Search Documents

By R. C. Edwards, T. G. Kirkland, Will Mitchell

A scrubber of new design has been invented for the beneficiation of glass and chemical sands. The machine is described and its capacity and metallurgical efficiency compared with the performance of other sand cleaning devices. THREE years ago, when the Process Research Laboratory at Allis-Chalmers Manufacturing Co. sought a remedy for the increasing cost of disposing of great quantities of spent sands from foundries, R. C. Edwards developed a continuous inclined paddle scrubber which removed a substantial amount of the charred coatings from the grains with a surprisingly small amount of degradation of the sand itself.' The satisfactory results obtained on foundry sand, using this piece of equipment in conjunction with classification, suggested that a similar procedure could probably be applied to the cleaning of other sands, such as those required by the glass and chemical industries. This paper describes the flowsheet and the results of tests performed on impure natural sands. The four materials tested were silica sands obtained from widely separated geographical areas. Three of the sands tested contained various amounts of iron oxide and the fourth an excessive amount of calcareous bonding material. The iron oxide was present predominantly in the form of grain coatings, which were scuffed by the paddle scrubber, and in all cases a product was manufactured which would meet one of the sets of specifications imposed by the glass industry.' The Edwards paddle scrubber used in these tests consists of a rubber-lined steel cylinder 18 in. in diam and 48 in. long, mounted on a frame so that its slope can be varied 5" to 35" from horizontal. This variable slope permits controlled flow of material through the machine. Rubber paddles rotate inside the cylinder and are secured to a center shaft 2 in. square, which extends through the entire length and is turned at both ends so that it can be supported by sleeve bearings centrally fixed in the end plates of the shell. At the upper or feed end it extends through the bearing on the end plate into a sheave, to which the motor drive is connected by means of Texrope transmission. The four sets of paddles mounted on the shaft, two in each set, are made of rubber belting, 1/4 in. thick, 9 in. wide, and 16 in. long. The two paddles in each set are secured on opposite sides of the square shaft, but in the same longitudinal position along the shaft axis. In other words, the two paddles in the set operate 180" apart. Each successive set is mounted 90" from the preceding one. One end of each paddle is bolted to the square shaft and the other weighted by a steel bar, lx1 1hx9 in. long, which is attached about Yz in. from the outer tip of the paddle. By centrifugal force at proper shaft speed, these weights force the paddle surface to rub smoothly against the rubber lining of the cylinder. During operation, the sand forces its way between the paddle face and the surface of the cylinder, providing the necessary abrading action as the pulp flows by gravity down the length of the cylinder. The capacity of the machine is limited by the amount and the hardness of the coating material and by the quality of product desired. The degree of scrubbing is governed by the retention time in the scrubber, which in turn may be changed by varying the feed rate, water content of the feed, and

