Search Documents

By W. C. Knopf, G. Samsel

For several years International Minerals & Chem-ical Corp. has used a radiation method to assay potassium content of products from potash and feldspar beneficiation. The procedure is rapid, accurate, and inexpensive and is easily handled, if necessary, by nontechnical personnel. Data are presented to show the accuracies that may be expected if the technique is used for control of pilot plants or large-scale plants. Natural potassium is composed of three isotopes —K, K and K. Five other isotopes, artificially produced, have been detected. In natural potassium only the K isotope, with a half life of 1.4x10 years, is radioactive. Its modes of decay are beta and gamma rays, positrons, and x-rays. Only the more abundant beta rays, however, are important in radiation measurements using geiger tubes. Barnes and Salley' measured radiation of potassium salts in solution in 1943. Gaudin and Parnell2 first reported the use of solid salts arranged in a vessel surrounding the ß counter in 1948. Later, Scheel used the method to assay potassium content of various crude and finished potash salts. Experimental: Dip-type Geiger-Muller tubes (TGC-5) supplied by Tracerlab Co. were used in all radiation counting measurements. The tube was encompassed by a glass container about M in. larger in diameter than the tube. This container, which served as a sample holder, was closed at the bottom with a rubber stopper to facilitate removing the samples. Samples were not weighed, but about 40 g of sample were needed for each test. Electrical impulses from the tube were counted on either a Tracerlab scaler or a rate meter. To obviate the need for constant attendance, preset features were incorporated into the scalers, so that at a predetermined time or count the units were automatically deactivated. When rate meters were used, counting rates were read directly from instrument or from a recorder used in conjunction with the rate meter. Each tube was calibrated, according to the manufacturer's instructions, to determine the correct operating voltage to insure reproducible results. A linear calibration plot of percent K2O vs counting rate was also obtained for each tube by recording the counting rate plus background count of several standards of different K2O content chemically analyzed by the chloroplatinate method.' These standards were of approximately the same particle size distribution as samples to be assayed. Specific background count caused by cosmic rays and other surrounding radiation was checked periodically by counting a sample of pure NaCl. Fig. 1 is a representative calibration plot. Assays were determined directly from the standard plot or calculated by subtracting the background count from the counting rate, then multiplying by the slope of the line. Chemical assays of the test samples were made by the Sherril method," a flame photometric technique, or the chloroplatinate method. Data: The radiation assay method has been used for three years by International Minerals & Chemical Corp. in the laboratory and in pilot plants processing ores containing potassium. These dry concentration plants process sylvinite and langbeinite ores at Carlsbad, N. M., and feldspar ores at Top-sham, Maine. Sylvinite ore is predominantly a mixture of syl-vite (impure KCl) and halite (impure NaCl). Contaminants include sulfates, such as langbeinite (2MgSO - K2SO4), kieserite (MgSO H2O), poly-halite (MgSO4.K2SO, 2CaSO, . 2H2O), and slimes. Langbeinite ore is predominantly langbeinite and halite with small amounts of sylvite, sulfates other than langbeinite, and slimes. Several variables, in addition to correct calibration and standardization of tubes, were found to be important in obtaining reproducible results. Particle size distribution of standard samples should be

Jan 1, 1959

By William M. Bowron

In the hope that a brief description of the conditions that are favorable or unfavorable to success in the practical treatment of titaniferous ores in the blast-furnace may not be without interest to the members of the Institute, the present paper is submitted. The class of ores of which I speak may be described as magnetites, with a gangue of siliceous matter, in which a portion of the silica is replaced by titanic acid. Professor Dana, in his System of Mineralogy, gives a long list of representative analyses of titanic iron ore in which the percentage of titanic acid varies from 59 down to 34. If the percentage is below the latter figure, the ore is no longer recognized as a "titanic ore;" although, according to my experience, titanic acid is present, in small quantities, in almost all ores. In the methods followed in ordinary analysis it is usually included with the "insoluble matter," unless special search is made for it. In the ores usually regarded as "titanic "the proportion of titanic acid frequently assumes quasi definite percentages, such as from 4 to 5, 8 to 9,12 to 13, and so on, in an ascending scale to those higher percentages that do not at present concern us. The proportions quoted characterize large masses of ore that are now accessible to market and are lying idle only on account of the titanic stigma. My experience with titanic acid in the furnace began in England, fourteen years ago, with my being employed as chemist by the manager of the Norwegian Titanic Iron Company, which was at that time smelting, without mixture, ilmenite from Norway in a furnace 16' X 50'. The process, regarded as a process, was a perfect success; but the enormous quantity of fuel required, the small quantity of iron in the ore, and the cost and uncertainty of importation militated seriously against its commercial success, and a few years saw the attempt abandoned. The metallurgy being successful, an at-

Jan 1, 1883

By C. E. Arnold

IN attacking the problems of mining and treating large disseminated copper orebodies such as those occurring in the Miami or the Ray district of Arizona, one of the vital questions to be decided is, "What is the value of the orebody per ton in place?", The importance of this question lies in the fact that its answer helps to reach a decision concerning the method of mining to be employed. Let it be assumed for the moment that milling and smelting practice, especially the latter, is more or less standardized; and has a cost incapable of much variation, while the cost of mining has a considerable range owing to the large number of mining methods by which a mine may be exploited. For instance, a method may be adopted whereby all the available ore can be extracted perfectly clean (i.e., unmixed with barren material) at a relatively high cost; or a method may be used involving the necessary dilution of a portion of the ore with waste, in order to recover that portion, thus giving a relatively poorer extraction but nevertheless a lower working cost than the former method. Naturally, between these two extremes there lie intermediate methods. In order to arrive at a solution of a mining method problem that is of any value, it is necessary that accurate and complete estimates of mining, milling, and smelting performances and costs shall be established. By way of illustration is given a, case of mining, by the system of undercutting and caving, a large orebody with an average content of 1.50 per cent. copper supposedly all in sulphide form, to which case has been applied those results in mining operations which one may fairly assume are to be expected when viewed in the light of G. R. Lehman's ore-drawing experiments, which form the subject of a paper to be presented at this meeting. It is assumed that the total. costs will be as shown in the following table:

