Search Documents

By D. C. Seidel, E. F. Fitzhugh

The cementation of nickel from acidic solutions by metallic iron is discussed. The cementation is carried out in pressure vessels at temperatures above 100°C. The results from bench scale studies on variables such as retention time, temperature, and solution pH are presented. A continuous processing flowsheet is proposed. Cementation is one of the oldest known hydrometal-lurgical reactions. The cementation of copper on iron was recorded by 'Paracelsus the Great' in about 1500,1 and by 1600 the technique was being used to recover copper at the Rio Tinto operations in Spain.2 At least one early author felt that cementation may have been one of the primary reasons for the alchemists' belief in the transmutation of metals.' The early writings state that when iron was placed in the clear waters from some mountain springs, the iron disappears and copper is found in its place. To the alchemists this may well have been one of the most convincing proofs that transmutation could and did occur. Since these early times the recovery of copper from acidic solutions by cementation has been practiced in plants throughout the world. Probably the cementation technique in some form has been common to more copper mining and milling operations than any other single recovery process. During current hydrometallurgical extraction studies, which were sponsored by the Republic Steel Corp. at the Colorado School of Mines Research Foundation, Inc., it was found that under the proper conditions, metallic nickel could be cemented from acidic solutions by powdered iron. The reactions are apparently similar to those that occur during the cementation of copper, but the nickel cementation had not been anticipated because iron and nickel are nearly adjacent in the electromotive series. The potential difference between iron and copper is approximately 0.78 v, while the potential difference between iron and nickel is less than 0.21 v. The cementation of nickel with iron at room temperature is almost negligible, but when the reaction is carried out in a closed vessel at temperatures in excess of 100°C, the nickel can be cemented almost quantitatively. The part played by this discovery in a practical method of nickel recovery is set forth in a separate paper.3 The following paragraphs are a discussion of experimental studies that were made to investigate this cementation reaction. The technique has been designated the HTC or High Temperature Cementation procedure. The cementation work was part of a study on hydrometallurgical techniques for the extraction of nickel from the garnierite or silicate type nickel ores. A hydrothermal extraction procedure had been developed, and this technique produced an acidic pulp or solution that contained both nickel and appreciable amounts of magnesium.3 Small quantities of ferric and ferrous iron were also present along with cobalt, manganese, and chromium. The potential for recovering the nickel from these acidic solutions by ion exchange or solvent extraction did not appear to be promising because of the relatively high magnesium content. The Ni ++ and Mg++ have nearly identical ionic dimensions and tend to be co-absorbed or extracted during ion exchange or solvent extraction treatments. Preliminary tests indicated that the nickel could be precipitated as a sulfide when using the high pressure H2S precipitation technique developed for the Moa Bay operations of the Freeport Nickel CO.4 This technique gave good recoveries, but the nickel sulfide product requires considerable additional processing before a marketable form of nickel is realized. The process also requires clarified feed solutions, and the solids-liquid separations on the garnierite residues are difficult. A program was initiated to investigate alternate procedures that might shorten the route to a marketable nickel product, and hopefully also permit bypassing the difficult solids-liquid separation steps required for the H2S precipitation technique. It was during these studies that the nickel cementation reaction with iron was encountered. EXPERIMENTAL EQUIPMENT AND PROCEDURES The bench scale precipitation tests which were conducted during this experimental program were made in 2-liter stirred autoclaves.* A photograph showing the form and arrangement of the autoclave

Jan 1, 1968

By F. C. von der Weid

THE mining district of São Fidelis, in the northern part of the State of Rio de Janeiro, is situated on the Paraiba River, where it crosses the Serra do Mar (Mountain of the Sea), in the center of a mountainous country having numerous graphitic outcrops. For a long time, these outcrops were irregularly explored by local people, who had little means and no technical advice. A few years ago, the Cia. Brasileira de Mineração de Grafite took over the control of some of the more important outcrops and entrusted to me the task of studying the ores and establishing a flowsheet for a pilot plant to be situated in Sao Fidelis-the ore to be concentrated being mostly of a very high grade. MINERALIZATION AND ORES The rocks of the district are mostly gneiss and crystalline schists, with occasional interstratification of dolomitic limestone belonging to the Archean Brazilian Fundamental Complex. The general direction of the beds is roughly between 60° and 80°E., with variable dip, generally nearly vertical. Mostly, direction and dip of the graphitic outcrops is concordant with the embanking gneisses or schists. These outcrops seem to be aligned in two or three parallel zones (Pádua, São Fidelis, Macabú), the São Fidelis zone being the best known and the most important to date. Two outcrops of the São Fidelis zone, Saudade and São Benedito, are now being exploited. Mining has been carried out, so far, on a small scale. The mineralization consists of a vein of nearly massive graphite in a very compact, partially granitized gneiss, with vertical dip. The vein is most irregular, with nests and lenses irregularly distributed along the fracture plane. The ore consists chiefly (particularly in São Benedito) of massive graphite appearing and disappearing along the main direction of the vein, forming a succession of irregular lenses in a sort of rosary design. The average width is more or less one foot, with variations from zero to 6 feet. The lode minerals are quartz, a little feldspar and garnet (the latter having its origin perhaps in the embedding gneisses), with rare ferruginous clays on the outcrops. In Saudade a little pyrite, pyrrhotite and chalcopyrite is found occasionally, as well as a carbonaceous mineral, very light, black and shiny, with conchoidal fracture, looking like a sort of jet. The composition of this mineral has not yet been established, but it seems to be very complex. The mineralization seems to be hydrothermal at a rather low temperature, perhaps mesothermal. The paragenesis, according to samples from Saudade, seems to be as follows, the earlier minerals being listed first: pyrrhotite, pyrite, chalcopyrite, with quartz concomitant to the three and

