Search Documents

By R. W. Hertzberg, R. W. Kraft

A study of the fracture behavior of unidirectwn-ally solidified Cu-Cr eutectic alloy was performed. Fractured whiskers, grain boundaries, and the interface between proeutectic Cr dendrites and the Cu matrix were the predominant failure initiation sites where grain size was larger. Strain induced void formation was restricted at lower solidification rates. This was attributed to a lack of adequate plastic constraint and a probable preferred orientation. A modification of the Crussard et al. model is presented to explain the appearance of "elongated dimples" on the shear fracture surface. A Cu-Cr alloy containing about 1.8 at. pct Cr solidifies by a eutectic reaction forming filamentary crystals of chromium within a continuous copper solid solution matrix.' Webb and Forgeng2 have shown by bend tests that the extracted chromium filaments, which are ordinarily curved and branched (due to random solidification), have the high strengths associated with whiskers. If an ingot of the eutectic alloy is unidirectionally solidified and appropriate control exercised over the thermal gradient, growth rate, and impurity level, the chromium fibers can be forced to solidify as fibers which are substantially parallel to the growth direction, Fig. 1. Uniaxial tensile tests on these straight chromium fibers extracted from controlled ingots3 have confirmed the earlier bend test results on curved fibers. Combining the facts that the strength and modulus of the chromium filaments are higher than the more ductile copper matrix and assuming that a "good bond" exists between the two phases, the Cu-Cr controlled eutectic system fulfills the requirements for effective fiber reinforcement of ductile matrices as established by studies on fiber glass reinforced plastics and other two-phase systems.4 Therefore, it was decided to study the fracture characteristics of morphologically simple specimens of chromium fiber reinforced copper (i.e., specimens of the controlled eutectic with substantially parallel reinforcing fibers) with the objective of establishing the dominant aspects of fracture. PREVIOUS WORK Comparatively little work has been done to understand the manner in which ductile alloys fail be- cause of the limited demand for this kind of information. Ordinarily ductility is specified for safety or similar reasons and when a part deforms plastically its useful life is terminated. In recent years, however, a number of investigators have begun to

Jan 1, 1963

By R. A. Deju, R. B. Bhappu

Further information on the surface characteristics of the silicate minerals was obtained by experimentally correlating the oxygen-silicon ratio of the silicates with their electrokinetic properties. Specifically, the behavior of the minerals in an electric field was investigated using zero point of charge as a parameter. A modified electrophoresis cell was used for the determination of electrophoretic mobilities. It was shown that there is an increase in the zero point of charge with increasing oxygen-silicon ratio in the silicates. Finally, a chemical interpretation was presented to describe the surface phenomena observed in the experiments. In recent years great interest in surface chemistry has produced a number of methods to study the surfaces of minerals and to observe the phenomena occurring at their interfaces. One such method is discussed in this paper. A rather complete review of the surface characteristics of the oxide minerals has been undertaken by parks,' but, a similar study has not been made for the silicate minerals. Two previous papers by the authors2'3 attempted to remedy this situation. In these papers it was demonstrated that the reaction between the silicate mineral particles and acidic water involves mainly an exchange of metal ions for hydrogen ions on the surface of the solid, leading to an increase in pH of the aqueous phase. Also, the degree of reaction was found to depend on the oxygen-silicon ratio of the silicate structure, being least for the quartz and greatest for the olivines. A hypothesis was then set forth explaining that upon the fracturing of a silicate mineral, the oxygen-metal bond (which is almost entirely ionic in character) will break more easily than the stronger oxygen-silicon bond. This results in the exposure of unsatisfied oxygen sites on one hand and active, exchangeable cations on the other. These active sites on the fractured surfaces are then available for reaction with the hydrogen ions in acidified aqueous solution. Thus, an increase in degree of adsorption of hydrogen ions occurs as the oxygen-silicon ratio increases due to the presence of a larger number of active sites on such minerals. A correlation between oxygen-silicon ratio and electrokinetic properties will be further pursued in this paper from both the theoretical and experimental points of view. Efforts will then be made to present a chemical interpretation of surface phenomena observed in the experiments. It is believed that this study may supply pertinent information on the behavior of silicate minerals in froth flotation systems. ELECTROKINETIC STUDIES Equipment: In a previous paper,2 Deju and Bhappu described a simple method for determing the zero point of charge using a potential across a cata-phoresis cell and observing particle movement by means of a Rayoscope* optical system. This setup is simple in design and operation and extremely reliable. With care, reproducible results within 1.5% accuracy may be obtained. A new setup has been developed, based partly on the design by Zeta-Meter Corp.4 and partly on previous cells used at the New Mexico Bureau of Mines. This new, modified cell is shown in Fig. 1. Although

