Search Documents

J. Chipman (Massachusetts Institute of Technology, Cambridge, Mass.)—The fact that the experimental work has been applied to copper rather than iron and that the paper is presented to the Iron and Steel Division, I regard as rather significant. It shows the unity of metallurgy and the fallacy of trying to cut it up by metals. This result for the solubility of sulphur in molten copper correlates with Professor Schuhmann's finding that the published data on the other side of the copper-sulphur miscibility gap are also in error. I should like to ask the author to say a little bit more about the sulphur capacity of the slag. T. Rosenqvist (author's reply)-—I hope that Dr. Chipman will find the derivation of the expression for sulphur capacity more clearly explained in the printed version of the paper than in the oral discussion at the meeting. I feel that this quantity, which actually is the ratio of two activities, can be measured more easily than the individual activities. Even if the ratio CaO/CaS is chosen as the standard state, the expression can be used for any slag, even for slags completely free of lime, and it represents a way to put the desulphurizing power of all slag constituents into one bag. Some doubt has been expressed as to whether oxygen ions really exist in calcium oxide and in molten slags. From a thermodynamic view point that question is of minor importance. The term oxygen ion activity, or any activity for that matter, is defined rigorously by the equation: activity = exp u/RT, where u is the change in free energy connected with the transfer of one mol of ions from the standard state into the slag. Whatever happens to the ion in the slag is of no concern to the thermodynamicist. Regardless of whether the ion is "free" in the slag or not, or whether it is present in a very small amount, its activity can always be expressed, and for a thermo- dynamic calculation that is all we need. However, ionic activities will only be of some real value if they are simple functions of the slag composition, or can be measured easily. Concerning the real nature of the oxygen in the slag, my feeling is that the oxygen atom has a rather multiplex nature depending on how strongly it is tied by covalent forces or polarized by the other atoms or ions present. The oxides of iron, cobalt, and nickel differ from calcium oxide and blast furnace slags as to the amount of free electrons that can give rise to electronic conductivity. In slags we know that the conductivity is mostly ionic. The fact that reversible emf's can be obtained with oxygen electrodes in certain salt melts, indicates a significant amount of oxygen ions in these melts. But extended work, e.g. polaragraphic studies and measurements of transference number; are needed to obtain quantitative information about the real structure of the slags. D. E. Babcock (Republic Steel Corp., Youngstown, Ohio)—-With reference to the ion, it might be well to remember Dr. Moses Gomberg. All of his life he had no use for the ionization theory and he contributed greatly to the field of chemistry on the assumption there was no such thing as ions. I do not think we have to worry about whether the oxygen is ionic or not. I think one thing specifically should be brought to your attention and this I think is one of the important contributions of Dr. Rosenqvist. He pointed out what we know as oxygen potentials or what is described as oxygen potentials. I have used this concept for a long period of time and I want to state that if this concept is properly applied, it vitiates much of what we have in the literature, or makes our usual ideas regarding oxidation seem primitive. That one thing is more valuable than almost all the rest of the discussion as a fundamental basis on which to build a reasonable in-

Jan 1, 1952

By Terkel Rosenqvist

J. Chipman (Massachusetts Institute of Technology, Cambridge, Mass.)—The fact that the experimental work has been applied to copper rather than iron and that the paper is presented to the Iron and Steel Division, I regard as rather significant. It shows the unity of metallurgy and the fallacy of trying to cut it up by metals. This result for the solubility of sulphur in molten copper correlates with Professor Schuhmann's finding that the published data on the other side of the copper-sulphur miscibility gap are also in error. I should like to ask the author to say a little bit more about the sulphur capacity of the slag. T. Rosenqvist (author's reply)-—I hope that Dr. Chipman will find the derivation of the expression for sulphur capacity more clearly explained in the printed version of the paper than in the oral discussion at the meeting. I feel that this quantity, which actually is the ratio of two activities, can be measured more easily than the individual activities. Even if the ratio CaO/CaS is chosen as the standard state, the expression can be used for any slag, even for slags completely free of lime, and it represents a way to put the desulphurizing power of all slag constituents into one bag. Some doubt has been expressed as to whether oxygen ions really exist in calcium oxide and in molten slags. From a thermodynamic view point that question is of minor importance. The term oxygen ion activity, or any activity for that matter, is defined rigorously by the equation: activity = exp p/RT, where p is the change in free energy connected with the transfer of one mol of ions from the standard state into the slag. Whatever happens to the ion in the slag is of no concern to the thermodynamicist. Regardless of whether the ion is "free" in the slag or not, or whether it is present in a very small amount, its activity can always be expressed, and for a thermo- dynamic calculation that is all we need. However, ionic activities will only be of some real value if they are simple functions of the slag composition, or can be measured easily. Concerning the real nature of the oxygen in the slag, my feeling is that the oxygen atom has a rather multiplex nature depending on how strongly it is tied by covalent forces or polarized by the other atoms or ions present. The oxides of iron, cobalt, and nickel differ from calcium oxide and blast furnace slags as to the amount of free electrons that can give rise to electronic conductivity. In slags we know that the conductivity is mostly ionic. The fact that reversible emf's can be obtained with oxygen electrodes in certain salt melts, indicates a significant amount of oxygen ions in these melts. But extended work, e.g. polaragraphic studies and measurements of transference number; are needed to obtain quantitative information about the real structure of the slags. D. E. Babcock (Republic Steel Corp., Youngstown, Ohio)—-With reference to the ion, it might be well to remember Dr. Moses Gomberg. All of his life he had no use for the ionization theory and he contributed greatly to the field of chemistry on the assumption there was no such thing as ions. I do not think we have to worry about whether the oxygen is ionic or not. I think one thing specifically should be brought to your attention and this I think is one of the important contributions of Dr. Rosenqvist. He pointed out what we know as oxygen potentials or what is described as oxygen potentials. I have used this concept for a long period of time and I want to state that if this concept is properly applied, it vitiates much of what we have in the literature, or makes our usual ideas regarding oxidation seem primitive. That one thing is more valuable than almost all the rest of the discussion as a fundamental basis on which to build a reasonable in-

