Search Documents

By John W. Cloud

THE delivery of blows upon roadway structures by the locomotive engine at high speed, although long recognized, has, perhaps, not been a generally understood in severity, relation to speed, and cause as is desirable in matters of such importance. Some points of explanation, with illustrative diagrams, are, therefore, submitted to your attention, preparatory to a note on "Steel for Bridges," also submitted. In order that a locomotive may run at high rates of speed with-

Jan 1, 1881

By C. H. Mathewson

BeRyllium, magnesium, zinc and cadmium, together with mercury, constitute a coherent sub-group of the periodic system and these metals, excepting mercury, have been studied in sufficient detail by the new X-ray diffraction methods to prove their common adherence to the hexagonal close-packed type of crystal structure with a progressive increase in axial ratio as we pass through the group from beryllium to cadmium. The first four columns of Table 1 summarize the data on crystal structure of these metals reported in the International Critical Tables.' The last two columns are based on results obtained in the present investigation. Twinning has often been observed in zinc and cadmium. The general aspects of this twinning are abundantly illustrated by photomicrographs, diagrams, etc., in the papers by Romig, and Mathewson and Phillips reported to this Institute in 1927.2 A determination of the composition

By K. H. Nimerick, G. P. Laflin

Laboratory data and field tests indicate that substantial losses of valuable coal can be caused by wind erosion. Wind tunnel tests show the effects of wind velocity and particle sizing on the amount of coal lost while in transit. Different coals were evaluated to determine the variables associated with wind erosion. The erosion losses can be substantially reduced by using a binder, or crusting agent, to consolidate the surfaces of the coal into a solid mass which resists erosion. This not only reduces economic loss but minimizes polllution.

Jan 1, 1980

By William E. Ford, Edward Salisbury Dana

1. Simple Hydrocarbons. Chiefly members of the Paraffin Series C,H2,+2. SCHEERERITE. In whitish monoclinic crystals. Perhaps a polymer of marsh-gas (CHI). Found in brown coal at Uznach, Switzerland. HATCHEITITE. Mountain Tallow. In thin plates, or massive. Like soft wax. Color yellowish. Indices, 1.47-1.50. Ratio of C to H = nearly 1 : 1. From the Coal-measures near Merthyr-Tydvil in Glamorganshire, England; from Galicia. PARAFE-IN. A native crystallized paraffin has been described as occurring in cavities in basaltic lava near Paterno, Sicily. Indices, 1.49-1.52. OZOCERITE. Mineral wax in part. Like wax or spermaceti in appearance and consistency. Colorless to white when pure; often leelr-green, yellowish, brownish yellow, brown. Indices, 1.51-1'54. Essentially a paraffin, and consisting chiefly of one of the higher members of the series. Occurs in beds of coal, or associated bituminous deposits, as at Slanik, Moldavia; Roumania; Boryslaw in the Carpathians. Also occurs in southern Utah on a large scale.

Jan 1, 1922

Safety and health are no longer secondary responsibilities but must be of paramount concern to every mining operation, according to Anthony J. Thompson, an attorney with Hamel, Park, McCabe & Saunders of Washington D.C. The Mine Safety and Health Administration (MSHA) forecasts an estimated 19,000 inspections during 1979, and the economic and psychological impact of these inspections may he significant. To illustrate his point Thompson reviewed the experiences of a relatively large operation during a recent MSHA visit. The inspector was on the premises for two months, issuing between 250 to 300 "significant and substantial" (s&s) citations. During the most intensive period, about one month in duration, the operation experienced a production loss estimated between 2500 to 3000 tons; an accident rate up 30% over the previous month and 20% over the same month in the preceding year; 100% of the safety director's and safety engi¬neer's time was devoted to the inspection; 50% of top level management's time; and 90% of the mid-level or front line supervisory's time.

