Search Documents

By C. K. Leith

AT the outset I would like to make it clear that I do not enter this discussion in a controversial spirit, but in an attempt to contribute something helpful to an understanding of a difficult problem. I have too high regard for the sterling quality of the work of the men who have studied this subject in detail to offer anything in the way of essential contradiction to their statements of fact. Difference of opinion arises from differing valuation of the possible alternative hypothesis which these facts suggest. Some degree of recrystallization in limestone contact zones has been recognized by many investigators. Earlier investigators, for the most part, assigned an important, if not the most important, role to recrystallization in development of these zones. With the growing recognition, of introduction of ores and gangue materials into the contact zone from igneous rocks through the medium of primary magmatic solutions, there has been a tendency to ascribe to this process most, if not all, of the chemical and mineralogical characteristics of the contact zone. This has involved a correspondingly diminished emphasis on recrystallization of substances already there as a factor in the process, and in some cases even the complete elimination of this hypothesis. From detailed study of a few contacts, casual observation of others, and a general familiarity with the literature, some of us have been led in recent years to raise the question whether the pendulum has not swung too far away from recrystallization toward direct introduction from igneous sources, and to argue for more recognition of the part played by recrystallization.1 The inevitable sequence has been that those of us who have taken this view have been charged, at least by inference, with emphasizing recrys-tallization to, the total exclusion of the alternative process. Scientists, like other men, like to classify and pigeon-hole views under simple and definite designations, leaving out qualifications which would tend to make the classification more difficult to state. This has made the problem seem more definite and simple, but has tended to obscure the fact that the disagreement is primarily not one relating to essential facts, but one of

Jan 6, 1914

By John H. Holloman

In recent papers, O'Neill,' Vivian, and Zener and Hollomon3 have reviewed some of the information concerning the relations between stress and strain during plastic deformation. Since further information has been obtained since these reviews were published, this paper attempts to further coordinate and amplify the knowledge concerning the plastic deformation of metals in simple tension. Ordinarily the results of tensile tests of metals are presented as graphs in which the load divided by the original area is plotted as a function of the percentage of elongation measured over some specified gauge length. The interpretation of graphs of this sort is limited, since the stress required to deform the metal at any stage of the deformation is actually the load divided by the instantaneous rather than the original area. Furthermore, each increment of the deformation is performed on metal that has been previously deformed, and, as pointed out by Ludwik,4 the strain could be more effectively defined: where e is the strain and AO and A are, respectively, the original and instantaneous areas. The results of the tensile tests can be more effectively presented and interpreted if the stress* (load divided by actual area) is .lotted as a function of the strain as defined above. A schematic curve of this type is presented as Fig. I. In a previous paper,6 the concept of Ludwik7 concerning the flow and fracture of metals was successfully employed to explain some of the puzzling results of notched-bar impact tests of steel. It appears that the use of this concept ii; very fruitful and should be kept in mind in any study of the deformation charactcristics of metals. Ludwik considered that a flow stress-strain curve of a metal was essentially a locus of points that described the stress required for plastic flow of an infinite numbcr of specimens, each with a different strain history determined by the preceding part of the flow curve Each of these specimens can also be considered to have a fracture strength. Uniortunately (or fortunately depending upon the point of view), all the specimens, except the one deformed to the fracture strain, flow and do not fracture. Even though the metals do not fracture, the concept of a fracture-strength curve seems

