Search Documents

Iowa State College Ames, Iowa Iowa State Mining Society CARL S. NELSON, President NORMAN S. GEIST, Secretary K. A. PHILLIPS, Faculty Sponsor C. G. DRESSER, Counselor University Of Kansas Lawrence, Kansas University of Kansas Student Chapter of A.I.M.E. WALTER CROOK, President EDWARD C. MISHOU, Secretary E. A. STEPHENSON, Faculty Sponsor GEORGE M. FOWLER, Counselor K. A. SPENCER, Counselor .

Jan 1, 1942

By Walter Crafts, C. M. Offenhauer

In a previous study of the carbide phase of chromium steels, it was shown that chromium carbide (Cr7C3) is 2 more stable carbide than cementite (Fe3C) at tempering temperatures above about 500°C. in quenched steels containing from about I to 7.5 per cent chromium. Below this temperature the carbide phase was found to consist of cementite in all of the steels examined. In the present investigation it was found that a similar change in the carbide phase takes place in molybdenum and in chromium-molybdenum steels at approximately the same tempering temperatures. The approximate ranges of occurrence of the alloy carbides Cr7C3, Cr4C, and Mo2C have been determined in steels containing up to 5 per cent chromium, I per cent molybdenum and 0.60 per cent carbon. The experimental steels were made in small high-frequency furnaces from Armco ingot iron, low-carbon ferrochromium and calcium molybdate and were poured into 2-in. ingots, which were forged to I-in. round bars. Sections of the bars were heated to the carbide-solution temperature and cooled rapidly to induce austenite transformation at relatively low temperatures. The steels were subject to some segregation, therefore comparatively high temperatures were necessary to dissolve all of the carbides. The microstructure of the quenched specimens was examined to verify the belief that the carbides had been dissolved, and also to determine the nature of the nonmartensitic structure of incompletely hardened steels. Ferrite and pseudo-martensite were present in some of the specimens, but all specimens were quenched at such a rate that pearlite was not formed, in order to ensure the formation of the carbides at temperatures lower than about 500°C. It had been found previously1 that in chromium steels the chromium carbide could be produced by transformation of austenite in the pearlite range above 500°C., and, in order to start the tempering treatment with the carbide present as cementite, the absence of pearlite was considered to be essential. The specimens were tempered for 64 hr. to permit the formation of the stable carbide. After tempering, the specimens were submitted to microscopic and X-ray examination. The carbides were separated either electrolytically in a 5 per cent HCl electrolyte or with an acidified copper-potassium chloride solution. The crystal structure of the carbide phases was determined by the Debye-Scherrer type of X-ray patterns. The X-ray patterns obtained from specimens near the boundaries between two types of carbides were generally weak and diffuse as compared with the other patterns. For this reason, and because the more soluble components may be masked, the boundaries between the phases could not be determined precisely. However, the X-ray analysis of electrolytically separated carbides has given consistently reproducible results

Jan 1, 1943

By Walter Crafts, C. M. Offenhauer

In a previous study of the carbide phase of chromium steels, it was shown that chromium carbide (Cr7C3) is 2 more stable carbide than cementite (Fe3C) at tempering temperatures above about 500°C. in quenched steels containing from about I to 7.5 per cent chromium. Below this temperature the carbide phase was found to consist of cementite in all of the steels examined. In the present investigation it was found that a similar change in the carbide phase takes place in molybdenum and in chromium-molybdenum steels at approximately the same tempering temperatures. The approximate ranges of occurrence of the alloy carbides Cr7C3, Cr4C, and Mo2C have been determined in steels containing up to 5 per cent chromium, I per cent molybdenum and 0.60 per cent carbon. The experimental steels were made in small high-frequency furnaces from Armco ingot iron, low-carbon ferrochromium and calcium molybdate and were poured into 2-in. ingots, which were forged to I-in. round bars. Sections of the bars were heated to the carbide-solution temperature and cooled rapidly to induce austenite transformation at relatively low temperatures. The steels were subject to some segregation, therefore comparatively high temperatures were necessary to dissolve all of the carbides. The microstructure of the quenched specimens was examined to verify the belief that the carbides had been dissolved, and also to determine the nature of the nonmartensitic structure of incompletely hardened steels. Ferrite and pseudo-martensite were present in some of the specimens, but all specimens were quenched at such a rate that pearlite was not formed, in order to ensure the formation of the carbides at temperatures lower than about 500°C. It had been found previously1 that in chromium steels the chromium carbide could be produced by transformation of austenite in the pearlite range above 500°C., and, in order to start the tempering treatment with the carbide present as cementite, the absence of pearlite was considered to be essential. The specimens were tempered for 64 hr. to permit the formation of the stable carbide. After tempering, the specimens were submitted to microscopic and X-ray examination. The carbides were separated either electrolytically in a 5 per cent HCl electrolyte or with an acidified copper-potassium chloride solution. The crystal structure of the carbide phases was determined by the Debye-Scherrer type of X-ray patterns. The X-ray patterns obtained from specimens near the boundaries between two types of carbides were generally weak and diffuse as compared with the other patterns. For this reason, and because the more soluble components may be masked, the boundaries between the phases could not be determined precisely. However, the X-ray analysis of electrolytically separated carbides has given consistently reproducible results

