Search Documents

By George Sears

UNTIL a comparatively few years ago, interest in tantalum was limited almost wholly to its scientific investigation, but its extreme resistance to the action of even the strong mineral acids, its great avidity for the common gases, hydrogen, oxygen and nitrogen, and its capacity for transforming alternating to direct current are winning for it a place in our industrial life. Tantalum is not attacked by any single acid except hydrofluoric, nor is it affected by solutions of alkalies. Aqua regia, which readily dissolves both platinum and gold, has no action on it. This resistance to the common corrosive agents is an outstanding property of tantalum and accounts for many of the applications to which it has been put. When heated, tantalum reacts readily with oxygen and nitrogen and absorbs large volumes of hydrogen, 740 volumes being taken up at a dull red heat. This capacity for absorbing gases is being utilized to an increasing extent in the manufacture of vacuum tubes, in which tantalum is used for the metal parts, especially for grid wire. It is said to be a superior metal for this purpose, particularly in power and sending tubes, because of its low secondary emission. The use of tantalum in the manufacture of electrodes, dishes, spatulas and other laboratory apparatus appears to be fairly steady. There has been some development in its use for dental instruments, surgical tools, pen points, hypodermic needles and acidproof pumps. Recently it has been used in the manufacture of spinnerets for the rayon industry, of nozzles for the manufacture of artificial casings for sausages and of lining for plant equipment.

Jan 1, 1930

By Henry P. Chandler

Tripoli is the general name for a number of fine-grained, lightweight, friable, minutely porous, forms of decomposed siliceous rock, probably derived from siliceous limestones or calcareous cherts. Tripoli is often confused, both in the trade and technical literature, with tripolite, a diatomaceous earth (diatomite), found in Tripoli, North Africa. A material found near Seneca, Mo., resembling tripolite was incorrectly termed "tripoli." This name has persisted and now has a definite physical and trade meaning. However, tripoli contains no diatoms, is of an entirely different origin, and has chemical and physical properties different from those of tripolite. There are two distinct types of tripoli in the United States; that from the Missouri-Oklahoma field and that from the Southern Illinois field. Commercially the term "tripoli" is applied to the material from the Missouri-Oklahoma field, while the material from the Southern Illinois area is often referred to as "amorphous" or "soft" silica. Material similar to the Missouri-Oklahoma tripoli, but finer grained, occurs in northwestern Arkansas. In its Minerals Yearbook the Federal Bureau of Mines groups statistically under "natural silica abrasives," tripoli from these producing areas and rottenstone from Pennsylvania. The justification for this grouping is the similarity of use. Composition and Physical Properties Commercial tripoli contains 97 to 99 pet SiO2. The remainder is mostly alumina, iron, lime, soda, and potash, some of which may impart desirable physical properties to the material. Variations in the chemical composition of tripoli are not as important as its physical characteristics. The color of tripoli varies from white to cream, brown, rose, and red, the variations from white being the result of iron deposited from percolating surface waters. The commercial varieties of tripoli mined in the Missouri-Oklahoma area are designated as cream and rose. Other physical properties of the tripoli from this area are: Free quartz, less than 0.5 pct; oil absorption, 50.71 to 53.14 pct; water absorption of the crude tripoli, about 38 pct, and of prepared material, about 52 pct; fracture, uneven to conchoidal; specific gravity, 2.15 to 2.62; weight per cubic foot crude, 35 lb, ground, 55 lb; fusion point, 3,225° to 3,300°F; and refractive index, 1.54. Tripoli occupies about 1 cu yd to the short ton in place and about 1.5 cu yd when broken. Packed for shipment, the powdered material occupies about 33 cu ft to the ton. Its value and usefulness depend primarily on a low content of crystalline silica, size of the natural particles, absorption, and color. Some beds in the Missouri-Oklahoma area are of sufficiently compact material that large, fairly strong blocks may be removed. These find a market as filter blocks and have been used for building material. In the Southern Illinois field the color of the material is the important physical property; pure white is preferred. The rottenstone mined in Pennsylvania is of higher density and lower in silica content than the various types of tripoli. Its composition approximates 60 pct silica, 18 pct alumina, 9 pct iron oxide, 8 pct alkalies, with small amounts of lime and magnesia. The material apparently is a ferruginous and siliceous shale, having properties rendering it suitable as an abrasive or as a filter for paint, rubber, and plastics.

