Search Documents

By E. A. Nichols

The purpose of this paper is to present a contour map that shows the geographical variation in geothermal gradients in the Mid-Continent and Gulf Coast oil fields. Introduction Frequently there arises the need for an estimation of the temperature to be expected at a predetermined depth in working with a wildcat or in deepening old production into 'Ones that are relatively unknown. The study of geothermal gradients in oil fields has been made previously by many investigators. One of the pioneers in this work was C. E. Van Orstrand,' who, as well as most of the other investigators, was primarily interested in the relation between temperature and depth in a given locality. Between 192r and 1929, American Petroleum Institute Research Project NO. 25 fostered a thorough study of earth temperatures.2 K. IV. French did some work in California, the results of which were published in 1939.3 In most of these studies, an attempt was made to correlate temperatures in a rather localized area. This paper will show the results of an attempt to correlate temperature gradients over rather large Portions of the Mid-Continent and Gulf Coast area. Method of Obtaining Data It has been found that for complete thermal equilibrium to be established in a well, the well must stand undisturbed for a period of several hours to several weeks, depending upon the way the well was produced prior to the shut-in period. The data in this paper were obtained in conjunction with running pressures in wells or in taking samples of reservoir fluid. Glass maximum recording thermometers were used in all but a few instances. The wells had been shut in from one hour up to I. or 12 days. Since the wells were normal producing wells, some of the shut-in times undoubtedly were insufficient for complete thermal equilibrium to have been established and the temperatures measured do not necessarily represent the true earth temperatures. They do represent the temperature conditions that will be encountered in a well that is producing oil. The data, therefore, can be useful in working with or in estimating the temperatures to be expected in producing reservoirs. In obtaining a thermal gradient by dividing the difference in temperature of the formation and the mean annual surface temperature by the depth of the formation, one is assuming the depth-temperature line to be straight. Depth-temperature curves are almost straight lines (Fig. I). However, on close examination of accurate data, a slight curvature usually is observed. Most wells yield curves with slopes increasing with increasing depth. These curves are believed to be from wells that are in and are underlain by sedimentary material. Some few curves have slopes that decrease with increasing depth. These curves are believed to be from wells that are underlain rather closely by granite or some other igneous rock. Most investigators

Jan 1, 1947

By E. A. Nichols

The purpose of this paper is to present a contour map that shows the geographical variation in geothermal gradients in the Mid-Continent and Gulf Coast oil fields. Introduction Frequently there arises the need for an estimation of the temperature to be expected at a predetermined depth in working with a wildcat or in deepening old production into 'Ones that are relatively unknown. The study of geothermal gradients in oil fields has been made previously by many investigators. One of the pioneers in this work was C. E. Van Orstrand,' who, as well as most of the other investigators, was primarily interested in the relation between temperature and depth in a given locality. Between 192r and 1929, American Petroleum Institute Research Project NO. 25 fostered a thorough study of earth temperatures.2 K. IV. French did some work in California, the results of which were published in 1939.3 In most of these studies, an attempt was made to correlate temperatures in a rather localized area. This paper will show the results of an attempt to correlate temperature gradients over rather large Portions of the Mid-Continent and Gulf Coast area. Method of Obtaining Data It has been found that for complete thermal equilibrium to be established in a well, the well must stand undisturbed for a period of several hours to several weeks, depending upon the way the well was produced prior to the shut-in period. The data in this paper were obtained in conjunction with running pressures in wells or in taking samples of reservoir fluid. Glass maximum recording thermometers were used in all but a few instances. The wells had been shut in from one hour up to I. or 12 days. Since the wells were normal producing wells, some of the shut-in times undoubtedly were insufficient for complete thermal equilibrium to have been established and the temperatures measured do not necessarily represent the true earth temperatures. They do represent the temperature conditions that will be encountered in a well that is producing oil. The data, therefore, can be useful in working with or in estimating the temperatures to be expected in producing reservoirs. In obtaining a thermal gradient by dividing the difference in temperature of the formation and the mean annual surface temperature by the depth of the formation, one is assuming the depth-temperature line to be straight. Depth-temperature curves are almost straight lines (Fig. I). However, on close examination of accurate data, a slight curvature usually is observed. Most wells yield curves with slopes increasing with increasing depth. These curves are believed to be from wells that are in and are underlain by sedimentary material. Some few curves have slopes that decrease with increasing depth. These curves are believed to be from wells that are underlain rather closely by granite or some other igneous rock. Most investigators

Jan 1, 1947

By Jr. D. C. Williams, D. V. Carter

The four new oil-field discoveries made in the East and East Central Texas districts during 1941 were the East Long Lake field, Anderson County; Pickering field, Shelby County; Pleasant Grove field, Rusk County, and Tri-Cities field, Henderson County. The discovery of oil production in the Pettit lime of the Lower Glen Rose was made in the Groesbeck (Barron) field in Limestone County and the Willow Springs field in Gregg County. Important extensions were made to the Pittsburg field, in Camp County, the Chapel Hill field, in Smith County, and the Hawkins field, in Wood County. The Hawkins field was extended sufficiently to more than double the number of proved surface acres. As usual the East Texas field led the district in the number of completions for the year. The second most active field during the year was the Hawkins field, with 250 new wells completed. The third most active was the Long Lake field, in which 50 wells were completed. Approximately 964 wells were completed in the district during 1941. Production and Probation The district is credited with having produced 163,566,695 bbl. of oil and distillate during the year. This represents a decrease of 4 per cent from the 170,424,685 bbl. of oil and distillate produced during the preceding year. The production of 130,378,620 bbl. of oil and distillate from the East Texas field represents 79.7 per cent of the total production of the district; that is, 6.3 per cent less than the production for the year 1940, The district had an estimated basic daily allowable of 614,982 bbl. of oil on Dec. 31. Approximately 33 per cent of the state's annual production was produced in the district, compared with 34.9 per cent for 1940. Since the majority of the fields in this district are subject to proration, any change in the annual production is attributable largely to changes in proration schedules and number of shutdown days. Fields subject to shutdown days were closed in for 113 days during the year, with the exception of the East Texas field, which was shut down 111 days. An order was promulgated by the Oil and Gas Division of the Texas Railroad Commission for encouraging the disposal of salt water and reservoir-pressure maintenance in the East Texas field. Discoveries Tex Harvey Oil Company'sNo. I S. E. J. Cartmel was completed as the discovery well for the East Long Lake field, Anderson County. Production was found in the Woodbine sand, the horizon from which the Long Lake field produces. The Pickering field, Shelby County, secures its production from the Nacatoch sand, found at an approximate depth of 1510 ft., in A. E. McKiernan's No. I, Pickering Lumbering Co. This field is in an area near the state line in which a number of relatively unimportant and