Jan 1, 1943

J. S. Unger,* Pittsburgh, Pa. (written discussion?).-I heartily agree with the author's suggestion, near the close of the paper, that greater uniformity in the making and use of brick is desirable. The effect of the manner of laying the brick, the mortar or cement used, the necessity of standardizing the shapes, the elimination of irregular or poorly designed brick, and the necessity for uniform operating conditions were pointed out by me some years ago. Many factors influence the quality of firebricks. The following figures obtained from bricks during their making or after completion show the need for greater uniformity in their quality. These results were obtained from regular commercial bricks, shipped to the consumer. In many cases the samples were from the same car load.

Jan 11, 1919

By H. C., Weed

THE Inspiration Consolidated Copper Co., located in the Globe-Miami district at Inspiration, Ariz., became a producer of copper in 1915. From 1915 until 1948, 116,278,000 tons of ore were produced from underground workings by the block-caving system of mining. In April 1948, open-pit ore production from portions of the ore body was started and earlier plans for block-caving in these areas were abandoned. The change was due to economic conditions. Prior to the war years Inspiration's costs of mining by block-caving methods were comparable to, or even below, the costs of some open-pit operations. By the end of the war these conditions were completely changed. Underground costs had risen steadily for labor and supplies. Difficulty was being experienced in finding competent underground men and underground development was almost hopelessly behind schedule. On the other hand, open-pit costs had been sharply reduced through the development of modern earth-moving machinery and plenty of labor was available for surface work.

Jan 1, 1950

A meeting of the New York Local Section of the American Institute of Mining Engineers, in joint session with the American Electrochemical Society, was held at the Engineering Societies Building, 29 West 39th Street, New York City, Nov. 20, 1913. Mr. Lawrence Addicks, Chairman of the American Electrochemical Society, presided at the meeting, in conjunction with Mr. Louis D. Huntoon, Chairman of the New York Local Section of the American Institute of Mining Engineers. The Chairman announced the subject to be discussed it the meeting as follows: As this is a joint meeting of the New York Sections of the Electro-chemical Society and the Institute, Mr. Huntoon has insisted that I share the responsibilities of the chair to the extent of introducing the speakers.

Jan 1, 1914

By H. Conrad, K. Janowski, E. Stofel

In a previous paper,1 the occurrence of (0001) and (0111) twins was reported for compression tests of 60-deg-oriented sapphire rods in the temperature range from 1100° to 1300° C. Subsequent to this initial work, additional tests have been conducted, and twinning has been found to occur at temperatures as high as 1500° C. Also, the temperature and strain-rate conditions for the two types of twins and for slip have been established in more detail. The present note covers this more recent work. The compression-test data are summarized in Table I. The techniques for identifying the twins are optical examination up to X1000 and X-ray analysis.' It is evident that (0711) twins are pre-

Jan 1, 1965

In opening the meeting I wish to express my greatest pleasure at being able to greet this joint session of the Mining and Electrical Engineers. As engineering develops, we find that the border lines between the different branches of engineering become more and more indistinct; the several fields overlap so much that they are three or four layers deep in places. It is only an accident that we couldn't have had the Mechanical Engineers also as a formal part of this gathering, because they are quite as much interested in this subject as the Electrical or Mining Engineers. A little history may enlighten some of those who have not been close to this work. A year ago last summer, there was brought to the attention