Jan 1, 1952

By M. C. Flemings, T. Z. Kattamis

Dendrite morphology and grain size were studied in bulk samples of iron and nickel base alloys under-cooled up to 300°C. In the alloys studied, dendrite morphology gradually changes with increasing undercooling from the usual dendritic structure to a structure composed of cylindrical dendrite arms. At a critical undercooling of approximately 170°C in these alloys there is an abrupt transition to a fine-grained structure of spherical morphology. Final dendrite-arnz spacing of melts nucleated at less than the critical undercooling decreases with increasing undercooling and with decreasing distance from a chilled surface. Grain size of melts nucleated at greater than the critical undercooling decreases similarly with these factors. It is concluded that structure coarsening, with reduction of surface area as driving force, is the principal mechanism determining final dendrite-arm spacing in melts nucleated at small undercoolings and grain site in melts nucleated at large undercoolings. IN solidification of highly undercooled melts, nuclea-tion and growth of the solid is accompanied by a rapid release of latent heat of fusion. The heat release is sufficiently rapid in bulk specimens that it takes place essentially adiabatically with respect to the surroundings; hence the specimen heats up ("recalesces") to some maximum recalescence temperature. For bulk liquid metals and alloys, a simple thermal balance shows the undercoolings obtainable in bulk samples are not sufficient to lower the maximum recalescence temperature below the equilibrium solidus temperature. Hence, some liquid always remains at the end of recalescence; this liquid must solidify by rejection of heat to the surroundings. Metals, including iron and nickel base alloys, normally freeze with only a few degrees of undercooling. In general, nucleation begins on impurity particles present in the metal, at a "heterogeneous nucleation temperature" that is quite close to the equilibrium liquidus temperature. Very small droplets of metal can be undercooled considerably before nucleation occurs,1-4 presumably because subdivision of the liquid reduces the probability of solid impurity in a given droplet. Following early work on metal droplets,' a series of studies has shown that it is possible, without great difficulty, to undercool bulk samples of many metals and alloys. Undercoolings obtainable are approximately two tenths of the melting point for nickel, iron, copper, and other metals and alloys.5-9 Specimen sizes have generally been in the range of 50 to 500 g. Studies on undercooling to date have been concerned primarily with techniques of undercooling and with nucleation and growth kinetics. Only limited consideration has been given to dendrite morphology in under- cooled alloys. One such study, in bulk Cu-Ni alloy,8 showed that at small undercoolings a typical dendritic structure was obtained. At undercoolings the order of 175°C the structure of a Cu-40 pct Ni alloy became "ray or starlike", and a dense network of subbound-aries appeared. At still larger degrees of undercooling, of the order of 250°C, the structure became more random and included an ensemble of globular forms. Comparable results were obtained by walker10 on Cu-Ni alloys, and by Kamenetskaya et al.11 in research on Cu-Ni, Sb-Bi, Fe-Ni, and Fe-Cr alloys. In this work, study was made of the processing parameters influencing dendrite morphology and grain size in undercooled alloy melts. Experiments were specifically designed to show the effects of coarsening ("ripening") during solidification on final casting morphology. EXPERIMENTAL PROCEDURE Apparatus used was patterned after that of Walker,10 Fig. l(a). Melting was by induction under reduced pressure of helium. Two different types of crucible materials were used; there was no difficulty in obtaining substantial undercooling in both types of materials. Alumina crucibles were used for the bulk of the runs made, with a glass coating separating the metal from the crucible walls. Other runs were made using fused silica crucibles with or without slag coating. A graphite susceptor was employed around the crucible to aid in melting and to reduce melt stirring. The major portion of the experimental work was on

Jan 1, 1967

In reply to inquiries and comments which have reached me since the publication of this paper, and in explanation of some seeming discrepancies between my statements in the text concerning the amount of displacement of the faults, on one hand, and certain figures in the plates on the other hand, I give here, with some additional remarks, my measurements of the displacements in the different sections, which it originally seemed unnecessary to print : By displacement, I mean neither the throw, i.e., the vertical distance apart of the two edges of a faulted bed (what Mr.

