Search Documents

By L. K. Jetter, C. J. McHargue

The use of axis charts for representing the texture of cold-rolled thorium sheet was compared with conventional pole figures. Four texture components were deduced from the axis charts and shown to be consistent with the pole figures. It was shown that consideration of the pole figures alone could lead to an apparent component which is the average of two actually present. It was also shown that the spread about the "ideal" textures and the amount of material associated with each could be readily obtained Fom the axis chart method. BECAUSE of the crystallographic nature of the deformation mechanisms in metals, plastic flow results in the alignment of certain crystallographic directions with the primary flow directions. In the study of the "preferred orientation" thus developed, one wishes to discern the distribution of the crystallographic directions with respect to some reference direction, usually a direction related to the fabrication procedure, such as the rolling direction. The pole-figure method, introduced by ever,' involves the plotting of the distribution of the poles of some family of planes on a stereographic projection which places the reference direction(s) at the north pole and/or in the center. By noting the angles between the reference directions and concentrations of poles on several such pole figures, one can deduce the crystallographic directions which are aligned with the reference directions. If the preferred orientation is relatively simple and well-developed, one to three pole figures may be sufficient for obtaining the desired information; if there are several texture components, more pole figures may be needed. A significant improvement in the method of representing the textures in wires and rods resulted from the introduction of the "inverse pole figure" or axis-distribution chart by Harris.2 Such a chart gives directly the distribution of the reference axis relative to the standard stereographic projection. There has been widespread acceptance of this method for the representation of fiber textures, and methods have been proposed for converting observed diffraction intensities into axis densities.2-6 The suggestion by Mitchell and Rowland3 and Jetter, McHargue, and williams5 that sheet textures could be represented as distributions of rolling, normal, and transverse directions have been criticized on the basis that they offer no significant advantage over a combination of two ordinary pole figures and that it has not been proved that sheet textures can be treated as quasi fiber textures.6 If the purpose of a texture determination is to study some property which is related to the orientation of a particular crystallographic plane or direction, then conventional pole figures certainly are sufficient. For example, the distribution of the slip planes in face-centered cubic metals (the (111) pole figure) serves to indicate the variation in mechanical properties of sheet. On the other hand if the study is directed at an understanding of the factors influencing texture formation, it is desirable to know not only the preferred orientation but the kind and degree of spread from it and the relative amounts of material in each component, if there are more than one. Axis charts give this information as well as the orientation distributions. Consider the procedure for deducing a texture component from a pole figure for the (111) planes

Jan 1, 1961

By Benjamin C. Craft

As predicted, during 1937 South Louisiana witnessed one of the most active drilling campaigns in the history of the area, resulting in the discovery .of 14 new fields. The economic importance of 10,000-ft. production was far-reaching and the objective depths placed on some wildcats was 12,000 feet. Most of the important discoveries and deep tests were in the delta area between the Atchafalaya and Mississippi Rivers, where the upper Miocene sands were found productive between 10,000 and 11,000 ft. The casing program on these wells usually called for a protection string of 95/8-in. casing at approximately 9500 ft. Drilling barges with the heaviest equipment were used where water transportation was available. The oil production for South Louisiana during 1937 was 62,147,690 bbl., as compared with 51,968,727 bbl. during 1936, an increase of 19.5 per cent. There were 281 oil and gas wells and 172 dry holes completed during 1937 as compared with 262 oil and gas wells and 135 dry holes during the previous period. New Fields Gibson.—The first discovery for the year was in the Gibson area, where Shell Petroleum Corporation's Realty Operators No. 1, sec. 18, 17 S., 15 E., Terrebonne Parish, was completed flowing 780 bbl. of 38° A.P.I. oil daily through a 14/64-in. choke with a tubing pressure of 1700 lb. Production is from upper Miocene sand found from 9461 to 9483 feet. Abbevil1e.—The discovery well for the Abbeville field was Continental Oil Company's Hebert No. 1, sec. 20, 12 S., 3 E., Vermilion Parish, completed flowing 50 bbl. of distillate and 2 million cubic feet of gas through a 3/16-in. choke with a tubing pressure of 2550 lb. The well was plugged back from 12,216 ft. in the Chickisawhay, and is producing through perforations from upper Miocene sand found from 7668 to 7682 ft. Later in the year, the same operators completed Brookshire No. 1, sec. 66, 12 S., 3 E., flowing 366 bbl. of 42° A.P.I. oil per day through a 3/16-in. choke with a tubing pressure of 1800 lb. This well was com-

Jan 1, 1938

By George Smith

The Australian Broken Hill Consols mine is situated within a third of a mile eastwards of the famous Broken Rill Proprietory mine; but, so far as has yet been proved, the respective lodes have no connection whatever. The Proprietory line of lode, striking N.E. and S.W., is coincident with the bedding-planes of the inclosing gneiss, and, according to Mr. E. F. Pittman, A.R.S.M., government geologist, is undonbtedly a saddle-formation. This opinion, which met with much opposition at the time it was advanced, is now, I understand, being generally confirmed as the work of development opens out fresh areas for observation along the line of lode. The lode is of immense thickness—in places over 300 feet and though it has been found to contain sufficient quantities of secondary silver compounds to yield phenomenal outputs of silver, its principal constituents are various lead and other ores, and it would appear more correct to regard it as an argentiferous lead-deposit than as a silver-lode proper. The Consols lode differs from its gigantic neighbor in every respect. With an average thickness of not more than 18 inches, it has been worked along its course for upwards of 1300 feet, and at every point yet explored has been found remarkably well-defined and persistent. With a strike E. and W., it cuts obliquely across the bedding of gneiss and schist, continuing uninterruptedly through various bands of eruptive amphibolite. The dip, which is to the south, ranges from 24 near the surface to nearly vertical in the lower levels; but the alteration is not regular, as in places the lode is almost flat, and this at a vertical depth of over 300 feet. These changes of inclination have had no effect on the ore-deposits, which, as I shall endeavor to show, have been governed entirely by " cross-

