Search Documents

By Thomas N. Walthier

Throughout the world, governments are placing increasingly severe restrictions on mineral exploration and mining activities. One result is that there are fewer places left where mining companies are wanted or investors are willing to go.

Jan 4, 1976

Schedule of Events

Jan 1, 1977

By A. A. Dor

Out of nine new major iron ore concentrators put in operation during the last three years, or expected to be commissioned in 1968, seven incorporate primary grinding mills and have a total design capacity of 13,150,000 ltpy of pellets, while only two include conventional rod and ball mill grinding circuits for a total design capacity of about 6,100,000 ltpy (Table I). This evolution in the application of primary grinding to hard, fine grained magnetite ores represents an important development in the technology of mineral processing. It has been the outcome of comprehensive testwork in the laboratory and in pilot plants.

Jan 11, 1968

Jan 1, 1923

By R. H. Hawkins

AN investigation of the applicability of geophysical methods to north-ern Ontario lignite deposits was undertaken early in 1930 by the Ontario Research Foundation at the request of the Ontario Department of Mines TABLE 1.-Formations Associated with Moose River Basin Maximum System Formation Lithology Observed Correlation Thickness, Ft. Pleistocene Marine clays 150 Glacial till (Minimum Interglacial 30) clay and peat Glacial till Lower Cretaceous or Mattagami Fireclay, sand 138 Kootenay (?) Upper Jurassic. and lignite Devonian (Upper) Long Rapids Petroliferous, 50 Portage and black and gray Genesee shale Williams Limestone and 87 Tully (?) Island calcareous shale Devonian (Middle).... Abitibi River Gray fossiliferous 65 Onondaga limestone Devonian (Lower) ?... Moose Rive- Limestone and 50 gypsum Devonian (Loner) Sextant Arkose, clay, etc. 50 Pre-Cambrian Syenite, granite gneiss, etc. Igneous intrusives. . Lamprophyre dikes cut the Abitibi River and lower formations. (Permission of Ontario Dept. of Mines) and was financed in part from a research grant made by the latter organ-ization. The work to date has included gravitational, magnetic and electrical resistivity studies. The gravitational and magnetic measure-

Jan 1, 1933

By J. A. Church

I. Early Furnaces,......423 11. Experiments with the HIgh-Shaft FURnace,..... 426 III. ExperMents wIth the Wide FURnace,..429 IV. ExperEentS with Extreme BOSH,... 43.2 V. Survival of the 56 by 180 IN. Furnace,.434 VI. Recent ExpeEiments,.....436 VII. SUMMary,........438 I. Early Furnaces. Copper blast-furnace construction in America has long recognized a general standard in the rectangular water-jacketed shaft with separate forehearth. The details, however, and especially those relating to shaft dimensions, have had to meet a great variety of conditions, and show no uniformity whatever. Selecting a few of the present day Western plants, we find furnace lengths varying from 12.5 to 87 ft., widths at tuyere level from 42 to 84 in., and heights above tuyeres from 5 ft. 4 in. to 22 ft. 4 in.; and comparing present designs with those of the past, we meet contrasts no less striking. Unlike its transverse section, the length of a furnace has come to depend rather on the size of unit desired than on the requirements of smelting; and if the question of length be ignored, several of the various existing designs can be grouped together on the basis of a common transverse section. This section, having a width at tuyere level of 56 in. and a height above tuyeres of 18 ft., was developed at Great Falls, and the story of its development contains some interesting features. Ground was broken for the Great Falls works in the spring of 1891. About a year later, the concentrator was able to begin operation, followed within the next few months by the Brueckner, reverberatory, and converter departments, and in April, 1893, by the first blast fur-

Jan 1, 1914

By F. G. Clapp

Introduction.......................................................... 915 Scope of Discussion................................................... 915 Literature and Acknowledgments....................................... 915 Geographic Distribution of Petroleum in South America................. 916 Geographical Comparison with North America.......................... 917 Geological Inferences Regarding South America......................... 918 Quality of South American Oil........................................ 918 South America's Position in the World's Production.................... 919 Political Conditions in South America................................. 920 Peru.................................................................. 920 Distribution of Peruvian Fields................................ :...... 920 Surface Indications.................................................. 923 Geological Conditions................................................ 925 Quality................................................,............ 927 Production......................................................... 929 Argentina............................................................. 932 Distribution of Argentina Fields...................................... 932 Surface Indications.................................................. 933 Geological Conditions............:................................... 935 Quality .......................................................... 936 Production.......................................................:938 Venezuela................................................. 939 Distribution of Venezuela Fields...................................... 939 Surface Indications................................................. 939 Geology of Venezuela Fields.......................................... 941 Quality........................................................... 942 Production.......................................................... 943 Colombia.............................................................. 944 Distribution of Colombia Fields....................................... 944 Surface Indications.................................................. 945 Geological Conditions............................................... 948 Quality............................................................ 950 Production......................................................... 950

