Search Documents

Jan 1, 1962

By J. Szekely, V. Stanek

Steady state heat transfer and fluid flow rates are predicted for the counter-current contacting of gas and solid streams. For a .fixed pressure drop across the bed the convective heat transfer rate is affected by the gas flow rate, which in turn is affected by the temperature distribution in the system. Variations in bed voidage and in particle size were found to change the predicted temperature profiles quite markedly, in particular when the thermal capacities of the gas and solid streams were equal. IN Part I we examined the effect of step and pulse changes in the inlet gas temperature on transients in the flow of gases through fixed packed beds. Here we shall discuss heat flow and fluid flow interactions in the counter-current heat exchange between packed solids and a gas stream. Counter-current heat exchange in packed beds has been extensively studied. In his now classical paper, Furnas' assumed constant property values and developed a simple analytical. expression for the temperature profiles in the gas and in the solid stream. A highly sophisticated analysis of counterflow systems, allowing for transients and interparticle conduction was developed by Amundsen. In preparing a very readable review of this topic Elliott' also presented a number of elegant solutions, including the case involving heat generation. A great deal of work has been done on the application of these concepts to the modelling of the blast furnace. However, in all this previous work the mass flow of the gas was regarded as a quantity independent of the gas-solid heat exchange process. In the following we shall consider counter-current heat exchange between a gas stream and a packed bed of solids, under conditions where the pressure drop across the bed is specified, rather than the mass flow of the gas. FORMULATION Consider a packed bed, extending from y' = 0 to y' = L, in which moving solids and a moving gas are contacted in a counterflow arrangement. Let cold solids, with an initial temperature Tsi and mass flow GA, enter at y' = L, and hot gas with an initial temperature of Tgi and mass flow Gg enter at y' = 0. In contrast to the problems considered in Part I this system has a nontrivial steady state and we shall restrict our attention to the study of the pressure drop flow relationships and the resultant temperature distributions for steady state conditions. Under these conditions the formulation of the problem requires the statement of the following: 1) heat balance on the gas 2) heat balance on the solids 3) the mechanical energy balance equation and in addition the knowledge of the equation of state, and a functional relationship between viscosity and temperature and an expression for the heat transfer coefficient in terms of the other parameters. On neglecting temperature gradients within the solids and for a constant mass flow of the gas, the solution to this problem is well known.'" The expressions for the temperature profiles of the gas and solid streams may be put in the following form: where Tg and T, denote the dimensionless gas and solid temperatures respectively, y is a dimensionless distance, and R is the ratio of the thermal masses. These quantities are defined as follows: For the particular case of equal thermal mass capacities by the gas and the solid, that is R = 1, the Eqs. [1]and[2] simplify to Eqs. (71 and[8], respectively: i.e., the resultant profiles are linear. As for most practical cases , solutions given by Eqs. [7] and [8] will contain only the inlet temperatures as parameters. For a fixed, predetermined value of C;b the above