Jan 1, 1897

By A. F. Witt, A. M. Gaudin, A. K. Biswas

Finite contact angles in the rutile-water-organic liquid system are traceable to contamination or are due to addition of a surface-active agent. Finite contact angles are invariably accompanied by hysteresis.1-7 Besides surfactant concentration and pH, the nature of the organic liquid is found to be a factor influencing the magnitude of contact angle hysteresis. In a recent paper the authors have reviewed principles and applications of measurement methods for contact angles and their hysteresis.22 In this paper, these methods are applied to a system consisting of rutile, an organic liquid (benzene, decane, or dode-cane) and water. Surfactant (dodecylamine hydro-chloride) was used at various concentrations and various pH values. MATERIALS A synthetic rutile crystal supplied by the Linde Co. was used. It is a cylinder 1/2 in. diam, with faces cut perpendicular to the c-axis. The crystal is stated to be alumina-free and to be 99.9% pure. Rutile is a high surface energy solid, its calculated average field strength being 2.7 x 105 e.s.u.,9 its dielectric constant10 is 114. The zero point of charge of rutile was measured11 and found to be at pH 6.0. The atomic distances and bond angles of the tetragonal crystal of rutile have been precisely determined.l2 The organic liquids were specially purified. Reagent grade benzene was repeatedly shaken with concentrated sulfuric acid to remove thiophene, then neutralized with sodium hydroxide solution, rinsed with distilled water, dried overnight over anhydrous calcium chloride and filtered. The refractive index of this chemically purified benzene was 1.4977 (at 25°C) - very close to that of pure benzene (n25 1.4979).13 Both n-decane and n-dodecane were washed with aqueous sodium hydroxide, concentrated sulfuric acid (repeatedly, until the acid layer was colorless) and again with alkali, to free the organic hydrocarbon from fatty acids and unsaturated hydrocarbons. The organic phases were subsequently washed with distilled water and dried over anhydrous sodium sulfate. The filtered hydrocarbons were then distilled under vacuum (9-10 mm pressure). Decane, thus purified, showed traces of unsaturated and of carboxylic compounds. On gas chromatographic analysis the purified n-dodecane showed the presence of two impurities. However, the relative retention times of these components did not change substantially when measured on a polar or a nonpolar column. This indicates that the compounds were probably in the same polarity class, i.e. the components were nonpolar like dodecane. Conductivity water has always been one of the liquids. Conductivity of the water used was 10-6 ohm-' cm". Dodecyl ammonium chloride was prepared from pure amine (supplied by Armour and Co., Chicago), by Li in the MIT Mineral Engineering Laboratory.14 The critical micelle concentration at 25°C is known, 0.0138 mol per liter15 or 3.06 gpl. All our experiments have been done at concentrations lower than the critical micelle concentration. The glass vessels, glass drop holder and the rutile crystal were all cleaned with hot chromic acid followed by distilled water, concentrated hydrochloric acid, and again distilled water, and conductivity water. During the experiments, a nitrogen atmosphere was maintained. For this purpose, commercially purified nitrogen was further purified by passing it over hot copper wire at 450°C, then through columns of acidic chromous chloride solution, concentrated alkali solution and distilled water. APPARATUS AND METHODS Hysteresis was produced by the "captive drop" or constant volume drop method as well as by the "expanding-contracting drop" or variable volume drop method. The image of the drop while it is expanding, contracting or moving is projected on a screen and photographed. The developed film is projected through an enlarger and the contact angles measured with a protractor.

Jan 1, 1964

The annual report f the Secretary of the Navy for the fiscal year, ending June 30, 1917, but including operations and recommendations up to Dec. 1 of that year, contains the following remark about the activities of the Naval Consulting Board. The members of the Institute who are members f this Board are William L. Saunders, Benjamin B. Thayer, Thomas A. Edison, Thomas Robins, Lawrence Addicks, Joseph W. Richards, W. R. Whitney, assisted by 47 other members f the Institute, in the capacity of associate members of the Naval Consulting Board. During the year, the work of this board, organized and approved by Congress in 1915, has increased very materially in importance and volume, its meetings have been frequent and the work of its individual members has been such in some cases as to occupy almost their entire time in the service of the Government. Some time before the active entry of this country into war the board called a special meeting to which were invited some 50 of the leading scientists and industrial managers, whose special study fitted them to advise on the methods of meeting the

Jan 2, 1918

(Members are urged to send in for this column any notes of interest concerning themselves or their fellow-members.) Members who registered at Institute headquarters during July and August : R. H. Sweetser, Columbus, Ohio. C. R. Hill, New York, N. Y. Raymond Brooks, Goldfield, Nev. H. A. Morrison, Candor, N. C. Edward M. Shepard, Springfield, Mo. Frederick J. Patchell, Washington, D. C. Rudolf Gahl, Clifton, Ariz. Walter F. Pyne, New York, N. Y. Edmund von Maltitz, Pittsburg, Pa. Harvey B. Small, Mangangue, Colombia, S. A. M. K. Rodgers, Seattle, Wash. M. B. Cohen, Miami, Ariz. J. F. Erdlets, Jr., New York, N. Y. A. P. Watt, Newark, N. J. D. H. Ladd, Houghton, Mich. H. H. Stoek, Urbana, Ill. Roy F. Cornell, Santa Cruz, Cal. D. W. Brunton, Denver, Colo. W. B. Foote, Geneva, N. Y. C. S. Robinson, Youngstown, O. H. Sjogren, Stockholm, Sweden.

