Search Documents

By C. O. Rison

HIGH explosives, particularly nitroglycerin, have been used in torpedoes for the purpose of shooting oil and gas wells for more than 60 years. The early history of the oil industry in Pennsylvania is not clear as to who actually torpedoed the first well, although in 1865 the Roberts Torpedo Co. procured a patent covering the process. Gunpowder was first used, although nitroglycerin was substituted shortly afterwards. Wells are shot for the purpose of increasing the flow of oil and gas A shot-hole in the producing horizon, with its contributory fissures and fractures, increases the area of and stimulates drainage into the hole. The shot-hole also acts as a collecting basin from which the oil is pumped. As a rule, hard or close-grained sands or limes are shot, other more or less porous and soft formations usually do not require shooting. and might be injured by blasting. Shooting is also resorted to in mechanical trouble such as straightening crooked holes, sidetracking pipe or tools, and for severing frozen strings of casing or drill pipe. Explosives arc also used sometimes to extinguish oil or gas-well fires although that work, which involves unusual conditions and methods, does not properly come within the classification of oil-well shooting. Some Factors to Be Considered in Shooting Wells Although nitroglycerin has been used extensively for more than half a century in shooting oil and gas wells, there is still a great deal of uncertainty as to the proper method of shooting or the amount of explosive required to produce best results in a particular formation. The possibility of shooting unproductive or cavey formations above or below the productive horizons, shooting into lower water, destroying casing seats, and the splitting or collapsing of casing strings, are factors that require consideration. The engineering departments of a number of the larger oil companies are making a study of methods of shooting, and the amounts of liquid nitroglycerin or other explosives required in shooting various productive

Jan 1, 1929

By R. Wachtell

IN order to study better the phenomena at work in various phases of diffusion of the Fe/Si system when compounded and alloyed by powder metallurgy methods, several attacks have been planned. Electrical, hardness and other measurements have been discussed e1sewhere.l,2 The metallographic phenomena will be considered here. Concerning the metallography of the ferrosilicon alloys, some initial discussion is in order. As this laboratory discovered to its chagrin, there are many traps that lie in wait for even the experienced metal-lographer when he deals with alloys of high silicon content. Chief of these is probably the anomalous behavior of these materials under conventional etching techniques. We have before us, for instance, Corson's paper" of 1928, wherein is mentioned and illustrated (probably for the first time) the peculiar "barley shell" structure sometimes found in these alloys. Again in 19412 he same author reports the structure in 5-14 pct silicon irons. Houghton and Becker mention its presence' but make only tentative effort to explain it. In 1943, Hurst and Riley6 discussed the "barley shell" and declared it to be a false structure, resulting from the peculiar and characteristic film-forming propensities of the alloy. At about the same time, Wrazej7 proved correct the contentions of Hurst and Riley, establishing pretty well the mechanisms of formation and identifying the constituents involved. Hurst and Riley6 a1so describe in their paper (1943) a "cracked film" structure, also a pseudo-morph, the precise nature of which they do not suggest. Careful examination of such a film reveals that it not only cracks but begins to curl away from the surface of the metal and peel, much in the manner of flaking paint. The careful microscopist will be able to focus on the topmost edge of the flake, and, by optical sectioning, follow it down to the metal surface. We have been able, by oblique illumination of such specimens, to observe the raised segment of the film, the shadow that it casts, and the mating segment on the metal into which it fits. As late as 1946, Hurst and Riley8 found occasion to correct misinterpretation of this "cracked film" structure in a work by others on a 12 pct Si/Fe alloy. The "barley shell" and "cracked film" pseudo-morphs are not the only ones encountered in studies of these materials. A third pseudomorph, which may, however, have some structural significance is a fine striation of the surface. Closely spaced and parallel striae extend entirely across single grains. Each grain shows a different direction for the striae, and different closeness of the spacing. The regularity of this structure, and the fact that the striae do not cross from one grain to another, suggest that the structure is a film cracking controlled in some way by the crystal plane orientation of the surface being etched. In general it is wise for the metallographer dealing with these alloys to cultivate a feeling of uncertainty not only of the more complex questions of interpretation, but also of the basic question of whether that which he sees is indeed a true representation of the structure. We have taken, as a first test of the validity of a structure, its reproducibility "in situ" after repolishing and re-etching of the samples. Thus we knew the "barley shell" to be false (fig. 1) even before encountering the definitive works on the subject. The Metallography of Silicon Diffusion in Laminate Bars: As a first step in the study of the metallography of the diffusion process, we have pressed a series of laminate bars. These bars, or "sandwiches" as we have termed them, were pressed with covering layers of iron powder, and a "filler" of the Fe/Si master alloy under study. Bar dimensions were approximately %, x 3 x 1/4 in. The total