Jan 9, 1916

By J. O. Brittain, E. Lautenschlager

Yield point measurements were made on polycrys-talline specimens of a iron deformed various amounts at 770, 1950, or 273°K, aged, and redeformed at 77: 195°, or 273°K. When the prestrain temperature is lower than that subsequent to aging, the yield point return is suppressed relative to specimens deformed at the same temperature both before and after aging. The degree of suppression is a function of both the magnitude of prestrain at the lower temperature and the difference between the deformation temperatures before and after aging. It is proposed that the suppression is caused by the formation of dislocation barriers during the initial low-temperature deformation. The aging kinetics of polycrystalline a-iron wires deformed at 77o or 303oK were studied at 44 " and 64 "C using internal friction measurements. No change was noted as a result of the difference in prestrain temperature. IN an earlier investigation1 it was observed that the return of the yield point was suppressed when a poly-crystalline specimen of a iron was plastically deformed at 77oK, aged at room temperature, and subsequently tested at room temperature. In order to investigate this observation, a research program was undertaken to measure the effect of prestrain temperature on the strain aging of a iron.' According to Thomas and Leak,3 return of the yield point and internal friction are similar measures of strain aging since both are dependent on solute atoms leaving the solid solution. The decrease in internal friction as a function of aging time is indicative of the removal of solute atoms from the solution, while the return of the yield point as a function of aging time gives the rate of arrival of solute atoms at the dislocations. According to Cottrell and Bilby,4 the solute atoms create an "atmosphere" which locks the dislocations and causes a return of the yield point upon restraining. In this experiment, both methods of measuring strain aging were employed in order to have two independent measurements of the strain aging phenomenon. In a previous study,5 the strain aging kinetics of a similar lot of a iron were measured for specimens which were prestrained and tested at the same temperature over the range of 77" to 273°K. Although some differences were found in the correlation of the two methods employed for measuring strain aging, the kinetics of strain aging were unaffected by the change of prestrain and test temperature. In another study,6 dislocation line tension and the density of the solute atmosphere were found to contribute to the return of the yield point when ingot iron specimens were prestrained at 303°K and tested at a lower temperature, namely 77°K. This paper is concerned with changes in strain aging kinetics produced by pre-straining at 77" to 303°K and testing at either the prestrain temperature or at higher temperatures up to 273°K. EXPERIMENTAL PROCEDURE The polycrystalline a iron specimens used in both the tensile and internal friction tests were 0.033-in. diam ingot iron wires, wet hydrogen treated and re-carburized. A more detailed procedure for processing a 3/16 in. ingot iron rod (nominal wt. pet composition: Fe - 0.013; C - 0.0125; Mn - 0.023; Si -0.005; P - 0.0023; S - 0.11; Cu - 0.004 N) to 0.033 in. diam specimens containing approximately 0.020 wt pet C and no detectable nitrogen with a grain diameter of 0.033 to 0.040 mm is given elsewhere.5 Immediately prior to testing, specimens were solution treated for 15 min at 700o ± 2°C in a static vacuum of less than 50 ?. of Hg and rapidly quenched into an ice-water bath while still enclosed in a 3 mm quartz vial. The internal friction specimens had 8-in. gage lengths and the tensile specimens had 2-in. gage lengths. The wires used as tensile specimens were first run as internal

Jan 1, 1962

By G. S. Hume

IN THE autumn of 1922, British Petroleums Ltd. found oil of 14° Baume in a sand 17 ft. thick in its No. 2 well at Wainwright, 120 miles southeast of Edmonton. This greatly encouraged drilling in the Wainwright-Irma area and this past summer several wells were started, three of which are now completed' and the others still being drilled. Of the three completed, No. 4 British Petroleums contains oil; No. 3 British Petroleums gave a show of oil but so far has not given much hope of becoming a commercial producer; and No. 1 Maple Leaf Co., as now finished, is a gas well with a daily flow of gas of about 2,500,000 cu. ft. at a closed pressure of 700 lb. An oil sand is reported . to have been encountered below the producing gas horizon, in the Maple Leaf well but has not been tested. Operations on this well have been suspended for the winter. The Geological Survey of Canada this past summer undertook a geological investigation of this area with the object of defining the structures with which the oil and gas are associated. The 'structure underlying this portion of the plains was supposed to-be a terrace with the western edge dipping into the Alberta syncline and with a monoclinal structure to the east. By accurate leveling on known geological horizons on this terrace, a number of gentle folds were located and it is in these folds that the oil land gas are found. At the British Petroleums Nos. 2-and- 4 oil wells, the western flank of the fold has a gentle dip of only a few feet to the mile to the southwest whereas the strata on the eastern flank dip to the northeast about 40 ft. in 1/2 mile, the strike of the fold being northwest and southeast. How far oil will be found down the gentle southwest dip is unknown but probably the productive part of the fold will not exceed 1 mile in width, and possibly less. No. 3 British Petroleums well is on the strike of the fold 1 mile southeast of the two oil wells. The sand that was productive in Nos. 2-and 4 wells was not present in this well or, if present, was very thin and unproductive. Two other sand horizons, however, were encountered. The upper of these