Jan 11, 1979

Jan 1, 1951

By C. G. Dunn

THE present note, which was given in the form of a Research in Progress item,' traces the origin of secondary recrystallization grains produced on annealing a cold rolled bicrystal specimen. The investigation began with the realization that a recently acquired conception for the origin of secondary grains produced on annealing cold rolled single-crystal specimens might require modifications for the case of polycrystalline materials. The stated conception2,3 begins with several conditions to be met by primary recrystallization: 1—a primary re-crystallization structure to consist of many small primaries and relatively few large primaries (diam- eters two or three times the average); 2—a primary recrystallization texture to consist of one strong preferred orientation or component and one or more weak components; and 3—a primary recrystalliza-tion structure-texture combination with some of the large primaries belonging to the weak components of the texture. When these conditions occur, some of the large primaries from the weak components of the texture

Jan 1, 1955

By W. H. Fluker

Until recently, the universal practice in New Zealand was dry-crushing and direct cyaniding. With ores containing no mineral sulphides, and little or no coarse gold, 'this method, in spite of its many disadvantages, gave excellent results, and was by far the best one available, pending the solution of the slimes-problem. But the situation has now been changed. The successful treatment of the slimes, enabling the mines not only to do away with dry-crushing, but also to deal with the mineralized ores of the lower levels, which are, for obvious reasons, quite unsuited to that method of treatment, has made wetcrushing universal; and this may be taken as satisfactory proof of its superiority over the former practice. In the lack of accurate information from plants operating successfully, particulars of experimental trials carried out on a working-scale at the Waitekauri Extended mine, Maratoto,

Jan 1, 1903

By W. A. Boyer, A. W. Beck

At the Morning mine of American Smelting & Refining Co. it was particularly important that there be a means of signaling the engineer from the moving cage in the shaft. Because of the shifting ground in which the shaft was located, buckling timber made it extremely difficult to keep a continuous bell line serviceable. In 1930 engineers considered a moving contact pantograph arrangement between the cage and two stationary messenger wires strung on insulators in the shaft compartment next to the cage. The idea was abandoned because falling material in the shaft and speed of hoisting made it difficult to maintain communication. Later in 1934 a manufacturing company was consulted about the use of an electric eye or a radio signal. As the shaft was located in a return air stream of nearly 100 pct relative humidity, there was too much fog for the electric eye to be used. The radio signal was considered, and it was believed feasible to generate electric static on the cage, locating a radio receiver at the top of the shaft, but the manufacturing company's research department was too busy to work on it at that time.

Sep 1, 1955

(Under this heading will be published notes sent to the Secretary of the Institute by members or other persons introduced by members.) Mining Geologist. Age, 34; wide experience in all Lake Superior iron-ore districts and Arkansas bauxite district. Examinations, tonnage estimates, reports, direction of prospecting, geologic mapping, churn and diamond drilling. Excellent references. A-2681. Mine Superintendent or Manager. Graduate mining engineer, age 31, married, 10 years' experience, now in government employ as metal-lurgist, desires employment with reputable mining company. New York interview if desired. A-4219. Research Engineer, now in Chile on erection of 50-ton mill with modern machinery for treatment of Chilean nitrate, desires connection, from the first of next year, with firm operating in South or Central America. A-4915. Mining Engineer. Young graduate of Michigan College of Mines; capable of handling men, conscientious worker; desires a position that will lead to assistant superintendency. Any place in the United States. Initial salary relatively unimportant. A-5195. Metallurgist, married, age 25; technical graduate; 3 years' experience in blast and open-hearth furnaces, blooming mills, metallographic, and heat treatment work; desires position as sales engineer in the Pittsburgh district. A-5196.

