Search Documents

By R. I. Jaffee, J. G. Dunleavy, W. Hodge, H. R. Ogden

IN a search for an improved conductor for use in field wire for the L. S. Army Signal Corps, an alloy of copper and silver was developed from which it was possible to obtain 29 B & S ga. strands with tensile strengths in excess of 160,000 psi combined with an electrical conductivity of over 70 pct IACS. Such a favorable combination of strength and electrical conductivity has not been reported previously in the rather extensive literature covering this subject. The properties obtained from various binary alloys of copper and silver, together with the method of fabrication of these alloys which has been developed to obtain the properties desired in fine wire strands, are discussed in this paper. LITERATURE The effect on the electrical conductivity of copper of the various elements in solid solution is shown in Fig I, taken from published data by J. O. Linde and others.' It will be noted that silver in solid solution depresses the electrical conductivity to a lesser extent than any other element for which data are given, and is followed rather closely by cadmium, and then by chromium. Zinc, which lies between cadmium and chromium, has so high a solid solubility in copper that the data for zinc are scarcely comparable to the data for the other two in the range covered. Not many data are available on the strain hardening of copper-rich Cu-Ag alloys. Corson2 reports a 3 pct Ag alloy properly cold worked and annealed to have 100,000 psi tensile strength and 90 pct IACS conductivity. On straight cold working, Hessenbruch3 reports 101.000 psi for a 5 pct Ag, 0.3 pct Be alloy, and 129,000 psi for a 30 pct Ag, 0.5 pct Be alloy. Here it would he expected that much of the strain hardening came from the silver content of the alloys. The copper-rich side of the Cu-Ag diagram, according to Stockdale,4 is shown in the upper part of Fig 2. The electrical conductivities for copper-silver alloys annealed at 750 and 350°C, taken from the work of Johansson and Linde,5 are shown in the lower part of Fig 2. The sloping line corresponds to the conductivity of solid solutions of silver in copper, and the horizontal offshoots correspond to the conductivity of the two-phase alloys in equilibrium at the two temperatures shown. The electrical conductivities are very high, even for the 750°C anneal. The potentiality for age hardening from supersaturated alpha copper solutions appears to be excellent from the solubility line, but Smith and Lindlief6 have shown that the response to age hardening of solution-annealed alpha alloys is not good. They found that the tensile strength of a 5 pct Ag alloy aged at various temperatures was not as great as in the quenched condition, even though, anomalously, the hardness increased from RB68 to RB78 by annealing for 4 hr at 400°C after a 750°C quench. Weist7 also found that the alloys increased in hardness

Jan 1, 1948

By Glen R. Neighbors, Sylvan Cromer

HIGH subsurface temperatures and pressures are making cementing operations more difficult as deeper producing horizons are being sought. Recorded bottom-hole temperatures above 200°F. and pressures in excess of 12,000 Ib. per sq. in., obtained by combining hydrostatic and pump pressures, are not uncommon. Insufficient time is available for proper placement of standard Portland cement, because of the shortened setting time produced by these excessive temperatures and pressures, therefore special types of cements have been developed to overcome these difficulties. From the standpoint of placement, the ideal slurry would be one that would remain fluid long enough to be placed, then harden rapidly, so that there would be a limited amount of contamination and the well could be placed on production in a minimum of time. It is highly desirable, therefore, that some method be devised to measure accurately the time that any slurry will remain in a fluid state while being pumped into the well. To study the effect of elevated temperature and pressure on fluidity, the authors have developed the pressure-type consistometer (Figs. I and 2) described below, and are presenting data obtained with it, using slurries of both quick-setting and slow-setting cements. Studies were made over a temperature range from 110° to 270°F., and a pressure range from atmospheric to 3000 lb. per sq. inch. APPARATUS The fluidity of cement slurries at atmospheric pressure is usually determined with the Halliburton consistometer1 or the Thickening Time Tester.2 These instruments are similar, in many respects, to an ordinary ice-cream freezer. The slurry to be tested is placed in a container that is rotated at a constant speed with an electric motor. Constant temperature is maintained by surrounding the container with a thermostatically controlled bath. The torque on the paddles, which is proportional to the force needed to shear the slurry, is indicated on a scale. The Halliburton instrument is calibrated from 0 to 100 poises against fluids of known viscosity. To permit direct correlation of observed elevated pressure data with those published at atmospheric pressure, the authors' designs of the slurry container, paddle, and torque indicator closely resemble those used on the Halliburton instrument. Duplicate results may be obtained at atmospheric pressure in either instrument. Instead of the atmospheric constant-temperature bath, one was built from a high-pressure steel bull plug. A Uni-Bolt union equipped with a blanking plug serves as the top, permiting the instrument to be opened or closed in less than one minute. The slurry container is built from Shelby steel tubing. A wrench socket welded to the bottom of the container engages a hexagonal nut on the top of the steel shaft that rotates it. This acts as a universal