Jan 4, 1919

National Minerals Advisory Council A meeting of the National Minerals Advisory Council on August 3rd in Washington, D. C., indicated the vitally important part that the mining industry is to play in the mobilization program. Director James Boyd of the Bureau of Mines told the Council that the Department of the Interior would review the recommendations of all the Council's commodity committees with regard for mobilization planning in the light of the changed international picture. The Council was requested to reactivate its commodity committees and have them gather all available data on supplies, their sources and availability and present and potential production of the minerals and metals represented on each committee. Data on labor, machinery, transportation, automotive and stationary equipment, power, fuel, lumber, water supply are a few of the important items called for in the reports, which are to be presented at a meeting of the Council on September 1 at Salt Lake City. The material in the reports will become the basis for discussing metal and mineral requirements at that time. Discussion at the meeting bared several $64 questions, probably the most important of which are the following: 1. Which of the war-essential metals and minerals and in what quantities can we reasonably expect to get them from abroad under threat of submarines? 2. How are we going to meet the manpower problem posed by (a) migration of labor from mining to manufacturing since the end of World War II and (b) the draft and the calling up of reservists? Opinion was expressed by industry spokesman at the meeting that the function of complying with mobilization requirements be left to those in the industry itself; that is, those having the "know how." This view contended that any administrating governmental agency should be kept as small and streamlined as possible. There was general sentiment against the reactivation of the wartime Premium Price Plan or other bonus plans as a stimulus to production. The thought was emphasized that what was needed was a change in the basic conditions which have fostered the decline in domestic mining activity in the postwar years. One such condition, long overdue for correction, is the tax structure as it applies to mining enterprises. Many quarters both in industry and in government favor tax relief along the lines suggested in the six tax recommendations by the Council to the Secretary of the Interior last December. The Council adopted a resolution expressing a feeling that the following tax recommendations are still feasible and desirable and will accomplish as much toward increasing exploration for new deposits (thereby subsequently increasing production) as will government loans for exploration: (1) Losses from unprofitable ventures should be allowed corporations, partnerships, or individuals as ordinary deduction against current income. (2) Development costs after discovery should be recognized as operating expenses. (3) Allowance for depletion should be made to the stockholder as well as to the corporation. (4) Income should not be taxed without full allowance for losses of loss years. (5) Adequate allowances for percentage depletion should be made. A discussion of the manpower problem led to the Council's acceptance of a resolution advising that "military authorities should proceed with caution in depriving the mining and metallurgical industry of its manpower." The resolution strongly urged that no personnel "directly engaged in exploration, development, production or supervision (of strategic and critical materials) should be drafted for the armed forces, at least until the anticipated demands upon these producers are clarified." Stockpiles The Munitions Board's "Stockpile Report to the Congress" of July 23, 1950 revealed: (1) The total estimated value of the stockpile objective is $4,051,714,510 at the close of fiscal year 1950. (2) The total value of the stockpile on hand, at the close of fiscal 1950 was $1,556,154,352 or 38.4 pct of the total stockpile objective. An additional $494,948,060 was on order, making a total of 50.6 pct on hand plus the amount on order. (3) Materials obtained for the stockpile by the ECA from January to June 1950 amounted to $13,112,085, while development projects by ECA during this period involved the expenditure of $9,322,000, mainly with counterpart funds. Shortly after the start of the Korean conflict it was felt that Congress ould appropriate greatly increased sums for the purchase of materials for the stockpile. This stimulus to the program may increase the dollar earnings of those European nations that are present or potential contractors in our stockpiling program. Such a development would mean that these nations could add to their gold reserves, thereby stabilizing their respective economies and hastening recovery. This seems to be the picture for the next six months anyway. The "bug" appears when it is realized that the increased threat of total world war actually may retard recovery in Europe as nations on the continent may feel inclined to devote more of their resources to defense programs. Industries Essential to Defense The Department of Commerce in response to a request by the Department of Defense issued on August 3, 1950 a "Tentative List of Essential Activities" as a "guide for calling up for active duty members of the civilian components of the Armed Forces." The list includes the following: Primary Metal Industries. Included herein are establishments engaged in the smelting and refining of ferrous and nonferrous metals from ore, pig, or scrap. Metal Mining. This category includes establishments primarily engaged in mining, developing mines or exploring for metallic minerals (ores). This group includes all ore dressing and beneficiating operations. Anthracite Mining, Bituminous Coal and Lignite Mining, Crude Petroleum and Natural Gas Extraction, Mining and Quarrying of Nonmetallic Minerals, Except Fuels. Challenge to the Mining Industry The source of our country's great strength lies in its capacity to produce. In times of stress such things as national morale and manpower are all-important but without a capable industrial machine we would be helpless. That machine must be fed with minerals and metals in order to generate and maintain momentum sufficient to insure success. Consequences of the lack of adequate supplies of essential metals and minerals to increase and sustain our industrial power are not pleasant to contemplate. It is absolutely imperative that we put forth Herculean effort to guarantee ample supplies of such essential materials as copper, lead, zinc, manganese, antimony, mercury, tungsten, tin, chromite, nickel, cobalt, iron ore and rubber. The mining industry faces a challenge more serious than ever existed before in the history of our country. The industry must be equal to the task.

