Search Documents

By AIME

WILLIAM WALLACE MEIN, known to his intimates as "Will" or "Billy", is a mining engineer who has taken the fundamentals of successful mining--operating, engineering, and financial-and applied them to the founding of new industries. Born in Nevada City, Calif., in 1873, Will Mein grew up in an atmosphere of mining, and began to develop his sound judgment in a practical way before starting his formal technical education. As a young man he supplemented his early observations by helping his father, Captain "Tom" Mein, on mining work in California and Alaska. He then went with his father to the Rand, and after a period of milling experience as operator and shift boss he became, in 1894, manager of the chlorination of gold ores at the Robinson mine.

Jan 1, 1947

By Herbert F. Miller

For a long time I have believed that the gas- and brick-costs of open-hearth furnaces using prodncer-gas could be greatly decreased by a change in the design of the port, which would materially reduce the first-cost of the furnace, the rebuilding-cost, and the repair-cost. The defects of the present type of such furnaces, which has clone duty for so many years, may be studied in Fig. 1, in which A A are the two air-uptakes, B is the gas-uptake, and C the end of the gas-port. In the present type of furnace, C is practically 011 the edge of the bath and therefore combustion begins to take place at that point, but has no effect until the gas passes from 5 to 10 ft. into the hearth. As the furnace grows older, C moves back by reason of the burning or falling down of the arch. The furnace reaches its highest efficiency when C has moved a certain distance, but is still near enough to the bath for the overhead layer of air to hold the gas down on the bath, and far enough back to permit combustion to take place at some distance from the bath. This latter fact means that the temperature is sufficient to melt steel at the edge of the port. From this time on, the furnace decreases in efficiency. What is the reason ? As C moves further hack, the gas is released from the gas-port at a point where there is little or no overhead layer of air. The result is that the gas floats along the roof, with the air mostly underneath it. Why the air does not stay over the gas is readily seen in Fig. 1. The lines of draft naturally run parallel to the length of the furnace. The air-uptakes being on the sides and the gas-port in the middle, most of the air will naturally be drawn along the sides of the furnace and the layer of air will be thinnest over the gas, where it is most needed.

Jan 1, 1914

By George A. Roberts, Robert F. Mehl

WHEN austenite first forms from aggregates of cementite and ferrite, it is not homogeneous.1 This inhomogeneity, consisting of both undissolved carbide and carbon concentration gradients, has a profound effect upon the characteristics of the austenite-pearlite reaction. The rate of formation of pearlite is increased by the presence of inhomogeneities2,3 and because of this (when the inhomogeneity is sufficiently pronounced) the hardenability of the steel is reduced,4,5 In addition to this kinetic effect, inhomogeneities will cause the direct formation of spheroidite from austenite at temperatures just below the Ae1.6-11 The present report attempts quantitatively to evaluate the effect of inhomogeneity upon the rate of the austenite-pearlite reaction, presents a method of determining the austenitizing cycle necessary to obtain "practical homogenization," and considers the effect of inhomogeneity on hardenability. EFFECT OF INHOMOGENEITIES ON REACTIONS NEAR Ae1 Few quantitative data are available representing the effect of undissolved carbide or of carbon concentration gradients upon the rate of the austenite-pearlite reaction. In procuring such data it is necessary to separate the effect of undissolved carbide from that of grain size, and this is not an easy task. The solution of carbide is always accompanied by an increase in the grain size, both effects contributing to the retardation of the reaction rate. It has been possible to make this separation and to obtain data that are independent of the grain size by the use of steels that differ only with respect to their tendency toward grain-coarsening. Steels C and D in Table I are such steels. These steels have been studied previously;1,2,12 they differ only with respect to deoxidation practice; C was deoxidized with silicon while D, teemed from a portion of the same heat, was deoxidized with additional quantities of aluminum in the mold. C therefore is what is normally termed a "coarse-grained steel" and D is a "fine-grained steel." These steels can be compared at the same grain size by heating C to a low temperature and heating D to an elevated temperature, producing a structure of austenite plus residual carbide in the former while forming homogeneous austenite in the latter; in such