Jan 1, 1941

By J. W. Wolfe

The Benedict-Webb-Rmbin equation of state was used in digital computer programs to make rapid determinations of natural gas equilibrium phase compositions. Mixture components were the nine hydrocarbons, methane through heptane. Comparative tests were made with data from field separators, plant exchangers and literature sources. For most tests made, the B-W-R equations predrcted component K-vallles, mixture enthalpies and phase aensities within tile accuracy of available correlations for rune-component mixtures: significant deviations were noted when mixtures contained components heavier than heptune. INTRODUCTION Rapid, accurate methods for calculating the properties of hydrocarbon mixtures are needed for predicting the behavior of natural gas processes. For example, because of the common use of two-phase separation methods in gas proccssing, calculations must be made for the density and composition of equilibrium vapor and liquid phases. In addition, predictions must often be made for the temperature and pressure changes associated with the flow of single- and two-phase natural gas fluids through heat exchangers, chokes and turbines. The complex nature of non-ideal mixtures makes rigorous calculations for these natural gas properties difficult and time-consuming. Natural gas properties have conventionally been determined with generalized data correlations. These correlations, such as the K-values presented in the NGAA Equilibrium Ratio Data Book, are usually based on some average property of the mixture and have proven to give satisfactory estimates for the properties of most oil and gas systems. Digital computers, however, have not only increased the utility of these correlations, but also have made practical the use of equations of state for calculating the properties of natural gases. Potentially, if basic pure component data are available, all the desired thermodynamic properties of mixtures can be derived from a single equation of state describing the mixture. Currently. the best equation of state for describing the behavior of pure, light hydrocarbons over single-and two-phase regions, both below and above critical pressure, is that of Benedict. Webb and Rubin.' The equation contains eight constants which are determined by empirically fitting the equation to pure-component PVT data. Benedict and his co-workers presented the clevelopment of their equation as early as 1940.2 The B-W-R equation is a modification of the Beattie-Bridgeman equation of state and gives better PVT predictions than the Beattie equation at densities above the critical density. Benedict et al. made the equation applicable to mixtures by relating the mixture constants to composition and the constants for pure compounds. These authors, in a serics of articles in 1951,' showed the accuracy of the B-W-R equation when applied to light hydrocarbons and their simple mixtures, and demonstrated the equation's utility for making vapor-liquid equilibria calculations. Since its inception, the B-W-R equation has been the subject of many papers. Numerous additions and modifications have been proposed,'-',"'-':' the purpose of most being to improve the equation's ability to predict PVT properties of specific mixture systems. In 1959, Opfell, Pings and Sage summarized much of the work on the B-W-R equation in their book on equations of state." Since natural gases are primarily mixtures of light hydrocarbons, the B-W-R equation is a natural choice for an equation of state to compute both phase equilibria and thermodynamic properties of natural gases. Consequent-

