Search Documents

By H. E. Nold

High-volatile coals are most desirable for kiln firing. Low-volatile and even anthracite coals can be used successfully. Most periodic kilns use coal and are hand fired. A few stoker installations have been economically successful. Continuous tunnel kilns reduce fuel consumption 40 to 55 per cent. They are rapidly replacing periodic kilns in the manufacture of the finer wares. They have found great favor in the refractory industry and are successfully used in firing almost all kinds of heavy clay products. Fuel oil has found rather wide application in the Southwest and West. Natural gas is a satisfactory fuel for kiln firing. It is the principal competitor of coal and has largely replaced it for firing the finer wares but cannot compete with it in firing heavy clay products except in regions where cheap gas is available. Figures are given showing the relative thermal efficiency of coal and natural gas as used for firing ceramic ware. The ceramic industry uses from 12,000,000 to 12,500,-000 tons of coal per normal year. The principal use of coal is in firing the heavy clay products. This potential market amounts to about 9,250,000 tons per year. Coal producers could increase sales by furnishing expert firing instruction.

Jan 1, 1934

In a letter to Prof. L. P. Breckenridge, chairman, urging the continua-tion of the Fuel Conservation Committee of the Engineering Council, Edwin Ludlow calls attention to the millions of tons of culm in the an-thracite region that can be utilized in properly equipped plants and the electricity generated transmitted to. New York, Philadelphia, and other nearby cities. He says: "Experiments have shown the economic value of No. 4 Buckwheat, which passes through a 1/16-in. mesh and over a 1/32-in. mesh. Culm passing through a 1/32-in- mesh is pulverized until it passes through a 300 mesh and is then burned under boilers. Two plants of this kind are now in successful operation in the anthracite region. Another rather interesting experiment was using 30 per cent. of this pulverized coal with 70 per cent. of oil in the generation of steam in the place of pure oil. This utilization of the fine anthracite, which has always been a waste product and thrown away, is not only fuel conservation in its truest sense but in the case of a bituminous strike, when no strike is contemplated in the anthracite field, will furnish fuel to manufacturing plants that otherwise would be obliged to shut down."

Jan 12, 1919

That the chemical industries are alive to the situation that they now occupy in the sum of affairs is evident in the preparations being made by many firms for the Second National Exposition of Chemical Industries To be-held at the Grand Central Palace, New York City, during the week of September 25-30, 191 The list of exhibitors indicates that the Exposition is already twice the size of its successful predecessor. The American Chemical Society will hold its annual meeting during the whole week, the American Electrochemical Society has arranged to - hold its meetings on September 28, 29 and 30, and the Technical Association of the American Pulp and Paper Industry is also planning to meet during the week. The Bureau of Commercial Economics at Washington is again co- operating with the Exposition by arranging an elaborate program of motion pictures covering subjects dealing with the industries depending on chemistry. Many of these films will have their first showing at the Exposition. They will take the visitor through industrial plants, shops, manufactories, mines, etc., where visitors are never admitted; they will show operations that in ordinary light would never be seen; they will demonstrate more than any other kind of motion picture the great strides and improvement in the art of photography.

Jan 8, 1916

E. D. TILLYER,* Southbridge, Mass. (written discussion?).-It is quite generally known that there is very little that is standard about a mercurial thermometer at temperatures above 212° F. (100° C.) because so many precautions must be taken-precautions that are rarely realized in practice-such as depth of immersion, aging, elastic fatigue, separation of mercury column, and accidental deformation from very slight excess temperature. One cannot help wishing that Mr. Brown would dwell at greater length on the practical side of both radiation and optical pyrometey, both of which have great possibilities as commercial instruments. In the radiation pyrometer we have ideal conditions for a permanent instru-ment, no materials being exposed to excessive temperatures or subjected to contamination from the furnace fumes which may raise such havoc with an ordinary pyrometer. The development of a radiation pyrometer requires a thermocouple having a relatively high electromotive force but which need stand temperatures of only 200° F. or 300° F. instead of 1500 to 2000° F., which is required of even a base-metal couple. The galva-nometer, if located near the thermocouple, does not need to have a high resistance as at such low temperatures no changes can occur in the thermocouple that will affect its resistance and, consequently, the in-dicated temperature.

