Search Documents

By Frederick Sharpless

THE term "segregation," as here used, means the separation of certain natural resources into groups, consisting of one or more members, with the idea that when thus segregated, each group may be more easily and effectively administrated. We may, for example, consider surface rights as distinct from underground rights, and stop there; or we may go further, and deal separately with timber, water, and agricultural rights, or, going underground, we might deal separately with such groups as precious and base metals, clay, oil, gas, etc. The present paper contemplates only the separation so far as practicable, for administrative purposes, of surface from mineral rights. "Classification," in this paper, has reference to the groups into which the government has divided, is dividing, or will hereafter divide its natural resources; first, into the broad classes of mineral and agricultural lands; and, second, into coal, oil, phosphate, brine lands, etc., the central idea being the separation into natural groups for the purpose of simplifying administration and for the purpose of encouraging maximum development and minimum waste. The two subjects are in some respects quite distinct, but as my argument develops, I think it will be obvious why they are discussed in the same paper.

Jan 4, 1914

By John A. Fagnant

At Elkol, Wyo., about 80 miles northeast of Ogden, Utah, the Kemmerer Coal Co. and the Utah Power and Light Co. are involved in a joint venture that will soon see 1 million tons of coal going "out by wire" to Ogden. Kemmerer, owner of a multi-seam strip mine, and the utility, now building a steam power plant adjacent to the mine site, expect to begin initial power generation by February 1963. Although capable of producing only 150,000 kw at that time, this plant is expected to be ultimately enlarged to 500,000-kw capacity which will require about 2 million tons of coal annually. The deposit consists of more than 30 seams of coal, usually varying in thickness from 2 to 40 ft, and separated by beds of sandstones and shales. In certain areas the aggregate thickness of all the coal seams measures 300 ft. The thickest and most spectacular of these seams is the lowest one, referred to as the No. 1 seam, which is 118 ft thick in some places.

Jan 8, 1962

By Oswald J. Heinrich

THIS question having been repeatedly raised, and particularly revived in a discussion at the last meeting of the Institute, I beg to submit the following remarks, based partly upon personal experience, partly upon the results of large works in Europe, establishing, years ago, the practicability of certain methods, which may therefore be considered to have passed the stage of mere experiment. Before entering upon the merits of one system or the other, it is indispensable to lay down some recognized principles, which ought to serve as guides, in arriving at fair judgments in questions of this character. In a profession like that of mining, locally so much influenced by combinations of circumstances too various to mention, it is difficult to do more than lay down the main features of a system based upon general laws and recognized facts, leaving the details to the sound judgment and experience of the engineer, who, by virtue of his education, ought to be able to make such choice and such modifications in the plans of a mine as the particular case demands. Mineral resources, in some countries the sole property of the owner of the soil, in others controlled by the strong hand of a government, are nevertheless a gift of nature, in which, indirectly, the whole of the human race has as real an interest as the immediate owner himself. This interest requires, at least, that no unnecessary waste of

Jan 1, 1874

By J. W. Spretnak, V. Kandarpa, G. W. Powell, R. A. Erickson

Neutron-diffraction pattens were obtained at room temperature from two austenitic manganese steels, oxc wth n carbon content of 1.23 zct PC/ and the olher 0.63 wt pct. Analysis of the data showed that the curOan atols (ions) occupy tile octaheadral site. any of the cavbon is in the tetahedral site, tile concentration is too strzall lo be detecled by tzeulr-on d$facton. AS part of a long-range investigation of eutectoid decomposition, a study of the structure of austenite has been undertaken in order to characterize as best as possible the parent phase in the Fe-C system. Austenite is a solid solution of carbon atoms in fcc iron, the carbon atoms being located in interstitial positions. Of the two kinds of interstitial sites, octahedral (0, +, +) and tetrahedral (4, a, $), in this lattice, the larger octahedral sites are usually considered as the probable position of carbon. The strain energy involved in pytting a neutral carbon atom (covalent di; ameter 1.54)' into a tetrahedral site (diameter 0.56A) is considerably greater than that associated with p2tting carbon into the octahedral site (diameter 1.08A). Dayal and arkeen' observed the migration of carbon in iron under the influence of an electric field indicating tha tye carbon is ionized. pe ionic radius of C'4 is 0.15A and that of C" is 0.29. Consequently, it is conceivable that carbon ions could occupy the tetrahedral sites if one considers only the strain energy. Size considerations alone do not provide a complete explanation for the formation of the interstitial solid solutions, however. because metals such as copper, zinc, and cadmium do not appear to form interstitial solid solutions in spite of their large interstitial sites. Evidence which suggests partial ioni-zation of the carbon in austenite has also been obtained by Speiser, Spretnak, and alor who derived formu- lae relating the observed change in lattice parameter to the effective diameter of the solute atom. Assuming the carbon occupies the octahedral site. they computed the effective diameter of carbon to be 1.33A whereas the covalent diameter is 1.54A. petch5 concluded from powder X-ray diffraction experiments that carbon atoms occupy the octahedral sites. His conclusion was based on the general trend observed in the intensity of the diffraction lines as the carbon content of the austenite was increased. However, the major difficulty associated with application of X-ray diffraction to this particular problem is the relatively poor scattering power of carbon. Williamson and smallman' utilized X-ray diffraction to study the line broadening caused by the strain field about carbon atoms inferrite: these investigators concluded that at least 85 pct of the carbon in ferrite occupies the octahedral (0: 3, B) site rather than the larger