Jan 9, 1913

By Walter J. Karplus, Otto J. M. Smith

The transient response of earth formations may be tlcter.171ined by means of four electrodes mounted coli-rienrly on n sonde. Exponentially decaying current pules are applied to one pair of electrodes and the re.rrrlting voltage transient at the other pair is recorded. It is shown by theoreticol analysis and verified by laboratory experiments that this arrangement readily yields the direct resistivity of the formation and provides valrrable additional information as well. INTRODUCTION Although electrical transients have been employed with moderate success in geophysical prospecting, their application to well logging has received virtually no attention in technical literature. In the conventional direct resistivity logging methods only the zero frequency impedance of the formation under study is measured, and no information is obtained regarding its reactive characteristics. Since the use of certain transients appears to offer some advantages in this respect, experiments were performed on a laboratory scale to investigate this possibility. This investigation was limited to a study of a four-electrode array where both the receiving and transmitting electrode pairs are mounted on a logging sonde, and decaying exponential pulses are applied to the transmitting electrodes. THEORY Given an electrode configuration as shown in Fig. I, located in a homogenous medium of resistivity p, if each electrode has an effective radius, r, which is small compared to the spacing, s and a, it is easy to show by integrating the volume resistivity that the input resistance, Rrw, of the transmitting electrodes is Rxw=p/2pr If a capacitor of capacity C, charged to a voltage Em, is suddenly connected to these electrodes, the resulting current, I(t), will then be The voltage transient, E(t), at the receiving electrodes may then be found by substracting the resulting potential at electrode Y from that appearing at electrode Z. and by inserting Eqs. 1 and 2 Integrating Eq. 4 with respect to tim

Jan 1, 1957

By M. R. Geer, H. F. Yancey

0. R. LYONS*—I know that we are all interested in hearing about problems that other people have. To most of the people from the eastern part of the United States, this kind of coal preparation is completely different. It represents washing difficulties that most operators have never experienced, or, if they have, they have refused to consider them because there are coals that are much easier to wash and, therefore. they leave the more difficult ones alone for the time being. E. R. McMILLAN†—I think the au-thors have summarized the material very well. Dr. Yancey has spent a great many years in the study of washing coals, as has Mr. Geer. I might comment briefly on some of the plants that were mentioned, plants with which I have had some con-nection, particularly those of our own company, the Northwestern Improve-ment Co. I would like to point out this: that ill each case, a great deal of work was done in the way of preliminary studies of washability of the coal before plants were built. The first plant of any size built in Roslyn field was mentioned in the paper. This central cleaning plant was designed and built to handle coal from three different mines. I might say that prior to 1935, the year in which the plant was built, the coal was used largely as railway fuel, close to a million tons annually. But as mining increased in depth, it became increasingly difficult to separate and gob much of the impurities underground, with the result that the run-of-mine coal became so high in ash that the railroad eventually was forced to consider installing some kind of preparation plant at the mine. We spent about a year in preliminary studies in cooperation with the Bureau of Mines to find out the best type of plant that would clean the coal. The result, as Mr. Geer has explained to you, is a rather complicated plant, but it is doing a very satisfactory job. We have, however, made a number of changes and improve-n~euts since it was first built. The last addition was the, installation of a cen- trifugal drier to dewater the minus ¼ in. size. We are now contemplating installing heat driers for further drying of minus ¼ in. We use Vissac heat driers for drying the stoker coal, the ¾ to in. The demand for drier coal, for both railway and industrial use, is forcing us to further drying of the coal. The plant that was mentioned as having been built in Pierce County, during the war, was a government sponsored plant. I happen to have had some connection with its design, construction and initial operation. We did what we thought then, and still think, was a very thorough job of preliminary studies in cooperation with the Burea of Mines of the coal from that field. The plant was as good a plant as could be built with the equipment available at that time, 1943. The plant that was mentioned as having been built at Ravensdale for treating the McKay coal was rebuilt about two years ago, and in addition to the modified Elmore jig washer that was mentioned. we added a coucentrating table for re-cleaning the minus 3/32 in. Our object there was to produce a commercial