Jan 11, 1919

By A. F. Taggart

OLIVER C. RALSTON, Salt Lake City, Utah (communication to, the Secretary*).-This paper has appealed to me as being one of the most lucid, well-connected and complete papers on this subject which has been published. To be sure, the concepts called upon in an explanation of the flotation process by these authors are mostly old ones which have been more or less discussed in previous literature, but they have nevertheless been assembled in a most constructive and suggestive manner. We find a new contribution to flotation theory in the effect of fine particles increasing the viscosity of the interfacial film between a liquid and a gas. This phenomenon has been variously hinted at but never definitely stated in accepted scientific terms. The discussion of "contact angles". is very clear and will doubtless be welcomed by those who have not had the opportunity to investigate the literature on this subject, but it is unfortunate that the "hysteresis of the contact angle," observed by Sulman and reported some years ago, is not mentioned or explained. A few other points need discussion in order to call attention to the fact that, while this paper is the best discussion of the subject which has yet appeared, all of the truth has not yet been told.

Jan 12, 1916

High-type research metallurgist with approximately following qualifications: American, 30 to 45 years old. Mind-Analytical. Education-college graduate. Practical shop experience-not less than 5 years. Metallurgical experience in steel making-at least 5 years. Chemical experience-should have some chemical training. Research ability -should be the type of man who is interested in new developments or research work. No. 337. Engineer with some underground, experience who is physically able to spend a large portion of his time underground, to act as general efficiency engineer. He will have cost keeping on special work, charge of contracts, labor distribution, etc. No. 338. The services of a man experienced in flotation and familiar with the Callow apparatus are required for a short engagement in South America. No. 339. A position as surveyor and draftsman for mines in Mexico is open. Opportunity for advancement. Climate pleasant and healthful. Knowledge of Spanish required. No. 340. The Bureau of Construction and Repair, Navy Department, Washington; D. C., is in need of a few draftsmen of experience for work in connection with the development of industrial yards and shops of the Navy, under the cognizance of the Shore Establishment Division of the Bureau of Construction and Repair. Training in one of the following courses would be considered a requisite qualification:

Jan 9, 1918

By B. R. Palmer, G. Gutierrez B., M. C. Fuerstenau

Selective flotation in nonmetallic systems is often complicated by the presence of iron-bearing silicates occurring as gangue. Minerals such as augite, diopside, hornblende, and tourmaline respond readily to flotation under the same conditions as ore minerals. Mechanisms by which these minerals respond to flotation with anionic collectors must be established if selective separations are to be made in these systems. It was the objective of this investigation to determine the mechanisms involved in the flotation of two pyroxenes, augite and diopside, with potassium oleate. Experimental Materials and Methods Pure potassium oleate, prepared by neutralization of oleic acid with KOH, was used as collector, while reagent-grade HC1 or KOH were used for pH adjustment. Conductivity water, made by passing distilled water through a mixed-bed ion exchange column, was used in this investigation. Two pyroxenes, [ ], were involved in this work. One member of this class of minerals was augite and was found to contain 3.3% calcium, 4.6% iron, and 9.6% magnesium. The source of this mineral was Tillamook County, Ore. The other pyroxene involved was diopside which contained 8.3% calcium, 2.7% iron, and 7.6% magnesium. The source of this sample was Bancroft, Ont. Microflotation experiments were conducted with a Hallimond cell. Mineral samples were ground dry and sized to 100 x 200 mesh. One-gram charges were conditioned for 3 min in the presence of various additions of potassium oleate. Flotation was conducted for 1 min with a nitrogen flow rate of 50 cm3/min. The electrophoretic mobilities of these two minerals were measured with a Zeta Meter in the absence and presence of [ ] salts and in the presence of an indifferent electrolyte, NaC1, added to maintain ionic

Jan 1, 1978

By John Pew

PRIOR to the development of the bulk-oil carrier, practically all transportation of oil was in barrels and in cans contained in wooden cases; the latter was known as case oil. In the year 1885, approximately two hundred million gallons of petroleum were exported from this country in barrels and about one and three-quarter millions in bulk; less than twelve years later, the shipment in barrels had decreased to nearly one and three-quarter million gallons, while the transport of bulk oil had increased to four hundred eighty-four million gallons. The first modern tanker, the "Glückauf," was built in England in 1886. Her hull, which was 300 ft. long, was divided into compartments by transverse bulk-heads, these compartments being divided by longitu-dinal center-line bulkheads extending throughout the oil spaces. There was a pump room forward of the boiler room, thus providing a cofferdam or safety space. Between the main and upper decks, a narrow trunk extended the full length of the' oil spaces, the trans-verse and longitudinal bulkheads being carried to the upper deck. This allowed for the expansion of the oil from a rise in temperature, and if the tank below the main deck was kept full, the danger of the oil moving with the roll and pitch of the vessel was considerably reduced. Spaces for the carriage of light oil were provided on each side of the vessel outboard of the expansion trunk, while water ballast was carried under the machinery compartments fore and aft. Although vessels previously had been built to carry oil next to the skin of the ship, it is claimed that the "Glückauf" was the first one constructed on the new principle outlined.

