Search Documents

By W. Spencer Hutchinson

IT is the purpose of this paper to describe a method used to determine the corundum contents of samples of hard crystalline gneiss containing both corundum and red garnet. A chemical analysis of the rock for alumina would not fix the amount of corundum because at least three other constituent minerals of the rock, mica, feldspar, and garnet, contain alumina combined with silica. Following are the principal minerals found in the samples, together with their specific gravity and hardness as given by Dana:

Jan 6, 1913

By Klaus Schwerdtfeger, Leo Zwell

The equilibrium between Ir-Fe or Rh-Fe alloys, iron oxide (wüstite or magnetite), and CO2-CO atmospheres has been determined at 1200°C. The data are used to derive the activities in these binary solid solutions. Both systems show negative deviations from Raoult's law. The lattice parameters are given for the investigated Ir-Fe and Rh-Fe alloys. IRIDIUM and iron form a continuous series of fcc solid solutions at elevated temperatures.' Rhodium-rich Rh- Fe alloys have fcc structure.' In the medium concentration range an ordered bcc phase is stable at temperatures up to about 1300°C. Phase relations in iron-rich alloys are not well-known. No thermody-namic data are available for these alloys. EXPERIMENTAL METHOD The experimental method used was to measure the equilibria between a gas phase of known CO2/C0 ratio, the alloy, and iron oxide (wüstite or magnetite). In one series of experiments the alloys of known composition were heated in CO 2-CO gas mixtures. After treatment (usually 1 day) the sample was quenched to room temperature and its surface examined visually to determine whether an oxide tarnish had formed. The procedure was repeated at slightly higher CO 2/CO ratios until the CO 2/CO ratio of incipient oxidation was found. Subsequently, the CO 2/C0 ratio was lowered again in small increments until the tarnish was reduced. In other experiments mixtures of alloy and iron oxide powders were pressed into pellets and equilibrated with the CO2-CO gas phase. In order to ensure that equilibrium was attained, two specimens with different starting iron content were heated side by side; in most cases, equilibrium was approached in one pellet by reduction of iron oxide and in the other pellet by oxidation of metallic iron. The sample was quenched to room temperature, and the composition of the equilibrated alloy was determined by X-ray measurements of lattice parameters and comparison of these values with calibration curves obtained from alloys of known composition. The oxides present in the specimens were identified by comparison of their diffraction patterns with those in the ASTM Card File. It may be expected from the noble character of iridium and rhodium that no appreciable amount of iridium or rhodium is dissolved in wiistite and magnetite under the present experimental conditions. The activity of iron in the alloy is then equal to that established in the iron oxide by the COrCO atmosphere. The activities of iron in wüstite and magnetite, as a function of oxygen pressure, were taken from the work of Darken and Gurry,

Jan 1, 1969

By L. D. Jaffe, D. C. Buffum

The importance of temper brittleness in alloy steels has long been realized in Europe. In the United States recognition of its importance has developed within the last several years. Many brittle failures encountered in parts made of alloy steel are undoubtedly attributable, wholly or in part, to temper brittleness. These failures have occurred particularly at low temperatures, under shock loading, and in the presence of notches, restraints and combined stresses. It has been almost universally accepted that plain carbon steels are not susceptible to temper brittleness. As a result, considerable effort has been expended in attempts to discover the manner in which alloying elements introduce temper brittleness. It is desired to raise the possibility that plain carbon steels are not only susceptible to temper brittleness, but are much more susceptible than alloy steels, in the sense that they embrittle much more rapidly. It is suggested that previous views, (that plain carbon steels are not susceptible), are based upon an erroneous interpretation of the experimental results. Interpretation of Previous Data For many years the standard criterion for susceptibility of a steel to temper brittleness consisted of comparison of the energy absorption, in a notched-bar impact test at room temperature, of specimens that had received two heat treatments.' One specimen (or group of specimens) was quenched, tempered, and quenched from the temper. The other specimen (or group) differed only in having received an embrittlement treatment, which might consist of a slow cool from the tempering temperature, or of an isothermal hold in the range 45w550°C subsequent to quenching from the temper. If the energy absorption of the specimen receiving the embrittlement treatment was lower than that of the specimen not given this treatment, it was said that the steel was susceptible to temper brittleness. If the energy absorptions were the same, it was said that the steel was not susceptible. Several investigators2J found that plain carbon steels showed negligible difference in energy absorption in such tests (at least when their manganese content was below 0.60 pct), and concluded that plain carbon steels are not susceptible to temper brittleness. Recently the deficiencies of the criterion mentioned above have been pointed out.'-= The criterion now generally used for susceptibility to temper brittleness retains the heat treatments used in the earlier scheme, but instead of the notched-bar impact tests being made only at room temperature, they are made over a range of temperatures, covering the transition from ductile to brittle fracture. If the transition temperature of the specimens receiving the embrittlement treatment is higher than those