Jan 1, 1967

By C. Morrow

Deformation studies were performed on tuffaceous rocks fran Yucca Mountain, Nevada Test Site to determine the strengths and coefficients of friction under confining pressures from 10-50 MPa at room temperature. Frictional strengths of 30ºsawcut samples increased with pressure and reached values of around 150 MPa at the higher confining pressures. However, the failure strengths of the intact samples were quite unpredictable. The coefficients of friction ranged between 0.7 and 0.9 for all specimens. These data can be used in conjunction with in situ stress measurements at Yucca Mountain, to evaluate the potential for earthquake activity in the region.

Jan 1, 1984

By Herbert Clark Hoover, Lou Henry Hoover

THE third book has explained the various and manifold varieties of veins and stringers. This fourth book will deal with mining areas and the method of delimiting them, and will then pass on to the officials who are connected with mining affairs'. Now the miner, if the vein he has uncovered is to his liking, first of all goes to the Bergmeister to request to be granted a right to mine, this official's special function and office being to adjudicate in respect of the mines. And so to the first man who has discovered the vein the Bergmeister awards the head meer, and to others the remaining meers, in the order in which each makes his application. The size of a meer is measured by fathoms, which for miners are reckoned at six feet each. The length, in fact, is that of a man's extended arms and hands measured across his chest ; but different peoples assign to it different lengths,

Jan 1, 1950

R. W. Raymond, New York, N. Y.: Mr. Bain's introductory statement that there is a growing disposition on the part of the public " to change emphasis " in government from political equality " to " social justice " is somewhat vague; but I gather from his argument that he approves the growing disposition to which he refers, and that the " emphasis " which it demands involves a radical change in the policy hitherto pursued by the United States—the policy under which the Pacific States and Territories have been developed thus far. I do not understand how "social justice" is to be furthered by the sacrifice of " political equality," or how the change is to be effected by "emphasis." But I fancy that the beneficent and necessary

Jan 1, 1913

By Harmon D. Nine

DISCONTINUITIES in the strain vs cycles to failure (S-N) fatigue curves have been reported for polycrystalline materials by Porter and Levy for copper,&apos; by Benham and Ford for mild steel,&apos; and by Williams and Stevens for 18/5 stainless steel.3 However, the considerable scatter of the points for polycrystalline materials have made a statistical analysis of the data necessary to confirm the discontinuities. By using oriented single crystals of high-purity material and low grown-in dislocation content, the reproducibility has been improved to a degree which makes statistical analysis unnecessary and clearly shows discontinuities in the S-N curves. A recent publication4 reports an abrupt change of slope in the S-N curve for ( 100) axially oriented copper single crystals fatigued in torsion. The reported discontinuities in the S-N curve, along with a different mode of failure in the two branches of the curve, have been interpreted as being due to two different amplitude-dependent mechanisms. Further work on copper single crystals of (111) axial orientation has now been completed which supports the existence of an amplitude-dependent change in the mechanism of fatigue. In the present study torsional-fatigue experiments were performed at room temperature in air on (111) axially oriented single crystals. The crystals were grown and prepared as reported in Ref. 4. Two different methods of growing the crystals also discussed in Ref. 4 produced crystals of two different perfections: Type I with dislocation density of >l06 per sq cm and Type I1 with dislocation density of <l05 per sq cm. In accordance with the accepted hypothesis that crystal flaws are primarily responsible for the scatter of fatigue lifetimes, particularly at low amplitudes, the values for the three lowest amplitudes for Type I crystal are believed to be uncertain. They are marked in braces in Fig. 1. On the other hand, at amplitudes above a surface shear strain (SSS) of *0.003, the data for both types of crystals are in agreement. Most remarkably the S-N curve for torsional fatigue of (111)-oriented single crystals is composed of three segments separated by rather large discontinuities, Fig. 1. Metallographic and X-ray measurements indicate that the lower branch corresponds to the low-amplitude (F) region of the (100) copper single-crystal results as discussed in Ref. 4, and the two upper branches correspond to the high-amplitude (H) region. The lower discontinuity in the (111) S-N curve and metallographic evidence give further support to the hypothesis that different mechanisms of failure operate for high and low strain amplitudes. Reference to the resolved shear stress diagram, Fig. 2, shows that the highest stressed systems in

