere in the mineral industry that may physically recover gold down to 5 microns in size and which could find application for fine alluvial gold.

Jan 1, 1984

By Stevak D, Plesingerova B, Ellias K, Tkacova K

This paper presents information on the processing of minerals by decrepitation that can be an integral part of their mineral dressing. In the case of carbonates, processing by decrepitation is a special operation that has its objective as concentration of the oxide. Selective fragmentation of magnesite brought about by decrepitation uses pseudomorphosis which was observed at thermal decomposition of carbonates. By decrepitation of magnesite high-grade MgO concentrates were obtained with MgO contents above 80 per cent. With the sideritic ores a very important phenomenon was observed consisting in the removal of quartz in the fragmented fine-grained product which favourably affect pelletisation of the fines. The selective concentration of the MgO product brought about by thermal decomposition of dolomite accompanied with decrepitation was negligible.

Jan 1, 1993

By P Rubie, J Russell

This paper looks at the past, present and not too distant future of grinding mill relining.Since the adoption of autogenous grinding (AG) mills and semi-autogenous grinding (SAG) mills as the primary ore reducing devices in the comminution circuit, plant shutdown frequency and duration has largely been driven by the liner maintenance requirements of these mills.The past 30 years have seen the introduction of many technologies to reduce relining times and frequencies. Advanced relining systems have been developed which include single and twin Mill Relining Machines, capable of placing large (up to 8000 kg) liners, high energy recoilless THUNDERBOLT Hammers, and high capacity Feed Chute Transporters. Despite these advances, today many of the hazards associated with mill relining remain and reline times still vary considerably between mine sites. A sophisticated discrete event simulation program, designed to analyse the mill relining process, has revealed the dominant influences on reline times of crew performance and of the need for safe access to larger segments of the mill.A new generation of advanced and semi-automated technologies is currently being tested that will address these remaining challenges. These technologies remove people from the hazardous environment inside the mill and will allow techniques used in modern advanced manufacturing to provide a near-future step change in mill relining safety and performance.CITATION:Rubie, P and Russell, J, 2018. 21st century relining – the path to greater mine site profitability, in Proceedings 14th AusIMM Mill Operators' Conference 2018, pp 621–640 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 29, 2018

By B Lumsden

During periods of high metal prices and strong metal demand tailings retreatment can be economic. Most tailings retreatment operations are technically challenging, low margin operations, because the easily recovered mineral has already been removed, therefore, process improvements can potentially yield large economic benefits. The Hellyer tailings dam was owned by Intec Ltd and contained 10.9 million tonnes grading 2.8 per cent zinc, 3.0 per cent lead, 88 g/t of silver, 0.16 per cent copper and 2.6 g/t gold. In November 2006 the Polymetals Group, as operator, restarted the Hellyer plant to retreat these tailings. Within a few months the operation had stabilised and Polymetals was meeting budgeted targets of throughput, metal recovery and concentrate quality. Polymetals and Intec then investigated methods that would improve the metallurgical result for this difficult to treat tailings. Since the tailings are fine-grained with 80 per cent <45 ¦m, magnetic aggregation of the paramagnetic sphalerite was evaluated. Magnetic aggregation of an oxidised tailings feed has not been tested before, nor had the technology been available when Hellyer ore was originally processed. Extensive statistical test work showed magnetic aggregation of the sphalerite fines in the zinc cleaner circuit increased total zinc recovery. The increase in the mean zinc recovery with magnetic conditioning was 3.63 per cent, at a statistical level of confidence of 97.8 per cent, and at the same mean zinc concentrate grade.