Jan 1, 1967

By W. E. Foreman, James A. Redding

INTRODUCTION Screening is a mechanical process that separates particles by size. Modern coal preparation is made possible by efficient sizing. Sizing of coal is defined in terms of the opening through which an individual particle will or will not pass, or as two openings, the larger of which passes the particle and the smaller of which retains the particle. Screening accomplishes sizing by passing coal of a wide range of sizes through a series of screens, each of a decreasing size. The individual screen discharges are then directed into different screen products for subsequent sale or processing. Screening in modern preparation plants is done for the following reasons: 1 ) Removal of fine coal before a size reduction step. 2) Size separation of the coal into a coarse and fine fraction for sized products or processing in coarse and fine coal circuits. 3) Recovery of heavy media from heavy media coal cleaning circuits. 4) Dewatering. 5) Rock and trash removal by handpicking on a screen. Fig. 8-1 is a generalized flowsheet of a plant showing the use of screens in the coal preparation process. Table 8-1 shows the vibrating screen equipment utilized in Fig. 8-1

Jan 1, 1979

By D. J. McAdam, R. W. Mebs

THE technical cohesive strength of a metal means, not the interatomic forces, but the technically estimated resistance to fracture. An example of such resistance to fracture is the so-called "true" breaking stress of a tension-test specimen, the breaking load divided by the sectional area at fracture, According to the prevalent view,8 the technical cohesive strength of a metal, in any particular state as regards prior mechanical treatment and heat-treatment, is determined by a limiting value of the algebraically greatest principal stress.? In two previous papers by one of the authors,14,15 evidence was presented to indicate that the technical cohesive strength of a metal cannot be represented by a single stress value, but that it comprises an infinite number of values corresponding to the infinite number of possible combinations of the principal stresses. The technical cohesive strength thus comprises an infinite number of technical cohesion limits, each representing a specific stress combination at fracture. In the same papers, evidence was presented that plastic extension causes a continuous increase in the technical cohesive strength. Such a variation is not in accordance with the prevalent view that plastic extension first increases, then decreases, the technical cohesive strength.8 In this paper, as in the previous papers,14,15 the algebraically greatest principal stress will be designated S1, the least principal stress will be designated S3, and the intermediate principal stress will be designated S2. The technical cohesion limit under polarsymmetric tension (S1 = S2 = S3) will be termed the "disruptive stress," and the cohesion limit under unidirectional tension (S2 and S3 = o) will be termed the "severing stress." 14,15 The yield strength of a metal, according to the generally accepted theory, may be represented by a constant value of the shearing-strain energy, and hence by a constant value of the sum of the squares of the three principal stress differences. In the second of the previous papers,"' however, evidence was presented that the limiting yield stress decreases with increase in the volume stress, the algebraic average of the three principal stresses.* This influence of the volume stress becomes prominent only in the field of triaxial tension. In the two previous papers, 14,15 diagrams were presented to show the variation of the technical cohesion limit, yield stress, and ultimate stress with the combination of principal stresses and with plastic extension. Those diagrams and the resultant conclusions are derived from experimental data obtained by other investigators. They are based chiefly on results of tension tests