Jan 12, 1919

By E. C. Pechin

At the September meeting of the Iron and Steel Institute of Great Britain, Mr. Charles Wood, of the Tees Iron-works, read an interesting paper on "Further Improvements in Blast-Furnace Hearths," which was followed by an animated and instructive discussion. If the durability of hearths and in-walls is a matter of interest in England, where furnaces stay in blast from eight to twenty years, it

By David A. Thomas, Eugene S. Meieran

MECHAMCAL, electrical, and other property measurements are often more easily made on wires than on sheets. In order to carry out transmission electron microscopy on the same material used for property determinations, we have developed a method for preparing thin foil specimens of wires. The technique was developed for 0.030 in. diam tungsten wires, and is a modification of the thinning techniques used by Wilsdorf, et al 1 A length of wire is first ground to about 0.010 in. thick by mounting the wire in low melting temperature wax, hand grinding a longitudinal flat, removing and reversing the wire in the mount, and then grinding a second parallel flat. The 0.030 in. wide and 0.010 in. thick strip is cut into 1/8 in. lengths to fit in the specimen holder of the electron microscope. Next the specimen is gripped in platinum-tipped tweezers (the anode) and placed 2 mm below a hol- low copper cathode with a 0.010 in. ID nozzle. Electrolyte, 10 pct NaOH, flows by gravity feed through the nozzle onto the specimen, as shown in Fig. l(a). Polishing is carried out until a shallow impression is made on one surface, and then the specimen is turned over and the opposite surface indented. The metal between the two impressions should be about half the specimen thickness, as is shown by the heavy line in the cross section in Fig. l(b). The entire specimen is then electropolishedin 2 pct NaOH until a hole appears at the location of the indentations. The apparatus is shown in Fig. 2, and is essentially the same as that used by Wilsdorf et al. at The Franklin Institute. Light is reflected by a mirror onto the bottom surface of the specimen! which is viewed by a stereoscopic microscope placed above it. Polishing is carried out until light is seen, indicating that a hole has formed, and then immediately stopped. The specimen is washed in water. alcohol, and ether, and is then ready for examination. The specimen should be reversed in its platinum clip during electropolishing to insure equal polishing on both sides of the impression. For tungsten, indenting at 120 v and 0.04 amp takes less than 1 min, and final polishing, at 10 v and 1 amp, less than 5 min. The portion of the specimen available for transmission microscopy surrounds the hole, as is seen by the dashed lines in Fig. l(b). Slight electroetch-ing accompanying electropolishing reveals the mi-crostructure, as seen in Fig. 3(a) by light microscopy. Low-magnification electron microscopy, as in Fig. 3(b), enables the same areas and grains to be viewed and identified when subsequently examined at high magnification. Fig. 4 is a typical structure of

Jan 1, 1963

By Thomas V. Falkie, Robert Stefanko

Higher education is in serious trouble in the United States. With increasing costs threatening to create a taxpayer's revolt, serious thought must be given to determining whether or not we can continue to afford our present educational policies. Disinterested students with little aptitude are pushed into over- crowded universities by well-meaning parents, but they lack real objectives beyond achieving that great status symbol-the degree. Advanced degrees are heaped upon the baccalaureate degree, and the pursuit of the pure and social sciences continues at the expense of engineering and technology.

Jan 1, 1971

By J. E. Lawver, W. D. Carrier

During the past 20 years, millions of dollars in research effort have been spent to improve methods of phosphate clay dewatering and disposal. Although to date no proven large-scale system has been developed that will result in ultimate below ground storage without the use of at least temporary dams, considerable progress has been made and a variety of techniques are being tested, some on a large scale. This paper summarizes the use of mathematical and centrifuge (physical) models that can analyze and evaluate various systems for the consolidation of phosphatic clays. These provide a powerful tool for engineers responsible for land management and mining waste disposal.

Jan 1, 1985

By W. Hume-Rothery

IN recent interesting papers,1,2 Bardos et al. have described ternary Laves phases of the type A2(BsSi) and A4(B5Si3) where A = titanium vanadium, niobium, and so forth, and B = manganese, iron, cobalt, or nickel; other more complex formulae have also been established. In these phases, silicon plays the part of the smaller B atom of a Laves phase AB2, and the interatomic distances show that the effec- tive silicon radii lie between 1.16 and 1.21Å, and are thus very much smaller than the metallic radius of silicon for CN = 12. It does not seem to have been pointed out that these small atomic radii are almost the sape as the normal covalent radius of silicon (1.174Å). If, therefore, silicon acts as an acceptor of electrons as suggested by Bardos et al.,1 it appears to do so, not by the building up of a negatively charged silicon ion which would be large, but by the formation of what are very nearly or may be actually normal covalent bonds. Since a covalent bond contains two electrons, its formation would reduce the number of electrons available for bonding in other parts of the structure, and in this way the effect of silicon in stabilizing the o phase at high electron concentrations might be understood.