Jan 1, 1960

By W. N. Best

THIS paper is not intended as a scientific discussion of the combustion of oil but is written from, the standpoint of an operator who has the experience and qualifications necessary to guide others in producing the most economic results in the use of liquid fuels. Oil, in this paper, usually, means petroleum or its products but incidental reference is made to other liquid and gaseous fuels, so that the term may be considered, as referring to all liquid and gaseous hydrocarbons in comparison with solid fuels, as coal and. wood. However, only a few of the principal factors in the use of oil as a fuel can be given. The present, and prospective, high price of coal is causing users of fuel to renew inquiry as to the merits of other forms of fuel for industrial purposes. Crude oil (petroleum) is proving to be one of the world's most valuable mineral resources. The recent discovery that oil underlies a considerable area of the United States, Mexico, and other parts of the world to a greater extent than was formerly believed and the large production of some of the wells in these areas shows the probable quantity of fuel oil that may now be available. Through the energy of Lord Cowdrey, who was one of the pioneers of the oil industry in Mexico, oil has been discovered in England; some prominent geologists believe that it may be found yet, in quantity, in Great Britain. For years, oil has been known to be of great value in the manufacture of metals. It has proved incomparable in forge shops, steel foundries, heat-treating furnace s, and wherever accuracy of temperatures is essential, or where a maximum output is desired as well as quality of metal. In some types of equipment, the output produced with oil as fuel is double that obtained with coal and, at a reduction of 50 per cent, in the cost of the fuel. For example, in drop-forging plants, the metal is always waiting for the man when oil is used as fuel, whereas with coal, the man must wait for the metal to become sufficiently heated.

Jan 8, 1920

By Sherwin Kelly

THE need for geophysicists to adopt a uniform mode of expressing the electrical resistivity of geological formations has been stressed by Dr. A. S. Eve.1 The present paper is to emphasize the point he raised, to bring the weight of disinterested authority to bear on the matter, and to urge the adoption henceforth, save in exceptional cases, of a standard expression for resistivity; all in the hope that the needed reform will thus actually be brought about. The general definition of the resistivity of a material is the resistance in ohms between two opposite faces of a unit cube of that, material. No account need be taken here of the cases in which the unit volume is not a cube, and the units of length and cross-section are different, encountered principally when dealing with metallic conductors such as wires. The idea of the resistance of a unit volume of earth or rock has found expres-sion in geophysical literature in a number of forms and with a variety of units. Fortunately, the metric system has been adhered to in most cases, so ordinarily the meter or the centimeter, usually the latter, has been the measure chosen. The resistivity is then the resistance of a cube of the given rock, or soil, one centimeter on, an edge. This is far from always being the same thing, however, as the resistance of a cubic centimeter. A long thin wire could contain a cubic centimeter and have a high resistance, whereas the same volume formed into a flat plate would have an entirely different, and quite low, resistance between faces. Con-sequently, it is not proper to express resistivity in ohms per cubic centi-meter, inch, etc., as has been done occasionally by .some writers. In an effort to emphasize the idea of cubic volume, some geophysicists, the writer among them, have used the phrase, ohms per centimeter cubed. This is a graphic way of picturing the measure, but is not in favor among highly qualified authorities. In this connection, an appeal was made to the U. S. Bureau of Standards for advice, and the Director, George K. Burgess, kindly replied in detail as to the practice adopted by his Bureau: ." . .' such expressions as ohms per centimeter cubed' or any similar expressions are objectionable, because they certainly carry the implica-tion that the resistivity is found by dividing ohms resistance by the volume in cubic centimeters." Actually, of course, resistivity is found

Jan 1, 1932

By Jean Howard, E. V. Walker

ManY papers have been published during the last few years on the formation of cube texture in 3 1/4 pct Si-Fe, e.g., those of Assmus, Detert, Dunn, and Walter.1,5 All are concerned with the formation of the texture by a process involving secondary re-crystallization and the relative surface energies of (100) and other planes under certain conditions of annealing. The authors have found that cube texture can also be produced by heavily cold rolling strip in which the cube-on-edge texture has first been formed. Cube texture develops on annealing, but in this case it is not accompanied by secondary recrystallization. The starting material is a sintered compact, the preparation of which has been described elsewhere. Using a conventional processing schedule employed for producing commercial silicon-iron with the cube-on-edge texture, the sintered compact is cold rolled to such a thickness that, after annealing in pure hydrogen for 24 hr at 1350'~ to produce the cube-on-edge texture, the final thickness required can be obtained by giving a further cold reduction of 85 pct. Cube texture is developed by annealing at -900~~ in pure hydrogen: it has been produced in strip up to 0.024 in. thick. The microstructure of the strip consists of a mass of small primary grains within the boundaries of the much larger secondary grains which ex- hibited cube-on-edge texture before the final cold roll. If the strip is annealed at -1000 after the 85pct reduction, secondary recrystallization begins to take place, provided a strong cube texture is present. On raising the temperature more secondaries grow, complete secondary recrystallization being obtained on annealing at -1150'. From this it is concluded that the secondary crystals are produced by the texture inhibition mechanism: they show (110) and (111) planes in the surface of the strip, the former being the more numerous. It has been observed that the more perfect is the (110) [001] texture prior to cold rolling by 85 pct, the further from the ideal is the (100) [oo].] texture. A similar treatment applied to high quality commercial grain-oriented silicon-iron strip failed to produce cube texture. The tilt and rotation of the [loo] from the rolling direction was less than 10deg, but (to within a few degrees) the planes (130), (450) and (210) lay in the surface of the strip. Acknowledgment is made to the Engineer-in-Chief of the British Post Office for permission to use the information contained in this note.