Jan 1, 1946

By C. M. Young

BITUMINOUS coal piled in heaps or bins frequently undergoes a process of spontaneous heating as the result of the absorption of oxygen. It seems probable that the first absorption of oxygen by coal which has not previously been exposed to the air may occur as a condensation or a combination of oxygen in some form which does not result in the production of carbon dioxide, but slow combustion soon begins. The absorption of oxygen is accompanied by an increase of temperature, and this by in increased rapidity of absorption; hence the dangerous condition proceeds from bad to worse, until the kindling point is reached, unless the process is interrupted. A dangerous rise of temperature can be prevented by excluding oxygen, by increasing the bulk of coal in proportion to its surface exposed, or by circulating enough air to dissipate the heat produced. The storage of coal, in practice, varies from almost complete exclusion of oxygen, by storing under water, to such freedom of access as exists when the coal is stored in open piles. Oxygen available for absorption by coal is supplied by the air in the interstices between lumps and by additional air which may enter the pile through circulation. The size, of the coal largely affects both of these supplies; for if the fragments a re small the spaces between them constitute a small percentage of the total volume, and little oxygen will be available unless the circulation of air brings in a fresh supply, while with large fragments the percentage is relatively large; circulation also is much easier through a pile of coarse lumps. In the case f lump coal, although a large amount of air may be present, the exposed surface is comparatively small and there is little opportunity for the absorption of oxygen to so rapid as to cause dangerous heating. Attempts have been made to prevent heating by allowing a sufficient circulation of air to carry off the heat generated; obviously this method cannot be applied to fine sizes nor mixed sizes.

Jan 2, 1918

By R. S. Shoemaker, F. W. McQuiston

MAGMA COPPER COMPANY San Manuel Division The San Manuel Division of Magma Copper Company is located about 40 miles north of Tucson. Tons of ore milled in 1973 .were approximately 19 million at a rate of 63,000 tons per day. From this, about 42,600 tons of copper concentrate was produced as saying approximately 1.070 MoS2 and 28.5% Cu. As with many copper ores, the San Manuel ore contains a small amount of gold, but in this particular case, much of the gold follows the molybdenite. Separation of the molybdenite from the bulk sulfide concentrate by flotation produces a moly concentrate containing 9170 MoS2, just under 1.070 Cu, and 0.44 oz Au per ton. Cyanidation of this material for gold recovery is the only practice of its kind known to the authors of this Monograph. After thickening, the final moly concentrate is filtered for subsequent repulping with cyanide and lime. Gold dissolution takes place in three agitators in series with the pulp from the agitators being filtered in two stages in disc filters. Between filtration stages, the cake is repulped with barren solution. Filtrate from both filters is the pregnant solution. The Merrill-Crowe recovery unit is comprised of two solution tanks and the usual clarifying filter, vacuum tower, zinc dust feeder and Merrill precipitate press. Because of the presence of finely divided sooty chalcocite in the molybdenum concentrate, the cyanide consumption of 55 pounds per ton is extremely high. A compensating factor, however, is the low copper, moly concentrate produced. Precipitation of the gold from the highly copper-contaminated solution requires 0.56 pounds of zinc dust and 0.28 pounds of lead acetate per ton, high figures when compared to normal cyanidation practice. The Merrill- Crowe precipitate assays approximately 28.5% Cu, 8% Zn, 156 oz Au and 197 oz Ag per ton. The San Manuel cyanidation plant is an outstanding and innovative development.