Jan 1, 1949

By M. J. Greaves

All available data concerning risk as it applies to scaling up pyrometallurgical plants, processes, and equipment are determined to estimate the statistical chance of success. Random numbers are assigned to all data in order to avoid any chance of bias. The data bank is organized in such a way that an estimate can be made of the degrees of risk involved over a wide range of circumstances. Included are duplicating existing designs and large commercial installations based on smaller commercial installations, pilot models, or bench models.

Jan 1, 1977

State Mine Experiment Station, College of Engineering, University of Alabama, University, Ala Copies of two bulletins issued by the Mine Experiment Station may be had by writing to the Director of the School of Mmes at the above address: Bulletin 1, Coal losses in Alabama, 2, A specific gravity study of Alabama coals The Cooperative work of the Mine Experiment Station with the Southern Experiment Station of the U S Bureau of Mmes is covered by Bulletins of the U S Bureau of Mines

Jan 1, 1933

By Frank C. Greene

Drilling in Missouri in 1939 was marked by wildcatting in the northern half of the state. The total completions numbered 82, exactly half the 164 of 1938. There were 15 gas wells with an initial open flow of 6,383,150 cu. ft., 4 oil wells with about 40 bbl. initial production, and 63 dry holes. The wildcatting followed the widely publicized leasing activity in the Forrest City Basin in northwestern Missouri, northeastern Kansas, southeastern Nebraska and southwestern Iowa. It is worth noting that

Jan 1, 1940

By M. W. Bartley, Hugh M. Roberst

ERRATA In the paper (Mining Technology, January 1943) Page 19, second column. Line 5 should read: of Lower Huronian and Early Middle Huronian. Page 20, second column, line 17. Read magmatic solutions instead of magnetic solutions. In the discussion (Mining Technology, September 1943) On page 2 of this discussion pamphlet there is a typographic error. In the chemical analysis, the first reaction should read: CaCO3 + H2O = CaO2H2 + CO2 AMERICAN INSTITUTE OF MINING AND METALLURGICAL ENGINEERS

Jan 1, 1943

By Frank C. Greene

Drilling in Missouri in 1939 was marked by wildcatting in the northern half of the state. The total completions numbered 82, exactly half the 164 of 1938. There were 15 gas wells with an initial open flow of 6,383,150 cu. ft., 4 oil wells with about 40 bbl. initial production, and 63 dry holes. The wildcatting followed the widely publicized leasing activity in the Forrest City Basin in northwestern Missouri, northeastern Kansas, southeastern Nebraska and southwestern Iowa. It is worth noting that

Jan 1, 1940

By J. H. Rose

The arrangement of the reverberatory furnace and the two waste-heat boilers at the Magma Copper Company's smelter at Superior, Ariz., is shown in Fig. 1. The inside dimensions of the furnace at the slag line are: length, 96 ft.; width, 22 ft. The boilers are Erie City vertical type with a rated capacity of 700 hp. The 3-in. boiler tubes are arranged in two banks with a vertical baffle between. The banks are 30 tubes wide by 9 tubes deep—a total of 540 tubes.