Jan 1, 1943

By Donald A. Brobst

The minerals barite (BaSO4 barium sulfate) and witherite (BaCO3 barium carbonate) are the chief commercial sources of the element barium and its compounds whose many uses are nearly hidden among the technical complexities of modern industrial processes and products. Barite, the major ore mineral, is extremely vital to the petroleum industry which in 1973 consumed at least 80% of the world's produc¬tion of 4.4 million tons as a major ingredient of the heavy fluid, called mud, that is circulated in rotary drilling of oil and gas wells. The re¬maining 20% of the barite production was consumed chiefly in the manufacture of barium chemicals and glass and as a pigment, filler, and extender. Barite occurs throughout much of the world and is available from three major geologic types of deposits-vein and cavity fill¬ing, residual, and bedded-in sufficient quantity at competitive prices to meet current demands. The world's demand for barite is expected to increase, and geologic circumstances are favor¬able for the discovery of new deposits of com¬mercial value. Witherite is much less common and abun¬dant than barite, although it is more desirable in many ways as a raw material for the pro¬duction of barium chemicals. The United States has not produced witherite since about 1950; England is currently the chief producer of witherite. End Uses Most of the world's barite production since 1926 has been used as a weighting agent for the muds circulated in rotary drilling of oil and gas wells. The muds fundamentally are mixtures of water, clay, and barite in different proportions that vary according to local reservoir condi¬tions. Muds with a specific gravity as great as 2.5 are used. The mud is pumped down the hollow drill stem, passes through the bit at the bottom of the hole, and rises to the surface in the space between the drill stem and the wall of the hole. In the course of this circulation the drill bit is cooled, cuttings are removed, the drill stem is lubricated, the walls of the hole are sealed, and the hydrostatic head of the column of weighted fluid helps to confine high oil and gas pressures. The latter feature aids in prevention of gushers, thus reducing both environmental pollution and waste of oil and gas resources as well as conserving the natural reservoir pressure for greater production and rate of recovery of the products contained in the rocks. Barite is particularly well suited for drilling mud because it is clean, easy to handle, soft (nonabrasive), heavy, virtually inert chemi¬cally, and relatively inexpensive compared to many other available heavy materials. Barite is used in the manufacture of glass in continuous tanks. The addition of barite ho¬mogenizes the melt and gives greater brilliance and clarity to the finished glass. Ground barite, both unbleached and bleached by sulfuric acid, is a common industrial filler, extender, and weighting agent. The rubber in¬dustry is a major consumer of barite as a filler. Barite also is added to bristolboard, heavy printing paper, playing cards, rope finishes, brake linings, clutch facings, plastics, and li¬noleum, to name but a few uses. Bleached barite has long been an extender in white lead paint because of its weight. The low index of refraction of barite, however, makes its ability to cover marks poorer than some other sub¬stances, but its low capacity for absorption of oil is a good feature. Off-color or unbleached barite can be used as a filler in colored paints. In the construction industry, some lump barite is used in concrete aggregate to weight down pipelines buried in marshy areas and to shield nuclear reactors. Because barite absorbs gamma radiation well, its use reduces the amount of expensive lead shielding otherwise

Jan 1, 1975

By Harold L. Hinds

The Homestake Ledge or Lead was discovered by Fred and Moses Manuel on April 9, 1876. They recovered a small amount of gold from the quartz outcrop, but, unfortunately, they were prospectors not hardrock miners. Their claim was sold to a group of experienced California mining men in 1877. These mining men incorporated their holdings as the Homestake Mining Company. This was the beginning of one of the greater gold mining enterprises of the Western World. Metallurgical operations progressed over the years from an eighty- stamp grinding circuit using amalgamation for recovery to the more complex circuit of today. The Homestake Mine, today, is an underground mine with the deepest winze reaching the 8,000-foot level. The ore is hoisted to the surface by two primary shafts, the Ross Shaft and the Yates Shaft. See Figures 1 and 2. It is crushed in three-stage crushing plants located in the headframes. From here, it is trammed to the mill fine- ore bins by electric locomotives. The Lead grinding plant milling circuit, known as the South Mill, receives ore from the crushing plant at minus 112 inch (Figure 3). This material is dumped into overhead fine-ore bins from five- ton rail cars. The fine-ore bins have a live capacity of about 3,700 tons. The South Mill bins can also be fed by a conveyor system which reclaims ore from an 80,000-ton capacity stockpile. This stockpile is built up from peak mining production periods and available surface low grade material. It is then reclaimed during low mine production periods. The grinding circuit at the South Mill consists of four rod mills in open circuit followed by four ball mills in closed circuit. Three of the rod mills are 6-foot by 12-foot Marcy's. The other is

Jan 1, 1983

By H. I. Aaronson

The nucleation of pearlite at proeutectoid ferrite is inhibited, to an increasing extent, at the following locations: At twin boundary-nucleated ferrite, between closely spaced ferrite sideplates, and at intragranular plates. These effects are discussed in terms of the influence of transformation strain energies and of the interfacial free energy of austen-ite:ferrite boundaries on the rate of pearlite nucleation. The growth of pearlite into the interiors of austenite grains from the region of the grain boundaries is markedly restricted when low reaction temperatures and large austenite grain sizes permit the development of interlocking networks of intragranular ferrite plates. PREVIOUS investigators have made extensive studies of the interactions which occur between the proeutectoid ferrite and the pearlite reactions from the viewpoint of the mechanisms through which pearlite interferes with the nucleation and growth of proeutectoid ferrite.1-3 In the present investigation, the processes through which proeutectoid ferrite (hereafter termed simply "ferrite") can reduce the rate of formation of pearlite have been explored in some detail. A steel with a relatively low carbon content, in which the ferrite reaction can compete successfully with the pearlite reaction over a wide range of reaction temperature, and exceptionally coarse-grained specimens, which further emphasize the role of the ferrite reaction, have been employed for most of this work. A brief examination also has been made, however, of the effects of smaller austenite grain sizes upon these processes. Experimental Procedure The steel employed had the following composition: 0.29 pet C, 0.76 pet Mn, 0.25 pet si, 0,007 pet S, and 0.005 pct P. This alloy was homogenized for 48 hr at 1250°C. The investigation was performed