Jan 1, 2009

By N L. Turner, D J. Robinson, A J. McFarlane, N M. Chapman, L L. Kuhar, R L. Meakin, R Martin

A number of geometallurgical tests have been developed within the AMIRA P843A Geometallurgical Mapping and Mine Modelling (GeMIII) project, an interdisciplinary collaborative research project involving four research groups and over 20 global mineral companies. Researchers at the Commonwealth Scientific and Industrial Research Organisation (CSIRO) have been focusing on the development of predictive hydrometallurgical indices for the GeMIII project via rapid, small-scale, cost-effective tests and protocols for comparative ranking of attributes relevant to leach performance. One of the focus areas has been the development of a leaching scheme for determination of the mineralogical deportment of copper in a large number of samples for geometallurgical applications.Various leaching schemes have been used over the last 20 years to identify the mineralogical deportment of copper. Typically, weak sulfuric acid and cyanide are used to target copper oxides and æsecondaryÆ copper sulfide minerals, covellite, chalcocite and bornite, respectively. Residual copper is assigned to chalcopyrite and/or bornite. Adaptations of this scheme have included the use of a weak organic acid to target oxides or ferric sulfate to target secondary copper sulfides. Testing of the weak acid/cyanide scheme in the GeMIII project using head and residue QEMSCAN mineralogical data analysed with a statistically reliable comparison method indicated that the inferred mineralogical deportment from various leaches could differ markedly from the theoretical or assumed value. Based on this initial work, test development and leach tests on samples from multiple sites has resulted in the development of a scheme to target copper oxides, chalcocite, covellite, bornite and chalcopyrite. This paper presents results from leach tests conducted on a large sample suite from two pits in a Cu-Au ore deposit with results calibrated using mineral liberation analyser (MLA) mineralogical analysis. This study has assisted in the development of a protocol for determining the mineralogical deportment of copper in a large number of samples for geometallurgical applications.CITATION:Kuhar, L L, McFarlane, A J, Chapman, N M, Meakin, R L, Martin, R, Turner, N L and Robinson, D J, 2013. Calibration and testing of a geometallurgical leaching protocol for determining copper mineralogical deportment, in Proceedings The Second AusIMM International Geometallurgy Conference (GeoMet) 2013 , pp 177-186 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 29, 2013

By I Gipps

A vision of what the future mine involves all aspects of mining, ie orebody access, ore stoping, material transport, processing and waste material disposal. This paper examines one aspect of the future mine: rock extraction, stoping, automated for remote operation, high productivity and low cost. Concepts for the future require a re-think of the mining process and ROES® re-examines how bulk stoping of ore can be undertaken and how this should be redesigned to accommodate the possibilities that exists with remote control and automated operations.ROES® is a new mining system for underground mines and quarries utilising a shaft located close to or within the stope for the ore breakage process. The system is designed to exclude personnel from contact with production drilling, explosive placement and detonation so all of these tasks are remotely controlled or automated. Survey of the shaft, stope back and broken rock within the stope will occur, following each blast, by remote control or automated techniques. The survey will include excavation geometry, rock fragmentation, geotechnical characterisation and estimation of ore grade. Blastholes will be surveyed before placement of explosives and, with the survey data, the optimal explosive placement and blast timing will be determined with the best available information.ROES® is designed for application in open stoping or sublevel caving in disseminated, geologically defined, thick tabular or narrow vein ore bodies. Technologies developed for ROES® will also have potential applications to caving operations, reducing the risk of frozen ore and poor fragmentation. In a typical sublevel open stope application, ROES® will reduce the stope associated development by half and will allow ore to be brought on-stream sooner and at lower cost. Other savings will flow with the centralisation of mining activities and operational data, reduction in mining fleet, reduction in ventilation requirements, improved occupational safety and reduced mine complexity.