Jan 1, 1950

The engineering personnel shortage, present and impending, so well brought out in the article in Mining Engineering in the August, 1951 number, both in the editorial lead and the article by William B. Plank and Henry J. Petrie, has left untapped and has ignored a potential source of supply that would fill the need ably and with complete satisfaction. This source is comprised of the women engineers- and geologists, both presently, trained and able to handle work at all levels, and the many who would make splendid engineers and geologists if they could hope for even a modest taste of the square deal that should be theirs, but, as we all know, is not. I write from experience. It is not pleasant or sensible to have to urge borderline cases among men students to consider engineering and geology as careers to fill the need, when I have far more able, interested and suited young women students whom I must divert into other channels. It does not make sense to scrape the bottom and sides of the barrel to induce potentially second or third rate male engineers and geologists to enter the profession when we have superior material among the women, eager to do good work in these fields. It does not make sense for these men to become second or third rate in these fields when they might be first rate salesmen, musicians, advertising copywriters or policemen. Nor does it make any more sense to force potentially first rate female geologists and engineers to become second or third rate and very frustrated typists, kindergarten teachers, dress sales-women or clerks. At this point I am willing to admit that where superstitious -miners object to women in underground workings, men are available for the jobs. Moreover, it is not necessary for women to be sent into the most difficult country, if there is reluctance on either side of the contract. There may be fewer of them eager for the roughest assignments, in proportion to the men, but women are so accustomed to discrimination far more complete than that against any racial or religious group, that a reasonably tough assignment would seem like a heaven-descended joy. In my own experience, I have found that my girl students majoring in geology, could keep up with me in the field in the roughest terrain, but. the men, all but the best students and the most physically fit young men, complained that they could not keep up with me and that I always "walked their-legs off. The women, a few men and I always returned with bags heavy with well chosen specimens and proper notes. Most of the men carried no specimens and-but poor scraps of notes on loose bits of paper. Yet the men were urged to prepare for a career in engineering or geology if their examination marks were reasonably good. When we find that we still have a shortage of engineers and geologists, after putting all the qualified women to work, then we may begin to worry. Until then, we are simply fooling ourselves as we wander in, a forest of outmoded tradition and emotional habit reactions. MARY W. GARRETSON ASSOC. MEMBER, AIME SCARSDALE, N. Y.

Jan 1, 1952

By C. L. Dake

Iron is much more soluble in the ferrous than in the ferric form. Where, as in the case of the ferrous silicates and. the sulphides, the iron is already in the ferrous form, it may go at once into solution and be removed, upon the breaking down of the parent rock. If in the ferric form, it must first be reduced; usually by the decay of organic matter, the demand of the decaying carbonaceous matter for oxygen being so great that the latter is abstracted from the ferric compounds and the iron is thereby reduced and rendered soluble. The iron may go into solution as the sulphate, or in the presence of excess CO2 as ferrous carbonate. It is probably soluble as salts of the organic acids.' Recent work indicates that these are important in the formation of bog ores.2 There is considerable variety of opinion concerning the behavior of these organic compounds.3 The secretions about the roots of plants and trees also cause the solution and removal of iron and a consequent bleaching of the soil,4 While the matter is not yet well understood, we can probably say definitely that the so-called organic acids are a group of colloids which possess slightly acid properties, and the salts of which are partly soluble and partly insoluble.5 Their iron salts readily change from the ferrous to the ferric form, and their solubility is greatly modified by the presence of ammonia.

Jan 1, 1916

By M. C. Udy, P. C. Rosenthal

The use of minute boron additions to steel has been given considerable attention in recent years. Comparisons made between boron-free and boron-containing heats of otherwise identical analysis have indicated, beyond a doubt, the potent effect of boron for increasing hardenability. The actual hardenability increase has been expressed as a multiplying factor, or in terms of the percentage of other alloying elements boron might replace. The present study presents the results of a systematic survey of the use of boron as an addition to two types of alloyed steels and as a replacement for various percentages of molybdenum in these steels. Both cast and wrought steels of the two basic compositions were prepared. Molybdenum, because of its scarcity at the time the investigation was started, was selected as the element to be replaced by boron. Attention was also given to the effects of boron on other properties of the steels, particularly their notched-bar toughness, to investigate other advantages or limitations of this element as an alloy addition. Experimental Work Steels Investigated The two basic compositions used in this survey of boron as a replacement for molybdenum are given in Table I. The cast steels were higher than the wrought steels in silicon content to improve the casting quality. Table i.—Nominal Composition of the Two Base Alloy Steels composition. Per Cent. steel Mn Si Ni Cr Xi-Cr-Mo Wrought 0.28-0.70-0.15-o.45—o.45-0.32 0.90 0.25 0.55 0.55 Cast 0.28-0.70-0.35-0.45-o.45- 0.32 0.90 0.45 0.55 0.55 hln-&lo Wrought 0.28-I .go-o.0.15-0.32 1.70 0.15 Cast o. 28- I.40- 0.35- 0.31 1.70 0.45 a Sulphur was 0.040 per cent maximum and phosphorus 0.030 per cent maximum. Each of these base steels, both cast and wrought, was made with molybdenum contents of o, 0.10, 0.20, 0.30, or 0.40 per cent, the total comprising 20 steels. In addition, each of these 20 compositions was prepared with boron additions in amounts of o.oo15, 0.003, and 0.006 per cent as ferroboron; and in amounts of 0.002 and 0.005 per cent as two commercial intensifier alloys, designated alloys A and B. The boron-treated steels totaled 100, and the entire series 120. Test Procedure Each steel was melted as an individual heat in a 50-lb., magnesia-lined induction furnace. Ingot iron scrap or mixtures of ingot iron and steel. scrap were used for melting stock. Deoxidation was carried out in the furnace with 0.10 per cent aluminum. The aluminum addition was

