Search Documents

By Emile Hiertz

THE first press was installed in June, 1910, and the second in March,1911. They produce 1,000 briquettes per hour, weighing 5 kg. (11.05 1b.) each, under a pressure of about 400 kg. per square centimeter (5,689.2 lb. per square inch). The chloride of magnesium is received from the potash mines at Hanover in tank cars in approximately a 35 per cent. solution. The quantity of solution added to the flue dust varies between 2 and 3 per cent., so that the briquettes contain about 1 per cent of MgCl2. To fresh dust as much as 10 per cent. of coke breeze may be added and bri¬quettes made that still have a crushing strength of from 25 to 30 kg. (377 to 426.6 lb. per square inch) after 36 hr., and 45 kg. (639.9 lb. per square inch) after six days. After having treated 140,000 tons of the material, the reports of the blast furnaces show that the briquettes improved the action of a furnace and produced less dust than did Minette ore. As much as 35 per cent. of briquettes is added to the furnace charge without bad effects on operations. The presence of chlorine did not produce any corrosion in the furnace, downtakes or other piping. The presence of a certain amount of chlorine in the dust reduces the amount of chloride of magnesium which it is necessary to add for briquetting.

Jan 12, 1913

By George B. Clark

THE geological data emphasized so successfully in prospecting for new deposits, that is, structural controls, strength of solutions, and type of mineralization, are basically those required for successful exploitation. In the mining of newly discovered deposits the most economical methods should be employed as early as possible to keep the overall cost per unit produced at a minimum and to permit maximum extraction of valuable minerals. A crucial question is: How can geological data be translated into useful quantitative results which will aid in achieving this end? H. E. McKinistry1 has suggested that a solution may be reached in one of two ways: 1-the usual approach, use of judgment based on experience; or 2-mathematical calculations and tests on models, both subject to certain limitations. He also suggests that in addition to better use of geology more case data and theoretical data are needed on which to base sound judgment. Further research, therefore, is necessary. Perhaps in this field the emphasis should be on more specialization in mining methods and ground movement by men with thorough training in physics, engineering, geology, and underground mining. These specialists would be equipped to point out the most economical and scientific methods of exploitation.

Jan 8, 1954

By W. W. Odell

THE sulfur content of coal is perhaps more important in the manufacture of illuminating gas than in any other coal-using industry. Whether the gas is made by the distillation of coal in retorts or ovens or by steaming incandescent coal or coke in the water-gas process, a portion of the sulfur present in the fuel always passes into the crude gas. Practically all the sulfur that remains in the finished gas is transformed into sulfur dioxide (SO2) when the gas is burned. Sulfur dioxide is a pungent suffocating gas and, if present in the air in any perceptible amount, is deleterious to health and comfort and damaging to house furnishings. So universally is this recognized that laws regulating the amount of sulfur that may be permitted to remain in the gas are very generally in force. The capacity of a plant to purify gas frequently limits the selection of coal for gas making. This condition may arise from different causes. Some plants were originally designed to handle a certain grade of low-sulfur gas coal, and very little leeway was allowed for growth or for the use of inferior coals. Other plants, when built, had ample capacity to purify gas from relatively higher sulfur coals, but their output has grown so rapidly that their purifying capacity is now limited and only- the low-sulfur coals can be handled. There is a great quantity of coal in the United States that would satisfy the requirements of the gas manufacturer, were it not for the high sulfur content. The coals containing less than 1 per cent. sulfur are becoming scarcer year by year and, in time, the gas industry will probably be compelled to use coals that are now considered out of the question.