Jan 1, 1942

By Jr. D. C. Williams, D. V. Carter

The four new oil-field discoveries made in the East and East Central Texas districts during 1941 were the East Long Lake field, Anderson County; Pickering field, Shelby County; Pleasant Grove field, Rusk County, and Tri-Cities field, Henderson County. The discovery of oil production in the Pettit lime of the Lower Glen Rose was made in the Groesbeck (Barron) field in Limestone County and the Willow Springs field in Gregg County. Important extensions were made to the Pittsburg field, in Camp County, the Chapel Hill field, in Smith County, and the Hawkins field, in Wood County. The Hawkins field was extended sufficiently to more than double the number of proved surface acres. As usual the East Texas field led the district in the number of completions for the year. The second most active field during the year was the Hawkins field, with 250 new wells completed. The third most active was the Long Lake field, in which 50 wells were completed. Approximately 964 wells were completed in the district during 1941. Production and Probation The district is credited with having produced 163,566,695 bbl. of oil and distillate during the year. This represents a decrease of 4 per cent from the 170,424,685 bbl. of oil and distillate produced during the preceding year. The production of 130,378,620 bbl. of oil and distillate from the East Texas field represents 79.7 per cent of the total production of the district; that is, 6.3 per cent less than the production for the year 1940, The district had an estimated basic daily allowable of 614,982 bbl. of oil on Dec. 31. Approximately 33 per cent of the state's annual production was produced in the district, compared with 34.9 per cent for 1940. Since the majority of the fields in this district are subject to proration, any change in the annual production is attributable largely to changes in proration schedules and number of shutdown days. Fields subject to shutdown days were closed in for 113 days during the year, with the exception of the East Texas field, which was shut down 111 days. An order was promulgated by the Oil and Gas Division of the Texas Railroad Commission for encouraging the disposal of salt water and reservoir-pressure maintenance in the East Texas field. Discoveries Tex Harvey Oil Company'sNo. I S. E. J. Cartmel was completed as the discovery well for the East Long Lake field, Anderson County. Production was found in the Woodbine sand, the horizon from which the Long Lake field produces. The Pickering field, Shelby County, secures its production from the Nacatoch sand, found at an approximate depth of 1510 ft., in A. E. McKiernan's No. I, Pickering Lumbering Co. This field is in an area near the state line in which a number of relatively unimportant and

Jan 1, 1942

By Fred C. Bond

Many grindability tests have been made in the Allis-Chalmers laboratory since the tabulated results were last published.' The lists of standard ball-mill and standard rod-mill grindability tests are brought up to date in this paper, and considerable new material is added. This includes a tabulation of open-circuit grinding tests, with impact and compression-crushing tests. The standard ball-mill grindability tests (Table I) were made in a standard laboratory ball mill, 12 by 12 in. inside, running at 70 rpm, with a charge of 285 iron balls ranging from 1½ to 3/4 in. in diameter and weighing 20,125 grams. Seven hundred cubic centimeters of minus 6-mesh stage-crushed dry feed was used, and the circulating load was maintained constant at 250 pct by adjusting the number of mill revolutions for each grinding period. Tests were made at all mesh sizes from 28 to 200, and the grindability is the number of net grams of screen undersize produced per revolution. The table includes 479 tests. It has been calculated that the ball mill does 52.3 joules of useful work on the ore per revolution2 with 93 joules input to the mill. The standard rod-mill grindability tests (Table 2) were made in a laboratory tilting rod mill, 12 in. in diameter by 24 in. long inside, with a wave-type lining, running at 46 rpm. The grinding charge consisted of six I1/4-in. diameter and two 13/4-in. diameter steel rods, all 21 in. long and weighing 33,380 grams. The mill was rotated level for eight revolutions, then tilted up 5' for one revolution, down 5° for one revolution, and returned to level for eight revolutions. It was discharged by tilting downward at 45° for 30 revolutions. Feed consisted of 1250 cc of minus in. stone and the circulating load was maintained constant at 100 pct by adjusting the number of mill revolutions for each grinding period. Tests were made at all mesh sizes from 3 to 65, and the rod-mill grindability is the number of net grams of screen undersize produced per revolution. The table includes 105 tests. The impact and compression-crushing tests (Table 3) are given in a table that is an extension of a previous publication8 in which the method of testing was described in detail. Two equal hammers weighing about 30 lb each were arranged to strike simultaneous blows on opposite sides of the test specimen. Broken pieces of rock passing a 3-in. square and retained on a 2-in. square were set up with the smallest dimension between the hammers, and this distance was measured. The height of the hammers was increased slightly before each blow until the specimen broke, and the foot-pounds per inch of thickness was calculated. Ten pieces