Jan 1, 1951

By Edmund C. Pechin

I REGRET that I am unable to present this subject in definite form and detail. All I shall attempt at this meeting is to lay before you some curious facts, the bearings and explanations of which must be reserved for future consideration. I hope before the next meeting to have carried experiments far enough to furnish a more important contribution to the science of iron metallurgy. The Wickersham process consists in the introduction into the molten metal, as it runs from the furnace, of air from the hot blast. Mr. Samuel Wickersham is the originator of the plan, as applied in practice, although Mr. Martien had the idea a long time ago, and, I believe, .went to England about it. But at that time Mr. Bessemer was coming before the public with his invention, which engrossed the attention of iron-masters, and Mr. Martien accomplished nothing. The principal difficulty in our experiments at Dunbar was to get a practicable runner or trough, through which the molten metal should pass, and in which it should be exposed to the action of the blast. The runner we used was ten feet long, and perforated on the sides to permit the entrance of the air-currents. When we used a cast-iron and fire-clay runner, the heat was so great that before we were more than half done with a run, the lower part of the runner was melted, and we had a magnificent Fourth of July display of fireworks until the blast was shut off. We had to abandon fire clay. The runner with which we have had the best success ,is made of wrought-iron tubes, 2 1/2 inches in diameter, attached to a wrought-iron frame, and lined with a mixture of crushed conglomerate (quartz) and a little fire clay to give it cohesion. The wrought-iron shell curves inward over the upper edges, so as to catch and throw back into the current the flying sparks and particles of metal thrown out by ebullition. With this we have been able to run 12 to 14 tons at a heat with great ease. Mr. Wickersham has since prepared this material (pounded quartz) into a shaped brick or tile, with the necessary perforations for the passage of the air, which promises to answer every requirement for steady working. As regards the improvement in the quality of the iron, there seems to be no question. A large number of practical tests were made in

Jan 1, 1873

By Fred L. Morritz, Harold M. Manasevit, Richard Nolder, Arnold Miller

Experimental evidence is presented which confirnis the epitaxial relationship between the deposited silicon and the sapphire substrate. Four distinct modes of orientation relationships have been established. These have been shown to be Single-crystal gvowth retention as a function of surfaces oriented off ideal has been qualitatively indicated. Both full-circle goniometer X-ray techniques and replica electron microscopy have indicated varying amounts of microtwinning in the silicon. film, which may he caused by the mode of silicon formation. Parameters have been found where twin density is less than I pct. The early stages of' epitaxy of silicon m sapphire have been examined by electron-microscope techniques... and mechanisms have been proposed. THE first report of the deposition of single-crystal silicon on sapphire (single-crystal aluminum oxide) was made at the American Physical Society Meeting in Canada' by one of us and was subsequently published in the Journal of Applied physics.* This paper summarizes some of the work carried on in this area since that time, in addition to reviewing some of our earlier observations. The initial single-crystal deposits of silicon on sapphire reported were obtained on sapphire planes produced by cutting a sapphire rod perpendicular to its fastest growth direction, which is approximately 60 deg from the C axis. Direct correlations between the microstructure and X-ray data as to the single crystallinity as shown in Fig. 1 are evident. These deposits were identified as (111) silicon on the substrate oriented near the (1123) of sapphire. (Sapphire notations are designated according to the c over a ratio of 2.73.) It became evident that substrate quality and surface play an important part in successful epitaxy. For example, in Fig. 2 we observe an interesting

Jan 1, 1965

By C. S. Barrett

THE crystal imperfections known as faults in stacking (stacking disorder) are of importance to both fundamental and applied science and are receiving increasing attention. On the theoretical side there have been recent advances in the analysis of diffraction patterns in terms of stacking faults, and on the experimental side it has been found that certain metals develop a faulted structure on cooling through a phase transformation. Beyond this, little is known of what may be called the physical and mechanical metallurgy of faulting, although there has been no lack of discussion and conjecture as to the presence of faults in metals and the effect of faults on mechanical properties and microstructures. In the close-packed metals the nature of faults can be described very simply. Face-centered cubic (FCC) crystals consist of close-packed layers of atoms, (111) planes, stacked above each other in a definite manner. If one layer is designated as the A layer, the next must be a B or a C layer; that is, every atom of the second layer lies not above the atoms of the A layer, but nestles in the hollows between these, using the hollows designated as the B positions, or the equivalent hollows designated as C. If the sequence of layers is ABCABC...., so that layers three spacings apart are directly over each other, the crystal is FCC; if CBACBA ... it is an FCC crystal that is a twin of the former; if ABAB........or BCBC..it is hexagonal close-packed (HCP). A fault is a break in the sequence, such as ABCABABC .. . which has the effect of inserting an HCP lamella into an FCC crystal. Regularly spaced faults spaced two layers apart would convert an FCC crystal entirely to HCP, or an HCP to FCC. A fault in an FCC crystal is also equivalent to creating an FCC twin of minimum thickness; in fact, the entire crystal would be converted to its twin if faults were introduced regularly. (In HCP crystals, however, twinning does not occur on the basal plane and a fault on this plane is not identical with a thin twin). Faults are one of the possible causes for annealing twins,' for the strain markings that are brought out by etching deformed metal,'," for the altered X ray reflecting power of metal at slip bands that is revealed in X ray reflection micrographs,' for the extinction of Kikuchi lines in electron diffraction patterns, and for the hardening of latent slip planes.' Since other explanations of these effects are also available," there has been no direct proof of faults from deformation; yet it has appeared likely that they would occur. Faults resulting from phase transformations in metals, however, have been clearly revealed by diffraction in cobalt" and lithium. It is to be expected that the faulting tendency is greatest