Jan 1, 1965

Abadilla, Quirico A., Geol.. Lago Pet. Corp Box 172 Maracaiho, Venezuela. IIAbbw. Robert Graham. The W. W. Sly Mfg. Co.Train Ave.. Cleveland. Ohio. Abbotf A. N., Mines Supt., Maznpil Copper Co.. Ltd..Conception del Oro, Zac., Mexico. Abbotf Clarence E, Mgr.. Mines & Quarries, Tenn. Coal. Iron & R. R. Co., 1242 Brown Marx Bldg., Birmingham, Ala. Abbott. Louis Benjamin. Chief Engr.. Consolidation Coal Co. ... .Elkhorn Div., Jenkins, Ky. Abeel, George 8.. Jr., Cons. Min. Engr...4612 West 17th St., Los Angeles, Cal. Abel. Albert E.. Asst. to Pres.. Valley Mould & Iron Corp..Hubbard, Ohio. Abel. Raymond L Asst. Prof., Dept. of Pet. Refin.. Univ. of Pittsburgh. .. .Pittsburgh. Pa. Abernathy. George Elmer. Prof. of Geol. & Min.. Kansas State Teachers College. Pittahurg. Kans. Abernethy, D. Carl, Jr. Min. Engr., Hudson Coal Co. .Scranton, Pa. Abw, Hirouhi. Min. & Met. Engr., Min. & Met. Dept., The Higher Technical School, Osaka, Japan. Aborn. Robert H.. Research Assoc.. Mass. Inst. of Tech..Cambridge, Mass. Abouchar. Bylvain Sley. Min. Engr. & Geol., c/o S. H. Sekaly, 13 Rue El Nimr, Cairo, Egypt. tAbozeid. Mahmood. Pet. Min. Engr., Marland Oil Co. of California, Subway Terminal Bldg., Los Angeles, Cal. Abraham. Arthur W.A. pt. 40, Barcelona. Anzoatmui, Venezuela. Abrahams. Alexander I.. Gen&apos;l Mgr., Racon Electrical Co.. ..... .Slough, London, England. tAbrahamuon, C. W., Min. Engr.. The Mond Nickel Co., Ltd.. ..... .Levack. Ont., Canada. Abstein, Henry T.. Engr. & Mgr.. Profile-Tamarack Mines Co.. ...... .Yellow Pine, Idaho. tAcker, E. WC.. Met.. ........ .I28 East Washington Lane. Germantuwn. Philadelphia, Pa. IlAckerman, D. E.. Research Engr.. Research Lab., International Nickel Co., Bayonne, N. J. tAckerman. Ernest R., Pres., Lawrence Portland Cement Co.. . .Plainfield, Union Co., N. J. Adachi. Jinzoo.A..d dress Wanted Adachi, Yuichi, Chief Engr.. Anzan Steel Works, South Manchuria RY. Co., Anzan, South Manchuria. China. (Via Dairen). Adair, Arthur C, Valuation Engr., Internal Revenue. Treasury Dept.. . .Washington, D. C. Adami. Arthur E., Prof. of Min. Engrg., Montana State School of Mines. Butte, Mont. Adami. Charles J.. Min. Engr., Gen&apos;l Mnr., St. Jos~ph Lead Co.. ....... .Bonne Terre, Mo. Adama, C. W., Pres. Adams Pacific Corp .I66 Montgomery St., San Francisco. Cal. Adams. Cuyler .Dee rwood, Minn. Adams, David T, 514 Wrigley Bldg.. Chicago, Ill. ADAMS, FRANK DAWSON, Logan Prof. of Geology and Dean, Faculty of Applied Science. McGiU Univ., Montreal. Que.. Canada. Adams. Gale L, Research Engr.. General Pet. Corp...Los Angeles. Cal. Adams. George I.. Prof. of Geol. & Mineralogy. Univ. of Alabama. .Tuscalmsa, Ala. Adams. H. H.. Cons. Gml..Room 415, W. T. Waggoner Bldg., Fort Worth. Tex. Adams, Henry, Cons. Min. Engr. . 934 Park Ave., Plainfield, N. J. Adame, Henry H. 285 Madison Ave., New York. N. Y. Adams. Henry Farnum. Engr.. Charge Experimental Work, Inspiration Concentrator. Inspiration Cons. Copper Co.. Box 364, Inspiration. Ariz. Adams, Huntington, Min. Engr, 149 Broadway, New York, N. Y. Adams. Leland D, V.P.. Leslie-California Salt Co., 166 Montgomery St.. San Francisco. Cal. Adams. Louie W.. Illinois Steel Co Gary, Ind. Adama, XL L. Min. Engr.. Old Ben Coal Corp., Mine 12.. Christopher. IU. Adams, Robert M. Robert M. Adam Co. .I201 Fidelity Bldg., Duluth, Minn. Adams. Sidney F.. Geol., Empire Zinc Co .Gilman, Colo. tAdams, Waldo Peck..P ittsfield, Pike Co.. Ill. Addams. Charles 1. Min. Engr.. Bo x 663. Phoenix, Ariz. Addicka, Lawrence. Cons. Enar..... .61 Maiden Lane. New York. N. Y. Addison, Herbert, V.P.. Big Horn Collieries Co ,412 Colorado Bldg., Denver, Colo. Adkemn. J. Carson. Min. Engr.. HY Grade Manganese Co., Inc..Woodstock, Va. Ady. Joseph Wesley. Jr.. Min. Enar., 314 Mining Exchange Blda., Colorado Springs, Colo. Affelder. William Lewis. Asst. to Pres., Hillman Coal & Coke Co. & Allied Companies. 2006 First National Bank Bldg.. Pittshurgh, Pa. Ameck, B. F.. Pres.. Universal Portland Cement Co. .. .210 South La Salle St., Chicago. Ill. Agabeg, Edgar C.. Cons. Min. Engr.. ..... .Evelyn Lodae. Asansol, E. I. R. Bengal, India. tAsar. William M.. Aest. Prof. of Geol.. Kirtland Hall, Yale Univ.. ... .New Haven, Conn. Agaeniz. Rodolphe L, Pres.. Calumet & Hecla Consolidated Copper Co. ...... .Boston, Mass. tAgens, William Holmes. District Mgr.. Traylor Engrg. & Mfg. Co., 362 I. W. Hellman Blda.. Los Aneeles. Cal.