Jan 1, 1967

By Leonard B. Gulbransen, John R. Lewis, W. Martin Fassell, J. Hugh Hamilton

T. E. Leontis (The Dow Chemical Co., Midland, Mich.)—This paper is of particular interest to me because of my own work with F. N. Rhines on the oxidation of magnesium and magnesium alloys a few years ago. The authors are to be complimented on their development of an accurate and reproducible technique for measuring ignition temperatures and on their comprehensive study of the many variables that affect the ignition temperature of magnesium. It is indeed gratifying to see that they have obtained a good correlation between ignition temperatures and the oxidation rates reported by us. The correlation is valid not only with composition within one alloy system but also between alloy systems; that is, alloying elements which effect the greatest increase in oxidation rate also produce the greatest decrease in ignition temperature. There are a few points upon which I would like to comment. In attempting to correlate ignition-temperature data, one must be sure that the same definition of this quantity is used by all investigators. It does not appear to me that such is the case in the authors' comparison of their data with the theoretically calculated values of Eyring and Zwolinski. The equation derived by these investigators defines the ignition temperature, To, as the temperature at the gadoxide interface, whereas the present authors use the metal temperature as the criterion for ignition. The contradiction in the effect of oxide-scale thickness on ignition temperature between the predictions of the Eyring-Zwolinski equation and the observations reported in this paper indicate that some variable has not been taken into consideration. Could that be the geometry and size of the specimen? There is a marked difference in the type of specimen used in this investigation and that used in our work which formed the basis of Eyring and Zwol-inski's theoretical treatment. Another factor which plays an important role in ignition is the vapor pressure or the rate of vaporization. Combustion can safely be assumed to take place in the vapor phase by the reaction between vaporized magnesium and oxygen. Thus, a more accurate theoretical analysis may be made on the basis of the rate of vaporization which may be the controlling rate of the process. The effect of a large number of alloying elements on the ignition temperature has been reported in this paper, but beryllium was not included. Practical experience dictates that beryllium markedly decreases the burning tendency of magnesium. I was wondering if the authors plan to study the effect of beryllium in their future work. The authors predict that concentrations of sulphur dioxide in the furnace atmosphere greater than 5.8 pct would be expected to increase the ignition temperature to values still higher than those they measured. I would like to mention that large concentrations of sulphur dioxide markedly increase the rate of combustion of magnesium once ignition has started. Although it has been shown in the paper that the ignition temperature of magnesium in oxygen increases with increasing sulphur dioxide content up to about 1 to 2 pct, in practice relatively low-melting commercial cast alloys (AZ63A and AZ92A) are being continuously heat treated at temperatures just below the melting point in air containing 0.5 to 0.75 pct SO*. In regard to the change in color of the oxide scale observed on magnesium and magnesium alloys just prior to ignition, I would like to mention that in our work alloying elements were found to color the usually white magnesium oxide even though ignition did not occur. For example, the oxide formed on Mg-A1 alloys was gray, increasing in intensity with aluminum content in the alloy. Finally, I might suggest that the authors indicate their source of the value of 0.8 g per cc for the density of MgO as it is formed on magnesium upon oxidation at elevated temperatures. W. M. Fassell, Jr. (authors' reply)—The comments by Dr. Leontis are very excellent ones and I will attempt to answer them in order. First, the problem of ignition of magnesium is a rather difficult one since many factors are involved. Concerning the comparison of the To in the Eyring-Zwolinski equation, eq 4, with the experimentally determined values, it will be noted that the calculated and experimental values of the ignition temperature in Table I are not self-consistent. In the case of the 1.78 pct A1-Mg alloy the calculated value is 49°C below the experimental value; for the 3.81 pct A1-Mg alloy, 122°C below the experimental value; for Mg with 5x10-' cm film, 19°C above the experimental value; for Mg with 2x10-I cm film, 28 °C below the experimental value. Thus, if it were merely a matter of difference of location of temperature measurement the calculated ignition temperature would always be below the experimental value, the difference being due to the thermal gradient through the oxide film. The possibility of a thermal gradient in the magnesium metal must be considered. From Carslaw and Jaeger,'Y t can be shown that the maximum temperature gradient that could exist between the oxide-metal interface and the center of the sample is of the order of O.Ol°C. The geometry and size of the specimen could certainly have some effect on the ignition temperature. The equation for ignition that has been proposed in reference 14 is of the following type containing terms to account for this and other factors: M dT AHv(T) =Cp--------------\-J(.T—TB) + ZAHl-M A dx where AH is the heat of reaction, v(T) is the velocity of the reaction at temperature, Cp is the heat capacity of sample, M is the mass of sample, A is the area of sample, t is time, J is the total coefficient of heat transfer outward from the reaction zone, TR is the temperature of the bath or furnace, and AH,, is the heat associated with any phase change involved. Prior to the instant of ignition, the vapor pressure of magnesium is of no special significance. After ignition, neither eq 4 nor the above equation is applicable. The actual combination of magnesium cannot safely be assumed to take place in the vapor phase. While experimental data is lacking to support a hypothesis that ignition does or does not occur in the vapor phase, some observation on the pressure ignition experiments may be of interest. At high oxygen pressures, once ignition has occurred, the reaction of magnesium with oxygen approaches near explosive violence, the entire sample being consumed in probably less than 1 sec. At atmospheric pressure it usually requires 15 to 20 sec. Thus it appears that the oxygen concentration becomes the rate determining factor. Further, if burning magnesium is observed through darkened glass (Lincoln Super-visibility Shade No. 12) the magnesium sample is very much hotter than the "smoke" and the outline of the sample is retained perfectly. No "flame" is visible above the metal. No work was done on Mg-Be alloys. We do, however, intend to study this problem in the near future.