Jan 1, 1943

By Walter B. M. Davidson

Phosphorus is one of the elements having the widest distribu tion, and phosphoric acid plays an important part in the composition of the crust of the earth. It is allied in various chemical combina- tions with many bases, of which lime, alumina and iron are the most common. It is difficult to state in what chemical combination phosphoric acid predominates in the crust of the earth, for while phosphate of lime, as the mineral which is sought for and found in deposits of economic value is the most familiar, it is probable that the phosphates of alumina and iron are the most usual forms in which phosphoric acid exists in all soils not essentially calcareous. It has been shown by thousands of analyses that all fertile soils contain from a trace to 0.5 per cent. of phosphoric acid. All limestones, dolomites and chalks contain it in proportions which, though usually small, are large enough to make careful analysis necessary in the selection of limestone as flux for iron-smelting. It is generally Trenton limestones that are found best for this purpose, the more recent strata being more phosphatic. In some places phosphoric acid replaces carbonic acid, and the limestone or chalk becomes phos phatic to a large degree, or sometimes pure phosphate of lime. The waters of the ocean, from very early periods, have contained phosphoric acid. Different analyses show varying contents; it is asserted that some portions of the Gulf Stream are more phos phatic than the surrounding waters of the Atlantic. Many springs, usually from limestone regions, contain soluble phosphates in vary ing quantities. I think it safe to assert that phosphorus is nearly the most widely and evenly distributed element on the surface of the earth, and probably the most subdivided. This can be readily understood when the important part which phosphoric acid plays and has played in the vital cosmos is taken into consideration. Phosphorus was on the earth in gaseous, liquid or solid form before the dawn of life, and since then all animal and vegetable creation have combined with the

Jan 1, 1893

By John Hays Hammond

The following notes are descriptive of a country as yet in its infancy as regards the advancement made in mining operations. Its inaccessibility and other militating circumstances have retarded progress in that direction. With the completion of the railroad, now under construction, having the city of Cali as its objective point, with the concomitant civilizing and developing consequences, it is certain that the slopes of the Cordilleras will prove to be a South American Eldorado. Deposits of coal, copper, and minerals other than those of the precious metals are known to exist in quantities which, under more favorable conditions of accessibility, etc., could be profitably mined. The Government of the United States of Colombia, I think, is disposed to encourage and foster mining enterprises. Articles designed for mining are admitted free of duty; the permanency of the government is, at least, as well assured as that of Mexico (which is not noted for its immutability), and a more sincerely friendly sentitment towards Americans prevails in the United States of Colombia than in Mexico. This paper is confined to a description of the property of the Cauca company's mines, and is intended rather as a preliminary notice than as an exhaustive report. The Cauca mining district is reached by the following route: New York to Aspinwall; to Panama; to Buenaventura, a port on the west coast of the United States of Colombia, distant thirty-six hours from Panama by steamer; to Cali in the State of Cauca. The State of Cauca is bounded on the north by the Atlantic Ocean, on the northwest by the State of Panama, on the northeast by the States of Bolivar and Antioquia, on the east by Brazil and Venzuela, on the south by the Republic of Ecuador, and on the west by the Pacific. Ocean. It has a territory of 41,443 square miles, which is about one-tenth of the entire territory of the United States of Colombia. Its population, including the 50,000 savage Indians of the Caqueta (some of whom are cannibals), is nearly 450,000 souls, or about one-sixth of the population of the Colombian republic. Of these, one-fifth are whites (Spanish' South Amer-