Jan 1, 1945

By Carl Altstetter, Roy Adams

Measurements of enthalpy changes and transformation temperatures me reported for the fcc -hcp marten-sitic transformation in pure cobalt single and multi-variant crystals andpolycrystalline specimens. From these measurements the free-energy difference between the two phases was calculated for both heating and cooling and for repeated cycles through the transformation. For heating of single crystals the average value of enthalpy change was 113 cal per mole but on cooling it was 84 cal per mole. This difference is interpreted in terms of lattice imperfections which are introduced during transformation. A calorimeter suitable for measurement of enthalpy changes of athertnal transformations is described. COBALT exhibits an allotropic phase transformation at around 417°C' where an hcp phase (a = 2.507, c = 4.0686, c/a = 1.6228)~ stable at low temperatures transforms to an fcc phase stable up to 1495°C. The transformation has a hysteresis of about 30°C— the exact magnitude of the hysteresis depending on the number of transformation cycles, grain size, impurity content, and prior treatment.'-6 The athermal character of the transformation and surface relief due to transformation shear indicate that the transformation is martensitic. Pole mechanisms for the transformation have been discussed by Sebilleau and Bibrin, Bilby, Seeger,' and Basinski and Christian. These authors have proposed that the cooling transformation is effected by rotation of a Shockley partial dislocation around a pole dislocation with a screw component of 2a/3(111). Such a rotation would change the stacking of close-packed planes from the abcabc fcc stacking to the ababab hcp stacking sequence. This mechanism would predict a lattice correspondence of {111}fcc~~(0002~cp, have been observed. One would expect the heating transformation to occur similarly, involving dislocation movements on the (0002)hcp. However, a high density of pole dislocations and high dislocation ve- locity are required to account for microscopic observations. Furthermore, the high back stress developed on the Shockley partial dislocation as it rotates toward the sessile dislocation associated with it makes it doubtful that this is in fact the transformation mechanism. A mechanism for spontaneous nucleation of partial dislocations1*l2 seems more reasonable. If a single crystal of cobalt is cycled through the transformation but never heated above 600°C, it will remain single."13 However, if the specimen is heated through the transformation and held for a short time at or above 1000°C before cooling, the cooling transformation usually involves all four {lll}fcc habits, resulting in neighboring orientations of hcp differing by 70.5 deg. This condition is termed multivariance and has been observed by Bibring and sebilleau5 and Nelson and ~ltstetter.' The latter authors used single crystals of cobalt grown in an electron beam zone refiner. They proposed that the strongly directional cooling caused the initial cooling transformation to occur on the {lll)fcc most nearly perpendicular to the temperature gradient. Transformation shear on one set of {lll}fcc planes immobilized dislocations on the other {lll}fcc planes involved in the initial transformation. Since there is only one (0002)hcp plane orientation, the product of subsequent heating transformations could have no more than two variants—the original fcc orientation or its twin. If, however, the specimen was annealed at a high temperature, such as 1000°C, there would be relaxation of dislocations into low-energy configurations, and in the absence of a sharp temperature gradient transformation on all four (111 Ifcc planes could occur. If a dislocation mechanism is responsible for the transformation, the perfection of the lattice should affect the reversibility of the transformation. Mutual constraints of neighboring grains in polycrystalline material would inhibit dislocation movement resulting in increasingly sluggish transformation. Indeed, Nelson and Altstetter found the M, to decrease and the A, to increase in going from single crystals to multi-variant specimens to polycrystals. The effect is enhanced by decreasing the grain size of a solid specimen or a powder.6'14 Data on the free-energy difference necessary to initiate the transformation gives information about the driving force of the transformation. This is an important consideration in the understanding of the transformation mechanism. The free-energy change associated with the transformation of the hcp phase to the fcc phase at some temperature T different from the equi-

Jan 1, 1969

By C. A. Stetefeldt

In my paper on "The Refining of Sulphides Obtained in the Lixiviation-Process with Hyposulphite Solutions," read at Cleveland, June, 1891 (Trans., xx., 37), I recommended the Roessler converter

Jan 1, 1893

ALTHOUGH the refining period of the heat is generally defined A as starting after the charge has been completely melted, it may more properly be considered as beginning with the first efforts to facilitate the shaping up of the slag and the making of corrective additions for the control of slag or metal composition. Such actions may be initiated during the latter half of the lime boil. The early part of the refining period may, then, in essence overlap the latter part of the melting period. The primary aims of the refining period are: (1) to reduce phosphorus and sulfur from the steel bath to levels safely below the maximum contents specified; (2) to eliminate carbon to a specified level as rapidly as possible and still allow time for proper conditioning of the slag and attainment of the necessary bath temperature; and (3) to have the heat ready for tapping or furnace deoxidation, with slag in the proper physical and chemical condition, and with carbon and oxygen contents and the temperature of the steel at the proper levels for the composition and grade of steel being produced. The particular conditions that fulfill these aims are distinctly different, depending upon whether the steel is to be finished according to fully killed semikilled, or rimming practice and also depending upon the carbon range specified. Regardless of the type of charging practice employed, the object of the refining period is to produce repeatedly the desired finishing and tapping conditions for the grade of steel being produced. The variations and proportions of raw materials used in the charge may cause some variations in the degree of control required during refining, but not in the method of control. The refining period can therefore be discussed from a viewpoint largely independent of charging and melting practice. SHAPING UP THE SLAG In the first helper's vocabulary, refining practice consists in

Jan 1, 1964

By T. MacDONALD

ATHOUGH flotation has been a commercial process for over twenty years, the last two years have witnessed a sudden and phenomenal increase in our knowledge of how to separate minerals heretofore not considered amenable to flotation at all. As remarked by Professor Locke in the January issue. "Either commercial or laboratory flotation is reported on zircon, ilmenite, carnotite, kyanite, scheelite, chromite, fluorite, feldspar, cassiterite, wolframite, barite, and clay. Attractive patents on soap flotation are U. S. Nos. 2,000,656 and 2,040.187. A survey by Ralston in the February E. & M. J. adds many other minerals to this impressive list. The simple but pregnant fact is that any mineral can be coated, directly or indirectly, with a water-repellent coating, and since this is true, it follows that any mineral can be floated. Fundamentally, this is no new discovery, where, for instance, is the mineral that cannot he washed from a pair of dirty hands by means of soap and water, given the absence of refractory greases or oils which would have no proper place in flotation ?