Jan 1, 1952

By Dr. Egleston

While I thoroughly appreciate the United States testing-machine at the Watertown Arsenal, and regard it as the most accurate testing-machine that has yet been built, I wish that I could say that it is complete in all respects. I not only fully appreciate it, but I have given up advising thesending of material to be tested anywhere else. It is five or six times more expensive to use this machine than any of the others, but the results which are obtained from it are, I think, perfectly reliable, and of such a character that the tests are all comparable with each other. It has proved, beyond a doubt, that the system of testing specimens of' diminished area, and then calculating that the metal examined will be as many times stronger as its area is greater, is an absolutely vicious one. I am quite prepared to say, that, either from their limited size or faulty construction, most of

Jan 1, 1882

By Fred T. Greene

(San Francisco Meeting, September, 1915) MOST of. the recent discussion of the mineral land law published in the Transactions is in the abstract-an exception being Mr. Goodale's paper, The Apex Law in the Drumlummon Controversy,1 which illustrates in concrete instances many of the practical disadvantages of what Dr. Raymond has. called "The Law of the Apex." The present paper, it is hoped, may serve a similar purpose, emphasizing the necessity for a change in our mining laws, and bringing home to mining engineers some of the defects and dangers of our present code. There are many storm centers of "apex litigation" in the Rocky Mountains; and not the least of them is the Wardner camp, where such litigation has been almost continuous since 1892, and the end is not yet. In their decisions, the courts have accepted the claims of the litigants that the " Wardner vein" is a broad zone varying from 250 to 500 ft. in width at the surface. This is the simplest theory which could have been advanced, and probably decreased, rather than augmented, the number of contests; in fact, every one of the claim owners seemed to feel that the greatest advantage would accrue to him if this theory were adhered to. The dominant structural feature of the Wardner vein is a persistent fault, striking N. 40° W., clipping about 40° to the southwest and called the "Wardner foot wall." Fig. 1 is a composite of two adjacent cross-sections of the vein and is a fair representation of the relative size and shape of the orebodies and their relation to the "Wardner foot wall." The country rock is a comparatively thin-bedded sericitic quartzite which has an average strike of N. 80° W. and clips at high angles to the north and south.

Jan 5, 1915

By A. L. Baxley

An Untapped Energy Resource As much as 20 billion cubic feet of natural gas per day are flared from remote oil fields for lack of a commercially viable means of capturing, transporting, and marketing such gas. The magnitude of these gas flares can be put into perspective from an early satellite photograph (Fig. 1) which shows lights from the major cities of Russia and Eastern Europe dwarfed by the natural gas being flared in the Persian Gulf. Together, these wasted resources contain the energy equivalent of about one-half of the gasoline consumption in the United States today (Fig. 2). Additional trillions of cubic feet of natural gas are "shut-in" because of no economically viable means of commercial recovery. Methanol and liquified natural gas (LNG) are the only two practical fuel products which can be produced economically from these gas supplies. Many of these gas supplies are less than 500 million cubic feet of gas per day, making an LNG facility uneconomic. In contrast, barge-mounted methanol plants can economically convert billions of cubic feet of gas per day into safe, clean-burning methanol. The methanol approach offers the only economical route to transform vast, known reserves of natural gas into a highly versatile primary liquid fuel. Methanol Barges: An Innovative Solution The barges will be towed to suitable offshore and upriver locations such as Alaska, South America, Africa, Southeast Asia, Australia, New Zealand, and the South Pacific Islands, as well as fields in the Persian Gulf and Mediterranean Sea. At the offshore production site, a barge will be anchored by a single point mooring buoy that will also serve as an entry point for natural gas feedstock and an offloading point for methanol (Fig. 3). At some sites the barge would be beached. Each barge will produce methanol and store it in internal tanks with a capacity of 18 million gallons. The methanol will be offloaded into conventional tankers and safely transported directly to market. Unlike LNG, methanol requires neither specially built carriers nor specially built receiving terminals. Once a particular gas field has been exhausted, the barge will be towed to another location to continue production. Each barge will measure 320 by 500 ft, approximately the size of four football fields, and will have the capacity to produce 1 million gallons or 2800 metric tons of methanol per day, from approximately 100 million cubic feet of natural gas per day (Fig. 4). The barges will use the highly successful "low- pressure" design developed by the Lurgi Company of Germany, a process proven in land-based methanol plants throughout the world during the last ten years. The decision to use Lurgi technology for "sea-trans- portable" methanol plants was based on the higher efficiency and greater operability of the technology compared to other commercially proven processes. The conversion plant will be designed to accept a wide variety of feed gas compositions, and will produce chemical-grade methanol for the broadest market base (Fig. 5). To minimize costs and construction time, the barge-mounted plants will be built in the high technology environment of a domestic or foreign shipyard. Selection of the construction site for each barge will be dictated by the location of the production site and by the relative construction costs. A number of shipyards have the capacity to build several barges per year. The detailed marine engineering to integrate the design of the processing plant with the floating platform can be performed by numerous major engineering companies around the world. Production Economics The barge-mounted plant concept not only assures large volumes of methanol, but it also keeps the overall production cost low by minimizing construction cost and providing access to low cost natural gas feedstock with no alternative or a negative value. Together, these advantages make the barge-mounted methanol plants economical today. The cost structure of a new barge-mounted methanol plant differs from that of existing methanol producers around the world (Fig. 6). For example, if a U.S. Gulf Coast producer is paying $4.70/MMBtu in 1985 for natural gas, the barge plant could afford to pay about $1.6O/MMBtu for gas and be able to deliver methanol to the Gulf Coast at the same price. At some future date such as 1990, a gas cost of $6.70/MMBtu for a domestic producer would have cost parity with about $3.60/MMBtu gas cost for the barge plant. In many foreign markets, feedstocks other than natural gas are used for methanol production (Fig. 7). For example, most of Japan's capacity is based on LNG while Western Europe uses residual oil or naptha. Because these feedstocks are substantially more ex- pensive than natural gas used by U.S. producers, the barge plants will compete even more favorably in these foreign markets. As crude oil prices rise, the value of methanol in each of these markets will increase. However, the hierarchy of methanol values in these markets should remain unchanged. Furthermore, the cost advantage for using methanol in these markets will improve as world energy costs increase since the value of remote gas should not escalate significantly.