Jan 1, 1965

Both drilling and production in Rumania showed increases in 1934 over 1933. The drilling totaled 1,138,000 ft. and production 63,500,-000 bbl., being increases of 50 and 15 per cent, respectively. During the year production gradually increased from 155,000 bbl. per day in January to 180,000 bbl. in September, and then declined slightly to the end of the year. The increases were largely due to competitive drilling in the Gura Ocnitei field (including west extension to Viforata). Wells completed during the year totaled 238, of which 215 were oil producers. The outstanding development of the year was the discovery by Steaua Romana of what appears to be a major field at Bucsani. Other important discoveries were a three-mile west extension of the Gura Ocnitei fault to Viforata and a five-mile east extension of the Moreni field to Calinesti. Strictly speaking, the latter cannot as yet be called an extension. Oil sands have been corded in the Meotic, and in all probability production will be established in 1935. The Calinesti discovery greatly restricts the unproved area between Moreni and Baicoi, and the probabilities of

Jan 1, 1935

In the fall of 1937, the Department of Mining at Penn State was being reorganized and the department records were moved to the Records Room of the School. An inventory of the contents of the vault disclosed six folders of records that had been forgotten for 27 years. These files, apparently preserved by former Dean W. R. Crane, plus the recollections of several former members of the Association described below, unfolded the "lost chapter" in mineral industries education.1 It was apparent at an early date in technical education that an association of mining schools with common interests and problems would have definite value. By 1902 sufficient interest had developed in this idea to cause the holding of a preliminary meeting for the purpose of organization. The first meeting was held at the Montana School of Mines on September 4, 1902. At that time, officers were elected and resolutions were adopted that there be formed an organization to be known as the National Association of State Mining Schools. The object and purpose of this Association was to advance the interests of state mining schools in every way, particularly by promoting legislation for the benefit of such schools. The second meeting was held September 10, 1903, and a resolution was passed that the American Mining

Jan 1, 1950

By Graham MacFarlane

The eastern coal-field of Kentucky covers about 11,000 square miles of territory. On the east and south it extends to the State lines of West Virginia, Virginia and Tennessee. Its western boundary may be roughly described as an irregular line beginning at the Ohio river, in Greenup county, thence through the counties of Carter, Menifee, Wolfe, Estill, Jackson, Rockcastle, Pulaski and Wayne, to the Tennessee line. The changes in the rock-intervals and in the coal-seams from the northeastern end of the field to the south and southeastern end are so great that no satisfactory identification of the coals has yet been made, and the correlation of the Kentucky coals

Jan 1, 1896

By C. J. Barber

This paper Donald describes how New Jersey Zinc Co. made surveys for a connection between the Ivanhoe and Van Mater shafts at Austinville, Va. Except to say that the two faces had to meet "accurately" on line and grade, Donald does not indicate the required precision. Assuming that there were 24 angles in the 1 ½ -mile traverse and 15 in the one-mile traverse, it can be shown that if the average error in plumbing each shaft was ±30" and the average error in measuring each traverse angle was ±10", then the average error at the point of connection would have been about ±1.9 ft normal to the line between the shafts. This calculation assumes that any errors in the triangulation would be negligible compared with the errors in the plumbings and traverses, and it also neglects taping errors. With no constant errors or blunders, the latter would be important only in lines normal to the line between the shafts.

Jan 7, 1959

By C. A. Crawford

NICKEL and the nickel-copper alloy, the latter generally referred to as monel metal, are available in a variety of wrought and fabricated forms, of which the following are regular commercial products: [ ]

Jan 1, 1928