Jan 1, 1953

By R. C. Edwards, Will Mitchell, T. G. Kirkland

A scrubber of new design has been invented for the beneficiation of glass and chemical sands. The machine is described and its capacity and metallurgical efficiency compared with the performance of other sand cleaning devices. THREE years ago, when the Process Research Laboratory at Allis-Chalmers Manufacturing Co. sought a remedy for the increasing cost of disposing of great quantities of spent sands from foundries, R. C. Edwards developed a continuous inclined paddle scrubber which removed a substantial amount of the charred coatings from the grains with a surprisingly small amount of degradation of the sand itself.' The satisfactory results obtained on foundry sand, using this piece of equipment in conjunction with classification, suggested that a similar procedure could probably be applied to the cleaning of other sands, such as those required by the glass and chemical industries. This paper describes the flowsheet and the results of tests performed on impure natural sands. The four materials tested were silica sands obtained from widely separated geographical areas. Three of the sands tested contained various amounts of iron oxide and the fourth an excessive amount of calcareous bonding material. The iron oxide was present predominantly in the form of grain coatings, which were scuffed by the paddle scrubber, and in all cases a product was manufactured which would meet one of the sets of specifications imposed by the glass industry.' The Edwards paddle scrubber used in these tests consists of a rubber-lined steel cylinder 18 in. in diam and 48 in. long, mounted on a frame so that its slope can be varied 5" to 35" from horizontal. This variable slope permits controlled flow of material through the machine. Rubber paddles rotate inside the cylinder and are secured to a center shaft 2 in. square, which extends through the entire length and is turned at both ends so that it can be supported by sleeve bearings centrally fixed in the end plates of the shell. At the upper or feed end it extends through the bearing on the end plate into a sheave, to which the motor drive is connected by means of Texrope transmission. The four sets of paddles mounted on the shaft, two in each set, are made of rubber belting, 1/4 in. thick, 9 in. wide, and 16 in. long. The two paddles in each set are secured on opposite sides of the square shaft, but in the same longitudinal position along the shaft axis. In other words, the two paddles in the set operate 180" apart. Each successive set is mounted 90" from the preceding one. One end of each paddle is bolted to the square shaft and the other weighted by a steel bar, lx1 1hx9 in. long, which is attached about Yz in. from the outer tip of the paddle. By centrifugal force at proper shaft speed, these weights force the paddle surface to rub smoothly against the rubber lining of the cylinder. During operation, the sand forces its way between the paddle face and the surface of the cylinder, providing the necessary abrading action as the pulp flows by gravity down the length of the cylinder. The capacity of the machine is limited by the amount and the hardness of the coating material and by the quality of product desired. The degree of scrubbing is governed by the retention time in the scrubber, which in turn may be changed by varying the feed rate, water content of the feed, and

Jan 1, 1953

By R. C. Edwards, Will Mitchell, T. G. Kirkland

A scrubber of new design has been invented for the beneficiation of glass and chemical sands. The machine is described and its capacity and metallurgical efficiency compared with the performance of other sand cleaning devices. THREE years ago, when the Process Research Laboratory at Allis-Chalmers Manufacturing Co. sought a remedy for the increasing cost of disposing of great quantities of spent sands from foundries, R. C. Edwards developed a continuous inclined paddle scrubber which removed a substantial amount of the charred coatings from the grains with a surprisingly small amount of degradation of the sand itself.' The satisfactory results obtained on foundry sand, using this piece of equipment in conjunction with classification, suggested that a similar procedure could probably be applied to the cleaning of other sands, such as those required by the glass and chemical industries. This paper describes the flowsheet and the results of tests performed on impure natural sands. The four materials tested were silica sands obtained from widely separated geographical areas. Three of the sands tested contained various amounts of iron oxide and the fourth an excessive amount of calcareous bonding material. The iron oxide was present predominantly in the form of grain coatings, which were scuffed by the paddle scrubber, and in all cases a product was manufactured which would meet one of the sets of specifications imposed by the glass industry.' The Edwards paddle scrubber used in these tests consists of a rubber-lined steel cylinder 18 in. in diam and 48 in. long, mounted on a frame so that its slope can be varied 5" to 35" from horizontal. This variable slope permits controlled flow of material through the machine. Rubber paddles rotate inside the cylinder and are secured to a center shaft 2 in. square, which extends through the entire length and is turned at both ends so that it can be supported by sleeve bearings centrally fixed in the end plates of the shell. At the upper or feed end it extends through the bearing on the end plate into a sheave, to which the motor drive is connected by means of Texrope transmission. The four sets of paddles mounted on the shaft, two in each set, are made of rubber belting, 1/4 in. thick, 9 in. wide, and 16 in. long. The two paddles in each set are secured on opposite sides of the square shaft, but in the same longitudinal position along the shaft axis. In other words, the two paddles in the set operate 180" apart. Each successive set is mounted 90" from the preceding one. One end of each paddle is bolted to the square shaft and the other weighted by a steel bar, lx1 1hx9 in. long, which is attached about Yz in. from the outer tip of the paddle. By centrifugal force at proper shaft speed, these weights force the paddle surface to rub smoothly against the rubber lining of the cylinder. During operation, the sand forces its way between the paddle face and the surface of the cylinder, providing the necessary abrading action as the pulp flows by gravity down the length of the cylinder. The capacity of the machine is limited by the amount and the hardness of the coating material and by the quality of product desired. The degree of scrubbing is governed by the retention time in the scrubber, which in turn may be changed by varying the feed rate, water content of the feed, and