Jan 1, 1982

By R. V. Norris

IRving Ariel Stearns died at his home, 60 South River St., Wilkes-Barre, Pa., on Tuesday morning, Oct. 5, 1920, of pneumonia, after an illness of about a month. In his death, the Wyoming Valley loses one oflits most eminent and best loved citizens, and the loss of so strong a participant in the activities of the Valley will leave a gap most difficult to fill. Despite his more than three score and fifteen years, Mr. Stearns, at the time of his death, was president of the Wilkes-Barre City Hospital, Wyoming National Bank, and the Wyoming Historical and Geological Society, chairman of the Board of the Vulcan Iron Works, and a director of the Spring Brook Water Supply Co., and of the Wilkes-Barre Lace Manufacturing Co. Mr. Stearns came of New England stock, a descendant in the eighth generation of Charles Stearns who was admitted freeman in Watertown in 1646. Irving Ariel Stearns was born Sept. 12, 1845, in Rushville, N. Y., a son of George W. and Miranda (Tufts) Stearns. He was graduated from the Rensselaer Polytechnic Institute of Troy, N. Y., in the celebrated Class of 1868. After graduation, he was assistant professor of chemistry in charge of the analytical laboratory for a year, then went to Wilkes-Barre in 1869, as engineer in the office of R. P. Rothwell, at that time the leading mining engineer of the region. From 1871 to 1872, he was superintendent of the McNeal Coal & Iron Co. of Schuylkill County, Pa. and in 1872 succeeded to Mr. Rothwell's business when the latter became editor of the Engineering & Mining Journal of New York. From 1872 to 1885, Mr. stearns was in private practice as a mining engineer, handling a great amount of business in the anthracite region, including the building of the bridges at Shickshinny and Pittston, and the surveying and mapping of many of the individually operated mines. His practice extended throughout the country, with numerous examinations and reports upon mining properties in Pennsylvania, Virginia, West Virginia, Arkansas, Colorado, California, Wyoming, Idaho and Utah; he was responsible for the design and execution of the Lehigh Valley Railroad Co.'s great Tifft Farm improvements at Buffalo, N. Y. including canals, docks, coal stocking plant, etc. He was commissioned Quartermaster of the Ninth Regiment, N. G. P., March 29, 1880, was promoted to Major on May 15, 1884, and resigned Apr. 1, 1885. He always retained his interest in the National Guard and was trustee and president of the Ninth Regiment Armory Association.

Jan 1, 1922

By R. V. Norris

IRving Ariel Stearns died at his home, 60 South River St., Wilkes-Barre, Pa., on Tuesday morning, Oct. 5, 1920, of pneumonia, after an illness of about a month. In his death, the Wyoming Valley loses one oflits most eminent and best loved citizens, and the loss of so strong a participant in the activities of the Valley will leave a gap most difficult to fill. Despite his more than three score and fifteen years, Mr. Stearns, at the time of his death, was president of the Wilkes-Barre City Hospital, Wyoming National Bank, and the Wyoming Historical and Geological Society, chairman of the Board of the Vulcan Iron Works, and a director of the Spring Brook Water Supply Co., and of the Wilkes-Barre Lace Manufacturing Co. Mr. Stearns came of New England stock, a descendant in the eighth generation of Charles Stearns who was admitted freeman in Watertown in 1646. Irving Ariel Stearns was born Sept. 12, 1845, in Rushville, N. Y., a son of George W. and Miranda (Tufts) Stearns. He was graduated from the Rensselaer Polytechnic Institute of Troy, N. Y., in the celebrated Class of 1868. After graduation, he was assistant professor of chemistry in charge of the analytical laboratory for a year, then went to Wilkes-Barre in 1869, as engineer in the office of R. P. Rothwell, at that time the leading mining engineer of the region. From 1871 to 1872, he was superintendent of the McNeal Coal & Iron Co. of Schuylkill County, Pa. and in 1872 succeeded to Mr. Rothwell's business when the latter became editor of the Engineering & Mining Journal of New York. From 1872 to 1885, Mr. stearns was in private practice as a mining engineer, handling a great amount of business in the anthracite region, including the building of the bridges at Shickshinny and Pittston, and the surveying and mapping of many of the individually operated mines. His practice extended throughout the country, with numerous examinations and reports upon mining properties in Pennsylvania, Virginia, West Virginia, Arkansas, Colorado, California, Wyoming, Idaho and Utah; he was responsible for the design and execution of the Lehigh Valley Railroad Co.'s great Tifft Farm improvements at Buffalo, N. Y. including canals, docks, coal stocking plant, etc. He was commissioned Quartermaster of the Ninth Regiment, N. G. P., March 29, 1880, was promoted to Major on May 15, 1884, and resigned Apr. 1, 1885. He always retained his interest in the National Guard and was trustee and president of the Ninth Regiment Armory Association.