Jan 1, 1970

By Claiborne C. Van Zandt

THE heavy postwar demand for Portland Cement has created shortages that are gradually being overcome by increases in plant capacity. In the post-war period, the Lone Star Cement Corp. has expanded several of its existing 15 plants and has built 2 new plants, now in operation, with a third new plant under construction in Brazil, of design somewhat different from that of the two preceding ones. The new domestic plants are located at Lone Star, Va., near Roanoke, and at Maryneal, Tex., near Sweetwater, and went into operation during 1951. Each plant is equipped with two rotary kilns and has an initial capacity of 1,500,000 bbl per year, or 6,000,000 sacks. The total cost of each plant was about $10,500,000, and on this basis $7.00 in 1951 money are required per bbl of annual capacity; at 376 lb per bbl, this corresponds to $37.00 per ton of output. The investment corresponds to approximately $80,000 per hourly-wage earner employed. The purpose of this paper is to describe the most interesting design features of the two new and almost identical Lone Star plants. Why the Dry Process Was Chosen The two new domestic Lone Star mills employ the dry process because: 1-The raw materials at both properties are particularly suitable and can be dried very, readily. 2-The Maryneal, Tex., plant does not have water available for slurry. 3-Very substantial kiln fuel savings can be obtained. 4-Dry raw grinding reduces ball and liner wear and- general maintenance, without any sacrifice in power. Operating costs to date have more than justified the choice of the dry process for these two plants. Raw Materials The chemical composition of Portland Cement raw material after crushing, grinding, and mixing, but before burning, is about as follows: [ ] sometimes tailings from an iron ore concentrating plant. Certain objectionable materials occur in raw mix: magnesia, limited in cement to 5 pct, in excessive amounts; alkalies, as sodium and potassium; phosphorous; and sulphur, generally present in coal and oil. The Roanoke raw, materials are dense limestone and shale. The Maryneal materials are soft limestone and a hard brittle clay that can be handled much like shale. Sand and iron ore are required in small quantities. General Plant Layout and Construction The two plants are so similar that one joint description will cover both, with such exceptions as will be especially indicated. The crushing plant is located in the quarry, and raw material is conveyed by belt to the storage building, where all materials are stored and handled. Fig. 1 identifies the various structures of the Roanoke plant. The large storage building is used for the storing and handling of all materials, including limestone, shale, sand, iron ore, coal, clinker, and gypsum. Directly adjoining the storage building is a structure under a similar arched roof, containing the raw and clinker grinding departments and the electrical substation. The discharge ends of kilns and coolers, and coal or gas burning equipment are also placed at one end of the mill building. The 340ft long kilns extend away from the main buildings to form the long leg of an L, at the end of which is the feeding and kiln dust collecting equipment, and the raw blending silos are conveniently located adjacent to the feed end of the kilns. The machine shop, storeroom, electrical shop, foremen's office, service rooms, and meeting hall are combined in one structure in the center of the plant, and the office and laboratory are close by. The cement silos and packhouse do not have to be tied directly into the manufacturing process and are therefore located at a point convenient to the railroad tracks.

Jan 1, 1952

By L. W. Page

PrEvious to the introduction of the motor vehicle the broken stone or macadam' road met the conditions of rural horse-drawn traffic better than any other type of road, but under fast motor traffic it has been proved to be quite unsatisfactory, and necessitates high maintenance charges. Such a road depends for its success upon the fact that the rock dust fills the voids between the stones and acts as a cement or binder. Under ideal conditions it should be constructed of rock so suited to the volume and character of horse traffic that only enough fine dust is worn from the stones of which the road is composed to take the place of that carried off by wind and rain; and when these conditions are met, the fine dust resulting from the wear of traffic forms with the stone a smooth, impervious shell, shedding the surface water and protecting the foundation. With increase in the number and speed of motor vehicles, however, it was soon found that the cost of maintenance also increased, until at the present day highway engineers consider the old method of constructing and maintaining broken-stone roads increasingly inadequate, and are introducing every known type of binding material other than rock dust to cement the stone together. Among the most prominent types of products in use are those produced from our various petroleums. That the value of modern methods of road preservation was appreciated in this country much earlier than we have been accustomed to believe is demonstrated by the recent revival of an old patent which was granted to one John Martineau, of Elbridge, N. Y., in 1834. Petroleum had, of course, not been discovered at that time, but he claims as his invention and improvement "The application of tar, turpentine, or any of that class of tenacious, cohesive substances, reduced before use to a fluid state, and that state used as a cement, to apply to, and combine with sand, gravel, pebbles, and pulverized stone, such as is used for a Mc-Adam road, or cobble stone, the interstices of coarser material being in all cases filled,'as well as may be, with sand and gravel and cemented with tar or turpentine, to form the wearing face or surface of streets,