Jan 1, 1934

For the third year in a row total value of the Nation's mineral production broke all previous records. A new peak of $20.4 billion was reached in 1964. So says the U. S. Bureau of Mines. The Bureau's preliminary estimate for 1964 is $800 million higher than the value reported for 1963, and $1.6 billion greater than the 1962 figure. The unprecedented demand for minerals, has stimulated development of new mines and expansion of processing capacity in many parts of the country.

Jan 2, 1965

It was a pleasure listening to this paper. Gary Works' problems were a lot more extensive than the trunnion bearing problems encountered at the Weirton Steel Division. In our two-vessel shop bearing failures are critical in that with a bearing failure on an operating vessel and the second vessel under rebuild, we are down until the vessel rebuild is completed or the bearing is repaired. The first bearing problem at Weirton occurred after we had been operating three years. The failure occurred during the 8th heat following "bum-in" of the vessel. Immediate steps were taken to change the damaged float bearing without an extensive search for the reason the bearing failed. Once the campaign was run out the bearings were inspected and found to be damaged. Field checks revealed that the bearing pedestals were not properly located and as a result the freedom of the float bearing was restricted. The trunnion pin end to end dimension had decreased due to distortion and deflection in the trunnion ring. These dimensions were within tolerances. The damage to our bearing was similar to that in the exhibits from U.S. Steel-Gary Works. Steps taken to correct what was found in the field checks were as follows: 1. The pedestals were relocated to center the bearings. 2. 4" diameter pins were installed to locate the housing in the pedestals. 3. The bearing pedestals were opened up to allow the bearing housing to move slightly in the pedestal. 4. Lubrication fittings for greasing between the bearing housing and the pedestal were installed.

Jan 1, 1972

By Zay Jeffries

THE metallic products of today represent the temporary end point of the efforts and interplay of thousands of years of the human struggle for existence, for pleasure, for conquest, for defense, for improvement in the standard of living, and for the satisfaction of that irrepressible urge to discover and utilize the materials and laws of nature Each metal has gained its place in the sun in severe competition with all other materials, be they metallic or nonmetallic Each serves better than any other for certain purposes. The compromise between cost and properties usually determines the selection of a metallic product for a given use. There are exceptions, as in wartime when the availability at a certain place at a certain time may far outweigh the ordinary economic considerations. In many instances superior properties are vastly more important than cost. If this were not so, the metal industry, for practical purposes, would be the iron industry. The use of 38,000,000 metric tons of newly produced nonferrous metal during, the five-year period from 1940 through 1944 is ample evidence that the special properties of these many metals have great economic value. In fact, our extensive industrial advances would have been quite impossible without the great range and variety of properties and combinations of properties of the nonferrous metals. This observation is not made to detract in the slightest way from the dominant role played by iron and steel. During the past century the production of pig iron has constituted well over 90 per

Jan 1, 1947

By L. S. Pratt

IN 1910 the author was engaged in a qualitative study of the radio-activity of several chemical substances and a few minerals. In the course of the work he studied the mineral allanite (obtained from granite ledges at Topsham, Maine), and found it to be appreciably radio-active. Recently the fact was brought to his attention that the radio-activity of allanite is not well known, although Hon. R. J. Strutt in 1905 published a list of radio-active minerals with their analyses, including allanite from Amherst County, Virginia. In the work done, a standard ,type of electroscope was used, and the readings were made with a telescope, fitted with a scale, by means of which the rate of discharge could be readily determined. The natural "leak" of the instrument was carefully determined, and all results corrected accordingly. The method of study was as follows: The material to be tested was finely powdered, and spread over the bottom of a small, inactive pan. The electroscope was then charged, and the pan placed in position. The door of the instrument was closed, and the rate. of discharge carefully determined. All results were reduced to common form to permit of comparison. It is to be noted that the materials tested were not used in strictly comparable quantities, such as if 1 g. of. each had been used, but about the same quantity of powder was used (in the cases of the solid substances), so that the results are qualitatively accurate.