Jan 1, 1928

By Byron B. Morton

NICKEL-BEARING alloys are associated with petroleum in the fields of exploration, production, and refining. In the first- named field the geologist of today makes use of such instruments as the seismograph, torsion balance, and magnetometer, the selection of proper alloys and metals for the manufacture of which is an important matter. Nickel-bearing alloys are useful for parts that require resistance to corrosion or that must have non-magnetic properties. Where special co- efficient of thermal expansion are de- sired, they are obtained by using alloys high in nickel (20 to 60 per cent), since, by varying the nickel contents, alloys can be obtained ranging fro111 "Invar", with a low expansion between -40 and 175 cleg. F., to those with coefficients of expansion exceeding that of steels. The latter are obtained by additions of chromiurn to the alloys. Alloys containing 50 to 80 per cent of nickel, which possess high magnetic permeability, find application in certain instruments where this property is important.

Jan 1, 1935

By Jack Fox

Last time there was a Take Five in these pages, it dealt largely with the matters considered by your Board of Directors at the meeting on October 20, 1970, in St. Louis, Mo. It was impossible to cover all the points worthy of discussion in the space available. So, at the end of the Take Five in the December issue of [i=], I promised to continue in the next installment. Unfortunately, I was unable to keep that promise. On December 2 your humble servant joined the ranks of those who have suffered a coronary occlusion. While I was away from the office, the very excellent SME staff team that we have built up over the years kept things going without bothering the "old man" unnecessarily. Assistant Executive Secretary, John V. Beall, Mrs. Lillian E. Donaldson, Assistant to the Executive Secretary, Mrs. Ruth Orologio, Administrative Assistant, and Mrs. Alice Ruiz exceeded even their usual dedicated efforts. As a result, the SME came up to the Centennial-Annual Meeting in great shape.