Jan 1, 1953

By Henry J. Sandri

ACQUISITION JUSTIFICATION There are many reasons why companies consider acquisitions as a means to expand their operations. Some wish to reduce the impact of business cycles on their businesses. Others seek firms within the same industry for expansion and increased market share. Still others diversify in order to avoid takeovers. Whatever the reasons or justification, an evaluation of an acquisition candidate should be systematic and thorough. To many financial managers the concept of a systematic acquisition evaluation indicates the need for a regular set of evaluation criteria. While these are available from numerous sources, one basic parameter frequently overlooked is the application of these criteria to an industry which is different from the acquirer. This becomes particularly important when evaluating firms within the mineral industry. The mineral industry is significantly different from other industries to require different valuing techniques. • This paper will present a number of reasons why an acquisition candidate in the mineral industry should be evaluated differently from other acquisitions, including by other mineral firms. Additionally, this paper will review the most appropriate means of valuing a mineral firm. • Firms considering the acquisition of a mineral firm should understand the nature of the industry before ever making a tender offer. Some of the general considerations include the following: • Level of Capital Intensity: In the mid-1980's the start up cost for a gold mine has been between 20-200 million dollars and 500-1,500 million dollars for a bauxite operation. • Global Nature of Competition: Except for certain industrial minerals, most minerals and metals are traded worldwide and many on national exchanges, such as COMEX. • Start-Up Time: Many mining operations in developed and developing countries have long lead times, 7 to 10 years in some cases, prior to the start-up of production. • Long Term Nature of Investment: For most mineral operations payback usually occurs at least 7 years after production has started. Additionally, many mining operations will continue producing for 80-100 years. • High Level of Risk: The number of factors that a mining firm cannot control such as grade, volume, world supply and demand, plus the long payback periods tend to classify mineral firms at a higher than average risk compared to other investments. • Cyclical Nature: The mineral industry is cyclical in nature, experiencing long troughs and explosive peaks, thus making timing a critical issue. • Labor Intensive: Even with the large capital requirements needed to operate a mine, most mines are labor intensive in proportion to their capital equipment. • Location: Obviously, the nature of this industry requires operators to work in difficult locations, frequently far from civilized localities, in poor weather conditions and without proper supply and distribution infrastructure. One of the most important considerations is an understanding of asset replacement and asset value. Unlike manufacturing concerns, firms in the mineral industry are working toward the elimination, through depletion, of their asset base. Product flexibility is not available to a mining operation. A mineral firm basically has two options as its resource base is depleted: 1) replace the asset with new production, or 2) deplete the asset and close down operation, as in the South African gold mining model referred to later in this paper. An understanding of the

Jan 1, 1985

By Orson Cutler Shepard

The term "electrocapillary amalgamation" is used in this paper to designate amalgamation processes that depend upon electrocapillary phenomenon; i.e., the action of an electric current upon the surface tension of mercury at the contact with aqueous solutions. Electro-capillary amalgamation is selected as a name for these processes because the electrocapillary phenomenon has been found to be the effective agent in the use of sodium amalgam, as well as in the various processes using an electric current from a source outside of the amalgam. Amalgamation processes that depend upon supplying an electric current to the amalgam from an outside source, such as batteries and generators, have previously been called electrical amalgamation processes. There has been a tremendous amount of experimental work done on amalgamation processes involving the use of an electric current, as shown by the large number of patents issued on these processes: the earliest in 1885 and the latest in 1934l. Regardless of all the experimental work, the fundamental principles causing the operation of electrocapillary amalgamation processes have not been described. The explanation usually given is that an electric current keeps the amalgam bright and clean. Patent No. 328532 states: It is well known that when amalgam plates are used for collecting gold and silver from their ores the surfaces of these plates are liable to become tarnished or sickened by certain substances contained in the ores or in the current of water which is employed to carry the ore over the plates, and that in this condition they are unfitted for amalgamating the particles of gold and silver. To prevent this and to keep the surfaces of the amalgamation plates always bright and in a better condition for catching and amalgamating the particles of gold and silver I employ electricity in the following manner: . . . A similar explanation is given 49 years later, in patent No. 1953364: The sodium (Na) ions lose their charge at the cathode becoming sodium atoms, which do not react with the electrolyte, but follow the grounded electrical current through the mercury body producing in their passage sodium amalgam and liberate themselves in the amalgamation compartment when brought in contact with the fed