Jan 9, 1950

By Albert Sauveur

Some writers believe that when austenite transforms completely into pearlite on slow cooling through the thermal critical range, such transformation does not imply the formation of any of the so-called transition constituents: martensite, troostite and sorbite. Might it not be claimed with as much justification that when water freezes it does so suddenly, solid ice being obtained without passing through the intermediate stages of ice and water? Obviously, regardless of the speed of solidification, this would be erroneous. Before reaching the completed solid condition, this must of necessity pass through an unbroken series of stages when the system consists of mixtures of water and of ice, the former decreasing and the latter increasing in amount. Are not these "transitionV stages in the freezing of water similar to the transition stages occurring in the transformation of austenite into pearlite? To clarify, let us consider in Fig. 1 the mechanism of the transformation of eutectoid steel from its austenitic to its pearlitic condition as it cools slowly through its thermal critical range. It is generally admitted that this transformation is the result of two distinct phenomena: (1) the allotropic change of gamma iron into alpha iron and (2) the crystallizing out of solution of the carbide Fe3C. Whether this crystallizing of Fe3C implies also its formation is immaterial for our purpose. In other words, whether it is the carbon in atomic dispersion which is present in gamma iron or molecules of Fe3C has no bearing upon the matter to be discussed. The transformation of gamma iron into alpha iron cannot take place suddenly. It must of necessity be progressive, regardless of the speed with which it may take place. At A, for instance, there would be present AB gamma iron and BC alpha iron. The distance MN does not refer to falling temperature, but to the passage of time. It may be assumed that the transformation takes place at a constant temperature (the Ar321 point). In a similar way, the crystallization of Fe3C out of the austenite solid solution must be progressive as depicted between M and N. At A there would be present AB gamma iron, BC alpha iron, CD carbon dissolved in gamma and in alpha iron and DE Fe3C. This condition may be described according to individual preference as martensite or troostite. To sum up, can the metal pass from condition

Jan 1, 1931

By D. P. Harris

This paper surveys a few of the quantitative exploration models that might be of interest to an ex-plorationist seeking to apply methods of operations research to mineral exploration. A general development of each model is presented, and the model is evaluated relative to the exploration activity. Finally, a philosophy of exploration and mineral resources is presented, and a possible exploration strategy incorporating concepts of some of these models consistent with this philosophy is proposed. The high cost of conducting an effective exploration program has generated an increasing interest in methods of optimizing the allocation of the resources of a firm engaged in mineral exploration. As a step towards this, mathematical models have been formulated which are designed to quantify those variables of mineral exploration in such a manner that they can be integrated with all phases of the firm's operations so as to optimize its profit objective. QUANTITATIVE MODELS General: Exploration models express at least two concepts: mineral occurrence and effectiveness of search. In simplest terms, an exploration model might be formulated mathematically as follows: P(X) = F(X) . G(X), where P(X) = the unconditional probability of discovery of X deposits, F(X) = the probability of occurrence of X deposits, and G(X) = the probability of discovery of X deposits, conditional upon their existence in the search area. With these general models as a basis of reference, some of the specific exploration models are examined below. The Allais Model: DEVELOPMENT - M. Allaisl performed the first study in which a philosophy of exploration was formulated into a probability framework. His objective was to estimate the economic profitability of the exploration of the Algerian Sahara. Allais divided the Algerian Sahara into blocks of land (called cells) 10 km square and defined the random variable, X, as the number of mining districts per cell. Thus, F(X) would describe the probability of 1, 2, or n mining districts occurring within any cell of the search area. Allais reasoned that his best information as to the form of the distribution, F(X), was the number of mining districts per cell that had been found in well explored areas in the world, such as the Western States of the U.S. He found that the Poisson function produced a reasonably good fit to the distribution of districts in these explored areas: where? is a parameter, such as the average number of districts per cell. Thus, by determining the value