Jan 1, 1896

By E. S. Machlin, Morris Cohen

The martensite reaction in single crystals and polycrystals of 70 pct Fe-30 pct Ni alloys is shown to be autocatalytic in nature, producing bursts of transformation during cooling. The temperature of the first burst of transformation, called Mb, occurs below M, in these alloys. Experiments were devised to test the athermal embryo and strain embryo theories of martensite nucleation. The results indicate that internal strains, either within the virgin austenite or around existing martensitic plates, control the nucleation process in these alloys. Furthermore, the growth of martensitic plates is not limited by the attainment of an elastic balance with the austenitic matrix, but by the occurrence of plastic deformation at the martensite boundaries which interferes with the propagation mechanism. IN an investigation of the martensitic habit in single crystals of a 69 pct Fe-31 pct Ni alloy,' it was observed that about 25 pct of the austenite transformed during subatmospheric cooling within the time-interval of an audible click. This event proved quite spectacular: The shock wave sent out from the specimen freely suspended on a thread in the refrigerating liquid was occasionally sufficiently intense to shatter the Dewar container and to separate the toluene column in the immersed thermometer. The Present investigation was undertaken to determine- the kinetics and mechanism of this "burst" type of martensitic reaction. The analyses of the alloys studied are given in Table I. The composition of the single crystal specimens is designated by alloy A, while the polycrystal-line specimens were made of alloys B and C as noted in the text. The single crystals were prepared in a vacuum furnace, using a modified Bridgman technique. Most of these crystals were homogenized by holding for 24 hr at about 1300°C just after solidification. However, it may be emphasized here that the degree of homogenization was not a controlling factor in the subsequent experiments, inasmuch as specimens having different degrees of homogenization yielded the same results. All of the single crystals were fully austenitic as slowly cooled to room temperature. An illustration of the burst phenomenon is given in Fig. 1, which shows oscillograms of electrical resistivity and temperature vs. time during the continuous quenching of 1/16 in. wire specimens (alloy B) in a dry ice and acetone bath at —77°C. There are at least two observable bursts in this case, as indicated by the sharp decreases of resistance accompanying the sudden formation of substantial quantities of martensite. The thermal arrest during the quench probably corresponds to the larger burst. Usually the bursts are followed by more or less progressive transformation during continuous cooling. It will also be noted that the resistance continues to decrease after the specimen has reached the bath temperature. This isothermal change denotes the formation of martensite at constant temperature, and will be the subject of another paper. Examination of fiducial scratches on the surface of a transformed single crystal has shown2 that the scratches in adjoining nonparallel martensitic plates are usually bent in opposite directions, as though one plate forms in such a way as to relieve the matrix stresses set up by the adjacent plate. This, together with some of the results described in ref. 1, Table I. Compositions of Alloys Studied, in Percent Alloy Ni C N Mn Si P S Cr A 31±0.3 0.048 0.027 0.003 0.56 0.007 0.002 B 29.5±0.2 0.036 0.02 0.19 0.09 0.008 0.006 C 19.99 0.52 0.37 0.47 0.010 0.015 0.04 led to the tentative concept that a cooperative action exists which provides the impetus for much of the transformation that appears during the burst. The following series of experiments were performed in order to test this idea. Cooperative Nature of the Burst Two adjacent disks, Va in. thick x % in. diam, were cut from a single austenite crystal of alloy A using a jeweler's saw. One of the disks was then cut into 15 parts. Then 12 of the latter pieces and the second disk were austenitized (stress relieved) at 600°C for 30 min and water quenched to room temperature. The temperatures at which the first burst of transformation appeared were determined for

Jan 1, 1952

By N. Albon, J. F. Miller, R. W. Coutant

The deposition of nickel from nickel carbonyl onto amorphous substrates has been studied, with attention being paid to the specific effects of the physical and chemical nature of the substrate and to the effect of oxygen on the crystal morphology. With substrates having microscratches or etch lines, nu-cleation was observed to occur preferentially at these surface features. Flame polishing of the substrate surfaces was found to remove any regularity in preferred nucleation sites. Nucleation was observed to occur less readily on substrates having relatively low surface energies, e.g., Teflon and carbon, than on materials having relatively high surface energies such as fused silica. At low oxygen concentrations [Ni(CO)4/O2 > 54 x 1031, apparently pure and well-formed nickel crystals were observed to nucleate and grow irrespective of the presence of oxygen. At higher concentrations of oxygen, a secondary growth process, dependent upon oxygen concentration and resulting in a gradual change in crystal morphology, was observed. It is concluded that the influence of oxygen on the nucleation and growth of nickel is determined by the relative kinetics of the various possible reactions, and that under the experimental conditions employed the 0-Ni interaction occurs at some nucleation or prenuclea-tion stage. THE purpose of the research on crystal nucleation in chemical vapor deposition as described in this paper has been twofold: 1) to examine some effects arising from the use of amorphous substrates, and 2) to study the specific effects of oxygen on the nucleation and growth of nickel in a nickel carbonyl-carbon monoxide system. The nickel-nickel carbonyl system was chosen for study for several reasons: 1) nickel films are of potential interest in electronic technology, and 2) the deposition can be carried out at moderate temperatures, thus making possible detailed study of the processes occurring and the use of a variety of substrate materials (including some which melt at relatively low temperatures). Fairly well-characterized chemical kinetics and a broad background of information are available on the py-rolysis reactions and on the mechanisms of Ni-O interactions. NUCLEATION AND GROWTH THEORY The theoretical background for the analysis of nucleation and growth by vapor deposition for a one-component system (physical vapor deposition) and the problems encountered therein have been reviewed by Hirth and pound.' More recently Mande12 has indicated the difficulties of applying such theory to chemical systems. One of the major problems involved is the possible multiplicity of chemical reactions and deposition routes. For example, those reactions which are probably of significance in a discussion of the pyrolytic deposition of nickel from nickel carbonyl under the conditions of the present experimental work are illustrated in Fig. 1. As is true with most cases of chemical deposition, many of the quantitative data necessary for a complete analysis of the system are either not available or not directly measurable. However, with the present system, sufficient data are available for a discussion of nucleation and growth on a qualitative basis. Classically, the rate of nucleation of a monatomic species being deposited from a vapor phase is given by

