Search Documents

By F. W. Rols-Hausen, F. W. Jessen

It is the purpose of this paper to present data on brines occurring in the Frio formation of the Texas Gulf Coast, and to show how their composition varies, (1) with depth below the surface, (2) with depth below the top of the formation, and (3) along the approximate strike. The brines vary in chloride content from 3,180 to 73,000 p.p.m., though the average salinity of the salt waters is shown to vary with total depth; the concentration being 35,000 to 40,000 p.p.m. at 3500 to 5500 ft., slightly less than 50,000 p.p.m. chloride at 5500 to 6500 ft. and average 38,000 to 40,000 below 6500 feet. From the analyses available, it appears that the highest concentration of salts occurs in the upper 300 ft. of the formation, while lower salinity is found with increasing depth below this point. The salt waters from wells in Starr County show less concentration of dissolved salts than in any other group of wells farther north along the strike. In all, 116 analyses from 63 fields and 14 wildcats, from depths ranging from 1300 to 11,400 ft. below the surface and from z to 3240 ft. below the top of the Frio, are recorded. Introduction Brines have been studied for many Years in an attempt to solve some of the geologic and production problems associated with the production of oil and gas. One practical application of study of . water analyses is the correlation of waters occurring above, in, or below the producing sand in the same field or throughout the same formation. The Frio formation, the series of sands and shales occurring below the Marginulina zone and above the Vicksburg, is one of the major oil and gas-producing formations in the Texas Gulf Coast. Fossils are rare or absent in the upper Frio throughout most of the area. When available, cuttings and cores, and electric logs were used to determine the top of the Frio. A change in lithology was used to determine this point in most of the wells, and fossils were used in some of the deep wells. It is realized that a change in lithology is not perfect for correlation purposes over long distances and some of the trends may be influenced by the inability to differentiate between the nonfossiliferous Marginulina zone and the Frio. It underlies virtually all the area shown on the accompanying map (Fig. I). Although it is not productive in the updip facies, it has been explored to a limited degree below I2,000 ft. Further more, toward the coast line future drilling to deeper depths should encounter this formation. Although thousands of wells have penetrated or drilled entirely through the formation, very few water samples have been secured from the many sands occurring in this formation and analyzed. Previous Investigation No previous published study has been made of the chemical composition and concentration of waters from the Frio formation. However, one water analysis

Jan 1, 1944

By F. W. Jessen, F. W. Rols-Hausen

It is the purpose of this paper to present data on brines occurring in the Frio formation of the Texas Gulf Coast, and to show how their composition varies, (1) with depth below the surface, (2) with depth below the top of the formation, and (3) along the approximate strike. The brines vary in chloride content from 3,180 to 73,000 p.p.m., though the average salinity of the salt waters is shown to vary with total depth; the concentration being 35,000 to 40,000 p.p.m. at 3500 to 5500 ft., slightly less than 50,000 p.p.m. chloride at 5500 to 6500 ft. and average 38,000 to 40,000 below 6500 feet. From the analyses available, it appears that the highest concentration of salts occurs in the upper 300 ft. of the formation, while lower salinity is found with increasing depth below this point. The salt waters from wells in Starr County show less concentration of dissolved salts than in any other group of wells farther north along the strike. In all, 116 analyses from 63 fields and 14 wildcats, from depths ranging from 1300 to 11,400 ft. below the surface and from z to 3240 ft. below the top of the Frio, are recorded. Introduction Brines have been studied for many Years in an attempt to solve some of the geologic and production problems associated with the production of oil and gas. One practical application of study of . water analyses is the correlation of waters occurring above, in, or below the producing sand in the same field or throughout the same formation. The Frio formation, the series of sands and shales occurring below the Marginulina zone and above the Vicksburg, is one of the major oil and gas-producing formations in the Texas Gulf Coast. Fossils are rare or absent in the upper Frio throughout most of the area. When available, cuttings and cores, and electric logs were used to determine the top of the Frio. A change in lithology was used to determine this point in most of the wells, and fossils were used in some of the deep wells. It is realized that a change in lithology is not perfect for correlation purposes over long distances and some of the trends may be influenced by the inability to differentiate between the nonfossiliferous Marginulina zone and the Frio. It underlies virtually all the area shown on the accompanying map (Fig. I). Although it is not productive in the updip facies, it has been explored to a limited degree below I2,000 ft. Further more, toward the coast line future drilling to deeper depths should encounter this formation. Although thousands of wells have penetrated or drilled entirely through the formation, very few water samples have been secured from the many sands occurring in this formation and analyzed. Previous Investigation No previous published study has been made of the chemical composition and concentration of waters from the Frio formation. However, one water analysis