Jan 1, 1922

One of the first all-hydraulic crawler drills in service at a US open-pit mine has significantly exceeded the penetration rates of comparable pneumatic crawler rigs, according to Atlas Copco Inc. Overall production with the hydraulic unit has been double that of pneumatic crawlers in use. The installation is at the Foote Mineral Co. surface mine at Kings Mountain, N.C., where the company is engaged in mining spodumene, a combination of lithium, aluminum, and silicates. The ore is found in pegmatite dikes, a tough and abrasive host rock with compressive strength of tip to 5800 kPa (40,000 psi).

Jan 9, 1978

By Takeyasu Ito, Mayumi Someno, Kazuhiro Goto

SINCE the pioneering work by Kiukkola and Wagner,1 many experiments have been reported on solid electrochemistry at elevated temperatures. However, the studies have been confined to experiments under isothermal conditions. One may conceive many situations under nonisothermal conditions. With two different temperatures T1, and T2 at the two electrodes, the electromotive force, E of a Galvanic cell will be expressed by the following equation under a steady state heat transfer in solid electrolytes of zirconia-lime and thoria-lime. E = ^ $ l&-dGO2+a(T2-Ti) [1] where tO2- is the transference number of oxygen ions in the electrolyte, Go, is the chemical potential of oxygen, and a is the coefficient of the thermoelec-tromotive force due to the temperature difference. The objective of the present study was to evaluate the coefficient of the thermoelectromotive force for zirconia-lime and thoria-lime under isobaric condition. The physical meaning of this coefficient is out of the scope of the present communication. The experimental cell assembly is schematically shown in Fig. 1. The zirconia-lime electrolyte tube and thoria-lime electrolyte tube were 8.0 mm OD and 5.0 ID, from commercial sources with chemical analyses of 94.8 wt pct ZrO2, 3.85 pct CaO, 0.83 pct SiO2, 0.25 pct TiO2, and 0.05 pct Fe2O3; and 95.0 pct ThO2, 4.0 pct CaO and rare earth metal oxides, respectively. The specific gravity was 5.5 g per cu cm for zirconia-lime and 9.8 g per cu cm for thoria-lime. Original powder size before shaping and sintering the tube was several microns for both electrolytes. The distance separating the two electrodes was 4.0 or 5.0 cm. Platinum wire of 0.5 mm diam was used for the electrodes. The temperature gradient was controlled by heating one electrode with a small heating coil of nichrome wire. The temperatures at the two electrodes were measured with two calibrated Pt-13 pct Rh:Pt thermocouples, directly contacting the two platinum electrodes. The atmosphere was either air or pure oxygen. The partial pressure of oxygen in air was considered equal at the vicinities of the two electrodes, with negligibly small thermal segregation in the gas phase. The difference of the chemical potential of oxygen was controlled only by the temperature difference at the two electrodes and not by the oxygen pressure difference. The temperature ranges were 600" to 1200°C for zirconia-lime and 850" to 1200°C for thoria-lime electrolytes. Fig. 2 shows the relation of the measured electromotive force and the difference of the oxygen chemical potential at the two electrodes for zirconia-lime and thoria-lime electrolytes. The electromotive forces in the figure were measured by a *0.05 mv potentiometer. The chemical potential difference was calculated by the following equations.'

Jan 1, 1970

By D. W. Frommer, M. M. Fine

Mineral dressing research showed that iron concentrates of commercial quality could be produced from the Pea Ridge deposit near Sullivan, Mo. Magnetic separation and flotation, on a laboratory scale, yielded concentrates ranging from 60.0 to 71.4 pet Fe at recoveries of 89.9 to 97.6 pct. Early in 1957 St. Joseph Lead Co. announced discovery of three new centers of iron ore deposition in east central Missouri.' The discovery resulted from exploratory drilling in the vicinity of a magnetic anomaly or high. A deep hole, drilled into the Pre-Cambrian porphyry to determine the cause of anomaly, penetrated a magnetite-rich deposit.' The magnetic surveys that revealed the anomalies were begun by the Missouri Geological Survey in 1929 and were continued into the 1930's.3 At that time an area in Crawford County known as the Bourbon magnetic high was located. A second anomaly, similar in size and intensity, was discovered about six miles to the northeast in Franklin County in the vicinity of Sullivan. This area was not studied in detail until the early 1940's. To determine the cause of the anomalies, the USBM drilled four holes at the Bourbon site in 1943-1944.4 The most productive hole penetrated four mineralized zones having a total thickness of 127.5 ft. These zones contained magnetite in rhyo-lite porphyry at depths between 1600 and 2000 ft. Additional iron ore below 2000 ft was considered a possibility at the time. Some years later, the USGS, Missouri Geological Survey, St. Joseph Lead Co., and others cooperated in sponsoring an aeromagnetic survey of the Bourbon-Sullivan area which resulted in discovery of a third high, about eight miles distant at Pea Ridge. This deposit, with an estimated reserve of 50 to 100 million tons of iron ore, is considered the main find, although other orebodies in the same general area are of definite interest.' When this discovery was announced, St. Joseph Lead also revealed plans to exploit the deposit jointly with Bethlehem Steel Co. A new corporation, Meramec Mining Co., was established, and 1962 was set as the target date for completing physical plant.2 Annual production goals of 2 million tons of beneficiated and pelletized iron ore were proposed. Preparation of the site for shaft sinking was begun in June 1957. Orebody and Character of Samples: Drilling to date has established the Pea Ridge orebody as a crescent-shaped pipe about 300 ft wide. Some drillholes were bottomed at 2800 ft in very good iron ore.6 he orebody is predominantly magnetite, although hematite and a mixture of hematite and magnetite occur in the upper areas and peripheral walls. Drillhole cores representing ore from different areas and depths of mineralization were grouped into composites for testing. These composites consisted of: 1) medium grade mixed hematite and magnetite, 2) high grade mixed hematite and magnetite, and 3) high grade magnetite. The medium grade ore came from three holes with depths of i350 to 1900 ft. The high grade mixed hematite and magnetite cores came from the 1790 to 2812-ft interval of one hole. Partial chemical analyses of the three samples, given in Table 1, reveal that all are excessively high in phosphorus and sulfur, and sample 1 is