Jan 1, 1951

By A. W. Ambrose

THE underground losses of oil exceed by hundreds of thousands of barrels all the oil that has been lost in storage, transportation, or refining. The quantity lost is, of course, indeterminate; but when it is considered that the contents of an entire oil field have been excluded from recovery by invading waters, some idea of the amount wasted may be gained. Similarly, enormous quantities of gas have been lost underground. Conservation of the oil, therefore, should start before it is brought to the surface rather than after it is placed in storage tanks. Water is one of the most important causes for underground losses and the operator should give as serious consideration to an underground flood of water as he would to a destructive surface flood. The best insurance, of course, is to have the wells drilled in such a manner that water has no access to the productive oil and gas horizons, and on abandonment the wells should be properly plugged. The encroachment of edge water and the occurrence of water in the base of an oil sand present a very serious problem to an oil company; sooner or later these waters are bound to cause considerable damage, if they do not entirely destroy the possibilities of further production. Too often, however, a field has been considered to be in a hopeless condition, whereas wells in as bad a condition in other areas have been repaired and the life of the field appreciably lengthened. The corrections are very often suggested by technical study. Very successful results have been accomplished by detailed underground work in the California oil fields, in Cushing, Oklahoma, and in other areas.

Jan 9, 1920

By Robert B. Kistler, Ward C. Smith

The borate industry is one of the few sectors of the mining and mineral-processing industry which the United States still dominates. Since about 1927, the United States has supplied over half of the world's total boron and borate raw materials, and many of the chemical derivatives as well. Chiefly responsible for this record are companies producing sodium borates from two large deposits in southern California, at Boron (Kramer) and Searles Lake. The sodium borates, or products derived from borax and borax-containing brines, are the preferred borates for industry because they are soluble in water and combine readily with most other chemicals. Calcium borates are required for certain end uses, and these are produced from smaller colemanite-ulexite-probertite bodies. Sodium-free borate compounds also are produced from boric acid, which can be manufactured from either sodium or nonsodium borate minerals. During the past hundred years, the use of boron compounds throughout the world has risen from a few tons per year to the equivalent of over a million tons of B2O3. Leadership in supplying borates shifted from country to country and from region to region during this period, generally as the result of the development of newly discovered deposits that were better in quality, more accessible, or more economically exploitable than previous sources (Table 1). Primary Products and End Uses The principal borate products offered by primary producers in the United States are listed in Table 2. In general, these products are utilized worldwide by almost all consumers, regardless of the original source of the primary borates, In the United States, the primary borates all originate in southern California. Colemanite is produced as crude or processed crude ore from the Death Valley area and is utilized by the fiber glass and ceramic industries without further treatment. Production from Searles Lake, CA is from brines that are processed in chemical plants where borax and other compounds are recovered and the principal borate products are produced. At Boron, CA, the world's leading producer is mining a deposit of mineral borax and operating a chemical refinery. The mineral borax is mined together with included clay, and refined borax or "10-mol" is one of the refinery products. The mineral and the chemical compound are identical, Na2B4O7 • 10H2O. In addition to ship¬ping all major refined borate products from [ ]

Jan 1, 1983

By AIME AIME

Award of a Gold Medal : to the Institute. The Jury of Awards of the Jamestown Ter-Centennial Exposition has conferred a gold medal, the highest distinction within its power,. on the American Institute of Mining Engineers for the excellence of its publications during the past decade. ; A half-tone photographic reproduction of both sides of the medal is given in the accompanying illustration.