Jan 1, 1939

By Orson Cutler Shepard

The term "electrocapillary amalgamation" is used in this paper to designate amalgamation processes that depend upon electrocapillary phenomenon; i.e., the action of an electric current upon the surface tension of mercury at the contact with aqueous solutions. Electro-capillary amalgamation is selected as a name for these processes because the electrocapillary phenomenon has been found to be the effective agent in the use of sodium amalgam, as well as in the various processes using an electric current from a source outside of the amalgam. Amalgamation processes that depend upon supplying an electric current to the amalgam from an outside source, such as batteries and generators, have previously been called electrical amalgamation processes. There has been a tremendous amount of experimental work done on amalgamation processes involving the use of an electric current, as shown by the large number of patents issued on these processes: the earliest in 1885 and the latest in 1934l. Regardless of all the experimental work, the fundamental principles causing the operation of electrocapillary amalgamation processes have not been described. The explanation usually given is that an electric current keeps the amalgam bright and clean. Patent No. 328532 states: It is well known that when amalgam plates are used for collecting gold and silver from their ores the surfaces of these plates are liable to become tarnished or sickened by certain substances contained in the ores or in the current of water which is employed to carry the ore over the plates, and that in this condition they are unfitted for amalgamating the particles of gold and silver. To prevent this and to keep the surfaces of the amalgamation plates always bright and in a better condition for catching and amalgamating the particles of gold and silver I employ electricity in the following manner: . . . A similar explanation is given 49 years later, in patent No. 1953364: The sodium (Na) ions lose their charge at the cathode becoming sodium atoms, which do not react with the electrolyte, but follow the grounded electrical current through the mercury body producing in their passage sodium amalgam and liberate themselves in the amalgamation compartment when brought in contact with the fed

Jan 1, 1939

By E. P. Fleming

COMPARED to the situation abroad, the domestic industry continues to lag both as regards the production and consumption of newly mined lead. During 1938 we produced and consumed slightly over 20 per cent of the world output, whereas ten years ago the figure was nearly double this pro- portion. Labor difficulties and absence of demand were chiefly responsible for the general inactivity. In the foreign field, in spite of low metal prices, production and consumption of lead equaled or exceeded all previous records. Practically all the large companies, with the exception of those in Spain, increased operations, though it should be noted that the foreign lead mines have higher-grade ores than domestic mines. In view of the rapid expansion of the foreign industry, it is natural to expect greater progress abroad, particularly in process metallurgy.

Jan 1, 1939

By Joseph W. Roe, L. L. HEWES

A GRAPHIC solution of Kutter's formula for the flow of water has been worked out By Dr. L. I. Helves in connection with his course in Graphic Computations, given in the Sheffieild Scientific School, Yale University, which may be of interest to those who deal with canals, flumes and streams.

May 1, 1909

By David Keys

THE actual procedure in estimating depth of overburden from mag-netic observations made on the surface will vary with the form of the deposit and any theoretical discussion will apply only so far as the form of the deposit conforms to the mathematical premises on which the theory is based. Since the shapes of natural deposits in the field cannot be expressed rigorously in mathematical form, the best that can be done is to assume some simple form and deduce results. Fortunately many small variations in form produce only slight changes in the estimated depth of overburden, therefore the methods have a definite practical value. For the theoretical treatment, magnetic ore deposits may be divided roughly into three classes, depending upon whether the magnetic anom-alies may be considered to arise from (1) a single magnetic pole, (2) a dike or (3) a magnetic doublet. Particular cases, falling under one or other of these classes, have been discussed by different authors.1-4 In general, it may be stated that when the magnetic effects as measured on the surface are due only to one pole of the body, the other pole being so remote that its effect may be neglected, the resultant anomaly F at any point will vary as the inverse square of the distance r of the point from the pole, which may be expressed mathematically by F = k/r2, where k is a constant. When the deposit occurs in the form of a long, thin dike, the resultant anomaly will be of the form F = k'/r and when the deposit is in the shape of a lens, so that both poles have an appreciable effect on the surface, the result will be similar to that caused by a magnetic doublet, and the form will be F = k'/r3. The particular class under which a deposit falls may be deduced from the results of the magnetic survey. The second class is readily found, but there may be difficulty in deciding between the first and third. Isody-namic contours of both the vertical and horizontal anomalies will often be a good guide in making a correct decision.