Jan 1, 1975

By R. R. Angel

Drilling rate is a parameter that should be considered in determining the volume requirements for air and gas drilling. The use of past methods which ignore the effects of the solids content upon the pressure and velocity of the annulus flow stream can result in undercalculation of the required volurne by as much as 50 per cent. A vertical-flow equation is presented for determining volume requirements. This equation includes the effect of the solids that are transported up the annulus in the flow stream by incorporating the drilling rate as one of the parameters. The effect of down-hole temperature on required circulation rates is also ana-lvzed. A simple approximate method of determining volume requirements is presented. This method is more accurate than the methods used in the past. Hole cleaning difficulties are analyzed for a recent air drilling job where past methods indicated that - excess air was being used. Sample curves of calculated boitom-hole pressures are presented for air and gas drilling in several hole sizes. INTRODUCTION In certain areas the use of air or natural gas as a circulating medium for drilling oil and gas wells is becoming a common practice. Large increases in penetration rate and bit life are achieved through the use of these media in preference to mud or water. Drilling rates as high as 90 ft/hr have been obtained in shales. The importance of maintaining adequate circulation rate is generally recognized; however, much disagreement exists among drilling operators as to what constitutes "adequate" circulation rate. In quarry drilling, where annular velocities can be accurately determined, an annular velocity of 3,000 ft/min of standard air is required for best results in rocks having approximately the same density as those commonly penetrated in drilling oil or gas wells'. Although this standard air velocity has proven satisfactory for quarry drilling, some oil and gas well drilling operators believe that an equivalent annular velocity of more than 4,000 ft/min is required; others believe that as little as 2,000 ft/min . is sufficient. Much of this disagreement results from determining the required circulation rates with methods which fail to incorporate the drilled solids in an equation which is applicable to vertical flow. Hughes Tool Co. Bulletins No. 23' and 23-A3 present data for determining circulation rates based on the Weymouth formula. These data do not include the drilling rate as a parameter and, therefore, neglect the effect of the solids being transported up the annulus. In spite of this apparent defect and the fact that the Weymouth formula is not applicable to vertical flow, the Hughes data have well served the drilling industry in many areas and are important and timely contributions to the science of air and gas drilling. The Hughes data purposely omit a correction for increasing down-hole temperature. At slow drilling rates this effectively compensates for the use of a formula which is not valid for vertical flow; however, volumes determined by the Hughes method are not sufficient to support rapid drilling rates at moderate and great depths. For example, Phillips Petroleum Co.'s Cauthorn "D" No. l in the Vinegarone field for Val Verde County, Tex., was air drilled from 1,500 to 9,300 ft using a compressor delivering 1,400 cu ft/min. The 8 3/4-in hole was drilled with 5-in. drill pipe, and drilling rates as high as 90 ft/hr were obtained between 7,000 and 9,300 ft. No water or caving hole was encountered. At 7,728 ft it was necessary to wash-out 60 ft of cuttings to reach bottom after a trip to change bits. At 8,130 ft a twist-off occurred and the drill col-lars were stuck in drill cuttings. These difficulties indicate that the 1,400 cu ft/min of air was not sufficient to keep the hole clean. Hughes data indicates that 1,180 cu ft/min is sufficient to produce an annular ve-

Jan 1, 1958

By Woolsey McA. Johnson

Independently of the recognized chemical reactions involved in the production of metallic zinc, the process is affected by physical conditions in efficiency, and by commercial as well as technical economy. To offer some observations concerning these conditions is the purpose of the present paper. Among the important elements of this problem is the physical nature of the particles constituting the mass of zinc oxide to be reduced. This may be the result, either of the manner of the original deposition of the mineral, or of the treatment to which it has been subjected in the roasting-furnace. The physical character of the reducing-agent is another important factor, since the carbon of some coals is much more active in reduction than that of others. The degree of fineness, whether of ore or coal, or both, likewise plays a significant part. These factors, together with the physical admixture of foreign substances with the ore, may give rise also to chemical " side-reactions," sometimes hindering or retarding, and sometimes accelerating, the reduction. Finally, thermal conditions, including the relative conductivity of the materials, deserve to be taken into account. In firing a furnace with retorts charged with a mixture of roasted ore and coal, the first reaction is naturally the boiling-off of the contained water; the next is the distillation of the light hydrocarbons from the coal; the next is the reduction of the iron oxide to protoxide and sub-oxide successively, and then to metallic sponge; and the final reaction is the reduction of the zinc oxide in the ore by the carbon to metallic zinc. This reaction commences at 1,022o to 1,060o C., according to the physical nature and condition of the coal and ore. Since the retort and the charge are far from being good con-

Jan 1, 1908

By N. J. Gran, W. R. Opie

HYDROGEN in molten aluminum and aluminum alloys, which precipitates during cooling and solidification, is the principal cause of pin hole porosity in ingots and castings. Much attention has been given to determining the effect of temperature and pressure on the solubility of hydrogen in pure aluminum, but little data are available on hydrogen solubility in aluminum alloys. This investigation was undertaken to check results reported for pure aluminum and to show the effect of silicon and copper additions on the amount of hydrogen contained by molten alloys. Previous determinations of the solubility of hy-drogen in molten pure aluminum are plotted in fig. 1. The most reliable data appear to be those of Ransley and Neufeldl and of Baukloh and Oester-len.' The latter authors also report some results on the effect of copper and silicon additions. Up to 6 pct these elements decrease the solubility of hydrogen quite rapidly, with a definite minimum noted at 6 wt pct for both copper and for silicon, although no reason is apparent for these minima. Experimental Procedure The solubility of dry hydrogen in pure aluminum, aluminum-silicon, and aluminum-copper alloys was determined by the method of Sieverts.8 This consists of determining the volume of the gas system above the molten metal at a given temperature and pressure by using an insoluble gas. This volume is referred to as the "hot volume." The system is then evacuated and the soluble gas is introduced at the same temperature and until the same pressure is reached. It is necessary to introduce enough of the soluble gas to fill the space above the metal plus the soluble amount. The difference in the volume of soluble gas and the "hot volume" is the solubility. The accuracy of solubility measurements by the Sieverts' method is primarily depend-