Jan 1, 1948

By M. C. Udy, P. C. Rosenthal

The use of minute boron additions to steel has been given considerable attention in recent years. Comparisons made between boron-free and boron-containing heats of otherwise identical analysis have indicated, beyond a doubt, the potent effect of boron for increasing hardenability. The actual hardenability increase has been expressed as a multiplying factor, or in terms of the percentage of other alloying elements boron might replace. The present study presents the results of a systematic survey of the use of boron as an addition to two types of alloyed steels and as a replacement for various percentages of molybdenum in these steels. Both cast and wrought steels of the two basic compositions were prepared. Molybdenum, because of its scarcity at the time the investigation was started, was selected as the element to be replaced by boron. Attention was also given to the effects of boron on other properties of the steels, particularly their notched-bar toughness, to investigate other advantages or limitations of this element as an alloy addition. Experimental Work Steels Investigated The two basic compositions used in this survey of boron as a replacement for molybdenum are given in Table I. The cast steels were higher than the wrought steels in silicon content to improve the casting quality. Table i.—Nominal Composition of the Two Base Alloy Steels composition. Per Cent. steel Mn Si Ni Cr Xi-Cr-Mo Wrought 0.28-0.70-0.15-o.45—o.45-0.32 0.90 0.25 0.55 0.55 Cast 0.28-0.70-0.35-0.45-o.45- 0.32 0.90 0.45 0.55 0.55 hln-&lo Wrought 0.28-I .go-o.0.15-0.32 1.70 0.15 Cast o. 28- I.40- 0.35- 0.31 1.70 0.45 a Sulphur was 0.040 per cent maximum and phosphorus 0.030 per cent maximum. Each of these base steels, both cast and wrought, was made with molybdenum contents of o, 0.10, 0.20, 0.30, or 0.40 per cent, the total comprising 20 steels. In addition, each of these 20 compositions was prepared with boron additions in amounts of o.oo15, 0.003, and 0.006 per cent as ferroboron; and in amounts of 0.002 and 0.005 per cent as two commercial intensifier alloys, designated alloys A and B. The boron-treated steels totaled 100, and the entire series 120. Test Procedure Each steel was melted as an individual heat in a 50-lb., magnesia-lined induction furnace. Ingot iron scrap or mixtures of ingot iron and steel. scrap were used for melting stock. Deoxidation was carried out in the furnace with 0.10 per cent aluminum. The aluminum addition was

Jan 1, 1948

By Eric Jette

THE alloys of gold and iron were investigated in 1907 by Isaac and Tammann,1 who determined the thermal diagram for the entire system by thermal analysis and microscopic examination. They also reviewed the previous literature. Since that time the present authors have been able to find only two additional references. Guertler and Schulze2 examined the electrical resistance of iron alloys containing up to 40 per cent by weight of gold between 0° and 200° C.; the alloys were in the form of wires. The main result of this work was to confirm the solid solubility limit found by Isaac and Tammann; namely, about 20 per cent Au. More recently, Shih3 has examined the magnetic properties of gold alloys containing up to 10 weight per cent iron and particularly the range below 5 per cent. The alloys in the lower range were found to be paramagnetic; the 10 per cent alloy was ferromagnetic. The present investigation was undertaken to determine the solid solubility limits at various temperatures, particularly below the a-y transformation point of iron, since these solubilities are of some impor-tance in connection with the working of the alloys in the manufacture of certain "grey" and "blue" golds.

Jan 1, 1934

By R. Maddin

IN analyzing the relation between the orientation of new grains and that of the deformed matrix of axially extended and recrystallized single crystals of face-centered cubic metals, a two-stage rotation process" is generally used where the first rotation is made in order to account for an "adjustment of orientation to the environment of strain."&apos; It has been argued that in spite of the difference of orientation, which may amount to as much as 12" (in a brass),&apos; between the octahedral plane as observed in the parent lattice and in the recrystallized grain, it is believed to be a common plane in the sense that it constituted the nucleus in the parent strained crystal from which the new grain grew.&apos; A possible source of the deviation in orientations of a common pole in the new grain and that of the deformed single crystal matrix from which it has grown may be found in the distribution of strain resulting from the plastic deformation. It might be expected in view of the incongruent nature of shear&apos; that the perfection of the octahedral plane along which glide has occurred is disrupted and that this disruption constitutes the strain from which nuclei of new grains can grow during recrystallization. Evidence for the existence of strain along glide planes was first detected by Taylor" in 1927 and substantiated by Collins and Mathewson&apos; in 1940. In their investigations, however, the deformed single crystalline specimens (aluminum) were cut mechanically along the glide planes followed by mechanical polishing. X-ray exposures (glancing angle) of only 8 min with filtered radiation were used. It was later shown&apos; that this type of surface preparation did not remove with all certainty the mechanically disturbed surface. It was felt that a re-investigation of this phenomenon using more refined techniques might reveal a more correct extent of the strain resulting from the deformation which might correlate the deviation of the common pole of the recrystallized grain with the acting slip plane of the matrix crystal. In accordance with these thoughts, a single crystal of a brass (70/30 nominal composition) M in. in diam x 5 in. long, tapered as in previous experiments,&apos; was extended and carefully documented with respect to elongation and shear. Disks about % in. thick paralle&apos;l to the primary slip planes were cut from the specimen by means of an etch cutter." These disks represented volumes of the specimen which had been extended 0, 5, 10, 15, and 20 pct. Copper Ka monochromatic radiation was obtained by reflecting 35,000 v copper radiation from the c-cleavage face of a pentaerythritol crystal. The monochromatic radiation was collimated and led on to the disk set at the proper 0 angle for reflection from the primary (111) planes. The monochromatic beam was aligned in a plane containing the active slip direction. Following a 10 hr exposure at the theoretical Bragg angle, the disk was reset at 0 + 1°, 0 — 1", 0 + 2", 0 — 2", etc., until no Bragg reflection was obtained. The disk was then rotated 90" about its polar axis, and the same X-ray procedure was used. The results are shown in Table I. It may be seen from the results in Table I that the plastic deformation (20 pct elongation) produces fragments of the glide plane which are rotated or tilted as much as 25 " from the normal position on a purely block slip model. In addition to the large variation in 0 angle in the slip direction, there is a variation in 0 as much as 20" in the direction at right angles to the direction of slip, i.e., <110>. In view of the results shown, it may now be argued that the strain distribution finds its origin in the incongruent nature of the slip process.&apos; The use of the two-stage rotation process seems valid in attempting to explain the relation between the orientation of recrystallized grains and the matrix from which they have grown. Acknowledgment This work was sponsored by the ONR under Contract Number N6 onr 234-21 ONR 031-383. The author would like to thank N. K. Chen for reading and correcting the manuscript. References &apos;R. Maddin, C. H. Mathewson, and W. R. Hibbard, Jr.: The Origin of Annealing Twins. Trans. AIME (1949) 185, p. 655; Journal of Metals (September 1949). &apos;J. A. Collins and C. H. Mathewson: Plastic Deformation and Recrystallization of Aluminum Single Crystals. Trans. AIME (1940) 137, p. 150. eN. K. Chen and C. H. Mathewson: Recrystallization of Aluminum Single Crystals After Plastic Extension. Unpublished. 4 C. H. Mathewson: Structural Premises of Strain Hardening and Recrystallization. Trans. A.S.M. (1944) 38. :&apos;C. H. Mathewson: Critical Shear Stress and Incongruent Shear in Plastic Deformation. Trans. Conn. Acad. of Arts and Science, (1951) 38, p. 213. "G. I. Taylor: Resistance to Shear in Metal Crystals, Cohesion and Related Problems. Faraday Soc. (1927) 121. &apos;R. Maddin and W. R. Hibbard, Jr.: Some Observations in the Structure of Alpha Brass After Cutting and Polishing. Trans. AIME (1949) 185, p. 700; Journal of Metals (October 1949). &apos;R. Maddin and W. R. Asher: Apparatus for Cutting Metals Strain-Free. Review of Scientific Instruments (1950) 21, p. 881.

