Search Documents

By A. L. Benham, W. E. Dowden, W. J. Kunzman

The mechanism involved in creating a miscible fluid displacement of typical reservoir fluids through porous media by light hydrocarbon mixtures usually involves a number of mixing and separation stages in the contact area. This mechanism has been illustrated on ternary diagrams for miscible displacement of reservoir fluid by rich hydrocarbon gases. A relatively simple method has been devised for calculating the approximate conditions for a miscible displacement of reservoir fluid by rich, light hydrocarbon gases or by LPG mixtures. Miscibility is favored by increased pressures, decreased temperatures, light reservoir fluids and light hydrocarbon-displacing fluids rich in the heavier components. The conditions for miscible displacements of five typical reservoir fluids by various light hydrocarbon mixtures were determined for a range of temperatures from 70" to 260°F and pressures from 1,000 to 3,000 psia. A correlation of these conditions was obtained using the variables of temperature, pressure, C,+ molecular weight of the reservoir fluid, C,+ molecular weight of the displacing fluid, and mol per cent methane in the displacing fluid. This correlation has been applied to data appearing in the literature with very good success. A partial check of the correlation has been made using a step-wise procedure with a windowed PVT cell. INTRODUCTION The term, "miscible fluid displacement", may be defined as any oil-recovery displacement process where there is an absence of a phase boundary or interface between the displaced and displacing fluids. A water flood would not be a miscible fluid displacement, although cycling in a condensate reservoir would be. Another example is displacement of oil by gasoline. Not so obvious, however, are the conditions under which fluids (such as propane, mixtures of propane and methane, or other similar systems) will give a miscible fluid displacement of oil. There are four standard miscible-fluid-displacement processes being used for the recovery of oil from an "nderground reservoir—(1) high-pressure dry-gas miscible displacement, (2) rich-gas miscible displacement, (3) miscible slug using a slug of LPG followed by a lean dry gas under miscible conditions, and (4) gas driven-slug process using a slug of LPG followed by a lean dry gas under immiscible conditions. The first problem faced by the engineer designing a miscible displacement process is to determine the conditions for miscibility. A number of papers have included discussions of the process of obtaining miscibility in these processes.1-8 However, methods for calculating the conditions for miscibility have not been published. This paper includes a method for calculating the conditions for a miscible displacement of reservoir fluid by a rich gas (LPG diluted with methane or natural gas). In this paper, a rich-gas miscible displacement process is defined as an oil-recovery process in the reservoir. The cost of a rich-gas miscible displacement will be decreased by diluting the LPG with methane or natural gas as much as possible. Therefore, it is important to be able to predict the maximum dilution for miscibility. MECHANISMS The mechanisms for obtaining miscibility between a displacing mixture of light hydrocarbons and displaced reservoir fluid often involve a number of displacing and mixing stages. As stated previously, the cost of a rich-gas miscible displacement is decreased by diluting available LPG with natural gas. The problem is to predict the maximum dilution allowed while maintaining miscibility. To get a picture of the displacing and mixing stages, it is helpful to consider these complex hydrocarbon mixtures as pseu do-ternary systems. Graphical representation of a complex system as a pseu do-ternary system can be thermodynamically rigorous if enough variables are used to describe the character of each pseudo-component in one of the phases. However, even if the characterization of each pseudo-component is not complete, pseudo-ternary representation does serve to illustrate the mechanism for obtaining miscibility and can be used to make some general conclusions concerning the conditions for obtaining miscibility. A phase diagram for the ternary system, methane-

By H. L. Hopkins, OHIO, L. W. Kemph, CLEVEL AND, E. V. Ivanso

A balanced system of internal stress is set up in any metallic structure by plastic deformation below the annealing temperature. The internaI stress induced by cold rolling or other fabricating processes is generally recognized and its magnitude is known to be, within certain limits, a function of the degree of cold deformation. The plastic deformation that may accompany rapid cooling from elevated temperatures may not materially change the form of the product. The internal stresses so induced are not, therefore, so evident and nonrecognition of their presence has at times led to engineering failures. The heat treatment of aluminum alloys is a relatively new art and little information is available regarding the magnitude of stresses induced during the commercial heat treatment of aluminum alloy products. As the industrial use of aluminum increases, it is inevitable that products of increasingly large volume will be required. It has become necessary in the present commercial utilization of aluminum to heat-treat castings and forgings weighing hundreds of pounds. One of the factors governing the magnitude of internal stresses arising from rapid cooling from elevated temperatures is that of the size of the structure being treated. Some of the other factors are: cooling rate, elastic properties of the alloy, thermal expansivity, thermal conductivity, and the presence or absence of phase changes. Practically all aluminum alloys have a high coefficient of thermal expansion and some are capable of developing relatively high elastic limits. On the other hand, all commercial aluminum alloys have relatively high thermal conductivities, no invariant phase changes, and the quenching temperatures are comparatively low. In the absence of invariant phase changes involving change in the type of crystallographic lattice, the fundamental basis for the development of internal stress