Jan 1, 1918

Jan 1, 1920

By Philip B. Bucky

[ ]

Jan 1, 1942

Jan 1, 1923

By B. E. Fernow

MINING interests in the Western mountains are very seriously affected by the danger to property and life from destructive snowslides and avalanches. This is a danger which the miner has largely brought upon himself by an improvident stripping of the timber from the mountain slopes, and, therefore, he might be expected to take an interest in the reforestation of the areas thus devastated. A canvass was lately undertaken by the writer to ascertain approximately the extent of the damage suffered from this source, but the difficulty of obtaining reliable data has proved too great to permit, as yet, even an approximation. So much, however, is certain : that the loss of life is considerable, and that much property is destroyed almost every winter. True, neither the number of avalanches, nor their destructiveness, nor the amount of loss compares with what Switzerland experiences. This is due not only to the greater precipitousness of the Alps and to different climatic conditions, but also to the fact that in Switzerland a larger number of settlements is exposed to these dangers. A very complete and interesting official report on the very numerous and destructive avalanches occurring in Switzerland during the season of 1887-1888 has just been published as a contribution to the inquiry, whether and how these dangers can be averted. Peculiar weather-conditions, in addition to heavy falls of snow, were the reasons for the frequency of the phenomenon during that winter. This report records 1094 avalauches, by which 850 houses were destroyed or severely damaged; 84 persons and 752 cattle were buried; traffic on railroads and on highways was greatly interrupted, and the damage to personal property alone was valued at over $100,000. One of these snow-masses covered about half an acre, with a cone 250 feet in height. During the same year in Tyrol the number of avalanches was 3647. Of these 1355 run over permanent beds; that is, they recur annually, so that they are

Jan 1, 1890

Jan 4, 1976

By A. H. Daane, B. J. Beaudry

The Sc-Y and Sc-Zr systems were studied by thermal and X-ray methods. Both systems are characterized by complete solid solubility in the low temperature hexagonal form and in the high temperature bcc form. In the Sc-Y system, there is a minimum in the solidus at 50 at. pct and 1365°C, while the solidus in the Sc-Zr system follows a nearly straight line relationship between the melting point of scandium and zirconium. There is a minimum in the temperature of transition from hexagonal to bcc in the Sc-Y system at 43 at. pct Y and 1175°C; while the temperature of transition is raised in the Sc-Zr system to a maximum of 1415 °C at 30 at. pct Zr. INTEREST in the metals of the first transition series has usually stemmed from their useful properties; however, there is now a great deal of interest in determining the fundamental nature of these metals. Since scandium is the first of these transition metals, a study of the preparation and Properties1 and the alloying behavior of scandium2 was initiated. In a continuing study of the alloying behavior of scandium, the systems of scandium with zirconium and yttrium have been established. Extensive solid solubility in both the Sc-Zr and Sc-Y systems was expected from application of the classical rules of Hume-Rothery. Also, the modified Darken and Gurry plot as suggested by Gschneid-ner3 showed ideal conditions for solubility in the Sc-Zr system with less favorable conditions in the Sc-Y system. The effect of scandium on the transformation temperature of zirconium and yttrium was of interest, since a recent empirical observation by Uly and Burr4 predicted that the solute scandium would raise the transformation temperature of zirconium and lower the yttrium transformation. In addition to noting the validity of the above predictions, the SC-Y and Sc-Zr systems were established. EXPERIMENTAL METHODS Materials. The metals employed in this investigation were crystal bar zirconium, distilled scandium prepared by the method described by Spedding, et al.1 and yttrium prepared by the method described by Carlson, et a1.5 The major impurities present in these metals are listed in Table I in ppm. Alloy Preparation. All the alloys examined were initially formed by comelting the two metals in a nonconsumable electrode arc-melting furnace under an atmosphere of purified helium or argon. The buttons were inverted at least five times and re-melted each time to ensure homogeneity. During preparation of Sc-Zr alloys, approximately 1 wt pct was lost which was attributed entirely to the loss of scandium by distillation. When preparing Sc-Y alloys, approximately 1.5 wt pct was lost, but it was assumed that the intended composition was maintained, since the relative weight lost when arc melting the component metals was nearly the same. Samples weighing 15 to 20 g were prepared for time-temperature thermal analysis, while only 1- to 2-g samples were prepared for the optical pyrometer and X-ray diffraction studies. Thermal Methods. The solidus and the melting points of the metals were determined by an optical pyrometer method described previously.2 The temperatures at which the transformation from hexagonal to bcc occurs were determined by differential thermal analysis. Several points on the solidus and liquidus in the Sc-Y system were also determined by this method and are in good agreement with those obtained by the optical pyrometer method. The procedure followed in the preparation of samples for thermal analysis and the furnace used have been described elsewhere.2'6 Since a limited quantity of scandium was available, most of the alloys were not melted during thermal analysis, thus avoiding contamination by the crucible. The alloy could then be reused and the composition changed by adding the desired quantity of solute to obtain the next alloy. Heat Treatment and X-Ray Methods. In order to ensure homogeneity, the "as arc-melted" alloys Were wrapped in tantalum foil, sealed in quartz capsules and heated at 1100°C for 15 hr and then cooled at a rate of 8 deg per min. Samples for X-ray diffraction were filed from these heat-treated alloys, sealed in 1/8 in. by 1/2 in. tantalum capsules under