Jan 5, 1916

AS we contemplate the bestowal of the John Fritz medal year after year on men of wide-world dis-tinction in the various fields of engineering, men who in one way or another have given impulse and direction to the progress of mankind, the question becomes inter-esting as to what manner of man was John Fritz and what were the qualities that singled out his name to be so conspicuously associated with the world's great scientific and industrial achievements. If, as Lowell said, it is the duty of the nation to pro-duce great men, our country surely rose to her oppor-tunity when she guided and guarded the career of John Fritz. Starting life as a blacksmith with no advantages of education, without influential friends or the favor-ing accidents of fortune, he advanced steadily in use-fulness, power and respect of his fellowmen until by common consent he occupied the first place in the domain of the steel industry of this, country. The numerous honorary scientific memberships conferred upon him in this country and abroad attest the esteem in which he is held by his fellow engineers. Twenty years after his retirement from active business at the age of seventy, he lived to enjoy, as few men have been permitted to do, the fame and the friendships which he had so amply earned. His sterner qualities of industry, integrity and sterling character were re-lieved by unfailing human sympathy, humor and spon-taneous good-will toward his fellowmen. To all who

Jan 3, 1928

The Hurghada field is still the major producing field in Egypt. There was almost no activity in the Abu Durba field during 1936 and no new evidence is available. The following table summarizes the information on the Hurghada field for the year 1936. Hurghada Field Age of field to end of 1936, years.................... 23 Producing area for gas and oil, acres................. 1,050 Barbels Total oil production to end of 1936.................. 29,046,572 Total oil production during 1935.................... 1,212,182 Total oil production during 1936.................... 1,218,708 Daily average during November, 1936............... 3,249 MillionB CU. Ft. Total gas production (Aug. 1925 to end of 1936)...... 3,966 Total gas production during 1935................... 278 Total gas production during 1936................... 280 Maximum daily in 1936............................ 0.9 Number of producing wells completed to end of 1936... 94 Number of producing wells completed during 1936. ... 3 Number of wells abandoned during 1936............. 3 Producing wells at end of 1936...................... 768 Average depth of bottom of producing wells, ft....... 1,720 Average depth of top of producing horizon, ft......... 1,598 Character of oil, approx. average during 1936: Gravity at 60' F., 0.900; base mixed. Character of gas, approx. average during 1936: gallons gasoline per 1,000 CU. ft., 6.2. Producing rock (main): Nubian sands, Cretaceous; character, sand rock and sandy shales. 1 The figures given by the author were in tons. A conversion factor of 6.98. based on 0.900 sp. gr., was used to obtain the number of barrels.—Ed. 2 All pumping.

Jan 1, 1937

By Edward A. Vitunac

The emerging importance of pneumatic conveying systems for bulk materials is largely due to the economic advantages such systems frequently exhibit when compared to alternate methods. Included in these advantages are relative simplicity, ease of installation, flexibility, ease of maintenance, cleanliness, safety and ease of automation to the degree desired. In general, installed costs favor a pneumatic system when compared to competing mechanical systems if the transporting distances are long or to and from many points. In addition, supplemental use such as cooling, heating, or drying may supply the incremental value required to justify its selection.1 The main disadvantages of a pneumatic system are the greater horsepower required per unit weight of material conveyed, material limits in abrasiveness, and density. In addition, material breakage tends to increase at changes of direction and at any obstruction such as that caused by the imperfect butting of two pipe sections in the conveying line. Classification of the material at the discharge may also cause problems in dusting and segregation. Materials weighing less than 4 lb per cu ft tend to cause feeding and collecting problems although they can be conveyed easily. Material between 4 lb and 20 lb per cu ft can be handled with fewer problems, but flow rate is hard to predict. The 20-60 lb per cu ft range offers best results, whereas materials of over 60 Ib per cu ft tend to drop out of the air stream and settle in the pipeline unless careful pro- visions are made to prevent this.2