Jan 1, 1885

By Paul G. Shewmon

The migration of slightly solzrhle spherical particles through a solid under the infllrence of a temperature gradient is analylzed for the cases of various transport mechanisms. It is shown that the variation of the velocity of the particles with radius, r, depends on the dominant mechanism of matter transport around or through the inclusion. Thus the velocity varies as r-1 jor surface-dijf1~sion controlled migratzon. is independent of r for volume diffusion in either phase, and varies as if the rate is determined by an interfacial reaction (n is the order of the interfacia1 reaction). These same results hold tor the migration of a cvlinder of length much greater than its radius. and .for other types of potential gradients, e.g., an electrical field. These equations are combined with recent electron-microscopic ohservations to show that the rate of migratzolz of small helium-silled bubbles through copper is determined by surface diffusion of the metal atoms. With these equations and the temperature gradients attainahle in an electron-microscope joil, the dominant transpar/ mechanism (or any migrating pnrtzclos can he determined. AS a result of fission, rare-gas atoms are created in the hot fuel element of a nuclear reactor. These insoluble atoms precipitate to form bubbles of the gas in the fuel. The subsequent migration and coalescence of these bubbles is thought to play a dominant role in the swelling of fuel elements which in turn can limit the fuel-element life. As a result of this practical problem and because of the relative simplicity of the system, workers in several laboratories have imbedded rare-gas atoms in metals with the aid of an accelerator and studied the formation and behavior of the bubbles that form on annealing. Recently Barnes and Mazey have studied the migration of such helium-filled bubbles in copper foils using the electron microscope and the temperature gradient that can be induced in the foil by the electron beam. They found that the smaller bubbles moved faster than the larger ones. It is shown below that, if this is true, the rate-controlling step in their migration is surface diffusion of metal atoms instead of volume diffusion, vapor transport, or an interfacial reaction. The analysis given is in no way limited to gaseous inclusions so the variation of velocity with particle size for any relatively insoluble precipitate particles could be used to obtain information about the relative importance of surface diffusion, volume diffusion, and interfacial reaction in such two-phase systems. VOID MIGRATION IN A TEMPERATURE-GRADIENT ANALYSIS Barnes' studies indicate that helium does not dissolve or diffuse in metals to a measurable extent, so that when the voids move they must do so through the movement of metal atoms from the leading to the trailing sides of the void.' Thus voids might move by surface diffusion, diffusion of vacancies in the surrounding lattice, or vapor transport. We consider first the case of flow by surface diffusion alone. We assume that there is a force, in the sense of irreversible thermodynamics, tending to move the atoms around the bubble in a given direction. We designate this direction as the x axis and the force per atom as Fa. The net rate of flow of atoms from one side of the bubble to the other, under the influence of this force, is the surface flux, Js, times the cross-sectional area available for flow, A,. A, is taken as the circumference times the thickness of the high-diffusivity surface layer 6. Thus where 51 is the atomic volume. For bubbles to advance a distance dx, a volume equal to nr : dx must flow around the void so that The minus sign enters because the bubble moves in the direction opposite to that of the force on the atoms. Equations for volume diffusion and diffusion through the vapor can be obtained in the same manner. For vapor transport we have Ag = and the ratio of the densities of metal atoms in the gas and the solid (pg/pl) enters so that

Jan 1, 1964

By Harry R. Hall

THE proposition to make pig-iron from magnetic concentrates and cobbed ore with charcoal-fuel weighing from 12 to 20 lb. per bushel is, on the face of it, not inviting; but the successful work that has been done under these adverse conditions warrants a permanent record in our Transactions, especially as it furnishes a comparison with, coke blast-furnace practice under similar conditions. The record of the furnace-practice is briefly summarized as follows:-The charcoal was made of hemlock, pine, spruce, balsam, maple, beech and birch woods. All the concentrates containing from 62 to 65 per cent. of iron would pass in. screen, of which about 34 per cent.. would pass an 80-mesh sieve. The cobbed ore, varying in composition from 32 to 47 per cent. metallic iron and from 23 to 32 per cent. of. silica, would pass through a I-in. ring, of which about 25 per cent. would pass a 1/8 in. screen. The furnace was blown in October 20,1903, with charcoal which was supposed to weigh when dry 18 lb. to the bushel. Some charcoal similar to this was stored in the stock-house for about a year and was then found to weigh 12 lb. per bushel. During the first 10 days of the blast, the furnace produced 362 tons of pig-iron, using 200 bushels of charcoal per ton of iron. From November 1st to 12th, the volume of the blast was increased gradually from 2,808 to 5,460 cu. ft. per minute, with practically no increase of output. The silicon-content of the resultant pig-iron averaged 0.75 per cent., with sulphur about 0.035 per cent. A supply of freshly-burned dry charcoal was then used which increased the silicon-content and lowered