Jan 1, 1965

By C. R. Johnson, R. A. Greenkorn, R. E. Haring

Three confined five-spot miscible displacements at unity, favorable, and unfavorable mobility ratios were conducted in a shallow, water-saturated sandstone of Pennsylvan-ian age near Chandler, Okla. These studies, plus associated laboratory experiments, were designed to measure miscible displacement performance in a controlled natural system, using known scaling criteria to develop an approach to modeling the heterogeneous field system. We have concluded from these studies that: (I) displacement efficiency in the field is a pronounced function of mobility ratio, indicating that miscible fingering observed in simple laboratory models occurs in the field: (2) field displacements can be quantitatively predicted by scaled laboratory models if the degree and location of field permeability variations are preserved in the models: and (3) arbitrary simplifications of heterogeneity will not necessarily predict observed displacement efficiency, and the simpler the model, the more optimistic the prediction. INTRODUCTION Many processes to achieve miscible displacement of reservoir oil by injected fluids have been conceived and field tested by the oil industry. Among the better known are high-pressure gas, enriched gas, and LPG banks. The simplest form of miscible displacement—one fluid miscibly displacing another fluid of different viscosity but the same density—has been studied extensively in homogeneous laboratory models. Observations of unstable fingering have been made which explain the significant decrease in displacement efficiency as the mobility ratio (ratio of displacing fluid mobility to displaced fluid mobility) increases. General industry experience with field tests of miscible displacement projects, mostly LPG banks, has been premature solvent breakthrough and lower than predicted production rate increases. These results have been attributed to either unstable fingering, unusual or unexpected permeability stratification, or both. Miscible displacement data in a controlled natural system have never been reported, however. Also, it has not been shown that properly designed and constructed laboratory models quantitatively predict field-scale behavior. The purpose of the combined field and laboratory ex- periments reported in this paper is twofold. The first was to measure miscible displacement performance at different mobility ratios in natural rock approaching field size under precise, controlled conditions. The second purpose was to utilize known scaling criteria plus several approaches to heterogeneity to model the field. Comparison of model and actual field results should then determine whether or not the laboratory phenomena (manifested by miscible displacement efficiency) are exhibited in large, natural rock systems. We carried out our program by first locating a shallow, water-saturated reservoir whose rock properties were representative of oil-bearing reservoirs. Detailed reservoir description by core analysis and interference testing showed the field site to be heterogeneous. A sequence of controlled, aqueous-phase miscible displacements was conducted at unity, favorable and unfavorable mobility ratios. A central, confined pattern was used to obtain the displacement data. A laboratory program using sand-packed models was conducted to determine the modeling criteria necessary to simulate field behavior of miscible displacement in a heterogeneous system. SCALING THEORY The detailed derivations and descriptions of the scaling laws that apply to laboratory models of reservoirs are adequately described elsewhere, so the following discussion will be restricted to facets of importance in this study. For a displacement in which one liquid miscibly displaces another, the following dimensionless groups are required to have the same numerical value in the model as in the field: The model also must be geometrically similar to the field, be spatially oriented the same as the field (same dip angle), and have the same initial and boundary conditions as the field (same initial fluid saturations and same injection-production well arrangement). When these conditions are satisfied, the theory predicts that at dny dimensionless time (pore volumes of produced fluids) the dimen-sionless flow potential and dimensionless fluid concentrations will be identical at all dimensionless spatial locations within the model and the field. If this prediction is correct, then the local dimensionless velocities must be identical, thus the instantaneous fraction of displaced fluid produced and the cumulative recovery expressed as fraction of original fluids in place must be identical at all dimensionless times. The theory outlined above has been obtained by either dimensional analysis or inspectional analysis of differential

Jan 1, 1966

R. S. Shoemaker: Our first question is, is there a need for a grizzly before a primary crusher? What is its effect on crusher capacity and crusher maintenance? Is it worth the extra capital cost in a crusher installation? Vincent: ASARCO has a grizzly at Mission. Utah Copper uses grizzlies ahead of their gyratories. There is some quite abrasive ore at Mission, an argillite type of rock, which has a work index of 16.5 to 20, which is getting up toward the taconite classification. We get a life of 12- 16 million tons per set of concaves or per mantle with the grizzly ahead of the crusher. At Duval Corp., some 6 miles to the south of Mission, their crusher installation on a good, hard rock does not have a grizzly, and the last information I had is they get a life of about 2 ½ -3 million tons on their mantle and concave. At Silver Bell, our other copper unit in Arizona, they do not have a grizzly ahead of the gyratory and there they get a life of about 5-6 million tons. At Utah Copper, which we all know is a fairly soft ore, relatively speaking, they get a life of 24-27 million tons with grizzlies ahead of the crushers. I think a grizzly has a very definite effect on the life of the mantle and the concaves. As far as a jaw crusher is concerned, I think that usually it is desirable to have a grizzly if it is properly designed, which means it is self- cleaning. Otherwise I would not like to see one in the circuit.

Jan 9, 1967

By W. P. Blake

The mining district and the town of Tombstone are situated in Cochise County, Arizona Territory, at the northwest end of the Mule Pass range of mountains, in longitude 110°, and latitude about 31 40' N,, upon the right bank of the San Pedro River, from which the town is distant 9 miles east.. It is also 24 miles south of Benson station on the Southern Pacific Railroad of Arizona, and about 40 miles north of the Mexican line. Its altitude above the sen is 4600 feet. The Dragoon Mountains rise across a valley to the northeast, and the Huachuca Range similarly upon the southwest. The country is open, without timber, and the surface, where the mines are opened, is in general gently rolling, and accessible to wagons by. natural roads. The first locations were made in the pear 1878 by the Scheffelin brothers and Richard Gird, the latter being well known among the pioneers of Arizona as a surveyor and miner, who contributed largely to our knowledge of the geography of the Territory in early days,