Jan 12, 1922

By Walter Miller

The focus of attention during 1939 was on increasing the octane number of gasoline. The "octane race" resumed full swing. The averagc octane number of house-brand gasoline by the end of the year had easily reached two numbers higher, with several companies in the field actually purveying house-brand gasoline of 78-80 "research" octane number, equivalent roughly to from 74 to 77 A.S.T.M. octane rating, compared with the 70 A.S.T.M. ceiling of two or more years ago. Whether this trend toward much higher octanes is the result or the cause of the many t,echnical developments in the motor-fuel field of recent, years, progress has really been startling. In addition to the advance in catalytic cracking and catalytic re-forming, other important contributions to the technical ability to produce higher octane values include: installat>ions involving increased capacity in thermal re-forming, with improved economic status both as to yields and octane number, by coupling with catalytic polymerization; more widespread adoption of catalytic and thermal polymerization, and a surge toward extensive installations of newly developed alkylation processes for making iso-octane, neo-hexanr and other high antiknock products; and greater use of improved desul-phurization processes, and application of superfractionation methods for segregation of practically pure hydrocarbons with superior octanr qualities from gas and highly volatilc liquids. The approaching of practical limits in the use. of tetracthyl lead (t,hr well-known "law of diminishing returnsn coming into the picture at the higher octane levels being approached) has given impetus to development of the methods listed above. In particular, processes that improve the octane rating and also increase ethyl lcad sc.nsitivity have had considerable study durirlg the year. CatSlytic Re-foRming Although the interesting report on the Houdry catalytic cracking process presented at the annual meeting of the American Petroleum

Jan 1, 1940

By Walter Miller

The focus of attention during 1939 was on increasing the octane number of gasoline. The "octane race" resumed full swing. The averagc octane number of house-brand gasoline by the end of the year had easily reached two numbers higher, with several companies in the field actually purveying house-brand gasoline of 78-80 "research" octane number, equivalent roughly to from 74 to 77 A.S.T.M. octane rating, compared with the 70 A.S.T.M. ceiling of two or more years ago. Whether this trend toward much higher octanes is the result or the cause of the many t,echnical developments in the motor-fuel field of recent, years, progress has really been startling. In addition to the advance in catalytic cracking and catalytic re-forming, other important contributions to the technical ability to produce higher octane values include: installat>ions involving increased capacity in thermal re-forming, with improved economic status both as to yields and octane number, by coupling with catalytic polymerization; more widespread adoption of catalytic and thermal polymerization, and a surge toward extensive installations of newly developed alkylation processes for making iso-octane, neo-hexanr and other high antiknock products; and greater use of improved desul-phurization processes, and application of superfractionation methods for segregation of practically pure hydrocarbons with superior octanr qualities from gas and highly volatilc liquids. The approaching of practical limits in the use. of tetracthyl lead (t,hr well-known "law of diminishing returnsn coming into the picture at the higher octane levels being approached) has given impetus to development of the methods listed above. In particular, processes that improve the octane rating and also increase ethyl lcad sc.nsitivity have had considerable study durirlg the year. CatSlytic Re-foRming Although the interesting report on the Houdry catalytic cracking process presented at the annual meeting of the American Petroleum

