Search Documents

Part 1. Coal Part 2. Industrial Minerals

Jan 3, 1977

By Edward F. Winter, C. E. Ruoff

A silicon solid-state array image scanner is described. This paper deals with structural and performance properties of the array which basically consists of PIN photo and gating diodes, and low capacitance isolation diodes. Each chip of the array is composed of an 8 by 9 matrix of photo detector cells; each cell contains one each of the three diode types mentioned. This x-y matrix is read a column at a time with an access delay of approximately 100 nsec per column. It is designed to detect the presence or absence of illumination within 10-mil diam image spots located on a 15- by 15-mil grid. Radiant power level of an illuminated spot is low; of interest is the range around I uw with a of 8400g Structural improvements to the original array which will result THE purpose of this paper is to describe the results of a solid state scanner exploratory development activity. The scanner is intended to sense the presence or absence of low-level illumination falling upon a matrix of 10-mil wide squares arranged on a 15- by 15-mil x-y grid pattern. The light of interest has a wavelength of 8400, characteristic of radiation emitted from a GaAs lasing diode. This wavelength matches well the spectral absorption of silicon,' thus the well-developed silicon processing technology can be applied to fabricating large integrated arrays of PIN photocells to sense the radiation. The illumination state of the cells of the array is read, one column at a time, by addressing a drive line of the particular column in question and examining the state of those sense lines which are orthogonal to the drive Lines of in greater sensitivity at various wavelengths, both above and below 8400Å, and in greater speed are presented. These include variations in diffusion depth, resistivity of N and P regions, isolation techniques, and packaging. Trade-offs between access speed, cycle frequency, and sensitivity are discussed. A packaging approach to achieving an array composed of several chips is described. Requirements on this package are: 1) maintenance of 15- by 15-mil pitch of the light sensitive cell position, therefore positional accuracy of mounted 8 by 9 cell photo detector chips; 2) maintenance of inherent high array speed even though signal levels are low through high density close proximity mounting of monolithic sense amplifier circuitry. the array. One bank of N sense amplifiers is required, where N is the number of photodiode cells in each column of the array. CELL AND CHI" STRUCTURE A photograph of a single monolithic cell is shown in Fig. 1. Each cell is composed of three junctions, an isolation junction, a logic or blocking diode junction, and a photodiode junction; all of these junctions are connected electrically by a common N region. An electrical schematic of four cells of the array is shown in Fig. 2 with the associated driver and sense amplifier circuits in block diagram form. Note the common cathode configuration of the three diodes of each cell. Fig. 3, a diagram of the cell vertical struc ture, illustrates how the electrical configuration of

Jan 1, 1970

By Herbert R. Hanley

THE One Hundred and Twenty-sixth meeting-of the Institute, held in San Francisco, Sept. 25 to 29, 1922, was a success in every way. Character-istically, San Francisco presented climate suited, to the occasion, while the Committees on Arrangements left nothing undone that would contribute to the interest and entertainment of the members and their wives. There was a registration of over 230, and all sections, save three, were represented. In the technical meetings, under the leadership of Albert Burch in the mining session and C. W. Merrill in the milling session, the greatest interest was manifested in ore-hunting geology and modern ore-dressing methods. The general geologic phase developed numerous discussions and had for its aim the study and correlation of known data and the application-of these to the finding of commercial orebodies. The geologic features of the Comstock and their significance to the development of the present orebodies were discussed. This brought out matters of much technical interest as well as those of romantic nature in the history of the early life of that camp. The profitable application of modern milling methods to ores, non-commercial a short time ago, was discussed with much interest. The recent work on the Comstock ores occupied a conspicuous part in these discussions. Basic principles delineated by mathematical study of mechanical devices for the milling of ore came in for a prominent part in the program as well as the physical-chemical side of the processes devised for the winning of precious metals as a profit.