Jan 3, 1925

By Colin M. Sargent

THE electron diffraction pattern as seen in the electron microscope represents an approximately plane section of the reciprocal lattice. Identifying the zone axis of a diffraction pattern is often laborious for a crystal of low symmetry, especially if several crystal orientations are present. A program has been written in FORTRAN II (Version 2) for the IBM 1620 which will assist in plotting out reciprocal lattice sections. The calculation is performed by choosing a zone axis [uvw] and determining the d spacings and angle between the planes (Ow - v) and (wO - u). (This procedure is varied slightly for zone axes with Miller indices equal to zero.) Cartesian coordinates for the reciprocal lattice points are then calculated for these planes and for (ww— [u + v]). Any reciprocal lattice points within the parallelogram formed by the origin and these three points are then computed. The input and output are best described by use of an example (Monoclinic ZrO2) used in the author's work. Input consists of two cards: 1) The crystal parameters: a, b, c, a, 8, y, e.g., 5.1477, 5.2030, 5.3156, 90.000, 99.380, 90.000. 2) Three numbers, D, E, F, e.g., 5, 3, 3.0710-the first is the limit of the sum (u + v + w) considered; the second limits the absolute value of u, v, and w to (E- 1), e.g., 2, so that zones (221) would be the highest order considered in this example; the third, F, is the required constant, yL. Output is in the format shown in Table I. The reciprocal lattice sections may then be plotted on standard graph paper and compared with the unknown diffraction pattern. (Note that no attempt has been made to deal with systematically absent reflections.) A card deck for the program is available from Colin M. Sargent, ARZ, W-PAFB, Dayton, Ohio, 45433.

Jan 1, 1969

By Charles C. Towle, Irving Rapaport

URANIUM mineralization along the north flank of the Zuni Uplift, in the vicinity of Haystack Butte, was discovered by Paddy Martinez, a Navajo Indian, in the spring of 1950. The find was reported to the Santa Fe Railway Co., which initiated a program of exploration upon its holdings in the district in December of 1950. The Anaconda Copper Mining Co. secured numerous leases in January and February, 1951, and began an intensive exploration and development program in March 1951. The district was extended into the Lucero Uplift in August of 1951 by the discovery of uranium mineralization in Todilto limestone by Joy Sinyella, a Supai Indian living on the Laguna Reservation. Initial reconnaissance was performed in the district by the Atomic Energy Commission in November 1950. A field office under the direction of the Denver Exploration Branch of the AEC was established at Prewitt, N. Mex. in January 1951 to study regional and detailed guides to ore, to evaluate the ore deposits, and to promote the development of the district by providing geologic services for the companies and individuals engaged in exploration. With the development of sufficient ore to warrant construction of a mill, the Grants area of New Mexico has come of age as a full fledged uranium mining district. The carnotite-type deposits of Grants, the first of major economic importance found in limestone, have extended the Colorado Plateau carnotite field into the more complex structure of the Basin and Range Province. General Geology The Grants uranium district is in northwestern New Mexico, along the southern flank of the San Juan Basin, between the cities of Gallup and Albuquerque. The region is at a mean altitude of about 6800 ft, vegetation is sparse, and outcrops are excellent. Mt. Taylor volcanic peak, at an elevation of 11,400 ft dominates the surrounding area. The overlying cliff-forming Dakota sandstone is the most resistant formation in the Grants District and characteristically erodes into dissected mesas as much as five miles wide. The principle uranium ore-bearing horizons are found in the underlying Morrison formation, and the Todilto limestone of the San Rafael group. The Morrison weathers into. a series of steep slopes and precipitous cliffs near the lower part of the Dakota-capped rims, while in contrast, the relatively resistant underlying. Todilto [ ] limestone forms broad benches extending out from the base of these Dakota rims as much as five miles wide. The Todilto benches are covered with overburden to an average depth of about 5 ft in the first thousand ft away from the Dakota rim, but increases to about 200 ft at the base of the rim. In many places however, a thick mantle of upper Cretaceous sediments and Tertiary volcanics "obscures the ore-bearing Jurassic, and precludes exploration. . The known uranium deposits of the Grants District are distributed throughout a zone 85 miles long and about 10 miles wide. Stratigraphy Rocks from pre-Cambrian through Tertiary are exposed in the uplifted areas, but uranium appears to be restricted chiefly to two zones in Jurassic sediments. The Jurassic sediments of the Colorado Plateau have been subdivided into three units, in ascending order: (1) Glen Canyon group, (2) San Rafael group, (3) Morrison formation. The Todilto limestone zone within the San Rafael group has produced the bulk of ore to date, but the promise of the Morrison zone is rapidly increasing. The Todilto formation extends about 300 miles east-west and about 100 miles in a north-south direction. It is composed of a lower, extensive, limestone member and a central, more restricted, thick, pure gypsum member. The Todilto is believed to be of lacustrine origin. The Morrison formation in this area is subdivided, rather arbitrarily, into three members: Recapture Creek, Westwater Canyon, and Brushy Basin. Ore