Jan 1, 1951

By O. J. Huber, P. D. Frost, H. A. Robinson

URANIUM is a (ß-stabilizing, eutectoid-forming element when alloyed with titanium. Udy and Boulger1 have reported that an alloy of 48.6 pet uranium in titanium retains ß-phase when quenched from the ß-region, while compositions of approximately 30 pet uranium transform to martensite during such quenching. Since the eutectoid reaction is rather sluggish, titanium-uranium alloys should be capable of being strengthened by the ß — a trans-

Jan 1, 1959

By A. E. Wraith, N. J. Petch, J. D. Embury, E. S. Wright

The two most important parameters controlling the fracture behavior of a solid are its intrinsic properties, e.g.,grain size, and the operative stress system. The latter may be modified in laminates by the presence of weak interfaces. This is studied in notch-impact tests on a mode1 system of mild steel laminates containing a variety of interfaces. The effect of these is evaluated in terms of the ductile/cleavage transition. Two laminate geometries are distinguished, here called "crack-arrester " and "crack-divider". In both, cleavage is inhibited. This arises because of relaxation of a state of triaxial tension. In the crack-avrester laminates, cleavage initiated at a notch is confined to the layer containing the notch. In crack-cliuider laminates, a thick specimen behaves as the Sum of a number of thinner ones. Additional benefit may derive from improved intritnsic propevties of- the lanlinate layers arising from greater deformation in their manufacture. It has long been recognized that the two most important parameters controlling the fracture behavior of solids are their intrinsic properties (e.g., grain size friction stress,3 distribution of second phase particles4) and the operative stress system under which fracture occurs. In solids that show a ductile/cleavage transition, cleavage is favored by the presence of a notch. This is because triaxial tensions, generated by the localized plastic constraint at the notch, are operative when fracture occurs.= Anything that suppresses these triaxial tensions will be unfavorable to cleavage. Such suppression may possibly occur in laminates containing weak interfaces and the purpose of the present paper is to explore this possibility. Two basic laminate geometries, here termed "crack-avrester" and "cvack-divider", are examined. They are illustrated in Fig. 1. With the crack-arrester laminates, there is the possibility that, when the fracture crack approaches the interface, this, if weak, may delaminate due to the tensile stress acting parallel to the plane of the crack.= If this happens, energy will be used in delamination, the crack will be completely blunted, and the triaxial tension associated with the crack will be relaxed. To fracture the second portion of the laminate, crack reinitiation will be necessary and, because of the relaxation of the triaxial tension, this reinitiation will occur under conditions of nearly uniaxial tension, which are unfavorable to cleavage. Thus there is the possibility of cleavage suppression in the second and subsequent subunits of a crack-arrester laminate. With the crack-divider geometry, there is again the possibility of delamination at the interfaces. This will divide the crack into a series of cracks propagating through the individual laminate subunits. If these are sufficiently thin, the triaxial tension will be relaxed towards a state of biaxial tension in each of them. Thus, with the crack-divider laminates, there is again the possibility of cleavage inhibition. In the present work, these possibilities are explored using a notched impact test on mild steel laminates bonded with soft solder, silver solder or copper. Even if delamination does not occur, it is still possible that cleavage may be inhibited in laminates. With the crack-arrester geometry, the cleavage crack in the first layer may be blunted and arrested by plastic deformation in the laminate bond, if this is ductile. Partial relaxation of the stress transmitted ahead of the crack into the second layer will then result and this will reduce the significance of this stress in the fracture of the second layer. With the crack-divider geometry, there cannot be much effect in the absence of delamination unless a large amount of energy is absorbed in rupturing the ductile material. EXPERIMENTAL DETAILS The composition of the mild steel (wt pet) was: 0.04 C, 0.29 Mn, 0.01 Si, 0.006 P, 0.008 S. "As-received" plate was annealed for 2 hr at 900°C and slowly cooled to give a grain size of 0.04 mm. The laminates were made by brazing or soldering together mild steel plates 8 by 3 in. by various thicknesses. These were obtained from the annealed plate by machining, so that the intrinsic material properties were .kept constant. Laminates containing two to six steel layers were studied using standard Charpy V-notch specimens cut from the bonded plates. Standard homogeneous specimens from the annealed plate and subsize ones from the laminate components