Jan 1, 1971

By Alfred H. Bell

The upswing in oil production and drilling activity in Illinois that began in 1937 gained momentum in 1938 and promises to bring a new and higher peak in the state&apos;s annual production in 1939. In 1938 the production totaled 23,929,000 bbl., as compared with 7,426,000 bbl. in 1937, more than a threefold increase. The number of producing oil wells in the new fields was 230 at the end of 1937 and it increased to 2157 at the end of 1938. Daily production for the whole state increased from approximately 35,000 bbl. at the end of 1937 to approximately 135,000 bbl. at the end of 1938, nearly a fourfold increase. Of a total of 2539 wells completed in 1938 in Illinois, 1984 produced oil, 26 produced gas and 529 were dry holes. Of the total, 377 are classified as "wildcat" wells, defined as wells drilled outside of proved territory and more than one mile from the nearest production. The remainder, 2162 wells, were drilled in or near proved fields. Of the 377 wildcat wells (Table 2) 32 were successful in discovering oil or gas in commercial quantities, either new fields or extensions of old fields. Four of these discovery wells mere gas wells, which are not yet commercially productive owing to lack of pipe-line facilities. A special effort was made to ascertain the reasons for the locations of as many as possible of the wildcat wells and the results of this investigation are set forth in the following table:

Jan 1, 1939

By Alfred H. Bell

The upswing in oil production and drilling activity in Illinois that began in 1937 gained momentum in 1938 and promises to bring a new and higher peak in the state&apos;s annual production in 1939. In 1938 the production totaled 23,929,000 bbl., as compared with 7,426,000 bbl. in 1937, more than a threefold increase. The number of producing oil wells in the new fields was 230 at the end of 1937 and it increased to 2157 at the end of 1938. Daily production for the whole state increased from approximately 35,000 bbl. at the end of 1937 to approximately 135,000 bbl. at the end of 1938, nearly a fourfold increase. Of a total of 2539 wells completed in 1938 in Illinois, 1984 produced oil, 26 produced gas and 529 were dry holes. Of the total, 377 are classified as "wildcat" wells, defined as wells drilled outside of proved territory and more than one mile from the nearest production. The remainder, 2162 wells, were drilled in or near proved fields. Of the 377 wildcat wells (Table 2) 32 were successful in discovering oil or gas in commercial quantities, either new fields or extensions of old fields. Four of these discovery wells mere gas wells, which are not yet commercially productive owing to lack of pipe-line facilities. A special effort was made to ascertain the reasons for the locations of as many as possible of the wildcat wells and the results of this investigation are set forth in the following table:

Jan 1, 1939

By J. T. Norton, J. G. McMullin

E. R. JETTE*—The way this ternary was developed there are two directly determined points on each of the iso-thermals except the 700° isothermal, where I believe there is only one. How were the end points determined, and what was the basis for it? Whose work formed the basis for the silver copper line ? M. B. BEVER †—At most temperatures the authors determined three points of the isothermal line. For example it can be seen from Fig 3 and 4 how three points for the 600°C contour line were obtained. The authors took two additional points for each temperature from the copper-silver binary diagram contained in Hansen&apos;s volume on constitution diagrams. It is correct that the 700°C contour line is based only on one point in the ternary field which was found by a slight extrapolation of Fig 4. R. I. JAFFEE*—Are the tie lines representing phases in equilibrium parallel to the silver-copper boundary ? M. B. BEVER—Are you asking that as a matter of principle ? R. I. JAFFEE—I assumed that would follow from principle. I wonder if that is in accordance with the authors&apos; ideas too. M. B. BEVER—I do not believe the authors obtained any information on the tie lines in the two-phase field. Of course, in the limiting case of very low gold contents the tie-lines approach to the silver-copper boundary, but generally in the two-phase field I do not think that the tie-lines have to be parallel to the boundary. E. R. JETTE—I am quite sure they do not have to be parallel. You cannot tell from this work in which direction they go. E. A. GULBRANSEN*—Were any pycnometric measurements made to check the lattice parameters of the alloys ? M. B. BEVER—I did not hear any-