Jan 1, 1952

By S. K. Tarby, A. E. Rathke

A series of 0.21 pci carbon steel melts was processed under conditions which sinzulated industrial vacuum degassing practices. The results indicated that the efliciency of carbon deoxidation was not significantly increased by vacuunz degassing at chamber pressures below 100 torr. The two common phenomena of vacuu?rz carbon deoxidation, i.e.,an unaccountable carbon loss and nonequilibrium deoxidation, were observed in this study. Oxygen from adsorbed and chenzically combined water of certain refractory structures was probably responsible for the unaccourttable carbon drop. The nonequzlibrium deoxida-tion phenomenon was adequalely correlated by a bubble nucleation )mechanism. Although the major limiting factor in oxygen removal from these melts contained in alumina crucibles could not be eslablished with certainty, there was some evidence that melt-refractory interactions were not the most imp-portant limiting factor. CONSIDERABLE attention has been given to the use of carbon in conjunction with vacuum degassing* as a deoxidation technique. An advantage of utilizing the reaction: for deoxidation purposes is that the reaction product is gaseous and hence can be effectively removed from the melt. The pressure dependency of Eq. [I] is illustrated by the expression for the thermodynamic equilibrium constant, K: where pco is the partial pressure of carbon monoxide, and hc and ho are, respectively, the Henrian activities of carbon and oxygen in molten steel. The thermodynamic aspects of the C-0 reaction in molten Fe-C-0 alloys have been investigated extensively. Theoretical predictions based on Eq. [2] indicate that, at the chamber pressures reached in most vacuum degassing units, carbon is the most effective deoxidizer that can be obtained. ~ornak' has compared industrial values of carbon and oxygen contents with values calculated from theory, and has shown that on a commercial basis vacuum carbon deoxidation has not achieved the degree of success that is predicted from theoretical considerations of the C-0 reaction. The use of industrial units to determine the reason for this deviation is limited by economics and the difficulty in controlling critical process variables. Therefore laboratory-sized experiments in this area should yield valuable information. Investigations on vacuum carbon deoxidation have been made in experiments conducted under vacuum induction melting conditions where pressures in the low micron range, long treatment times, exposure to highly dynamic vacuum conditions, and relatively quiescent bath conditions have been maintained. Inve~ti~ators~~~ utilizing vacuum induction melting for the production of high-purity iron by carbon deoxidation have concluded that, under high vacuum conditions, melt-refractory interactions constantly supply oxygen to the melt. Thus, it has been suggested that refractory dissociation rather than the C-0 reaction establishes the lowest possible oxygen content of a melt. Thomas and Moreau4 and Bennett, Protheroe, and ward5 have studied carbon deoxidation of Fe-C alloys melted in magnesia crucibles under reduced pressures. The results of both studies differed considerably from those predicted by theory, and the limiting factor for lower oxygen contents was attributed to melt-refractory interactions. Because the refractory material used in both investigations was magnesia, no quantitative measure of crucible reaction could be made and the amount of carbon consumed during treatment was utilized as an indirect indication of the extent of crucible reaction. Studies concerned with the determination of the minimum oxygen content attainable in pure iron and Fe-C alloy material vacuum-induction-melted in various crucible materials have also been conducted."' The suitability of a crucible refractory for use under vacuum conditions appears to depend upon the major refractory constituent, the amount and type of impurity oxides, and the composition of the melt. Meadowcroft and Elliott9 have presented a theoretical review of the type and extent of various refractory reactions which should be considered in vacuum refining. ~eadowcroft'~ considered the vacuum degassing process to be dependent upon the "carbon boil" and has proposed that a part of the difference between the experimental and theoretical results for vacuum carbon deoxidation may be explained by the fact that the pco term in Eq. [2] is not the chamber pressure. Instead, the pressure necessary for carbon monoxide

Jan 1, 1970

By U. F. Kocks

The flow stress in some latent slip systems of aluminum and silver crystals after various deformations in single slip was investigated by transverse compression and supplemented by experiments on overshoot of the compression axis and the stability of corner orientations. Work hardening was found to be remarkably isotropic, the ratio of the flow stress in the latent system to that in the primary system being between 1.0 and 1.3. The strain-rate dependence was not significantly larger in the latent system. This low anisotropy suggests that specific dislocation interactions are not the direct cause of work hardening. Either the obstacles are essentially impenetrable so that only their distance enters, or a fairly random distribution of dislocations of all systems is. in fact. formed during single slip. The latter seems to he excluded by the observations on the strain-mte dependence and on the amount of secondary strain. The amount of seconzdary strains occurring in single slip was determined by shape-change mensurements and by a new method connected with the latent-hardening experiments. It is definitely less than 1/300 times the strain in the primary svstem. WORK hardening is due to dislocation interactions; this is a hypothesis, and possibly the only one, on which all present work-harden ing theories agree. About a dozen specific interactions have been considered, and it is unlikely that any essential one has been missed. Different work-hardening theories differ to a large extent in the specific interactions which are deemed most important. The presence or absence of any particular interaction, and its degree, depend on the geometrical relationships between the two dislocations interacting. Let us enumerate some examples. Two dislocations may react, with a varying reaction energy, to form a third dislocation, and this reaction product may be sessile or glissile. Two dislocations may intersect and a jog may be formed on both, on one of them, or on neither; this jog may be sessile17Z or glissile and it may, if moved nonconservatively, lead to the production of vacancies or interstitials. Finally, a dislocation may bypass another one and thus interact only with its stress field. All these interactions depend on the specific relation between the Burgers vectors and line directions of the two dislocations. Any dislocation generated during plastic deformation of fcc crystals belongs to one of twelve slip systems. Taking any one dislocation, its relationship to each of the other eleven can fall, by symmetry, into one of only five classes. These relationships are enumerated in Fig. 1 and Table I. Each slip system is represented in the stereo-graphic projection by two triangles, namely those in one of which the specimen axis would have to lie if the specimen were to deform in single slip on this slip system in a given sense, in a tension test. Let us represent the primary slip system by the shaded triangles. The other slip systems are classified only with respect to their relationship to this primary system. The code letters (initials of established names* in German) are explained in Table I. Three specific interactions are also listed in cases where they may be strong: the product of a reaction, the formation of jogs in either system, and the elastic bypass stress. The last column relates to the types of experiments reported in this paper and summarizes their results. To decide experimentally between the relative importance of the various interactions one would like to produce a group of dislocations in one slip system and then measure the stress necessary to force another group of dislocations of a specific second system through them. Hopefully, one can produce the first set of dislocations by plastically deforming the specimen in single slip. Then one can try to achieve single slip in a specific, previously latent system and measure its flow stress. If it is different from the virgin flow stress, there has been "latent hardening". Some types of latent-hardening experiments will be discussed in the next section. The strain-rate and temperature dependence of the flow stress is an indication of the importance of dislocation intersections. By extending an investigation of this dependence to the latent systems, one can determine how much more important forest contributions are here. seeger3 has used the as-