Jan 1, 1944

By Hugh D. Pallister, Richard W. Smith

The Alabama flake-graphite industry has flourished only in times of war when importations of foreign graphite for crucible use have been greatly curtailed or cut off. World War I was a boom period and in 1918 some 30 plants produced 7,795,475 Ib. of flake graphite. The industry languished following the war and no graphite was produced from 1929 to 1939. The Federal Bureau of Mines began investigating the Alabama graphite deposits in 1940 and worked out modern recovery methods that were applied to production during part of World War 11. A prospecting program disclosed reserves of over 25 million tons of graphtic schists. In 1942 the War Production Board authorized the enlargement of the only plant then producing flake graphite and the construction of two new plants. Production of flake graphite from these three plants in 1943 is estimated at 8,100,000 lb. Increased imports from Madagascar late in 1943 shut down one of the new plants and curtailed production at the other. Alabama flake graphite has not yet been able to compete with Madagascar graphite for use in the manufacture of any but small graphite crucibles. The future of the industry must depend on meeting the higher carbon content demanded for other uses. Introduction The flake-graphite deposits of Alabama are confined to a narrow belt extending for about 60 miles southwest from the northeast corner of Clay County across Coosa County to the edge of the Coastal Plain in Chilton County (Fig. I). The continuity of the beds is broken by a 10-mile gap between Millerville in Clay County and Goodwater in Coosa County. The Clay County beds extend about 27 miles northwest of this gap, with a width of 3 to 4 miles near Millerville and of less than a mile at the northeast end. The Coosa-Chilton are? is about 33 miles long with a fairly consistent width of 2 to 3 miles. Geologically the graphite belt lies near the northeast boundary of the outcrop of metamorphic rocks of the Ashland series, a complex group of intensely folded and faulted beds of pre-Cambrian age composed mostly of quartz-mica schist, in which the mica is predominantly muscovite; garnet-mica schist, in which biotite is more common; and hornblende schist. Flake graphite is found in commercial quantities only in the quartz-mica schist. The best graphite, both in quantity and quality, is found in schist cut by numerous small pegmatite stringers along the planes of the schistosity. The pegmatites themselves contain little graphite, but the adjacent country rock is normally rich. . The schist was derived through the recrystallization of shale during the intrusion of the pegmatites, the graphite being derived from amorphous carbon in the shale. The intrusion of the pegmatites, and therefore the size and quantity .of the graphite flakes, seems to have a structural control.

Jan 1, 1948

By Hugh D. Pallister, Richard W. Smith

The Alabama flake-graphite industry has flourished only in times of war when importations of foreign graphite for crucible use have been greatly curtailed or cut off. World War I was a boom period and in 1918 some 30 plants produced 7,795,475 Ib. of flake graphite. The industry languished following the war and no graphite was produced from 1929 to 1939. The Federal Bureau of Mines began investigating the Alabama graphite deposits in 1940 and worked out modern recovery methods that were applied to production during part of World War 11. A prospecting program disclosed reserves of over 25 million tons of graphtic schists. In 1942 the War Production Board authorized the enlargement of the only plant then producing flake graphite and the construction of two new plants. Production of flake graphite from these three plants in 1943 is estimated at 8,100,000 lb. Increased imports from Madagascar late in 1943 shut down one of the new plants and curtailed production at the other. Alabama flake graphite has not yet been able to compete with Madagascar graphite for use in the manufacture of any but small graphite crucibles. The future of the industry must depend on meeting the higher carbon content demanded for other uses. Introduction The flake-graphite deposits of Alabama are confined to a narrow belt extending for about 60 miles southwest from the northeast corner of Clay County across Coosa County to the edge of the Coastal Plain in Chilton County (Fig. I). The continuity of the beds is broken by a 10-mile gap between Millerville in Clay County and Goodwater in Coosa County. The Clay County beds extend about 27 miles northwest of this gap, with a width of 3 to 4 miles near Millerville and of less than a mile at the northeast end. The Coosa-Chilton are? is about 33 miles long with a fairly consistent width of 2 to 3 miles. Geologically the graphite belt lies near the northeast boundary of the outcrop of metamorphic rocks of the Ashland series, a complex group of intensely folded and faulted beds of pre-Cambrian age composed mostly of quartz-mica schist, in which the mica is predominantly muscovite; garnet-mica schist, in which biotite is more common; and hornblende schist. Flake graphite is found in commercial quantities only in the quartz-mica schist. The best graphite, both in quantity and quality, is found in schist cut by numerous small pegmatite stringers along the planes of the schistosity. The pegmatites themselves contain little graphite, but the adjacent country rock is normally rich. . The schist was derived through the recrystallization of shale during the intrusion of the pegmatites, the graphite being derived from amorphous carbon in the shale. The intrusion of the pegmatites, and therefore the size and quantity .of the graphite flakes, seems to have a structural control.