Jan 1, 1968

By AIME AIME

SECTION DELEGATES were given an opportunity to see how the machinery of Institute administration functions, on Tuesday evening, Feb. 16, when they were the' guests at the regular monthly meeting of the Directors. Of the new board of 25 members, 19 were present at the meeting, including directors from Seattle, Los Angeles, Wyoming, Oklahoma, Chicago and Pitts-burgh, the new junior past-president from Jerome, Ariz., and the new president from .Washington, D. C. The complete list of the 72 in attendance at the dinner,: held in the main dining room of the Engineers' Club, which pre-ceded the general session of the Directors'. meeting, follows:

Jan 1, 1932

By W. H. Smith

IN the course of an investigation on chromium containing minor amounts of alloying elements, the information herein has been obtained on the crys-tallographic orientations resulting from arc melting, rolling, and annealing. The chromium used in this investigation was electrolytic flake obtained from the Electro Metallurgical Co. This material was heated for 20 hr at 1600°C in hydrogen with a dew point of about — 100°C. The oxygen and nitrogen content of the chromium after this treatment was 0.0003 pct 0 and 0.005 pct N. Five pounds of this chromium were arc melted in a water-cooled copper crucible. After arc melting, the oxygen and nitrogen contents were 0.002 and 0.025 pet, respectively. A section of this ingot is shown in Fig. 1. By means of a back-reflection Laue technique, the crystal habit of the cast ingot was determined. As expected, it was found that the [loo] was approximately the axis of the columnar grains. In this respect, chromium behaves like other body-centered-cubic metals in that a cubic axis is normal to the cold surface of the mold. A slab cut from this ingot was rolled at 600°C as follows: four 30 pct reductions were made with intermediate anneals at 1200°C for 15 min. Rolling was done with the [loo] of the columnar grains in the rolling direction. Following the final anneal, an 80 pct reduction was taken at 600 °C. The final sheet thickness was ten mils. By polishing and etching, the thickness was reduced to four mils and the grain orientation determined by the transmission Laue method using molybdenum radiation with a zirconium filter. Fig. 2 is the (110) pole figure for this material with the ideal (100) [011] and (111) [112] orientations indicated. The orientation is typical of most cold rolled body-centered-cubic metals having the [llO] of the grains approximately in the rolling direction and the (100) planes approximately in the plane of the rolled sheet. There is also evidence of some 10) [1 orientation. The grain orientation of sheet rolled 40 and 80 pct in the same direction as before at 600°C followed by recrystallization at 12000 C for 15 min was determined by a back-reflection Laue technique. A random texture was found in both cases. This 1200°C 15 min anneal was found to give complete recrystallization and some grain growth.

Jan 1, 1956

By Irwin Roman

In addition to projects such as those reported in parts I and II above, the Section of Geo-physics of the Federal Government has undertaken a considerable amount of fundamental research. Two such field-projects may be mentioned, one a magnetometric study in the Comstock Dis-trict of Nevada, and the other a resistivity-study of snow and ice. In addition to the field-problems, there have been two classes of research of a mathematical type. One of these has been the preparation of tables, scales, and charts for the important geophysical functions already known; the other has been the extension of the relations involved in the resistivity-problem. The magnetometric study at Spring Valley, in the Comstock District, was made for the pur-pose of determining the value of the magnetometer in extending the knowledge of a region, as ob-tained by purely geological means. The variations in the vertical magnetic intensity were mea-sured with an Askania balance at intervals of 20 feet, along lines as shown in Figure I.. These lines were 100 or 500 feet apart over an area approximately a rectangle 6000 by 7500 feet. In addition to the lines shown, two areas were selected for more intensive study. In one, short