Jan 1, 1964

By H. L. Gilbert, W. W. Stephens

Production of anhydrous zirconium tetrachloride by direct chlor- ination of a zirconium oxide carbon mixture in a silica-brick-lined chlorinator is described. Theory and thermodynamics of reactions are discussed. A pilot-model chlorinator and full-scale production equipment are described and operating data are included. ANHYDROUS zirconium tetrachloride required as a starting material in the Kroll process for production of ductile zirconium has been produced in this country principally by chlorination of the carbide or "carbonitride" made by reduction of zircon sand concentrates with carbon in the arc furnace. This process and the equipment used have been fully described.'.' It is well known that zircon or badde-leyite ores may be chlorinated directly with chlorine in the presence of carbon, and this one-step approach would seem at first glance to be preferable to the two steps involved in the carbide-chloride operation. As previously discussed1 considerations leading to adoption of the longer process were: 1—Chlorination of the carbide proceeds rapidly at temperatures below 500°C, whereas temperatures above 900°C were considered necessary for chlorination of zircon-carbon mixtures. 2—The highly exothermic nature of the carbide-chlorine reaction makes it self-sustaining, while heat must be supplied continuously in direct chlorination of the ore. 3—Silicon was thought to be chlorinated along with zirconium in the direct chlorination of zircon, leading to high chlorine consumption. In production of carbide in the arc furnace, silicon is driven off as silicon monoxide and does not enter the chlorinator. 4—For efficient direct chlorination, the ore must be finely ground and intimately mixed with carbon, and the mixture briquetted. 5—Direct chlorination requires a much larger chlorinator for a given production capacity than chlorination of carbide. Recently it has become necessary to produce large quantities of zirconium metal from a chemically purified zirconium oxide. Since the cost of the latter is high, the relatively high losses encountered in production of carbide in the arc furnace could not be tolerated, and a graphite resistor furnace5 was developed for production of carbide, which was then chlorinated in equipment previously used for chlorinating arc-furnace carbide. This method of operation was quite satisfactory, and losses in the carbid-ing step were minimized. However, operating costs were relatively high, and the process did not lend itself particularly well to large-scale operation because of the multiplicity of small units required and the hand labor needed to load, unload, and maintain the furnaces. To chlorinate the carbide, a vertical-shaft chlorinator was used in which the charge was heated with a central split graphite-rod resistor.' Operation of this chlorinator was somewhat less satisfactory with the resistor furnace carbide than it had been with the arc-furnace carbide due, principally, to the differences in physical properties of the carbide. The arc-furnace carbide is obtained as a fused metallic-appearing mass which can be crushed to -1/4 in. with production of a minimum of fines, whereas the resistor-furnace product is lightly sintered and produces a large proportion of fines in crushing and handling. These fines tend to pack in the chlorinator and promote channeling. which results in poor chlorine efficiency and low capacity. Data based on production of 22,000 lb of chloride from resistor-furnace carbide in this equipment are shown in Table I. Necessity for increasing production of chloride from about 2,000 to 15,000 lb per week led to further investigation of possible methods for direct chlorination of the oxide or oxide-carbon mixtures. Direct chlorination of the pure oxide presents much less difficulty than chlorination of zircon sand or oxide ores. The oxide is easily ground to —200 mesh, and no silica is present to cause excessive consumption of chlorine or contamination of the product. Theoretical Considerations The principal chemical reactions involved in chlorination of mixtures of zirconium oxide and carbon may be written as follows: ½ ZrO2 (c) + C(c) + Cl2(g) = ½ ZrCl,(g) + CO(g) [I] 1/2 ZrO, (c) + CO(g) + Cl2(g) = ½ ZrCl,(g) + CO2(g) 121 ½ ZrO2 (c) + ½ C(C) + Cl2(g) = 1/2 ZrCl4(g) + ½ CO2(g) [3]