Jan 1, 1959

By G. B. Gould

FROM the very inception of the price-control experiment in the bituminous-coal industry, the problem of price differentials was of major importance. In fact, assuming that there will be no legal or Govern- mental obstacles to price control, the successful maintenance of the present or any other method designed to control bituminous-coal prices will depend upon the discovery of some satisfactory way to determine these differentials in price, among: individual mines and groups of mines. Being of organic origin, bituminous coal is a commodity that presents an almost infinite variety of qualities. It is inevitable, therefore, that a work- able price-control system must attempt

Jan 1, 1935

By Alexander Sattman, Anton Homatsch

Jan 1, 1894

By C. D. King

The key to maximum production of ingots for the war effort is maximum production of pig iron. For any given furnace and ore, the most important single influence on blast-furnace production is the quality of the furnace coke. It is generally recognized that undoubtedly deterioration of Pittsburgh coking coals will be accelerated by the depletion of some of the better grades of coal; the extension of mine mechanization, with attendant degradation of coal quality; and the opening of new coal fields, some of which are known to be fairly high in sulphur. All of these factors, contributing as they do to higher ash and sulphur, and not infrequently to inferior quality of coke, made it desirable that an extensive study be undertaken to determine the effect of washing some coals that closely approximate the average chemical composition of coking coals to be expected in the future by the subsidiaries of the United States Steel Corporation in the Pittsburgh district. It was deemed advisable to study the improvement obtained by washing such coals and to determine the need for supplementing the existing coal washery at Clairton to assure continued maximum production of pig iron from presently available furnace stacks. The existence of the coal washer at Clairton made it possible to conduct tests on coals used in raw form and on similar coals after washing. This study covers an investigation of the quality of furnace coke as affected by washing coking coals, and is confined to the use of 100 per cent high-volatile Pittsburgh seam coals from Fayette and Greene Counties in the manufacture of furnace coke. It covers the improvement in chemical and physical properties as well as the degree of uniformity in coke obtained by washing these coals, and includes the effect on blast-furnace production and practice. The test period involved is four months; the plants, Clairton by-product coke plant, and the Carrie No. 1 and No. 2 blast furnaces at Rankin, Pa., Carnegie-Illinois Steel Corporation. Clairton By-product Coke Plant and Coal Washer The Clairton by-product coke plant carbonizes 30,800 net tons of coal daily in 22 batteries containing 1482 ovens. Three oven sizes are used, commonly known as wide, medium, and narrow types, recognizing the difference in oven width, These ovens also differ in height and length. The present coal washer has a daily capacity of approximately 14,000 tons, leaving 16,800 tans to be carbonized in raw form. Washed coal is used on all the narrow ovens and on three of the six batteries with ovens of medium width, raw coals being used on all the remaining ovens. The customary arrangement is