Jan 1, 1960

By Earl G. Alexander, W. R. Runyan

The nature of silicon growths which form on amorphous silicon dioxide during epitaxial deposition in unmasked areas was investigated. Octahedral silicon crystals nucleate and grow on the oxide at pinholes, adjacent to foreign matter, and probably at oxygen-deficient sites. Generation of these oxygen-deficient sites on the oxide surface is shown to be thermody-namically favorable under usual deposition conditions. The conditions which affect saturation (SiCl4 concentration, flow rate, temperature) determine the number of sites on which silicon will nucleate and grow. Reaction product HCl is likely responsible for suppressing silicon growths on the oxide near exposed areas of silicon. Evidence is given that the oxide-silicon interaction occurs in hydrogen only and involves water as a transport agent. SINCE shortly after the first epitaxial layers of silicon and germanium were grown over large areas, efforts have been underway to grow selectively on specified portions of the surface. Such selective growth should be particularly applicable to monolithic integrated circuits. Usually the approach has been to use a mask to delineate the desired area,'-7 but the VLS methoda can also be used, and direct programmed atomic beam deposition has been suggested.9 The masking techniques may embody two forms: in one the mask is a material which can later be removed along with any growths attached to it; in the other, attempts are made to prevent growth on the mask, so that over a whole slice the only deposition that will occur is in the unmasked regions. The present work is concerned with only the latter case, and specifically with silicon. Joyce and Baldrey1 suggested the use of thermally grown silicon dioxide as a mask material and showed that for the proper choice of operating conditions (total flow, SiCl4 concentration, total deposition time, and temperature) spurious growth could be minimized and that if the deposition times were not too large, and the criteria not too stringent, a usable process occurred. Later Schnable et al 4 observed that after extended deposition times, during which most of the silicon dioxide became covered with growth, there was always a band of oxide around the exposed silicon area that was quite free of spurious silicon crystallites. This latter observation is particularly intriguing since it extends the hope that with proper precautions masking can be much more versatile than it presently is. EXPERIMENTAL PROCEDURE Silicon substrates oriented to within 1.5 deg of a (111) plane were prepared by etch polishing lapped

Jan 1, 1967

By Sylvain Pirson

THE number of seismograph field crews employed in the active survey of potential oil territories is still on the increase, owing to the ever pending threat of a shortage in the supply of crude oil. It is to be expected that for years to come the seismograph will be responsible for discovering many new oil fields, both in wildcat territories and in deeper formations, and that the seismographic campaign will go on unabated. Yet improvements in instrumental design, in the field and interpreta-tive techniques, are brought about year after year, and lead to the reshooting of areas many times surveyed previously. Notwithstanding the experience gained by the past eight years of active work in reflection seismographic surveys, the results given by this method of mapping deep formations have in many instances been at variance with the information subsequently obtained by the drill. To overcome this shortcoming, geophysicists have used closer spacing of the shot points and closer control of the depth points. The method dis-cussed here is being used actively in the Mid-Continent region and endeav-ors to reduce the interpretation work to a mere mechanical technique, leaving as little as possible to the opinion of the interpreter.

Jan 1, 1937

Four generations ago, the Mount Morgan ore deposit sustained the hurly-burly of frantic development common to the finding of a rich discovery. In this case, it was gold discovered in gossan capping on one of the hills of the Dee Range. The bonanza ore, like the flush of youth, has been spent. Today, one recognizes in this operation the orderly manner of the senior citizen, keeping up with the times and husbanding resources. As mining towns go, Mt. Morgan has an enviable situation. The approach is from Rockhampton, Qld, a peaceful, affluent agricultural and cattle center near the sea. To reach the mine, one goes 22 miles, first across farming country, passing orange groves and occasional children on horseback. The ascent into the Dee Range is winding and rapid. In the winter, the hills are green and Bougainvillaea and flowering yellow bracken grow wild on the hillsides. Around a bend, the brown waste terraces of the mine come into view, rising above the surrounding country. The top of the mountain has been sawed off and a deep pit sunk into the core. A little further on, around a few more curves, the town of Mt. Morgan is seen nestling comfortably in the hollows, reaching up the slopes.