Jan 1, 1953

By C. G. Dunn, P. K. Koh

Microstructure, magnetic torque, and texture data before and after grain growth were obtained on two 3.25 pet Si-Fe specimens having initially the same cold-rolled textures and the same primary recrystallization textures. The latter textures consisted of four components, two only of which were strong; the strong components were near (120) [001] and (320) [001]. The textures of the two specimens obtained by grain growth were different. In one specimen the two weak components were converted into strong components by a secondary recrystallization process; in the other specimen the primary recrystallization texture was retained by a normal grain-growth process. The difference in behavior of the two specimens was interpreted in terms of a difference in the relative grain sizes between weak and strong components; i.e., in terms of a geometrical factor that would alter the early growth rates of grains belonging to the two weak components of the texture. Specifically the growth rate was considered as the product of two terms: a driving force and a boundary mobility. The texture changes observed are considered to favor the oriented-nucleation growth-selectivity theory more than the oriented-growth theory. WHEN primary recrystallization and grain-growth textures form as a result of annealing deformed metals or alloys, the fundamental processes involved are nucleation and growth. Knowledge, therefore, about nuclei and the factors influencing their growth is required not only for the understanding of texture development but also for its control. In the oriented-growth theory of texture formation1, 2, 3 the problem of nuclei is generally disposed of by the assumption that nuclei are available in all orientations; the theory then has to explain the final texture from the initial texture and the way boundary mobility depends on orientation. In the oriented nucleation theory of texture formation"' nuclei are considered to be present only in certain orientations but the importance of growth selectivity is still recognized. For example, the mobility of boundaries of approximately the same orientation and of the coherent type in twins is believed to be low while that of high-angle boundaries, in general, is high. Because of this the theory may be described as an oriented-nucleation growth-selectivity theory. The main feature of the oriented-nucleation theory, however, is the importance given to nuclei; i.e., how they form in specific orientations and how they grow. In the present investigation two cold-rolled single crystals were used to study the effects of growth after primary recrystallization. The cold-rolled textures and the primary recrystallization textures were determined from portions of these specimens and reported earlier.",' The two cold-rolled crystals were in the (111) [112] stable end orientation, the recrystallization textures were nearly identical and consisted of two strong components, designated M and M', which were near (120) [00l] and (320) [00l], respectively, and also some specific weak components near (111) [110] and (111) [110]. It is well recognized that a single strong component in the primary recrystallization texture may be needed for secondary recrystallization3, 5, 8 but unfortunately when this is the case the amount of material left in deviating orientation may be too small either for growth or for positive identification. The present samples proved to be almost ideal for the study of minor components and their influence on texture changes produced by growth after primary recrystallization. The results obtained are interpreted in terms of present knowledge of grain-growth processes. Experimental Procedure Two lots of silicon-iron alloy of essentially the same composition, namely, 3.25 pet Si, 0.004 C, 0.009 P, 0.010 S, 0.035 Mn, 0.070 Ni, 0.090 Cu, 0.009 Sn, with traces of A1 and Cr and the balance Fe, were converted into single crystals 0.025 in. thick and 1.25 in. wide. The orientations were predetermined by the method of reorienting a seed crystal as described elsewhere.3 pecimen 1 from one lot had the (335) [556] orientation while specimen 2 from the second lot had the (111) [112] orientation.* Both crystals were cold rolled to a reduction in thickness of 70 pet while widening approximately 20 pet. Samples of each were selected for determining 1) the cold-rolled texture, 2) the time required at

Jan 1, 1959

By F. D. Rosi, C. A. Dube, B. H. Alexander

The slip and twinning planes have been determined in deformed crystalsof titanium by an X-ray method of analysis. The slip planes are of the type {1010} and {1011}, while the twinning planes are of the type {1072}, {1121}, and (1122). In the case of the predominant (1010) slip, a type I digonal axis of indices <1120> was the effective slip direction. Microscopic observations on the appearance of the three twin types disclosed a distinct difference in their shapes, and an attempt was made to correlate this difference with the amount of twinning shear. The slip mechanism was discussed on the basis of the difference in c/a ratios for the common hexagonal close-packed metals. IT is a general rule that slip in metals occurs most easily on the planes of greatest atomic density and of the largest interplanar spacing, and that the direction of slip is a close-packed direction. Thus, of the hexagonal close-packed metals which have been investigated by the German school in the decade 1925 to 1935 (cadmium, zinc, and magnesium), it has been found that slip occurs on the basal plane (0001) and in a <1120> direction.&apos; In the case of magnesium above 225oC, slip occurs on a first-order pyramidal plane (1011) as well as on the basal plane.&apos; The hexagonal metals, moreover, deform in part by twinning, and, again with the exception of magnesium at elevated temperatures, the twinning plane has always been reported to be a second-order pyramidal plane {1012).&apos; In view of this consistency in the plastic behavior of these metals, it has been supposed that the same slip and twinning elements would be operative in the other important hexagonal close-packed metals (titanium, zirconium, and beryllium), although there are some reasons why this may not be so. Referring to the tabulation in Table I of the axial ratios of the important metals in this structural class, it may be seen that they can be categorized into three distinct groups depending on the value of their c/a ratios. In the first group are cadmium and zinc with large positive deviations from the ideal ratio for closest packing. This expansion in the direction of the c-axis would be such as to accentuate the basal plane as the slip plane, because it increases the interplanar spacing. The second group includes cobalt and magnesium, which closely approximate the ideal ratio. In the third group are zirconium, titanium, and beryllium whose axial ratios are decidedly less than the ideal. The lattice of the elements in this group is compressed along the c-axis which, in effect, tends to make the basal plane less favorable for slip inasmuch as it reduces the interplanar spacing and the atomic density of this plane. Thus, for metals in the third group, it may be said that there is a certain indefiniteness about the glide plane, in that planes other than the basal plane may be expected to operate. The fact that magnesium begins to exhibit planes other than the normal slip and twinning planes at elevated temperatures may indicate that this behavior will become more pronounced in metals of lower axial ratios. For this reason it might be expected that the slip and twinning behavior of zirconium, titanium, and beryllium would be different from that found in cadmium and zinc. One indication that there is a difference is reflected in the recent work which has been done on the deformation textures of these metals."&apos; As will be shown later, there is a significant difference between the rolling textures of cadmium, zinc, and magnesium on the one hand, and zirconium, titanium, and beryllium on the other, and this difference suggests that the mechanism of plastic flow is not the same in these two groups of metals. From these considerations, therefore, it may be seen that there are good reasons why it cannot be concluded that titanium will have the same crystal-lographic elements of slip and twinning as those exhibited by zinc and cadmium. For the complete determination of these elements it would be most advantageous to have single crystals. However, much valuable information can be obtained by using coarse grained polycrystalline specimens, provided the grains are sufficiently large to permit X-ray