Jan 1, 1949

By Stanley D. Michaelson

THE selection of the proper size of grinding mill for a given installation has long been a subject of discussion by mill manufacturers, consulting engineers, and their clients. It would be presumptuous for the author to propose a simple cure-all. Instead this paper describes a method that has been used over a period of years to determine mill size with a reasonable degree of accuracy. Furthermore, this method claims no theoretical background, for ball milling, as practiced today, is still an art. The selection of the proper size and type of mill must, therefore, be made on an empirical basis. A ball mill, in order to grind, must deliver power through its grinding media to the material to be ground. Assuming that a mill is properly supplied with grinding media, ore pulp, and power, the amount of grinding done is closely proportional to the power expended. With this as a basic premise we can, for the moment, forget about type of mill (i.e., overflow, low-level mill, or other design) and base our calculation of mill size on the total power required to grind a ton of a particular ore from a given size of feed to a given size of product. When this is determined the type and size of mill, its speed, and the weight of the load of grinding media can be selected to absorb this amount of power. DEVELOPMENT OF TECHNIQUE Some years ago, W. L. Maxson, F. Cadena, and F. C. Bond, working in the Minerals Research Laboratory of Allis-Chalmers Co., Milwaukee, developed and described a laboratory technique for comparing grindability (or relative ease of grinding) of various ores at different mesh sizes of grind.1 Additional papers2 have described the work done since that time, and the most recent paper3 summarizes results for hundreds of tests on many ores and materials. The essentials of the testing method are: a I a by 12-in. laboratory mill operating at a constant speed of rotation, using a constant volume of ore, and a constant ball load having a relatively constant grinding surface. Tests are run at 250 per cent circulating load with the feed, circulating load and products screened on calibrated Tyler standard screens. Certain ores from operating mills, representing various mineralogical types, were selected for reference and designated "standard ores." In most cases, detailed studies of the grinding circuits were made when samples of mill feed were taken for grindability tests. Each analysis formed a basis for comparison of the grindability in the laboratory with actual power requirements for a particular grinding circuit. In addition, a critical study was made, to evaluate the differences in the various grinding circuits so that two or more field installations having different layouts (single-stage grinding, two-stage grinding, or others), and using mills of various diameters operating at various speeds with differing circulating loads, etc., could be compared. Large-scale tests by mill operators complemented by laboratory investiga-

Jan 1, 1945

By J. W. Marx

A method is given for predicting the complete gravity drainage characteristics of arbitrarily long columns from centrifuge drainage measurements on reconstituted core samples. Oil residuals corresponding to hundreds of years of normal gravity depletion can be obtained in a few hours on the centrifuge. The gravity flow rate at any stage of the depletion process may be determined from the time correlation derived, and experimentally checked, in this study. INTRODUCTION Apart from the original observations of Muskat et al1, research publications2,3,4 on the subject of gravity drainage have been largely concerned with establishing in detail the saturation, S as a function of the height, z, in a draining column at any given time, t. Some form of numerical integration must be employed to obtain production rates and cumulative production even when S(z, t) is known. Furthermore, the relevant experimental work has been concentrated on drainage of a single wetting liquid from unconsolidated media. Since oil production usually concerns the drainage of a partially wetting liquid from consolidated media, in the presence of connate water, and since it is unlikely that sufficient information exists to establish S(z, t) in detail for any natural reservoir, the published research work appears to be, at best, only qualitatively applicable to production problems. With this in mind, the present study was undertaken by the writer. Experiments were planned whose results would have two advantages over existing measurements: 1. Observations were to be made on specific reservoir rock, reconstituted with formation water and formation oil. This would reduce their generality, from the research viewpoint, but increase their utility for production purposes. 2. The measurements were to be self-integrating, i.e., the phenomena were to be described and interpreted in terms of cumulative results. THEORETICAL DEVELOPMENT It was commonly known that centrifuging a liquid bearing porous medium increases the drainage rates and minimizes capillary end effects. The specific problem lay in selecting an acceleration, a, such that the mean residual saturation of a model cylinder was equal to the residual saturation of an arbitrarily long prototype column when the latter was drained by earth gravity alone. The physical conditions required to permit a valid scaling of model drainage time, tm with prototype drainage time, t, may be stated as follows: (a) At t = tm = O, So = Smo; (b) At t = tm? 8 Sr. = Smr.; (c) For all intermediate values of t and dS/dt=dsm/dtm whenever S = Sm; (d) S(z) = Sm(z) = a constant when t = tm = 0. 1 Here S = T I S(z)dz, where h is the length of the « Jo cylindrical column being drained and the subscripts S,Sm, and refer to model, initial, and residual systems, respectively. The first three conditions mean, simply, that an 3 vs t plot will be numerically identical with an S, vs t, plot,