Jan 1, 1953

The mining fraternity of North America was grieved and shocked to learn of the death of Dr. Willet G. Miller on Feb. 10, 1925. Doctor Miller was for many years the Provincial Geologist of Ontario and the one who more than any other had contributed by his personal work and the reports of his subordinates to the recent extraordinary mineral development of the Province. Doctor Miller was fifty-eight at the time of his decease. A man of unusually stalwart physique, he seemed destined to many years of useful service. His friends in both the American and Canadian Mining Institutes can with difficulty reconcile themselves to his loss. Doctor Miller was born in 1867 in Port Rowan, Ont., on the shores of Lake Erie. After preparation in the high school of his native town, he entered the University of Toronto and took his bachelor&apos;s degree in 1890. He pursued graduate studies in geology at Chicago, Harvard, and Heidelberg Universities. In 1893, he was first appointed lecturer and soon thereafter Professor of Geology in Queens University, Kingston, Ont., a chair which he held until 1902. He was then appointed Provincial Geologist of Ontario and was placed at the head of the Survey which was attached to the Department of Mines. Within the next year, 1903, he performed the service that made him famous. In the summer of 1903, in connection with the building of the Ontario Government Railway toward an objective on James Bay, veins had been noticed by construction parties just north of what is Cobalt Lake today, and in the rocky pass that is now traversed by the main line of the Canadian National Railway en route to Vancouver. The pink stain of cobalt bloom on the vein, known later as La Rose, caught the eye of a workman; in November, Doctor Miller recognized the silver in it, and brought the possibilities of the district to general attention. In December, he published an article in the Engineering and Mining Journal, stating that the veins could be worked at a handsome profit. During the winter and spring, the mining interest awoke, which resulted in the astonishingly productive silver district of Cobalt; but in which, Doctor Miller, because a government official, scrupulously refrained from having any financial interest whatever. Seldom has so high a sense of honor been manifested; and as the result, Doctor Miller commanded confidence and respect to an extraordinary degree. Hard on the discoveries at Cobalt came, in the next few years, those at the other famous camps in Northern Ontario; and step by step with them, reports issued from

Jan 1, 1925

By R. H. Swallow, George Hess

C. G. BALL*—These maps are obvi-~,usly quite helpful in many types of mining engineering, but I want to find out if the prints which you obtain in the first step toward making any aerial contour map have already been corrected for tilt. Is that done afterwards only if you are going into the process of making a contour map ? GEORGE HESS (authors&apos; reply)— The tilt correction is the first step in either compiling the mosaic or compiling the total map. They must be corrected. C. G. BALL—But are the contact prints themselves corrected for tilt? GEORGE HESS—They are not corrected. E. R. KAISER†—I enjoyed this paper very much, and am glad to learn that the methods have a high degree of accuracy and are in use in the coal industry. Accuracy in dimensions is understandable from the paper. Would you tell us how accuracy can be obtained in the vertical dimensions by means of the photographs so as to permit drawing contour lines? GEORGE HESS—To explain our process, even in a limited way, is quite a large order. However, the basic principle involved is the measurement of parallax by viewing two overlapping photographs stereoscopically. It would almost be necessary to have the various instruments here on view to adequately explain their operation. E. R. KAISER—Are the elevations for reference obtained at more than four points ? GEORGE HESS—The pattern of control is four points obtained in the corners. Primarily. that is to restitute the picture and horizontalize it. The vertical control points are read ill on the stereometer and a direct comparison is made while draw- ing the contour lines. You do have to have those four points. But one stereoscopic pair of 5 ft contours has some 340 acres on it, consequently for every four points picked up 340 acres are contoured. E. R. KAISER—How does your method compare with that used by the military reconnaissance during World War II? GEORGE HESS—The Army did not get into this refined mapping. Most of their work has been reconnaissance mapping by taking one vertical and two oblique views. Basically, the same principle is used. Our maps are for engineering purposes. The Army was primarily interested in reconnaissance. E. R. KAISER—You could take more than 48 pictures in one flight? GEORGE HESS—Yes, the Brock camera accomodates 48 pictures per magazine. We are limited by the hours of greatest light, though, 2 hr before high noon, and 2 hr after high noon. Shadows do affect the picture. The shadows can-