Jan 1, 1915

By Francis C. Blake

Although the use of gaseous fuel in blast-furnaces has been often proposed, I hope the description of a very simple, yet practical and valuable, application of natural gas to the smelting of lead-ores and residues, at the works of the Pennsylvania Lead Company, will prove interesting. In May, 1886, directly after replacing the use of bituminous coal at the above works by that of natural gas, half-inch pipes from a branch gas-main were inserted directly into the tuyeres of a lead blast-furnace, and through these pipes gas was delivered into the furnace, with the air-blast at a pressure a little more than double that in the tuyere-pipes. At the same time the blast-pressure at the tuyeres was increased by an amount estimated to give a sufficient air-delivery when mixed with the gas-supply. The amount of gas delivered to the furnace is easily regulated by stop-cocks at each tuyere, and is under the immediate control of the furnace manager. Upon the introduction of gas into the tuyeres of the furnace the coke charged at the mouth was reduced 30 per cent., this being the amount of coke which I thought could be advantageously replaced by gas. This first estimate has proved to be very close to the working results, though probably the average gas-consumption corresponds to a little less than 30 per cent. of the former coke used. The proportion that we use varies, with the nature of the furnaceburden, between 20 and 40 per cent. of the total fuel. We have used 60 per cent. of gas; but there is difficulty in keeping a cool furnace-mouth when the proportion is so high. With some residues, notably metallic drosses containing some zinc, we have found it best not to use over 20 per cent. gaseous fuel. The percentage used with ore-charges has generally been higher than that used in smelting the higher-lead charges of residues from our refining works. It results from this use of natural gas that the temperature of the hearth is under almost immediate control, and, for this reason chiefly, a cleaner and more uniform slag can be run, and the furnaceworking can be made more nearly independent of the effects of atmospheric conditions or the variable moisture in the furnace-burden.

Jan 1, 1887

By L. O. Bieber, L. H. Martin

DIFFERENT MELTS OF THE same type of nickel and high-nickel alloys, while having almost identical mechanical properties at room temperature, may have widely varying hot malleability. Either the upper limit or burning temperature may vary or a variation in malleability may occur within the temperature limits normally encountered during hot working. Melts which have reduced hot malleability of the latter type, are said to have a "hot short" range. Examination of melting records and chemical analysis of these heats fails in most cases to show the reasons for these variations. In May, 1930, an investigation was started to determine if a quick and accurate method of hot-malleability testing could be developed which would predict the ability of the metal to withstand hot forging and hot rolling by standard mill practices. The results obtained were so satisfactory that from that time on, all melts of nickel and high-nickel alloys produced in the International Nickel Company's Huntington, W. Va. Works have been tested when hot malleabilty was an important factor. To date, over 63,000 commercial melts of Monelt † nickel, Inconel† and other high-nickel alloys have been tested and the test data compared with processing results. As the result of experience gained in over sixteen years, two standard methods of hot malleability testing have been adopted.

Jan 1, 1948

SECTION I Page Page Manuscript Closing Date, Febru- Forthcoming Meetings xxvii ary Meeting v . Library xxviii New York Section War Meeting on Membership xxxii Ferro-Alloys v Biographical Notices: Minutes of Meeting, Board of Robert Bell, by F. D. Adams. xlix Directors xvii H. J. Cantwell, by H. A. Members in Military Service xviii Wheeler 1 Personal xxiii Institute Committees Iii Employment xxv Officers and Directors Ix

Jan 11, 1917

By L. J. Buteau, R. E. Reed-Hill, W. A. Slippy

In a zirconium {1121} twins tend to have coherelzt boundaries and thus do not usually taper to a point when they intersect a grain boundary. Under the proper conditions, a (1121) twin may deform a boundary in such a manner as to clearly rcveal the twinning shear. Measurements of these grain-bounrlary rotatzons yield a value of 0.63 for the (1151) twinning shear. The magnitude of the observed shear and its shear sense are in excellent agreement with the assumption that the second undis-torted plme (K2) for this form of twinning is the basal plane (0002). The present value of the tzvinninz shear, which is approximately three limes larger than Rapperport&apos;s value? is in excellent agreement with reported results of Sokuskii and Prolsenko.5 RECENTLY westlake&apos; reported a study of the twinning modes of zirconium based on ~ap~er~ort&apos;s2 values for the twinning elements. He observed that two of the modes, (1012) and {1122), can be explained by relatively simple dislocation models. A workable model for (1121) twinning, however, proved to be very complex and questionable. Because Rapperport&apos;s second undistorted plane, (K2), for (1121) twinning has large indices, {ll2l6), it is possible that the difficulty in defining a model for (1121) twinning lies in an incorrect value for K2. A measurement of this twinning element has therefore been made, using a method based on observations of the shear displacement of grain boundaries at positions where they are intersected by (1121) twins. EXPERIMENTAL PROCEDURES The zirconium specimens were deformed in tension on an Instron machine either at the temperature of liquid nitrogen (77ºK), or prestrained at liquid nitrogen temperature and then further deformed at room temperature. Straining at 77°K was employed in order to nucleate (1 121) twins in large numbers, since simple ropm-temperature tensile deformation favors (1012) twinning. Specimens were machined from 1/2-in.-thick plate. The material was arc-melted sponge zirconium annealed to an ASTM grain size 4 and containing, in parts per million, 380 Fe, 880 0, <40 Hf, 32 N, and < 5 H. The specimen gage length and diameter were 1.25 and 0.130 in., respectively. To insure a gage section initially free of twins, the last 60 thousandths of the specimen diameter was removed by acid machining.