Jan 1, 1962

H. G. KNOX,* Norfolk, Va. (written discussion?).-There is one subject that Mr. Hobart seems to have inadvertently omitted from his very valuable paper, and that is corrosion. The shipbuilder, perhaps more than anyone else, has constantly to guard against it, our chief reliance being paint and galvanizing, where practicable. The corrodibility of a welded. joint is salt water must be determined before deciding whether this type of construction is to supersede riveting. At the present time, this question cannot be answered, although considerable work has been started in an attempt to arrive at a conclusion. The British Admiralty and several British shipbuilders have studied it extensively. Their experiments and conclusions have been very carefully followed and reported in this country by Naval Constructor Goodall of the British Navy. To date, these show that no undue fear need be felt from corrosion. At the Norfolk Navy Yard a series of plates welded with various electrodes were submerged in dilute sulfuric acid, such as is used in cleaning prior to galvanizing. While this test may not be conclusive in any quantitative way, it does show a marked difference in the corrodibility of welds made with different electrodes tinder different conditions. To thaw any conclusions from this accelerated this accelerated test would be, however, ill advised. In riveted joints, the exposed heads and points of the rivets always show the greatest tendency to corrode. This is clue to two reasons: first, as they are raised above the surrounding surface the paint is more susceptible to abrasion; and, second, electrolytic action is set up between rivet and plate. These same reasons lead us to expect a tendency of the welded joint to corrode. Various methods have been suggested for decreasing the probable inherent corrodibility of the weld, in addition to the customary coat of paint. These generally embody the introduction of alloys, principally copper; into the electrode material. Plating the electrode with copper is not effective in that the deposited copper segregates in the weld and actually increases the electrolytic action. As far as is known, no extensive test on the so-called copper-bearing alloy steels, which might be made up into electrodes, has been carried out, but when obtainable, electrodes of this alloy will be subjected to service tests.

Jan 6, 1919

By Raymond B. Ladoo

TIIe milling of talc, as is the case with many non-metallic minerals, until recently, has not received adequate technical consideration, for the talc industry has become of importance only within the last decade. At first, talc was used only in the massive form, for foot warmers, griddles, and so on, and milling methods were unnecessary. As the demand for ground talc increased, producers adopted the machinery used in the milling of flour; in fact, many talc mills were rebuilt flour mills. Improvement has been slow, but today several types of grinding and separating machinery are in use; many of them, however, are still inadequate and inefficient. To determine the best methods of milling talc, it is necessary to understand the essential properties a talc must possess to fit it for a particular use. For toilet purposes, whiteness, freedom from lime and grit, fineness of grain, and good "slip" are essential. As a paper filler or coating, the talc must be white, uniform, and fine grained, have a good slip, and be free from grit and iron; freedom from lime is a disputed point. Fibrous talc is supposed to be superior to massive on account of the interlocking of grains in the paper, thus increasing its strength; this point, though, is in doubt. In general, talc for the paper industry need not be of as high quality or as fine grained as that used for toilet purposes. Talc is usually bought by sample, for which reason it is difficult to state the essential properties for use in paint, rubber, roofing, and so on. The adoption of standard screen tests and standard grades by producers is necessary before an accurate basis for manufacturing or selling standards can be established. Off-color talcs might be utilized, as in Germany and Austria, by the establishment of standard grades of colored talcs. The machinery to be used depends on whether the talc is fibrous, foliated, or massive; hard or soft; of uniform or variable grade; pure or impure. In some cases, it is possible to change the mining practice or to utilize different sections of the deposit in order to vary some of these factors, but in many cases these factors are fixed, so the milling must be designed to suit the conditions.

Jan 1, 1922

By J. Peperakis

Coal mine bumps are normally associated with pillar mining under moderate or deep cover. Severe bumps at Sunnyside, however, have not been confined to pillar lines. Many have occurred in virgin development and in localities a long way from active pillar workings. As early as 1918 bumps in virgin territory were attributed to the faulted structure in the Sunnyside area.' Sunnyside is an old property, mined for more than 60 years. Both man-made and natural conditions contribute greatly to bump occurrences, and loss of life and great destruction of workings have resulted from some unusual bumps in recent years. Before Kaiser Steel acquired the Sunnyside Mines in 1950, about 21 million tons of coal had been extracted. Large areas had been worked out and equally large areas first-mined. As demand for coking coal gradually diminished, extensive blocks were shut down, and during the low production period of the 1930's mining on a very limited scale was confined to a section of the property close to the coal tipple. Following purchase of the property Kaiser Steel developed the mines into a fully modernized operation. The worked out and first mined areas covered about four square miles extending five miles along the strike and up to one and a half miles down dip from the outcrop. The sections with favorable mining conditions and clean coal had been largely extracted under the selective mining system imposed by economic conditions and the lack of cleaning plant facilities. Large reserves remained on the fringes of the worked out sections and in areas under deep cover and difficult roof. There were also considerable reserves in first-mined areas. In recent years much of Sunnyside's daily output of 7000 to 8000 tons has been derived from the partially mined localities. Many bumps have occurred when pillars have been pulled within the first-mined areas and on the fringes. The bumps have been associated with retreating pillar lines backing up against old workings and pillar lines in old first-mined areas backing up against highly stressed oversized barrier pillars surrounded by smaller pillars. In some parts of the property the upper Sunnyside seam was extensively worked in the past, and sizable areas of old works overlie the present lower seam workings. Abutment pressures from barrier pillars and pillar remnants are transmitted to the lower seam, contributing to bumps and squeeze conditions. Cover: The terrain is exceedingly rough, and cover varies considerably over relatively short horizontal distances. For example, at No. 1 mine the 2000-ft cover line is ony 2700 ft from the coal outcrop, and at No. 2 mine the cover over the main hoisting slope increases from 1000 to 2000 ft in a horizontal span of 1200 ft. Cover over the present mining sections ranges from several hundred feet in the valleys to 2500 ft under the crest of the divides. A short distance ahead of Sunnyside's deepest development down dip the cover reaches 3000 ft or more.