Nov 22, 2011

By D Luppnow, H Rourke

Recent disasters such as the failure of the Mount Polley tailings embankment remind us of the risks that tailings facilities pose. It is widely recognised that dam-break assessments are a vital tool in identifying the consequences of the failure of a facility, which in turn can be used to develop emergency action plans. A typical assessment includes an estimation of breach parameters and outflow volume, followed by the preparation of an inundation map to illustrate potential flow extents and downstream impacts. This paper focuses on the estimation of outflow volumes, which is an area that the authors feel can be improved. Presently, many types of analyses assume that the volume of tailings released is only a function of the storage volume and dam height. After a review of several documented tailings failures, it has been found that the extent and depth of the supernatant pond needs to be considered as it is just as important, if not more so, as the storage volume and dam height. Tailings facilities with excess water storage have a higher risk of failure as they are more susceptible to overtopping, piping and liquefaction failures. In addition, they pose greater failure consequences as the saturated conditions will lead to more material being mobilised.This paper has reviewed available information on a number of tailings dam failures and proposes an alternative estimation of potential tailings release volumes as a function of supernatant water stored on the facility for use in dam-break analyses. In a broader sense, the paper seeks to shift the current risk paradigm from tailings dam heights to volumes of water stored and provides a basis for continuing research and discussion.CITATION:Rourke, H and Luppnow, D, 2015. The risks of excess water on tailings facilities and its application to dam-break studies, in Proceedings Tailings and Mine Waste Management for the 21st Century , pp 225–230 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 27, 2015

By J Boshoff

The management and operation of tailings storage facilities (TSFs) are often neglected until the process plant has to shut down as a result of this negligence or as a result of a catastrophic failure as was the case during the recent TSF failure in North America.TSFs are often regarded as non-assets and do not receive the attention they deserve in terms of technical expertise and financial provision. A TSF is not a simple structure but a complex and dynamic structure that changes throughout its operational life. The operational life of a TSF is the period in which there is the greatest opportunity for risks to occur. The failure of a TSF is normally not as a result of a single event but as a result of a consequence of events. These events are often not recognised in time due to a number of factors.Process plants and slurry pumping systems are operated at suboptimal conditions in order to maintain throughput. At the same time, the tailings properties are compromised in terms of slurry density and particle size distribution amongst other things. Tailings deposition cycles and drying cycles are not well understood and the tailings management strategy is not well tuned in terms of maximising consolidation and improving in situ densities. Pond control is also neglected. These are aspects that form the keystone to the effective utilisation of available deposition area as well as the frequency and cost of future embankment raises.Apart from operational issues, forward planning in terms of budget requirements, increases in tailings throughput, embankment raises, pipe replacements, etc are normally put on the back burner. Available deposition space at the time seems to render this planning obsolete.The bottom line is that responsible tailings management and proper forward planning can limit liability and reduce the bottom line in terms of cents per ton if correctly implemented by suitably qualified tailings managers and engineers.The aspects that need to be considered as part of responsible tailings management are highlighted in this paper.CITATION:Boshoff, J, 2015. Responsible tailings management, in Proceedings Tailings and Mine Waste Management for the 21st Century , pp 317–322 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 27, 2015

By Mills KW

Coal mine pillar design formulae available to mine planners are typically based on relationships determined for specific site conditions. Application of these methods is difficult when other factors, relating to mining or geological conditions, not specifically addressed in these relationships are encountered. A review of pillar design methods, coal strength properties and relevant field monitoring of pillar behaviour has shown pillar strength and deformational characteristics are extremely sensitive to in situ behaviour of the rock and other material components that make up the coal pillar system. A method has been developed that has been found to provide excellent correlation between existing field data using the strength and deformational characteristics of materials determined in selected laboratory tests. This method is based on definition of the loading conditions, accurate modelling of the strength, confining conditions and deformation occuring in the roof, floor and coal seam and definition of the in situ strength of coal based on underground monitoring of appropriately sized coal pillar. The design method is considered to provide an accurate and rigorous pillar design method that will give mine planners a more rational mine design capability which is based on the mine geometry and geological setting of the operation. It is envisaged that availability of such a method will allow significant optimisation of pillar layouts and more closely define the geological and mining issues that relate to pillar design optimisation.