Jan 1, 1940

By O. G. Bell

Development and exploratory work continued vigorously during 1933 in Southwest Texas and, from a standpoint of new production discovered, the new discoveries probably equal or may even exceed any previous year in the history of this area. While exploratory work has been general over the area much of it has been confined to two localities; namely, northern Duval-southern McMullen counties and Starr County. A persistent effort has been made to open new productive areas in northern Duval County and the adjacent part of McMullen County, occasioned primarily by the fact that the Government Wells group of fields in northern Duval County have been by far the best fields so far developed in this part of the state, and the possibility of being able to find new fields in the same general area under similar geologic conditions. This has resulted in the discovery of three new fields, Northwest Government Wells, Moca and Eagle Hill. In addition encouraging shows have been found in North Kohler, Hoffman, Smith-Hunter and the Ignacio areas with the prospect that continued exploratory work will develop some of these prospects into fields. Wildcatting in Starr County was the continued result of an effort to find a trend of production through the county southwestward from the older Reynosa Escarpment fields in Webb, Jim Hogg and Zapata counties. This same impulse has caused most of the wildcatting in Zapata County. New Fields Cuevitas.—During the early part of the year the Sun Oil Co. began some core-drill work on a block of leases in northern Starr County, then in June drilled a test which found production in the McElroy member of the Jackson at 2200 ft. Drilling in this field has continued but the productive area has not as yet been clearly defined. Seven oil wells and three gas wells have been completed. There is as yet no pipe line outlet for this production, hence no productive history of the wells has been

Jan 1, 1934

By A. H. Taitt

The original basis for the search for oil in Great Britain was described last year.t During 1937 the exploratory drilling by the D'Arcy Exploration Company, Ltd. has been continued. Three wells have been completed in the south of England and a fourth is nearing completion. In addition, test wells are now being drilled in Scotland and East Yorkshire. Southern England The test well on the Portsdown structure, which at the end of 1936 was drilling in the Lower Lias at 5792 ft., entered the Triassic at 6540 ft. and was completed in that formation at a depth of 6556 ft., without encountering further indications of petroleum. The Henfield well encountered the Lias at a depth of approximately 4090 ft., and after drilling 800 ft. of an argillaceous development of that formation entered a series of marls, breccias and conglomeratic limestones of the Carboniferous. Drilling was suspended at a depth of 5105 ft., in the latter formation. The consistently impermeable nature of the strata encountered in the Portsdown and Henfield test wells focused attention on the desirability of obtaining shore-line conditions of the Jurassic. With this end in view the Kingsclere anticline, a few miles south of Newbury in Berkshire, was selected for a next test. The Kingsclere well has now reached a depth of 5032 ft. in the Lower Lias and has encountered a full development of the Jurassic. With the exception of the Portland sand, which has a slightly greater porosity, and the Corallian, in which relatively great thicknesses of impervious limestone were met, conditions of sedimentation have been found to be comparable with those of the earlier wells. Small traces of petroleum have been found in cuttings and cores, but formation tests carried out at frequent intervals have yielded no flow of oil. In order to test the Corallian, from which series an outcropping oil sand had been found, a test well was drilled in a near-by anticline at Poxwell in Dorset. The Poxwell well started in the Portland beds and entered the Corallian at 995 ft. The sands at the horizon of the out-

Jan 1, 1938

AT THE beginning of February the British Government announced acceptance of the American terms for funding the war debt, the main features-being as follows: Interest rate of 3 per cent. for the first 10 years and then 3 ½ per cent. up to the final extinguishment of the debt at the end of 62 years. The interest from the time since the loans were made to the actual beginning of the funding arrangement to be recomputed at 4 1/4 per cent. instead of the 5 per cent. rate now in effect. Congress ratified the contract respecting the British debt. The ship subsidy bill was relegated to the rear, which is indeed an end to the project. The natural consequence of this will be a liquidation of the Govern-ment's shipping business. The joint committee on the reorganization of Govern-ment departments made its report to the President. In general this seems to offer a well-considered plan for the coordination of Government service. The pro-posals respecting the bureaus that are particularly associated with the mining industry may be subject to criticism. According to the committee's plan, the Geological Survey remains in the Department of the Interior, but the Bureau of Mines and the compilation of the statistics of mineral production are transferred to the Department of Commerce. The Lausanne conference among the European powers came to an end early in February, without any treaty having been signed, owing to the refusal of the Turks to accept the ultimatum of the Allies. Theoreti-cally this left conditions in a state-of war between the Allies and Turkey. However, no actual movements have resulted. The French and Belgians continued to hold the Ruhr district of Westphalia, extending their lines and administration of the region. The Germans adhered to the policy of passive resistance. In the Parliament of Great Britain the French and Belgian policy was plainly declared to be unwise and dangerous. French and Belgian industries, moreover, were troubled by strikes among their own coal miners for higher wages. The Poles and Lithuanians engaged in border war-fare;. the civil war in Ireland continued. The rest of the world was quiet insofar as military operations are concerned.