Jan 1, 1934

By S. H. Ash

Diesel locomotives, trucks, bulldozers, and other diesel-powered equipment are fast proving their superiority for mine transportation purposes. MORE than 100 minerals are mined and processed in the U. S. Management and labor have negotiated wage-scale agreements that have balanced wages and affected cost of labor in such a manner that comparisons can be made of transportation costs. Transportation of materials underground has become of vital importance.1"0 This report describes underground haulage methods and equipment, presents cost analyses, and discusses future plans for underground transportation in metal mines. It does not cover hoisting in shafts or slopes by cage, skip, or cars. Advancements have been made by the metal mining industry in lowering transportation costs in several mines, making it possible to mine orebodies or portions of orebodies not considered economically recoverable a few years ago.7,8 Wumerous reports have been written on transportation at metal mines; this report covers recent haulage at some representative mines throughout the U. S. The term metal mine is used to include all noncoal mines from which up-to-date information was obtainable. The best haulage equipment is subject to break- downs and accidents; but unless the rolling equipment, track, and signal systems are kept in good repair and are operated systematically, these breakdowns and accidents are likely to be frequent, destructive, and more costly than are necessary.10 Rail haulage crews using dependable rolling stock can move trips safely over grades low enough to be traveled without loss of control; this applies particularly if the track is straight and well maintained. Few accidents occur on main haulage lines if visibility and clearance are good and clear track is assured. One-way traffic underground is a recent development contributing to reduction of accidents and increased efficiency in mine haulage (Kelly mine, Anaconda Co., Butte, Mont., and Climax mine, Climax Molybdenum Co., Climax, Colo.)." Locomotives: Six types of mine locomotive used in recent years are trolley, storage battery, combination trolley and storage battery, diesel, compressed air, and gasoline. Electric haulage has been displaced by compressed air locomotives, which have been used successfully in certain instances, especially on dirty and wet tracks and steep grades." Maintenance cost is high, and operating efficiency, from a power standpoint, is low. Compressed air locomotives operate under self-contained power, and the absence of bare elec-

Jan 1, 1957

By Douglas W. Fuerstenau, Kalanadh V. S. Sastry

A mathematical model is developed for flotation in a countercur-rent column where continuously generated air bubbles rise through a downward flowing pulp. The model is based on the assumption of axially dispressed plug flow of both the liquid and air-bubble phases. An appropriate flotation-rate expression, which takes into account the changing concentration of solid particles on the bubble surface, is formulated and applied to the column flotation process. Although a complete solution of the resulting equations is not possible for the general case, solutions for specific limiting cases have been obtained. From these, it is possible to predict theoretically the dependence of the column performance on certain variables. Specifically, concentration profiles as a function of height in the column have been calculated for various values of the characteristic dimensionless parameters. The effect of axial dispersion on the perforance of the equipment is pointed out. In recent years, there has been considerable progress in delineating the fundamental physicochemical principles underlying the unit operation of flotation and in advancing methods for kinetic analysis and process modeling of flotation.' In general, nearly all such process research has been concerned with the analysis of conventional flotation equipment and circuits. From these investigations, the possibility of developing and designing flotation apparatus for more efficient separation appears limited with conventional equipment. How- ever, recently there has been an attempt to apply coun-tercurrent flow techniques to flotation in the context of a flotation column.- some of the results from pilot-plant studies2 indicate possibilities for success of this process at least in obtaining higher-grade concentrates though not higher recoveries. A flotation column operates on countercurrent principle in which bubbles continuously generated at the bottom of the column rise through the downward flowing slurry. A schematic diagram of the flotation column is shown in Fig. 1. The physicochemical principles of bubble-mineral attachment, using this flotation column, are essentially the same as those which prevail in conventional equipment, the only differences being in the flow patterns of the various phases. The salient operating feature of the column as compared to those of a conventional cell is that neither mechanical nor turbulent pneumatic agitation is employed. The column is

Jan 1, 1971

By H. Kazemi

An ideal theoretical model of a naturally fractured reservoir with a uniform fracture distribution, motivated by an earlier model by Warren and Root, has been developed. This model consists of a finite circular reservoir with a centrally located well and two distinct porous regions, referred to as matrix and fracture, respectively. The matrix has high storage, but low flow capacity; the fracture has low storage, but high flow capacity. The flow in the entire reservoir is unsteady state. The results of this study are compared with the results of the earlier models, and it has been concluded that major conclusions of Warren and Root are quite substantial. Furthermore, an attempt has been made to study critically other analytical methods reported in the literature. In general, it may be concluded that the analysis of a naturally fractured reservoir from pressure transient data relies considerably on the degree and the type of heterogeneity of the system; the testing procedure and test facilities are sometimes as important. Nevertheless, under favorable conditions, one should be able to calculate in-situ characteristics of the matrix-fracture system, such as pore-volume ratio, over-all capacity of the formation, total storage capacity of the porous matrix, and some measure of matrix permeability. INTRODUCTION The analysis of flow and buildup tests for obtaining in-situ characteristics of oil and gas reservoirs has received considerable attention in the past decade. Most of the available techniques result in reliable conclusions in macroscopically homogeneous reservoirs or in the homogeneous reservoirs with only certain types of induced and/or inherent heterogeneity (such as wellbore damage, etc.). In general, the greater the degree of heterogeneity, the less the reliability of the information deduced from the pressure transient data. A commonly encountered heterogeneous system is a naturally fractured reservoir where two types of distinct porosities occur in the same formation. The region containing finer pores may have high storage and low flow capacities. This is called the matrix. The remaining region may have high flow capacity with low storage. The latter region is generally the set of interconnecting fractures and fissures of the rock, and for this reason it is called the fracture. Ordinarily, we wish to obtain the permeability and porosity of each region and perhaps the frequency of the fracture distribution in a reservoir. Such information is necessary for reservoir engineering. Other information, such as wellbore damage, will be useful in evaluating possible remedial work for such fields. Few authors have suggested theories to aid in calculating the in-situ characteristics of a naturally fractured reservoir similar to what we have described above. Pollardl suggested that a naturally fractured reservoir contained three distinct regions: a damaged or an improved region surrounding the wellbore, and the two remaining regions the same as described earlier. He suggested that the flow was taking place from the tight matrix into the highly conductive fractures, then into the we wllbore region and finally into the well column. He concluded that the average pressure buildup in each of these distinct regions can be expressed approximately in terms of an exponential decay function of time. He also hypothesized that the decay coefficients for each of these functions were significantly different from each other; consequently, each of these functions became dominant in turn, in the process of pressure buildup. Thus, by a proper graphic plot of the logarithm of wellbore pressure differences vs buildup time, each of these functions could be determined (see Fig. 1). Pollard suggested methods of determining the wellbore damage and fracture volume. Later Pirson and Pirson2 extended