Jan 7, 1908

By Carmine D. &apos, Lemuel Tarshis, Joel Hirschhorn, Antonio

Vapor-deposited nickel films in the thickness range 700 to 4360A were tested in uniaxial tension utilizing a microtester designed specifically for this study. Contrary to the findings of some investigators, a definite thickness-strength relationship was observed below 3000 A with a four-to sevenfold increase in strength over that of bulk nickel. The films were characterized by high elastic strains and little plasticity. On the basis of these and other reported data, it is suggested that the high strength level in metal films is related to the manner in which they are produced. Vapor deposition, owing to its severe quenching effect. is believed to promote the formation of point defects which inhibit dislocation movement. IN recent years it has been reported that metals, when in the form of thin films, exhibit extraordinarily high strengths. The data published to date have been primarily concerned with silver and gold because of the ease with which these metals can be vapor-deposited and their high resistance to surface oxidation. Previous investigations into the mechanical strength of thin films has uncovered an apparent dichotomy of view on film behavior. Beams and his co-workers have reported a definite dependence of strength on film thickness. Other workers,"-'6 however, in separate studies on the strength of poly crystalline and single-crystal films have found no such thickness-strength relationship. The study of thin-film strength is extremely difficult because of the many variables associated with film preparation, handling, and testing. Moreover, the manner of test employed by different investigators has varied quite radically, ranging from simple uniaxial-tension to biaxial-bulge testing. The work reported herein was conducted in order to determine the mechanical behavior of a structural metal when in the form of a vacuum-deposited thin film and to gain some insight into the reasons for the high strengths exhibited by metals having such a con- figuration. In this study a method of test was chosen which would yield results which are easily interpreted and lend themselves to comparison with properties of the same material in bulk form. Moreover, specimen-preparation parameters and film-handling techniques are set forth so that other investigators can properly compare their findings with ours. EXPERIMENTAL PROCEDURES A) Film Preparation. Vacuum deposition was performed in an 18 by 30 in. bell jar using a standard New York Air Brake Co. vacuum station with a 6-in. oil-diffusion pump. Before evaporation the system was pumped to a pressure of less than 2 x 10"5 torr. A shield was employed to protect the substrates from the emission of contaminants during the critical melting and outgassing of the evaporant. The source consisted of from one to six filaments (0.020 in. diam). The length of each filament was about 5 in. and was placed 6 to 8 1/2 in. from the substrate in such a manner that the substrate face was at 90 deg incidence with respect to the evaporant beam. The temperature of the source was 2000"~ during evaporation. The films were deposited onto a substrate arrangement which was composed of four basic components, that is: 1) a 3 by 1 in. glass slide; 2) a 22-mm sq micro cover glass on 1); 3) a 22 by 50 mm micro cover glass coated with collodion on 1); and 4) a stainless-steel sheet mask containing twelve rectangular openings of 1-mm and 2-mm widths and lengths of 5 mm laid over 3). Thus, test specimens of 1-mm and 2-mm widths are deposited onto a collodion substrate which precludes epitaxial effects in the specirnens. 17-le The rectangular cover glass and square cover glass were positioned in such a manner that a strip of film would be evaporated along the length and across the width of the large glass slide. This boundary of evaporated film was used to determine the film thickness by multiple-beam interferometry. The square cover glass was used for X-ray and chemical analyses. Thickness of the deposits was varied by changing the number of filaments used (one to six). The duration of evaporation was 30 sec for each filamgnt which resulted in a deposition rate of 8 to 20A per sec. Evaporations were all performed at room temperature; however, radiant heat from the source raised the substrate temperature to 40" to 60°C. All substrates were cleaned by ultrasonic agitation in a solution of spectranalyzed isopropyl alcohol. Collodion was deposited on the micro cover glass by immersion in solution of collodion in amyl acetate. B) Thickness Control and Measurement. Film

Jan 1, 1963

By Å. Sterten, R. Tunold, J. Brun, K. Dalatun

c axis compression behavior of beryllium single crystals at three purity levels under hydrostatic pressures up to 27 kbars was determined. Extensive non-basal slip, observed by two-surface trace analysis and transmission electron microscopy, occurred under a hydrostatic pressure of about 12 kbars (175 ksi) for the high-purity (twelve-zone pass) material and at about 19 kbar (275 ksi) for the lower-purity (zone-leveled) material. Prismatic loops with a (c + a) Burgers vector were observed in association with second-phase parti- A principal factor limiting the use of beryllium is its brittle behavior when tested at the usual strain rates (E = 10-4 sec- 1) at temperatures below about 200°C and under impact conditions at temperatures in excess of 200°C. It has been proposed' that the brittle-ness of beryllium is associated with the lack of a sufficient number of independent slip modes and the absence of a slip mode with a Burgers vector out of the basal plane [presumably (c + a) pyramidal slip mode] and to the ease with which beryllium cleaves on the basal and second-order prism planes. The absence of pyramidal slip has been attributed to a high Peierls-Nabarro stress associated with the motion of dislocations with a (c + a) vector and the ease with which cleavage occurs on the basal and second-order prism planes. The experimental evidence in support of the proposed explanation for the brittleness of beryllium is far from complete; for example, that the ductile-to-brittle transition in polycrystalline beryllium is associated with the operation of profuse (C + a) slip has not been unequivocally established. The occurrence of (c + a) slip ({1122}(1123)) has been experimentally established2-5 under conditions where basal and prism cleavage are restricted in a c axis compression test. In these investigations (C +a) slip was found in high-purity beryllium single crystals tested in c axis compression* at 200°C and in Be-4.4 pct Cu and Be-5.2 pct cles in the lower-purity materials tested. The loops were related to surface "extrusions" observed on many of these same specimens. Nonbasal dislocations operating on (1122) planes with a (c + a) Burgers vector were observed. The presence of c and a dislocations together with (c + a) dislocations suggests that the (c + a) dislocations dissociate presumably on unloading or after failure of the test crystals to c and a dislocations. terial, (c + a) slip has only been observed near the the fracture4 surface in room-temperature c axis compression tests. Fracture in these tests occurs without measurable plastic flow, as determined with a strain sensitivity of 10"6. Since it has been shown for many metals that the application of hydrostatic pressure suppresses fracture,?-' it was felt that studying the behavior of unalloyed beryllium single crystals stressed in c axis compression under a hydrostatic pressure would reveal whether (c + a) can occur if fracture was prevented, and that it might elucidate the role of (c + a) slip in the ductile to brittle transition. Evidence that (C + a) slip is associated with increased ductility in a high-pressure environment has been found in stress-strain tests on poly crystalline beryllium.10 The present paper describes a study on the influence of a hydrostatic pressure environment on the occurrence of (c + a) slip in beryllium single crystals. Material of two purity levels was tested in c axis compression over the pressure range ambient to about 27.5 kbars.* 1) MATERIAL PREPARATION AND CHARACTERIZATION Two lots of low-purity single-crystal beryllium were used. The first lot was "ingot secondary refined grade" and designated lot A. The second lot (lot B) was produced by a two floating zone pass zone-leveling operation in an argon-filled sealed quartz apparatus on a 1-in.-diam by 12-in.-long bar of Pechiney secondary refined-grade vacuum-cast and hot-extruded material. The high-purity material (lot C) was made by traversing twelve floating zone passes through a similar bar of Pechiney secondary refined-grade vacuum-cast and hot-extruded material. In a series of spark cutting and lapping procedures,11 single-. crystal specimens some 0.12 in. sq by 0.30 in. high were made with the sides Parallel to the first- and second-order prism planes and the basal plane within 3' of arc of the top and bottom surfaces of the specimen. Such an accurate orientation is necessary because of the large difference in resolved shear stress