Jan 11, 1922

By Paul D. Merica, O. B. J. Fraser

PROBABLY the first metallic objects used by man were nickel alloys. In search for flints suitable for the fashioning of their rude tools, our paleolithic ancestors, some 25,000 years ago, quite likely may have come upon some of those heavy, metallic fragments that we now know as meteorites, which consist of an alloy of nickel and iron containing usually from 5 to 15 pct of nickel. Whether paleolithic man ever did discover and use meteoritic fragments, his sketchy records do not actually disclose. We do know, however, that such fragments have been found and used by peoples, particularly the North American Eskimos, for weapons and implements in just the same manner as stones, and prior to any knowledge by those peoples of the reduction of metals from ores. Meteoritic showers were recorded frequently in earliest times and the meteorites often were found and fashioned into useful objects. The ancient Arabic and other myths of "invincible swords fallen from heaven" seem thus to have had a very definite basis in fact, and such weapons, of meteoritic material, have actually been re- covered from archeological excavations. It thus seems probable that meteoric nickel-iron was found and used long before iron was recovered by smelting iron ores (perhaps about 1200 B.C.) and probably even before there was knowledge and use of bronze and gold. Although many centuries were to pass before nickel was first isolated, in 1751, from Swedish ores and recognized as an elemental

Jan 1, 1953

By FRANK R. VAN

I. INTRODUCTION. IN the summer of 1908, R. B. Cochran, Superintendent of the Compania Metalurgica Mexicana at Sierra Mojada, Mexico, presented to the Department of Geology and Mineralogy at Case School of Applied Science an interesting series of silver-, copper-, and lead-ores from the Veta Rica mine. These ores contained several interesting minerals which were associated in a somewhat peculiar manner, so that I was impelled to make a closer study of their occurrence. The investigation has brought out several new facts concerning the geology of the district and the geological occurrence of the ores, and therefore has seemed worthy of record. Two papers have been published previously about the region, one by Chism1 in 1887, and the other by Malcolmson2 in 1902. These articles, however, treat of the district more from the stand-point of the metallurgist and mining engineer, and not much attention is devoted to its mineralogy and economic geology. II. GEOGRAPHICAL LOCATION OF THE DISTRICT. The Sierra Mojada is situated in the extreme western part of the State of Coahuila, near the Chihuahua boundary. It is reached best via the Mexican Central railroad from El Paso, Tex., to Escalon, Chihuahua, a distance of 494 miles. From this point, a branch line, the Mexican Northern railroad, runs 78 miles in a NE. direction to the mines, which are its northern terminus. The railroad was built about 1890, practically on account of the Sierra Mojada mining-district. 1 Sierra Mojada, Mexico, by Richard E. Chism, Trans., xv., 542 (1886-87). 2 The Sierra Mojada, Coahuila, Mexico, and Its Ore-Deposits, by James W. Malcomson, Tram., xxxii., 100 (1901).

Aug 1, 1912

COUNCIL OF SECTION DELEGATES E H Stevens, Chairman James W Halley, Vice-Chairman George J Donaldson, Secretary The Peoples Natural Gas Co 140 Stanwix St Pittsburgh 22, Pa EXECUTIVE COMMITTEE H R Wardwell, J G Evans, H R Bianco, Harry Campbell

Jan 1, 1955

By E. G. Schempp, W. A. Morgan

The influence of modifications in the molybdenum, vanadium and, to a limited degree, carbon and boron content to a basic composition of 5 pct Cr, 0.75 pct Mo, 1 pct V hot-work tool steel composition, was studied in respect to hardenability, grpain- coarsening temperature, and tempering charactevistics. Tensile, impact, and fatigue pvoperties were studied for the most promising compositions. An alloy with a typical composition of 0.43 pct C, 4.97 pct CI-, 0.33 pct Si, 2.25 pct Mo, and 1.00 pct V uas found to offer the most favorable combination of properties in respect to high-strength applicntions when tempered at 1100°F. MANY 5 pct Cr high-strength steels are at present being manufactured in North America which fit well into the classification of the AISI-SAE system. Much interest has been shown in these materials as ultra-high-strength steels for use at elevated temperatures. The limiting temperature of use lies at the point where the steels begin to soften rapidly. Although a great deal of information has been made available in the past two years on the properties of selected alloys in this series, little information exists on the effect of systematically varying the ccntent of one or more elements in the 5 pct Cr-base alloy. This paper presents the results of an investigation of the effect of variations of the carbon, molybdenum, vanadium, and, to a limited extent, the silicon, manganese, boron, and niobium content of a 5 pct Cr steel to the AISI H-13 base analysis. EXPERIMENTAL PROCEDURE All experimental heats were melted in a 50-lb. induction furnace. The melting stock consisted of