Jan 1, 1957

By R. T. Hukki

The purpose of this paper is to present an analysis of the unit operation of grinding and the circulating load, of the unit operation of classification and the circulating load, and of the two superimposed into one operation to clarify the overall trend of events relating the circulating load to the capacity of the closed circuit grinding system, to the specific surface area of the final fine product, and to the energy consumption in the closed circuit grinding process. The capacity of the closed circuit is frequently, if not always, determined by the classifier, not by the mill." With these words a startling idea was expressed in 1934 by Dorr and Anable.1 Today, some 30 years later, grinding in closed circuit is universally accepted. The basic curve presenting the capacity factor versus circulating load by Dorr and Anable has obviously been so convincing that not a single authoritative investigation regarding its validity seems to have been conducted. The only major subject of discussion appears to have been the relative merits of the 'high' and 'low' circulating loads. It seems to be universally agreed that much still remains to be hoped for regarding sharpness of classification. BASIC CURVES FOR CONSTANT MILL LOADING Fig. 1 presents a series of basic curves for constant mill loadings in function of new feed rate and circulating load. The mill loading indicated by each curve is the sum of hourly tonnages of new feed and circulating load. For example, at point 0 where the new feed rate is 100 t/h and the circulating load 300%, or 300 t/h, the mill loading is 400 t/h. In closed circuit grinding, the new feed rate corresponds to the rate of finished classified material produced. Although at this stage the effect of classification is excluded in construction of the basic curves, the trend indicated by these curves is strongly in favor of closed circuit operation under relatively small circulating loads. A study of the curves reveals that, e.g., a mill operating under a load of 200 t/h at point P where the new feed rate is 50 t/h and the circulating load 300% will also operate under the same total load at point Q where the new feed rate is 100 t/h and the circulating load 100%. In other words, a reduction of circulating load from 300% to 100% would lead to doubling of the new feed rate and doubling of the rate of production of finished material, without a change in the total mill loading. The obvious question is, is it also possible by a reduction of the circulating load in a closed industrial grinding circuit to increase the production of finished classified material and, if so, how and to what extent? GRINDING TESTS BY DORR AND ANABLE In a series of open circuit grinding tests reported by Dorr and Anable1 limestone was ground at various feed rates in a 3-ft ball mill. The original data are reproduced in Table I. It can be seen that with the increased feed rate production of -65-mesh material increased and the energy consumption per unit weight of the -65-mesh product decreased in the reverse ratio. The data shown in Table I have been reproduced for our purposes in Table II for a scale corresponding to grinding in a large industrial mill. This reproduction

Jan 1, 1968

By F. B. Plummer

PERHAPS the greatest progress made in the technical methods of oil production during the last year has been in handling gas from the new fields that yield light distillate fractions. At least sixteen recycling plants have been perfected and installed in South Texas fields alone during 1939 having a daily capacity of more than one billion -2 cubic feet of gas and capable of producing more than a million gallons of distillate daily. The process consists of running the gas under pres- sure through especially designed plants, separating out the condensate, then compressing the gas to 3000 lb. or more, depending on the subsurface pressure in the formation, and injecting gas back into the reservoir to be produced again later, along with more of the liquid hydrocarbons, and again recycled. Hence production in these distillate fields in sense has changed from that of producing a constantly diminishing and much-wasted product to a more or less continuous manufacturing process, in which practically all the gas is conserved-a real triumph in engineering practice.

Jan 1, 1940

By Karl W. Mote

CALIFORNIA'S iron and steel industry had its beginning in San Francisco in 1849 when the first iron casting was poured at the old Union Iron Works. Soon after, in 1856 at Grass Valley, enough iron ore was smelted to supply pig iron for the castings of a quartz mill there. From 1880 to 1886, iron ore was produced from the Hotaling mine in Placer County and converted to pig iron in a local blast furnace using charcoal. From 1907 to 1914, the Noble Electric Steel Co. produced pig iron from iron ore mined at the Shasta Iron Co. mine, and followed this for three years in the production of ferro-alloys. Between 1917 and 1941, the State's industry in- creased its capacity for open hearth and electric furnace scrap treatment, but the real impetus was supplied by the need for more steel at the beginning of World War II. The result was the State's first integrated steel plant-the Kaiser Steel Corp. facilities at Fontana.

Jan 7, 1958

By Charles E. Wait

In the use of the apparatus purchased for the new chemical laboratories of the university, no piece has given us more satisfaction, or has been a greater success, than a new still which is the subject of this paper. In the designing of this still I had two definite objects in view ; one, the utilizing of steam from the large 60 horse-power boiler used in heating the building, and the other, a provision for making distilled water with gas, when steam from the heating-plant was not available. The still is encased in wrought-iron, with a lining of asbestos, and is provided with a float which automatically regulates the flow of water from the supply-pipe. It was made for me by G. J. M?rrle, Pforzheim, Germany, and was imported by Messrs. Eimer & Amend, of New York City. It is a beautiful piece of apparatus, and the workmanship is excellent in every detail. The essential parts of this apparatus will be understood by consulting the accompanying figures, but a few words of explanation may be appropriate. The still has a capacity of seven gallons, and is made of heavy copper, tin-lined. It has a water-gauge showing the height of the water in the still, also an exit for steam, and safetyvalve, V; inlet for steam through a coiled perforated block-tin pipe; also an outlet, 0, for cleaning out the still; and there is also a heavy