Jan 1, 1970

By C. H. Herty

The reactions that occur in the basic open-hearth process are complicated and are subject to many different factors such as temperature, slag composition and rate of boiling of the bath. It is difficult, therefore, to present an extended theoretical discussion of open-hearth operations without confusing the theory of the process with the application of the theory. This paper attempts to present some of the theory of the open-hearth process without mentioning theory at any point, simply giving some of the practical applications of results founded both on theory and practice and on experimental work both in small and large furnaces. It is hoped that an answer to a number of questions commonly asked by the open-hearth operator may be found in this paper. Discussion of the subject matter is taken up more or less in the order in which a heat ie worked, beginning with the oxidation of the scrap charged, sulfur absorption by the scrap, calcination of the limestone, and extending into the pig iron for the charge, the slags formed during the process, and some of the phenomena occurring in deoxidation of the steel and in its action in the molds. Oxidation of Scbap When scrap is charged into a furnace it immediately begins to oxidize, Oxidation is carried out by.three reactions: Fe + H20 + FeO + Hz (absorbs heat) (1) Fe + C02 + FeO + CO (absorbs heat) (2: Fe+ ½O2 + FeO (gives off heat) (3: The product of oxidation contains some Fe3O4, but FeO usually predominates on account of the iron present in close contact with the scale formed For a given type of scrap the amount of oxidation is controlled by thc fuel and by the excess air being carried in the furnace, the temperature 01 the furnace, and the length of time that the scrap is in contact with the furnace gases. In general, less oxidation occurs when the furnace is rur hot so that the scrap melts rapidly. More important in operation thar the two variables atmosphere and temperature, is the type of scrap being

Jan 1, 1929

THE discussion of this topic at the Open-hearth Conference at Detroit on Nov. 3, 1927, was opened by statements of the general principles involved, made by manufacturers of molds. Because of their general interest they are printed below. WILLIAM HAIL RAMAGE,* Hubbard, Ohio.-I did not come prepared to read a paper, thinking. the most I would be called upon to do would be to make a few, remarks by way of discussion. A number of our friends have pre-viously asked questions. similar to this which really does not permit a direct "yes" or "no" answer. If I may he pardoned for so doing, I believe it advisable to discuss rather what we consider the principal factors which in-fluence mold life. I think possibly a little undue weight has been given to the subject of the analysis of the metal. For the last eight years we have spent a lot of time, effort, and money investigating this very problem from a chemical, physical and microscopic standpoint. We have had the benefit of complete records and history of over 100,000 molds in service at a variety of plants and over long periods of time. Obviously, I cannot be so specific that I should divulge information that is really a trade secret. In our opinion the principal factors influencing mold life are: (1) design of the mold; (2) process of manu-facture, including workmanship; (3) care in the steel plant or what might be termed "the use or abuse" in the steel plant; (4) the analysis of the iron and the physical con-dition of it. Under normal conditions these factors are of importance in the order named, although in specific cases they might be rearranged in any order you choose. For instance, the best mold made can be destroyed in one or two pours by subjecting it to certain conditions which are occasion-ally met in steel plant practice. Obviously, in that case, nothing else matters but that one item. On the other hand, I have seen molds made of such a terrible design that it was a foregone conclusion it would have to be broken after the second pour of the ingot to get it out. In that case, nothing but design mattered. As to the effect of process of manufacture, let me cite a case. Some years ago there were two batches of molds sent to a certain company. They were the same sized molds, used under the same conditions and in the same kind of service. There were, 20 molds in each batch. The second batch sent gave ten times the life of the first batch. It is true that the design was changed a little, but not very much, and it was not. a bad mold to begin with. It is possible that the iron may have been better in the second consignment but not very much. In my opinion, it is con-servative to say that of the 900 per cent improvement in life, 5 per cent was probably due to better iron, 25 per cent to better design and the remaining 870 per cent to process of manufacture and workmanship.