Jan 1, 1970

By S. K. Tarby, W. O. Philbrook

The rate of FeO and MnO reduction from silicate and aluminate slags by carbon-saturated iron is dependent on both slag composition and temperature. Owing to variable stirring rules during- the course of reaction, the reduction processes occur in two stages in stationary graphite crucibles. In the first stage the slirring caused by CO evolution results in forced convection conditions in the slag. As the boiling action subsides during reduction, the flow conditions within the system become those defined by natural convection. Analysis of the data by an unsteady-state penetration model indicates that the rate of reduction is controlled by the rate of cocur-rent flow of' cations and anions from the bulk slag to the interface during both stages of reduction. The hearth reactions of the blast furnace have been extensively investigated from the viewpoint of equilibrium by deductions from controlled laboratory experiments. However, the literature contains relatively few studies that have been directed toward the area of slag-metal reaction kinetics, and the majority of these have been concerned with the rate and mechanism of sulfur transfer between iron and slag. More recently, attention has turned to the kinetic factors in the reduction of oxides from liquid slags. One of the first investigations in this field was conducted by Dancy1 on the reduction of pure liquid FeO and pure liquid Fe3O4 by carbon-saturated iron. The integrated form of the rate equation indicated that the reduction of FeO was of the first order up to 80 pct reduction. Over the initial 30 pct of reduction, the magnetite reaction was also interpreted as a first-order process. The rates of reaction were extremely rapid as indicated by a 30 pct reduction of the liquid magnetite in a time interval of about 1 to 2 sec. Phil-brook and irkbbride' studied the reduction of FeO from a lime-alumina-silica slag by carbon-saturated iron and solid graphite in stationary crucible assemblies. With the use of the differential form of the rate equation, the rate of the reduction reaction was found to be proportional to the second power of the concentration of the reactant FeO for both the slag-metal and slag-graphite reactions. These authors presented a number of comments in an effort to explain the difference between the molecularity of the above reaction and the observed second-order relation. One such argument, recently extended by Wagner,3 was that the rate-limiting step may well be one of transport control. A complete discussion of the proposed mass-transport control mechanism of this reduction reaction will be presented in a later section of this paper. Kinetic studies of the reduction of other oxide species, namely chromous oxide, titania, and silica, have also been reported. McCoy and philbrook4 used rotating crucible assemblies to investigate chromium reduction from Ca0-SiO2-A12O3 slags. First-order kinetic law was obeyed for the slag-metal reduction reaction as determined by the integration method of data analysis. Due to scatter of the data, any dependence of the rate constant on temperature or slag composition was obscured. Concentration-time data for the reduction of titania from blast-furnace type slags under reducing conditions were obtained by Delve, Meyer, and Lander.' The data were too few, however, for a formal kinetic interpretation. Kinetic data for the very slow reaction of silica reduction have been observed by McCoy and Philbrook6 and Fulton and chipman.7 The former experimenters found the reaction-rate constant for silica reduction by carbon-saturated iron to be 20 to 60 times less than the rate constant for chromium reduction. In their work on the reduction of SiO2 in mechanically stirred systems, Fulton and Chipman also found small values for the specific reaction rate and derived a high value for the energy of activation for the reaction. In both of these investigations, the reduction process was assumed to follow first-order behavior. schuhmann8 proposed that the rate-limiting step in this reaction is the diffusion of oxygen from the interface through a boundary-layer film to the bulk metal phase, and Rawling and Elliott9 have reported experimental confirmation of this hypothesis for temperatures below 1600°C. Turkdogan et a1.10 have also concluded that the rate of reduction of silica is a slow process and controlled by the diffusion of oxygen in the metal, but only in the absence of carbon monoxide bubbles at the slag-metal interface. In the presence of bubbles, achieved either by injecting carbon monoxide at the slag-metal interface or by blowing it through the metal and slag, these investigators found a rather rapid reduction of silica which appeared to be controlled by an interfacial reaction involving the de-sorption of silicate ions from the slag-metal interface to the metal phase as silicon and oxygen atoms. In view of the unresolved nature of the kinetics of FeO reduction and the lack of kinetic data for the manganese reaction,