Jan 1, 1895

By H. Stuart, L. Zwell, N. Ridley

specimen that was subjected to 700°C for 250 hr is shown in Fig. 2(c). The precipitates in this foil appear round and exhibit only very faint strain contrast. From this evidence, along with that described above for the symmetry of the strain field, it may be concluded that this coherent precipitate is spherical, which is generally the favored shape for coherent precipitates when the lattice parameter mismatch is small.12 These observations are consistent with the assumption that this precipitate is the y' (Ni3Al, Ti) phase. y' is known to be spherical in the early stages of precipitation. It is fcc and is similar in composition to the matrix and thus would have contrast similar to that of the matrix as do these precipitates. Direct identification of the spherical precipitate did not prove possible because of its low volume fraction and small size. The results of this investigation suggest that the increases in yield strength and the decreases in elongation observed in 45-Fe 30-Ni 20-Cr alloys containing about 0.4 pct A1 and 0.4 pct Ti on prolonged aging at 550" to 700°C are very likely due to the presence of a coherent, spherical precipitate, thought to be y'. Mi-crohardness measurements indicated that the precipitation of semicoherent M23C6 resulted in some matrix hardening. However, this precipitation process occurs much more rapidly than the changes in mechanical properties at these temperatures. 1C. L. Clark, J. J. B. Rutherford, A. B. Wilder, and M. A. Cordovi: J. Eng. Power, 1962, vol. 84, p. 258. 2 F. A. Comprelli and U. E. Wolff: USAEC Report GEAP-4745, General Electric Company November, 1964. 3C. N. Spalaris: A Monograph, USAEC Report GEAP-4633, General Electric Company, July, 1964. THERE have been many X-ray investigations of the room temperature lattice parameters of austenite which has been retained in quenched steels of various carbon contents. The results of these investigations have been collected by Wrazej,1 Wever et al.,2 and by Roberts3 and are included in Fig. 1 due to Pearson.4 The dashed line in Fig. 1 was considered by Roberts3 to most reliably describe the variation with carbon content of the lattice parameter of retained austenite. This line is given by the equation: a (Å) = 3.555 + 0.044 wt % C and recent unpublished measurements by one of the authors (LZ) support this relationship. The object of this communication is to draw attention to a relationship which describes the variation of the room temperature lattice parameter of 'equilibrium' austenite with carbon content, and which is different from that for retained austenite. The relationship a(Å) = 3.573 + 0.033 wt % C has been obtained from lattice parameter measurements made on equilibrium Fe-C austenites at elevated temperatures, which have been extrapolated to room temperature. The room temperature lattice parameter of 3.555Å which the Roberts' relationship gives for pure y-Fe is no: in agreement with the value of 3.573Å obtained when the high temperature lattice parameter data of Basinski et aL.5 and of Goldschmidt6 is extrapolated to room temperature. A linear extrapolation was

Jan 1, 1970

By J. C. Allen, E. V. Herring

CHILE EXPLORATION CO's. oxide plant at Chuquicamata, the largest of its kind, started in 1915 with initial operations at the rate of 10,000 tons of ore per day. Anaconda Copper Mining Co. acquired the controlling interest in 1923 and in the next few years modernized the plant and mine, extending operations to a nominal capacity of 490 million lb of electrolytic copper yearly by 1942. Plant production averaging 495.7 million lb of copper per year was maintained for the eight-year period extending from 1941 to 1948 inclusive. During the World War II production reached its highest level when in 1944 the output was 531.8 million lb. The maximum production for any one month was 49.6 million lb, achieved in May 1947. E. A. Cappelen Smith, consulting metallurgist for M. Guggenheim's Sons, worked out the first process for the treatment of Chuquicamata copper oxide ore about 1913, and directed a staff of 20 young engineers operating a pilot plant at Perth Amboy, N. J., on three shifts for an entire year. The copper is extracted from the oxide ore by a hydro-metallurgical treatment described in detail by T. A. Campbell in AIME Transactions, Vol. 106, Copper Metallurgy, 1933. The Oxide Plant is divided into five main operations as follows: (1) Crushing, (2) Leaching, including dechloridizing and sulphur dioxide treatment, (3) Tailing disposal, (4) Electrolytic precipitation, (5) Smelting and melting. Crushing The present Primary Crushing Plant has been in operation 25 years, during which time 4,342,112 cars of 70 tons net capacity have passed through the dumpers. The ore as received from the mine is frequently blocky and up to 5 feet in section. It is reduced to 9-in. size by two 60-in. gyratory crushers, and transported to the east and west ore bins by 60-in. conveyors. In the secondary crushing operation the ore is first reduced to 2 to 3-in. size by five standard 7-ft cone crushers and two No. 10 gyratories. This product is then reduced to 3/8-in. size by fifty-two 48-in. vertical Symons disc crushers and is transported by belt conveyors to the loading bridges from which it is charged° into the leaching vats. Conveyor belt No. 14 which serves the eight vats in the east section of the leaching plant has transported over 125 million tons of ore, which is a record for any type of conveyor. This 60-in. belt travels at a speed of 600 fpm and carries loads up to 5500 tons per hr. Leaching The ore is leached in 14 vats, averaging 13,500 short tons net capacity each. These vats are lined with a natural mastic which adequately resists the sulphuric acid leaching solutions. The leaching process as presently conducted comprises soaking the ore with successive volumes of leaching solution and spent electrolyte and withdrawing successive volumes of enriched solution from the vat to a total of approximately 3.2 million gal. The first 1.6 million gal of this volume withdrawn is called strong solution and contains about 35 parts of copper per 1000. The balance of 1.6 million gal subsequently withdrawn is stored in a

Jan 1, 1952

By Evert Hoek

Summarising a conference is never an easy task, but I will try to keep my comments brief and to the point. There are a number of lessons which we have learned from our deliberations together during these past three days, and I will try to give you my impressions of these lessons and of their practical implications in open pit mining. The first thing that has become increasingly obvious during these discussions is that it is no longer acceptable to offer an 'Act of God' as an excuse for a major slope or tailings dam failure. Disasters such as that at Aberfan in the United Kingdom have focussed the world's attention on the activities of the mining industry and the report of the commission set up to investigate the Aberfan disaster clearly showed that adequate knowledge was available and that failure to apply this knowledge did not qualify as an 'Act of God'. The courts and the world's press are certain to impose increasingly harsher penalties and criticism on those held responsible for major failures, particularly of tailings dams, in the future. One of the major problems in applying available knowledge to slope problems is that attempts to apply this knowledge are frequently left too late. To provide an engineering solution in the case of a slope in an advanced state of failure is an almost impossible task, and it is essential that those responsible for the stability of a slope must learn to recognise signs of distress at an early enough stage for effective remedial measures to be taken. As our ability to solve slope problems improves, the time at which slope stability problems are considered in a mining project must move forward to a stage at which these problems can be anticipated and dealt with before they arise. Conferences such as this are important in that they enable us to exchange ideas and advance our knowledge to a level at which such predictive engineering will be possible. It has been encouraging to hear of mining projects such as the Bougainville Copper operation where slope stability studies were carried out as part of the overall evaluation programme and it is hoped that this will become a more common procedure in the future. Providing a safe slope in an opencast mine obviously costs money, either in terms of the reduced ore to waste ratio given by flat slopes or because of the cost of stabilization techniques such as drainage or the use of rock anchors. An optimum slope design will provide maximum safety at minimum cost but achieving this optimum is not an easy task. Any one of us could design a slope which would be stable to the end of time, but it is probable that that slope would be so flat as to be totally uneconomic in most open pit mining situations. On the other hand, if the overall economics of a mining project are so critical as to require slope angles which the engineer responsible for these slopes considers to be unsafe, it is his duty to make us could design a slope which would be stable to the end of time, but it is probable that that slope would be so flat as to be totally uneconomic in most open pit mining situations. On the other hand, if the overall economics of a mining project are so critical as to require slope angles which the engineer responsible for these slopes considers to be unsafe, it is his duty to make