Jan 1, 1937

By William M. Sheehan

TRANSPORTATION is one of the most important problems of the mine operator and the possibilities of cost reduction in this field should not be overlooked. In the railroad industry, cars and locomotives have been improved greatly, and the progress there made is well worthy of study by the mine operator looking for maximum efficiency in every branch of his activities. One of the outstanding developments in the construction of railroad equipment in recent years has been the wide-spread adoption of large one-piece steel castings for the framework of locomotives, passenger and freight cars. Some of the advantages and applications of this type of construction will be outlined in this paper, with particular thought of the needs of the mining industry. The inherent qualities of cast steel: homogeneity, unrestricted size and shape, high tensile strength, flexibility of metal distribution, resistance to corrosion, and gracefulness of outline, make it the most versatile member of the ferrous group. Not only is it a strength-giving element, but it is corrosion resistant, a combination that makes for large economies in equipment maintenance. Flexibility of metal distribution allows the integral foundation to be in the shape best suited for the purpose. These cast structures are really assembled in the mold in liquid form and the metal can be placed in the right pro¬portion exactly where it is needed, thus securing weight economy and uniformity of fibre stress. Such a process permits the incorporation, with ease, of necessary brackets, utilizing them to provide not only greater strength for the derail part itself, but often to add to the value of the entire unit. Laps, seams, and joints, which are necessary in all fabricated forms, are eliminated.

Jan 1, 1933

By J. F. Harvard

We might say that for the metallurgist time "ambles withal," for the mining engineer time "trots withal," and for the geologist, time "gallops withal." And anyone for whom time "stands still withal" does not belong in the mining community today! In this bicentennial year of the United States of America we sense the mystery of time and we feel the pulse of history, especially in our own profession. What was mining like 200 years ago? What is it like today? What will it be like 200 years in the future?

Jan 7, 1976

By Alexander Squire

A BRIEF study of the effects of material and processing variations upon the tensile properties of steel formed from mixtures of iron and carbon was made in order to provide information regarding the .properties obtainable in iron-carbon compacts as influenced by forming pressure, sintering temperature, and graphite particle size. Sintered steels formed from mixtures of iron and graphite have been studied by Stern,1 who investigated the effect of various percentages of graphite on compacts formed from electrolytic iron that were repressed and heat-treated after sintering. A further study, by Stern and Greenberg,2 is concerned with the heat-treatment of steels formed by the carburization of iron compacts, and Margolies3 has reported work on the simultaneous sintering and carburization of iron-powder parts. Glauch4 investigated the effect of various types of graphite on the properties of iron-carbon powder alloys but did not determine the effect of different particle sizes of the same graphite alloyed with different types of powder. In the investigation reported in this paper, powders typical of those produced by electrolytic deposition and the decarburization of shotted steel scrap were used. The powders were mixed by tumbling in a jar mill with graphite powder ground to an average particle diameter of 2, 4, 6, and 16 microns (as determined by microscopic measurement). The properties of the iron and graphite powders are presented in tabular form as Table I. In order to obtain the maximum information from a minimum number of test specimens, the study was divided into two sections with one set of specimens treated identically in each section as a basis for comparison. In the first section, iron powder produced by the shotting and subsequent decarburization of scrap steel was mixed with 2-micron graphite powder, pressed at 50,000, 100,000, and 200,000 psi, and sintered in hydrogen at 1200°C for the periods of time ranging from 15 to 120 minutes. In the second section of the investigation, electrolytic iron powder was mixed with graphite of an average particle diameter of 2, 4, 6, and i6 microns, pressed at 100,000 psi, and sintered at temperatures ranging from 1000° to 1200°C. for periods of time of 30 to 180 minutes. By following this procedure an indication of the effect of the following variables upon the density and tensile properties of iron-carbon powder compacts was obtained: (I) forming pressure, (2) sintering time, (3) particle size of graphite powder, (4) sintering temperature, (4) type of iron powder.