Jan 1, 1882

By I. A. Goddard

INTRODUCTION This paper deals with the development of the sublevel open stoping (SLOS) method in lead orebodies at the Isa Mine of Mount Isa Mines Limited, during the last ten years. Open stoping in different forms has been used at the Isa Mine for many years. Prior to the period under review, stopes were small, pillars were not always recovered, and scrapers extracted the ore. By the end of the sixties, the use of load-haul-dump units was becoming more widespread. Wagner ST5's were the mucking units for the lead cut and fill stopes. Some of the open stopes in 5 orebody above 13 level had 100 kW slushers, but the more southerly stopes were the sites for the introduction of diesel front-end loaders for extraction. In the early seventies, new methods were used in the block of six stopes in 2 and 5 orebodies between 8 level and 13 level and a trial stoping project was undertaken in 7 orebody between 11 level and 13 level to determine possible stope dimensions for the extraction of the Racecourse orebodies below 13 level. By the mid-19701s, stoping was well underway in 5, 7 and 8 orebodies between 13 level and 15 level, using the 'triplet' system, incorporating cemented hydraulic fill to allow greater pillar recovery. As the eighties were entered, development of the Racecourse orebodies below 15 level commenced, as did preparations for 1 orebody in the upper levels of the north end of the mine. In both cases, the pillar recovery method has been changed to reduce the amount of cemented fill required for pillar recovery. GEOLOGY Most of the lead orebodies at Isa Mine lie chiefly to the north of the central shaft complex. They are bedded sulphide deposits in a host rock called Urquhart Shale, which dips at roughly 650 to the west. The main minerals are galena and sphalerite, with the silver mineral, freibergite, being contained in the galena. To the hangingwall of the sequence are the Black Star orebodies (1, 2 and 5) which are relatively wide, pyritic and with low to above average grade lead. The Racecourse orebodies (6 to 16) lie to the footwall, and have a large variation in width, low to high grade lead, and gradation in the lead to zinc ratio from north to south. Stope outlines are often determined by economic or engineering considerations rather than geological. The published extraction reserves are 56 million tonnes of primary ore, containing 150 grams of silver per tonne, 6.4% lead and 6.5% zinc. Traditionally, it has been regarded as lead ore, although the dominant revenue earner varies from time to time. In the Black Star orebodies, the ore and hangingwalls are more competent and open stoping has long been used. The major Racecourse orebodies which have been open stoped are 7 and 8 orebodies. This has been where the orebodies are wider (to the south) and where hangingwall conditions allow. This latter aspect has been greatly influenced by the presence of 'silica dolomite1. This tough, relatively homogeneous, non-bedded rock is, in fact, the host rock for the copper mineralisation at Mount Isa, and provides a competent hangingwall for some of the lead stopes. While the shale's bedding and jointing has a major influence on the ground conditions, there is a major fault system which causes local problems. The principal virgin stress direction is perpendicular to the bedding, but the local stress situation is complicated because of shielding by filled stopes in the hangingwall copper orebodies and because of the interaction between orebodies being extracted to the footwall. Most development on strike is mined with a 'shanty-back’, with the back being as close to normal to the bedding as possible. This is near parallel to most jointing and the principal stress direction. Figure 1 is a plan view of 14 level north, which provides a representative horizontal section through the orebodies. A typical cross section is shown in Figure 2. The narrow, parallel footwall orebodies can be seen to differ from the wider hangingwall orebodies.

Jan 1, 1981

By R. E. Carter, F. D. Richardson

Self-diffusion coefficients have been measured for iron in wustite (700° to 1000°C) and for cobalt in cobaltous oxide (800&apos; to 1350°C) by means of radio-isotopes. Both sectioning and decrease of surface-activity methods have been used and a particular shortcoming of the latter method has been disclosed for wustite. The effects of oxygen pressure on the composition of cobaltous oxide and on the diffusion coefficient of cobalt in the oxide have been established. The effect of the preparation conditions of the cobalt-oxide specimens on the diffusion measurements has been determined. It has been concluded that diffusion of cobalt occurs via vacant cation sites and that a cobaltous-oxide disk reaches equilibrium with its environment in a time which is very short compared with that needed for diffusion of the radio-isotope. THE availability of radioactive isotopes in recent years has permitted the measurement of many self-diffusion coefficients which were hitherto impossible to determine. With the advent of radioactivity, the method of measuring diffusion coefficients has also changed. The earlier sectioning method by which the concentration profile of the diffusing species was determined in the diffusion specimen has often been rejected in favor of the decrease of surface-activity method first developed by Von Hevesy,&apos; and extended by Steigman, Shockley, and Nix,&apos; and Raynor, Thomassen, and Rouse." With the experimental arrangement where an infinitely thin deposit of tracer is diffused into a semi-infinite cylinder, the decrease in activity of the active face due to diffusion of the tracer into the specimen is measured by counting the active face before and after diffusion. Under these conditions, the appropriate solution of the diffusion equation is R = e*(l-<K/Z) [1] where R is the ratio of the counting rates after-to-before diffusion, $& is the Gaussian error integral of \/Z, and Z is defined as Z = p2Dt, p being the linear-absorption coefficient of the detected radiation in the diffusion specimen, D the self-diffusion coefficient, and t the diffusion time. In the older sectioning method the concentration distribution of the tracer is found after diffusion by analysing thin parallel sections cut from the active face of the diffusion specimen. As seen from the solution of Fick&apos;s second law for the distribution of an infinitely thin source after diffusion into a semi-infinite cylinder the log of the concentration plotted against x&apos; will be a straight line of slope log e/4 Dt. The diffusion coefficient thus can be calculated directly. The units of the tracer concentration are completely arbitrary, since any change in units does not change the slope of the log c vs x2 lot. Although both of the above methods have been widely used, a thorough experimental comparison does not appear to have been made. Birchenall and Mehl,&apos; during an investigation of the self-diffusion rate of a and r iron by the surface method using Fe" tracer, diffused and sectioned one welded couple. The diffusion coefficient from this run agreed with those by the surface method. Buffington, Bakalar, and Cohen," during an investigation on a and y iron