Jan 1, 1971

By Henry R. Piehler

Continuous seven- and nine teen -filament close-packed silver-steel filamentary composites mere tested in tension. For purposes of comparison, the tensile behavior of the composite was predicted from the measured properties of the individual com-ponents. It was assumed that the axial strain is the same in both components and that the contribution of each component to the composite flow stress is proportional to its volume fraction. Good agreetnent was obtained between the observed and predicted tensile behavior. However, the composite elongation at fracture was about twice that observed when the individual steel wires were tested alone. Composites in which the filaments were widely spaced failed by the consecutive fracture of the filaments. In composites with closely spaced filaments, a composite instability preceded frachcre. These effects are explained in terms of a lateral restraint to the necking of the filaments which develops in the deforming composite. TWO-COMPONENT or composite materials are increasingly being developed and used as structural materials. Of all the composite geometries used, the filamentary configuration has proved to be the most successful. Polymer-bonded fiber-glas, the most common of the filamentary composites, has been investigated most extensively to date. One explanation of the behavior of fiberglas1 suggests that the load transfer between the glass fibers and the polymer matrix occurs primarily through friction. Bond separation between the fibers and the matrix is presumed to occur at very low stresses. Subsequently, only frictional bonding can provide for the transfer of load from the matrix to the fibers. The force normal to the fiber-matrix interface which gives rise to this friction is assumed to arise from the matrix shrinkage which occurs during solidification. The behavior of metallic filamentary-composite materials would be expected to differ from that of fiberglas in several significant aspects. Residual stresses resulting from differences in thermal contraction can be kept to a minimum by proper heat treatment. A strong wetted bond is formed between the two phases. In brazed joints,2 for example, the interphase bond is sufficiently strong that the weaker material will fail before separation occurs at the interface. Most metal filaments can undergo appreciable amounts of plastic deformation before failure. Failure by plastic instability or necking frequently occurs in metallic filaments, but not in glass fibers tested at room temperature. Differences between the behavior of fiberglas-polymer and metallic filamentary composites have indeed been observed in composites containing various types of metallic filaments in a silver matrix.3,4 At strains of the order of 10-2 pct, all the deformation was accommodated by the silver matrix. Hence, the strength of the composite depended only on the fiber concentration and not on the nature of the fiber. At higher strains, the strength of the composite increased when filaments with higher work-hardening rates were used. Surface slip line observations on a silver-mild steel composite that had been stretched 4 pct showed that an appreciable amount of deformation occurred in the filaments. Work on tungsten-copper filamentary composites5 has shown that the ultimate tensile strength for varying filament fractions followed a linear mixture rule. Assuming that the axial strains in both filaments and the matrix are equal, this linear mixture rule can be expressed as: The subscripts c, f, and m refer to the composite, filaments, and matrix, respectively. A and V are the area and volume fractions of each component. sc and of are the ultimate tensile strengths of the composite and the filaments. sm is the flow stress of matrix at a strain equal to the elongation at failure of the filaments. However, the tungsten filaments can undergo only a limited elongation before they fracture without an appreciable reduction in area. A composite containing more ductile filaments might indeed deviate from this linear mixture rule for the ultimate tensile strength, since filament failure by necking might be arrested by the matrix. SPECIMEN PREPARATION Specimens were prepared from 0.8 pct carbon steel piano wires of 0.015 in. initial diameter. The wires were given a thin nickel flash and a silver plate varying in thickness from 0.015 to 0.007 in., depending on the filament fraction desired. In order

Jan 1, 1965

By Robert W. Hunt

THE first pump of this character, made by H. R. Worthington, and, so far as the writer is informed, the first and only one of this kind ever constructed, is now in daily use in the above-named works. The water-pressure necessary for the working of the hydraulic machinery of this plant had been supplied, up to the time of the building of this pump, by two Worthington Duplex High Pressure Pumps, having steam-cylinders of 20 inches diameter and 12-inch stroke, with water-plungers of 72 inches diameter; eight inlet and eight outlet valves of 22 inches diameter, and pumping into a 6-inch pipe. These pumps required a large amount of steam, and, in consequence of the various additions to their duty, their capacity became far short of the work required. In preference to putting in another engine of the same class, it was decided to accept Mr. Worthington's proposition to build the compound one under description, he guaranteeing that it should be equal to the demands of the works, and at the same time cause a saving of from 5 to 6 tons of coal per day from the amount required to run the two old pumps. The new engine has been in operation about one month, and so far has exceeded the most sanguine expectations. It consists of two high-pressure cylinders of 21 inches and two low-pressure ones of 36g inches diameter, by 36-inch stroke, with water-plungers of 91 inches diameter. There are two air-pumps of 20 inches diameter by 18-inch stroke; the condenser being 24 inches diameter by 60 inches high. Both cylinders are jacketed with wood and felt, and the low-pressure cylinder also with live steam. The high and low pressure steam-cylinders are in line and immediately adjoining each other, while the inconveniences attending an internal stuffing-box are avoided by having two piston-rods for each of the low-pressure cylinders, running through stuffing-boxes on the outside of the smaller high-pressure ones. The steam-valves are very ingeniously designed balanced