Jan 1, 1937

By Robert Maes, Robert de Strycker

The solidifzcation reactions in the Cu-Sn-As system were determined by microscopic examination, thermal analysis, and X-ray diffraction. The system presents no ternary compound. There is a quasi-binary section, of a simple eutectic type, between the compounds Cu5As2 and SnAs; the system presents, in addition, one ternary eutectic reaction, one ternary peritectic reaction, and seven transitional reactions. The temp-peratures corresponding to each of these reactions were determined, most of them with an accuracy of *lLC. The isothermal lines of the liquidus surface were also established for almost the entire diagram. NO reference was found in the literature relative to the Cu-Sn-As phase diagram and this is believed to be the first study on this subject. The Cu-Sn diagram was taken from Hansen and Anderko;' it is represented by Fig. 1, with the phase designation which will be used in the remainder of this work. For the Cu-As diagram, the solution proposed by Hansen and ~nderko' must be modified to take account of recent data, principally from Heyding and Despault~ and from Hume-Rothery and Burns; this yields the diagram represented by Fig. 2. As for the Sn-As diagram, it is not established with certainty, particularly so far as concerns the solid solubility of tin in arsenic and the solidification reactions near the compound SnsAsz. For this last point, Hansen and Anderko propose two solutions: congruent melting of Sn3Asz with a eutectic SnsAsZ + SnAs or incongruent melting implying a peri-tectic reaction L + SnAs = Sn3As2. Microscopic examination of the few binary alloys prepared in this composition range made us prefer the second of these solutions, which gives the diagram shown by Fig. 3. EXPERIMENTAL METHODS The experimental techniques used in this work were microscopic observation and thermal analysis; a few X-ray diffraction patterns were taken to verify the

Jan 1, 1967

By Lester C. Uren

Petroleum occurs, in nature, as a fluid saturating the pore spaces between the grains of porous rocks or aggregations of rock particles such as sand, sandstone, conglomerate, shale, limestone, etc. The oil, under the influence of gas pressure, hydrostatic pressure, gravity, earth pressure, and, perhaps, other natural forces, is caused to flow through the porous "reservoir rock1' into wells penetrating the stratum in which the oil occurs. The principal moving force is the pressure of dissolved or occluded natural gas within the oil, though this force is assisted by gravity and by the hydrostatic or buoyant pressure of ground water about the edges of the "pool." The wells, providing outlets to the surface, are centers of reduced pressure and the flow of rock fluids into a particular well is usually an expression of the difference in pressure existing between the space within the well and that of the stored oil within the reservoir rock. The greater this differential pressure, the more rapidly will oil flow from the source rock into the well. Opposing movement of the oil from the reservoir rock into the well are certain natural forces related to the rock structure, such as pore friction and capillarity, and certain others related to the physical properties of the oil, such as viscosity and adhesion. The differential pressure between the well and the boundaries of the area drained by it must be sufficient to overcome the forces opposing flow if there is to be movement of oil into the well. If by any device the resistance to movement of the oil may be reduced, the oil will flow into the well at a more rapid rate and the effective area of drainage will be increased.