Jan 1, 1955

By L. S. Castleman, L. L. Seigle

IN a recently reported investigation, J. B. Clark and F. N. Rhines1 used a diffusion couple technique to determine the number of intermetallic phases which should be present in the Al-Mg equilibrium phase diagram. Their method was an application of the following generally accepted principle. If a diffusion couple made up of two metals is annealed at a given temperature for a long time, all the phases of the binary system which exist under equilibrium conditions at the diffusion temperature will form intermetallic layers. It is important that the diffusion temperature be high enough and the diffusion time be long enough to permit the nuclea-tion of all thermodynamically stable phases at the interface of the couples and their growth to observable thicknesses. These simple time-temperature criteria are at times difficult to satisfy, and it is the purpose of this note to point out a situation in which this is the case. The authors are currently studying diffusion bonding in the Al-Ni system." It is well established

Jan 1, 1958

By Robert Hunt

(New York Meeting, February, 1913.) I HAVE frequently stated that while the chemical composition of steel is important, yet even greater importance is connected with the mechanical and heat treatment of the metal. During the past year I encountered such a positive example of that fact that I deem it worth putting upon record. A prominent railway system divided an order for open-hearth steel rails between two steel works, both of which are under the control of the one corporation; giving to one about 18,000 tons, and to the other 7,500 tons of the same section and to be made under the same specifications. The rolling results obtained in the two mills varied so widely that a study of the figures is intensely interesting and serves to illustrate the advantages obtained by careful ingot casting, and, quite as pertinently, the possible benefits of careful subsequent heating and rolling with moderate reductions in the rolling process. The smaller order was rolled complete in four installments during the same months that the larger order was being made in six separate installments; but, to permit of exact comparisons, the totals of the four installments (completing the order with the mill which I will call A) are given with the totals of the first four installments of the larger order, made by the mill designated as B. These rolling results are:

Jan 5, 1913

By J. J. Frawley, W. J. Childs

Experiments were carried out to induce grain refinement during solidification by applying vibrational energy (freq 20 kc) to small specimens of bismuth, tin, and bismuth-tin alloys. The results show that if the intensity of the applied sound -field is not great enough to fragment the growing dendrites of a pure metal, no grain refinement is observed and the pain size of the dynamically nucleated specimens is the same as the grain size of a specimen statically supercooled the same amount. Bismuth specimens did not show any grain refinement; whereas, the tin specimens did show grain refinement. This phenomenon is the result of the difference in growth habit between the bismuth and tin dendrites. The bismuth-tin alloys showed grain refinement and, in addition, the segregation pattern was changed. THE solidification process is a change in phase requiring the nucleation of the solid phase from the liquid and the growth of this solid phase at the expense of the liquid phase. Since many physical properties and also the integrity of a casting are dependent on the solidification process, understanding and controlling this process are very important.&apos; A good example in the controlling of a cast structure using heterogeneous nucleation theory is the reduction of grain size in aluminum castings by nucleation catalysis.2 This mechanism of nucleation catalysis has been explained by Turnbull.3 Another technique for grain refinement, which has received much attention but the mechanism has not been fully understood, is to vibrate the solidifying melt. Vibrations can be applied to the melt either by vibrating the mold directly or by introducing a vibrating rod into the melt.4-13 Three mechanisms have been proposed to explain this phenomenon: 1) The mechanical fragmentation of the original dendrites that grew into the melt. These crystals or fragmented dendrites act as new growth sites. 2) The nucleation of new grains in the liquid by the generation of very high pressure pulses caused by cavitation in the liquid. 3) The remelting of the dendrite arms during the solidification process. This mechanism is operative only in alloy systems and would be enhanced by stirring or mechanical vibration. The purpose of this investigation was to determine the mechanism that will increase the number of grains when mechanical energy is introduced into a solidifying melt. APPARATUS The unit used to generate the ultrasonic vibrations was manufactured by the Redford Co., and is similar to the one used in ultrasonic soldering. Fig. 1 is a sketch of the major components used for generating ultrasonic vibrations. The crystal transducer assembly consisted of four lead zirconate ti-tanate piezoelectric crystals in an aluminum holder. An acoustical horn, which was fabricated from stainless steel, was attached to the holder by a set screw. The resonant frequency of this unit was 20,000 cycles per sec. A Pyrex crucible, 4 in. in diam and 4 in. high, was contained in a hole in the top of the horn. The piezoelectric crystals changed volume when excited by an electric signal, thereby generating a sound signal which passed through the horn. The crucible was coupled to the horn by a liquid silicone oil. The purpose of the couplant was to transmit the soundwaves from the horn to the crucible. Without the couplant, much of the sound energy would be lost. The energy transmitted was sufficient at the resonant frequency used, so that acoustical cavitation always occurred in the molten metal. The presence of acoustical cavitation was detected by the characteristic hissing sound emitted from the liquid. EXPERIMENTAL PROCEDURE The influence of ultrasonic vibration on the grain refinement of bismuth, tin, and bismuth-tin alloys was studied. These metals were chosen because of their low melting temperature and the relative ease with which they can be thermally supercooled. The following procedure was used for obtaining large amounts of supercooling. Pure bismuth (99.999+), which was received in bar form, was mechanically broken into pieces small enough to be accommodated in a 50 ml beaker. About 200 to 300 g of bismuth and a few grams of SnCl2 as a flux were placed in the 50 ml beaker and melted by induction heating. The melt was held for 20 min at

Jan 1, 1970

By G. E. Burpee

A COMPREHENSIVE study of insoluble residues in the productive Permian limestone in the Hobbs and Eunice fields, Lea County, N. M., has been conducted by Shell Petroleum Corp. engineers {luring the past two years. This study was prompted by the belief that the stratigraphy of the producing formation might be worked out in detail and that some relationship might be established between the permeable oil, gas, and water zones and correlatable lithologic horizons within the productive formation. As a result of the study, correlations have been established which have proved of great value to both an orderly development and corrective program.