Jan 9, 1919

By Thomas H. Sheehan

The purpose of this paper is to present an application of computer technology to assist the mineral company financial executive in assessing exchange risks. The paper is divided into five parts: Background, Translation Approaches, Theory, Empirical Validation, and Conclusion. BACKGROUND Exchange risk results from a change in the rate of exchange between a host and a home country's currencies. Legitimate reasons exist for changes in the currency exchange rates among countries in a world with over a hundred different currencies. These reasons include: different economic growth rates, social factors, cultural heritages, and political motivations. The problem of exchange rate changes are perennial and exist whether the world operates on exchange rates or floating exchange rate practices. The cause of the problem is trade and international payment imbalances. If one accepts the premise that exchange rates fluctuate over time, then the mineral company financial executive faces a continual process of reassessment of the impact of exchange rate changes on the financial worth of his company. (1) The mineral company financial executive prepares balance sheets and income statements that are audited by certified public account- ants annually for shareholders, bankers, and tax authorities. The financial executive translates assets and equities denominated in foreign currencies into domestic dollars, e.g., Japanese firms convert to Yen, French firms convert to Francs, and so on. When figures from foreign subsidiary operations are consolidated into the balance sheets of the parent corporation, estimates of the company's finan-

Jan 1, 1977

Transit A light weight, totally enclosed theodolite, especially designed for mining, has been placed on the market by Askania Werke, A. G. The instrument weighs only 41/4 lb and measures 51/8 x 71/2 in. without tripod and in a waterproof aluminum hood. It may be mounted on tripod or bracket without removing the protective hood. [ ] Standard equipment includes diagonal eyepiece rotating in all directions which eliminates need to be in line with scope for sighting and makes an auxiliary scope unnecessary for steep sights. The transit reads direct to 1 minute and may be estimated to 6 seconds by means of optical micrometer on both horizontal and vertical circles. The telescope in vertical position serves as optical plummet, sighting through an opening in the base. The instrument is shown above mounted for attaching to a pin driven in timber or rock, eliminating tripod or set-up bar in cramped quarters. The chain clamp in the lower picture is used on timber or steel ground supports. Complete with carrying case and set-up brackets, ready for use in a raise, it weighs less than 6 lb, and the protective hood remains on until the instrument is securely mounted. [ ] Accessories for increasing versatility of this mining theodolite are: tripod, electric illumination for optical micrometer and reticule, close range objective lens, and objective lens prism for sighting vertically in front of the instrument. Circle No. 1

Jan 1, 1952

W. Morton Webb, Germiston, Transvaal, South Africa (communication to the Secretary*):—The experience of Mr. Boeh-mer in the Leadville district and his reputation as an engineer assure the interest of anything he may write on the ore-bodies of that district; and all engineers who have operated in Leadville will agree that the theory of the origin of the Leadville deposits, as given by Mr. Emmons in his famous monograph, does not adequately explain the genesis of all the deposits. The solutiou of the problem does not, however, appear to be quite so simple as Mr. Boehmer would make it; and the advance pamphlet issued by the U. S. Geological Survey, pending the completion of the main report, shows that there is still much ground for controversy. No doubt the later eruptive0 had a greater influence on the deposition of the ore-bodies than was thought at the time of the first investigation by the Survey; but it has always appeared to me that the influence exerted by these dikes mas more in the nature of a physical than a chemical one. The weight of evidence in recent years is mostly in the direction of ascension rather than lateral secretion; and one of the strongest evidences is the fact that most of the ore-bodies lie under one of the comparatively impervious layers which help to make up the structure of these hills.

Jan 1, 1911

By O. B. Hopkins

DuRing 1931 Peru lost its place as ninth among the oil-producing countries of the world, to Argentina, and even in tenth place its production only slightly exceeded that of Trinidad. The preliminary figures for 1932 indicate that Peru will lose tenth place for that year to Trinidad. The production in barrels of the three coastal fields of Peru during the past three years was as follows: In addition to this crude production, the International and Lobitos companies produced approximately 770,000 bbl. of casinghead gasoline during 1932. There was no outstanding development in the oil industry in Peru during 1932; activity in the fields was very much restricted due to curtailment of production and the low price of oil. The potential production of the property of the International Petroleum Co. Ltd. greatly exceeded the actual production. By the beginning of 1932, a total of 2348 productive wells had been drilled on the property of the International, of which 547 had been abandoned, leaving 1801 productive wells at that' date. These wells cover a total productive area of approximately 13,500 acres. The crude produced has an average gravity of 37° to 38° Be. The Lobitos crude is of approximately the same gravity. The earliest oil pool developed in the Peruvian Coastal area is now more than 40 years old and is still producing. The major development in the area took place between 1920 and 1930. Production at the present rate can be maintained for 10 years or more.