Jan 2, 1928

By H. H. Hausner, H. S. Kalish

IN recent years zirconium and beryllium have become of great interest because of their special properties. Zirconium is known for its remarkable ability to absorb the gases oxygen, nitrogen and hydrogen, has extensive use as a getter in electron tubes and has indeed become the primary metal in the manufacture of photoflash bulbs. Beryllium is of interest because it is light metal and as such could supplement aluminum and magnesium in light metal applications. The late development of zirconium ductile at room temperature produced by both the iodide and calcium reduction methods has stimulated frequent articles on this metal in the recent literature. Beryllium is so closely akin to zirconium crystall-ographically that some investigators are of the opinion that beryllium should be ductile at room temperature if it were pure enough. The crystallographic relationship of beryllium and zirconium, the interest created in Be-Zr alloys where the zirconium is believed to function as a remover of solid solution gas in beryllium and thus increase the ductility of the beryllium rich alloy, and the amenability of these metals to powder metallurgy methods stimulated this approach to an investigation of the system Be-Zr. Preliminary work showed that a zirconium compact melted when pressed in contact with a beryllium compact and sintered at 1250°C, without any apparent final bond between the two. A search of the literature revealed nothing pertinent about the Zr-Be system or about any zirconium - beryllium alloys. In 1936 Misch³ vaguely identified the compound ZrBe2 and reported that it has a deformed cubic structure. Two patents," , were issued to Mach-lett Laboratories in 1943 and in 1946 regarding the addition of small amounts of zirconium to beryllium in order to improve the ductility of beryllium so that it may better be used for X ray windows. In considering the alloy formation of beryllium with other metals Raynor thought it unlikely that zirconium would have any solid solubility in beryllium. From this indefinite information nothing could be ascertained about the possible use of Zr-Be alloys or the use of these metals intimately. A brief preliminary study of the system Zr-Be by powder metallurgy methods was undertaken to provide regions for more intense studies of Zr-Be alloys and as a guide to a formal phase diagram determination. The investigation described in the following pages was completed in less than three weeks. The usefulness of this rapid method to facilitate phase diagram studies and new alloy investigations will be shown. Materials and Procedure Zirconium powder was produced from crystal bar stock of high purity supplied by Foote Mineral Co. The crystal bar was converted to hydride at 730°C, crushed, and the hydride decomposed in purified argon at 850°C. 60 pct of the powder passed through a 325 mesh screen, 40 pct of the powder was —140 mesh, +325 mesh and the average particle size of the total was 8 to 12 microns. The beryllium powder was used as re-

Jan 1, 1951

By Henry Lloyd Smyth, J. Ralph Finlay

The most important area of the so-called Keewatin rocks of northern Minnesota is that which runs westerly from Lake Saganaga, near the national boundary, and finally disappears beneath the drift (or has not been farther traced), in the neighborhood of Vermilion Lake. With this belt we have a general acquaintance, extending back some four years. During the past year we have had the opportunity of studying in considerable detail a small part of it, embracing an area of about 12 square miles on the south and east shores of Vermilion Lake. In this paper we desire to record our observations and conclusions, which seem to us important. II.—Literature. Outside the Minnesota Geological Survey, the list of the investigators who have studied the geology of the Vermilion Lake area is not long. Whittlesey, in 1876,* mentioned the occurrence, in the area about Vermilion Lake, of rocks resembling the Canadian Laurentian. Chester,? in 1884, described the iron-ore at Vermilion Lake as occurring in connection with jasper and quartzite, intimately bedded with the country-rock, chiefly sericite schist, and standing in a nearly vertical attitude. The Vermilion iron-bearing rocks, and those of the Mesabi range, he says, are of the same age.

Jan 1, 1896

By J. B. Austin

IN considering so complex a process as the smelting of iron in the blast furnace, there is obviously no single method of calculating efficiency that gives a complete appraisal of the performance of the furnace in all its several functions; such a comprehensive view as is required to evaluate producing ability and manufacturing costs for a given furnace is obtained only by considering a group of efficiencies, each of which measures the performance of the furnace from a specific point of view. For instance, there is the rate of consumption of coke per ton of iron produced, which is probably the most frequently considered, and is certainly one of the most important of the group; there is the efficiency of recovery of iron charged; and there is the efficiency of utilization of energy, both chemical and thermal, in some respects related to the former two yet in other ways independent of either. In each of these cases, the calculation can be made on the basis of the actual input of material or energy, or it may be based . upon a comparison with the minimum amount of material or energy that would be required by a "perfect" furnace; that is, an imaginary ideal furnace analogous to the perfect steam engine used in thermodynamic calculations, when this furnace is operating under optimum conditions. Moreover, the furnace itself can be considered either as an apparatus for smelting iron or, taking a somewhat less common point of view, as a gas producer yielding iron and slag as by-products. Some of these effi-ciencies are more useful than others, yet all are instructive; for a knowl-edge of them not only leads to good engineering practice from the standpoint of control but also discloses limits to possible improvement in performance and indicates the lines along which improvement is most likely to be profitable. Estimates of some of these efficiencies have appeared from time to time in the literature, but many of them are open to objection because they are based on data of uncertain accuracy or because they have been calculated without due regard to the thermo-dynamic principles involved. Moreover, so far as the author is aware, no general survey of the blast furnace comparing its performance in all the aspects mentioned has been made.