Jan 1, 1935

By P. C. Badgley

The purpose of this paper is to demonstrate the usefulness of systematic analyses of weakness patterns. The term weakness here includes structural features such as fractures, foliation planes, lineaments and bedding. Many of these features are mapped by geologists in the field, but analysis of the field date is frequently overlooked. Examples are presented to show the value of such studies in petroleum and mineral exploration, in dam site selection, and in regional tectonic interpretations. Numerous theories have been presented to account for the mechanics and time of origin of fracturing. This is an extensive subject and cannot be reviewed in detail here. The reader may wish to refer to other papers.*"5 It is sufficient to say that most fracture patterns can be related to one or more of the following force mechanisms: compression, tension, torsion and fatigue (inheritance by upward propagation of pre-existing fractures). Fractures generally occur in sets in a district. The angular relationships and other characteristics of the individual sets frequently help in determining the force mechanism and movement history of the deformation. From a geometric point of view fractures are commonly referred to as longitudinal, cross, or diagonal (shear), depending upon their orientation relative to other major structural features such as anticlinal axes and so forth. These terms will be used from time to time and are illustrated schematically in Fig. 1. FIELD PROCEDURE AND TREATMENT OF DATA In fracture studies it is very important to collect adequate field data. Fig. 2 illustrates a notebook sheet for recording significant field observations in sedimentary rocks. Slight adaptations have to be made for igneous and metamorphic terrains. Fracture density and persistence are very important factors in petroleum exploration for fractured reservoirs and mineral exploration. The density for each joint set is recorded in terms of number of joints per linear yard. The total number of joints at any one

Jan 1, 1962

Sec. 1. This Division shall be known as the Institute of Metals Division of the American Institute of Mining and Metallurgical Engineers. Sec. 2. The object of the Division shall be to furnish a medium of cooperation between those interested in the metallurgy, fabrication and uses of the nonferrous metals and their alloys; to represent the A. I. M. E. in so far as nonferrous metallurgy is concerned, within the rights given in A. I. M. E. By-law XI., Sec. 1, and not inconsistent with the Constitution and By-laws of the A. I. M. E.; to hold meetings for social intercourse and the discussion of nonferrous metallurgy; to stimulate the writing, presentation and discussion of papers of high quality on nonferrous metallurgy; to reject or accept such papers for presentation before meetings of the Division. Article II—MembeRs Sec. 1. Any Member, Associate, or Junior Associate of the A. I. M. E. in good standing may become a Member, Associate or Junior Associate of this Division upon registering in writing a desire so to do, but without additional dues. Sec. 2. But no one who has been continuously indebted to the A. I. M. E. or to this Division for more than three months shall be entitled to vote or to receive publications to which, as a member of the Division, he would be entitled. Article III—Funds Sec. 1. The expenditure of the funds reccived by the Division shall be authorized by the Executive Committee of the Division. Article IV—Meetings Sec. 1. The Division shall meet at the same time and place as the annual meeting of the A. I. M. E., and at such other times and places as may be determined by the Executive Committee subject to the approval of the Board of Directors of the A. I. M. E. Sec. 2. The annual business meeting for election of officers shall be held within a few days before or after the annual business meeting of the A. I. M. E. Sec. 3. At any meeting of the Division for which notice has been sent to the members of the Division through the regular mail at least one month in advance, a business meeting may be convened by order of the Executive Committee, and any routine business transacted not inconsistent with these By-laws or with the Constitution or By-laws of the A. I. M. E. Sec. 4. For the transaction of business, the presence of a quorum of not less than 25 members of the Division shall be necessary. Article V—Officers and Government Sec. 1. The officers of the Division shall consist of a Chairman, two Vice-chairInen, Secretary and Treasurer. The office of Secretary and Treasurer may be combined in one person, if desired by the Executive Committee. Sec. 2. The government of the affairs of the Division shall rest in an Executive Committee, in so far as is consistent with the By-laws of the Division and the Constitution and By-laws of the A. I. M. E. Institute of Metals Divisiori

Jan 1, 1931

Institute of Metals Division SAM TOUR, Chairman J. R. FREEMAN, JR., Vice-chairman ZAY JEFFRIES, Past-chairman C. H. MATHEWSON, Vice-chairman WILLIAM M. COHSE, Secretary-Treasurer 810 Eighteenth Street, N. W. Washington, D. C. Executive Committee Until February, 1931 Until February, 1932 Until February, 1933 T. S. FULLER J. L. CHRISTIE W. M. W.M. PEIRCE G. E. JOHNSON ARTHUR PHILLIPS A. J. PHILLIPS W. A. SCHEUCH H. M. WILLIAMS GUY C. RIDDELL Research PAUL D. MERICA, Chairman S. SKOWRONSKI Data Sheet R. S. ARCHER, Chairman T. S. FULLER J. STRADSS C. H. MATHEWSON F. L. WOLF