Jan 2, 1923

By Roscoe C. Clark

In October 1945. R. F. Farris. in an AIME paper entitled Method For Drtermining Minimum Waiting OIL Cenzent Time, presented a method for caiculating the minimum WOC* time required in oil well cementing operations. Briefly. this method consisted of shutting in a well. after the cement had been placed and noting the time required fur the wellhead pressure to reach a. maximum. This time was then multiplied by a factor of 1.5 to determine when the cement had reached sufficient strength to support the weight of the casing. As a result of this work, a number of areas have reduced their WOC time ~Wuirements with the subsequent saving of considerable rig time. The tests conducted by Farris were, for the most part, conducted under cementing temperatures in excess of 70°F. This was done because in the overwhelming majority of cases. cementing temperatures are in excess of 70°F (only in tile northern part of the country. primarily in the Rocky Mountain ares. in cementing surface casing are temperatures below 70° F. encountered, and such temperatures occur only during the winter months). The Stano-lind Research Laboratory since that time has performed a number of tests both in the laboratory and in the field to evaluate this WOC factor when cemeriting temperatures are lower than 70°F. The results of these tests indicated the need for greater WOC time in areas affeaed by abnormally low cementing temperatures. These tests indi.cated that a woc factor of 2 (Time from start to mix cement to maximum wellhead pressure x 2 = Time to drill plug) will allow sufficient time for the cement to develop adequate strength. A field test under abnormally low cementing temperatures (surface temyerature 35°F., mud discharge temperature <70°F. and cementing depth 500 ft.) in the Rangely Field, "* using the WOC factor of 2, indicated the time to drill the plug as 45 hours. Well conditions preventing getting back into the well until a 48-hour WOC time had elapsed. At this time, the plug drilled firm to hard indicating that the cement had reached its final set. It is contemplated that during next winter additional field tests will be performed to further check the results of the laboratory and field tests conducted to date,

Jan 1, 1949

By Roscoe C. Clark

In October 1945. R. F. Farris. in an AIME paper entitled Method For Drtermining Minimum Waiting OIL Cenzent Time, presented a method for caiculating the minimum WOC* time required in oil well cementing operations. Briefly. this method consisted of shutting in a well. after the cement had been placed and noting the time required fur the wellhead pressure to reach a. maximum. This time was then multiplied by a factor of 1.5 to determine when the cement had reached sufficient strength to support the weight of the casing. As a result of this work, a number of areas have reduced their WOC time ~Wuirements with the subsequent saving of considerable rig time. The tests conducted by Farris were, for the most part, conducted under cementing temperatures in excess of 70°F. This was done because in the overwhelming majority of cases. cementing temperatures are in excess of 70°F (only in tile northern part of the country. primarily in the Rocky Mountain ares. in cementing surface casing are temperatures below 70° F. encountered, and such temperatures occur only during the winter months). The Stano-lind Research Laboratory since that time has performed a number of tests both in the laboratory and in the field to evaluate this WOC factor when cemeriting temperatures are lower than 70°F. The results of these tests indicated the need for greater WOC time in areas affeaed by abnormally low cementing temperatures. These tests indi.cated that a woc factor of 2 (Time from start to mix cement to maximum wellhead pressure x 2 = Time to drill plug) will allow sufficient time for the cement to develop adequate strength. A field test under abnormally low cementing temperatures (surface temyerature 35°F., mud discharge temperature <70°F. and cementing depth 500 ft.) in the Rangely Field, "* using the WOC factor of 2, indicated the time to drill the plug as 45 hours. Well conditions preventing getting back into the well until a 48-hour WOC time had elapsed. At this time, the plug drilled firm to hard indicating that the cement had reached its final set. It is contemplated that during next winter additional field tests will be performed to further check the results of the laboratory and field tests conducted to date,