Jan 1, 1948

By Philip R. Strand, O. F. Stewart

Vermiculite is the name generally applied to the group of hydrated ferromagnesian aluminum silicates that are characterized by the ability to expand when heated. This process, called exfoliation, results in a lightweight product of commercial value. Most uses of vermiculite are for the expanded material. The chief markets are in construction, agriculture, and horticulture, with lesser uses in general industry. Composition and Properties Vermiculite, in its natural state, has the characteristic micaceous habit, a perfect basal cleavage which causes splitting into thin laminae that are soft, pliable, and inelastic. The structure of vermiculite is basically that of a talc. The prominent monoclinic crystal faces are often marked by lines at 60° and 120°. Hardness varies from 1.5 to 2 or more; specific gravities are between 2.1 and 2.8; color varies from almost clear to amber, bronze, brown, green, or black. Vermiculite feels like talc, especially when wet. Although much research has been performed on the chemical and structural composition, there is not yet complete agreement on the exact formula. This is to be expected when different workers have examined the many different varieties. Vermiculite is not considered to be a single mineral species but a family of related minerals. The structural formula for a trioctahedral vermiculite may be written: (H20)-(Mg,Ca,K)-(A12,Fe,Mg)-(Si,A1,Fe)4O10 (OH) 2 Hydrobiotite also occurs with vermiculite and is usually considered a vermiculite for commercial uses. When heated quickly to elevated temperatures, vermiculite expands by exfoliating at right angles to the cleavage into wormlike particles. The name vermiculite is derived from the Latin vermiculare, to breed worms. This characteristic of expansion is the result of the mechanical separation of the layers by the rapid conversion of contained water to steam. The decrease in bulk density of commercial grades is usually approximately 10 times, from 50 to 5 lb/ft3, but varies depending on the quality, size, and furnace efficiency. Individual flakes may expand up to 30 times. Vermiculite may also be expanded by soaking in chemicals such as hydrogen peroxide, weak acids, and other electrolytes. Color change during expansion is dependent upon the type of vermiculite and furnace conditions. Heating in an oxidizing atmosphere produces a dull gray or tan color, whereas a reducing atmosphere can produce a bronze or gold color. The expansion of the vermiculite crystal results in large pores being formed between the platelets. Thus, exfoliation makes available a large increase in void volume which is important in the application of vermiculite as a chemical carrier. Mathieson and Walker (1954) state vermiculite must be regarded as a true clay mineral. The characteristic properties of the mineral, such as high cation exchange capacity, organic complexing ability, and variable interlamellar distance are very similar to those of montmorillonite. The cation exchange capacity of vermiculite is one of the highest of all the clay minerals. The interplatelet space is accessible to penetration by some electrostatically neutral molecules. Water and glycerine are two common substances whose molecules may be so imbibed. In the natural state and under normal atmospheric conditions, water occupies the spaces between the silicate layers. The crystal d-spacing is near 14.2A. By differential thermal analysis, it has been determined that the water

Jan 1, 1983

By Boyd Dudley

THE material presented in this paper is an abstract of a thesis submitted by the writer to the faculty of the Massachusetts Institute of Technology, as part requirement for the degree of Master of Science. The investigation was undertaken at the suggestion of Prof. H. 0. Hofman, and it was conducted, under his direction, in the laboratories of the Mining Department of the Institute. The purpose of the work was, first, to study some of the reactions that have been considered as a part of the mechanism of the chloridizing roast, and second, to study the conditions under which nickel oxide and copper oxide may be chloridized. While the production of chlorine gas by various reactions during the chloridizing roast may not be primarily useful in the chloridation of metal oxides and compounds, it nevertheless serves a useful purpose in preventing the dissociation and decomposition of chlorides once they have been formed; for example, the dissociation of cupric chloride into cuprous chloride and chlorine. Therefore it was thought that a study of some chlorine-producing reactions would prove of interest, and the first series of experiments dealt with this phase of the subject. The object of the latter part of the work was to show the possibility of treating heavy sulphide ores, such as those of Sudbury, Ontario, containing much iron and small amounts of copper and nickel, by chloridizing and removing the copper, leaving an iron-nickel oxide product suitable for smelting in the blast furnace for nickel-bearing pig iron. The chloridizing of the copper would, of course, be preceded by a roast for the removal of sulphur, the sulphur oxides being available for the manufacture of sulphuric acid, if under the local conditions this product would be of commercial value.