Jan 1, 1963

By T. S. Lundy, R. E. Pawel, F. R. Winslow, C. J. McHargue

The volume-diffusion coefficients of Nb-95 and Ta-182 in niobium have been measured over the temperature range 878° to 2400°C. High-temperature specimens (T 21500°C) were sectioned by conventional lathe and grinding techniques while low-temperature specimens were sectioned by an anodizing and stripping technique previously described. Over a range of more than ten orders of magnitude in diffusivity, the self-diffusion data is well-represented by the equation: D = (1.1+ 0.2) exp [- (96,000 * 900)/RT ] cm2/sec Upward deviations from this line are explained by short-circuit diffusion in combination with the loss of resolution of the sectioning techniques. Oxygen contamination within the range 100 to 450 ppm was found to have little or no effect on the self-diffusivitj 01 niobium. In a limited number of measurements, the diffusivity of Ta-182 in niobium was found to be about half that of Nb-95 in niobium. These data may be described by D = (I.0+0.90.5)exp [- (99,300 * 2400) /RT ] PREVIOUSLY reported studies of self-diffusion in niobium were by Resnick and Castleman1 and Peart, Graham, and Tomlin.2 The data of Resnick and Castleman over a temperature range 1585" to 2120°C show considerable scatter but. can be represented by D = (12.4 *0.8) exp [-(105,000+3OOO)/RT] cm2/sec The limited data of Peart, Graham, and Tomlin follow the equation D = 1.3 exp (-95,00O/RT) cm2/sec In view of recent diffusion data for ß zirconium3 and 0 titanium4 in which Arrhenius-type plots do not yield straight lines and of the potential high- temperature uses of niobium and its alloys, we thought it important to investigate the diffusion behavior of this bcc refractory metal over a large temperature range. This has recently been done for molybdenum,5 chromium,6 vanadium,"" and tantalum.9 Niobium was a particularly suitable material for this study largely because of the development of an anodizing and stripping sectioning technique which enables diffusivities as small as l0-19&apos; sq cm per sec to be determined accurately.10 In addition to self-diffusion data, data were obtained for the diffusion of Ta-182 in niobium and for the effect of varying oxygen content on self-diffusion. I) EXPERIMENTAL PROCEDURE Materials. The niobium was obtained from three sources: 1) melting stock from Shieldalloy Corp., 2) electron-beam melted single crystals, 1/2 in. diameter, from Semi-Elements, Inc., and 3) oxygen-doped, electron-beam melted single crystals from Materials Research Corp. The melting stock was electron-beam melted and specimens 5/8 in. diameter by 1/2 in. long were machined from the center of the bar. The analysis supplied by the vendor and an interstitial analysis of one of the specimens are given in Table I. The single crystals (type 2 above) were cut with a jeweler&apos;s saw to specimens about 3/8 in. long. The interstitial analysis of this material is given in Table 11. This material was used

Jan 1, 1965

By James E. Lawver

A SURVEY of Minerals Beneficiation Div. membership indicated genuine interest in automatic process control, but revealed that the average mill is operating with a minimum of self-regulating devices. Apparently, the mill operators are content to continue without controls until the practicality of self-regulating devices is more generally accepted, or, in the opinion of the writer, until automatic controls become a necessity to meet economic demands of product quality and cost. Both to stimulate interest in control, and to solicit publication of technical know-how by members and equipment manufacturers, this paper presents a cross section of control problems in two general categories: (a) Control problems that can usually be solved by reference to the literature, i.e. controls that have proven successful in the mineral or chemical industries; (b) Problems that are troublesome and frequently unsolved due to unavoidable adverse conditions in the mill circuit to be controlled.