Jan 1, 1959

FRANCIS B. SILSBE,* Washington, D. C. (written discussion?). ?This paper is an interesting example of the -solution by the methods of metallography of what seemed at first a purely chemical problem. The authors have shown: in detail, how the well-known corrosion of spark-plug terminals is due to the dropping out of the individual crystals of the metal as it becomes surrounded by an oxide film. This corrosion is usually quite slow but in special cases may become a serious factor in limiting the life of spark plugs. There still remains the problem for the metallurgist to produce a material that will be entirely free from, this trouble. One of the most startling results of the work is. the demonstration that it affords of the deleterious effect of a mechanical stress continuously applied to material that is at the same time subject to adverse chemical or thermal conditions. The particular style of spark plug shown in the illustration, and in which serious trouble was caused by this corrosion, has the side terminals fastened at both ends and the method of assem-bling is such that a considerable initial tension is applied to the wire. It is without doubt this superimposed tension that causes the inter-crystal-line network to line up, as it were, into a few continuous and deeply penetrating transverse fissures instead of forming a great number of shallow surface cracks. This result is clearly shown both in the case of

Jan 11, 1919

By C. H. North, L. E. Lynd, W. W. Anderson, H. Sicurdson

D. R. Grantham (Institute of Mining and Metallurgy, London, England)—This paper is a very valuable contribution to our knowledge of ilmenite and its alteration products. Two aspects are not treated in the paper and further information would be valuable. How far are the alteration processes described influenced by the original composition of the ilmenite? The word gangue is used but it is not clear whether this refers to other chemical constituents in the ilmenite, e.g., magnesia, or to other minerals loose or in composite grains. Has the work described been related to specific gravities? Pure ilmenite is stated to have a specific gravity of 4.79. Some varieties range up to over 5.0, while high magnesic varieties have a specific gravity ranging to below 4.2. Alteration to hematite might lower the specific gravity and a porous texture due to the removal of iron and the formation of rutile might also lower it. As specific gravity is a quick method which often gives an approximate indication of composition, data on the above would be valuable. L. E. Lynd (authors' reply)—Because of the way in which beach sand deposits were formed, it is impossible to tell exactly what the original composition of the parent ilmenites might have been. Information on the influence of original composition on the alteration processes must be derived from other sources, perhaps by comparing the alteration products formed from ilmenite in place in a variety of rock deposits, where parent ilmenite and its alteration product can be recognized. No information of this type has yet been brought to our attention. The material referred to as gangue includes all constituents other than oxides of titanium and iron. Nearly all of this was present as separate grains of garnet, augite, hornblende, quartz, feldspar, spinel, or other gangue minerals. Inclusions of gangue minerals within ore grains were rare, and we believe there is little MgO (1 pct or less) or other impurity actually held in the ilmenite structure in any of the concentrates studied. No specific gravity measurements were made on the samples studied. However, the suggestion that alteration involving loss of iron would lower the specific gravity is a very reasonable one, and is in accord with the findings of Creitz and McVay (Ref. 9 of our paper) who reported two magnetic opaque fractions from Trail Ridge, Fla., to have the following specific gravities and pompositions: The specific gravity of this porous, high TiO² alteration product of ilmenite is closer to that of rutile (4.25) than to that of ilmenite. Due to the porosity, it may even be less dense than rutile, although lower in TiO² and higher in iron.

Jan 1, 1955

The plan recently started for the organization of a Division of Re-search and Statistics in the American Petroleum Institute will probably shortly be consummated. It is proposed to expend $500,000 annually for this research work. The organization's work, as now outlined, pro-vides for a Technical Director, who is to be in general charge of all the work. He is to be assisted by Consulting Technical Experts, who are to be distinguished specialists in the industry and are to serve without pay. In addition, there is to be an advisory committee made up of one representative from the Bureau of Standards, Bureau of Mines, Geo-logical Survey, American Institute of Mining and Metallurgical Engi-neers, Society of Automotive Engineers, National Automobile Chamber, of Commerce, American Society for Testing Materials, American Chem-ical Society, and the National Research Council. This committee is to meet regularly to discuss the problems of the petroleum industry. An engineer and chief economist are to assist the Director.- The econ-omist is to be in charge of statistics, economic phases of the industry, and publicity. It is the intention to centralize in the Institute all infor-mation that may be required by the States or Federal Government, which would be of value to members of the Institute. This includes prices of crude oil, refined products, and natural gas. The engineer of the division is to coordinate the research work to be undertaken by, the subdivisions of production, chemical engineering, utilization, and special research. Systematic study is to be made of the