Jan 1, 1933

By Joseph Pogue

OVER a period of years the writer has presented a number of studies1 on various aspects of proration, in a progressive attempt to analyze critically and constructively the economic complexities of this interesting institu-tion, which in a decade has revolutionized the economics of oil production in the United States. In the course of the investigations leading to these papers, the changing nature of proration and the principles under-lying its evolution have gradually become clear, so that it is now possible to depart from the analytical method and to construct a synthesis of the steps that, if furthered by the industry, should carry proration past the economic hazards that still surround it to the goal of maximizing the value of the petroleum resource to the industry and the public alike. NATURE OF PRORATION Proration literally means the allocation of demand among competing producers on a pro rata basis, but the term now carries a much broader significance for it is employed to describe the entire process by which the production of crude oil in the United States is regulated. There is naturally much confusion of thought on the subject, for proration is an evolving system of control based upon principles of conservation and equity and embracing a body of practices that are tending to adjust themselves to the needs of the situation but are subjected to varying and divergent influences in the process. As it is now constituted, proration is a planned production measure designed to prevent waste, insure ratable takings, and balance supply and demand. The procedure is administered by State regulatory bodies through use of the police power of the States under authority of State conservation laws; the practice is supported by a considerable degree of voluntary conformance on the part of operators; and the Federal Government has accorded its cooperation by providing advisory quotas, circumscribing imports, checking movements of hot

Jan 1, 1939

By R. A. Bowen

THE Montreal mine, operated by the Montreal Mining Co., is four miles west of Ironwood, Mich., in Iron County, Wisconsin. It is the westernmost producing property on the Gogebic Iron Range of the Lake Superior district. Its production is 4000 tons of hematite per day from an average depth of 2300 ft. This tonnage is hoisted through a five-compartment vertical shaft. Several mining methods are in use but in the larger orebodies the method is sublevel caving. ORE OCCURRENCE AND CHARACTERISTICS The main orebodies of the Montreal mine lie in eastward-pitching troughs formed by the intersections of intrusive dikes with impervious members of the iron formation. The formation has an average width of 425 ft., strikes east and west and clips north at approximately 62°. The dikes dip south at 45° and bear north 20° from the strike of the formation, making the intersections with various members pitch east at 16°. The dikes are not continuous across the formation but are interrupted ,by a longitudinal bedding fault, which has a throw of 380 ft. vertically and 885 ft. horizontally. North of the fault zone the formation is called "hanging," south it is called "footwall" formation. The faulting has created two ore-bearing horizons; viz., at the inter-section of hanging dikes with the slate members and the foot dikes with the quartzite footwall. In each formation the main ore-bearing member consists of wavy beds of hard chest interlaid with hematite. In the most productive part of the mine, where the sublevel caving method is employed, a hanging-formation dike lies in juxtaposition with a footwall dike and the iron formation carries ore in certain sections from the quartzite footwall to the hanging (like. Here a horizontal section of the orebody may be 300 to 400 ft. wide for a length of 150 ft. or more and tail out lengthwise in both the foot and hanging formations. The footwall ore section is much longer than the hanging wall because of the orebody's greater height above the "pitching dike."

Jan 1, 1938

By G. Gutierrez, M. C. Fuerstenau, J. D. Miller

The response of pure goethite and two natural iron ores to flotation with potassium octyl hydroxamate is presented. The ores contained 12.5% and 39.7% iron; concentrates containing 69.5% and 61.5% iron, respectively, were obtained with additions of 0.4 lb/ton hydroxamate. Selective flotation of iron oxides from associated gangue minerals has proven difficult in the past with standard collectors, such as sulfonates and fatty acids. As a result, recent work has been directed toward silica flotation with calcium activation after the iron oxide surfaces have been blinded with certain starches.& The results obtained with this technique are encouraging. This method, however, involves depressing a mineral that would normally float under the conditions employed. A preferable method would involve floating the iron oxide because quartz is naturally depressed until activated. Earlier work involved this approach, but in view of the results obtained, collectors that exhibit greater specificity for iron are needed. During an investigation of chrysocolla flotation with potassium octyl hydroxamate, a metal chelate former, it was observed that pyrite floated well with low additions of collector.3 This phenomenon suggests that hydroxamate has a rather strong affinity for iron, and that other iron-bearing minerals should also respond to flotation with octyl hydroxamate. The object of this paper is to determine this response. The experimental work was divided into areas, the first of which involved microflotation experiments with pure goethite with an apparatus described previously.4 Goethite was selected because of the ease