Jan 1, 1963

By Robert W. Hunt

(Cleveland meeting, October, 1912.) PERHAPS of all the scientific economic questions which have been claiming the attention of capitalists, metallurgists, manu-facturers, directors of public utilities, and the general public of America, during the last few years, none have been of more importance than the one relating to the wear and safety of steel rails. The discovery of the Bessemer process made possible modern railway development. In that growth, as has generally happened in all progressive movements, ill its department have not remained equally balanced. Iron rails permitted the construction of roadways for the passage of power-driven vehicles. In time the speed and weight of such carriages proved too much for the wearing-qualities of the rails, and the limit of railway capacity seemed to have been reached. Bessemer made his invention, which was soon perfected and developed, especially as related to steel rails, and thereby increased the limit of capacity, acid vastly greater railway progress was, made possible. The Siemens-Martin open-hearth process followed, and was later supplemented by the Thomas-Gilchrist basic improvement. For a time the Bessemer steel rails of commerce Were, more than equal to all that was asked of them, but this did not long continue, as evidenced by the records in our Transactions. Revolutionary changes occurred in the industrial world, and in no part of it more than in steel-rail manufacture. Great and powerful commercial combinations were made, whose financial resources made possible the supplanting of the then most efficient blast-furnaces, steel-works, mid mills, by others of theretofore unimagined capacity. Old traditions and practices of steel-making were wiped away, and, in too many cases, output was apparently the chief aim, with the result that much dissatisfaction with the wear and safety of rails was felt by railway officials, and the general public was concerned as to its safety when traveling. The climatic conditions of the winter

Dec 1, 1912

By S. S. Clarke

THE opening of zinc-lead ore bodies in the lower chert beds of the Tri-State district, locally called sheet-ground deposits, [ ] presented several new economic operating problems to be solved before the low-grade deposits could be mined profitably. Drilling was the first high-cost problem and loading and haulage difficulties followed. At this time, the sheet-ground mines are producing about 2000 tons per day. GEOLOGY The geology and ore deposits of the Tri-State district have been covered in detail by [ ] Fowler and Lyden.* Briefly, the sheet-

Jan 1, 1942

By R. H. Johnson

All strata not yielding oil or gas in commereial quantities or a corresponding amount of water may be called dry in a wide sense. In petroleum geology, however, we may exclude all sands of too low or fine porosity to yield gaseous or fluid contents to the hole drilled in the sand before any original pressure that its contents may be under is disturbed. Most rocks are of this class and they are not reservoirs in our definition; their "dryness" is wholly a matter of course. What are the contents of the pores or what is the exact porosity of such rocks is of almost no concern to us, for economically they are "dry." What does interest us is the content of a rock having sufficient porosity and the pores of sufficient size to yield oil or gas in commercial quantities, if they were present under original pressure. Dryness of these reservoirs is a matter of supreme practical importance. Three views current as to such dryness seem, to me, to apply in a few cases only. It is the purpose of this paper to give reasons for this position and for believing that, in ordinary sedimentary rocks, there is only rarely a reservoir of competent porosity and undisturbed pressure that is dry in the sense of not yielding water, oil, or gas when first penetrated. 1. Gardnerl writes of some Kentucky sands, "There has never been present any salt water or other water in the sand." Absence of water cannot demonstrate this position. It is necessary to show that the rocks were not laid down in water, but in air, and that they became so enclosed, while still above the water-table of the ground water, that water has not been able to enter since. Most of these sands, and certainly the productive limestones, were deposited in water; and such sands as have been commercially productive show no reason for believing that the overlying shale or limestone was not laid down progressively from one direction and in water that would have flooded it. NO adequate explanation has been offered for this hypothesis, which is so inherently improbable. 2, Reeves2 urges that "sands originally water filled may have been drained of their water and not filled when later covered." It is difficult I James H. Gardner: Kentucky as an Oil State. Science, N. S. (1917) 46, 279-280. Reeves: Origin of the Natural Brines of Oil Fields. Johns Hopkins Univ. Circ., N. S. (1917) N. 3; Absence of Water in Certain Sandstones of the Appalachian Field. Econ. Geol. (1917) la, 354-378.