Jan 1, 1954

Edward Keller, Baltimore, Md. (communication to the Secretary*) :—The authors of this paper are to be commended for their industry and congratulated upon the many interesting results which were the fruit of their researches. While thoroughness has marked their work in general, yet on a few points in particular they have touched but lightly, for which reason, it would appear to me, they have hit wide of the mark in their respective conclusions. The work alluded to pertains chiefly to the occurrence of magnetic iron oxide (ferroseferric oxide) in copper-mattes. Because the authors find that the magnetic residue, left by the dissolved sulphides, varies largely in quantity according to the strength of nitric acid used (with potassium chlorate) in dissolving the mattes, they conclude :— "It appears, therefore, that the ferroso-ferric oxide is the result of precipitation by the oxidizing agent, rather than an original constituent of the matte." In this part of their investigation, Messrs. Gibb and Philp have ignored some well-established data,. In the first place, they have overlooked the fact that there are mattes which are strongly magnetic and others which scarcely show any magnetic property. There is nothing in their work tending to explain this variation. They Seem to have tested none of their products for magnetism. Secondly, they have overlooked the fact that magnetic iron oxide probably exists in all ore-charges in the copper-matting furnaces, and, under the given conditions, that this oxide is very difficult to reduce and to combine with silica to form slag. Thirdly, they pay no attention to the varying specific gravity of the several grades of copper-matte, which may exceed, equal, or fall below that of the magnetic oxide. These are .essential points which, I believe, clearly in-

Jan 1, 1906

By C. A. Heiland

I. Description of reflection equipments.................. 412 A. Design features of present types.................. 412 B. Reflection equipment designed by writer.............. 418 11. Characteristics of reflection seismographs............... 421 A. Types of coupling in electromagnetic seismographs.......... 421 B. Action of pickup, amplifier and galvanometer............. 424 C. Combined action of pickups, amplifiers and oscillographs....... 433 D. Static and dynamic constants................... 434 E. Desirable values for static and dynamic constants.......... 435 111. Calibration of reflection apparatus.................. 442 A. Dynamic tests without shaking table................ 442 B. Calibration methods....................... 445 C. Various other tests........................ 451 INTRODUCTION In the past five years, the reflection method of seismic prospecting has been developed to a high degree of perfection. Its success in mapping oil structure is due to the unique and definite nature of the depth data obtained. While articles on the principle and results of this method continue to appear in increasing number, there is virtually nothing published about the instruments used in this work. Several years ago, the writer started an experimental and theoretical investigation with the object of determining which characteristics would be best adapted to the problem at hand. As a result, an equipment was developed which has proved its usefulness in a great number of field tests. W. E. Pugh, now with the Empire Oil and Refining Co., joined the writer, in 1931 and 1932, in the laboratory experiments and field tests. In 1933, a paper was written on Certain Instrument and Field Problems in Reflection Seismology, and submitted to the Institute. The part of that paper dealing with field tests was published as Contribution 34 (reprinted in this volume, p. 455). Since then, considerably more labora-

Jan 1, 1934

By Janshi Sen

Vertical-intensity magnetometers, for instance the Hotchkiss Superdip and the Askania vertical field balance, are now widely used, because vertical-intensity charts give definite information for the location of upper pole, dip and strike, and approximate shape of the deposit. Again, a slow and steady increase of dip over a large area indicates a large deep-lying deposit, while a large dip limited to a small area and falling away rapidly suggests a small and shallow one. The complication comes more from the richness of the ore. A large body of lean ore near the surface might produce the same vertical-intensity chart as a rich ore at depth. This paper presents a method for calculating the maximum depth of a single-pole deposit and another for a two-pole mineral body, by utilizing data of both vertical and horizontal intensities as obtained by a Thalen-Tiberg magnetometer. As shown on the left side of Fig. I, lean ore, rich ore and a single pole produce the same magnetic field. The depth of the pole, where G is the vertical intensity at point A due to the pole; F, the horizontal intensity of the same; and a, the distance from the point of maximum vertical intensity or the vertical projection of the pole on the surface to the point of observation A. If an entirely covered deposit is indicated by magnetic measurements and boring cost estimated from the calculated depth is so reasonable as to encourage drilling, the ore should be struck somewhere within the limit of the calculated depth by the borehole. A number of such points as A should be taken for calculation, erratic results should be rejected and the average figure used for cost estimation.

Jan 1, 1946

By Janshi Sen

Vertical-intensity magnetometers, for instance the Hotchkiss Superdip and the Askania vertical field balance, are now widely used, because vertical-intensity charts give definite information for the location of upper pole, dip and strike, and approximate shape of the deposit. Again, a slow and steady increase of dip over a large area indicates a large deep-lying deposit, while a large dip limited to a small area and falling away rapidly suggests a small and shallow one. The complication comes more from the richness of the ore. A large body of lean ore near the surface might produce the same vertical-intensity chart as a rich ore at depth. This paper presents a method for calculating the maximum depth of a single-pole deposit and another for a two-pole mineral body, by utilizing data of both vertical and horizontal intensities as obtained by a Thalen-Tiberg magnetometer. As shown on the left side of Fig. I, lean ore, rich ore and a single pole produce the same magnetic field. The depth of the pole, where G is the vertical intensity at point A due to the pole; F, the horizontal intensity of the same; and a, the distance from the point of maximum vertical intensity or the vertical projection of the pole on the surface to the point of observation A. If an entirely covered deposit is indicated by magnetic measurements and boring cost estimated from the calculated depth is so reasonable as to encourage drilling, the ore should be struck somewhere within the limit of the calculated depth by the borehole. A number of such points as A should be taken for calculation, erratic results should be rejected and the average figure used for cost estimation.