Jan 1, 1925

By J. J. Kramer, W. A. Tiller, G. F. Bolling

The solidification of poly crystalline zone-refined lead has been examined. A novel casting technique was used, with several advantages such as unidirectional heat flow, atmosphere control, and decanting of the liquid during any stage of growth. The experimental results show the separate existence of two textures, a (111) surface texture at the chill surface and a texture in the columnar zone, in the absence of conditions which would produce dendritic growth. WALTON and chalmers have most recently shown that the dendrite direction is the preferred axial orientation for the solidification of many metals in casting. Experimentally, for aluminum and lead, they showed that in the columnar zone the dendrite direction, <l00>, predominated, developing from an equiaxed chill cast layer that exhibited no preferred orientation. A reasonable description of the way in which grains closer to the dendrite orientation were able to encompass other grains was then set forth. For their materials, it was also shown that high superheats could inhibit a preferred axial orientation from developing, presumably by inhibiting dendrite growth. The observations of Rosenberg and iller, on the other hand, showed that zone-refined lead, cast under conditions similar to those of Walton and halmers,&apos; had a definite <111> texture in the columnar zone. However, no examination was made of the chill surface to find out if the columnar zone texture was independent of the orientations at the surface. Since the existence of preferred growth in Upure" lead is thus in doubt, a reexamination of the casting of zone-refined lead is presented here, using a novel casting technique. EXPERIMENTAL PROCEDURES AND RESULTS Zone-refined lead was prepared from two starting materials;99.999+pct supplied by ASARCO, and 99.999pct supplied by COMINCO. The manner of zone-refining and the phenomenological tests for purity after refining, have been describedelsewhere.&apos; The casting apparatus is shown schematically in Fig. 1. The following general procedure was used: The metal was cut directly from the best parts of

Jan 1, 1963

By R. L. Rickett, S. H. Kalin, J. T. Mackenzie

Aluminum killed low carbon steel, § which is now used extensively for severe deep drawing or other difficult forming operations, is unusual in that its grain structure, after cold reduction and box annealing in accordance with conventional continuous sheet or strip mill practice, often is elongated, although at times it is equiaxed. Since this unusual structure has been found superior for many, but not all, severe forming operations, recrystallization of the steel, both at constant temperature and on continuous heating, was investigated and compared with that of rimmed steel in the hope that something might be learned about the mechanism of, and the factors controlling, the formation of such elongated grains. In this structure, the grains are elongated both in the lengthwise direction of the strip and transverse to this direction, even though nearly all of the extension in both hot and cold rolling is in the lengthwise direction. The grains are thus roughly pancake-shaped, being longer and wider than they are thick, as observed also by Burns and McCabe,1 and as illustrated by the typical structures shown in Fig 1. Fig la, representing a conventional longitudinal section, shows the length and thickness of the grains, whereas Fig Ib shows their length and width as seen by examining a section parallel to the sheet surface. Both illustrate the very irregular grain boundaries usually associated with the elongated grain shape. A finer equiaxed grain structure in this same grade is shown in Fig Ic. Either the elongated or the equiaxed structure may be present in the annealed product, and in rare instances the two types may coexist in a single specimen, as shown in Fig 1 d. Isothermal Recrystalliza-tion of Rimmed and Alamimum Killed Steel An aluminum killed steel known to have an elongated grain structure after conventional processing (Steel B, Table l), was selected for the initial recrystallization studies; for comparison, a rimmed steel, A in Table 1, was used. Samples of each in the form of hot rolled strip 0.075 and 0.095 in. thick, respectively, were cold rolled on a small laboratory mill in steps of about 0.010 in. per pass to obtain total reductions of 40 and 60 pct. Small pieces of the cold reduced strip were heated in lead at selected constant temperatures for one of several periods of time, then cooled in air. Rate of heating in the lead was, of course, very fast. Hardness of the cooled specimen was measured and a longitudinal section examined metallographically. Isothermal recrystallization curves for these two steels at 1050°F, based on hardness of the air cooled specimens, are shown in Fig 2 in which the amount of recrystallization corresponding to each plotted point is indicated. The marked difference in the behavior of these two types of steel is evident. After a corresponding amount of cold reduction, the rimmed steel recrys-tallizes in a much shorter time than the killed steel and the shape of its recrystallization curve, (plotted on a logarithmic time scale), is very different. The curve for rimmed steel indicates that recrystallization is analogous to isothermal transformation of aus-i.enite in that it proceeds at a progressively faster rate up to some 50 pct recrystallization, then at an increasingly slower rate. For the aluminum killed steel, however, the start of

Jan 1, 1950

By R. W. Raymond

(Pittsburg Meeting, March,1910.) THE Giroux Consolidated Mines Co. is equipping a five-compartment shaft at Kimberly, Nev., which will serve the Alpha mice. The depth of this shaft, January, 1910, is 963 ft., and of this depth 948 ft. was opened by raising, 15 ft. of sinking was done so that the bearers, collar-set, and three shaft-sets might be installed and concreted, and with this done it was possible to erect the necessary surface-equipment for resuming shaft-timbering on the completion of the raise. The arrangement of the shaft-timbering is shown in Fig. 1. At the 1,000-ft. level of the Alpha, and 750 ft. SW. from the Alpha shaft, a 14- by 18-ft. station was cut, and a 25-h-p. air-hoist *as installed. From here the raising commenced on July 5, 1909. The raise was cut approximately 13 by 21. ft. in area, and supported by timbering with square sets, illustrated in Fig. 2, which shows the division into four compartments. The end compartments, which were used as chutes, had the center girts heavier than in the others on account of the wear from falling rock. The chute-lining was braced by inserting 8- by 8-in. stiffeners parallel to and half way between successive caps. Similarly, the lagging on the wall sides of the cage-way and the compartment for pipes and ladder was stiffened with 4- by 6-in. timbers. In the pipe-and-ladder compartment the chute-stiffeners were reinforced with 8- by 8-in, struts, and as the cage-way was partitioned off by braced lining, there was practically no chance of rock entering the ladder-way in case a chute burst into the cage-way. Over the two center compartments the last two, sets were always bulkheaded with 8- by 12-in. timbers, shown in Fig. 3, and from the lower bulkhead the cage sheave-wheel was suspended. After a round of holes had been blasted and the loose