Sep 1, 1905

By J. H. Schloen, C. W. Clark

Two papers have been written previously concerning operations at the Montreal East plant of Canadian Copper Refiners Limited. The first one,' written in 1932, described silver-refinery operations at the time for producing silver and gold bullion from tankhouse anode slimes; the second,2 published in 1933, consisted of a description of the entire plant. Since publication of these papers the refinery has become the world's largest producer of refined selenium. The first selenium was produced in August 1934. Tellurium production on a commercial scale followed in October 1935. This paper will deal with selenium and tellurium production and also with present operations in the silver refinery. Blister cakes from Hudson Bay Mining and Smelting Co., Flin Flon, Manitoba, and commercial anodes from Noranda Mines Limited, Noranda, Quebec, are refined at Montreal East. Both these bullions have unusually high gold, selenium and tellurium content. The average assay of raw slimes produced from domestic and Noranda anodes is about 40 per cent Cu, 3600 oz. per ton Ag, 800 oz. per ton Au, 22 per cent Se and 3.7 per cent Te. Early Silver-refinery Operations From the start of operations in 1931 until July 1934, the raw slimes were oxidize-roasted at 700" I?. in a Nichols-Herreshoff furnace, acid-leached with tankhouse discarded foul electrolyte (20 per cent H²SO), filtered and charged directly to the doré furnace for refining to doré meta1. This is the customary method for treating tankhouse anode slimes but was not suitable at the Montreal East plant because of the high selenium and tellurium content of our slimes. In the acid-leaching process about 50 per cent of the selenium and tellurium in the roasted slimes was dissolved in the electrolyte. These elements were recovered with the copper as a sludge in a small electrolytic

Jan 1, 1943

By C. W. Clark, J. H. Schloen

Two papers have been written previously concerning operations at the Montreal East plant of Canadian Copper Refiners Limited. The first one,' written in 1932, described silver-refinery operations at the time for producing silver and gold bullion from tankhouse anode slimes; the second,2 published in 1933, consisted of a description of the entire plant. Since publication of these papers the refinery has become the world's largest producer of refined selenium. The first selenium was produced in August 1934. Tellurium production on a commercial scale followed in October 1935. This paper will deal with selenium and tellurium production and also with present operations in the silver refinery. Blister cakes from Hudson Bay Mining and Smelting Co., Flin Flon, Manitoba, and commercial anodes from Noranda Mines Limited, Noranda, Quebec, are refined at Montreal East. Both these bullions have unusually high gold, selenium and tellurium content. The average assay of raw slimes produced from domestic and Noranda anodes is about 40 per cent Cu, 3600 oz. per ton Ag, 800 oz. per ton Au, 22 per cent Se and 3.7 per cent Te. Early Silver-refinery Operations From the start of operations in 1931 until July 1934, the raw slimes were oxidize-roasted at 700" I?. in a Nichols-Herreshoff furnace, acid-leached with tankhouse discarded foul electrolyte (20 per cent H²SO), filtered and charged directly to the doré furnace for refining to doré meta1. This is the customary method for treating tankhouse anode slimes but was not suitable at the Montreal East plant because of the high selenium and tellurium content of our slimes. In the acid-leaching process about 50 per cent of the selenium and tellurium in the roasted slimes was dissolved in the electrolyte. These elements were recovered with the copper as a sludge in a small electrolytic