Jan 10, 1964

By W. A. Tiller, J. P. McHugh

HE majority of liquidus and solidus surfaces in phase diagrams have been determined by the conventional cooling- and heating-curve techniques.' These techniques have two main shortcomings: 1) the solidus may be in considerable error due to the difficulty involved in completely homogenizing the solid and 2) the determination of liquidus and solidus in more than a two-component system does not enable one to determine tie-lines connecting the specific equilibrium solid and liquid compositions. However, in a recent paper by one of the authors,' a method was suggested whereby the liquidus and solidus surfaces plus tie-lines in an n-component system may be determined. This method utilizes a controlled solidification technique and assumes that interface equilibrium exists during freezing. The present work was undertaken with a twofold purpose; first, to determine the liquidus and solidus lines in the pseudo-binary system Bi2Te3-Bi2Se3 by heating- and cooling-curve techniques and, second, to determine the partition coefficients of Te and Se in the BizTe3-,Sex system by controlled solidifica- tion techniques. The two sets of results can be compared to test the accuracy of the controlled solidification method. EXPERIMENTAL I—The starting materials for this study were 997999 pct Bi, Te, and Se, obtained from the American Smelting and Refining Co. The compounds BizTe, and Bi2Se3 were each prepared by melting together stoichiometric amounts of the elements, followed by twelve zone-refining passes. This produced homogeneous bars of the compounds for use in the phase-diagram studies. The apparatus used to obtain heating and cooling curves is illustrated schematically in Fig. 1. The alloy samples were located in a graphite crucible placed in a stainless steel canister. The canister was supported in a heavily lagged pit furnace by a device which oscillated the canister about its vertical axis at a frequency of about 3 cycles per sec during heating and cooling-curve runs. The graphite crucible was designed to minimize the thermal coupling of the sample to the furnace. A thin graphite sleeve separated the alloy sample from the stainless steel tube that housed the thermo-

Jan 1, 1960

By S. K. Nowak

The lithium solubility limit in solid aluminum was determined by the use of micro-graphic techniques. The solubility limit thus established was shown to be a true equilibrium by checking the reversibility of AlLi phase precipitation and dissolution around the equilibrium temperature. The experimental results fit a straight line by plotting log N(LI) against 1/T. The metallurgical reasons explaining the lack of agreement among previous investigations are discussed. THE solubility limit of lithium in solid aluminum was determined by Shamray and Saldau1 by micrography and by Grube et al.' and also Voss-Kiihler- by measurement of electrical resistivity. Since the addition of lithium induces extremely small changes in the aluminum lattice, X-ray techniques could not be employed for this purpose; in fact, the addition of lithium does not cause an expansion of the lattice as might be expected from a consideration of atomic radii, but causes a small contraction from 4.040 to 4.037A3, 4 when the solvent aluminum is saturated with this element. An analysis of the results from previous investiga-tions'" shows that with improvement of investigation techniques the solubility limit tends toward a lower lithium content. Again, some of the author's own experimental results on the action of atomic hydrogen on A1-Li alloys seemed to indicate that the solubility of lithium should be much lower, i.e., about 0.3 pet at 300°C: instead of 1.15 pet, the lowest published value.4 For the foregoing reasons it was decided to investigate this problem. The aluminum and the lithium used for this purpose were of the highest purity. The lithium solubility limit was determined by metallographic techniques, in particular by the use of a reagent especially developed for the purpose of revealing the AlLi phase. The solubility limit thus determined was shown to be a true equilibrium by checking the reversibility of AlLi phase dissolution and precipitation around the equilibrium temperature. All of the experimental work was carried out in 1951 at the Centre d'Etudes de Chimie Metallur-gique at Vitry, France, under the direction of Georges Chaudron.

Jan 1, 1957

By C. E. Lesher

COAL has been fighting a rear-guard action since the last World War. The battle against competitive fuels has been largely guerilla warfare with more sniping within the ranks than of organized opposition. Oil and natural gas are the fuels that over these twenty odd years have driven coal backward and out of many profitable markets. Now, somewhat timidly, the coal industry is trying a new weapon; namely, Research, or let us more properly say, Organized Research. Engineers have been designing this weapon for many years, supported by those interested in coal, including some coal producers. A part of this pioneer work has been Fundamental Research, the Ph.D. kind that is over the heads .of most of us. Another part has been aimed at immediate objectives and realizable profits, the practical, man-in-the-street sort. That is Industrial Research. Enough has been accomplished to make a fair exhibit, but whether this new weapon will have sufficient fire power to rout the opposition, whether the industry will really go into production and use it, the next few years will tell. NEED FOR COAL RESEARCH To utter "Research" is to use the modern magic word; to conjure up the miraculous-rubber from weeds; radar; magnesium from sea water; yes, even gasoline from coal. Research is a very general term. It means something different to every man. What is the coal industry seeking with its research; or what should it seek? And, specifically, how is it going about the job; and is it taking the best way? There are many who say that Coal has been asleep at the switch, while Oil and Gas have been taking the energy business. In an organized way this is true. Large-scale, privately financed research is just started in the Pennsylvania, anthracite industry, and it is still a dream for bituminous coal. What has been done so far collectively is purely defensive; as, for instance, to improve mechanical devices for burning coal so as to be able to recover markets for house-heating fuel long since abandoned to oil and gas. To appreciate just how seriously bituminous coal has slipped back in the national economy in the past 25 years, one has only to recall that, in the last war the Navy required for its operations all the high-grade, low-volatile coal that could be produced, and that anthracite was withdrawn from the middle and northwest markets to keep the eastern seaboard warm. All coal was "rationed" by zones, if not to individuals. Now the Navy, the Armed forces and the Merchant Marine are propelled by oil and gasoline. Gasoline and heating oil are rationed to individuals. Production of all coal in this country in 1918 reached the historic figure of 678,200, 000 tons, and in 1943, after 25 years, it is expected to reach a special wartime total of 660,000,000 tons. Meanwhile, production of crude oil this year may exceed 1,500,000,000 bbl., and like that of natural gas, reach four times the amount produced in 1918.