Jan 12, 1919

By C. A. Hope, H. B. Wishart

THE number and severity of surface imperfections on rolled slabs, assuming the reception of uniformly good quality heats from the open hearths, depend upon a number of conditions associated with heating and rolling of steel in the primary mills. While there are other elements that have an effect on surface quality, rather than make this paper too lengthy the discussion of mill processing variables will be limited to three factors in order to illustrate their effect on slab surface quality: 1—amount of reduction between ingot and slab, 2—slab finishing temperatures, and 3—influence of roll changes. Measurement of the percentage of surface removed by scarfing on the flat surfaces of the slabs was used for evaluating quality in this study. A study of this nature must be made on slabs that are inspected and conditioned under uniform conditions and standards. In order to be certain that steel of the best possible steelmaking quality was received at the rolling mills, a low carbon deep drawing grade of rimmed steel, made for sheet mill application and manufactured under carefully controlled open hearth practices, was selected. Use of this particular steel thereby reduced the steel quality factor as a possible source of variation. The measure of slab surface quality is the amount of surface removed by scarfing during yard conditioning and is expressed as percentage of surface removal. This percentage was estimated by experienced personnel to uniform standards and it should be noted that these percentage figures are representative only for the grade selected and under the rigid inspection standards to which the slabs were subjected. Surface removal is a matter of concern because the imperfections, if undetected, often are the cause of poor surface quality in the finished product and their removal, by conditioning, add to the total plant costs. The data was collected at various times over a period of six months and, with normal weekly fluctuation in the level of quality, it is to be expected that for any period of sampling there will be some variation in the plotted results. The type of defect that is responsible for most slab conditioning at Gary Steel Works is a light angular surface break. This defect is usually interconnected to form large defective areas and occurs mainly on the bottom half of the slab on both sides. This type of defect is illustrated in Fig. 1, showing a bottom portion of a slab; while a close-up of an area of the same slab where the surface breaks were found is given in Fig. 2. The large dark areas are heat patterns, results of hot stacking and cooling. Independent of these light breaks, but sometimes associated with them, are larger and deeper isolated breaks. However, most of the surface removal occurs from conditioning the large areas of small breaks. There are also occasional scabs of varying degrees of severity but these are relatively infrequent. The slabs are generally free of rolled-in scale. Ingot to Slab Reduction vs Quality Some ten years ago at Gary Steel Works, the minimum slab ingot thickness was 30 in. Subsequent operating and other quality features indicated the desirability of using an ingot of reduced thickness with the result that a series of molds that would produce a 22 in. thick ingot with various widths was adopted as standard. A minimum number of the thicker mold sets are still used. From the standpoint of quality difficulties from pipe and segregation, the smaller ingots are an improvement. From a quality surface viewpoint, the slab product from the thin molds requires approximately twice the surface removal as the slab product from the thick molds. This is shown in Fig. 3 where the percentage of surface removal is plotted against slab product rolled from

Jan 1, 1956

By H. G. Botset

ANY information that will increase the accuracy of our knowledge of the conditions prevailing in petroleum reservoirs should be of direct value in the determination of the proper operating technique as well as in the estimation of reserves and of ultimate production. The obvious method of obtaining this information is by studying a sample of the reservoir rock and its contents. In any such study, the problem of primary importance and maximum difficulty is that of getting the core to the surface in such a manner that its original fluid content is undis-turbed, which has so far proved to be an impossible task. Though it might be rash to say this will never be done, it is certainly safe to assume that a method for the recovery of a core at the surface in its undisturbed original state may not be developed in the immediate future, and certainly will not be forthcoming without a great deal of costly experimentation. Therefore any information that may be obtained that will help to correlate the state of a core (its fluid saturation) at the surface with its condition at the time it was drilled should be of value to the petroleum industry. The experiments described in this paper were undertaken with the purpose of determining, if possible, any relationship that might exist between the saturation of a core at the surface and its original fluid content. No consideration has been given to the question of contamina-tion by penetration of drilling water, since this problem has been exten-sively studied by other investigators. 1-3 Furthermore, it was regarded as being outside the scope of the present experiments, which were con-cerned only with the effect of pressure reduction upon the liquid content of cores. In an experimental study of this sort involving a large number of variables, accurate control of all factors is very important. The essen-tial and obvious procedure is to vary systematically one factor or condi-tion while keeping all the others constant, which necessarily involves a rather protracted and sometimes tedious experimental program.