Jan 1, 1943

By J. R. Long, E. T. Hayes, R. S. Dean, F. S. Wartman

THE production of titanium in 15-1b. lots and with a purity sufficient to be consolidated into ductile metal, as described in a previous paper,1 has provided adequate material for a study of the : physical properties of titanium and a more thorough examination of its working qualities. Data on the physical properties reported in that paper were obtained on metal fabricated by a fixed procedure, standardized for the purpose of control of the reduction, and are representative only of material fabricated under those conditions. There are many possible variables in the working schedule, which will have significant effects on the properties of the finished material; and since the previous working methods were not necessarily the best, an investigation of the fabrication of titanium by other methods was undertaken. In this work the consolidation of the powder by pressing and sintering was conducted essentially as outlined in the report cited' and all efforts were centered on fabrication methods for those powders and the properties produced by them. Hardness, density, microstructure, and tensile properties were determined at various stages in the working and annealing; and resistivity measurements were made on a few bars and drawn wire. [ ] CONSOLIDATION OF THE POWDER The screen analysis of the available titanium powder is given in Table I. No attempt was made to alter the size distribution from that noted because this powder, although coarse by normal powder-metallurgy standards, produced acceptable compacts suitable for the present work. Because of their large specific surface, finer powders are more contaminated by oxygen and produce harder compacts, which are difficult to work. The powder as produced is soft, compresses in a normal fashion, and exhibits very little tendency to adhere to the die surfaces. Unlike aluminum and magnesium powders, it can be readily pressed without the use of die lubricants. When compacted at so tons per

Jan 1, 1946

By Oscar E. Harder, H. A. Grove

It is now just a quarter of a century since Fred W. Taylor§(23) pub-lished his classical paper On the Art of Cutting Metals, describing his researches in which he, in cooperation with Maunsel White, had developed what is essentially the modern method of heat-treatring high-speed steels. Regarding this research, Dr. Sauveur,(22) in his address on Steel Wizards, Past and Present, at the annual banquet of the American Society for Steel Treating in Philadelphia in 1920 said, "The discovery of high-speed steel, or if you prefer, of the treatment imparting high-speed properties to certain steels by Taylor and Maunsel White I am inclined to consider as our one epoch-making contribution to the metallurgy of steel." It was at about that same time (1900) that Taylor exhibited high-speed steels, heat-treated by the improved process, at the World's Exposition in Paris and attracted much attention by showing that the steels would operate at such feeds and speeds that the tips of the tools were visibly red hot. This observation must have started metallurgists to wondering regarding the relative hardness of the various steels at red-heat temperatures. Considerable work has indeed been done in an effort to measure the hardness of high-speed steels and related materials in the red-heat range, using various methods. The result's, however, have been only partly satisfactory, owing to experimental difficulties. The present investigation had as it's immediate inception an address by J. V. Emmons, of the Cleveland Twist Drill Co., to the Columbus Chapter of the American Society for Steel Treating in 1931, in which he deplored the fact that comparatively little was known with regard to the hardness of high-speed steels at elevated temperatures, in spite

Jan 1, 1933

By Gerhard Derge

The rapidity of oxygen steelmaking has created renewed interesl in the mechanisms and kinetics of the various processes involved. These studies can now be approached with increased confidence because of the more adequate thermodynamics, physical chernislry, and relevant engineering infornzation available. These combine to offer promise of useful control and automation if the details of each specific problem can be sufficiently well-defined. The hot filament microscope provides new insig-hi into many of these problems by direct observation at temperature, allowing the appraisal of the relative importance of thermal gradients, convection, and intermediate phases. All of these have a direct bearing on the overall rates and control of most pyrometallurgical processes. It is one of the special privileges of the Howe Lecturer to become better acquainted with this distinguished man. All of us interested in the metallurgy of iron and steel have developed some sense of his widespread influence by the annual reference to his work in these Memorial Lectures. Each lecturer since 1923 has been able to identify his personal specialty with the broad interests of Professor Howe. This has become even more rewarding with the background information from Professor Gensamer's monograph, "Henry Marion Howe's Contributions to Metallurgy, which brings out his happy combination of intellectual and professional activities. Beyond this, I found my personal bond with Professor Howe in his book on The Metallurgy of Sleel first published in 1891.' After a detailed discussion of the dephosphorizing action of slags, he relates the mineral species identified in the frozen sample to the chemistry of the fused slag with the question, "Is it not most philosophic to hold that these independent entities were wholly integrated in the initial magma; that their presence in it was wholly