Jan 1, 1944

By C. D. King

The key to maximum production of ingots for the war effort is maximum production of pig iron. For any given furnace and ore, the most important single influence on blast-furnace production is the quality of the furnace coke. It is generally recognized that undoubtedly deterioration of Pittsburgh coking coals will be accelerated by the depletion of some of the better grades of coal; the extension of mine mechanization, with attendant degradation of coal quality; and the opening of new coal fields, some of which are known to be fairly high in sulphur. All of these factors, contributing as they do to higher ash and sulphur, and not infrequently to inferior quality of coke, made it desirable that an extensive study be undertaken to determine the effect of washing some coals that closely approximate the average chemical composition of coking coals to be expected in the future by the subsidiaries of the United States Steel Corporation in the Pittsburgh district. It was deemed advisable to study the improvement obtained by washing such coals and to determine the need for supplementing the existing coal washery at Clairton to assure continued maximum production of pig iron from presently available furnace stacks. The existence of the coal washer at Clairton made it possible to conduct tests on coals used in raw form and on similar coals after washing. This study covers an investigation of the quality of furnace coke as affected by washing coking coals, and is confined to the use of 100 per cent high-volatile Pittsburgh seam coals from Fayette and Greene Counties in the manufacture of furnace coke. It covers the improvement in chemical and physical properties as well as the degree of uniformity in coke obtained by washing these coals, and includes the effect on blast-furnace production and practice. The test period involved is four months; the plants, Clairton by-product coke plant, and the Carrie No. 1 and No. 2 blast furnaces at Rankin, Pa., Carnegie-Illinois Steel Corporation. Clairton By-product Coke Plant and Coal Washer The Clairton by-product coke plant carbonizes 30,800 net tons of coal daily in 22 batteries containing 1482 ovens. Three oven sizes are used, commonly known as wide, medium, and narrow types, recognizing the difference in oven width, These ovens also differ in height and length. The present coal washer has a daily capacity of approximately 14,000 tons, leaving 16,800 tans to be carbonized in raw form. Washed coal is used on all the narrow ovens and on three of the six batteries with ovens of medium width, raw coals being used on all the remaining ovens. The customary arrangement is

Jan 1, 1944

By I. J. Lin, A. Mitzmager

This paper describes a series of experiments conducted to determine how the physicochemical properties of the suspending fluid affect the size reduction of quartz in a ball mill. Particular attention was directed toward the differences in rate of grinding and particle size distributions when either polar or non-polar fluids were the suspending liquids. Grinding was performed with water, carbon tetrachloride and methylcyclohexane as the liquids, and also in nitrogen for comparative purposes. From the results ob- tained, the authors have concluded that the presence of water greatly enhances efficiency in the grinding of quartz. Comminution is generally regarded as a purely physical process in which fragmentation of a solid is obtained by the application of suitable forces. In 1944, however, Rehbinder et al.1 pioneered the idea that the interfacial forces between the solid and the media plays an important role in comminution. Since then, a number of researches have shown conclusively that comminution is affected by surface chemical phenomena,2-5 and Gaudin went as far as to compare comminution to a chemical reaction.6 The effect of the viscosity and the density of the fluid media in grinding was also investigated, but

Jan 1, 1969

By A. C. Dittrick

THE Simon-Carves washer, originally known as the Baum jig washer, was first built in Europe about 1892. It was probably the first washer to use intermittent pressure of air on water in one part of the wash box to obtain water pulsations in another part. This type of washer was also the first to successfully clean various sizes in the same unit. Previous practice was to size closely before washing. Today there are several large firms abroad, and a few in the United States, that are constructing the Baum type washer. The design of all is practically the same, their differences being only in details. In 1928, the Hanna Coal Co. first gave consideration to the question of coal cleaning. It was believed at that time that by efficient removal of so-called noncombustibles appearing in the Pittsburgh No. 8 seam, certain markets that had been lost due to poor preparation might be recovered. Mechanical cleaning and mechanical loading were under consideration. This type of cleaning was considered the most practical means of removing impurities in the sizes below 4 in. It was decided to adopt mechanical cleaning and develop a system of mechanical loading that would be successful on No. 8 coal.