Jan 1, 1947

R. C. Canby, Wallingford, Conn. (communication to the Secretary*). —Apropos of the experimental reduction of copper from cuprous chloride by fusion with ground limestone and colre, as described by Messrs. Laist and Frick, and also proposed for use at Chuquicamata, it might be of interest to refer bricfly to the experience at Argentine, Kan., in the smelting of the suboxide of copper (as produced in the Hunt and Douglas process) containing appreciable quantities of chlorides. In the Engineering and Mining Journal of June 10, 1911,I gave some account of what had appeared to be crucial difficulties with the Hunt and Douglas process, and how the filter-press difficulty had been so rapidly overcorne after my discovery of the effect of the sodium salts in the leaching solutions. I also described the effect of the cupola-furnace gases upon the lime rock with which I had replaced the coke in the absorption tower, which apparently showed the presence of considerable chlorine, due to the imperfect conversion of the subchloride to suboxide, as well as that due to the difficulties of washing thoroughly the suboxide with the means provided, and also to the presence of chlorides in the cement copper which was smelted with the suboxide. The fumes from the cupola, when issuing direct into the atmosphere, were very dense and white, except when a hot furnace top caused a reddish tinge due to dust. These fumes had a peculiarly suffocating effect, SO that when they were blown over into the town the population suffered the greatest actual distress, not the mere annoyance which would have been due to a disagreeable odor. The absorption tower had been built at the instance of the city authorities to abate this nuisance, and not with the idea of making any additional metal savings. A serious feature in connection with the Argentine experience with the Hunt and Douglas process was, that it had been implicitly assumed that there could be no metal loss in the Hunt and Douglas process itself, and that all attempts to locate the ruinous copper losses which were accumulating in the metallurgical accounts were devoted to the roasting department. It is possibly unfortunate for metallurgical advance along these particular lines that just about the time of this discovery of this previously unsuspected volatilization loss, in the smelting of the suboxide, the Kansas City company made a contract with the Western Union Telegraph Co. for its supply of copper sulphate and the Hunt and Douglas

Jan 1, 1915

By James A. Barr

THE writer's first experience with flotation was during World War I, in the beneficiation of Alabama graphite schist ores. One plant used a cone with a peripheral overflow; dried ore was distributed by a rotating disk onto the surface of the water. No reagents were added. The flake-graphite film floated along with some fine silica. Dewatering screens separated the flake. Naturally unit capacities were low but results were satisfactory. Minerals Separation mechanical flotation machines were used in another graphite mill. Pine oil was added directly to the head cells, with very good results. All the graphite concentrates from both types of flotation were carefully refined after drying by passing through burr mills, followed by very close sizing on sifters. In March 1927, the writer ran a very successful flotation test on minus 28-mesh, deslimed, Tennessee brown phosphate "sand,"[t] using a mechanical laboratory machine built in the shops of the Anaconda Copper Mining Co., through the courtesy of Ernest Klepetko. The machine was soon converted to a subaeration type, with improved results. This phosphate research program was greatly enlarged and led to the formation of the Phosphate Recovery Corporation. The development of nonmetallic flotation followed rapidly. The first flotation machine for beneficiation of phosphate was installed in January 1928, in a pilot mill, by International Minerals and Chemical Corporation, at Mulberry, Florida. These machines were Minerals Separation, 24-in., subaeration types, with weir control of pulp between cells. The sand bleeders were very small-about 1 ¼ -in. diameter. As the feed contained 15 to 25 per cent plus 28-mesh material, the cells choked up frequently. This was corrected by cutting a 2 by 6-in. bleeder opening above the impellers, at grid level, which short-circuited the coarse fractions directly into the feed of the next cell. The matter of size classification and grinding was a considerable problem, which does not come within the scope of this article. Because of the troubles noted above, cascade-type roughers were installed in the second flotation plant, built about 1930. Experimental cells had been tried in 1928. General plant layout is shown in Fig. I and details of the cascade construction in Fig. 2. The cascade installation in plant No. 2 gave good results and eliminated troubles due to choke-ups and coarse feed. The capacities and metallurgical results equaled those of the modified 24-in. Minerals Separation flotation machines in plant No. I The objections to the cascade installation are the floor space and mill height required. In 1939 an improved Minerals Separation machine was tested in parallel with the cascades. Extensive tests indicated