Jan 1, 1962

SEC. 1. The membership of the Institute shall comprise seven classes, namely: 1. Members; 2. Honorary Members; 3. Senior Members; 4. Associates; 5. Junior Members; 6. Rocky Mountain Members; 7. Junior Foreign Affiliates. All shall be equally entitled to the privileges of membership, excepting that no member of any class whose residence shall be outside of the United States of America, except those residing in Mexico and Canada, shall be entitled to vote. SEC. 2. Members: A person to be eligible for election or transfer into the class of Member must be at least 27 years of age and must have had at least six years' employ¬ment in the practice of engineering, mining, geology, metallurgy, or chemistry, during at least three years of which he must have held positions of responsibility in one or more of these fields. This shall not apply to Rocky Mountain members. SEC. 3. Honorary Members: Each candidate for Honorary Membership must be recommended by at least ten Members and must be elected by ballot at a meeting of the Board of Directors by the unanimous vote of the Directors present; provided, how¬ever, that the number of Honorary Members shall at no time exceed twenty. Such election shall automatically act as a transfer of such member from any other class of membership to which he may belong. SEC. 4. -Senior Members: The Directors may in their discretion place on the Honor Roll of Senior Members and transfer from any other class of membership other than Honorary Membership the name of any Member or Associate who has reached the age of seventy years and who has paid dues for thirty years, and for good reasons in special cases may vary the age or number of years. SEC. 5. Junior Members: A person to be eligible for election to the class of Junior Member must be qualified through education or experience to hold a subordinate position in engineering, mining, metallurgical, geological or chemical work. He shall be not more than 33 years of age at the time of election. SEC. 6. Associates: A person eligible for election or transfer into the class of Associate shall be one, who, in the opinion of the Committee on Admissions and the Board of Directors, is suitable for such election or transfer by reason of his interest in or connection with mining, geology, metallurgy, or chemistry. SEC. 7. Rocky Mountain Members: Membership in a special class of life member¬ships without annual or other dues and without right to receive the printed literature distributed to other members or the right and privilege of wearing the official badge of technical members, is given to all members of the Rocky Mountain Club at the time of consolidation. These special Rocky Mountain memberships shall be claimable by any member of the Rocky Mountain Club, not already a member of the Institute, availing himself of the privilege within ninety days after mailing of notice to him, by the Secretary of the Institute. SEC. 8. Junior Foreign Afliate: Upon appropriate action by the Board of Direc¬tors and with its approval, members in good standing of any technical society having its headquarters outside of the United States of America, Canada, or Mexico,

Jan 1, 1937

ALABAMA Anniston.-Carrington, F. G. Auburn.-Brown, R. L. Bessemer.-Abbott, C. E. Dobbs, G. G. Ferguson, V. Salmon, H. S. Schaber, C. F. Birmingham.-Aldrich, T. H. Aldrich, T. H., Jr. Allen, A. W, Ball, E. M. Bonnyman, J. Bowron, J. Bush, M. W. Crawford G. G. Crockard, F. H. Ellis, E. E. Fairbairn, C. T. Gallacher, J. Geisiner, H. S.