Jun 1, 1910

By R. I. Jaffee, J. G. Dunleavy, W. Hodge, H. R. Ogden

Early in 1946, at the instigation of the U. S. Army Signal Corps, the authors made an extensive survey of the available literature covering high-strength, high-conductivity alloys. For the purposes of the Signal Corps, the minimum tensile strength to be considered was 150,000 psi, together with at least 50 pct IACS conductivity. No single alloy was found to be in production, or mentioned in the literature, which had this combination of properties. The constitution diagram for the iron-copper alloys is not well established in the respect to the two-liquid region. Fig I, taken from the 1939 Ed. of the ASM Metals Handbook, shows a two-liquid system existing above the liquidus temperature, but disconnected from it. Although Ruer and Fickl and Ruer and Goerensz definitely established the fact that two liquid layers could occur in the system, Ruer3 was not convinced that the line of immiscibility was closed in the center. Maddocks and Claussen4 found no liquid immiscibility at temperatures up to 157oOC in alloys containing almost no carbon. Although the diagram would indicate age hardening of the copper-iron alloys is possible, Hanson and Fords found that little hardening effect could be obtained. However, Gordon and Cohen6 reported that the response is better if the quenching is very efficient. Although iron has a potent effect on the conductivity of copper, Hanson and Fords have shown that, when hot-rolled copper-iron alloys are aged at 1200°F, the electrical conductivity decreases sharply with iron contents up to 0.2 pct Fe, and then levels off at conductivities between 60 to 70 pct IACS with compositions to 2.1 pct Fe. They also found that aging did not increase the tensile strength, although increasing iron content gave a moderate improvement in strength. High-strength copper-iron alloys, usually containing about 60 pct iron, had been reported by Smith and Palmer.7 They found that an alloy containing 56.4 pct copper, 0.21 pct magnesium, balance iron, would give a maximum tensile strength of 170,000 psi and an electrical conductivity of slightly over 35 pct IACS. The alloy could also be processed to have I50,000 psi tensile strength, and about 41 pct I.\CS conductivity. Decreasing the iron content increased the electrical conductivity, but the long mushy range during freezing of the alloy containing 10 to 20 pct iron made the production of good castings difficult. In spite of the difficulty encountered by Smith and Palmer with alloys of around 20 pct iron, it was decided to make a rather complete investigation of this type of alloy. As a result of this investigation, a method of alloying and fabricating copper alloys containing 10 to 15 pct iron was developed

Jan 1, 1949

By Frank E. Hauser, Philip R. Landon, John E. Dorn

The flow and fracture strengths of polycrystalline aggregates of high purity magnesium and a solid solution of aluminum in magnesium were determined as functions of temperature and grain size. Magnesium was found to obey two distinct fracture laws. Over the high temperature range, the fracture stress decreased with increasing test temperatures in a manner that closely paralleled the flow stress-temperature relationship. However, over the low temperature range, the fracture stress was independent of the test temperature though highly dependent on grain size, following the trend that is typical for the low temperature brittle fracturing of polycrystalline aggregates of body-centered-cubic and close-packed-hexagonal metals. Even at 78°K, however, plastic strains of 1 to 7 pet were obtained preceding onset of brittle fracturing. Over the brittle fracture range of temperatures, the fracture stress increased linearly with the reciprocal of the square root of the mean grain diameter, while over the entire range of temperatures investigated, the flow strength was observed to increase linearly with the reciprocal of the square root of the mean grain diameter. PREVIOUS investigations&apos;, &apos;have shown that deformation of coarse grained aggregates of high purity magnesium is interrupted by fracturing at very small strains. Such tendency toward brittle fracturing increased with increasing grain size and decreasing test temperature. In several respects, however, low temperature fracturing of magnesium appeared to differ from the truly brittle type exhibited by zinc, molybdenum, tungsten, and iron, so often characterized as a cleavage mode of fracturing. The absence of a well-defined cleavage mechanism for fracturing and the fact that some plastic deformation precedes fracturing might suggest that magnesium does not exhibit the same kind of brittle fracturing that is common to body-centered-cubic metals and to other close-packed-hexagonal metals. But, as will be shown, the low temperature fracture laws for magnesium are analogous to those that apply to iron, molybdenum, tungsten, and zinc in spite of differences in mechanisms and in plastic strains to fracture. In view of these observations. the low temperature fracturing of magnesium will also be called brittle fracturing. This, of course, does not imply that the brittle fracturing of metals is synonymous with the brittle fracturing of glass or other nonmetallics. Whereas the brittle fracturing of glass probably obeys Griffith&apos;s law, the low temperature brittle fracturing of metals arises from stresses induced by a series of dislocations piled up at an opaque grain boundary. Experimental Results All tests were made on tensile bars having gage sections that were 2 in. long and 0.375 or 0.25 in. wide. In order to develop a series of grain sizes, the