Jan 1, 1876

By George Simkovich

It was hypothesized that solid-state point defects should alter the flotation properties of solids. Tests conducted on pure AgCl and AgCl doped with CdC12 show that atomic point defects exhibit an important role in the floatability of AgC1. Tests conducted on PbS doped with Ag2s or Bi2S3, also show that the defect structures resulting from these dope additions, i.e., a combination of electronic and atomic point defects, contribute significantly to the flotation of PbS. IT has been established that flotation occurs only when a finite contact angle exists between a solid and a gaseous bubble.' This angle, measured through the liquid phase, is expressed by the equation where the are inter facial free energies and the subscripts S, G, and L represent solid, gas, and liquid phases, respectively. As is seen in Eq. [I] three interface free energies, sG, sl, and GL, enter into the contact angle equation. Therefore, any variation in these energies which sufficiently varies the contact angle will, in turn, vary flotation processes. Changes made in any of the phases concerned, i.e., gas, liquid, or solid phase, are reflected through the changes occurring in two of the surface energy terms. Thus, a change in the liquid composition would be noted in sL and GL, and it is this phase, the liquid, which is most frequently altered in flotation studies., Changes in the solid phase must be reflected through the changes occurring in the sG and sL terms. In particular, it is hypothesized that changes in the surface concentrations of point defects in the solid-phase will alter the sG and sL terms which, in turn, will be reflected by flotation results. As an illustration of this hypothesis one may consider the defect structure and the flotation of AgC1. The bulk defect structure of AgCl is essentially one involving equal number of cation vacancies and interstitial cations.3 Upon adding CdC1, to AgC1, a greater number of silver ion vacancies are created in the bulk of the crystal.4 On the surface of the crystal the smaller binding forces and the free space accomodations may also allow for the creation of "surface interstitial anions", which will be designated as ad-anions. Thus, the point defect structure of the surface of AgCl doped with CdCl, will consist of cation vacancies and/or adanions. If the molecular forces responsible for the surface energies, ?SG and ?sL, are significantly altered by the presence of these surface point defects, then differences in flotation results will be noted as the concentration of these defects is varied. The defects present in AgCl are predominantly atomic in nature. In the case of PbS both electronic and atomic defects are present.5 This compound conducts electrically by either electrons or electron holes depending upon whether excess lead or excess sulfur is present. Upon disolving BiS3 in stoichio-metric PbS, one increases the concentration of cation vacancies and the number of electron carriers in the bulk of the crystal.5" At the surface, the possibility of ad-anions must also be considered. Conversely, upon dissolving AgS in stoichiometric PbS one increases the concentration of interstitial cations and the number of electronhole carriers in the bulk of the crystal.5,6' At the surface the interstitial cations will be designated as ad-cations. Thus, the point defect structure of the surface of a PbS crystal doped with Bi2S3 will consist of a number of cation vacancies and/or ad-anions and an excess of electrons. Conversely the point defects on the surface of a PbS crystal doped with Ag2S will consist of a number of ad-cations and an excess of electron holes. Again, as in the case of AgC1, should the molecular forces responsible for the magnitude of the interface free energies, ?sG and ?sL, be significantly altered by the presence of these surface defects then significant differences in flotation results will be noted as the concentration of these defects is varied. EXPERIMENTAL To test this hypothesis flotation tests were conducted on pure and doped AgCl and on PbS doped with either Bi2S3 or Ag2S. Preparation of the AgCl samples was performed as follows: AgCl and weighed amounts of CdC1, were melted in a porcelain crucible. The melt was then forced through a capillary tube and the particles emitted solidified in air as they fell about 1.5 meters. Spherical particles, -0.50 + 0.25 mm, were separated from the remaining solidified material