Jan 1, 1939

By Magnus Troilius

The method of using the bromine process of determining sulphur in steel, described below, is in successful use at the Midvale Steel Works. Ten grams of drillings are weighed out and put into the 1/2-liter flask A, with long neck. The flask is connected with a wide glass tube C', which, in its turn, is connected with the absorption bulbs B, containing HCI, 1.12 specific gravity, and ahout 5 C.C. of bromine. The wide tnbe C causes the vapor to condense and flow back into the flask A during boiling. The bulbs B connect with a long glass tnbe, which may be made to carry off the bromine fumes through a hole in a window, or, better still, through a flue with powerful draught. The connections being made, 100 C.C. of boiling water are run in through the thistle tube T. The air is thus completely driven out of the flask. 100 C.C. of HC1 (about 1.19 specific gravity) are then run in. When the gas begins to run rattler slowly through B, heat is applied until boiling gradually ensues. The steel being completely dissolved, the apparatus is disconnected, and the contents of B rinsed out into a beaker of 100 C.C. capacity, into which a few C.C. of a concentrated solution of BaCI, have been previously introduced. Heat is then applied (best by means of the hot iron plate) until the bromine is completely driven off and the BaSO, has settled nicely to the bottom. The BaSO4, is then filtered off on a small

Jan 1, 1884

By Michael Bradbury

INTRODUCTION A major change in financing exports in recent years has been the decreased importance of subsidized export credits, following the commitment of the OECD countries to eliminate the subsidy element. Subsidized export credit rates are now often more expensive than market rates as the financing for exporters has decreased in volume and importance. The forfait market, in recognition of this decreasing importance, provides a rapidly expanding source of nonrecource finance for exporters. The following is a step by step guide to what it is, how it works, its benefits and problems. WHAT IS FORFAITING? Forfaiting is not new. It has been used in Europe for about 25 years to provide export finance for both capital goods and commodities without recourse to the exporter. Although long the preserve of exporters in Germany, and more lately Italy, forfaiting is now used increasingly by exporters in Great Britain, the United States, Canada and Scandinavia. It is a fairly simple operation with easy straight-forward documentation. The transaction involves the purchase by the forfaiting bank of a bill of exchange or a series of bills without recourse to the exporter. These bills will have been drawn by the exporter, accepted by the importer, and will usually bear the unconditional guarantee of the importer's bank. They are normally drawn payable at intervals during the credit period agreed between importer and exporter and are purchased at a discount by the forfaiter. The exporter thus obtains his cash payment and the importer receives his credit period. The forfaiter collects the amount of the bills as they mature directly from the importer. Credit periods vary, depending upon the type of goods and the country and commercial risk of the importer. The period is generally between one and five years with six monthly maturities. The usual forfait currencies are US dollars. Deutschmarks and Swiss francs and others, such as sterling, French francs, and the Scandinavian currencies are being used more frequently. CHOOSING FORFAITING Most types of financing require the continued involvement of the exporter in the financial side of the transaction during the credit period. Forfaiting has certain comparative advantages. In particular, it is possible to forfait 100 percent of the risk without recourse to the exporter, unlike government sponsored export finance schemes, where some retention of the risk by the exporter is required. In addition, exports from country sources do not present problems and forfaiting can also cover trade within the EEC. Other benefits for the exporter are: (a) The exporter's balance sheet is improved; debts are turned into cash thus improving the liquidity of the company and enhancing its cash flow. And there are no contingent liabilities for bills of exchange. (b) If the sales contract is in a foreign currency forfaiting removes the risk to the exporter of adverse movements in foreign exchange during the credit period. (c) Fluctuations in interest rates during the credit period can be ignored since in forfaiting the transaction is usually done on fixed interest rate terms on a discount basis. (d) The political and transfer risks are taken by the forfaiter. (e) The commercial risk is taken by the forfaiter. (f) The costs of administration and collection etc. during the credit period are removed.

Jan 1, 1985

"The earth is the Lord's and the fullness thereof." Science knows no national boundaries, knows no country. These views might be taken as premises for a discussion of the development of the mineral resources of the world. Yet how far man is removed from such broadminded ideals! In this day of jealousy and dread, of political machinations and statesmen's maneuverings, of rantings and crass ravings against fellow-beings, man's attitudes towards God's gifts are but the measure of the smallness of man. That the exploitation of mineral wealth should be for the common good, none will deny, but what is meant by "common"? Is it for the common good of The Pennsylvania State College, Pennsylvania, the United States of America, or the world? If man is big enough and honest enough to state categorically that by "common," as used in the context above, is meant that the utilization of the mineral wealth should be for the mutual benefit of all mankind, and that all concerned strive to see that such a viewpoint is executed, then there is brighter hope for the future. It is to be hoped that the world may have at least a few years or possibly a generation of peace. What can be done in these years to work towards the ultimate goal of human improvement? The work of statesmen in the drafting of international agreements and the easing of small frictions which appear between nations, as they