Jan 1, 1968

By W. S. Gatley, F. C. Appl

This paper presents a combined analytical and experimental study of chisel penetration vs time during chisel impact on rock, a problem of fundamental importance in improving the performance of roller-cone bits or percussion drilling toots. For a given force-time relationship between chisel and rock, the problem of determining the penetration (displacement) vs time of the chisel is formidable. This is so because the rock is a nonlinear system with distributed mass and distributed damping (friction, dissipation of energy due to rupture, etc.). Since the literature does not contain adaptable solutions, the rock behavior to impact was simulated approximately by an "equivalent" lumped system, that is, an "equivalent" mass, spring, dashpot system. With this assumption, an analytical solution was found for chisel penetration vs time due to a sinusoidal load between chisel and rock. From this solution were found curves, in terms of dimension-less variables, for the maximum depth of penetration vs the frequency of the sinusoidal loading and for the energy transfer vs frequency. The results of this analysis were used to predict the penetration rate of rotary rock bits us rotary speed. The curve indicated that an optimum speed exists. To verify this analysis, an experimental apparatus was constructed and used to apply a sinusoidal pulse to a chisel penetrating a rock specimen under atmospheric conditions. Strain gauges were mounted on the chisel shank and a velocity transducer was mounted between the chisel and the rock surface. The velocity was integrated electrically and picked up simultaneously with the strain gauge signal on an oscilloscope. Permanent records were made photographically to provide simultaneous records of force us time and penetration us time. In comparing the experimental results for limestone and dolomite with the theoretical results, good agreement was found in the frequency range of the experiments. Unfortunately, the inertia effect (peak penetration) indicated by the theory occurs at a frequency much higher than could be obtained experimentally with the apparatus constructed. A "rate-of-loading" effect is indicated theoretically, but has not yet been verified experimentally. INTRODUCTION The process of drilling with percussion tools or rotary rock bits is basically related to the transient response of rock to surface impact. Each time a bit tooth contacts the rock, high stresses are developed which result in penetration and rock removal. As the tooth moves on, stresses are relieved and a new cycle begins as the next tooth contacts the rock. Thus the drilling process, which consists of an endless succession of these cycles, can be studied in terms of a single cycle. It is apparent, therefore, that the study of single-chisel impact on rock is fundamentally important in improving the performance of roller-cone and percussive-type drills. Previous studies in this area have been conducted by Simon1 and Hartman2 by means of drop tests. In these tests a chisel was attached to a weight and allowed to fall, due to the force of gravity, so that the chisel was driven into a rock specimen upon impact. Strain gauges were attached to the chisel shank and the resulting force-vs-time curves were recorded photographically from an oscilloscope screen. The depth of penetration and crater dimensions were also measured. These tests have provided much valuable information but, as mentioned by the investigators, have not provided complete information on the effect of "rate of loading'! This is partly due to the fact that the chisel motion during drop tests is not a controlled motion which can be varied in form and frequency. Therefore, it seemed that additional information could be obtained by studying chisel impact under conditions where both the motion and the frequency of loading could be controlled. This paper presents a combined analytical and exper-

"The cleanliness and system evidenced in the accompanying photographs of the West Steward change-house will appeal to all mine operators. This design is the most efficient in use at Butte. It is the standard which will probably be used in Butte in all future construction and is the result of a long period of investigation and experimenting. It is important that such a structure be as nearly fire-proof as possible, because of the frequent fires originating within the lockers from matches, etc., in the men's clothes. The concrete floors permit the thorough washing of the building whenever necessary.The lockers are roomy and well ventilated. They are constructed of sheet steel and are warmed from below by steam pipes."