Jan 1, 1917

By Carl Scholz

Discussion of the paper of Carl Scholz, published in Bi-monthly Bulletin, No. 22, July, 1908, pp. 551 to 559. HOWARD N. EAVENSON, Gary, W. Va. (communication to the Secretary*) :-For some time before the publication of Mr. Scholz's paper, I had been collecting data bearing upon its subject, and I now take pleasure in presenting my results to the Institute in the form of a discussion. It has long been a matter of common opinion among mining-men that mice-explosions are, more frequent during the colder, or winter months, than during the warmer ones, and it is a matter of common knowledge among them that the air-ways and road-ways in most mines are much drier and are more in¬clined to be dusty during the winter than during the summer. In many mines, places which are wet and sloppy in the summer are dry and sometimes dusty during the winter. These changes, of course, can only be due to atmospheric conditions, and are caused by differences in temperature and humidity. Until recently, however, very little attention has been paid to the part that atmospheric conditions may play in mine-explosions, or, rather, to the effect they may have in rendering mine-conditions peculiarly dangerous, and in spreading and rendering more disastrous the effects of what would otherwise probably have been .small explosions. To show the difference in mine-conditions during sunnier .and winter months, I have tabulated in Table I. the results of 24 observations of hygrometric conditions in several different mines at different times of the year. Mines Nos. 1, 2, and 6 are located in the Pocahontas.coal -region, in McDowell couuty, W.Va., the first one being a shaft-mine shaft mine and the others drift. Mines 1A and 2A are drift-mines located in Logan county, W. Va. All of these are mines of fair size, but none of them has been in operation more than six years,

Jun 1, 1909

By W. J. Taylor

IN making heating gas with anthracite coal for roasting ore during the past few years, I hare tried many forms of gas generators. So far, the most successful and satisfactory one has been what we call a fluxing producer, which is simply a small cupola or blast furnace, in which we charge with the coal, say, 30 or 40 per cent. of basic blast-furnace cinder, to unite, when melted, with the ash or earthy matter in the coal, and carry it off as cinder. The producer we have in use at Chester, N. J., has pore of the lines of a blast furnace than a cupola, the hearth being 24 inches diameter and 24 inches high. It then enlarges on an angle of about 25 degrees from a perpendicular to 4 feet, and then is drawn into 3 feet on top ; total height, 12 feet. We use one water coil-tuyere 12 inches above the bottom, and blow through a 11/2-inch nozzle. The depth of coal above the tuyere averages about 6 feet. The producer. is blown with

Jan 1, 1881

By R. C. Dalzell, A. E. Wells

In 1866, Thomas Graham1 called attention to the volume of gases, three times the volume of the sample, evolved from a meteoric iron heated in an evacuated porcelain tube. From that time to this the occurrence and significance of gases in metals have been the subject of investigation by many workers, among whom Sieverts,2 Iwasé3 and 0. W. Ellis4 stand preeminent. Sieverts and Iwasé concerned themselves with the solubility of a number of gases in metals in the liquid and solid states. They determined the absorption coefficients of these gases, and in all cases found a sharp change in solubility at the melting point of the metals. Ellis analyzed the gases evolved by solidifying copper and those occluded by the solidified metal. Lobley and Jepson5 endeavored to determine the effects of hydrogen, carbon monoxide and nitrogen on the porosity of copper that was allowed to solidify in the presence of each gas after 30 min. exposure to it in the

Jan 1, 1930

By R. W. Culbertson, S. Kasper

During the 1920's, approximately 11,000 small gasifiers were in operation in the United States. They converted about 15 million tons (13.6 Mt) of coal per year into low Btu gas. In some cases, hot raw gas was used for applications such as firing open hearth furnaces or brick kilns. In other cases the gases produced in the gasifiers were cooled, cleaned and desulfurized for various utility and industrial purposes. The steel industry was by far the largest user. The most important fact was that the conversion of coal to a usable fuel gas was demonstrated to be commercial. During the late 1940's and early 1950's, this form of energy was largely replaced by natural gas as the pipeline net work was expanded. Producer gas was no longer economically competitive. Over the past 25 years, government controls on the interstate price of natural gas have maintained this situation. At present only three commercial small coal gasifier plants are still in operation in the United States. These facilities are operated