Jan 1, 1992

By M Noakes

EcoTechnology refers to a series of potential metallurgical processes for complex ores, concentrates, tailings and slags that are all based on an initial chlorination step at low to moderate temperatures probably in a fluid bed chlorinator (FBC). Examples of the research and development (R&D) results are provided in this paper for a high grade Au/Sb Leach Tailings (EcoGold<sub>®</sub> Process), a very refractory sulphide Au concentrate, a refractory gold calcine tailings, a Cu/Au tailings (EcoCopper<sub>®</sub> Process), bulk polymetallic sulphide concentrates and polymetallic sulphide/oxide complex ores (EcoZinc<sub>®</sub> Process and EcoLead<sub>®</sub> Process). R&D on over thirty different ore types has been conducted at a bench scale as discussed. Latterly a dedicated pilot plant was designed and constructed by EcoTech Mining Pty Ltd (EML) and several of the different feed stock results have been confirmed by pilot plant testing. It is planned to scale up to a commercial demonstration plant. To demonstrate the versatility of EcoTechnology, bench and pilot plant test results on five of the projects are used as case studies as follows: Fosterville ‘leach tailing’, VIC; Wiluna flotation concentrate – BIOX Feed, WA; Wiluna calcine facility tailings, WA; Mt Morgan Cu/Au tailings, QLD; Polymetallic sulphide concentrates from Pegmont Deposit, QLD and Polymetallic sulphide/oxide ores from Commonwealth Mine Project, NSW. CITATION: Noakes, M, 2018. Improved recoveries and environmental outcomes from complex ores utilising EcoTechnology, in Proceedings Complex Orebodies Conference 2018, pp 122–123 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 21, 2018

By M I. Pownceby, A Guiraud, S Purohit

Sticking and breakage of iron ore pellets during high temperature reduction can result in several operational challenges during shaft furnace ironmaking. With the shift to H2-based DRI processes and decreasing iron ore quality, this issue becomes more prominent. It is therefore important to understand how the iron ore chemistry and mineralogy affects the sticking and breakage of pellets inside the shaft furnace. This study provides a review of the mechanisms that lead to sticking and breakage of pellets inside the shaft furnace. The sticking index of pellets is related to the rate of metallic iron production as well as the precipitation morphology of product iron. Sticking of pellets is also enhanced by the formation of low-melting slag phases. The breakage of pellets inside the shaft furnace is often associated with the mechanical load of burden and pellet swelling, which is caused due to iron whisker or protruded iron formation. This paper investigates how the composition of iron ore, particularly the presence of different impurity oxides such as SiO2, Al2O3, MgO, CaO and alkali oxides in the pellets, influences the sticking and swelling indices. The effect of ore mineralogy on these adverse behaviours is also discussed.

Sep 18, 2023

Gold was discovered at Waihi in 1878. In 1987 the modern Martha Mine opened in the middle of the town of Waihi. Newmont Waihi Gold as the current licence holder has been operating the mine since 2000. The current open pit was scheduled to stop production in mid 2006. An underground mine is currently being developed to the east of the town.   In 2001 serious subsidence issues from historical underground mine workings outside the mining licence and the forecast closure of the open pit acted as a catalyst for the development of new communication initiatives.   In this context Newmont Waihi Gold and the Hauraki District Council initiated a community consultation process with the people of Waihi. The Waihi Community Consultation Committee (WCCC) was established in May 2003. After an initial brief to act as a forum for community participation in closure and rehabilitation of the Martha Mine, the group quickly took on a much more proactive role working towards the long-term social, environmental, cultural, economic and spiritual sustainability of Waihi.   In the course of over three years of meetings all groups represented on the committee have presented their views, developed ideas and established an organisational structure to bring those ideas to fruition. The challenge now is to work together to consolidate likely options, seek sources of funding, produce business proposals and implement the plan for the future of Waihi.   This paper backgrounds the experience to date and describes the outcomes of the process. For more detail on process considerations this paper should be read in conjunction with Part C by process facilitators, T Clark and S Stewart. For more detail on progress towards the groupÆs goals and future possibilities, this paper should be read in conjunction with Part B by Vision Waihi Trust CEO, E Morrow.