Jan 12, 1914

By Edward Saibel, W. T. Lankford

DURING the course of an investigation of the plastic flow of aluminum aircraft sheet under combined loads, several problems arose in which analyses of the conditions leading to unstable plastic flow were needed. In order to provide these analyses, and in the hope of attaining a better understanding of the general problem of unstable plastic flow, the present study was undertaken. It is well known that unstable plastic flow is associated with a form of mechanical instability frequently observed during the plastic deformation of ductile metals. This instability is characterized by the fact that, at its onset, plastic straining will proceed at a constant magnitude of the externally applied forces. It is further typical that the resulting unstable flow is generally accompanied by the formation of a neck, a local bulging, or some other form of heterogeneous deformation. Perhaps the most familiar example of unstable plastic flow to the metallurgist is the formation of the neck in the ordinary tension test. It is well known that in this test most metals exhibit a maximum in the externally applied load, followed by the process commonly referred to. as "necking down." Instability in the simple tension test has been frequently discussed and numerous investigators 1,2.3,12 have derived the criterion for instability in terms of a critical rate of strain hardening. It is the purpose of the present study to extend the criterion for unstable flow to the more general case where the body undergoing flow is subjected to combined loads. It is hoped that the problems considered will provide a more consistent picture of the general features of this important form of mechanical instability. The most practical implications of instability in plastic flow arise in connection with sheet metal forming operations. In the formation of a great many sheet metal parts, the deformations are produced primarily by stretching. If the conditions which lead to unstable flow are fulfilled in such a formation, and if the resultant instability leads to a pronounced localization of flow, then the useful limit of ductility of the material will have been reached. It is also essential that the effects of instability be taken into consideration in any study of the plastic flow and rupture of metals under combined stresses. In general, when unstable plastic flow is initiated, straining becomes localized, the geometry of the test specimen changes, and the state of stress in that portion of the specimen undergoing plastic flow is no longer under external control. In many past studies of the effects of combined stresses on flow and rupture, account has not been taken of the fact that, although a given test may be started under constant

Jan 1, 1947

By George Tryon, E. A. Barnard

The importance of the conservation of the waste heat contained in copper reverberatory furnace gases was realized very early by those in charge of operation at Anaconda. The first attempt to utilize it was in preheating the air used for combustion of the coal. This was done by forcing the air through ducts surrounding the flue-gas downtake and continued down beneath the furnace hearth to the firebox. Any small advantage gained by the heat transferred from the flue gases was more than offset by the losses sustained in cooling the hearth, therefore this process, after several trials, was soon discarded. It was first used at the Old Works as early as 1893 and again for a comparatively short time on the original furnaces at the Washoe smelter, or present works. Water-tube boilers came into general use very rapidly after 1890. Their adaptability for waste-heat steam generation, as well as the saving to be effected by the production of cheap steam from this source, was soon recognized. The first waste-heat boiler to be used in connection with a matte furnace at Anaconda was installed in September, 1900, at the "Old Lower Works." It consisted of a 100-hp. "Cook," vertical water-tube boiler. This boiler had 65 small perpendicular tubes arranged in concentric circles around a 10-in. tube in the center. These tubes were expanded into 4 ft. 4 in. inside diameter cylindrical steel top and bottom drums which served as the steam and mud drums respectively. This boiler was set in a cylindrical brick housing into which the furnace gases entered just above the mud drum and thence circulated upward around the tubes and steam drum to the stack. This installation proved unsatisfactory, presumably on account of difficulty with dust, and was soon abandoned. However, the possibilities for steam generation were undoubtedly encouraging for shortly afterwards (December, 1900) a 300-hp. Stirling boiler was installed, to be followed by two more in the spring of 1901. The choice of the Stirling type of boiler for application to copper reverberatory furnaces was particularly fortunate, as the arrangement of the tubes appears to combine to a great extent the maximum contact of the gases with the heating surfaces of the boiler and at the same time

Jan 1, 1934

By W. L. Zeigler

THE year 1930 in the Ceur d? Alene district was one of curtailment in production. Many of the small properties were closed entirely and only three large. producers, the Bunker Hill & Sullivan, Hecla, and the Morning mines were left producing at capacity. No innovations in milling were evident, but progress was made in reducing costs as is always necessary in times of low metal prices. One new concentrator was constructed, a 500-ton daily capacity selective flotation plant for, the Jack Waite Mining Co. This mill uses coarse crushing, followed by hand sorting, for both a high-grade ship- ping ore and waste. The remainder of the ore leaving the sorting belt is crushed in a new type Traylor reduction crusher to %-in. size and stored in large capacity mill ore-bins. The grinding is done with ball mills, in closed circuit with a Dorr classifier to 75 per cent - 200 mesh. Minerals Separation 24-in. flotation machines are used both for a lead and a zinc concentrate, with double cleaning in each case. The concentrates are dewatered in Dorr thickeners and filtered on Oliver late-type filters.