Jan 1, 1980

By W. J. Taylor

In making heating gas with anthracite coal for roasting ore during the past few years, I have tried many forms of gas generators. So far, the most successful and satisfactory one has been what we call a fluxing producer, which is simply a small cupola or blast furnace, in which we charge with the coal, say, 30 or 40 per cent. of basic blast-furnace cinder, to unite, when melted, with the ash or earthy matter in the coal, and carry it off as cinder. The producer we have in use at Chester, N. J., has more of the lines of a blast furnace than a cupola, the hearth being 24 inches diameter and 24 inches high. It then enlarges on an angle of about 25 degrees from a perpendicular to 4 feet, and then is drawn into 3 feet on top ; total height, 12 feet. We use one water coil-tuyere 12 inches above the bottom, and blow through a 1 1/2 - inch nozzle. The depth of coal above the tuyere averages about 6 feet. The producer-is blown with

Jan 1, 1881

By G. L. F. Powell, L. M. Hogan

Samples of silver and Ag-O alloy, 0.12 wl pet, have been undercooled to a maximum of 250°C by melting in a slag of commercial soda-lime glass. Grain refinement occurred in undercooled silver samples whet the degree of undercooling exceeded a critical value which varied from 153° to 175°C, depending on the melting conditions. In under cooled Ag-0 samples, the grain structure was fine and equiaxed at degrees of undercooling larger than 50oC. The grain refinement in both silver and Ag-0 alloy samples was the result of recrystallization during or immediately following freezing. When the oxygen content was increased, the degree of undercooling at which recrys-tallization occurred decreased. INVESTIGATIONS of the grain structure of strongly undercooled melts of nickel and cobalt1-4 have revealed a change in room-temperature grain size as a function of undercooling. At large degrees of undercooling the grain size was fine, but samples undercooled by smaller amounts exhibited a much coarser grain structure. The reported undercooling at which this grain size transition occurred in nickel varied between 140° and 175'C undercooling. Walker1 attributed this grain size change to an enhanced nuclea-tion rate. Cavitation at a melt-solid interface was con sidered to generate a high-pressure wave. This, in turn, produced nucleation in the liquid as a result of an elevated freezing point increasing the undercooling in the melt. A similar grain size transition was observed in undercooled silver between 133° and 153°C undercooling.5 The grain size transition in undercooled silver was found to be dependent on oxygen con tent. More recently, the authors5 showed that a simila transition occurred in an undercooled Cu-O alloy, =0.08 pet, but not in oxygen-free copper undercooled more than 200°C. The transition was attributed to recrystallization of the solidified grains after freezing; the greater the degree of undercooling, the more complete the recrystallization. In view of this effect of oxygen content on grain size transition, additional undercooling experiments were carried out with silver. This paper reports the results of these studies on silver and Ag-O alloys undercooled more than 50°C EXPERIMENTAL 1) Materials. The silver was supplied by Matthey Garrett Pty., Ltd., as fine granulate, silver mini' mum 99.9 pet, and contained the trace impurities shown in Table I. The silver originated from two different refineries resulting in the difference in impurity content shown in Table I. However, the variation in composition had no discernible effect on the undercooling behavior. Samples of the silver were melted in an open-ended, vertical, cylindrical resistance furnace, wound with Kantha] wire, the temperature of which was adjusted by means of a variable transformer, 2) Melting and Undercooling. Bulk samples of silver were undercooled by preoxidation and removal of oxidized impurities in a glass slag, as previously described,5 but special precautions were necessary to allow comparison between oxygen-free silver and a Ag-O alloy. Samples free of oxygen were prepared by first melting weights of granulate varying from 200 to 400 g in clean vitreous silica crucibles in air for approximately 15 min. A sample was frozen and a complete glass cover formed over the top surface by adding granulated glass rod. The sample was then melted and frozen several times until no oxygen bubbles appeared in the glass slag. Subsequent thermal analysis indicated that the oxygen content was negligible. The glass acted as an efficient barrier to absorption of oxygen from the air. Ag-O alloys were prepared by melting silver in silica crucibles with only a partial cover of glass, so that the top surface of the melt was in contact with air. The silver was held molten in air for several hours at 1000° to 1050°C, in the expectation that the oxygen in solution would reach equilibrium with atmospheric oxygen. At T - 1000°C the equilibrium oxygen content was calculated as 0.12 wt pet O, using Sieverts law and Eq, [l], derived by Mizikar et a!.7 from the data of Sieverts and Hagenacker8 for 1 atm of oxygen:

Jan 1, 1970

By E. F. La Vigne

On Aug. 10, 1884, the Retsof Mining Co. began the sinking of an 18 by 12-ft. shaft at Retsof, N. Y. Rock salt was reached in 1885, in September, at 1008 ft. below the surface. The first salt was shipped in the fall of 1885. A timber breaker was built in 1886. In July, 1895, there was a consolidation of the Retsof Mining Co., the Greigsville Salt & Mining Co., the Livonia Salt Co., and the Lehigh Salt & Mining Co. These consolidated salt companies are now known as the Retsof Mining Co., a subsidiary of the International Salt Go. Eventually all of the mines were closed except the mine of the Retsof Mining Co., at Retsof, Livingston County, New York. On July 6, 1921, about 1/2 mile south of the original shaft arid plant of the Retsof Mining Co., a new 9 by 28-ft. concrete-liried shaft was started. The shaft is 1063 ft. deep from the top of the shaft collar to the bottom of the salt bed. At the same time a reinforced-concrete breaker and other buildings were erccted. This new plant began operations on Dee. 15, 1923. It was designed for a capacity of 3000 tons in 8 hours. Geology The workable rock-salt bed is 1063 ft. below the surface and 326 ft. below sea level, and varies in thickness from 9 to 10 ft. The total thickness is greater than that but is contaminated with shale above and below the pure mineral. The characteristics of the formation are shown in Tables 1 and 2. The bed dips uniformly 0.87 per cent to the south. Prospecting As the salt deposil in New York State is known, very little prospecting has been necessary. Before the sinking of the Retsof No. 1 shaft, a well was drilled to prove the existence of salt. No. 1 shaft was sunk where the well was located. The several salt wells drilled in Livingston Courlty proved generally the existence of salt throughout the county. (See U. S. Geol. Survey Bull. 669: Salt Resources of the U. S.)

Jan 1, 1938

By E. F. La Vigne

On Aug. 10, 1884, the Retsof Mining Co. began the sinking of an 18 by 12-ft. shaft at Retsof, N. Y. Rock salt was reached in 1885, in September, at 1008 ft. below the surface. The first salt was shipped in the fall of 1885. A timber breaker was built in 1886. In July, 1895, there was a consolidation of the Retsof Mining Co., the Greigsville Salt & Mining Co., the Livonia Salt Co., and the Lehigh Salt & Mining Co. These consolidated salt companies are now known as the Retsof Mining Co., a subsidiary of the International Salt Go. Eventually all of the mines were closed except the mine of the Retsof Mining Co., at Retsof, Livingston County, New York. On July 6, 1921, about 1/2 mile south of the original shaft arid plant of the Retsof Mining Co., a new 9 by 28-ft. concrete-liried shaft was started. The shaft is 1063 ft. deep from the top of the shaft collar to the bottom of the salt bed. At the same time a reinforced-concrete breaker and other buildings were erccted. This new plant began operations on Dee. 15, 1923. It was designed for a capacity of 3000 tons in 8 hours. Geology The workable rock-salt bed is 1063 ft. below the surface and 326 ft. below sea level, and varies in thickness from 9 to 10 ft. The total thickness is greater than that but is contaminated with shale above and below the pure mineral. The characteristics of the formation are shown in Tables 1 and 2. The bed dips uniformly 0.87 per cent to the south. Prospecting As the salt deposil in New York State is known, very little prospecting has been necessary. Before the sinking of the Retsof No. 1 shaft, a well was drilled to prove the existence of salt. No. 1 shaft was sunk where the well was located. The several salt wells drilled in Livingston Courlty proved generally the existence of salt throughout the county. (See U. S. Geol. Survey Bull. 669: Salt Resources of the U. S.)