Jan 1, 1940

By W. H. Adams

During the years when Americans were most active in investigations of the many substances containing nitrogen or ammonia, viz.: 1869 to 1875, my connection with certain chemical industries led me to experiments in the direction of the recovery of wastes from coal-gases. I take from my notes such memoranda as I think will be of interest, in the hope that some benefit may be derived therefrom by engineers at present attempting to utilize the waste products from coke-oven and blast-furnace gases. An examination of the conditions governing the manufacture of gas along the Atlantic seaboard, and an intimate knowledge of the mine-products used by the different large works, naturally led me at first to consider the well-known foreign methods of concentrating the available soluble salts in a modicum of water. The result was sufficiently promising to warrant a full line of experiments. At that time, no attention seemed to have been paid to the values of " gas-liquors." Nearly every gas-works in the United States wasted its wash-water in the sewers. The nitrogen in bituminous coals varies in quantity from 0.75 to 1.50 per cent. of the total weight. In the process of distillation in

Jan 1, 1887

By Walter Rose

Experimentation which measures differences in pressure across the interfaces of immiscible fluids in the interstitial spaces of porous media may be termed "capillary pressure experimentation". In the literature of petroleum technology since 1941 there have appeared twelve papers popularizing capillary pressure concepts and developing applications of these concepts for the solution of problems of practical reservoir engineering importance, such as the determination of connate water, fluid distribution. in transition zones, reservoir rock textural properties, and oil recovery from petroleum reservoirs. Although a review of the literature would be justified at this time in order to reconcile the conflicting viewpoints which are contained in the cited papers, the object of this note will be of more limited scope. It is believed that the recent paper of Muskat alls sufficient attention to many of the uncertainties which arise upon examination of the published literature. such that until satisfactory counter-proposals can be made it will serve our purpose only to mention some other like uncertainties. This will emphasize further the need confronting petroleum technologists to re. consider and reformulate the application possibilities of capillary pressure experimentation. In particular, I sug- gest that we examine the thesis that capillary pressure experimentation as above defined can lead to measurements reflecting the recovery of oil from petroleum reservoirs, as was proposed first" by Amyx and Yuster and was first reduced to practice by the experimentation of Welge . In fact. I shall deal exclusively with the Welge papers since it is the principle one on this subject which has appeared to date. I shall attempt to show that the possibility of describing oil recovery features in terms of capillary pressure phenomena has not been established entirely. The Welge paper was a pioneering effort to evaluate this recovery application possibility. P. P. Reichertz' comments on the Welge paper state that non-wetting phase discontinuities are developed occasionally in the Welge experiment, and restate Muskat's argument that discontinuous fluid elements (partially saturating the interstices of porous media which are elsewhere saturated with some other immiscible phase or phases) are not subject to the requirements of hydrostatic equilibrium. It is the purpose of my comment to show that it is unnecessary to make Reichertz' postulation regarding non-wetting phase discontinuities (however valid) when it is desired to criticize Welge's theoretical treatment of his problem. It can be shown that Welge's method of measuring values for ''capillary pressure" is invalid in many instances of application, such that his reported curves of capillary pressure Versus fluid saturation often have no physical meaning, even throughout the interval of fluid saturation where it might be otherwise suspected that no phase discontinuities occur. By considering established principles of capillary pressure experimentation it can be shown that the pressure difference experimentally observed between wetting and non-wetting fluid phases which are contained in external reservoirs will reflect on the capillary pressure difference at the interfaces of contact between these phases only when the following conditions are satisfied: (a) There shall be a balance between the opposing forces of gravity and capillarity, as obtains under conditions of hydrostatic equilibrium when the positions of the interfaces of contact become fixed in pore spaces of certain geometry (b) The wetting and non-wetting fluids within the interstitial spaces shall everywhere be continuous with the external wetting phase reservoir and the external non-wetting phase reservoir, respectively. It will become apparent immediately that in any instance when a greater pressure is recorded in the external wetting phase reservoir than in the external non-wetting phase reservoir, one may establish either that static equilibrium has not been attained or that discontinuities in one or more of the fluids have been developed. This is because the pressure otherwiee is always gereatest in the non-wetting phase at each static interstitial interface of contact with the wetting phase. such that the externally measured pressure in the non-wetting phase likewise must be greatest if the above conditions are to be satisfied.