Jan 1, 1931

By A. G. H. Andersen, A. W. Kingsbury

SILICON bronzes containing iron are used to a considerable extent in industry, under the trade name of P.M.G. alloys. Various classes of wrought alloys fall in the composition range 1.5 to 3.5 per cent silicon, and 0.5 to 2.5 per cent iron. Castings may contain as much as 6 per cent silicon and 3 per cent iron at present. The constitutional diagrams of these alloys are thus of considerable practical importance. Copper-silicon-binary alloys have been thoroughly investigated by a number of workers, the latest reports being those of C. S. Smith1 and of A. G. H. Andersen.2 Although much work has been done on iron-copper alloys,3 recorded investigations on the copper-rich copper-iron binary constitutional diagram are not numerous. Tammann and Oelsen4 determined the solubility limits of iron in copper by means of magnetic measurements, and found that the solubility of iron in copper amounts to a fraction of one per cent at 400°C., increasing slowly to one per cent at 800°C. From 800°C., the solubility increases rapidly and attains 4 per cent at 1100°C. Hanson and Ford,5 using electrical resistivity measurements and the microscope, determined a somewhat different solubility limit. Of earlier X-ray works on the copper-iron system, very little has been published. The work by Bradley and Goldschmidt6 on copper-iron-aluminum alloys includes some information on the copper-iron binary. These investigators conclude that substitution of iron in the copper lattice decreases the spacings, which is contrary to the evidence of the present work. Hanson and West7 have investigated the ternary alloys of copper with iron and silicon. Although their diagrams are valuable contributions to the understanding of these alloys, they did not recognize the kappa phase,12, 7,8 and their diagrams do not everywhere conform to the phase rule. The present work contains a check by means of X-rays of the solid solubility limit of iron in copper, and an X-ray investigation of the ternary-phase diagram, which, owing to present conditions, it became necessary to curtail considerably. PREPARATION OF SAMPLES Castings weighing about 75 grams were melted under vacuum. The charges were made up of ingot iron, copper cathodes from Laurel Hill, and refined silicon supplied by the Electrometallurgical Co. Alundum crucibles were generally used. The exceptions were alloys 77 and 78, which were melted in graphite crucibles. The ingots were annealed at 800°C. for one week, then samples were cut for chemical analysis. Longitudinal sections of the binary alloy ingots were hammered into plates 3 in. thick. Wherever possible, these plates were homogenized at temperatures ensuring

Jan 1, 1942

By E. E. Bach

STATEMENT OF THE PROBLEM THE administration of industrial organization today embraces more than the cost of production and selling prices. Competition is deeper seated than mechanical devices, overhead charges, and a shrewd manipulation of the markets. Despite the "down-to-the-minute" equipment and the "last word in organization," it is quite evident that "capacity production" will be an unknown quantity until the workman is considered as a producer, in relation to his home, as he is now considered in relation to industry. Whether or not a man shall do an honest day's work is as much a psychological condition as it is a matter of physical strength or skill. His attitude toward his work each morning is determined, to a large degree, by the environment of his home. Whether this attitude, good or bad, obtains the day through will depend entirely upon the one fact as to whether the corporation which employs him does or does not differentiate between the mechanical factor and the human factor in industry. To be more specific, sociological work, under whatever name, should be of such a character as to influence the life of a workman in such a manner as to establish a cooperative interest in his work, foster within him a spirit of contentment in his home, lead him-so to employ his leisure time that he will not lower his efficiency as a workman, destroy his domestic happiness, or endanger his standing in the community as a citizen. While no fixed rules of procedure can well be formulated for the development of the work, yet definite lines of activities will readily present themselves as applicable to the individual needs of a community. This is especially true where community influences and agencies pertaining to general welfare are easily correlated.

Jan 2, 1918

By AIME

Generally speaking, the mining industry had a good year in 1948 with most mineral products being produced in record quantities for peacetime standards. The big boys-iron and steel, coal, and petroleum-indicated the industry-wide trend by surpassing 1947 production figures. Although exploration and expansion are being pushed aggressively in all branches of the industry, there is a pronounced trend to engineering and research directed at cutting production costs, improving the product, and finding new markets. These improvement campaigns are making headway; in the bituminous coal industry, 5.43 tons per man employed is the new production record; 83 million tons of iron ore were unloaded at lower Lake ports, breaking another peacetime record; magnesium, due to improvement in manufacturing techniques, now competes on the market with aluminum.