Jan 1, 1935

By Ernest Burchard

FLUORSPAR is found in most of the states from the Rocky Mountains westward, and commercial production of the mineral has been reported from Arizona, Colorado, Nevada, New Mexico, Utah and Washington. The map in Fig. 1 indicates the general distribution of many of these deposits but it is by no means complete. In the summer of 1926 the writer examined certain deposits of fluor-spar in Arizona, California, Colorado, New Mexico and Washington; in November, 1927, revisited the Jamestown, Colo., district, and in earlier years examined deposits in Colorado and New Mexico. Based on notes of his own and. on descriptions and other data by H. A. Aurand, H. W. Davis, R. B. Ladoo, V. C. Heikes, W. D. Johnston, Jr., and by producers of fluorspar, he prepared the following brief descriptions of deposits and estimates of reserves of fluorspar, originally for the use of the subcommittee on fluorspar of the Joint Committee on Foreign and Domestic Mining Policy and on Industrial Preparedness respectively of the Mining and Metallurgical Society of America and the American Institute of Mining and Metallurgical Engineers. Descriptions of many fluorspar deposits in various western states and districts have been published. It is not feasible to summarize this literature here, but the appended bibliography will indicate to the interested reader what papers are available.

Jan 1, 1933

By Carl A. Zapffe, George A. Moore

IN a previous publication from this laboratory1 the conclusion was drawn that the embrittling effect of occluded hydrogen on iron and steel must result from the precipitation of the gas within small openings through the crystal structure. A review of the literature then published indicated the real existence of crystal sub- structures of the mosaic type and gave presumptive evidence that the "rift openings" associated with hydrogen occlusion are the same as the "disjunctions" of the mosaic theory. Inasmuch as no clear conception of the actual nature of the crystal fragments and openings inherent in these theories has been established, it was considered desirable to obtain direct micrographic evidence of their true configuration. In this direction the standard methods of metallographic attack have proved useless. Recourse was had, therefore, to the direct examination of the surfaces upon which failure by cleavage had resulted from the presence of hydrogen. It was expected that such a surface, un- affected by chemical attack and undistorted by polishing, would reveal the fine openings penetrated by the gas and thus indicate the real nature of the substructures. MATERIALS STUDIED In commercial steels, defects caused by hydrogen take various external forms ac- cording to such factors as structure and purity, and to the extent to which hydrogen either occludes or produces chemical changes. The present work relates only to the well-known transcrystalline hydrogen embrittlement-"pickling brittleness"-in which elemental hydrogen occluded within the grain develops cleavage characteristics. For example, hydrogen embrittlement resulting from hydrogen reaction products is excluded from detailed study. It was also desirable, as far as possible, to have the study uncomplicated by other elements which themselves cause brittleness. Three types of iron were used. These included ingot iron, decarburized free- machining steel, and a specially prepared, aluminum-killed, electrolytic iron. This , choice allowed a comprehensive selection of unavoidable minor impurities and inclusions, which could subsequently be shown to have no specific effects on the structures within the grains. Carbon, and any other impurities free to react with hydrogen, were first removed by a preliminary annealing treatment in hydrogen. Subsequent treatment in vacuo extracted much of this hydrogen and its gaseous reaction products. The resultant ductile iron was then embrittled either by a second anneal in hydrogen, followed by rapid cooling, or by cathodic electrolysis. Group I: Prepared from Armco Ingot Iron As shown in Table I, the principal impurity in this iron was oxygen, which survived the purifying treatment to a large extent. Two series were prepared. The first (Nos. SIO-24) was purified only one day in hydrogen and dehydrogenized one day in nitrogen. Containing both hydrogen and its

Jan 1, 1943

By G. S. Rice

Some form of longwall mining is generally used in Continental Europe; also in Great Britain where the coal is weak and friable, or the coal bed provides material for pack walls and filling, or where the bottom is soft and squeezes up easily, or the roof is pliable, or the bed is thin and brushing provides building material, or the thick multiple seams are mined in layers, such as the 24-ft.seam at Weymss, Scotland, or the 10-yd. pitching bed near Coventry, England. Pillar methods have been retained in British fields where the coal beds are from 5 to 9 ft. (1.5 to 2.7 m.) thick, and free from thick partings or binders or without draw slate, which would provide waste rock for pack walls, or where the roof is hard and requires shooting to bring down, and also the bottom or floor is comparatively hard. The room-and-pillar system, by which probably 95 per cent. of the coal of the United States is produced, is now found in only a few mines in Wales, where it is known as the pillar and (single) stall method. The American room-and-pillar system is not equivalent to the bord-and-pillar or stoop-and-room system. The essential difference between the bord-and-pillar and the average American room-and-pillar system is probably due to natural conditions. The majority of the coal mines in the United States have a depth of less than 700 ft. (213 m.). The bulk of the coal mined in Europe comes from a depth of more than 1200 ft., while the deepest mines in Great Britain, Belgium, and France reach 3500 to 4000 ft. In deep workings wide spans are impracticable, even with the use of abundant timber; accordingly, as the mines in the United States become deeper the rooms will become narrower and the pillars thicker, and the bulk of the coal will be extracted on the retreat. It is generally conceded, without reference to the cost of production, that the larger the pillars left on the first mining, the more thoroughly can the coal be extracted. In Europe complete extraction is generally compelled either by the lessors or by the governments; whereas in this country it has been more largely a question of competitive cost of production, or the support of the surface in the flat farming districts of the