Jan 1, 1957

By George R. St. Pierre, John Chipman

METALLURGISTS have been studying the chem-ical behavior of sulfur in steelmaking for many years in order to have a better control of the sulfur content of finished steel. During the refining period in the open hearth, molten steel is separated from a gas phase by molten slag. Chemical reactions occur principally at the slag-metal interface and at the slag-gas interface. A need for physical-chemical investigations of reactions between sulfur-bearing gases and steelmaking slags was recognized some time ago.&apos;.&apos; From the early work, it can be qualitatively concluded that increased sulfur content and low partial pressure of oxygen in the gas phase favor the passage of sulfur from gas to slag. Using radioactive sulfur S Koch and Fink&apos; have demonstrated the rapid rate of exchange of sulfur between gas and slag in an open hearth furnace. Gurry and Darken and Darken and Shields (as reported by Derge and Marshall&apos;) have equilibrated lime-iron oxide slags with SO—O2 gas mixtures. The major conclusion from the reported results is that sulfur content increases with increasing lime content in lime-iron oxide slags equilibrated with a gas of high oxygen pressure (10-2). The data were interpreted as indicating the presence of SO, and S,O, ions. Richardson and Fincham&apos; have conducted the most extensive experimental study of sulfur equilibria between gas and slag. Their results confirmed many of the conclusions drawn from calculations of Richardson" and Withers. Richardson and Fincham&apos;s data fitted very well into the sulfur scheme represented by the reactions 1/2 s2 (g) + (0) melt - 1/202(g)+ (S) melt [II 1/2 S, (g) + 3/2 O (g) + (0) melt - (SO,) melt. [2] At oxygen pressures greater than 10 to 10 they found that reaction Eq. 2 was predominant while reaction Eq. 1 was controlling at oxygen pressures less than 10." to 10.". The slag compositions and gas mixtures used in their investigations were different from those used in the present study. Wherever possible, comparison has been made between their results and these, and agreement is excellent. It is evident that the distribution of sulfur between slag and gas depends upon the oxygen pressure of the gas. In FeO slags, a change in oxygen pressure produces a change in ferric oxide content, and a knowledge of this equilibrium is a prerequisite to studies of sulfur distribution. The data are found in the work of Darken and Gurry" on the FeO system and the more recent experiments of Gurry and Darken" and of Larson and Chipman" on FeO slags containing lime and silica. The effect of oxygen pressure on the ratio Fe /(Fe" + Fe ), the so-called j-ratio, reported by these investigators will be used in interpreting the results which follow. Experimental Method The purpose of the experimental program was to determine the equilibrium sulfur content in slags exposed to gases of known oxygen and sulfur pres- sures. The slag compositions selected for study were from the lime-silica-iron oxide system. Additions of magnesia were made to some of the slags. Apparatus—The apparatus used by Larson and Chipman was modified slightly to accommodate the addition of SO2 to the gas mixtures. As in their work, slag samples of 0.5 to 2.0 g were held at temperature (lcc) in platinum crucibles under a steady stream of gas, 100 to 200 ml per min, for several hours and then rapidly lowered to the bottom of the furnace where they were quenched in mercury. Preparation and Analysis of Gas Mixtures—Mixtures of SO,-CO were prepared from Virginia Smelting Co. Extra Dry liquid SO, and Pure Co. CO,. After removing traces of water vapor with an-hydrone, the CO, was passed over graphite at 1200°C, at which temperature the conversion to