Jan 1, 1949

By M. R. Geer, Franklin T. Davis, H. F. Yancey

COKE with low phosphorus content is required by some of the electrometallurgical and chemical plants recently attracted to the Pacific Northwest by the hydroelectric power available from Bonneville and Grand Coulee dams. Shipping such coke into the area from eastern points involves a high freight charge, and during wartime consumes precious rail and ship-bottom space, so it is highly desirable to produce coke from the coking coals of Washington to meet the requirements of these industries. Although coke has been made from Washington coals since 1884, little has been known about their phosphorus contents or about the extent to which phosphorus could be reduced by cleaning. An investigation was undertaken, therefore, to determine the manner in which phosphorus occurs in the coking coals of Washington and its amenability to removal by ordinary coal-washing methods. PREVIOUS WORK Phosphorus is a deleterious element in coke used for numerous metallurgical processes, including the production of pig iron, yet comparatively little published information is available on the occurrence and elimination of phosphorus in any of the coals of this country. A variation from 0.009 to 0.062 per cent phosphorus in various horizons of the Pittsburgh bed in the Connellsville region of Pennsylania has been reported,1 and a reduction in phosphorus content from 0.020 per cent in the raw coal to 0.018 per cent in the washed coal was obtained in washing coal from the same bed in the Pittsburgh area;2 the latter figures represent average analyses for a year's operation of the washery on about 800,000 tons of coal. A reduction in phosphorus content from 0.018 to 0.011 per cent in washing coal from the Pittsburgh bed at another washery was observed, and the same report provides data on the phosphorus reduction obtained by separating 10 other coals on a bath of 1.35 specific gravity.3 European investigators have been especially active in correlating phosphorus content with petrographic analysis; fusain and durain generally contain the highest percentage of phosphorus, but this relationship is not universal.4 Some of these investigators have found that phosphorus is removed in the coal-washing process,5 but others have observed that the clean coal contained as much or even more phosphorus than the raw coal.6

Jan 1, 1944

By Edmund J. Pryor

DURING the war years restrictions on travel, pressure of work, and the irregular arrival of technical literature from abroad combined to severely isolate Great Britain in a period of intense war expansion of the art and practice of mineral dressing. Many British technicians were fully occupied with the day-to-day problems of improvising substitutes as regular sources of supply failed. and with mastering the strange demands and working conditions of wartime. After a long day spent between ones laboratory and production work, the rest of the waking hours were often filled with fire watching or home guard patrol activities, substituting for a night-shift manager, or "resting" in a dugout while the bombs came down. There was no time for serious study of such technical literature as survived the Atlantic crossing.

Jan 1, 1947

By Roy T. Southin*

The finding of Wojciechowski and Chalmers that columnar crystal growth can be stopped by an already existing network of equiaxed crystals is supported by other recently reported work on both static and mechanically stirred ingots.27,28 Support for the dendrite arm fragmentation mechanism, too, can be obtained by comparing the effects of spinning on ingots cast in a material which has a dendritic solid/liquid interface during solidification with one which has a cellular interface, since no evidence of change at the interface, other than a change in growth direction, can be found in the cellular material. But there are alternative ways of producing an equiaxed zone in materials which characteristically solidify with a cellular interface. For example, interrupted spinning of a normally cast ingot can do it. In this case it has been shown28 that the equiaxed zone is caused by the showing of dendritic particles from the top surface of the ingot to nucleate a network of equiaxed crystals which forms a barrier to the continued growth of the columnar grains. This showering has also been shown to be a major effect in materials solidifying with dendritic interfaces. It has also been proposed28,29 that, for an equiaxed zone to form, not only must nuclei be present ahead of the interface but also these nuclei must grow to sufficient size to be a barrier to the further growth of the columnar grains. A further requirement is that a network of these grains continually be produced ahead of the growing interface; otherwise there is a reversion to columnar growth as found by Wojciechowski and Chalmers. In normally cast ingots it is possible for nuclei ahead of the interface to grow since during a large portion of the solidification time there is no temperature gradient ahead of the interface,30 and, in fact, the liquid may be slightly undercooled.29 This then is the major difference between the work under discussion and normal industrial solidification conditions, since Wojciechowski and Chalmers imposed a considerable temperature gradient in the liquid. The statement in the Wojcieshowski and Chalmers paper that one needs to lower the temperature gradient

Jan 1, 1969

By Chester Wells Purington

Situation.—The Camp Bird mine is in Imogene basin† (Fig. 1) at the head-waters of Canon creek, a branch of the Gunnison, in the southern part of Ouray county, Colorado, towards the northern edge of the region known as the San Juan mountains, and about 10 miles W. of the continental divide. It is 8 miles by wagon-road from Ouray, the terminus of a branch of the Rio Grande' Southern railway. The distance from Denver to Ouray is 387 miles by rail. In an air-line, the mine is 190 miles SW. of Denver. The altitude of the town, tunnel and buildings is 11,200 ft., and level No. 2 is 11,500 ft., and No. 1 is 11,670 ft., above sea-level. The lowest point of the lode-ontcrop, which crosses the basin E. and W., has an elevation of 11,850 ft., and that of the highest point, on the divide between Imogene and Tomboy basins, is 13,250 ft. On the eastern slope of the Imogene basin (towards Ironton) the vein is less clearly defined on the surface. Ownership and Extent.—At the time of the writing of this paper, the property is owned by Mr. Thomas I?. Walsh, and operated under the management of Mr. J. W. Benson. It