Jan 1, 1968

By T. L. Joseph

LARGE deposits of manganiferous iron ores, representing several million tons of metallic manganese, occur in the United States. The Minnesota deposits of such ore-are of outstanding importance because of their size, state of development, ease of mining and proximity to the Great Lakes, which permits water transportation to steel centers. In' view of the fact that our steel industry requires large quantities of manganese, for which no satisfactory substitute-has been found, and because our reserves of ferro-grade ore are comparatively small, the development of methods that will make our large deposits of manganiferous iron ores available as a source of ferromanganese is an important problem. Realizing the importance of this problem, some years ago the North Central Station of the U. S. Bureau of Mines and the Minnesota School of Mines Experiment Station undertook jointly the development of methods for recovering the manganese content of manganiferous iron ores in a: form suitable for the production of ferromanganese, the 80 per cent. alloy indispensable in producing steel. Two types of manganiferous iron ores have been described in previous reports. I The brown ores are higher in iron and lower in manganese than the black ores; the black ores are more siliceous but contain less phosphorus. The utilization of the iron content of the brown ores in the production of steel appears to furnish the best basis for their treat-ment. The method of attack has been to work out modifications in iron and steel practice so as to recover manganese in the form of slag comparable to ferro-grade ores. The greater part of the experimental work has been conducted with a 6-ton blast furnace and a Y2-ton basic open hearth. This paper is devoted mainly to open-hearth tests in which high-phosphorus spiegel

Jan 1, 1930

By Eric R. Jette

In order to control a chemical process by other than empirical, rule of thumb methods, two types of knowledge concerning the reactions involved must be available: (1) the thermodynamics of the reactions, and (2), by no means less important for efficient operation, the mechanisms and kinetics of the reactions. Information on the thermodynamic side enables the operator to decide upon initial and final conditions, whether heat must be added or removed from the system, whether the reactions proceed farthest in the desired direction at high pressure or low, etc. Knowledge of the mechanisms involves the determination of the individual steps by which an initial set of reactants, under given conditions, proceed to give the desired final products and kinetic studies upon which the mechanisms are based give the speed at which each of these reactions or steps take place. Thus thermodynamic studies of a reaction enable the operator to control the direction and extent to which the reaction can proceed, while kinetic studies enable him to control rates and thus the time efficiency of the operations. The thermodynamics set the limit to which the reacting system approaches; the kinetics tell how fast the system actually approaches this limit. The two types of information are complementary and not antagonistic even though in discussing the mechanism the introduction of thermodynamics is entirely needless and generally of no assistance, while in thermodynamic studies mechanism need not even be mentioned. Heterogeneous Reactions The thermodynamic side of metallurgical reactions has received much attention in the past; the mechanisms, relatively, very little. The main reason for our present lack of information on the mechanisms of these reactions lies in the fact that every one of importance is a heterogenkous reaction; i. e., the substances involved in the reaction exist in more than one phase, while, if we neglect the large amount of work which has been

Jan 1, 1931

By Mark C. Malamphy

The occurrence of outcrops of bituminous schists and sandstones impregnated with heavy asphaltie petroleum first directed attention to the São Pedro area as a possible source of commercial production of petroleum. Since 1920, more than 20 wells have been drilled in this area. The discovery of oil shows and small quantities of natural gas in some of the early wells led to the continuation of drilling in the hope that more important findings would result. During the early part of 1934, detailed magnetometer observations were made in this area, and a considerable number of torsion balance stations were occupied. The results of these geophysical observations help considerably to clarify the structure of the area and the very considerable amount of geologic information available makes possible a much more exact interpretation of geophysical anomalies. In presenting the results of these observations, and interpretation of the geophysical data, certain actual case problems are included; i.e., geophysical anomalies due to anomalous masses of which the forms and positions are more or less known. Although anomalies due to igneous intrusions are probably more important to geophysicists in Brazil than in other countries, these data have a certain interest for all geophysicists, particularly because they were obtained in the south magnetic hemisphere, where the lines of magnetic force are directed upward, and in a region of moderately low inclination. This is considered as a geological-geophysical problem, and only passing mention will be given to the petroleum possibilities of the area. General Geology The location and general geology of the São Pedro area are shown in the sketch map of Fig. 1, which is adapted from the geologic map of South Brazil compiled by Oppenheim1,†- who gives the geologic column of South Brazil (So Pedro and vicinity) as follows:

Jan 1, 1940

By Mark C. Malamphy

The occurrence of outcrops of bituminous schists and sandstones impregnated with heavy asphaltie petroleum first directed attention to the São Pedro area as a possible source of commercial production of petroleum. Since 1920, more than 20 wells have been drilled in this area. The discovery of oil shows and small quantities of natural gas in some of the early wells led to the continuation of drilling in the hope that more important findings would result. During the early part of 1934, detailed magnetometer observations were made in this area, and a considerable number of torsion balance stations were occupied. The results of these geophysical observations help considerably to clarify the structure of the area and the very considerable amount of geologic information available makes possible a much more exact interpretation of geophysical anomalies. In presenting the results of these observations, and interpretation of the geophysical data, certain actual case problems are included; i.e., geophysical anomalies due to anomalous masses of which the forms and positions are more or less known. Although anomalies due to igneous intrusions are probably more important to geophysicists in Brazil than in other countries, these data have a certain interest for all geophysicists, particularly because they were obtained in the south magnetic hemisphere, where the lines of magnetic force are directed upward, and in a region of moderately low inclination. This is considered as a geological-geophysical problem, and only passing mention will be given to the petroleum possibilities of the area. General Geology The location and general geology of the São Pedro area are shown in the sketch map of Fig. 1, which is adapted from the geologic map of South Brazil compiled by Oppenheim1,†- who gives the geologic column of South Brazil (So Pedro and vicinity) as follows:

Jan 1, 1940

By Sidney Siegel, J. Gardner Brooks, Irvin R. Kramer

IN 1942 Grossmann1 proposed that the hardenability of a steel may be calculated from its chemical composition by considering the base hardenability associated with its carbon content and grain size and multiplying this base by factors for each element present. Since Grossmann's original publication, several investigators2-5 have reexamined the multiplying factors for the individual elements and in general have found that the multiplying principle is valid. However, some of the individual factor curves developed have been in poor agreement. Inasmuch as the carbon-factor curve obtained by Grossmann was dependent [ ] upon the factors for all the other alloying elements present in the steel, it logically followed that his results were in need of correction in the light of the new data available for manganese, silicon, and the other alloying elements. Furthermore, in order to avoid the possibility that errors in the manganese, silicon, or other curves might influence the carbon-factor curve, investigation of iron-carbon alloys containing little or no manganese and silicon was necessary. That the effect of carbon on hardenability was greater than indicated by Grossmann is shown by a comparison of the diameters of completely hardened rounds of iron-carbon alloys with the ideal critical diameter calculated from Grossmann's factors. These alloys have a greater hardenability in a hite quench than predicted by Grossmann's factors for an infinite quench (Table I). [ ] Among the other important variables that were in need of further investigation were the effect of deoxidation practice on the grain-size correction curves and the effect of stable carbide-forming elements on the depth of hardening. Most of the work by Kramer, Hafner, and Toleman4 was done on silicon-killed steels. It was not known whether Grossmann's grain-size correction curves, deter- mined on aluminum-killed steels, was valid when applied to steels with different deoxidation practice. More data on the