Jan 1, 1946

By Wm. Hamilton Merritt

With the exception of the Vancouver Island coal, all the western coal-fields owe their present development to the completion, in the autumn of 1886, of the Canadian Pacific railroad. While it could not be expected that a very great deal could be accomplished in three years, enough has been done to pretty thoroughly establish the coal-bearing areas and their correspondence with those which have been developed to the south of the boundary along the lines of the transatlantic railroads in the United States. This summer I visited some of the important developments in the coal areas of Washington Territory, largely with the object of being better able to appreciate the corresponding coal-bearing areas in British Columbia to the north. In Western Canada, coal-bearing rocks have been found in three zones: 1. In the plains to the east of the Rocky Mountains and in the eastern flanking ranges, the coal occurs in the Cretaceous formation (including the Laramie). 2. In the interior plateau of British Columbia, the coal is found in the Tertiary formation. 3. On the coast of British Columbia, Cretaceous and Tertiary rocks are found carrying coal, and on the Island of Vancouver the well known Nanaimo coal has been worked for years in the first named formation. In all of these zones, the coals vary from lignites up to higher grades, the factor determining quality being the amount of pressute to which they have been subjected. The intensity of this pressure is generally shown by the disturbance which the coals exhibit, and, in many cases, is almost directly in proportion to the distance of the deposits from mountain ranges. This seems to be also the opinion expressed by Mr. Bailey Willis in connection with his Census Report on the coals of Washington. It has been elsewhere stated

Jan 1, 1890

By John E. Conley

The production of lime by the burning or calcination of limestone, including all varieties from true dolomites and magnesian limestones to high-calcium types, continues as one of the essential basic industries. In 1937, a total of 4,124,165 tons of lime valued at approximately $30,091,000 was produced in the United States.&apos; The importance of any contribution to our knowledge on the mechanism of the lime-burning process is, therefore, obvious. The burning of limestone has been practiced since the earliest days of our civilization, and the literature on the various phases of the industry is voluminous. Calcination of the various types of limestone has been studied by many previous investigators, but some points require additional research. Each occurrence of limestone provides an opportunity for specific investigation, because the characteristics of stones in different localities vary. Knibbs13 has given an excellent discussion of available data on the theory of lime and magnesia burning. The thermal dissociation of calcium carbonate has been studied more recently by Johnstonr2 Smyth and Adams,3 Ralston et al.,4 Furnas,6 Potapenko,6 and Southard and Royster.7 As a result of these investigations the dissociation temperature at atmospheric pressure has been established as 894" to 898&apos; C. The dissociation of dolomite and magnesite, although studied by several investigators,4,6,8 still requires clarification by additional data. The calcination of limestone was studied for a twofold purpose: (I) to extend our information on the mechanism of the lime-burning process and (2) to standardize the conditions for calcination of high-calcium and dolomitic limestones for subsequent hydration tests on the lime.

Jan 1, 1942

By John E. Conley

The production of lime by the burning or calcination of limestone, including all varieties from true dolomites and magnesian limestones to high-calcium types, continues as one of the essential basic industries. In 1937, a total of 4,124,165 tons of lime valued at approximately $30,091,000 was produced in the United States.&apos; The importance of any contribution to our knowledge on the mechanism of the lime-burning process is, therefore, obvious. The burning of limestone has been practiced since the earliest days of our civilization, and the literature on the various phases of the industry is voluminous. Calcination of the various types of limestone has been studied by many previous investigators, but some points require additional research. Each occurrence of limestone provides an opportunity for specific investigation, because the characteristics of stones in different localities vary. Knibbs13 has given an excellent discussion of available data on the theory of lime and magnesia burning. The thermal dissociation of calcium carbonate has been studied more recently by Johnstonr2 Smyth and Adams,3 Ralston et al.,4 Furnas,6 Potapenko,6 and Southard and Royster.7 As a result of these investigations the dissociation temperature at atmospheric pressure has been established as 894" to 898&apos; C. The dissociation of dolomite and magnesite, although studied by several investigators,4,6,8 still requires clarification by additional data. The calcination of limestone was studied for a twofold purpose: (I) to extend our information on the mechanism of the lime-burning process and (2) to standardize the conditions for calcination of high-calcium and dolomitic limestones for subsequent hydration tests on the lime.

Jan 1, 1942

By H. E. N. Stone, B. L. Daniell

This paper examines the cracking behavior on chemical reduction of three types of ore/oxide briquette mixtures. The complex sintering/hardening atmosphere was replaced by 100% oxygen and the blast furnace atmosphere by a 5/95 hydrogedsteam mixture which was used isothermally at 700°C for a constant, arbitrary time. Cracking has been assessed by measurement of reduction expansion or increase in specimen diameter as a result of chemical reduction and a subjective index based on appearance and friability. Oxidized briquettes of iron ore concentrate crack on reduction&apos;-3 in a manner which parallels the degradation of sinter in the Linder test. In the present work, the cracking behavior on chemical reduction of three types of ore/oxide briquette mixture has been studied. Firstly, LD converter fume with additions of silica; secondly, Oxfordshire ore with ferric oxide; thirdly, ferric oxide with separate additions of silica, alumina and lime. Motivation for the first-mentioned experiments lay in the improvement of the fume as furnace feed; for the second, in assessing the tolerance of a finely divided ferric oxide as a base for low melting point additions. The third series provided additional information. In this work, the complex sintering/hardening atmosphere is replaced by 100% oxygen and the blast furnace atmosphere is replaced by a 5/95 hydrogen/ steam mixture used isothermally at 700°C for a constant arbitrary time. The particular reduction conditions were known from previous experience3 to be capable of disclosing any tendency to cracking. Cracking has been assessed by measurement of reduction expansion (i.e., increases in specimen diameter as a result of chemical reduction) and a subjective index based on appearance and friability. Generally

Jan 1, 1970