Jan 1, 1921

By Charles T. Holland

This discussion is concerned with those comparatively infrequent bumps that eject material from the failed mass with enough energy to wreck heavy machinery and seriously injure or kill people. In such cases there is a loud report, and the pressure waves set up in the mine atmosphere wreck ventilation controls several hundred feet from the site of the failure. Vibrations are induced in the earth's crust which may be detected several miles from the point of origin, and explosive gases may be released in large quantities.* Usually a dense suspension of dust is produced from the failed mass, together with dust placed in suspension by the resulting air blast. These rock bursts or bumps have also been called mountain shots, bounces, pillar bursts, and crumps. Such occurrences, when extensive, are serious catastrophes, and may force abandonment of the mine.1

Jan 9, 1958

By Samuel B. Christy

Jan 1, 1889

By Walter Herd

Fox the past eight years No. 2 mine of the Cumberland Railway & Coal Co., Springhill, Nova Scotia-a subsidiary of the Dominion Coal Co., Ltd.-has had an unenviable reputation for bumps. As the workings extended in certain directions under a greater cover, these bumps increased in severity and it became apparent that some change in the system of extraction was necessary if the mine was to continue to operate. In September, 1924, following several fatalities resulting from bumps, the Mines Department of Nova Scotia requested from the U. S. Bureau of Mines the services of George S. Rice, Chief Mining Engineer of the Bureau, to report on the conditions then prevalent in No. 2 mine, Springhill. This request was promptly and courteously granted. Mr. Rice made a full investigation and a comprehensive and helpful report, which is embodied in the 1924 Annual Report of the Department of -Public Works and Mines, Nova Scotia. Prior to 1925, the room and pillar method was employed and in January of that year (there being a cessation of work from March to August due to labor troubles) longwall retreating on the west side, on a limited scale, and in a small section on the east side of the mine was started. The major portion of the east side was not operated on this system till August, 1926, as there was developed a considerable area ready for pillar extraction between an arbitrary boundary and a point up to which bumps of any consequence, had not been experienced. In the interval development work for longwall retreating below the 5900-ft. level was vigorously- pushed. This longwall retreating system was suggested by Mr. Rice as a possible remedy and was heartily endorsed by the company officials. This paper describes the conditions and happenings subsequent to Mr. Rice's report and more especially the results with the longwall retreating system of mining under the peculiar circumstances pertaining to mining. No. 2 Seam, Springhill, at depth, and records the 'conclusions which experience with several severe bumps under this mode of extraction would suggest. Except where necessary to make the paper intelligible as an entity any duplication of Mr. Rice's report will be avoided.

Jan 1, 1929

By Thomas Harris

This paper. was written in conjunction with the work being undertaken by the Technical Committees on Classification of Coal, and an effort has been made to compile information relative to the use of coal for stationary steam generation in order to use this information to assist the Committee on Classification of Coal for the ultimate purpose of elimination of losses both by the' reduction of indivi-dual effort and waste in the consumption of material. Under the auspices of the National Association of Purchasing Agents, a questionnaire was drawn up to develop this information from stationary steam plants throughout the United States. in order to consolidate the information de-veloped from the many hundreds of boiler tests on coals consumed by various coal¬burning equipment. These questionnaires covered: 1. The company reporting, location and method of delivery to the plant. 2. Complete coal date, including description of coals used (with. sufficient space to- include first, second and third, preference) on--source of coal used,- complete-analysis and factors affecting choice of, coal used. 3. Plant data, divided into - A. Hand fired, B. Overfeed stokers,. . C. Underfeed stokers, D. Traveling grate stokers, E. Pulverized coal, and included complete description of furnace data, draft data, coal-burning rate, type of stoker, type of pulverizer, efficiency date and remarks.

Jan 1, 1933