Jan 1, 1968

By L. A. Morley, W. T. Parry

Engineering design problems encountered by mining engineers often depend on the properties of natural granular materials such as soil, poorly consolidated sediment, fault gouge, and hydrothermally produced clay. The physical properties of such granular materials frequently are determined by the properties of silicate clays. In most mining applications, the clays are in contact with water. Swelling of clay due to water infiltration can interfere with underground support and haulage systems. Water-saturated clay on fault, fracture, and bedding planes causes slope failures in open pit mines, roof falls and heaving of weak underclays in coal mines. Water may be removed and cementing agents may be produced in clays by electrical methods. When an electrical potential gradient is applied to a charged capillary by two electrodes, water moves toward the negative electrode.1 This electrokinetic phenomena is known as electroosmosis and has been used to successfully dewater clay minerals which lack strength because of water. A consolidation effect occurs when the flow of water is accompanied by a decrease in water content. Electrochemical changes in the clay result in cementing and irreversible hardening. Theory A mathematical basis of electroosmotic phenomena is presented by Helmholtz.3 Smoluchowski5 modifies Helmholtz’ model and presents Eq. 1 to describe fluid flow velocity due to electroosmosis. For this formula, the zeta potential can be measured experimentally. The Helmholtz-Smoluchowski model is reasonably valid for clay aggregates with large pores saturated with fresh water or dilute electrolyte solutions.° An assumption used for Eq. 1 (equations are given Table 1; terms are defined in Table 2) is that the thickness of the electrical double layer surrounding the clay particles is small compared with the pore radii. Because this is generally not the case, Schmid7 presents Eq. 2. The volume charge density in the pore may be approximated from cation exchange capacity and porosity measurements. Casagrande8 offers a semi-empirical relationship (Eq. 3) for volume rate of electroosmotic flow and finds that k, is relatively constant for most clays with an average

Jan 1, 1972

By W. H. Andrews

The constantly increasing consumption of Portland cement in the State makes the above subject of particular interest at this time. The increasing demand is due to the rapid settling of the country and the fact that new uses are being found frequently for the above named commercial article. The industry is one that is bound to grow as the population increases, and this being the case it may be well at this time to consider briefly the matter of the chemical and physical composition of proper raw materials. A cement mixture is one that contains approximately 75 per cent, carbonate of lime, 15 per cent. silica, and 5 to 7 per cent. alumina and iron oxides; the other elements being magnesium carbonate and mall quantities of the rarer elements generally associated with limestone deposits. It can be readily seen from the above composition that it is possible to build up this mixture from a number of different materials. First.—A rock high in carbonate of lime can be mixed with clay or shale in such proportions as to bring about the desired composition ; the chief difficulty in the building up of such a mixture is that it is hard to find a clay or shale in which the silica-alumina ratio lies between 4 to 1 and 3 to 1 and at the same time shows physical characteristics which will make certain its adaptability to the practical manufacture of Portland cement. Very often clays or shales are found which are right chemically but contain large quantities of grit or free silica. Such clays or shale must be ground to extreme fineness in the mixture in order to make the silica and alumina combine with the lime when the mixture is burned. On the other hand, clays or hales are often found that have the proper physical characteristics but in which the amount of alumina is too great. Second.—A mixture can be built up of different limestones some of which run above the 75 per cent. requirement and others below;

Jan 1, 1914

By D. R. Pratt, R. W. Hanks

The method of Caldwell and Babbitt for detennining Bingham plastic rheological constants from engineering pipe flow data has been erroneously used in many previous applications. A reanalysis of extensive pipe flow data from the literature is performed. Critical Reynolds numbers corresponding to the laminar-turbulent transition calculated from these data are found to agree with theoretically calculated values for the entire flow range studied. Similar agreement is found for the authors&apos; own data&apos; for flow of 10 slurries between parallel plates. The Bingham plastic model is shown to be a reliable representation of the flow of non-Newtonian slurries provided it is properly applied. If the Hedstrom number He = pD2 t0/?2 > 104, then the linear approximation method of Caldwell and Babbitt is invalid for pipe flow data obtained in systems of ordinary engineering interest, and the complete nonlinear form of the pipe flow Bingham plastic equation must be used in determining rheological parameters. INTRODUCTION Many materials of engineering interest must be handled and transported as slurries or suspensions of insoluble particulate matter in a Newtonian liquid. These suspensions frequently exhibit non-Newtonian rheological behavior which is reasonably well described by the simple Bingham plastic rheological equation1 Using this particular equation to describe the laminar flow characteristics of slurries was discussed at length by Caldwell and Babbitt2-4 who considered the flow of various clay slurries and sewage sludges. The model has since been used by many others.5-7 More recently the problem of predicting the laminar turbulent transition Reynolds number for Bingham plastic fluids has been treated8 for the case of flow in pipes. This paper points out errors which have existed in the analysis of Bingham plastic flow since the work of Caldwell and Babbitt2-4 and presents a reanalysis of the laminar turbulent transition calculatiod for Bingham plastic flow in pipes. In addition, new data obtained for flow of Bingham plastic slurries between parallel plates, both in laminar flow and in the laminar turbulent transition region, will be presented and compared with the theoretical analysis of laminar turbulent transition for flow between parallel plates. THEORETICAL ANALYSIS PIPE FLOW The mathematical analysisl-4 of laminar flow of a Bingham plastic fluid leads to the following equation. where q = <v>/R is a pseudoshear rate, rw is the wall shear stress Eo = r0/rw, r0 is the yield stress and 1 is the coefficient of rigidity or plastic viscosity from Eq. 1. Caldwell and Babbitt2-4 recognized that the quartic term in Eq. 2 was small compared to the other terms whenever 5, « 1, and that for large values of 7, a plot of Eq. 2 becomes linear. The slope of such a plot with rw as ordinate is 4? and the intercept is (4/3) ro. This approximation is illustrated schematically in Fig. 1. The shaded region between the true curve and the straight-line approximation near the origin represents the contribution of the quartic term. In principle, therefore,