Jan 1, 1945

By Charles Janin

ONE of the most interesting features of the world's platinum situation has been the steady increase of Russian production, which had dropped to 11,000 oz. in 1920, but increased to 92,000 oz. in 1926, and to probably over 100,000 oz. for 1927. It is ex-pected that Russian production of platinum will, be-fore long, closely equal its pre-war production, or approximately 200,000 oz. annually. The world production before the war was around 250,000 oz.; that for 1925 has been estimated at 160,000 oz., and for 1926 probably 170,000 oz. The consump-tion of platinum has, however, decreased. The esti-mate of the International Selling Agency was a de-mand of 130,000 oz. new platinum against a normal pre-war demand of over 200,000 oz. The high price of platinum during the war gave an added impetus to the search for substitutes for the metal, and sev-eral were developed that are now used extensively in place of platinum. The demand for platinum for high-class jewelry, however, was not greatly affected by the high prices, but "white" gold did replace platinum in the cheaper jewelry. Colombia is the most important producer of plati-num, next to Russia, and the production has increased from around 10,000 oz. pre-war production to 55,000 oz. or more in 1927. In 1924 important discoveries of platinum were made in South Africa. Prior to these discoveries practically all platinum was recovered from alluvial deposits, and the South African opera-tions are first to work an ore profitably for the pri-mary recovery of platinum. A number of companies were formed to develop these deposits, but only a few made any real progress. Total production for 1926 was about 5000 oz. The United States production is unimportant; that in Canada has increased to around 9000 oz., principally as a by-product in nickel-copper ores.

Jan 5, 1928

By Warren E. Wilson

The transportation of solids in pipe lines is a matter of deep concern in many fields of engineering. Much experimental and theoretical work has been done in an effort to devise means of designing pipe lines that will satisfactorily transport given solid loads, but there remain many unanswered questions in this field. The present discussion will be confined to a rather narrow portion of this field and will endeavor to point out certain factors that may well be considered when comparing the relative economy of various installations. The data have been presented previously but a new interpretation was prompted by a suggestion in a paper by Professor O'Brien,1 of the University of California, that the friction work per pound of dry material should be considered in determining the relative efficiency of various installations. This method of considering relative economy in various pipe lines leads to some rather unexpected conclusions, especially with reference to the economy of large pipe sizes. A previous suggestion by the writer3 concerning the economy of a rather peculiar type of installation is strengthened. It is not believed that the considerations set forth herein apply directly in the case of dredge lines, where economy is largely a matter of a high rate of pumping in order to reduce the unit overhead charge. However, it is believed that some value may be gained from these considerations in cases involving the disposal of a fixed amount of solids per unit time with a minimum expenditure of energy and at a low cost for replacement of worn pipes. Such situations are not uncommon in the disposal of mill tailings and the disposal of solids deposited from irrigation waters. It was found that data leading to general conclusions for various pipe sizes were not available but certain definite trends are indicated and methods of analyzing available data are presented in the hope that they may be of assistance in preparing engineering estimates on designs of pipe lines of the type described above. Energy Requirements Carrying out the idea contained in ' Professor O'Brien's paper concerning the method of computing energy required to transport solids, the following analysis leads to some rather interesting conclusions. Let us represent: Solids load in term of mass per unit time by W Ratio of mass of suspended solids to total mass of mixture flowing by p Volume rate of flow of mixture by Q Length of pipe by L slope of energy grade line by s Mass per unit volume of solids by m. Mass Per unit volume of liquid by mi Mass per unit volume of mixture by mm We then have as an expression for the solids load: W = pQmm The work done per unit mass, P, on the mixture to move it along the pipe the