Jan 1, 1938

By C. Stansfield Hitchen

THE introduction of the logarithmic sector method of quantitative spectrography by Scheibe and Neuhäusser in 1928, and the subsequent .modification and improvement of the method by Twyman and Simeon, would seem to have marked yet a further advance in quantitative spec-trum analysis and its industrial application, inasmuch as it offers a simple means of eliminating some of the uncertainties inherent in the older methods based upon mere visual comparison of line intensities. In their recent admirable review of the position and capabilities of industrial spectroscopy, Brownsdon and van Someren1 say: Ways and means of facilitating the comparison of line-intensities so as to give them numerical values are helpful, and of these a logarithmic sector rotating in front of the slit appears to he one of the most promising; . . . the success recently experienced by the author in using this method for the examination of steels and solutions of metallic salts prompted him ,to investigate its possible use in estimating the impurities commonly present in crude and refined tin. The results of this investigation are submitted in the present paper. Details of a number of spectrographic analyses of tin for various impurities have already been published. Thus, Schweitzer2 describes the spectrographic examination of tin for lead, bismuth and cadmium, and was able to distinguish between such atomic percentages as 0.01, 0.05, 0.10, 0.30, 0.60, 1.20, 3.00 and 10.00. Negresco3 investigated the bismuth content of tin over a range of from 0.0005 to 35 per cent. Meggers, Kiess and Stimson4 compare spectrographic and chemical analyses of tin metal for copper, lead, iron, zinc, silver, nickel and bismuth. They stress also the value of spectrum analysis in the examination of tin used for boiler plugs, where the requirements that only minute quantities of impurities shall be present render the chemical analysis both tedious and difficult.

Jan 1, 1933

By G. S. Rice, J. A. Davis

The Péchelbronn oil field is located in the province of Alsace, in the Rhine Valley, about 30 miles north of Strasbourg. It is approximately 4 miles wide and 12 miles long, extending from the villages of Lobsann on the north to Wintershausen and Ohlungen near Haguenau on the south. (See Fig. 1.) The productive area includes about 44,000 hectares (107,680 acres). The name Péchelbronn signifies "pitch-spring" or "pitch-fountain." The first exploratory galleries were driven in from the hillside in 1735; and in 1745 the first official concession was granted by the French government and the first pit sunk to a depth of about 30 ft. Extraction by drilled wells was begun in 1879, supplementing the mining operations, and during the next 10 years 200 wells were drilled to an average depth of 172 m. (568 ft.). The bringing in of two "gusher" wells, in 1882 and 1888, respectively, was followed by the abandonment of all underground work. Underground mining, with a view to increasing the production of petroleum by recovering the oil left in the sands after drilling wells, was resumed in 1916. This mining operation started by sinking shaft No. 1 to a depth of 150 m. (495 ft.). The underground developments were pushed during 1917 and 1918 and the annual production of the Péchel-bronn field was increased to about 50,000 metric tons or 350,000 bbl. On the signing of the Versailles Treaty the province of Alsace, which had been taken by Germany as the result of the war of 1870, was returned to France, and the proprietary rights were taken over by the French Government. Concessions or leases, which embraced all the known oil-bearing territory of the field, were granted to the present operating company, Mines de Péchelbronn. This company followed both the drilling and the mining methods of the previous company.

Jan 1, 1927

NEW MEMBERS The following list comprises the names of those persons who became members during the period May 10 to June 10, 1915: Members ANDREEN, HARRY MAYO, Millman: and Assayer Thane, Alaska. BANKS, HUBERT RAYMOND, Min. Engr., Mill Staff, Consolidated Arizona Smelting Co., Humboldt, Ariz. BASSETT, ARTHUR F., Min. Engr., Care Consolidated Arizona Smelting Co., Humboldt, Ariz. BLACKNER, LESTER A., Slope Engr.... Care Ray Consolidated Copper Co., Ray, Ariz. BUSHNELL, C. E., Draftsman Butte & Superior Copper Co., Butte, Mont. CAVAGNARO, DAVID AMILE, Min. Engr., Genl. Supt., Wisconsin North Fork GravelMines, Forest, Sierra Co.; Cal. COGHILL, WILLIAM HAKES, Met., Ore Testing Laboratory, 3705 Hueco St., - - El Paso, Tex.

Jan 7, 1915