By Carle R. Hayward

ATHOUGH there are signs of improvement in the lead industry, conditions are still far from what we have been accustomed to call normal. There has been little to stim¬ulate research and those responsible for the finances of the companies have been inclined to discourage expenditures except where need was urgent or the prospect for immediate returns bright. In spite of this fact, improvements have been developed here and there which will be available as business conditions become adjusted. No publicity is allowed at present. The rising price of silver has had a tendency to increase the production of lead from argentiferous ores but the greatest interest continues to be in the secondary field. Practically all lead plants situated near large centers of population are treating scrap materials, particularly battery plates, the quantity of which is increasing with the improvement in automobile sales.

Jan 1, 1936

By Lawrence A. Roe

The magnetic reflux classifier, which utilizes the combined effects of magnetic fields and a hindered settling classifier, is a new tool for determining the quantity and quality of middlings in fine-sized magnetite concentrates. Results are given for processing a typical taconite ore, and a sketch of the apparatus is included. IN examining magnetite ores and beneficiated products it often becomes necessary to make critical studies of the amount of grinding necessary to produce the desired degree of magnetite liberation. In the past this has been accomplished by laboratory heavy-liquid tests, which provide a method for selectively removing middling particles and free magnetite from various-sized fractions. Examination of the various products under the microscope results in fairly accurate determination of the degree of liberation. The method is quite efficient on sizes coarser than 325 mesh. Thus the heavy-liquid method of middling separation was satisfactory until the advent of present day magnetic taconite studies. When magnetite concentrates ranging from 70 to 100 pct —325 mesh are studied it becomes apparent that older methods of determining liberation size are not satisfactory and that there is need for a new method. For example, some of the low-grade magnetite ores of the Wisconsin and Michigan iron ranges require grinding to 100 pct —325 mesh to produce a magnetic concentrate containing less than 12 pct silica. Examination of concentrates from such ores often reveals that many of the middling particles consist of only very minor proportions of iron mineral. Thus it becomes important to be able to determine the degree of grinding necessary not only for complete liberation, but also for liberation of only 80, 85, or 90 pct of the total iron mineral content. Actually, complete liberation is never attained, but is often used to designate that degree of liberation necessary for production of high-grade concentrates. A rougher concentrate, produced after elimination of a coarse-sized tailing, can usually be subjected to a second grinding stage and concentrated into a higher grade product than could be produced from the same crude ore with one stage of grinding resulting in the same overall size reduction. This fact adds to the importance of being able to determine partial degrees of liberation on any magnetite ore. Standard laboratory methods such as heavy-liquid separation, microscopic grain counts, Davis tube magnetic separation, magnetic flocculation, classification, flotation, and others often are not applicable, or are prohibitive because of time requirements when large numbers of fine-sized magnetite samples are investigated. The Davis tube magnetic separator is an efficient tool to use in rejecting the non-magnetic mineral particles from an ore sample. The middlings discarded by the tube separator usually are so low in iron content that they can be considered relatively unimportant in liberation studies. This condition is caused by the extremely high flux density used in the Davis tube. This flux density ranges from four to eight times the flux density produced by most of the powerful commercial machines in use today. Thus the problem resolves itself into a search for a method of selectively removing middlings from Davis tube magnetic concentrates which will be both rapid and efficient. Those methods showing most promise in the development of a process for isolating middlings from extremely fine-sized magnetic concentrates were flotation and magnetic flocculation. The use of flotation to remove middlings from magnetic concentrates is reported in the literature.&apos;.&apos; The flotation process is effective in removing middlings from a magnetite concentrate, but physical entrapment of fine-sized free magnetite in the silica-bearing froth is an undesirable feature. The flotation method of removing middlings requires time, effort, and precise control of many variables, and does not meet the required degree of middling isolation. Magnetic Flocculation Magnetic flocculation has long been resorted to"-" in efforts to upgrade magnetite concentrates. One of the new magnetic taconite plants now under construction on the Mesabi Range includes magnetic flocculation in the flowsheet&apos; as an accessory process to remove high-silica middlings and free silica which has been mechanically entrapped in magnetite flocs. The use of magnetic flocculation as a laboratory method of making precise separation of middlings was further investigated, since it offered a rapid, simple method of accomplishing the desired result. Magnetic flocculation involves the subjection of a magnetic concentrate to a strong magnetic field, passing the concentrate in a highly flocculated condition to a hydroseparator or other classifiers of various types, and removing free silica and middlings as overflow products. In an attempt to utilize simple