Jan 1, 1938

By Charles S. Barrett

The experiments reported in this paper have been fruitful in disclosing the mechanism of the deformation of iron in compression. They have established the nature of "deformation bands," "etch bands," or "X-bands," that have been a recognized but little understood feature in the structure of cold-worked metals since the early days of metallography, and have shown the role of the bands in the development of preferred orientations by cold-working. The work has also shown the relation of the orientation of individual grains to the preferred orientation of the aggregate. Some of the methods previously used in the determination of the indices of slip planes and slip directions are shown to be untrustworthy in the presence of deformation bands. The conclusion is reached that many slip planes and slip directions must operate during each stage in the compression of a single crystal, and that theories failing to take account of this require revision. In conducting the experiments a method of compression has been used by which extreme reductions can easily be reached, even to the limit set by the metal's capacity to deform without fracture. The work is a portion of a research program on the plastic properties of iron and steel. It is being used as a foundation for studies of orientntions resulting from recrystallization and is being extended to other metals and other types of deformation. Previous Work The previous experiments are few and have given confusing results Onol compressed a polycrystalline alpha-iron specimen between two flan plates of a testing machine and found that severe deformation oriented the crystals into a duplex preferred orientation, one set of crystallites having a cube diagonal of the body-centered cubic lattice parallel to the compression axis, and another set having a cube axis parallel to the compression axis. We shall speak of this structure as a double fiber texture of the type [111] + [100]. Wever2 also made an X-ray determination of the texture

Jan 1, 1939

By Charles S. Barrett

The experiments reported in this paper have been fruitful in disclosing the mechanism of the deformation of iron in compression. They have established the nature of "deformation bands," "etch bands," or "X-bands," that have been a recognized but little understood feature in the structure of cold-worked metals since the early days of metallography, and have shown the role of the bands in the development of preferred orientations by cold-working. The work has also shown the relation of the orientation of individual grains to the preferred orientation of the aggregate. Some of the methods previously used in the determination of the indices of slip planes and slip directions are shown to be untrustworthy in the presence of deformation bands. The conclusion is reached that many slip planes and slip directions must operate during each stage in the compression of a single crystal, and that theories failing to take account of this require revision. In conducting the experiments a method of compression has been used by which extreme reductions can easily be reached, even to the limit set by the metal's capacity to deform without fracture. The work is a portion of a research program on the plastic properties of iron and steel. It is being used as a foundation for studies of orientntions resulting from recrystallization and is being extended to other metals and other types of deformation. Previous Work The previous experiments are few and have given confusing results Onol compressed a polycrystalline alpha-iron specimen between two flan plates of a testing machine and found that severe deformation oriented the crystals into a duplex preferred orientation, one set of crystallites having a cube diagonal of the body-centered cubic lattice parallel to the compression axis, and another set having a cube axis parallel to the compression axis. We shall speak of this structure as a double fiber texture of the type [111] + [100]. Wever2 also made an X-ray determination of the texture

Jan 1, 1939

By Gerhard Derge, J. Warren Stewart

Extrusion processes are used in the commercial production of a wide variety of products, as indicated by the review presented a few years ago by D. K. Crampton.' Most writers have confined themselves to a general description of the equipment and products and the engineering aspects of the process. The few studies that have dealt with the metallurgical side of extrusion have been concerned primarily with an examination of the mode of flow of the metal during extrusion. This has been accomplished by the use of composite billets, by scribing grids on symmetrical sections of billets and observing the change of dimensions in the gridwork, or by examining microstructures in extruded sections.2"8 Ariotlier limitation of these original studies is that they were confined to the extrusion of very simple shapes, usually rods having a diameter of about one-fourth that of the billet. Tin is particularly well suited to the extrusion of collapsible tubes and similar shapes in which the extruded section is very small in comparison to the diameter of the billet or slug. In modern production, impact extrusion methods are generally employed, therefore the thickness of the slug is small compared to its diameter. Under these conditions the process differs considerably from the processes that have been most fully described in the literature, and it is known that the quality of the product is very sensitive to slight variations in any one of the many variable factors involved, such as coinposition and structure of the alloy, rate of extrusion, temperature, shape of punch and die. An exhaustive examination of all of the above-mentioned problems promises to produce so many data that it seems advisable to initiate the reports at this time, even though all of the factors outlined have not been examined fully, and to confine this paper to a description of the apparatus and method. Only tin and its alloys with small amounts of copper have been considered. These are the alloys most commonly used in this country for the production of the type of articles already described.