Jan 1, 1949

The National Research Council was organized in 1916 at the request of the President by the National Academy of Sciences, under its congressional charter, as a measure of national preparedness. The work accomplished by the council in organizing research and in securing cooperation of military and civilian agencies in the solution of military problems demonstrates its capacity for larger service. The National Academy of Sciences is therefore requested to perpetuate the National Research Council, the duties of which shall he as follows: 1. In general, to stimulate research in the mathematical, physical, and biological sciences, and in the application of these sciences to engineering, agriculture, medicine, and other useful arts, with the object of increasing knowledge, of strengthening the national defense, and of contributing in other ways to the public welfare. 2. To survey the larger possibilities of science, to formulate comprehensive projects of research, and to develop effective means of utilizing the scientific and technical resources of the country for dealing with these projects. 3. To promote cooperation in research, at horse and abroad, in order to secure concentration of effort, minimize duplication, and stimulate progress; but in all cooperative undertakings to give encouragement to individual initiative as fundamentally important to the advancement of science. 4. To serve as a means of bringing American and foreign investigators into active cooperation with the scientific and technical services of the War and Navy Departments and with those of the civil branches of the Government. 5. To direct the attention of scientific and technical investigators to the present importance of military and industrial problems in connection with the war, and to aid in the solution of these problems by organizing specific researches. 6. To gather and collate scientific and technical information, at home and abroad, in cooperation with governmental and other agencies, and to render such information available to duly accredited persons. Effective prosecution of the council&apos;s work requires the cordial collaboration of the scientific and technical branches of the Government, both military and civil. To this end representatives of the Government, upon the nomination of the National Academy of Sciences, will he designated by the President as members of the council, as heretofore, and the heads of the departments immediately concerned will continue to cooperate in every way that may be required. THE WHITE HOUSE, WOODROW WILSON. 11 May, 1918.

Jan 7, 1918

By M. E. Straumanis, S. M. Riad

The lattice parameter of 99.999 pct pure Ag rtlas redetevnzined and found to be az5 = 4.08626 5 0.000041 with the vefnzctiotz correction included); the expatzsion coejjicient between 10° and 65°C was 18.73 X10-6°C-1. The lattice paratneter increased upon solution indium in silver in good agrement with other authors. The solid-solubility limit around room temperature was at 20.4 wt pct of in, which suggests that the high-temperature solubility (at about 689°C) determined by other authors is too low. The expansion coejficient of si1ver increases with the itzcrease of indium content between 10° and 65° C from, 18.73 (In = 0) to 20.9 x 10-6°C-1 (In = 20.4 pct), being only very slightly influenced by small amounts of indium. The expansion coefficents of all solid solutions increarsed strongly with temperature, reaching values > 27 x 10- 6 800°C. ACCORDING to the Ag-In diagram,&apos; the solubility of indium in silver (the a phase) extends to about 18 pct by weight at room temperature. However, there has been only one investigation of the solubility limit by X-ray methods—that of Weibke and Eggers.2 Hume-Rothery, Lewin, and Reynolds measured only the lattice parameters of Ag-In solid solutions3 as did Owen and Roberts4 and Adler and Wagner.&apos; The thermal expansivity of four solid solutions was determined by Owen and Roberts4 in a temperature range between 25" and 300°C. In view of the limited amount of work on Ag-In solid solutions, it seemed appropriate to redeter-mine the lattice parameters and the room-temperature solid-solubility limit, to find the exact expansion coefficients of the solid solutions at about room temperature (between 10° and 60°C) and the expansivity up to 800°C, and finally to derive the thermal-expansion coefficients for any alloy within the solid-solubility region. THE ALLOYS AND THE DETERMINATION OF LATTICE CONSTANTS The metals used were 99.9991 pet pure, supplied by the ASARCO company. Both silver and indium were weighed accurately on an analytical balance in

Jan 1, 1965

By H. J. Stehli

Probably the earliest sinter from lead ore was made in the product sinter boxes attached to some hand reverberatory roasters. The ore was drawn from the roaster bed when dead roasted, and then by laborious effort fritted together by rabbling at a high temperature in the sinter box. This was not a true sinter, but was a great improvement over the dusty dead-roasted fine ores. The Huntington-Heberlein pots were the first real advance in the art, and produced some real sinter. They required that the sulphides be preroasted to 5 or 6 per cent sulphur, and the long cycle of operating and deep bed of material used in the pots fostered the formation of densely fused material and fines. This necessitated crushing of the densely fused cake and returning to the next charge large amounts of fines screened out. The Huntington-Heberlein pots made comparatively high lead losses because the deep bed and high internal temperature together favored the volatilization of lead. Lime (CaO) was added to the charges, and this addition constituted the patented feature of the Huntington-Heberlein process. Its sole function we now know was to act as an isolator of the sulphide particles, and any other substance—for instance, iron oxide—of equal fineness performed the same function. The Savelsberg process used limestone instead of burned lime, and in this there was a definite advantage. The converting of CaCO3, to CaO is a highly endothermic reaction, so the lime acted not only as an isolator of sulphide particles but absorbed excess heat and to some extent prevented premature fusion of the sulphides. The Carmichael-Bradford process used gypsum instead of limestone, and had the disadvantage of adding more sulphur to a charge from which it was desired to eliminate sulphur. Here again the gypsum served only as an infusible isolator of sulphide particles. The first Dwight-Lloyd apparatus to sinter lead ores commercially was installed at Perth Amboy in 1907. The fact that lime in any form was necessary to sintering was quickly disproved by making excellent sinter from Bunker Hill and Sullivan table concentrates, silica sand and iron oxide only.