Jan 1, 1913

By L. C. Morganroth

From a geological standpoint, but scant attention has been paid to fire-clay beds. Only within the last few years have they been the subject of individual investigation, prior to this time having been considered only in their relation to coal seams. While the relative importance of coal and fire clay is still immeasurably in favor of coal, yet an industry as large as that of fire clay is entitled to a measure of attention. A discussion of the Carboniferous clays is practically a discussion of the clay beds in the Appalachian basin, since more than 90 per cent. of these clays mined are from this region. The clays are confined to the northern end of the basin, or the States of Pennsylvania, Ohio, Kentucky, Maryland and West Virginia, ranking in importance about in the order named. The clay deposits of the Carboniferous period have been divided into two classes; those found in the Pottsville conglomerate series of rocks, ' and all those that are found in the formations above, for the reason that the clay beds above the Pottsville series all resemble each other in properties, composition and appearance, and all are distinctly different from the bed found in the Pottsville formation. The bed of clay found in the latter formation is unique in that flint clay is practically restricted to it. (A variety of flint clay is occasionally found in these upper deposits but this is in such small amounts as to be negligible.) Carboniferous clays occur between stratified rocks; sandstones, limestones, etc., in the same manner as coal veins. They are often accompanied by a coal vein although where the clay is of a workable thickness, the coal is generally too thin to work. The clay beds are sometimes known by the name of the coal seam at which horizon they occur. Clay beds may be from a few inches up to 20 ft. in thickness. They may consist of all soft clay, all flint or both soft and flint. The Carboniferous clay beds of Pennsylvania are the most important of any of the clay beds found in the country, and are among the oldest ones worked. We know more about this clay geologically for the reason

Jan 1, 1916

By Elton A. Youngberg

The Holden mine operated by the Chelan Division of the Howe Sound Co. is on the east slope of the Cascade Range in north central Washington on the south slope of Railroad Creek valley at an elevation of 3500 ft. The mine may be reached by a 40 mile boat trip from the town of Chelan which is at the southern tip of Lake Chelan, to Lucerne at the mouth of Railroad Creek and an 11. mile bus ride up Railroad Creek to Holden. A11 freight and concentrate is moved over this route to Chelan Falls on the Columbia River which is on the railroad four miles below the town of Chelan. The mine is now producing 2000 tons of gold, copper, and zinc ore per day which is treated in the Holden mill. Gold-copper and zinc concentrates are made, the first of which is shipped to Tacoma, Wash., and the latter to Kellogg, Idaho, for smelting. Ore is broken by long-hole blasting using the Noranda system which has been modified to meet local conditions. Until recently, blastholes have been drilled by diamond drills. Now a partial substitution of percussion drill holes, drilled with tungsten carbide insert bits, is being made. Geology The ore body occurs as a replacement deposit in a highly metamorphosed series of sedimentary rocks, mainly gneiss and schists, in a shear zone several hundred feet in width and of undetermined length. Commercial ore has been found in mineable widths of 25 to 100 ft for approximately 2500 ft along its strike. The commercial minerals are chalcopyrite, sphalerite, and gold. During the period of mineralization considerable silicifica-tion took place giving the ore an abrasive drilling characteristic. Following the period of mineralization, numerous dikes were introduced into the ore body. The earlier ones were of granite composition having a width of a few inches up to 80 ft. These were followed by much younger, fine grained basic dikes which usually do not exceed 2 ft in width. Development of Percussion Blasthole Drilling Equipment Test work with the 1½-in. tungsten carbide bit was carried on in development headings for several months early in 1947. The short life of the bits, because of gauge loss caused by the abrasive nature of the rock, prevented its adoption for this use. However fast drilling speed and ability to drill a long uniform hole suggested its use for drilling blastholes in competition with diamond drills as diamond costs were steadily increasing and exper-ienced drillers were difficult to obtain. The 1½-in. bit was the largest available at the time initial test work was started with sectional steel. The 1½-in. hole limited the diameter of the steel thread and coupling which could be used. Type F couplings were first used but because of the small thread section excessive breakage of the steel was experienced. Type H couplings were tried next. In order to use this coupling which is 15/8 in. in outside diameter, it was reduced to 1 3/8 in. giving 1/8 in. clearance between the coupling and the hole. Rod breakage at the thread was substantially reduced but some coupling breakage was experienced, however the overall performance was considered satisfactory (see Fig 1 for illustration of coupling and thread). Early test work with the 1½ in. bit indicated machines of piston diameters larger than 255 in. would cause inserts to loosen or break. It was found however that the additional weight of the sectional steel cushioned the blow enough to prevent bit failures when 3-in. Leyners were used. Rods used with the 1½-in. bits were 7/8 in. q. o. for sectional steel and 1 in. q. o. for all chuck pieces. In May 1948, 2-in. tungsten carbide bits became available and test work was immediately started. The 2-in. hole approximated the AX (1 15/16 in.) diamond drill hole which was being used exclusively for blastholes and permitted their substitution for diamond drill holes in a ring without alteration of pattern, burden, or explosives. The 2-in. bit also gave room in the hole for larger couplings and permitted the use of heavier rods and 3½-in. machines, increasing the