Jan 1, 1950

(Members are urged to send in for this column any notes of interest concerning themselves or their fellow-members) The following is a partial list of members and guests who called at Institute headquarters during the period Mar. 10, 1917, to Apr. 10, 1917. George S. Blair, Pittsburgh, Pa. E. P. Mathewson, Toronto, Canada. H. M. Boylston, Cambridge, Mass. T. Poole Maynard, Atlanta, Ga. F. J. Brule, Toronto, Canada. . W. J. Mead, Madison, Wis. M. B. Cohen, Miami, Ariz.. D. G. Miller, Denver, Colo. W. M. Corse, Buffalo, N. Y. P. N. Moore, St. Louis, Mo. F. G. Cottrell, Washington, D. C. R. H. Morris, Ansted, W. Va. E. C. Cross, Cleveland, 0. W. J. Morrison, Toronto, Canada. Nelson Dickerman, San Francisco, Cal. M. F. Ortin, Petrograd, Russia. F. N. Flynn, Chuquicamata, Chile. G. W. Paymal, New York, N. Y. F. L. Garrison, Philadelphia, Pa. Edward H. Perry, Boston, Mass. J. S. Grasty, Charlottesville, Va. 0. G. Petersen, Somerset, Ky. H. D. Hibbard, Plainfield, N. J. H. C. Price, Bartlesville, Okla. H. L. Hollis, Chicago, 111. C. A. Richardson, Toronto, Canada. F. H. Jackson, Marysvale, Utah. Hallet R. Robbins, Vancouver, B. C., Can. W. Strickler Jones, Silver City, N. M. A. H. Rogers, Boston, Mass. E. B. Kirby, St. Louis, Mo. H. G. Smith, Princepulca, Nic. J. M. Lovejoy, Electra, Tex. Edwin G. Steele, Van Horn, Tex. A. F. Lucas, Washington, D. C. &apos;S. A. Taylor, Pittsburgh, Pa. Edwin Ludlow, Lansford, Pa. A. P. Thompson, Salt Lake City, Utah, E. Francis McCrossin, Birmingham, Ala. Milton A. Allen is now engaged in the New York office of Messrs. Arthur L. Pearse & Co. Percy E. Barbour, managing editor of the Engineering & Mining Journal, has been appointed, by Governor Whitman, Deputy Superintendent of Police of the State of New York.