Jan 1, 1903

By E. T. Turkdogan, Klaus Schwerdtfeger

OelSEN and Maetz1 detected some 20 years ago the existence of a miscibility gap in iron oxide-CaO-P2O5 slags melted in iron crucibles at about 1400°C. Because of the importance of this system for the dephos-phorization of steel in the basic Bessemer process, equilibria between liquid iron and selected iron oxide-CaO-P2Q slags have been measured since by numerous investigators.2-5 When in equilibrium with metallic iron, the iron oxide of the slag is present mainly as FeO. In connection with oxygen-blowing steelmaking processes, it is useful to know the phase relations in the slag system at higher oxygen pressure, when major parts of the iron oxide are present as Fe2O3. This problem was investigated by Turkdogan and Bills7 by equilibrating the oxide mixtures contained in platinum crucibles with CO2-CO mixtures at 1550°C. It was found that increasing the Fe2O3 content decreases the composition range of the miscibility gap strongly so that the miscibility gap has almost disappeared at pco2/pco = 75. This result was refuted by the careful work of Olette et a1.,''' who equilibrated their slags with controlled Ha-H2-Ar gas mixtures. Their equilibrium measurements, at 1600°C and at oxygen pressures of 5 x 10"* and 10"5 atm, showed that the oxidation state of the iron has almost no influence on the formation of the miscibility gap. The present experiments were undertaken to check the previous results of Turkdogan and Bills. The experiments were performed at 1625°C in the strongly oxidizing atmosphere of air (PO2 = 0.20 atm) for which no experimental data are available. About 10 g of slag were melted in platinum crucibles and held at constant temperature for 1 hr. After equilibration, the crucible was rapidly pulled out of the furnace and cooled in air. The platinum crucible was removed from the sample. The two slag layers were carefully separated with a small diamond disc, and the surface of the top layer, which may have changed its oxidation state during cooling, was removed. The slags were crushed and analyzed chemically for CaO, P2O5, Fe2+, and Fetotal. The starting mixtures were prepared by sintering the desired amounts of reagent-grade 2CaO . P2O5 - H2O, CaCO3, and Fe2O3. Sintering and subsequent crushing were done three times to ensure homogenization. Molybdenum wire resistance heating was used. The furnace was provided with a recrystallized alumina reaction tube which was left open to air at the top. The temperature was controlled electronically. The reported temperature was measured with a Pt/Pt-10 pct Rh thermocouple and is estimated to be accurate within +5°C. The composition of the equilibrated melts is given in Table I. For the graphical illustration of these quaternary slags the type of projection suggested by Trömel and Fritze10 was used. In this representation, Fig. 1, the composition point of a mixture within the tetrahedron Fe2O3-CaO-P2O5-FeO is projected into the Fe2O3-CaO-P2O5, triangle (triangle I) so that the direction of projection is parallel to the side FeO-Fe2O3, and into the triangle Fe2O3-P2O,-Fe0 (triangle 11) so that the direction of projection is parallel to the side CaO-P2O5, of the tetrahedron. The projected point has the coordinates wt pct CaO, wt pct P205, and wt pct (FeO + Fe2O3) in triangle I and wt pct FeO, wt pct Fe2O3, and wt pct (CaO + PzO5) in triangle 11. Both triangles are turned into the same plane around the Fe203-P20, side of the tetrahedron. An illustration of the projection of a quaternary point in the present system is shown in Fig. 1. The advantage of this type of projection is that all four components for an equilibrium curve can be read directly from the diagram. The present results are shown graphically in Fig. 2. The curves depicting the miscibility gap are dashed in parts where no experimental points were obtained. The composition range covered by the miscibility gap

Jan 1, 1968

By J. Stringer, I. W. Edington, C. R. Rarey

THE geometrical interpretation of transmission electron micrographs of hcp metals is more complicated than the equivalent interpretation of cubic metal for two reasons: firstly, prominent zone axes are not in general normal to prominent planes, so that a simple diffraction pattern often corresponds to a nonra-tional foil plane; and secondly, the Miller-Bravais sys-tem of indexing directions is not easy to visualize. In this, the indexing is referred to the Bravais four-axis system, and the direction is labeled [hkil], chosen so that and I are shown in Fig. 1. Some geometrical relationships useful for the interpretation of transmission micrographs have been calculated and are tabulated below: 6) Direction of the intersection of two planes; this is easily calculated by applying Condition 4 to both planes: a direction that lies in both planes is clearly their direction of intersection. Some of the above expressions have also recently been given by Otte and Crocker;' Expression 5 is of course in most standard crystallographic texts. It is generally considered easier and quicker to use graphical methods for the interpretation of electron micrographs than analytical methods. For this purpose, it is most convenient to use a "double stereo-gram" in which both the poles alzd the rational directions are plotted. It is, of course, necessary to orient