Jan 1, 1929

By K. Brack, G. H. Schwuttke

Annealing properties of subszerface amorphous lavers produced through high-energy ion implantation in silicon are studied. The buried layers are produced through the implantation of ions (nitrogen), ranging in energy from 1.5 to 2 mev. X-ray interference patterns, transmission electron microscopy, and resistivity profiling are used to study the annealing characteristics of the ion damage. The annealing experiments indicate a low temperature (below 700°C) and a high temperature (above 700°C) region. Significant changes occur in the amorphous layer during the high-temperature anneal. Such changes are corre-lated with the re crystallization of the amorphous silicon and the formation of subsurface (buried) silicon-nitride films. TODAY&apos;S main problems in the field of ion implantation are related to the accurate determination and prediction of 1) the distribution profiles of implanted ions, 2) the lattice sites occupied by the implanted ions, 3) the lattice damage produced through ion implantation, and 4) the annealing characteristics of damage centers in the lattice. This paper reports investigations concerned with the problems listed under 3) and 4). EXPERIMENTAL Our investigations cover the energy range of incident ions from 100 to 300 mev and from 1 to 2.5 mev. The emphasis of this study is on the energy range from 1.5 to 2 mev. The experiments are conducted with single charged nitrogen ions. To implant the ions a van de Graaff generator is used as described by Roosild et al.1 Accordingly, a gas containing the desired ion specie is passed through a thermome-chanical leak into a radio frequency activated source. The positive ions are driven into the van de Graaff with the help of a variable voltage probe. Emerging from the accelerator the ions drift into a magnetic analyzing system and here the desired ion specie is bent 90 deg into the exit port. The ion beam leaving the analyzer is defocused and drifts down a 4-ft long tube to hit the silicon target. At this position the 20 pamp ion beam has a circular cross-section of 2.1 cm. N2 is used as a source gas for nitrogen ions. The implantation target is silicon with zero dislocation density, 2 ohm-cm resistivity, (111) orientation, mechanically-chemically polished, and 1 mm thick. The target is mounted on a water-cooled heat sink and kept at room temperature. A fluence of 1015 to 1016 ions per sq cm is used. RESULTS 1) Silicon Perfection after Bombardment. High-energy ion bombardment of silicon has some striking effects on lattice perfection. Some results were reported in detail previously at the Santa Fe conference2 and are here briefly summarized for the benefit of the experiments described in the following. 1.1) Identification of Surface Films on Silicon. After bombardment all samples are found to be coated with surface films. The films on the silicon surface vary in thickness and color; they can be transparent, slightly brown, or opaque. The films are thicker and darker in the high-intensity area of the beam and they delineate the bombarded surface area of the crystal. The films produce electron diffraction patterns characteristic of carbon and of SiO2. Carbon is predominant. The presence of carbon in these films was confirmed by use of the electron microprobe. Formation of the films occurs independently of the ions used and is attributed to a contaminated vacuum of the high-voltage machine. The carbon is most likely the product of the pump oil which is cracked and polymerized under ion impact. The films stick tenaciously to the silicon surface and burn off in a low-temperature Bunsen flame. 1.2) Mechanical Perfection of the Silicon Surface. The mechanical perfection of the bombarded silicon surface was investigated through optical microscopy, electron microscopy in which the replica technique is used, and optical interferometry. No mechanical damage of the surface was visible after bombardment. However, if a bombarded sample is soaked for several minutes in hydrofluoric acid (HF), gas bubbles may develop in certain spots of the silicon surface. It is also noted that in these areas the surface film starts to peel off. Relatively large patches of film come off if the sample is soaked in HF during ultrasonic agitation. After HF treatment, pits may be present on the silicon surface. The pit dimensions are estimated to be as large as 50 µ. The pits appear in the region of most intense irradiation. 1.3) Lattice Perfection After Bombardment. No lattice damage is found on the silicon surface. Electron transmission micrographs and selected area diffraction patterns of the surface show no difference before and after bombardment. Measured approximately 2 µm down from the surface, the silicon lattice throughout this depth is of good perfection. Well-defined Laue spots and Kikuchi lines are obtained from the surface as well as from the indicated area below the surface. However, some radiation damage is dispersed in this top layer. A sharp boundary line separates this surface layer from a highly damaged layer which extends further downward into the silicon. Typical of this

Jan 1, 1970

By James H. Hance

Several years ago the writer was connected with the Mint and Assay Service of the Federal Government as Assistant Assayer at the Salt Lake Assay Office. At that time cyanide bars formed approximately half of the bullion purchased by that office. Disagreement in valuat,ion between the producer and the office was not infrequent and to a lesser extent between the Assay Office and the Mint, this latter issue being soon obviated, however, by adopting uniform methods of sampling the bars. A nice problem seemed to offer itself for research and the writer began a series of experiments which were soon terminated, however, by his going into other work, and which he regrets have not since been completed. The results attained may suggest lines of approach to this problem and are, therefore, offered in this article. Frederic P. Dewey, Assayer of the Mint Scrvice, U. 5. Treasury, has had abundant opportunity to study this phase of metallurgy, and has published several articles relative thereto.1 In the last article cited Dewey quotes analyses of cyanide bullion similar in content to that with which the writer worked, and which show some of the variations met with. In the discussion of these papers,2 comparison has been made in terms of copper bullion, but to the writer this seems of questionable value. Copper bullion may resemble silver bullion, but its similarity to gold bullion with little or no silver content is another thing. The freezing-point diagram of Roozeboom, reproduced on page 881 of the discussion cited, is for the gold-silver series as stated. The original problem under discussion, however, is not this alloy but gold with base metals other than copper. As for the statement that the corners are the worst places or

Jan 1, 1916