Jan 1, 1957

By R. W. Raymond

I HAVE the pleasure of exhibiting samples of the rock in which the South African diamonds are said to occur, for which I am in debted to Mr. Franz Groeger, of Vienna, formerly an assistant of the Royal Imperial Geological Institution, whose account of the general geology of Southern Africa was contained in a recent number of the proceedings of that Institution. The rock is apparently a sort of tufa, evidently of volcanic origin. Mr. Groeger assured me that it could be seen in situ, bounded by uplifted stratified rocks; and that diamonds had been mined from it, by means of shafts, some distance below the surface. Groeger calls it "greenstone-tufa," and says of it, in the proceedings of the Geological Institution, " it breaks through the younger members of Group III [lower Trias and Jura], . . .. and crops out in oval masses, filling fissures . . ..The occurrence of this tufa is not locally limited, but has been traced and proved already over a large territory." DR. HUNT remarked that the material looked like the trass of the Rhine region. He thought it a new occurrence for diamonds. He believed diamonds to belong to ancient crystalline rocks, although these materials might be brought tip by volcanic agency, and the diamonds remain unaltered. In the volcanic rocks of Auvergne, crystals of sapphire, zircon, and spinel are found; and yet no one supposes that these minerals have been generated by volcanic agency. He had had a conversation with Bertrand de Lom on this subject, who agreed with him that these minerals, being hard and resistant,

Jan 1, 1874

By AIME AIME

THE session on milling methods on Monday afternoon.* with G. H. Clevenger, chairman of the Mining Methods Committee presiding, was well attended. However, none of the authors of the papers presented were present except Messrs. Taggart and Ince. The paper on "Elements of Operations of the Pneu¬matic Table," by Messrs. Taggart and. Lechmere-Oertel, was presented by Professor Taggart as was the paper on "Calculations in Ore Dressing," by Luyken and Bierbrauer, due to the absence of the authors.

Jan 1, 1929

Discussion of the paper of BOYD DUDLEY, JR., presented at the New York meeting, February, 1915, and printed in Bulletin No. 96, December, 1914, pp. 2767 to 2782. H. 0. HOFMAN, Boston, Mass.-At the close of the paper Mr. Dudley said that his experiments in the laboratory had shown that it was possible to separate nickel from copper by means of a chloridizing roasting, but that in order to demonstrate a process of this kind, work upon a large scale would have to be carried out. I think it was in 1913, that experiments of this kind were carried out at the works of the Pennsylvania Salt Manufacturing Co., Philadelphia, in a Wedge furnace, and at Sault Ste. Marie in a Sjöstedt furnace. They showed a satisfactory separation of nickel and copper. The ore was first subjected to an oxidizing roast, then mixed with pyrite and salt, and given a chloridizing roast. A. H. Carpenter published in the Engineering and Mining Journal, vol. xcvii, p. 1085 (1914) the details of this work. The conclusion arrived at is, that if you subject sulphide ore to an oxidizing roast, finishing at the temperature at which all nickel sulphate is dissociated, i.e., 764° C., then mix it with pyrite and salt, and subject the mixture to a chloridizing roast between 600° and 700° C., you can chloridize a high percentage of the copper without chloridizing any of the nickel, and obtain thereby a satisfactory means of separating the two.

Jan 5, 1915

By B. B. Cox

The principal event during 1936 was the sale of Mosul Oilfields, Ltd. to Mosul Holdings, Ltd., a British company with French and American participation, and the expansion of its wildcat activities to untested structures on its West Tigris concession. Mosul Holdings continued the exploration of its low-gravity Qaiyarah-Najmah-Jawan-Qasab field. The Iraq Petroleum Company&apos;s systematic exploration and exploitation of its Kirkuk field was continued on a scientific unitized basis. Pressures and gas-oil ratios remained satisfactory. All wells were produced by flowing. A stabilization plant large enough to supply the 4,000,000-ton pipe line to the Mediterranean was completed at Kirkuk about the close of the year and only sweet oil is now being exported. The Khanaqin Oil Co., Ltd., a subsidiary of the Anglo-Iranian Oil Co., Ltd., continued the normal exploitation of its Naft Khaneh oil field, refining and marketing through the Rafidain Oil Co., Ltd. for local Iraq market. This field lies partly on the Iraq side of the boundary and partly on the Iranian side, the latter portion being known as Naft-i-Shah. Only the Iraq side is considered in this paper. Slightly more than 30,000,000 bbl. of crude was produced in Iraq during 1936. The I.P.C. exported all crude sold outside of Iraq and showed an increase of about 2,500,000 bbl. over the preceding year. Crude production in Iraq for export in 1934 was 7,096,669 bbl.&apos;; in 1935 it was 27,014,904 bbl. and in 1936 it was 29,521,053 barrels.