Jan 1, 1950

By W. T. Stuart

THE increased demand for iron ore has necessitated a re-examination of ore-bearing lands on which the presence of water previously has indicated hazardous and expensive operating conditions. In view of the importance of iron ore production to the national economy and defense, the Ground Water Branch of the U. S. Geological Survey, in cooperation with the state of Michigan, began a study of mine drainage in the Iron River district in 1945, and later extended the work to the Marquette district. The purpose of these studies was to define the principles involved in the movement of surface and ground water toward the mined areas, with the hope that the information obtained in the research would lead to the development of methods of water control and to a reduction in the total mining costs. Not only are the direct costs of drainage increasing, but also the indirect operational costs of working a wet mine are becoming a larger proportion of the total mining costs. For some wet mines the direct costs of pumping and drainage may range from 35 to 40Ø per ton of ore produced, but the indirect costs due to handling wet ore and controlling the water may be five to ten times this amount. The methods of study were formulated as the work progressed, and inasmuch as they were the first large-scale studies of their kind, they should serve as a guide for the solution of similar problems in other mining areas. The Iron River district was chosen for a pilot study because in this district the longest records of mine pumpage and water-level observations were available, including, as they do, the records for the Homer mine of the M. A. Hanna Co., where pumping from surface wells began in 1930. The results of the first investigation by the Michigan Department of Conservation have already appeared." The first section of the report on a similar study of the Marquette district, which was started in 1948, will be published this year. Methods of Study In an effort to reduce the flow of water into the mine workings in the Iron River district, about 4500 gpm was pumped from the bedrock being mined and about 9000 gpm from the glacial overburden. In the Marquette district in the vicinity of Ishpeming and Negaunee, about 5000 gprn was pumped from the bedrock and about 4000 gpm was pumped from the glacial overburden. Where the water was pumped only from the bedrock, the rate of pumping ranged from a few hundred gallons per minute in the dry mines to many hundred gallons per minute in the wet mines. In each district, pumping from the overburden was localized on a few properties where costly pumping installations had been made and the expenditures for power had been large. In each district a comprehensive ground-water investigation was made of the whole area, involving the collection and interpretation of all the available data bearing on the source and quantity of water to be controlled. Although it is not the purpose of this paper to discuss the methods of making a ground-water investigation, it should be pointed out that a drainage study follows a pattern of engineering analysis that determines the occurrence, source, movement, disposal, and quantities of water involved. The investigation in the iron-mining districts of Michigan began with the construction of a map of the buried bedrock topography. Because the ground-water reservoirs occupy the low points in the bedrock basins, this map gives information concerning their areal extent, depth, shape, and degree of interconnection. The depth to water in the drillholes and wells indicates the altitude to which the ground-water reservoirs are filled, and the logs of the material penetrated in the drillholes and wells indicate the general character of the materials filling the reservoir. The slope of the ground-water surface indicates the direction of flow through the reservoir, the water movement being from the points of higher altitude to points of lower altitude. By analysis of the rise and fall of the ground-water levels in response to additions of water through recharge and to changes in the rate of discharge through pumped wells, estimates of the total quantity of water in storage and of the rate of flow through the reservoir

Jan 1, 1952

By Edward H. Robie

SHOULD the name of our Institute be changed? Perhaps one should say, should it again be changed, for until 1919 the name was the American Institute of Mining Engineers. When the American Institute of Metals joined our ranks we became the American Institute of Mining and Metallurgical Engineers. To make it a full mouthful, and strictly legal, one should add the word "Incorporated." At the June meeting of the Board of Directors it was suggested that this name was not a particularly happy one, especially so far as members of the Petroleum Branch, comprising a quarter of our membership, were concerned-not particularly appropriate as the name for the professional society for petroleum engineers. Apart from the petroleum group, the present name is felt by some not to be sufficiently comprehensive. Most geologists and many metallurgists, ceramists, and fuel technologists, for instance, are not engineers. They could never qualify as registered professional engineers under the licensing laws and yet they are valued and fully qualified Members of the AIME. The Directors, at the June meeting, thought the idea of a change in name should be presented to the membership for discussion, and suggested this column as the avenue of approach. Nine years ago Dean Steidle, of Penn State, recommended among other things that the name of the Institute be changed to "American Institute of Mineral Technologists and Engineers." In an editorial in Mining and Metallurgy in January 1944 objection was offered to this name but "American Institute of Mineral Engineers" was suggested. A special committee appointed by the Board to review Dean Steidle's suggestions (W. B. Heroy was Chairman) suggested that if the AIME were starting from scratch, the American Institute of Mineral Engineers might be a preferred name. It was not thought that the change suggested by Dean Steidle was one of major importance, and the comment was made that "the present name has gained prestige through many years and is cherished by our membership. An important element of 'good will' is attached to it and some of this would be unquestionably sacrificed by any change." In M&M for February 1945, Oliver C. Ralston went into the derivation of the terms mineralogy and metallurgy, and pointed out that both Mining and Metallurgical mean "digging," etymologically. He went on to show, with tongue in cheek, that if we want a short and all-inclusive name it should be American Institute of Geo-urgists, or, for euphony, Geolurgists. Oliver's brilliant development seems to have been received with speechless wonder! Should a decision ever be made to change the name, we think most members will agree that the American Institute of Mineral Engineers is to be preferred over anything yet suggested. "Mineral" has become, through usage, a much broader term than is indicated in the dictionary. Webster states that a mineral, in the true sense, must be inorganic, but Murray's Oxford English Dictionary seems more liberal, defining "mineral" as "any substance which is obtained by mining; a product of the bowels of the earth;" and "mineral oil" as any oil of mineral origin, as petroleum or shale oil. Certainly "the mineral industry" is ordinarily taken to include those activities based upon processing all the metallic and nonmetallic ores and deposits found in the ground, including the fuels. One advantage of this title is that the familiar abbreviation, "AIME" need not be changed. The advisability of maintaining a well-known abbreviation is evident, and was recognized, for instance, when the Committee for Industrial Organization became the Congress of Industrial Organizations some years ago. But if the petroleum engineers are the ones to be chiefly considered in revising the name of the Institute, it is by no means certain that they would feel that they are much more adequately recognized in a group of Mineral Engineers than in a society of Mining and Metallurgical Engineers. 'And then there remain, of course, the considerable number of professional members of the Institute who are not engineers at all. Comment from readers is invited.