Jan 1, 1968

By J. C. Bradbury

The year of the Centennial is upon us. Not only is AIME marking its 100th birthday, but the cement industry is also celebrating 100 years of activity (see article by Roy Grancher, page 48). Fort Dodge, Iowa, and gypsum also tried to get into the act but missed by one year. Frank Apple-yard's gypsum article (page 53) informs us that the Fort Dodge area has been producing gypsum continuously for 99 years. That would seem to make AIME and the industrial minerals doddering oldsters. Not so-our Institute shows more energy than ever, and the word for industrial minerals is growth. These are the mineral resources of the future, the raw materials for the abundant life to come

Jan 1, 1971

By Paul L. Burkhart

THOUGH at an earlier period brief studies had been made by the Lehigh Navigation Coal Company Inc., it was not until 1924 that J. B. Warriner, then general manager, called for a comprehensive study of timber treatment, treating solutions, and related operations. Because of the impossibility of procuring accurate costs and other pertinent treating data, the American Wood Preserving Co. agreed to treat a car of mine timber at the Port Reading plant of the Reading Railroad. Fig. I shows the treating data collected at the treating plant on this timber, which was installed in two of the Lehigh mines in 1925. [ ] In the latter part of 1925, a survey of the tunnels and gangways of the company's Panther Valley mines was made to determine the proportion of gangways or tunnels timbered, cause of timber failures, approximate life of the average wood set and the approximate percentage of treated timber that it would be profitable for the company to use. Results of this survey appear in Table I. Because of the high percentage of timber that gave evidence of failure by rot, as noted in Table I, and a further study of the life of the sections where timbering was necessary, it was deemed advisable to fill 25 per cent of the yearly gangway timber requirement with treated timber. QUANTITIES AND TREATMENTS OF TREATED TIMBER PURCHASED In the early days of the program, none of the large treating companies would accept orders for small quantities of treated timber and the company was compelled to state the quantity of timber it would require at each operation in each month of the year. Table 2 is an example of the tabulation given to the various treating companies to assist them in making a yearly bid on the minimum quantity of timber required by the company during the year 1931. A bill of timber was calculated for each car, the weight of which would be between the minimum and maximum weight permitted for railroad-car loading. The treating company was paid for timber upon delivery at the operation specified. As extra cars of timber were required, they were ordered from the treating company, and payment was required on their receipt, on the basis of the piece or tonnage

Jan 1, 1942

By L. R. Raymond, J. L. Hudson

This paper proposes a comparatively short-term (8 to 10 hours) well test for detecting and characterizing well-bore damage and for measuring mean formation permeability. The proposed test is made by injecting fluid at constant pressure, recording injection rate as a function of injection time. After one to four hours of injection, the well is shut in and fall-off of bottom-hole pressure is obtained as a function of shut-in time. Formation permeability is estimated by an iterative technique. First, a value of formation permeability is assumed. Then, a plot of the recorded injection rate as a function of dimensionless time is made, using the assumed pertneability value. From the slope of the injection-rate curve. a new value of formation permeability is calculated. If the new value agrees with the original assumed value, the assumption was the correct formation permeability. If the values do not agree, the process is repeated using the new permeability value in the calculation. Convergence is rapid, and a reliable permeability value results. Pressure fall-off data are used to check the result. Graphs of pressure and injection rate us functions of time given in the paper show that changes in permeability of the formation in the neighborhood of the wellbore are disclosed by this technique. Thus, the short-term test can he used to detect formation damage. Also, a rough measure of the radial extent of damage can be inferred, which is helpful in designing stimulation treatments. The mathematical model used for this work was a single-zone, horizontal reservoir with a damaged zone in which permeability decreased continuously as radial distance to the wellbore decreased. This model is more realistic than the usual two-zone, discontinuous permeability model used in published works; calculations indicate the realistic model is valid. Vertical variations in horizontal permeability were studied with this model, and results indicate that the permeability measured by the short-term test is the mean horizontal permeability for the vertical interval tested. The proposed short-term test thus should be useful in detecting and characterizing formation damage and in measuring formation permeability needed in calculating reservoir transmissibility. INTRODUCTION To plan the most efficient production or injection schedule for a well and to design or evaluate the optimal stimu- lation treatment, it is necessary to know the properties of the reservoir adjacent to the well, particularly the reservoir transmissibility and characteristics of a damaged zone, if one exists. Several techniques for determining reservoir transmissi-bility from well tests have been presented in the literature. 1,2,3,4 All these techniques rely on conducting constant-rate well tests that often are difficult to execute. A constant-pressure well test is generally easier to carry Out. and this paper contains the first available method for the analysis of constant-pressure well tests. Determination of wellbore damage from transient well tests has been the subject of several papers."" From these studies it is apparent that information necessary for determination of the characteristics of a damaged zone is available shortly after the transient well test is initiated. Consequently, it may not be necessary to carry out an extensive well test (for example, a pressure build-up test) if the primary purpose of the test is to detect the existence of wellbore damage. All previous studies of well testing to determine wellbore damage have been based on the two-zone perrneability model. In this model the damaged zone has a permeability k,, extending to a radius r,,, and the formation permeability k obtains from r, to the drainage radius r,.. Consequently, there is a discontinuity in permeability at r = r,,. This discontinuity can be eliminated by assuming a continuous variation in permeability through the damaged zone. The effect of this assumption on transient well tests is discussed in following sections of this paper. In addition, all formations have within them vertical permeability variations associated with lithology changes throughout the zone of interest. This paper also considers the effect of these variations on transient well tests. ANALYSIS OF CONSTANT-PRESSURE WELL TESTS The mathematical analysis associated with the injection of fluid at constant wellbore pressure into a single-zone, horizontal reservoir completely filled with a fluid of small and constant compressibility and constant viscosity is given in Appendix A. In this analysis it is assumed that the well is located at the center of an undamaged, circular drainage area. From this analysis, the formation permeability can be obtained as follows. 1, Estimate a value for the formation permeability k. 2. Prepare a plot of injection rate q vs