Jan 1, 1963

By P. R. Sperry, P. A. Beck, J. Towers

Dahl and Pawlek1 found that electrolytic copper develops extremely coarse grains at 1000°C after about 90 pct reduction by rolling. This coarsening occurs only under conditions of penultimate grain size, deformation, and alloying which lead to the "cube" recrystallization texture.l,2,3,5 The peculiar angular shapes and straight grain boundaries of the coarse grains were noted by several investigator.1,4,5 On the other hand, coarsening in Fe-containing aluminum or in AI-Mn alloys8 does not depend on a "cube" (or any well developed) recrystallization texture. It is true that increasing deformation by rolling, and, therefore, an increasingly well developed re-crystallization texture, are associated with decreasing incubation periods of coarsening.6-7-8 Nevertheless, coarsening readily develops in aluminum even after only 30 pct reduction by rolling, where the recrystallization texture is very weak.6,8 Also, coarsening was observed by Jeffries9 many years ago in sintered thoriated tungsten, which presumably has no preferred orientation. In all these cases coarsening is associated with grain growth inhibition by a dispersed second phase.8,9 The annealing temperature has to be suficiently high to overcome the inhibition at a few locations. But if it is too high, growth starts at many points, and the resulting grain size becomes much smaller.9 Normally, the coarse grains are more or less equiaxed, and the boundaries have a typical ragged appearance.6.8 Cook and Macquarie4 demonstrated that, in addition to the texture-dependent coarsening previously found at 1000°C,l electrolytic tough pitch copper may also coarsen at 800°C after 50 pct reduction by cross rolling. The coarse grains formed under such conditions have rounded shapes and ragged boundaries, like those in aluminum. When the annealing temperature is higher, the tendency for their formation decreases. All these observations suggest that the coarsening at 800°C is associated with inhibition by a second phase. Actually, coarsening at 800°C after 50 pct reduction by cross rolling was observed only in tough pitch copper,4 which contains Cu2O particles. On the other hand, the texture-dependent 1000°C coarsening occurs in both tough pitch and oxygen-free copper;4 it does not appear to depend on the presence of a dispersed second phase. However, the interpretation of the 800°C coarsening in Cu after 50 pct rolling as an inhibition-dependent process, similar to the coarsening in A1-Mn alloys, is somewhat weakened by the fact that this coarsening was reported4 to occur only after cross rolling, and not after straight rolling. It was, therefore, decided to re-examine this question. A 1 in. diam electrolytic tough pitch copper rod, No. 2 hard drawn, was annealed for 20 min at 700°C, rolled to 0.5 in., annealed 10 min at 700°C, and straight rolled to 0.064 in. It was then given a penultimate anneal of 20 min at 500°C and it was cut into four sections, which were given final reductions by straight rolling as follows: A 30 pct reduction of area B 50 pct reduction of area C 70 pct reduction of area D 90 pct reduction of area Specimens cut from the four sections were finally annealed at 800°C in an oxidizing atmosphere. Strip A remained fine grained up to 10 hr, but the specimen annealed 12 hr consisted of only 2 large grains. Strip B had a few scattered large (1/2 to 3/4 mm) grains after 1 min, although the balance of the specimen consisted of fine grains of about 0.02 mm. After 5 min there were several 10 to 15 mm grains present, and after 1 hr strip B was completely coarsened. The coarse grains had the same characteristics (see Fig 1) as those obtained by Cook and Macquarie at 800°C after cross rolling. Strip C had several grains of 0.05 to 1 mm after 1 min, but it was still largely fine grained after 12 hr. After 48 hr it consisted entirely of grains of about 0.5 to 4 mm, with an extraordinarily large number of twin bands. Strip D remained com- pletely fine grained after 4 hr at 800°C. These results indicate that, in the deformation range of 30 to 70 pct reduction, the incubation period for coarsening as well as the rate of growth and the final size of the coarse grains decreases with increasing deformation. Similar

Jan 1, 1950

By J. A. Hren, G. Thomas

A high-temperature stage has been used to study precipitation and dissolution in thin foils of Al-20pct Ag alloy directly in the electron microscope. The results show that the aging characteristics are similar to those observed for bulk materials, and in addition, direct evidence is presented for clustering at the solid solution temperature. The limit of solubility of G. P. zones is-350°C. The heterogeneous precipitation, the growth and dissolution of ?&apos;have been studied in detail. Growth of ?&apos; parallel to the basal planes, occurs by continuous motion of inter -facial partial dislocations. Growth stops at intersecting particles due to formation of sessile a/6 <110> interfacial dislocations. Growth normal to the habit plane occurs by the spontaneous nucleation of partial dislocations on alternate (111) planes and the thickening rate is --10-3= times the lengthening rate. The precipitates dissolve in layers and the final product is a whole a/2 <110> dislocation . The nucleation -growth -dissolution processes are thus completely reversible. Kinetic data obtained from the dissolution rates of ?&apos;particles enable the diffusion coefficient to be determined and the activation energy is found to be 37.5(±4) kcal mol-1, which is that expected for dzffusion of silver in aluminum. The velocity of the interfacial dislocations is thus dependent solely on the rate of diffusion of silver atoms. RECENTLY it was demonstrated that a high-temperature stage could be effectively used in the electron microscope to follow directly the processes of precipitation and dissolution in thin foils of A1-4 pct Cu alloy.&apos; These experiments also provided kinetic data which enabled the diffusion coefficient to be estimated. This new development of electron metallography opens up many fruitful areas of research and it was decided to investigate the aging behavior in thin foils of A1-20 pct Ag alloy, particularly the mechanism of heterogeneous precipitation (i.e., precipitation on lattice defects). This system was chosen because the aging characteristics of bulk specimens are now well known,2"7 and because we wished to obtain more details of the role played by partial dislocations and stacking faults in the nucleation growth and dissolution of the hcp ?&apos; phase. This is of interest for the general case of fcc-- hcp transformations. Part of the A1-Ag phase diagram is shown in Fig. 1. The use of a high-temperature stage also enables a study to be made of the clustering process (formation of G. P. zones) and to determine the structure of the solid solution prior to the usual quenching and aging procedures. It is also possible to obtain kinetic data from measurements of the rates of dissolution of precipitate particles. Unlike the results of previous experiments on A1-4 pct CU 1 where much of the initial precipitation occurred on the foil surfaces, the results on the A1-20 pct A1 alloy were identical to those reported for bulk specimens6,7 and no surface precipitation was ever observed. Thus, it was possible to follow the aging sequence: G.P. zones — ?&apos; — ? directly in the thin foils. This paper is concerned with the formation and dissolution of zones and the ?&apos; phase, and no attempt has been made so far to follow the mode of discontinuous precipitation of ?. I) EXPERIMENTAL DETAILS The high-purity A1-20 pct Ag alloy was prepared by the Aluminum Co. of America in the form of 0.001-in.-thick sheets. These were cold rolled with intermediate anneals to a thickness of 0.0004 in.,

Jan 1, 1963

By Thomas A. Steven

Most mineralized areas in the central San Juan Mountains, Colorado, are associated with the youngest subsidence structures in a large volcanic cauldron complex that formed concurrently with eruption of the surrounding ash-flow field. Two local types have been recognized: (1) fissure-vein deposits along faults characterized by relatively late movement, and (2) hydrothermally altered and mineralized areas associated with postsubsidence Fisher Quartz Latite centers. The first type has provided most production in the past; the potential of the second type has yet to be adequately tested.

Jan 1, 1968