Jan 1, 1940

By Gerhard Derge, J. Warren Stewart

Extrusion processes are used in the commercial production of a wide variety of products, as indicated by the review presented a few years ago by D. K. Crampton.' Most writers have confined themselves to a general description of the equipment and products and the engineering aspects of the process. The few studies that have dealt with the metallurgical side of extrusion have been concerned primarily with an examination of the mode of flow of the metal during extrusion. This has been accomplished by the use of composite billets, by scribing grids on symmetrical sections of billets and observing the change of dimensions in the gridwork, or by examining microstructures in extruded sections.2"8 Ariotlier limitation of these original studies is that they were confined to the extrusion of very simple shapes, usually rods having a diameter of about one-fourth that of the billet. Tin is particularly well suited to the extrusion of collapsible tubes and similar shapes in which the extruded section is very small in comparison to the diameter of the billet or slug. In modern production, impact extrusion methods are generally employed, therefore the thickness of the slug is small compared to its diameter. Under these conditions the process differs considerably from the processes that have been most fully described in the literature, and it is known that the quality of the product is very sensitive to slight variations in any one of the many variable factors involved, such as coinposition and structure of the alloy, rate of extrusion, temperature, shape of punch and die. An exhaustive examination of all of the above-mentioned problems promises to produce so many data that it seems advisable to initiate the reports at this time, even though all of the factors outlined have not been examined fully, and to confine this paper to a description of the apparatus and method. Only tin and its alloys with small amounts of copper have been considered. These are the alloys most commonly used in this country for the production of the type of articles already described.

Jan 1, 1940

By B. L. Averbach, M. F. Comerford, M. B. Rough

The volume fraction of ß phase was determined in a Ti-6Al-4V alloy by measurements of integrated diffraction intensities. The (0002), and (100)ß diffraction lines were chosen because this combination minimizes the errors resulting from preferred orientation. The difficulties arising from fluorescence radiation were eliminated by use of a diffracted beam monochromator. A specimen quenched from 1475OF (800°C) contained approximately 5 pct ß, but in specimens quenched from higher temperatures no ß was found. The ß phase formed during aging, and in specimens solution treated at 1570oF (855oC) approximately 10 pct ß was present after aging at 1000°F (540°C) for 24 hr. This ß appears to form by decomposition of martensitic a'. ThE kinetics of the reactions which occur during the heat treatment of titanium alloys are complex ' and not completely understood. It has been proposed that hardening occurs in some alloys' on aging by the precipitation of a transition phase w followed by the formation of the stable a and ß phases. It has been proposed for other alloys2 that the a' marten-site decomposes by precipitating finely dispersed a particles. Most investigations have been hampered by the difficulties of determining quantitatively the amounts of the various phases present. This paper is concerned with the measurement of the amount of ß phase by an X-ray method, similar to one developed for the determination of retained austenite. The principal new feature was the use of a mono-chromator in the diffracted beam in order to reduce the fluorescence arising from the sample. EXPERIMENTAL PROCEDURE The experiments were carried out on an alloy of nominal composition Ti-6Al-4V (actual weight percentages: 6.2 Al, 4.1 V, 0.02 Mn, 0.17 Fe, 0.005 H, 0.03 C, and 0.02 N). The material was received as 5/8-in.-diam centerless ground rods in the annealed condition. The heat treatments were carried out in a vacuum of approximately 0.03µHg. The X-ray intensity measurements were made on 3/8-in. thick discs. The surface was prepared by grinding off about 0.060 in. and electropolishing in a solution af 60 ml (70 to 72 pct) perchloric acid in 1000 ml glacial acetic acid with a current density of 0.5 amp per sq cm.q The X-ray determination is based on the proportionality of the diffracted intensity of each line to the volume fraction of the corresponding phase. In calculating the intensities for a powder sample it is assumed that a large number of grains con- tributes to the diffracted intensity and that the grains are oriented at random. The presence of preferred orientation introduces serious errors in the relative intensities. The material used in this investigation exhibited a strong preferred orientation, which could not be removed by heat treatment. Other investigators have also found that preferred orientation may be retained after phase transformations. Glen and pugh5 performed a detailed analysis of the randomness expected after several allotropic transformations, but stated that this is not observed. Burgers,6 and Burgers and Ploos van Amstel,7 found that, in zirconium, the original orientation is retained after two phase transformations. Newkirk and Geisler8 observed similar behavior in titanium. On the basis of this evidence, it appears that, in the absence of plastic deformation, textures present in annealed titanium alloys are retained. Heating an a-ß alloy to the all-ß region and subsequent cooling to room temperature do not make the orientation of the mar-tensite different from that of the original a phase. In the present investigation it was possible to take advantage of the crystallographic relationships involved in the martensitic transformation to minimize the errors associated with preferred orientation. The relative orientation for titaniu-m marten-site9 takes the form (0001), 11 (110)ß; [1120], 11 [lll]ß. The same relationship has been proposed for zirconium' and certain titanium-base alloys.10-12 Additional sets of approximately parallel planes have been determined for titanium-nickel alloys." The influence of preferred orientation can be minimized by comparing intensities from parallel planes in the two related phases. If it is assumed that each family of planes in a given phase is equally well populated, the effect of preferred orientation can be eliminated by using the normal multiplicity for the family of planes since each set of parallel planes is equally preferred for any orientation of the sample relative to the X-ray beam. The most suitable combination of reflections in the Ti-6A1-4V alloy appeared to be (0002), and (110)ß It must be recognized that the ß formed during aging of the Ti-6A1-4V alloy is a precipitate rather

Jan 1, 1960