Jan 6, 1917

By J. J. Forbes

&apos;"THE Federal Coal Mine Safety Act (public Law T. 552. 82nd Congress) was approved oil July 16, 1952. It incorporates, as Title I, the Coal Mine Inspectio1.1 and Investigation Act of May 7. 1941 (Public Law 49, 77th Congress), which gave Federal inspectors only the right to enter. coal mines for inspection and investigation purposes but no power to require compliance with their recommendations. Title 11 contains the enforcement provisions of the act; its purpose is to prevent major disasters in coal mines from explosions, fires. inundations. and man-trip 01. man-hoist accidents. At this point a brief account of events that preceded the enactment of the Federal Coal Mine Safety Act seems appropriate. The hazardous nature of coal mining was recognized by the Federal Govermment as long ago as 1865, when a bill to create a Federal Mining Bureau was introduced in Congress. Little was done, however, until a series of appalling coalmine disasters during the first decade of this century provoked a demand for Federal action. As a result an act of Congress established a Bureau of Mines in the Department of the Interior on July 1, 1910. The act made it clear that one of the foremost activities of the Bureau should be to improve health and safety in the mineral industries. One of the first projects selected by the small folce of engineers and technicians then employed was to determine the causes of coal-mine explosions and the means to prevent them. By investigations aftel mine disasters the fundamental causes and means of prevention were soon discovered, and the coal mining industry was informed accordingly. However, despite this knowledge and the enactment of State laws and the Federal Coal Mine Inspection and Investigation Act of 1941, mine disasters continued to occur with disheartening frequency and staggering loss of life. The devastating explosion at the Orient No. 2 mine on December 21, 1951, resulted in the death of 119 men. The Orient disaster rekindled the memory of the Centralia. Ill., disaster of March 25. 1947, which caused the death of 111 coal miners. These two tragedies ultimately brought about enactment of the Federal Coal Mine Safety Act. The act is a compromise measure. Senator Matthew M. Neely of West Virginia and Congressman Melvin Priec of Illinois introduced almost identical versions in the 82nd Congress, but they were considered too drastic. The final version was introduced by Congressman Samuel K. McConnel, Jr., of Pennsylvania, after considerable discussion and amendment in committee hearings. It was passed by the Congress and became effective when signed by the President on July 16, 1952. The act is somewhat limited in scope because it applies only to approximately 2000 coal mines in the United States and Alaska that employ regularly 15 or more individuals underground. It exempts approximately 5300 mines employing regularly fewer than 15 individuals underground and all strip mines, of which there are about 800. Moreover, it covers only conditions and practices that may lead to major disasters from explosion, fire, inundation, or man-trip or man-hoist accidents. According to Bureau records, such accidents have resulted in less than 10 pct of all the fatalities in coal mines. It is important to mention that the law is not designed to prevent the day-to-day type of accidents that have caused the remaining 90 pct or more of the fatalities, because it was the specific intention of the Congress to reserve the hazards which caused them to the jurisdiction of the coal-producing states. Many who opposed any Federal legislation that would give the Federal inspectors authority to require compliance with mine safety regulations claimed that such legislation would usurp or infringe upon States&apos; rights. To assure that the principle of States&apos; rights would be preserved, the act provides for joint Federal-State inspections when a state desires to cooperate in such activities. The Director of the Bureau of Mines is required by the act to cooperate with the official mine-inspection or safety agencies of the coal-producing states. The act provides further that any state desiring to cooperate in making joint inspections may submit a State plan for carrying out the purposes of this part of the act. Certain requirements are listed: these must be met by a state before the plan can be accepted. The Director of the Bureau of Mines, however, is required to approve any State plan which complies with the specified provisions. The Director may withdraw his approval and declare such a plan inoperative if he finds that the State agency is not complying with the spirit and intent of any provision of the State plan. When this paper was prepared, agreements for joint Federal-State inspections had been entered into with Wyoming and Washington. A few other states have indicated their desire to submit a State plan and negotiations toward that end are now under way. Reluctance to enter into such agreements may be due to the mine operators&apos; knowledge that in the states that adopt a cooperative plan they are prohibited from applying to the Director of the Bureau of Mines for annulment or revision of an order issued by a Federal inspector and must appeal directly to the Federal Coal Mine Safety Board of Review for such action. Experience has proved that review by the Director as provided in the act is a less expensive and time-consuming procedure to all concerned than applying to the Board. Reluctance also may stem from the fact that joint Federal-State inspections somewhat restrict the movements of the State mine inspectors and tend to reduce the number of inspections of mines. Where a State plan is not adopted, the Federal coal mine inspector is responsible under the law to take one of two courses of action if he finds certain hazardous conditions during his inspections. The first action involves imminent danger. If a Federal inspector finds danger that a mine explosion, mine fire, mine inundation, or man-trip or man-hoist accident will occur in a mine immediately or before the imminence of such danger can be elim-

Jan 1, 1955

THE book covers principally the assaying of silver and gold and the determination of these values in ores, sweepings, and base metal. It seems to have been written more for the goldsmith and jeweler than for the primary producer of metals. There were approximately sixty different substances needed in the operations described and not over a dozen different types of raw material (ore, matte, crude or alloyed metal) are mentioned. The methods of separation used were essentially simple and reasonably reliable, though the processes were not sufficiently understood to permit the selection of the simplest effective ingredients, and there was a great tendency to employ complicated fluxes, with unnecessary repetition of long-continued heatings indicative of a leisurely pace of life. Practically all the processes described are based on a few chemical facts: the inability of gold to combine with sulphur, while silver and the base metals form easily fusible sulphides; the ready oxidation of base metals; and the ii- solubility of gold in nitric acid. Fluxes serve to make earthy impurities fusible, and to carry oxidizing or sulphurizing ingredients. Many of the processes of assaying had changed little up to the beginning of the present century. Even as late as 1924, when the writer took a University course in fire assaying, the crucibles, cupels, scorifiers, molds, and tongs were identical with those of the sixteenth century, though the wind furnace had a stack on it and the muffle for cupelling was gas-fired.* The fluxes were purer, but of the same essential composition. That this branch- or twig-of metallurgy had not advanced in any funda-

Jan 1, 1949

1938 ABERNATHY, G E Feb 6, 1948 Min & Met Apr 1948 1937 ADAMS, ARMY Aug 20, 1949 Min Eng Dec 1949 1946 ADDY, GEORGE E Sept 24, 1950 Min Eng July 1951 1920 ALDERSON, WILTON P Feb 1951 Min Eng Sept 1952 1896 ALDRICH, T H , JR May 24, 1950 Min Eng Aug 1950 1942 ALDRIDGE, LEONARD June 8, 1952Jrn Met Sept 1952 1919 ALLEN, ROLLAND C July 18, 1948 Min &Met Sept 1948 1950 ANDERSON, C P Unknown Min Eng Feb 1951 1937 ANDERSON, JOHN H May 10, 1950 Min Eng Aug 1950 1914 ANDERSON, L DOUGLASS Unknown Min Eng Nov 1951 1948 ANDRAU, E W K Oct 20, 1951 1936 ANDREWS, CHARLES B Apr 19, 1950 Min Eng June 1950 1918 ARMITAGE, PAUL June 28, 1949 Min Eng Oct 1949 1924 ARMSTRONG, PERCY A E Jan 23, 1949 Min Eng May 1949 1906 ARNOLD, CHARLES LE NEVE Aug 7, 1949 Min Eng Oct 1949 1945 ARNOLD, HAROLD S Aug 7, 1950 Min Eng Oct 1950 1936 ASH, JAMES E Dec 17. 1949 Min Eng Apr 1950

Jan 1, 1952