Jan 1, 1937

By Valentin Garfias

ALTHOUGH Mexico still ranks second in importance as produce for petroleum, the output in 1924 was 7 ½ per cent. less than in 1923 and 30 per cent. less than the peak production of 1921. The decrease may be partly accounted for by labor troubles and revolutionary activities early in the year, although undoubtedly the main factor was the continuous rise of the salt-water level in the South Fields, causing a decline of 24,000,000 bbl. in the production of light oil. Since the middle of 1923, the production of heavy crude has been greater than that of the lighter grade and, in 1924, the output of heavy crude was 2 ½ times that-of the light oil. DEVELOPMENT Drilling operations in the Mexican fields were probably more active in 1924 than in any other year, the greatest activity taking place in the Cacalilao and neighboring fields; toward the end of the year there was an added number of wells drilling in wildcat areas. The number of wells drilled in proved territory was almost twice that of the previous year, the increase taking place in the heavy-oil fields north of Panuco, as only 78 of the 710 wells completed were drilled in the Southern Fields. The percentage of successful completions decreased from 45 per cent., during 1923, to about 38 per cent., during 1924; there was also a noticeable decrease in the average flush production of the new wells. It is interesting to note that notwithstanding the increased drilling activity, the total production declined over 10,000,000 barrels. In the heavy-oil district, 632 wells were completed but only 231, or 36 ½ per cent., were commercially productive. The develop-ment in the Cacalilao area reached its peak in April and May, or about the time the first serious salt-water encroachments took place. Development in the old Panuco and Topila fields was more active than during the previous year, although the salt-water level continued to rise, the high price of crude making such development advisable especially for companies having to protect large-investments.

Jan 3, 1925

By H. W. Imholz

Active interest in the North Central Texas area centered in the development of the Palo Pinto limestone-producing zone, near the town of Avoca, in the northeast part of Jones County. This producing horizon was discovered in 1937, in the Iron Mountain Oil Company&apos;s well No. 1 Olander, in sec. 196, B.B.B. & C. survey, at 3238 to 3250 ft. During the development of this pool, it was generally referred to as the Avoca pool. As a second pool has been discovered in the same producing zone, also near the town of Avoca, the writer has taken the liberty of changing the name of the original Avoca pool to Avoca-Olander pool. Forty producers had been drilled in the Avoca-Olander pool by the end of 1938; their initial ranged from 28 to 300 bbl. per hour. Stimulus was given to the interest in the development of the Palo Pinto limestone when the Ungren-Frazier No. 1 Griffin, in sec. 199, B.B.B. & C. survey, Jones County, found the limestone from 3225 to 3250 ft., with an initial production of 931 bbl. per day. (This new pool has been given the name of Avoca-Griffin pool, by the writer.) The best well to be completed, up to the present time, is the Bert Fields No. 1 Taylor in sec. 199, B.B.B. & C. survey, which had an initial production of 748 bbl. in 3 hours. The Owen-Snebold No. 1 McKeever in sec. 158, B.B.B. & C. survey, in northwest Shackelford County, added to the interest in the Palo Pinto limestone when it extended the Ivy pool with a well in the Palo Pinto limestone from 3145 to 3183 ft., and was estimated good for 6,000,000 cu. ft. of gas and 6000 bbl. of oil per day. During 1938, Stonewall County obtained its first commercial producer when the Stonewall Oil Co. in No. 1 Parriott discovered the Palo Pinto limestone saturated from 5169 to 5176 ft. and tested 371 bbl. per day. Two new producing horizons were discovered about 2 miles east of the old Noddle Creek pool, Jones County; the first, the Humble Oil & Refining Co. No. 1 Irvin, in sec. 48, block 18, T. & P. R. R. Co. survey, which had saturated limestone from 2550 to 2567 ft. and was good for 100 bbl. per day; the second, in the Humble No. 1 Horton, sec. 40, which

Jan 1, 1939