Jan 1, 1967

By C. K. Leith

At the outset I would like to make it clear that I do not enter this discussion in a controversial spirit, but in an attempt to contribute something helpful to an understanding of a difficult problem. I have too high regard for the- sterling quality of the work of the men who have studied this subject in detail to offer anything in the way of essential contradiction to their statements of fact. Difference of opinion arises from differing valuation of the possible alternative hypothesis which these facts suggest. Some degree of recrystallization in limestone contact zones has been recognized by many investigators. Earlier investigators, for the most part, assigned an important, if not the most important, ro1e to recrystallization in development of these zones. With the growing recognition of introduction of ores and gangue materials into the contact zone from igneous rocks through the medium of primary magmatic solutions, there has been a tendency to ascribe to this process most, if not all, of the chemical and mineralogical characteristics of the contact zonc. This has involved a correspondingly diminished emphasis on recrystallization of substances already there as a factor in the process, and in some cases even the complete elimination of this hypothesis. From detailed study of a few contacts, casual observation of others, and a general familiarity with the literature, some of us have been led in recent years to raisc the question whether the pendulum has not swung too far away from recrystallization toward direct introduction from igneous sources, and to argue for more recognition of the part played by recrysta11ization.l The inevitable sequence has been that those of us who have .taken this view have been charged, at least by inference, with emphasizing recrystallization to the total exclusion of the alternative process. Scientists, like other men, like to classify and pigeon-hole views under simple and definite designations, leaving out qualifications which would tend to make the classification more difficult to state. This has made the problem seem more definite and simple, but has tended to obscure the fact that the disagreement is primarily not one relating to essential facts, but one of

Jan 1, 1915

By B. C. Burgess

IN the first edition of this volume,44 feldspar was introduced as "the I commonest mineral of the crystalline rocks," usually in small grains associated with other minerals and commercially produced only from pegrnatites. Now other crystalline rocks, such as alaskites and granites, have become present or potential sources of feldspar. In addition, feldspar has encountered very vigorous competition from such substitutes as nepheline syenite and aplite. COMPOSITION AND PROPERTIES The feldspars form a group of which the principal species are orthoclase, microcline, albite, and anorthite. These are aluminum silicates of potassium, sodium and calcium. There are also a barium feldspar, celsian, and barium orthoclase feldspar, hyalophane, rarely found and of no commercial importance. None of the minerals in the feldspar group are found pure or nearly pure. The potash feldspars, orthoclase and microcline, nearly always contain some albite (soda microcline, an- orthoclase); the soda feldspars usually contain some anorthite (lime feldspar). There is a series of soda-lime feldspars known as plagioclase in which the albite and anorthite molecules replace each other in varying proportions from albite through oligoclase, andesine, labradorite, and bytownite to anorthite. Theoretical chemical composition of the principal feldspars is given in Table 1. The Whiteware Division of the American Ceramic Society sub- mitted a list of definitions of ceramic terms, in April 1947, for use in technical literature. For feldspar it gives: "A group of igneous minerals consisting chiefly of the aluminum silicates of potash, soda and lime, in which one base generally predominates." Commercial feldspars are intergrowths of at least two species of feldspar, which occur associated with one or more accessory minerals such as quartz, muscovite, biotite, garnet and tourmaline as well as with small but varying proportions of the decomposition product, kaolinite. An intergrowth of quartz and feldspar frequently contains

Jan 1, 1949

By F. B. Richards

THERE has been much interest recently in the iron ore supply of the Lake Superior district. It may be of interest to this meeting to give some thought to this situation, dealing more particularly with the present great iron ore deposits of this section. Ores from its various iron ranges are the foundation of the tremendous tonnage of steel and iron of all kinds produced in the territory along and adjacent to the Great Lakes, drawing the bulk of its supply from this northwestern ore country. For a number of years estimates have been made of the quantity of available ore. The latest study, by M. C. Lake, chief geologist of the M. A. Hanna Co., is of great interest and brings the estimated tonnage to Jan. 1. 1929.