Jan 1, 1952

By Leon Y. Sadler, E. K. Landis

Froth flotation has been described by several authors" as being analogous to a first-order rate process. Although a few investigators"," have found orders other than one fit their data best, the rate is described most often by the first-order equation, [ ] where r is rate of disappearance of floatable mineral by flotation, C(t) is concentration of floatable mineral in the cell, t is time, and k is first-order flotation rate constant. One of the difficulties in using this rate equation to develop a mathematical description of an actual flotation process is the determination of a suitable value of the constant k. The value of k, which reflects the floatability of the floatable mineral, is dependent on the hydrodynamic conditions in the cell, type and concentration of flotation reagents used, pulp density, and pH, method of froth removal, aeration rate, particle characteristics, and many other factors. Therefore, it is reasonable to expect that each particle of floatable material has a distinct value of k and that a unique distribution of k values exists for given feed and cell conditions. This has been observed and discussed by several investigators, and mathematical descriptions of the batch cell and steady-state continuous cell with distributed flotation rate constant have been developed." The mathematical description in the form of a transfer function of the continuous or flow cell under unsteady-state conditions with a distributed flotation rate constant has not been presented in the literature. The purpose of this note is to make such a presentation. The basic features of the perfectly mixed continuous

Jan 1, 1974

By R. T. DeHoff

A general method for determining the geometric properties of structures composed of particles which are all the same shape and size is presented. The application of the method requires a knowledge of' the qualitative shape of the particles in the structure, ad a maximum of three simple counting measurenzents, which are made on a representative plane section taken through the structure. It is also shown that the number of different kinds of measurements necessary JOY the complete description of the structure can be decreased if some independent information about individual particles is available. The geometric properties that can be determined quantitatiz~ely from counting measurements for susch structures are size, shape, number, surface area, vlolume, ad such extensive properties as volume Mction and surface area per unit volume. THE simplest kinds of measurements that may be made on a metallographic section are counting measurements. There are three such simple counting measurements, which are determined by sampling the microstructure with a point, a line, and an area. The first of these, the point count, is probably the most familiar among metallographers. The second count, the number of intersections a test line makes with particle outline, is somewhat more recent in its origin and application. The third counting measurement, the number of particle sections observed in unit area of the plane of polish, has long been used in the estimation of grain sizes. The real utility of these three counting measurements lies in the fact that they are rigorously and unambiguously related to certain extensive geometric properties of the three-dimensional structure of which the metallographic section is a sample. These relationships will be reviewed briefly below. Of somewhat secondary importance to the fundamental relationships is the observation that, if some simplifying assumptions about the geometry of the three-dimensional structure are introduced, manipulation of the counting measurements gives a more complete description of the structure. Specifically, in addition to the extensive properties which these measurements rigorously estimate, the number of particles, their size, and their shape may be determined. The purpose of the present paper is to explore the consequences of introducing the assumption of constant size and shape. A later paper will deal with the estimation of geometric properties of structures which may be characterized by a two-parameter size distribution. It should be mentioned that the introduction of this simplest of assumptions, while clearly not generally justified in metallurgical structures, is not without precedent. For example, many estimates of the number of particles per unit volume of structure, based upon a single counting measurement, are scattered throughout the literature.13 Virtually all of these developments assume a constant particle shape, e.g., spherical or polyhydral, and constant size. That such an assumption is necessary is evident from the fact that, for more general structures, more than a single parameter is required to describe the three-dimensional structure, so that the determination of a single parameter on a section would be insufficient to specify the structure. Similar developments for the estimation of particle size from a single counting measurement, e.g., routine grain-size determinations, make the same very limiting assumption,435 but have nonetheless proven of practical value. The present paper embodies a generalized approach to the development of relationships among the two-dimensional counting measurements and the three-dimensional geometry of the structure, subject to the assumption of constant particle size and shape. It is the hope of the author that by presenting the relationships and the assumptions involved in dealing with this approximation, in a single, unified treatment, the reader may be impressed with the usefulness of the counting measurements, may be guided in their application to the estimation of details of the geometry in specific structures in which he may be interested, and may be moved to apply the results, with understanding, to new structural problems. Several authors6, 7 have demonstrated independently that it is possible to obtain unbiased estimates

Jan 1, 1964