Jan 5, 1968

By Tracy Jarrett

In 14-karat gold alloys, as in 10-karat gold alloys,3 the addition of such metals as zinc, nickel, copper and silver produces a wide range of physical and chemical proper-ties such as color, hardness, corrosion resist-ance and melting points. These important factors made gold alloys desirable in the optical work and for jewelry. In 14-karat gold alloys, as well as in 10-karat or 12-karat, it is possible to have two golds of the same color, one of which will corrode more than the other, although it may be harder. Some of these alloys have been investigated by F. E. Carter,1 E. M. Wise,5 and L. Sterner Rainer.4 In this group of alloys the gold content of 58.3 per cent (14-karat) was held constant, while the copper varied from 36 to 24 per cent. The balance of the alloy consisted of one, two, or three of the metals silver, zinc, and nickel. All the alloys were melted in an induction furnace and cast into an ingot that meas-ured 3 by 1/4 by 3/4 in. The method of determining the melting points, color deter-minations and acid test have been discussed in previous papers by the author.2,3 It is necessary to use small test bars (Fig. r). The tensile bars were annealed at 1300°F. for 20 min. and then air-cooled. There being a very marked drop when the yield point was reached, "the drop of the beam" method was used in determining the yield point.

Jan 1, 1940

By Harry Seltz

INTERMETALLIC compounds are formed in many binary metal systems. Some compounds are stable to their melting points, and others decompose at lower transition temperatures. Even those of the first class are dis-sociated in the liquid state, as indicated by the continuous for in of their solubility curves at their melting points1. While the lattice structures of some of these compounds have been determined, their thermodynamic properties have not been investigated. In this paper is described the determination of the free energy and heat of formation of the compound CdSb, which is of the first class mentioned above, melting congruently at 455° C. This compound shows a rhombic structure, and the lengths of the edges of the elementary cell containing four molecules are: a =6.52, b = 8.60, c = 4.16 A.2 There are three possible methods of determining the free energy of formation of a compound of this type. The first method, applying the third law of thermodynamics, requires the measurement of its heat capacity preferably to liquid hydrogen temperatures, and a calorimetric determination of its heat of formation. The second method involves the study of the equilibrium of the compound in some gas reaction, such as: CdSb + CO2 = CdO + CO + Sb From the known free energies of formation of CdO, CO2 and CO the free energy of formation of CdSb could be calculated. The third method measures the electromotive force of a galvanic cell in which the cell

Jan 1, 1935

By Kenzo Murao, Sei Nakao

HISTORY OF ASHIO SMELTER The Ashio copper mine, which formed the main part of Furukawa mining industry, is located inland of Kanto area, and is known as the oldest copper mine of Japan. The mining started even since 1610, and Mr. Furukawa began management in 1877. Afterwards, within a short period, the mine became to have the highest productivity in the Far East. The total quantity of mined copper reached approximately more than 800 thousand tons. The mother rock of the ore deposit in Ashio was rhyolite, and was formed of sissurefulling and irregular clod that was called Kajika deposit. The lode was nzrrow of 6 to 7cm. The mineral was formed mainly of chalcopyrite, including also pyrite, pyrrhotite, and arsenopyrite that were not favorable. After the founding of the copper mine, the Ashio smelter started the operation of Mabuki process as the beginning in 1611, and subsequently adopted the processes of the blast furnace, reverberatory furnace, and flash smelting furnace of the present use. As indicated above, the copper ore of Ashio mine included arsenic. For the purpose to remove it, the operation of the arsenic trioxide production using MacDougall's multiple hearth roaster was started in 1918, and it maintained the status of having the most qualified technique within the country. However, as the completeness in the disposition of anti-pollution and safety had been requested in those years, we studied and developed a unique equipment in 1970. It excludes the heavy metals especially arsenic and copper from the waste water of sulfuric acid process of Flash Smelter's exhaust gas.

Jan 1, 1976

By William P. Blake

The magnetic iron ores of the Rees & Wilder tract, Unaka Mountains, East Tennessee, and North Carolina, so far as examined by me, are peculiar in containing considerable quantities of the mineral zircon in dark red-brown crystals, ranging in size from one-tenth of an inch, or less, to five-tenths of an inch in length. As zircons are decomposed by fusion with alkalies, the constituents may exert some favorable influence upon the iron product, which is generally acknowledged to be of superior quality. New Haven, April 20th, 1878.

Jan 1, 1879