Jan 1, 1950

By J. A. Roberson, Robert A. Rapp

From the observation of platinum wire marker movement in the oxidation of columbium at high lemperatures and low oxygen pressures, predonzinant cation diffusion in CbO, has been demonstrated. The Cu,0 molecule was used as an oxidizing species to study the nature of the porous scale and the location of the reduction site in the oxidation of colum-bium. The Cb205 scale contains microporosity and forms by alternate ionic diffusional growth and fracture. The oxidation of columbium at high temperatures and very low po, results in a relatively compact and protective Cb205 layer. THE observation of marker movements during oxidation is one means for the identification of the mobile ionic species in an oxide lattice. Previous marker experiments in the oxidation of columbium have all resulted in the markers being found on the outside surface of the Cbz05 scale. The Cr203 powder markers of Klopp et a1.,&apos; the gold film marker of Kofstad and ~jijllesdal,&apos; and the platinum wire marker of Cathcart et a1 .3 were found at the oxide/gas interface for oxidation temperatures ranging from 450" to 120O0C. However, in all experiments relatively high oxygen pressures were used. As discussed by Mrowec, even the interpretation of marker experiments in simple scales containing only one compound is not without ambiguities. In brief, it can be said that a marker may be found almost anywhere in the scale layer if the metal oxidizes by cation diffusion through the scale; the position of the marker depends upon morphological happenings in the scale. When considering marker movement in a polyphase scale one must proceed with extreme caution. For example, in the past (and present) work markers have never been found at the columbium-scale interface, and one might infer that the oxygen ion is mobile in CbO and CbO,. However, only trace quantities of CbO and CbOz have been present on any of the specimens, so no firm statement is justified on this basis. Despite previous experimental work, considerable doubt still exists concerning the role of the oxides CbO and CbOz in the oxidation of columbium. The identification of the mobile ionic species in CbO and CbOz from the observation of platinum wire markers was one goal of the present investigation . The linear kinetics of columbium oxidation at high temperatures (T - 1000°C) suggests that the Cbz05 scales which form on columbium are porous. From mercury absorption measurements on a Cbz05 scale formed at 500"C, Aylmore et al.&apos; reported a minimum volume fraction of connected voids equal to 0.15. While these scales often appear to be quite porous when viewed in metallographic cross section, they are so brittle that metallographic preparation is likely to exaggerate any porosity originally present. In this investigation, porosity developed during the oxidation of pure columbium and present at the high temperature was detected by oxidizing specimens in sealed evacuated capsules containing large compacts of mixed copper and CuzO powders. wooda has demonstrated that the CuzO, or (CuzO),, molecule is volatile and that oxygen is transferred by the CuzO molecule from a Cu/CuzO mixture to materials having a greater affinity for oxygen. For each molecule of CuzO that is reduced at a sink for oxygen, two atoms of copper are deposited. Quantitatively, essentially all of the oxidation carried out by a Cu-Cu20 compact results from a displacement reaction involving the CuzO molecule. When a metal which oxidizes to form a porous scale is exposed to the CuzO vapor, the CUZO molecules are reduced in the pores leaving a deposit of metallic copper to mark the site of the reduction. This technique has the rather unique advantage that any copper-coated pores found in the scale are unambiguously related to the reduction site in the growth of the scale under consideration. Pores or cracks which form in a msition*- external to the reduction site or which occur as a result of cooling or handling of the specimen will not exhibit the copper deposit. EXPERIMENTAL PROCEDURE Marker experiments were made on columbium metal, and on pellets of CbO which had been pressed and sintered. Platinum wire markers (0.001 and