Jan 1, 1944

By William Blauvelt

THE type of gas producer in which the ashes are fluxed and run off as slag was among the very earliest made. Ebelmen built the first one in 1840 at Audincourt, France, only a year after the installation of the first gas producer of which we have record. Charcoal was used as the fuel, with blast-furnace slag and clay is flux. My interest in this type of producer began when as a boy I saw the fluxing producer at Chester, N. J., which was invented by W. J.. Taylor, and described by him in 1881.1 This producer was invented independently by Mr. Taylor to meet the difficulties he experienced in making producer gas for roasting sulphurous iron ores. It will be of interest to review briefly his description of his producer. It was built like a small blast furnace, having a hearth 24 in. in diameter and 24 in. high. The bosh angle was 25° from the vertical; the diameter at the bosh 4 ft. and at the top 3 ft.; the total height 12 ft. The producer contained one water-cooled tuyere 12 in. above the bottom, with a 1.5-in. nozzle.. Depth of the coal above the tuyere; 6 ft. Mr. Taylor mixed the coal with from 30 to 40 per cent. of basic blast-furnace slag to flux the ash. Occasionally some limestone was also used, but never limestone alone, as the use of the furnace cinder gave a larger volume of slag and made it easier to maintain a proper fluidity. . The producer was blown with a small Weimer blowing engine, delivering 300 ft. of air per minute, at from 1 to 1.5 lb. pressure. The slag was tapped every 2 hr. and was black and glassy in appearance. Broken or egg size anthracite was used. The fine sizes of anthracite could not he made to work. Mr. Taylor expressed the belief that bituminous coal could be used if not too fine, but no experiments were made with this coal. Runs were made of four weeks' duration, with no stops or changes. Mr. Taylor reported the following advantages:

Jan 12, 1913

By Robert L. Zook, Bernard J. Olup, James J. Pierre

Coal refuse slurry impoundments are dams constructed of coarse coal refuse to impound fine refuse (slurry) and water (25 to 30% solids). Both products are waste from coal preparation plants. A number of these structures in West Virginia, Pennsylvania, and Kentucky were investigated to determine embankment stability. During the investigation a variety of embankment designs were encountered. The investigation determined the soil and geological characteristics of the embankments and the sites. This was accomplished by a test drilling and monitor installation (observation wells and piezometers) program, geologic study, and large-scale mapping which allowed subsurface profiles of the embankments to be constructed. The laboratory testing program concentrated on textural classification of the coal refuse, permeability, and determining strength parameters to be utilized in the stability analyses. For the stability analyses, the modified Fellenius slip circle, simplified Bishop slip circle, and analysis for translational failure were utilized. In all stability analyses hydrostatic pressure and seismic acceleration probability were considered. This investigation indicated that 62% of the embankments analyzed were in a stable condition. The coal seam, the type of roof rock, and the gradation of the refuse influence the degree of compaction obtainable and the permeability of refuse. The shear strength of coal refuse appears to be controlled by its composition, moisture content, degree of compaction, amount and grain size of fines present. This investigation demonstrated these embankments should not be treated as pure state-of-the-art dams consideration must be given to the particular properties of coal refuse and the total refuse disposal system. Refuse dam slurry impoundments generally lack the site selection phase that is standard practice with siting most other types of dams.

Jan 1, 1976

By J. B. Newsorn

VERTICAL SHAFTS in the United States have heretofore been sunk by blasting and mucking. The blasting leaves uneven, shattered walls which usually must be supported. Even though the walls will stand, shaft lining is needed to furnish supports for the cage guides, pipes, and power conduits. The lining is generally timber, and as timber can be most easily framed into rectangles, rectangular shaft openings are the rule. The timber reduces the size of the cage floor. For example, if the Idaho Maryland company had put down No. 2 shaft by blasting and mucking, the cage area would have been about thirty per cent of the total shaft area. Besides a low percentage of useful area, an ordinary shaft is subject to fire hazard and to timber maintenance charges. It is also poor for ventilation because the timber ribs cause eddies which greatly reduce the speed of the air currents. A bored shaft does not have these disadvantages. The walls are smooth, circular, and not shattered by blasting, so lining is not required in most

Jan 1, 1936