Jan 1, 1930

Although the 71 Minerals operation is now closed down and the operating data presented is almost five years old, it is well worth describing since it was the first heap leaching operation conducted on a primarily silver ore. Tombstone was discovered in 1877 by Ed Schieffelen; and it became one of the most famous mining towns in the West through the stories connected with Wyatt Earp, Doc Holliday, and the Clanton brothers. Like many silver deposits .in the western United States, the Tombstone ores were relatively shallow. Several million ounces of silver were recovered in the relatively few years the camp was active; but mining virtually ceased by the early 1900s and was only continued in a small way until the 19409, a history similar to that of Tuscarora. The 71 Minerals operation was started in May 1975 and continued until late 1978 within the city limits of Tombstone on waste dumps; one was the' Lucky Cuss, Schieffelen's discovery, which had accumulated from the old underground operations. This waste material was mostly less than 50 mm (2 in.) in size, although there was some larger lumps. The grade was about 34 g Ag and 0.5 g Au per mt (1.0 oz Ag and 0.015 oz Au per st). The Tombstone dumps contained approximately 1,000,000 tons. The dumps and patented claims were held by a single owner, Tombstone Development Company, thus sufficient leaching material could be acquired from one source rather than dealing with a number of individuals, as is usual in putting together leaching ventures in old mining camps. 71 Minerals Ltd. was formed and a lease of the properties obtained. A site was selected close to the major mine dumps not far from down- town Tombstone. Pads approximately 90 m (300 ft) wide and 180 m (600 ft) long with an 8-degree slope were prepared using compacted old mill tailings as a base sealant on the pads. Mining was done at a rate of about 2,000 tons per day with a dozer, two scrapers, a front-end loader, and 30 ton trucks. The ore was dumped by the scrapers as it came from the dumps with no screening or crushing in 460 mm (18 in. ) layers and trimmed with the loader. Based on bulk sampling and laboratory testing, the majority of thegold and silver values were recovered within 30 days of leaching.

Jan 1, 1981

By B. H. Sage, W. N. Lacey

The results of an extensive experimental program relating to the effectiveness of gravel screens have been correlated. The factors considered in some detail include gravel size and condition of packing, sand size and size distribution, fluid velocity, fluid viscosity, and thickness and arrangement of grave! screens. Good agreement between calculated values based upon probability considerations and experimental results relating to the influence of the thickness of the gravel screen was obtained. All of these factors are treated in the correlation in order that their influence may be taken into account in ascertaining the characteristics of an effective gravel screen for a particular set of conditions. The details of the experimental program are not given in the present paper but a description of generalized behavior and typical experimental results are recorded in graphic form. Introduction Gravel screens have been placed in water and oil wells for a number of yearsl,2,3 with the dual objective of increasing the productivity and decreasing the entrance of sand into the well bore. An understanding of the factors controlling the effectiveness of gravel screens in this connection is of industrial interest because it will lead to the proper selection of gravel. Some of the fundamental considerations involved in the migration of sand through a coarser body of porous materials were investigated by Coberly and Wagner4 and further experimental work has been carried out by Gumpertz.5 Apparently the pertinent phenomena are somewhat complex and are influenced by many variables. The present paper deals with the prediction of the behavior of gravel screens under the conditions encountered in practice but does not attempt to discuss the experimental methods or results that were obtained as a background and upon which the prediction is based. Influence OF Gravel Screens upon Productivity The use of a gravel screen may increase the productivity of a well by increasing its effective diameter, and this constitutes one of the objectives of its use. The permeability of most gravels and coarse sands that are employed in practice is so large compared to that of the sand in place that relatively little loss in production rate will arise from the use of material fine enough to cause the desired resistance to sand migration. For example, in Fig. I is depicted the approximate variation in the permeability of closely sized spherical gravels under the conditions of packing likely to be encountered in screens. The dotted lines indicate the variation that might be found because of differences in packing. It should be realized that the permeability is not a single-valued function of the average grain diameter but is related to a large number of factors, including the size, the size distribution and the shapes of the particles. However, Fig. I does permit a rough estimation of the permeability of closely sized spherical gravels and shows that the permeability with even the smaller particles is very large compared to that of most petroleum production horizons.

Jan 1, 1942

By W. N. Lacey, B. H. Sage

The results of an extensive experimental program relating to the effectiveness of gravel screens have been correlated. The factors considered in some detail include gravel size and condition of packing, sand size and size distribution, fluid velocity, fluid viscosity, and thickness and arrangement of grave! screens. Good agreement between calculated values based upon probability considerations and experimental results relating to the influence of the thickness of the gravel screen was obtained. All of these factors are treated in the correlation in order that their influence may be taken into account in ascertaining the characteristics of an effective gravel screen for a particular set of conditions. The details of the experimental program are not given in the present paper but a description of generalized behavior and typical experimental results are recorded in graphic form. Introduction Gravel screens have been placed in water and oil wells for a number of yearsl,2,3 with the dual objective of increasing the productivity and decreasing the entrance of sand into the well bore. An understanding of the factors controlling the effectiveness of gravel screens in this connection is of industrial interest because it will lead to the proper selection of gravel. Some of the fundamental considerations involved in the migration of sand through a coarser body of porous materials were investigated by Coberly and Wagner4 and further experimental work has been carried out by Gumpertz.5 Apparently the pertinent phenomena are somewhat complex and are influenced by many variables. The present paper deals with the prediction of the behavior of gravel screens under the conditions encountered in practice but does not attempt to discuss the experimental methods or results that were obtained as a background and upon which the prediction is based. Influence OF Gravel Screens upon Productivity The use of a gravel screen may increase the productivity of a well by increasing its effective diameter, and this constitutes one of the objectives of its use. The permeability of most gravels and coarse sands that are employed in practice is so large compared to that of the sand in place that relatively little loss in production rate will arise from the use of material fine enough to cause the desired resistance to sand migration. For example, in Fig. I is depicted the approximate variation in the permeability of closely sized spherical gravels under the conditions of packing likely to be encountered in screens. The dotted lines indicate the variation that might be found because of differences in packing. It should be realized that the permeability is not a single-valued function of the average grain diameter but is related to a large number of factors, including the size, the size distribution and the shapes of the particles. However, Fig. I does permit a rough estimation of the permeability of closely sized spherical gravels and shows that the permeability with even the smaller particles is very large compared to that of most petroleum production horizons.