Jan 10, 1953

By H. E. Sadler, Prof. Silliman

The research here recorded was undertaken early in the present year, and has been prosecuted steadily for about eight months. While the work has been under my constant supervision and advice, the labor has all been performed by Mr. Sadler, to whom is chiefly due the development of the successive steps which have led to the final result. The process is better than I dared to hope, and we are able to place at the command of chemists and engineers interested in the matter an apparatus of continuous and uninterrupted action, and methods of analysis by which the daily averages of the two variable and inconstant factors of illuminating gas, ammonia and sulphur, may be determined with all needful accuracy, even by those little skilled in chemical manipulation, and with very little loss of time. This research has been carried out in the laboratory of the New Haven Gaslight Company.

By C. W. Kempton

IF New England were located in some distant and almost inaccessible region, there is no doubt that its mineral resources would have been ere this well developed and generally acknowledged, but laboring under the disadvantage of nearness, it has been neglected. Its surface, moreover, is not cut up by mountains and canons, and the remnants of many of the old ridges are extensively covered by glacial drift. Having for the past ten months been engaged in the development of a. mineral district in Southeastern Maine, I would take this opportunity to lay before the Institute sketches of results, and try to give some idea of the formations as found. The Sullivan Mining District extends from the town of Franklin, through Hancock, Sullivan, and Gouldsborough, from northwest to southeast, about sixteen miles. A general idea of this locality may be gathered from the map accompanying. (Fig. 1).

Jan 1, 1879

By W. H. Triplett

Silver-lead-zinc replacement deposits occur in limestones of the anticlinal Caja range at Providencia, near Avalos, Zacatecas, Mexico. The description deals with intrusives, outcrops, preferred horizons, changes from bedding to fracture, control in depth, and variations in abundance and ratios of minerals throughout a vertical range of 500 m. THE purpose of this paper is to record a few field observations and accumulated office data concerning outcrops, relation of ore occurrences to intrusive and host rock, and mineral zoning. Reasons for some of the phenomena are not clear to the author so the facts are given with the hope that other investigators may be able to furnish the explanations. The Avalos unit of the Compania Minera de Penoles, S. A., operates the Alicante, Bonanza, Providencia, Albarradon, San Eligio, Nazareno, Leona, Salaverna, and Santiago mines situated between Avalos railroad station and Concepcion del Oro on the Coahuila and Zacatecas railroad in the State of Zacatecas, Mexico. Some of these mines are within Penoles property while others are on mining claims leased from the Compania Nazareno y Catasillas, S. A., Mazapil Copper Co., and the American Smelting and Refining Co. The main office and camp are at Providencia, about 170 km southwest of Monterrey, N. L., so the silver-lead-zinc mines of the district are usually referred to as the Providencia mines. The Aranzazu, Catarroyo, and Cabrestante copper-gold mines are situated a few kilometers to the southeast on the same mountain range near Con- cepcion del Oro, the name by which the camp is known. It is operated by the Mazapil Copper Co. The main theme in the following pages is a description of the silver-lead-zinc ore occurrences of the district. Rock Formations Sedimentary Rocks: Many competent geologists have contributed generously to an ample fund of information concerning the sedimentary columns of northern Mexico. Among them are Carlos Burck-hardt, E. Bose, L. B. Kellum, and R. W. Imlay. Carlos Burckhardt, who covered a number of extensive areas in many parts of the Mexican Republic, devoted years to mapping the geology of the Caja, Zuloaga, and Santa Rosa mountain ranges around Mazapil, Concepcion del Oro, and San Pedro de Ocampo, Zacatecas. He did most of the original mapping which has been used as a basis and amplified by others. C. E. Burbridge and, more recently, John