Jan 1, 1954

The Manufacturer&apos;s Viewpoint A prominent manufacturer of mining &apos;machinery not long ago expressed himself as being confident that he was securing the best kind of publicity for his product through the advertising pages of the monthly Bulletin of the American Institute of Mining Engineers. Such an expression coming from such a man is highly gratifying; yet it is justifiable when the high quality of reader and subscriber is taken into consideration. In fact, the majority of those using our advertising pages feel the same. It is to be regretted, of course, that others catering to our field do not realize the means at their disposal for presenting the points of interest of their product to the mining man. The question has been asked, " Do your members read their Bulletin?" They not only read the editorial pages, but they "admit being up-to-date enough to peruse the advertising section to "see what is new." The next question the prospective advertiser asks is, " Will the Bulletin bring inquiries?" The answer to this question holds good for any publication having as subscribers those who have purchasing or recommending power-yes, if the article advertised is not a stock one, that has been before the public for any length of time. To secure inquiries on, say, a standard centrifugal pump or any other standard product, the features of which are well known, is a most difficult proposition. Yet, of course, some inquiries are secured, but mostly from those having use for the catalogue or trade literature for reference purposes. It is safe to say that the traceable returns from advertising in trade publications hardly, if at all, pay for the advertising. The real returns are intangible, and result from the constant publicity, and keeping ?everlastingly at it." Who can say what subconscious effect is taking place when an advertisement is "glanced at," to say nothing of the effect produced when the copy is attractive and interests the reader. Time after time it has been proved that sales have been secured as a result of an advertisement, yet no inquiry had been made directly traceable to advertising.

Jan 8, 1915

By F. E. Wood

This paper is written primarily as a discussion of Dr. W. P. Hase-man&apos;s paper on "A Theory of Well Spacing"&apos; and presents briefly the production records, and intensity and rate of development in a large portion of the two principal producing sands in the Salt Creek field, Wyoming. The study includes 1350 wells, 160,000,000 bbl. production, well spacings varying from two to seven wells per 40 acres and early and late development. The general conclusions to be derived from this study are: 1. It is impossible to formulate a mathematical rule to apply to well spacing in the Salt Creek field. 2. Each tract is a separate problem. 3. Tracts first drilled produce the most oil, with many exceptions. 4. Initial production is not a reliable index to the relationship between past, current, or future production. 5. Wells which have produced the most oil in the past are not necessarily yielding the greatest current production nor will they yield the greatest future production. In fact, wells which have yielded the greatest past production will, in at least one-half the cases, make less oil currently or in the future than wells which have produced a smaller quantity of oil in the past. 6. The following is a safe rule to apply in well spacing in the Salt Creek field: (a) If the drilling of an additional well on a tract results in a sustained increased production, with prospects of making a profit, the tract is not overdeveloped and additional wells might be drilled. (b) If the drilling of an additional well does not effect a sustained increase in the production of a tract, the tract is fully developed. Second Wall Creek Sand The Second Wall Creek sand, covering 20,000 producing acres, is the principal producing horizon in the Salt Creek field; 1610 wells are producing at this time from this sand. This paper deals with hut a portion of the entire field including 10,680 of the more productive acres,

Jan 1, 1930

By J. D. Edwards, C. S. Taylor, A. S. Russell

Solubilities and densities are reported for alumina hydrates in NaOH solutions under the conditions of the Bayer process employed to purify alumina for aluminum production. The equilibrium constants for reactions to form A102- accurately correlate the effects of NaOH concentration on the solubilities; the temperature coefficients of the equilibria lead to heats of solution of 7.34, 4.76, and 5.24 kcal for the a trihydrate, a monohydrate, and ß trihydrate, respectively. Moderate calcination does not change the solubility of the a trihydrate but increases that of the a monohydrate. At solution temperatures above 100°C, the trihydrates transform rapidly to a monohydrate. Hydro-thermally produced a monohydrate is the stable phase above 20°C. CORNERSTONE of the aluminum industry, the Bayer process for alumina production is based on the difference in solubility of hydrated alumina in NaOH solutions between 170" and 40°C. Solubilities and densities in this system were determined thirty years ago by M. Tosterudl under the direction of J. D. Edwards and C. S. Taylor. The solubility data, which still appear more concordant than those in the literature, are employed to sort out the complex equilibria in this system. The nomenclature for the alumina hydrates is that presented in The Aluminum Industry&apos; and more recently summarized in Alumina Properties.3 a trihydrate is the purified phase analogous to gibbsite, a monohydrate is similarly akin to boehmite, and ß trihydrate is sometimes known as bayerite. Literature Goudriaan4 reviewed the early literature on alumina in NaOH solutions and presented data on the solubility at 30°C of several forms. The gel precipitated from aluminum sulphate or chloride with ammonia and dried at 130" to 140°C had the highest solubility but was unstable, its solubility being cut to one-tenth on standing in NaOH. The solubility of the gel was decreased one-third on calcination at 300" to 400°C, while that of the gel transformed in NaOH at room temperature to a crystalline trihydrate was unchanged on calcination. The preparation produced by slow hydrolysis of sodium aluminate solution with CO, in the air gave solubilities in rough agreement with later values for a trihydrate. The solubility of this form was increased slightly by the calcination. Fricke and Jucaitis5 extended the work to 30" and 60°C with a trihydrate. They also gave solubilities for ß trihydrate (bayerite b), although the residue belonging to the left branch of the solubility curve corresponded to a trihydrate. The residues at high NaOH concentrations were mono and trisodium aluminates, the latter being 3Na2O . AL2O3 • 6H2O. Solubilities of a trihydrate at 95°C and of a monohydrate at 150" and 200 °C come from the work of Magarchak.6 a trihydrate transformed to a monohydrate above 95°C. A few measurements on the solubility at 25°C of an alumina trihydrate prepared by slow hydrolysis of NaAIO, solutions were presented by Sprauer and pearce.? Their analyses showed the monosodium aluminate to have the composition Na2O.Al2O3-2.5H2O.