Jan 1, 1968

By Edwin B. Wilson, Joseph W. Leonard, Richard W. Borio

preparation of specification coals for the utility industry is approached from the standpoint of a cooperative effort with the power company to assure that the shipped product will be a noncorrosive coal. Selective mining, coal preparation, the use of additives, and coal blending are mine-site techniques proposed as means for upgrading corrosion-retarding constituents of utility coals (CaO and MgO) while, at the same time, reducing the concentration of those constituents of coal (Na20 and K,O) which cause corrosion. Data obtained from large-scale boiler testing in combination with bench-scale physical and chemical tests are used as a basis for the formulation of mine-site procedures to improve coal combustion utilization. Electric power generation remains the greatest market for coal in the United States. A major reason for this strong market has been the ability of the coal industry to supply a superior product for combustion while maintaining competitive prices. Now that the coal industry is engaged in intensive competition with nuclear power for future energy demand, it becomes ever more imperative that superior coal products are produced. One important problem when burning some coals is a liquid phase corrosive attack on boiler tube metal in the superheater and reheater areas of the furnace where steam temperatures may exceed 1050°F. In addition to causing power outages and high maintenance costs, corrosion is a continuing barrier to the future development of more efficient steam cycles which permit lower generation costs when using coal. Research methods of the past which have been directed at finding solutions which could be applied at the power plant site have been only partially successful and are generally costly. This paper contains a suggested --method of corrosion control through investigation of the problem at the source of the trouble—the coal supplier facility. It is proposed that mine-site pre-ventative procedures be considered as an effective means of cooperative corrosion control between the power company and the coal supplier. Economic justification must be applied to the individual situation. This paper is based on recent work by Combustion Engineering, Inc. and the Coal Research Bureau of West Virginia University under a contract from the Department of the Interior Office of Coal Research.&apos;,&apos; Results which are of importance to this discussion may be summarized as follows: 1) The alkali minerals of coal (Na2O and K2O), as measured by an acid leaching process, can be related to corrosion rate in utility boilers. As these constituents increase in a coal product, its corrosiveness can be expected to worsen. 2) The alkaline-earth minerals contained in coal, reported as total CaO and MgO reduce corrosiveness 2s their concentration increases. 3) Naturally occuring, alkaline-earth-bearing materials, such as limestone and dolomite, may be added to a coal to reduce its corrosiveness. 4) Coals with very low iron contents tend to be less corrosive. These results provide the groundwork for examination of the system of operations which occur at the supplier facility from the seam face where mining is begun to the point of loading for shipment. The Mining System Fig. 1 is a cross section of one of the typical coal seams (designated coal A) that was boiler tested during this research program. This seam is overlain by material which consists primarily of a gray-black shale. In the lower third of this seam, there exists a thin rock parting of less than 4 in. in thickness which is consistent throughout the seam. The floor material is fireclay. In order to examine mineral distribution throughout this particular seam, the Coal Research Bureau collected a

Jan 1, 1971

In 1974, iron pellet production in the Great Lakes region reached the 53-million-tpy level, accounting for more than 88% of the nation&apos;s pellet production. By 1978, pellet output from the Great Lakes district will climb to at least 78 million tpy. To achieve this 50% increase in output, the US iron and steel industry is investing at least $1.25 billion in new mines and pelletizing plants, mostly in Minnesota and Michigan. The biggest effort is concentrated in the Mesabi Range of Minnesota, the heart of the US steel industry&apos;s major iron ore source: here, plans for two new taconite plants-one by Hibbing Taconite Co., and the other by Inland Steel Mining Co.-and three major expansions of existing facilities are already under way to boost Minnesota&apos;s total iron pellet capacity from the current 41.2 million tpy to 65 million tpy by 1978. The facilities being expanded are those of US Steel Corp. (Minntac operations), Eveleth Taconite Co., and National Steel Pellet Co.

Jan 11, 1975

Uranium was the prima donna of 1978, and the exploration pace was fast and furious in traditional uranium producing areas such as the Powder River Basin, Grants mineral belt, San Juan Basin, and Uravan mineral belt. Adding fuel to the fire were several significant discoveries: The Date Creek Basin of western Arizona, the McDermitt caldera of northern Nevada, and Tallahassee Creek in Colorado&apos;s intermontane basin. Advances in solution mining haw resulted in deeper drilling on the Texas Coastal Plain, and the price of uranium has encouraged widespread exploration in frontier areas and non-sandstone environments.