Jan 1, 1949

By Walter Rose

Experimentation which measures differences in pressure across the interfaces of immiscible fluids in the interstitial spaces of porous media may be termed "capillary pressure experimentation". In the literature of petroleum technology since 1941 there have appeared twelve papers popularizing capillary pressure concepts and developing applications of these concepts for the solution of problems of practical reservoir engineering importance, such as the determination of connate water, fluid distribution. in transition zones, reservoir rock textural properties, and oil recovery from petroleum reservoirs. Although a review of the literature would be justified at this time in order to reconcile the conflicting viewpoints which are contained in the cited papers, the object of this note will be of more limited scope. It is believed that the recent paper of Muskat alls sufficient attention to many of the uncertainties which arise upon examination of the published literature. such that until satisfactory counter-proposals can be made it will serve our purpose only to mention some other like uncertainties. This will emphasize further the need confronting petroleum technologists to re. consider and reformulate the application possibilities of capillary pressure experimentation. In particular, I sug- gest that we examine the thesis that capillary pressure experimentation as above defined can lead to measurements reflecting the recovery of oil from petroleum reservoirs, as was proposed first" by Amyx and Yuster and was first reduced to practice by the experimentation of Welge . In fact. I shall deal exclusively with the Welge papers since it is the principle one on this subject which has appeared to date. I shall attempt to show that the possibility of describing oil recovery features in terms of capillary pressure phenomena has not been established entirely. The Welge paper was a pioneering effort to evaluate this recovery application possibility. P. P. Reichertz' comments on the Welge paper state that non-wetting phase discontinuities are developed occasionally in the Welge experiment, and restate Muskat's argument that discontinuous fluid elements (partially saturating the interstices of porous media which are elsewhere saturated with some other immiscible phase or phases) are not subject to the requirements of hydrostatic equilibrium. It is the purpose of my comment to show that it is unnecessary to make Reichertz' postulation regarding non-wetting phase discontinuities (however valid) when it is desired to criticize Welge's theoretical treatment of his problem. It can be shown that Welge's method of measuring values for ''capillary pressure" is invalid in many instances of application, such that his reported curves of capillary pressure Versus fluid saturation often have no physical meaning, even throughout the interval of fluid saturation where it might be otherwise suspected that no phase discontinuities occur. By considering established principles of capillary pressure experimentation it can be shown that the pressure difference experimentally observed between wetting and non-wetting fluid phases which are contained in external reservoirs will reflect on the capillary pressure difference at the interfaces of contact between these phases only when the following conditions are satisfied: (a) There shall be a balance between the opposing forces of gravity and capillarity, as obtains under conditions of hydrostatic equilibrium when the positions of the interfaces of contact become fixed in pore spaces of certain geometry (b) The wetting and non-wetting fluids within the interstitial spaces shall everywhere be continuous with the external wetting phase reservoir and the external non-wetting phase reservoir, respectively. It will become apparent immediately that in any instance when a greater pressure is recorded in the external wetting phase reservoir than in the external non-wetting phase reservoir, one may establish either that static equilibrium has not been attained or that discontinuities in one or more of the fluids have been developed. This is because the pressure otherwiee is always gereatest in the non-wetting phase at each static interstitial interface of contact with the wetting phase. such that the externally measured pressure in the non-wetting phase likewise must be greatest if the above conditions are to be satisfied.

Jan 1, 1949

Addicks, L Ambler, J O Anderson, F B Armstrong, T Allen, L M, Jr Arnold, C E Adams, C E Adams, R E Anderson, A J Booth, E L Bernhardt, D I Boyd, W S Browning, W C Blake, D E Black, T B Bergman, Julius Bowen, H P Beckett, P G Blickensdefer, F C Bond, Josiah Butler, P P Bondlas. Y

Jan 1, 1923

By Titus Ulke

About two years ago, in making an examination of the Etta mine for the Harney Peak Tin Co., I discovered, in a vertical secondary quartz-vein in the granite massive of Etta mountain, the mineral about to be described. The vein was from a few inches to 3 feet wide, and was exposed for a length of about 15 feet. It was

Jan 1, 1893

By George W. Orton

i\- number of investigations have established that tungsten monocarbide (WC) forms throughout a wide range of temperatures (800° to 2200°C), but the di-tungsten carbide (W2C) forms only at the high end of this temperature range.1"7 In addition the decomposition of WC into WzC and C at elevated temperatures has been observed.8"10

Jan 1, 1964