Jan 1, 1942

By G. K. Williams

The continuous process of lead refining as at present operated at the Port Piric plant of The Broken Hill Associated Smelters Proprietary Ltd. was a development from investigations conducted in connection with the ordinary Parkes desilverizing process. It is not proposed here to discuss the theoretical considerations involved in continuous desilverizing because this aspect has already been dealt with in previous publications.1 Continuous Softening Process For economical desilverization of lead bullion, the bullion must first be subjected to refining processes for the removal of such impurities as copper, sulphur, arsenic, antimony and tin. This refining is effected by first drossing to remove copper and sulphur and then preferentially oxidizing the arsenic, antimony and tin from the bullion in the softening process. The theoretical basis of the continuous softening process is illustrated by the portion of the Pb-Sb-O ternary equilibrium diagram shown in Fig. 1. Under conditions of complete liquefaction, metal of the composition of softened bullion is in equilibrium with an oxide slag containing about 9 per cent antimony. In practice, of course, arsenic also is always present, and while the 0Pb-Sb-As-O quaternary system has not been worked out in detail, it has been found that in softening drossed smelter bullion of the composition produced at Port Pirie, arsenic is always reduced to 0.001 per cent or less when the antimony in the bullion is reduced to a satisfactory figure. In the operation of the continuous softening process, a two-phase system of a bullion low in arsenic and antimony and an oxide slag relatively high in those components exists in equilibrium. To this system is added continuously a bullion containing 0.2 per cent As and 0.8 per

Jan 1, 1937

By W. D. Robertson, W. L. Phillips Jr.

Stress-strain curves were obtained for single crystals of alpha brass in tension and in direct shear. Specimens were strained various amounts in a given slip direction, unloaded, and immediately strained in a second slip direction 60°, 120°, or 180&apos; from the original slip direction. Crystals strained in tension and direct shear had comparable critical resolved shear stresses and stress-strain curves. The density of slip lines in direct shear and in tension was essentially the same. The stress-strain curves obtained in shear were independent of initial orientation, choice of {111 } slip plane, choice of <110> slip direction, prior annealing temperature, and rate of cooling after annealing. There was no recovery after annealing for 4 hr at room temperature or 200°C; recovery was observed after 4 hr at 400°C. The crystals showed no asterism and mechanical properties were completely recoverable up to 20 pct strain. It was found that there is a barrier to slip in all latent close-packed directions, and that the magnitude of these barriers, evaluated at 3 pct strain, is proportional to prior strain and independent of the choice of latent direction in the {111} plane. The formation of Cottrell-Lomer barriers is discussed as a possible explanation for the hardening of the latent systems. AN idealized concept of plastic deformation indicates that a single crystal should yield at some stress that is dependent on crystal perfection and it should then continue to deform plastically by the process of "easy glide," which is characterized by a linear stress-strain curve and a low coefficient, ds/dE, of work-hardening. Hexagonal metal crystals generally conform to this ideal concept of laminar flow. In face-centered cubic metals the range of easy glide is always restricted in magnitude and it is strongly dependent on orientation, composition, crystal size, shape, surface preparation, and temperature. Since one of the principal differences between the two crystal systems, both of which deform by slip on close-packed planes, is the existence of secondary (latent) slip planes in the face-centered cubic crystals, it has been proposed that the transition from easy glide to turbulent flow, characterized by rapid linear hardening, is due to slip on secondary planes intersecting the primary plane.&apos;-.; However, the characteristic differences between individual face-centered cubic metals remain to be explained; in particular, it is not clear why the range of easy glide should vary so greatly in different metals and alloys similarly oriented for single slip. An investigation and comparison of different metals with respect to latent hardening on the primary slip plane should provide some of the information required to specify the necessary and sufficient conditions governing the transition from easy glide to turbulent flow. But, in order to accomplish this purpose, plastic strain must be produced by simple shear in a chosen plane and in a predetermined direction by some form of directed shear apparatus, the results of which must be correlated with the corresponding tension experiments. Two such experiments have been performed previously with zinc and with aluminum. Edwards, Washburn, and Parker" and Edwards and Washburn7 found that the strain-hardening coefficients in two latent directions in the basal plane of zinc were the same as in the primary direction. However, to initiate and propagate slip in either the [2110] or the [1210] direction, following primary slip in the [1l20] direction, it was necessary to increase the stress above that required to continue slip in the primary direction; when the direction of shear was reversed 180 deg plastic strain began at a much lower stress than that required to initiate slip in the original direction and the stress to propagate slip in the reverse direction was lower than the stress to continue slip in the forward direction, indicating a permanent loss of strain-hardening. Rohm and Kochendorfer observed softening in aluminum for all latent close-packed planes and directions. They also found that the critical resolved shear stress obtained from their direct shear apparatus was 50 pct lower than the value obtained from conventional tension tests, that the stress-strain curve was linear at 50 pct plastic strain, and that slip lines were not visible at strains less than 30 pct. At present it is uncertain whether these diverse results correspond to real differences in work-hardening characteristics of the close-packed planes of aluminum and zinc or to differences in experimental technique. In view of Read&apos;s analysis &apos;" of the stress distribution in the experimental arrangement of Rohm and Kochendorfer, there is some reason to question the significance of the latter results. In order to resolve this problem it is necessary to re-valuate the direct-shear technique and either repeat the previous measurements or investigate a third system. The latter choice seemed most likely to produce significant results with respect to work-hardening, and accordingly, it was decided to examine the hardening characteristics of the latent slip directions in alpha-brass. The choice of alpha-brass was dictated by the fact that easy glide is more extensive in this alloy than in any other face-centered cubic metal or alloy and, presumably, more nearly like the idealized hexagonal system. Experimental Procedure Crystals were made in graphite by the Bridge-man method in the form of cylinders, 11/2 in. diam and 8 to 9 in. long. Material for the crystals was 70/30 brass containing the following impurities:

Jan 1, 1959

By R. I. Jaffee, J. G. Dunleavy, H. R. Ogden, Webster Hodge

INTRODUCTION EARLY in 1946, at the instigation of the U. S. Army Signal Corps, the authors made an extensive survey of the available literature covering high-strength, high-conductivity alloys. For the purposes of the Signal Corps, the minimum tensile strength to be considered was 150,000 psi, together with at least 50 pct IACS conductivity. No single alloy was found to be in production, or mentioned in the literature, which had this combination of properties. The constitution diagram for the iron-copper alloys is not well established in the respect to the two-liquid region. Fig I, taken from the 1939 Ed. of the ASM Metals Handbook, shows a two-liquid system existing above the liquidus temperature, but disconnected from it. Although Ruer and Fick1 and Ruer and Goerens2 definitely established the fact that two liquid layers could occur in the system, Ruer3 was not convinced that the line off immiscibility was closed in the center. Maddocks and Claussen4 found no liquid immiscibility at temperatures up to 1570°C in alloys containing almost no carbon. Although the diagram would indicate age hardening of the copper-iron alloys is possible, Hanson and Fords found that little hardening effect could be obtained. However, Gordon and Cohen6 reported that the response is better if the quenching is very efficient. Although iron has a potent effect on the conductivity of copper, Hanson and Ford5 have shown that, when hot-rolled copper iron alloys are aged at 1200°F, the electrical conductivity decreases sharply with iron contents up to 0.2 pct Fe, and then levels off at conductivities between 60 to 70 pct IACS with compositions to 2.1 pct Fe. They also found that aging did not increase the tensile strength, although increasing iron content gave a moderate improvement in strength. High-strength copper-iron alloys, usually containing about 60 pct iron, had been reported by Smith and Palmer.7 They found that an alloy containing 56.4 pct copper, 0.21 pct magnesium, balance iron, would give a maximum tensile strength of 170,000 psi and an electrical conductivity of slightly over 35 pct IACS. The alloy could also be processed to have 150,000 psi tensile strength, and about 41 pct IACS conductivity. Decreasing the iron content increased the electrical conductivity, but the long mushy range during freezing of the alloy containing 10 to 20 pct iron made the production of good castings difficult, In spite of the difficulty encountered by Smith and Palmer with alloys of around 20 pct iron, it was decided to make a rather complete investigation 0f this type of alloy. As a result 0f this investigation, a method of alloying and fabricating copper alloys containing 10 to 15 pct iron was developed

Jan 1, 1948

By Robert Pike

THE first authentic description of an iron bath for the deposition of iron is probably that of Bottger in 1846, who used a bath containing ferrous sulfate and ammonium chloride. In 1861, Kramer deposited iron from ferrous chloride solution. Electrolytic iron was produced in 1.869 by Bietz, who used it for making some magnetic tests. In the same year, Klein is said to have worked out his process. Jacobi1 in 1869 described the results obtained in electroplating with iron on copper for making dies and plates for bank notes, by Klein&apos;s process. A letter from Klein to Jacobi describes the bath more fully. It consisted of FeSO4 + (NH4)2S04. Lenz2 described ?some properties of electrolytically precipitated iron. He used Klein&apos;s bath, FeSO4 + MgSO4 + MgCO3, to neutralize and obtained fine-grained and hard iron. His conclusions were as follows: 1. Electrolytic iron and copper contain gases, notably hydrogen. 2. The volume of gas absorbed by iron varies within wide limits, but it is easy for iron to take up very considerable quantities of gas. 3. The absorption of gas is principally in the first formed layers of iron. 4. When iron is heated, gas begins to come off below 100°, principally hydrogen. 5. Heated to redness, reduced iron oxidizes in water, in part at least at the expense of the oxygen of the water, decomposing it and setting free hydrogen, which is partly or wholly absorbed. Siemens,3 in 1889, was the first to propose a general process embodying a step for leaching a sulfide mineral with ferric chloride or sulfate and a step for regenerating the leach and depositing iron on a cathode in a diaphragm cell. So far as is known, Siemens did not carry out his patent

Jan 1, 1930

By O. M. Schaus

GRATIFYING progress continues towards the elimination of the hazards confronting health and safety in and about mines. Employers and employees are diligently co-operating. One of the outstanding movements towards this end is the National Safety Competition conducted by the U. S. Bureau of Mines. William W. Adams, of the Bureau, has stated that "Through 1936 there has passed by a dozen years of this National Safety Competition, as it started in 1925 with an enrollment of 210 mines and quarries in 28 states and 68 million man-hours of employment. For 1936 it covered 328 mines and quar-

Jan 1, 1938