Jan 5, 1979

By J. Ruben Velasco, Roland B. Mulchay

CANANEA has long been recognized as a remarkable field for geologic study. The copper deposits and rocks of the district have been described by many geologists and engineers, but only the most general correlations have been made between Can-anea sedimentary rocks and other known sedimentary sections in the southwestern United States and northern Mexico. The present paper describes the Cananea sediments in greater detail than has been done before and attempts to fit the Cananea sedimentary section more closely into the geologic time table. The lack of well-preserved fossils has made it difficult to date the sediments accurately in geologic time, but it is possible to make tentative correlations between the Cananea sediments and the southeastern Arizona sections, based largely upon lithology and general position in the geologic column. It appears that sedimentation at Cananea and Bisbee may have been closely similar during Paleozoic time. Even such generalized correlations, however, may be subject to considerable modification in the future. The present study has led to the recognition of other problems of age and mineralization relationships in the Cananea district. Cananea is located in the north-central part of the state of Sonora, Mexico, at an elevation of 5270 ft. It is about 135 miles northeast of Hermosillo, the state capital, and 25 miles south of the international boundary. By road Cananea is 40 miles from the twin towns of Naco, Ariz., and Naco, Sonora, and about 50 miles from Bisbee, Ariz. It is served by the Nogales-Naco branch of the railroad, F.C. Pacifico, and is connected with Chihuahua and Mexico City by the Aeronaves airline. The headwaters of three rivers flowing to the Gulf of California are located in the Cananea Mountains: the San Pedro River, flowing to the north; the Sonora River, flowing south and west; and the Mag-dalena River, flowing west. Elenita Mountain, the highest point in the district, has an elevation of 8140 ft. The Cananea Mountains extend in a series of north-south to northwest-southeast spurs and ridges and are surrounded by gently sloping gravel plains. The mineralized area, lying across the southern and central parts of the range, is about 6 miles long and at most 2 miles wide. Elevations at the mines vary from 5300 ft at Cananea-Duluth mine at the southeast end of the district to between 6000 and 7000 ft at the west end of the mineralized area at Puertecitos-Elenita mines. Principal production has been from the intensely mineralized and altered area of Capote Basin in the central part of the district and the immediately surrounding area to the southeast. The district has produced over 2 billion lb of copper, substantial molybdenum, and minor amounts of lead, zinc, silver, and gold. Total production through 1949 is estimated at more than $300 million. In 1900 large-scale development was started at Cananea by W. C. Greene. Until World War II only high-grade ores were exploited; low-grade ores were extracted after the installation of a large concentrator in the early 1940&apos;s, and subsequent operations have been based upon mining and processing ores containing less than 1.0 pct copper from open-pit and underground workings. Mining and concentration of such low-grade ores, however, are made possible only by continued high copper prices, and active exploration for high-grade orebodies has been continued throughout the important mineralized areas. General Geology Study of the involved rock pattern at Cananea has indicated a complex geologic history for the district. Widespread alteration and mineralization have masked many of the salient features and have led to widely varying geologic interpretations over the years. Further work will probably disclose new information which will modify current beliefs. At Cananea a conformable series of sediments of probable Paleozoic age was deposited on an unknown basement. Following Paleozoic time there was an extended period of erosion common to many districts in the southwestern U. S., and there is no present evidence of marine sedimentation at Cananea after the Paleozoic. The eroded surface was eventually covered with a great thickness of extrusive volcanic rocks. The entire series of sediments and volcanic rocks was later intruded by a variety of deep-seated igneous rocks. These included the Cananea granite, the Cuitaca granodiorite, the El Torre syenite, the Tinaja diorite, the Campana diabase and gabbro and the Colorada rhyolite quartz porphyry. Faulting of early age, probably prior to the deposition of the volcanic rocks, may have been responsible for the present position of some of the intrusive rock masses. In the Capote mine on the third and fourth levels the northwest-striking Rick-etts fault zone, with apparent offset of about 800 ft, has been sealed by a dike-like mass of Cananea granite which gradually increases in size with depth. In lower levels of the mine the granite forms a large southeast-plunging mass generally following the course of the Ricketts zone. The granite is not known southeast of the Capote-Oversight mine areas and the Ricketts fault does not appear in the vol-canic~ southeast of Capote Basin, but several plugs of Colorada quartz porphyry cut the volcanics along the assumed general southeast trend of the Ricketts zone. These porphyritic intrusives may be the up-

Jan 1, 1955

By William H. Mount

St. Joe Minerals Corp. has a long operating history of utilizing rubber-tired, trackless mining equipment in its Southeast Missouri Lead Belt underground mines. The company&apos;s first completely trackless mine, Hayden Creek, was opened in 1952, employing rubber-tired drill jumbos, electric shuttle cars, and articulated diesel trucks. The trucks were comprised of a conventional scraper tractor unit matched with a rear-dump rock wagon. These machines featured the first true earthmover tires to be used underground by St. Joe. The articulated truck concept proved to be very successful, and constitutes an increasing portion of the underground haulage today. St. Joe&apos;s second completely trackless mine, the Indian Creek property, was opened in 1954; conventional 9.1-t (10-st) rear dumps were used for haulage. Main haul roads were designed to be wide and fairly level to accommodate speeds of 32-40 km/h (20-25 mph).

Jan 4, 1976