Jan 1, 1967

By Charles Trotter

An instrument has recently been developed for determining the inclination and azimuthal direction of boreholes. This instrument is known as the Tro-Pari Instrument and is the invention of C. Trotter and G. Pajari of Sudbury, Ontario. Description The instrument is characterized by a unit mounted in gimbals and provided with a clockwork mechanism to clamp a compass to indicate azimuthal direction and simultaneously to clamp the unit in its plumb position to indicate inclination (Fig I). By means of a timing ring suitably calibrated in 5-min divisions, the unit may be set to lock after a lapse of time sufficient to allow the placing of the instrument at the desired point in the drill hole where readings are to be taken. The maximum time Lapse obtainable with the instrument designed for use in EX or AX size holes is I hr 30 min which is considered to be ample time to lower to the greatest depths that may be drilled with this size of equipment. Larger sizes could be developed for larger diameter holes such as BX and NX sizes or the larger oil-well sizes and a correspondingly greater time lapse could be provided for. Up to the present time only the EX-AX size has been built. Operation Assuming a borehole is to be surveyed at 1000-ft depth and assuming it will take 30 min to lower the instrument to this depth, the timing ring is rotated through seven divisions which represent a time lapse of 35 min (5-min leeway) and is then returned to its zero position. This operation imparts energy to a spring which drives the clockwork mechanism. Simultaneously the compass needle is freed to swing to its magnetic north-south position and the encased mechanism is freed to hang plumb within a semicircular portion of the frame which is graduated in degrees after the fashion of a protractor. This semicircular protractor portion has a V-shaped notch at each degree division of its inner periphery. The instrument, now in its free position, is inserted in a bronze container made to suit the size of hole to be surveyed (Fig 2). Soft rubber washers are provided within the container to prevent undue shock. The container is connected to the drill rods with three 5-ft lengths of brass or aluminum alloy rods separating it from the steel rods in order to prevent distortion of the magnetic field. The assembly is then lowered to the desired point where readings are to be taken and is allowed to remain at rest until a period of time has elapsed slightly in excess of the time for which the timing ring was set. In the example cited above, when the 35 min has elapsed the compass needle is locked in its north-south position and the protractor locking pin is extruded and locks in the V notch opposite its plumb position. The device may now be removed from the borehole and it will remain in this locked position in spite of jarring or shak-

Jan 1, 1949

By P. H. Bohart

THe answer to the title question will be found by considering the ultimate influence of the petroleum engineers on industry and by considering the tools with which petroleum engineers must be equipped. Some 2000 to 3000 petroleum engineers are being absorbed by the industry yearly, indicating the magnitude of influence which they may exert on the industry. The petroleum industry is a highly technical one and it is inevitable that management be entrusted more and more to executives with technical training. The industry, therefore, expects the petroleum engineering schools to provide a broad basic training and a social and economic orientation which goes beyond merely supplying the minimum technical qualifications necessary to discharge responsibilities for a particular job. Because of the many branches of industry, emphasis must be placed on the Student's being trained in fundamentals, as well as grounded in other engineering branches, such as mechanical, civil and electrical engineering. The petroleum engineering graduate must know how to outline and organize the material for an engineering report and should be thoroughly grounded in English, both written and spoken. Even to the end that a five-year course may be required, they should receive instructions in auxiliary cultural and social science courses, industrial relations, and public speaking. Training in the method of approach to an engineering problem is something in which industry is deeply interested. A standard of ethics, a desire to arrive at the truth, and leadership training should be stressed. Introduction The basis of an an to any ques- tion concerning the petroleum engineering schools' responsibility to the industry will be found by considering the ultimate influence of the petroleum engineers on the industry and by considering also the tools with which petroleum engineers must be equipped in order to achieve success and happiness in the role in which their training, individual talents and choice of a profession ultimately will cast them. The problem must always be considered as it relates to a large group and not as it relates to a particular individual possessing strong natural talents and destined, by virtue of them, to pursue a certain course. The question implies that petroleum engineering schools have a responsibility, and indeed they do, not only to the industry but also to the students and even to the public. Because the responsibility is concentrated in a relatively few schools whose graduates are absorbed largely by the one industry, the responsibility is more apparent and the effect of failure to discharge the responsibility fully is more serious than the effect of similar failure on the part of schools supplying a smaller portion of the industry's intake of engineering graduates. This fact is especially true with respect to an industry such as the petroleum industry whose ratio of technical to nontechnical employees is relatively high and is increasing.

Jan 1, 1948