Jan 1, 1950

By J. R. CAIN

SAMUEL L. HOYT, ? Nela Park, Cleveland, Ohio (written discussion?). The work that Dr. Cain is doing on gases in steel should have a highly important bearing on investigational work in connection with steel-making practice. We found, for example, in our work in connection with the use of manganese in open-hearth practice that we needed expressions for the manganese efficiency and the "condition" of the steel. To get these figures we assumed that we would need to know the amount of FeO at different stages of the heat and the amounts of the gases present. This required simultaneous analyses of our samples for FeO and the gases and Dr. Cain seems to be the only investigator who has considered the analytical work from this point of view. That he has done so is very encouraging and it is to be hoped that his work will solve the mys-teries now surrounding this neglected phase of steel metallurgy. Those interested in the Ledebur method for use in connection with the efficiency of manganese as a "deoxidizing " agent will he disappointed to learn that more recent work at the Bureau indicates that Ledebur determinations are not reliable. The principal source of error seems to be due to the partial reduction of the ferrous oxide by the carbon present in the steel. However, it seems like an unnecessary criticism of the Ledebur method to state (p. 1319) that it proved of little value because it showed little differences in oxygen for a series of steels treated with ,various reagents and showing variations in physical properties and free-

Jan 12, 1919

By H. R. Crawford, P. B. Crawford, A. F. Tragesser

A method has been developed to calculate wellbore temperatures during mud circulation and the actual cementing operation to aid in the design of cement slurries. The method agrees within 10F with previously measured values. The calculation technique provides temperatures, as functions of time, at varying depths in both the casing and annulus. The technique also provides this information if a relatively cool cement slurry is pumped into the well immediately following circulation of hot mud. Circulating bottom hole temperatures of brine and a bentonite mud were measured. INTRODUCTION As wells are drilled deeper, greater demands are being made on all phases of the industry, and new technology has been developed to provide satisfactory well completions. However, little or no work has been conducted on accurately determining bottom-hole, static and circulating temperatures.. In designing a cement slurry, such factors as density, fluid loss control, viscosity, deterioration from ternperature, compressive strength and pumping time must be considered. Individual well conditions often make it necessary to include still other factors. Pumping time is a primary consideration and, as wells are drilled deeper, encountering higher bottom-hole temperatures, this property becomes even more important. Cement slurries must be designed with sufficient pumping time to provide safe placement in the well; however, the slurry cannot be overly retarded as this will prevent the development of satisfactory compressive strength. The pumping time of a specific cement is currently obtained by subjecting the cement to simulated conditions of temperature and pressure. A reasonably accurate bottom-hole pressure may be obtained by considering hydrostatic heads of fluids, friction pressure and wellhead pressures. However, accurately determining bottom-hole temperatures is much more difficult. Bottom-hole static temperatures are estimated by considering several sources of information, including logging temperatures, published temperature gradient maps and field experience. This information is usually questionable due to disagreement of data from the various sources. Temperature gradient maps were constructed based on temperatures recorded many years ago while running bottom-hole pressure tests. These thermal gradients then represent an average of well conditions and cannot always apply to a specific well. Also, logging temperatures may be affected by the time since fluid was last circulated, rate of penetration, circulating rate and many other factors. Therefore, even though logging temperatures are available, the question still exists as to the correction factor that should be applied to obtain an accurate static temperature. After obtaining static bottom-hole temperature, it is then necessary to relate this to circulating temperatures actually encountered by the cement slurry. This is accomplished by selecting a test schedule from the API RP-10B corresponding to the estimated well conditions.' The API-recommended practice for testing oilwell cement provides testing schedules for various well depths and conditions. These schedules are intended to simulate down-hole conditions during cementing. They provide a rate at which both temperature