Jan 1, 2006

By G R. Ballantyne, B Putland, I Lovatt, M Di Trento

The Tropicana Gold Mine, owned by AngloGold Ashanti Australia Ltd (70% owned and managed) and Independence Group NL (30%) is located 330 kilometres east-northeast of Kalgoorlie, Australia, in the newly developed Albany-Fraser Orogen. Following extensive feasibility studies, a high pressure grinding roll (HPGR)-ball milling circuit was selected based on the reduced power requirements and thus reduced operating expenses. The HPGR-ball mill circuit was estimated to require 75% of the energy of a standard semi-autogenous grinding (SAG) mill circuit. Even with an anticipated greater capital cost, the HPGR-ball mill circuit was found to give significantly better financial returns in all cases investigated in the feasibility study. A comparison between the specific energy requirements of the HPGR, crush and SAG based circuits (SABC) from the feasibility work was conducted and the HPGR circuit was found to be considerably more energy efficient. A survey was conducted and the efficiency of the HPGR was similar to both the overall circuit design and the HPGR laboratory results, reflecting the accuracy that is possible for design and operation of HPGR circuits.Between 2015 to 2016, the Tropicana circuit has achieved a 20% increase in throughput from 780 to 930 t/h, and this increase has been maintained in 2017. This improvement can largely be attributed to upgrades to material handling processes, increased HPGR speed and smaller HPGR screen apertures. The result of these changes has been to increase the ball mill capacity by increasing the breakage conducted by the HPGR.CITATION:Ballantyne, G R, Di Trento, M, Lovatt, I and Putland, B, 2017. Recent improvements in the milling circuit at Tropicana mine, in Proceedings MetPlant 2017, pp 73–83 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 11, 2017

By Grossi M, Baiden G

This paper describes a new mine backfill method based on a newly invented binder with several years of test results from laboratory and on- site applications. The new binder has several advantages over traditional Portland and slag cement binders. One tonne of the new binder can replace two to three tonne of Portland cement when used to consolidate backfill and can result in the same compressive strength within seven days. When comparing backfill slurries of the same pulp density, the new binder attains more volume of in-place backfill mass than Portland cement because of the high crystallisation of water, resulting in tightly filled stopes. The crystallisation of the water provides for less or no de- watering in the backfill stope and easier transportation of the backfill slurry. Pastefill performance can be achieved by using pulp densities typical of a hydraulic backfill and the new binder, all the while transporting with the same ease of hydraulic fill.

Jan 1, 1998

By K H. Esbensen

Optimisation of a real-time at-line monitoring system for control of industrial granule coating quality is presented. The system is based on a fluorescence imaging system, because fluorescence originates in the interiors of enzyme granules but is significantly quenched by a polymer coating (which is needed due to environmental precautions). We have developed an image analytical system for direct prediction of coating quality, which is based on application of the Angle Measure Technique (AMT) for image complexity characterisation; AMT is briefly described. The first part of the presentation addresses pixel sampling strategies within a digital industrial image, inherent in application of AMT, in which the unfolded image is regarded as a one-dimensional object in analogy with 1D process sampling in Theory of Sampling (TOS). The effects of random, stratified and systematic pixel selections in the unfolded image are evaluated. Also factors such as the fraction of image pixels and the effects of specific unfolding strategies (there are three principal strategies, termed æchopÆ, æsnakeÆ and æspiralÆ respectively) are investigated. It turns out that unsuspected artifacts are sometimes produced, related to the specifics of the unfolding procedure, which interferes with a straightforward 1D TOS process sampling analogy. These artifacts have a wider interest û among others, for 2D sampling û and therefore receive special attention in this presentation. The optimal pixel selection strategy for the AMT algorithm is found to be systematic or stratified sampling (not surprising according to TOS) of 500+ initiating points, but need to be unfolded in the novel spiral- or snake-wise fashions in order to effectively counteract these artifacts. This also has a general impact on various suggested standard schemes for 2D grid-sampling, among others, from the geoscience realms. The second part of the presentation is directed towards optimal image analytical sampling of a continuous series of fluorescent images (imaging of conveyor belts of æinfinite lengthÆ), ie optimisation of process image sampling. The minimum number of images needed to uphold a sufficiently good on-line estimate of the quality control (QC) parameter in question is found to correspond to the relatively high sampling rate of 15 - 20 per cent, which can be shown to be related to an intrinsic very high measurement error level (25 per cent) of a mandated analytical reference method.