Jan 1, 1953

By W. H. Triplett

Silver-lead-zinc replacement deposits occur in limestones of the anticlinal Caja range at Providencia, near Avalos, Zacatecas, Mexico. The description deals with intrusives, outcrops, preferred horizons, changes from bedding to fracture, control in depth, and variations in abundance and ratios of minerals throughout a vertical range of 500 m. THE purpose of this paper is to record a few field observations and accumulated office data concerning outcrops, relation of ore occurrences to intrusive and host rock, and mineral zoning. Reasons for some of the phenomena are not clear to the author so the facts are given with the hope that other investigators may be able to furnish the explanations. The Avalos unit of the Compania Minera de Penoles, S. A., operates the Alicante, Bonanza, Providencia, Albarradon, San Eligio, Nazareno, Leona, Salaverna, and Santiago mines situated between Avalos railroad station and Concepcion del Oro on the Coahuila and Zacatecas railroad in the State of Zacatecas, Mexico. Some of these mines are within Penoles property while others are on mining claims leased from the Compania Nazareno y Catasillas, S. A., Mazapil Copper Co., and the American Smelting and Refining Co. The main office and camp are at Providencia, about 170 km southwest of Monterrey, N. L., so the silver-lead-zinc mines of the district are usually referred to as the Providencia mines. The Aranzazu, Catarroyo, and Cabrestante copper-gold mines are situated a few kilometers to the southeast on the same mountain range near Con- cepcion del Oro, the name by which the camp is known. It is operated by the Mazapil Copper Co. The main theme in the following pages is a description of the silver-lead-zinc ore occurrences of the district. Rock Formations Sedimentary Rocks: Many competent geologists have contributed generously to an ample fund of information concerning the sedimentary columns of northern Mexico. Among them are Carlos Burck-hardt, E. Bose, L. B. Kellum, and R. W. Imlay. Carlos Burckhardt, who covered a number of extensive areas in many parts of the Mexican Republic, devoted years to mapping the geology of the Caja, Zuloaga, and Santa Rosa mountain ranges around Mazapil, Concepcion del Oro, and San Pedro de Ocampo, Zacatecas. He did most of the original mapping which has been used as a basis and amplified by others. C. E. Burbridge and, more recently, John

Jan 1, 1953

By W. A. Forbes

PAGE Introductory............357 ReasoNs for Gas Cleaning.........358 First Methods of Separation of Dust.......359 Amount of Dust Produced by the Blast Furnaces of the United States Steel Corporation During 1912.....359 Dust Content in Blast-Furnace Gas.......360 Primary Cleaning. Dry Cleaning: General Remarks..........360 Braasert- Witting Whirler........362 Brassert Modifications of Brassert-Witting Whirler....363 Dyblie Whirler..........363 Remarks on Efficiency of Dry Cleaning......366 Wet Cleaning: Zschocke System..........367 Duquesne Tower..........367 Bian Gas Washer..........369 Final Cleaning. Wet Cleaning: Theisen Gas Washer.........371 Theisen Disintegrator Gas Washer.......372 Schwerz-Bayer Disintegrator Gas Washer..... 374 Fowler & Medley Vertical Gas Washer......376 Feld Gas Washer..........377 Reco Centrifugal Gas Washer........379 Sepulchre Gas Washer.........381 Dry Cleaning: Halberger-Beth Gas-Cleaning System......382 Smith.Bagley Gas-Cleaning System,......384 Howard Dust Separator.........387 Possible Separation of Dust by Electrical Precipitation ... 389 KapnOGraph............389 Methods of Determining DUst in Gas.......389 Advantages of Clean Gas.........393 Introductory. During the early stages of blast-furnace practice. the gas formed in the furnaces by the combustion of the coke used in smelting the ores was allowed to escape into the atmosphere. The light furnished

Jan 1, 1914

By Allen L. Hatch

A survey of all phases of the world&apos;s lead and zinc production in 1968 from ore through to refined metal was conducted by sending questionnaires to individual companies and the results of this survey are tabulated at the end of the paper. The paper goes on to review changes in the geographical distribution of the world&apos;s lead and zinc mine and metal production and in the trading patterns of raw materials, present and future utilization of metal production capacity, developments in metal smelting and refining processes and the growing importance of marketing, product development and research in the 1950&apos;s and 1960&apos;s.