and pressure are increased until the estimated circulating conditions are reached. These testing schedules represent circulating temperatures for an average well and, although there is flexibility in choosing the test schedule that most accurately simulates the temperature of an individual well, it still is not possible to consider all the well conditions that will affect the bottom-hole temperature. Many factors affect cement temperatures; for example, the length of time a well has remained static prior to running casing and cementing, the circulation time, the temperature of fluids used in cementing, fluid density and flow properties of fluids. The pumping time for a typical retarded cement could vary from 2 to 4 hours with a 10F change in testing temperature. Variations in pumping time are the most critical in highly retarded cements used in deep, hot wells; yet, predicting bottom-hole circulating temperatures is more difficult in these wells. This work was conducted to develop a means of calculating circulating temperatures as a function of well depth, casing and hole size, pumping rate and time, fluid and reservoir physical properties and thermal status of the well. PREVIOUS WORK In 1941 Farris reported on a study to develop information leading to a more practical laboratory evaluation of oilfield cementing mixtures and performance.' It was then recognized that the pressure factor was being neglected,

By E. H. Barton

The necessity, on the Pacific Coast and throughout the semiarid regions in particular, of the conservation of waters for agricultural, industrial and mining purposes has forced itself upon the minds of those directly or indirectly interested in these industries. To meet the requirements of the case, storage must be provided for the flood-waters so abundant during the rainy season in order to insure a constant and unfailing supply during the summer months. Such storage can only be obtained, in the greater number of instances, by the erection of reservoir-walls of great height. The feasibility of employing earth or timber in the construction of such high dams is questionable, especially when (as is often the case) they must be placed in torrential streams. The experience of recent years with masonry dams, throughout this and foreign countries, has demonstrated that such dams, when intelligently and correctly designed and properly constructed, will meet the requirements of larger storage by means of increased height. The failures of masonry dams have been few; only two of any consequence being on record, namely, that of the Puentes dam, in Spain, in 1802, and that of the Habra dam, in Algiers, in 1810.* On the other hand, the failures of wooden and earthern dams are innumerable. The following are some of the most important structures constructed in recent years. The list is taken from Mr. Wegmann's book, just cited: The Furens, Zola, Ternay, Ban and Verdon dams, in France; the Nizar, Lozoya, Villar and the two Hizar dams,

Jan 1, 1900

By Sandford S. Cole

Manganese compounds occur in many mineral forms widely distributed throughout the crust of the earth. The most important of these commercially are the oxides which are usually found as irregular masses, but in some places (notably U.S.S.R.) occur as extensive beds of varying thickness and purity. The principal sources of ore have been U.S.S.R., Ghana (the Gold Coast of Africa), India, Union of South Africa, Belgian Congo, French Morocco, Cuba, Brazil, and Mexico. New developments of ore are being conducted in Brazil, British Guiana, French Equatorial Africa, and Northern Rhodesia. The production of the United States normally meets less than 10 pct of domestic manganese consumption. Manganese ore (35 pct or more Mn) is used principally by the ferrous metallurgy industry for production of manganese metal, ferromanganese, and other manganese alloys for use in production of steel ingots and castings. Some manganese is used in the nonferrous industry as an alloying element and cleanser in aluminum alloys, aluminum bronze, constantan, manganese bronze, Monel, Everdur, nickel-chromium resistance alloys, and nickel-silver. The metallurgical uses consume about 97 pct of the total manganese ore requirements of the United States. The balance goes principally for the manufacture of dry cells and for chemicals, with limited amounts for ceramic products, plastics, welding rods and varnish. The Materials Survey on Manganese, compiled in 1952 for Materials Office National Security Resources Board by the Bureau of Mines and Geological Survey, provides an excellent review of resources, reserves, specifications, uses, mining, beneficiation, metallurgical processes and deposits, and is worth referring to for greater details. Mineralogy and Geology The more common manganese minerals with typical characteristics are listed in Table 1 in order of importance. [ ]