Jan 1, 1922

By Oliver Bowles

Two striking events marked the year 1871-the establishment of the A.I.M.E. and the beginning of the portland cement industry, the most spectacular of all the nonmetallics in its development. Just as David Saylor's first portland cement, made in a little mill at Allentown, Pa., in that year was the forerunner of a mighty industry, the products of which in 1942 were made in 155 plants scattered throughout the country (having attained a value of nearly $300,000,000), so the Institute from its small beginning has attained a membership of many thousands, likewise decentralized into a series of individual sections of wide geographical distribution. Concurrent with the establishment of the Institute was also the invention of the steam drill, followed by the compressed-air drill about 1904. These mechanical drills were so immeasurably in advance of the hand drill and hammer used previously that quarrying and mining of present-day magnitude could never have been attained without them. Some outstanding occurrences have marked this eventful three quarters of a century. The concrete age, with its enormous demands for cement, aggregates and steel, is of primary importance. Of interest also is the shift of fertilizers from the organic to the mineral field. Nitrates, primarily obtained

Jan 1, 1947

By F. R. Hensel

THE demand for clean steel is increasing daily. New processes of refining steel are being developed in order to remove all nonmetallic inclusions as completely as possible, as it is the general opinion that. inclusions affect the dynamic properties of steel and iron to such an extent as to justify great expense for their removal. It is surprising to note at the same time the commercial development of a new process for making artificial wrought iron. By this process slag and steel are thoroughly mixed, the amount of nonmetallic inclusions usually exceeding 2 per cent in weight. The contradiction in these two efforts is obvious and is responsible for the investigation reported in this paper. H. W. Gillett also has recently emphasized the need for further research on wrought iron.1

Jan 1, 1932

By Alvinus Brown Wood

THE ancient copper-mines of Lake Superior, having been destroyed or covered by-modern mining-dumps, are not accessible to the present inhabitants of that region, and, since no more are likely to be found, some account of those already discovered, from one who has seen them, may be acceptable to the Institute. Early in May, 1855, 1 took a party of men to open an ancient pit on the Quincy mine-location. Mr. C. C. Douglas was the Agent.," as mine-managers were then called on Lake Superior. The Quincy Co. had previously done work on a fissure-vein, several hundred feet west of the Amygdaloid lode (afterwards called the Pewabic lode), on which was the ancient pit herein described. It was at this pit that the Quincy' main shaft was subsequently stink. The ancient pit showed an apparent depth of about 4 ft., but when cleaned out it was shown to be 14 ft. deep, having been filled up by the sliding-in of material composed largely of broken rock, taken out in sinking the ancient shaft, and left near its mouth. Midway of the shaft, and below water-level, was found a scaffolding, of white-birch poles,- which had been used as a landing, to assist in removing the excavated rock. The shaft was 7 ft. in diameter. The excavation had been done by first building fires in order to disintegrate the rock, as was proved by the abundance of charcoal found; then breaking the softened rock with hammers of diorite, such as is found in the greenstone range on Keweenaw point. These hammers had about. the size of large paving-stones. Only broken ones were found, the whole ones having been doubtless carried away for other work, such as could be traced on the lode for a hundred feet or more to the south. At the place where this shaft was stink, barrel-copper (i.e.,

Mar 1, 1906