Jan 1, 2005

Woodlawn Mines began underground operations in 1986. At the time of going underground it was envisaged that there would be no 'contract' payment to the underground employees. This was a relatively unique step to make, especially as most major underground mines in Australia relied heavily on the contract system to motivate their workforce. (Obviously with varying degrees of success.) Woodlawn faced the task of motivating their employees through a multi-skilled system with a great emphasis on leadership and a genuine care for their employees. The 'proof of the pudding' is that Woodlawn has not lost any time over industrial issues since beginning underground operations in 1986. To achieve success in any operation the organisation must not only be advanced in its management principles but also be prepared to be innovative in the way it deals with physical problems, ie ground control, equipment selection and maintenance. Difficult ground conditions at Woodlawn have necessitated the deployment of two Cabolt Jumbos and the construction of cost-effective shotcrete systems. The shotcrete system now being built has been tested in a prototype form and is proving to be a safe and simple way to manage weak, low stress friable ground. Although the ground at Woodlawn has low stress component by virtue of the fact the ore can have a density of 4.5dm3, cable dowelling has become a necessity. The two cable dowel jumbos install high quality reinforced cables. The pressure of 'production' means that these machines must be consistently available for use and the training of maintenance personnel and operators ensures that a maximum of cable dowels can be installed over any given time span. In any modem mine ventilation is a primary concern and the major area of concern comes from the vehicles themselves. In our recent replacement for the standard 'Toro' loader, three engine options were considered. A relative newcomer to underground mining was accepted. The Detroit 60 series (DDEC) engine came with a great reputation and has lived up to this. The engine has an electronic management system that reduces particulates to a hardly visible minimum, provides great amounts of engine power and reduces fuel consumption by approximately 45 per cent. The operational benefits of such an engine are worth sharing through this conference.

Jan 1, 1995

A considerable debate has arisen regarding the best route for the beneficiation of iron ore. Supporters of jigging technology claim that although the technology is old, due to recent advances in jig control and a better understanding of the separation processes within jigs, it offers significant advantages over dense medium separation, especially in terms of reduced capital and operating costs and simplicity of design. Supporters of dense medium separation claim that this technology is proven to provide the best possible separation and that the gain in efficiency over the life of the plant, compared to that of a jig, will more than offset any differences in capital or operating costs. The truth is that both viewpoints are valid and that the choice is ultimately determined by specific characteristics of the ore being treated. Factors that need to be taken into account in deciding upon the correct option include the size/density distribution of the ore to be treated, the different size fractions which must be treated (lumpy or fines), differences in yield at grade, plant layout and capital and operating costs. Each of these factors will be discussed in detail and a case study for both lumpy and fines will be presented.

Jan 1, 2007

By C McCamley

"The requisite for maintaining optimal carbon concentration levels in a carbon-in-leach (CIL) circuit is of paramount importance in the prevention of gold losses. The process’s ability to recover gold from the aqueous phase is primarily dependent on the carbon loading profile of the CIL train.Newmont Boddington Gold (NBG) have over 2015 tested the Mintek online carbon concentration wmeter (C2 Meter) suitability for effective carbon concentration measurements in their CIL circuit compared to the standard method where the readings are taken twice a shift by the operations staff. The C2 meter works by passing a 1MHz ultrasonic signal through a slurry containing carbon where there is a relationship between the carbon concentration and the attenuation of that signal.It also highlighted another area where the C2 meter could be implemented at NBG whereby the instrument can be as a cautionary device for carbon losses in place of carbon safety screens.Citation:McCamley, C, 2016. Continuous Carbon Concentration Measurement at Newmont Boddington Gold, in Proceedings 13th AusIMM Mill Operators’ Conference 2016, pp 207–212 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Oct 10, 2016

My topic for today is the Crown Minerals of the future. New work initiatives are underway and the organisational structure is being overhauled. These are not insignificant changes and in this paper briefly summarises these proposals. These new work initiatives and changes to the organisational structure will have implications for the industry as a whole and also for the way individual clients interact with Crown Minerals.

Jan 1, 2003