Jan 1, 1960

By Erwin S. Sperry

Some time ago, the author had occasion to make an alloy of equal parts of nickel and aluminum, for the purpose of adding small amounts of nickel to pure aluminum. The nickel was melted in a plumbago crucible under a layer of borax ; and at a proper temperature the aluminum was added, and the whole mass was stirred with a plumbago stirrer. The alloy immediately became incandescent and boiled. It was then poured into iron moulds, in the form of ingots weighing about 10 pounds. The metal when poured was very fluid and free from the viscosity so often noticed in nickel and nickel-alloys. The color of the alloy is gray, not unlike that of wrought-iron, and the fracture is devoid of any crystalline appearance. It is quite brittle, and can be readily ground to a powder in a mortar. More metal was made than was needed; and what remained unused was placed in a covered wooden box and set away. In about three months, as it mas again necessary to use the alloy, the box was opened; and, much to my surprise, nothing but a dark gray powder was found in it. This condition of the alloy could not be accounted for. An attempt was made to melt the powder and pour it again into ingots, but with negative results. Analogy pointed to disintegration; and it was decided to make a fresh sample of the alloy, and watch the material from the beginning. In the second experiment the conditions were identical with those of the first, with the exception that fluor spar was substituted for the borax. This change was made because it was thought that perhaps the borax might have been

Jan 1, 1900

By Harry H. Power

WHILE the attention of all engineering branches is focused today on changes and improvements in the several curricula, we are concerned here with the many questions arising in industry and college concerning the preparation for the petroleum engineering profession. The succession of problems confronting the petroleum engineer demands a degree of versatility not ordinarily encountered in other professions. As a consequence, the student cannot acquire mastery of all the several engineering branches represented in field practice, and as an alternative, he has learned to appreciate the value of thorough training in the basic or fundamental sciences as a preliminary foundation for professional work. While our attention is directed primarily to the training of engineers in educational institutions, it is necessary that the ultimate education of the professional engineer be kept in mind. It is apparent that his success as an engineer is limited not only by his educational and job experience, but by his native endowments: mentality, personality and health. The engineer's lack of job experiences often proves as much a handicap as the lack of adequate college training. If the final product proves to be satisfactory, both industry and technical institutions are to be congratulated. However, if the product is found wanting, the one most responsible should be apprehended. FITNESS FOR PROFESSION For the most part, students of engineering colleges have had their interests in applied science awakened at a relatively early age. Many of them entered college as a convenient means of acquiring a technical education, but undoubtedly would have had better prospects in a shorter program offered by institutions of noncollege grade. The activating motive of practical interest is also strong in students suitable for college training, but in many cases an intellectual interest must be awakened in order that it may survive graduation. Numerous engineers believe that this progressive process of selection and determination of career aims is one of the essential services rendered by the engineering colleges. Industrialists, who are more interested in quality than quantity of petroleum engineering graduates, have pointed out the good that should result if more empha¬sis were given to the work of eliminating the misfits. They also point out the protective measures that have been taken by other professions for the betterment of professional standards. Mention has been made of the beneficial results to be obtained by collective determination of the market for the products of engineering schools, particularly in that the students unsuited to the profession would have an opportunity to prepare themselves for employment more suited to their personalities and other qualifications. In the event that such a system of coordinated personnel direction is developed by the

Jan 1, 1941