Jan 1, 1946

By T. M. Chance

THE first bituminous coal cleaning-plant to use the sand-flotation process1 was placed in operation on Oct. 1, 1925, at the tipple of the East Broad Top Railroad & Coal Co., at Mt. Union, Pa. The general principles governing the design of plants of this type and typical operating results of anthracite sand-flotation units have been previously outlined.2 I will, therefore, confine myself to a description of this particular plant and to some of the elements of design it incorporates. THE ORIGINAL MT. UNION TIPPLE The plant was installed to transfer coal from steel narrow-gage cars of 60,000 and 70,000 lbs. capacity to standard-gage equipment. The coal was hauled some 30 miles from the East Broad Top field. This coal, mined by the Rockhill Coal & Iron Co. and other operators, is a low-volatile slow-coking coal with- ash of high-fusion point. It is normally a high-grade coal that does not contain an excessive amount of free impurities, but it requires careful handling to secure a fair domestic yield, and, naturally, the need for narrow-gage transshipment increases the difficulty of the problem. The narrow-gage cars were discharged into an 8-car track hopper equipped with two feeders passing the coal to two 42-in. apron intake conveyors. Twin units were installed throughout in this original plant, two lump-and-egg shaking screens, two lump picking-tables, two egg picking-tables and two stoker conveyors. The stoker coal was loaded without cleaning. The loading tracks and booms were in duplicate and with the layout as originally installed either unit could be run independently, each unit shipping a different class of coal or both units making the same product.

Jan 2, 1926

By T. M. Chance

The first bituminous coal cleaning-plant to use the sand-flotation process1 was placed in operation on Oct. 1, 1925, at the tipple of the East Broad Top Railroad & Coal Co., at Mt. Union, Pa. The general principles governing the design of plants of this type and typical operating results of anthracite sand-flotation units have been previously outlined.2 I will, therefore, confine myself to a description of this particular plant and to some of the elements of design it incorporates. The Original Mt. Union Tipple The plant was installed to transfer coal.from steel narrow-gage cars of 60,000 and 70,000 lb. capacity to standard-gage equipment. The coal was hauled about 30 miles from the East Broad Top field. This coa1, mined by the Rockhill Coal & Iron Co. and other operators, is a low-volatile slow-coking coal with ash of high-fusion point. It is normally a high-grade coal that does not contain an excessive amount of free impurities, but it requires careful handling to secure a fair domestic yield, and, naturally, the need for narrow-gage transshipment increases the difficulty of the problem. The narrow-gage cars were discharged into an 8-car track hopper equipped with two feeders passing the coal to two 42-in. apron intake conveyors. Twin units were installed throughout the original plant, two lump-and-egg shaking screens, two lump picking-tables, two egg picking-tables and two stoker conveyors. The stoker coal was loaded without cleaning. The loading tracks and booms were in duplicate and, with the layout as originally installed, either unit could be run independently, each unit shipping a different class of coal or both units making the same product.

Jan 1, 1927

By T. Sterry Hunt

THE geognostical relations of the metals and their ores present many problems of great interest, alike for the geologist, the chemist, and the mining engineer. The association with certain rock-formations of characteristic mineral species may help to guide the geologist in the identification of geological horizons, and throw light on the chemical activities which have been especially manifested in certain periods; while it is clear that such relations, if established, must be of great utility to the miner, and especially to the explorer of new regions. In inquiries of this kind, however, it is only by careful observations over wide areas, and by the collocation of a great number of facts, that anything like a safe basis for induction can be attained. The effects of hasty and imperfect generalizations in this field have already in many instances been felt to the prejudice of scientific progress. I come before you to-night, therefore, not to lay down any laws or general principles, but to call your attention to certain facts, many of them doubtless known to you, which have forced themselves on my attention, with regard to the associations of various metallic ores and other useful minerals with different series of stratified rocks, and to ask you to aid the progress of this branch of geognostical inquiry. Your observations in the various regions to which you may be called by your professional duties will enable you to determine how far these associations are mere coincidences, and how far they are chemical and geological constants. The associations here to be noticed concern only those mineral species which occur, either distributed through the strata in such a manner as to show that they are contemporaneous deposits, or occupy rifts or gash-veins in these strata, and may be supposed to have been