Jan 1, 1948

By Warren E. Wilson

The transportation of solids in pipe lines is a matter of deep concern in many fields of engineering. Much experimental and theoretical work has been done in an effort to devise means of designing pipe lines that will satisfactorily transport given solid loads, but there remain many unanswered questions in this field. The present discussion will be confined to a rather narrow portion of this field and will endeavor to point out certain factors that may well be considered when comparing the relative economy of various installations. The data have been presented previously but a new interpretation was prompted by a suggestion in a paper by Professor O'Brien,1 of the University of California, that the friction work per pound of dry material should be considered in determining the relative efficiency of various installations. This method of considering relative economy in various pipe lines leads to some rather unexpected conclusions, especially with reference to the economy of large pipe sizes. A previous suggestion by the writer3 concerning the economy of a rather peculiar type of installation is strengthened. It is not believed that the considerations set forth herein apply directly in the case of dredge lines, where economy is largely a matter of a high rate of pumping in order to reduce the unit overhead charge. However, it is believed that some value may be gained from these considerations in cases involving the disposal of a fixed amount of solids per unit time with a minimum expenditure of energy and at a low cost for replacement of worn pipes. Such situations are not uncommon in the disposal of mill tailings and the disposal of solids deposited from irrigation waters. It was found that data leading to general conclusions for various pipe sizes were not available but certain definite trends are indicated and methods of analyzing available data are presented in the hope that they may be of assistance in preparing engineering estimates on designs of pipe lines of the type described above. Energy Requirements Carrying out the idea contained in ' Professor O'Brien's paper concerning the method of computing energy required to transport solids, the following analysis leads to some rather interesting conclusions. Let us represent: Solids load in term of mass per unit time by W Ratio of mass of suspended solids to total mass of mixture flowing by p Volume rate of flow of mixture by Q Length of pipe by L slope of energy grade line by s Mass per unit volume of solids by m. Mass Per unit volume of liquid by mi Mass per unit volume of mixture by mm We then have as an expression for the solids load: W = pQmm The work done per unit mass, P, on the mixture to move it along the pipe the

Jan 1, 1948

By A. C. Stevenson

THE hoisting equipment selected for use at the Hecla mine in 1907 was one of the first Ilgner type Ward-Leonard controlled hoists put into ser- vice. Development of the Hecla below the 2000-ft. level, which is the ultimate depth of the old equipment, and the additional service required by the "Star," necessitated additional hoisting capacity. It will be our endeavor to give j70u a brief summary of the engineering which determined the selection of the new equipment. The engineer in making his decision as to size, speed, etc., must .make a duty study approximating as closely &s possible the actual opePating conditions which will eventually result. Primarily, it is necessary to know what work must be done. The amount of material which must be hoisted under the maximum condition, as well as its distribution from the various levels of the mine was carefully studied by the mining engineering department, as the ore reserves, their relative-position and the probable method of working them had to be considered. The final figures reached, taking into consideration four different operating conditions, were, in tons per day, as follows:

Jan 1, 1930

By T. Imaizumi

Covering the whole scope of the MMIJ activities, i.e. geology and exploration, mining, mineral processing, and metallurgy, the technical innovations and improvements since 1972 were reviewed. Special references were made to the MMIJ Research Committees which were subsidized by the Japan Mining Promotive Foundation, in connection with those activities.

Jan 1, 1976

By John J. Stokes

Literature on the electrolysis of aluminum from cryolite melts and on the structure of these melts is surveyed critically. Data on density, freezing point, and other properties are reviewed. Theories of the electrolysis are examined in the light of these data. Two theories are presented which account equally well for the observations. * * * * In the early days, the process was thought of as a simple one. The actual mechanisms must be tremendously more complex. This paper is devoted to a rather narrow part of the whole subject, namely, what ions are present in the bath, and by what mechanism the current is carried.

Jan 4, 1958