Jan 1, 1937

By John E. Young

U.S. Steel Corp.&apos;s Winifrede mine is operated by Lynch District in the mountainous region of eastern Kentucky. This region is characterized by narrow finger ridges and precipitous slopes, which present both an opportunity and challenge in the design and selection of coal-handling facilities for the movement of coal from the section belts to the railrod cars. Lynch District selected diesel-powered locomo¬tives and 100-ton articulated cars capable of negotiating sharp curves. The drop¬bottom mine cars are equipped with longitudinally hinged doors that are auto¬matically opened and closed. Lynch District selected a large-diameter steel-lined borehole for lowering the coal approximately 1000 ft from the seam level to the valley floor railroad load-out point. Taking advantage of gravity, the presized coal is "lowered" vertically approximately 720 ft to existing entries of a previously abandoned mine. The coal is then conveyed horizontally into storage. The coal¬handling facility from the mine-car dump to the railroad load-out point is fully automatic through use of tone control. TV cameras are installed along the facility to continuously monitor the strategic points. The diesel locomotives are either directly operated or remotely radio-controlled, depending on the functions Per¬formed. U.S. Steel Corp.&apos;s Winifrede mine is operated by Lynch District in the mountainous region of eastern Kentucky. This region is characterized by narrow mountain ridges and precipitous slopes which present both an opportunity and challenge in the design and selection of coal-handling facilities for the movement of coal from the section belts to the railroad cars. The narrow finger ridges precluded use of under¬ground haulage and, thereby, presented the opportunity to use high-capacity equipment on the outside bench. The precipitous mountain slopes, steepest at the Wini¬frede seam horizon, presented a challenge to select a solution for lowering the coal approximately 1000 ft from the seam level to the valley floor railroad load-out point. It was evident from the start of planning that these two factors predominated; namely, rail haulage and coal lowering, and solutions to these would determine the final design of the Winifrede mine coal-handling facilities. The Winifrede mine derives its name from the Wini¬frede Seam which comprises the total reserve recov¬erable from this facility. The seam is 5 ft high with a good siltstone bottom and competent shale or sandstone roof. The seam is at an elevation of 2700 ft where the mountain ridges are long and narrow. This configuration of the reserve was ideal for conveyor belt installation to transport the coal from the working face to the outside bench. The preclusion of underground rail haul¬age permitted an opportunity to review the type of locomotive power and to select high-capacity equipment without the limitations associated with underground systems. Since the basic electrical design of the mine was al¬ternating current, with rectification to direct current for shuttle cars required only in the face areas, there was no point in bearing the burden of additional cost of dc trolley installation. And, since the haulage would re¬quire only a few tunnels to negotiate sharp points and to reach the back side of the reserves, diesel power was selected for the haulage locomotives. To provide stability on the almost continuously curv¬ing track and to provide the maximum width of haul¬age equipment, both locomotives and mine cars, stan¬dard railroad gage was chosen to offer the largest choice of equipment. The decision was made to select a standard 45-ton railroad diesel locomotive but to lower the cab height to reduce tunnel excavation requirements. The mine car was the next challenge. Past experience in Lynch operations indicated that drop-bottom cars would be a successful application with the free-flowing coal. The search was for a drop-bottom car within the dimensions of the locomotive to discharge the coal in the shortest time. Numerous types were considered and visits made to various sites to observe cars in operation.

Jan 1, 1972

By Daniel Martin

THE dendritic pattern of steels shown by deep etching is used exten-sively as a guide in the inspection and control of the great majority of steels used in ordnance construction and for many applications in indus-try. The value of macroexamination lies in the fact that it enables a qualified observer to make deductions concerning the general quality of relatively large pieces of metal. Not the least of these general character-istics is the nature and extent of the dendritic segregation in the steel, either in the cast condition or after mechanical or thermal treatments. PREVIOUS WORK Detailed methods for macroetching were outlined by Yatsevitch1 and have been standardized by the American Society for Testing Materials. A comprehensive study of the occurrence, origin, and the chemical and crystalline nature of the dendritic structure was given by Keshian.2 The marked persistence of dendritic segregation in nickel steels is fully recognized and has been discussed by Sauveur and Reed&apos; and by others. Very little, however, has been written on the effect of the various elements on the macrostructure of steels, and the purpose of this report is to submit evidence concerning the influence of chromium, nickel and molybdenum on the macrostructure of some 4 by 4-in. ingots cast and treated under closely controlled conditions.

Jan 1, 1939