Jan 1, 1970

By C. K. Leith

Jan 1, 1906

By A. R. Elsea, E. E. Fletcher

Cast X-40 alloy with the lowest nitrogen content studied had a 100-hr rupture stress at 1500°F about equal to the reported value for the commercial alloy. Increases in nitrogen content progressively decreased the rupture strength, and with about 0.1 to 0.2 pct N a minimum strength was reached, but there was no accompanying change in microstructure. Further increases in nitrogen resulted in the fomzation of progressively increasing amounts of a lamellar, pearlitic-type structure at the grain boundaries, with accompanying increases in rupture strength, and above about 0.25 to 0.33 pct N, the rupture strength exceeded the normally reported values. Two series of melts representing different melting stocks exhibited minimum rupture strengths at different nitrogen contents. This suggests that some unidentwed trace element not removed by vacuum melting has a strong influence on the response of this alloy to variations in nitrogen content. In a series of melts with manganese contents ranging from 0.6 to 3.2 pct, the material with the lowest manganese content had the highest 100-hr rupture strength at 1500°F. The manganese variations had no appreciable effect on the microstructure. CAST cobalt-base alloys such as X-40* exhibit high strengths at elevated temperatures (1500°F and above), but they also show considerable scatter in high-temperature properties. Since the design of parts for critical applications must be based on the minimum expected properties, this broad scatter appreciably lowers the design strength of the alloy. If the relatively poor properties exhibited by a few test parts from any given group could be improved, the spread in properties would be narrowed, and the design stress could more closely approach the average expected properties. The purpose of this research investigation was to learn what were the causes of these erratic properties and, if possible, to find methods for eliminating them. Earlier unpublished work showed that vacuum melting markedly influenced the high-temperature strength of cast X-40 alloy. There were indications that this behavior may have been the result of changes in the nitrogen or manganese content of the castings. Consequently, in the current investigation, the influence of variations in nitrogen and manganese content on the structure and high-temperature properties of cast X-40 alloy was studied. In this program, X-40 melting stock was vacuum melted to produce a base material that was very low in nitrogen content and in volatile trace elements. Additions were then made to this base material to produce alloys of the desired composition. The metal was cast into investment molds producing coupons which were machined into stress-rupture bars. These bars were subjected to stress-rupture tests and me-tallographic study to determine the influence of changes in analyses (nitrogen and manganese content) on the structure and properties. Material—The melting stock used for these experi-ments was in the form of shot from two master heats of commercial X-40 alloy. Only one master heat was used in a given series of melts. Thus, any differences in structure or properties that showed up in the specimens from a given series would be the result only of the intended variations in composition. The certified analyses of the master heats were as follows: C Mn Si Cr Ni Lot No. 2 0.50 0.71 0.66 25.44 10.53 Lot No. 3 0.54 0.73 0.70 25.95 10.00 W Fe Co P S Lot No. 2 7.45 1.34 Bal. 0.011 0.013 Lot No. 3 7.58 1.53 Bal. 0.005 0.016

Jan 1, 1960

EXECUTIVE COMMITTEE OF THE BOARD OF DIRECTORS M. L. Haider, Chalrman Phillp Kraft, Vice-Chairman T. B. Counselman Evan Just J. B. Morrow FINANCE COMMITTEE OF THE BOARD OF DIRECTORS Gall F. Moulton, Chairman L F Remartz I W M. Peirce INVESTMENTS Erle V. Daveler, Chalrman, &apos;54 Henry Rrumb, &apos;53 W. M. Peirce, &apos;55 Gall F. Moulton, ex officu, Chairman, Finance Committee Andrew Fletcher, ex offrcio Treasurer, AIME

Jan 1, 1952

By R. H. Rice

Turbo blowers for blast-furnace blowing have now been in use for some years, and a review of the experience gained and the present state of progress may be interesting.

Jan 1, 1915