Jan 1, 1956

By Dennis K. Mortensen

The Role of the Operator The ultimate objective of any installation is to be able to accomplish the useful work that it was originally designed for. The operator needs a tool that he can both operate effectively and maintain efficiently. The overall design and subsequent installation of a comminution circuit should be a marriage of good engineering practice and practicality. Since the operator must operate and maintain his equipment, his input into the design and installation is vital to its ultimate success. The design of a crushing or grinding circuit is dependent upon many factors including flowsheet design, equipment selection, physical layout, space restrictions, climatic restrictions and considerations for future expansion. The operator must live on a day-to-day basis with the results of the final design and installation. The most satisfactory operation will result when the operator has a major input into each of the criteria that are used to define the final design and installation. The operator referred to is not only the mining company or organization that is having the installation built for its specific use but, more specifically, the person or persons that will actually be responsible for its daily operation and maintenance. Future references to the "operator" will include those individuals with that daily reponsibility. The operator&apos;s input into the installation of the circuit is of equal importance to his input into the design. The engineering organization which puts together all of the various design drawings for circuit installation is generally restricted to trying to get all of the details onto a multitude of 24" x 36" two dimensional drawings with a few isometric drawings thrown in. It&apos;s almost impossible to get all of the details of a final installation onto all of the drawings, and field modifications are necessary to make everything fit properly. In a multilevel installation, such as a grinding or crushing circuit, it is difficult to envision space requirements to adequately operate and maintain the various pieces of equipment simply by looking at a set o£ drawings. For some designs it is helpful to build a scale model so that a more realistic view of what the installation will look like can be seen. The scale model allows the operator to make whatever changes in design are needed to operate and maintain his equipment most effi-

Jan 1, 1982

By E. O. Wagner, V. F. Parry, J. B. Goodman

C. P. HEINER*—If you take out 35 pct of the total weight of the coal in the form of moisture, would that be about what it was in the case of North Dakota lignites ? V. F. PARRY (authors&apos; reply)—That is about it. C. P. HEINER—That will be about a 35 pct loss and the final product will be about 11,000 Btu? V. F. PARRY—That is right. The heating value of the dried lignite is 10,000 to 11,000 Btu. C. P. HEINER—And the thought is not, then, to produce a commercial coal with that heavy loss, but to make other products—that is, synthetic fuel base, is that it? V. F. PARRY—The principal thought is to upgrade the coal, making it a more favorable raw material for industrial purposes, both for shipment and direct use. You see, the trouble in these lignites is that their moisture penalizes their

Jan 1, 1950

By Eugene H. Cowles

The German silver industry of the United States amounts in value to upwards of $6,000,000 or $8,000,000 annually. Several thousands of people earn a livelihood pursuing it, and the beautiful goods and articles manufactured from this time-honored and valued alloy are everywhere visible. German silver enters largely into our street signs, harness and house hardware, and all manner of table-ware, solid or plated. There is scarcely an hour in the day that German or nickel-silver is not before our eyes. The composition of this alloy is a very uncertain thing, and depends largely on the honesty of the manufacturer and the price the purchaser is willing to pay. It is composed of copper, zinc and nickel in varying proportions. The best varieties contain from 18 to 25 per cent. of nickel, and from 20 to 30 per cent. of zinc, the remainder being copper. The more expensive nickel-silver contains from 25 to 33 per cent. of nickel, and from 75 to 66 per cent. of copper. The nickel is used as a whitening element; it also strengthens the alloy and renders it harder and more non-corrodible than the brass made without it, of copper and zinc. Moreover, it reduces the odor emanating from brass, which is so disagreeable if it occurs about the dining-table. Of all troublesome alloys to handle in the foundry or rollingmill, German silver is the worst. It is unmanageable and refractory at every step in its transition from the crude elements into rods, sheets or wire. As a white-headed furnace-man recently said to the writer, in one of our large mills, " you can put eight crucibles into the fire, each containing exactly the same mixture of German silver, and when you take them out and pour them into slabs for rolling, seven will be a mass of scum or slag, or the stuff will swell up like rising bread and overflow the moulds, and be so full of blow-holes that it will look like a sponge. The eighth crucible will contain perfectly good metal. On remelting the next day, the bad stuff will, in nine chances out of ten, come out just as good metal as the eighth pot the day before, and under apparently the same conditions." With nickel at seventy or eighty cents per pound, German silver

Jan 1, 1890