Search Documents

By Howard Talbot

THE history of the development of the strip in- dustry, mentioned in this paper, was covered in considerable detail by Stephen Badlam in his paper presented. before the American Iron and Steel Institute at its meeting in New York last October. The description of progress in rolling strip there out-lined will be found good reading by anyone interested in the subject. Quoting from Mr. Badlam's paper, "For practically thirty years, we find no record of the use of the backing-roll principle, until in 1916 the Lukens Steel Co., Coatesville, Pa., put in a 206-in. plate mill of the four-high type. This was a reversing mill with two 32-in. working rolls and two 50-in. backing rolls and is today making the widest and heaviest plate made anywhere in the world." The functioning of this mill, though rolling hot plate, is, on account of the extreme width and thinness of plate rolled, quite comparable to the rolling of wide strip either hot or cold and was a considerable factor in demonstrating the marked advantages available with the four-high or backing-roll mill for thin accurate rolling. As the writer has brought out, a demand for a product, the rolling of which required the character-istics of the backing-roll mill, was broached by the In-ternational Nickel Co. This resulted in an inquiry of March, 1924, for the building of a mill capable of cold-rolling wide nickel and monel metal sheets or strip, as mentioned. It may be of some interest to note, that whereas the .six-roll cluster mill with plain bearings was built for this installation, the mill designed by the United En-gineering and Foundry Co. for this inquiry was of the four-high type with roller bearings on the backing-roll necks, being essentially the same design as the four-high roller-bearing mill built in 1925 for the Rome Brass & Copper Co. This Rome mill, to quote again from Mr. Badlam's paper, "fulfilled every requirement, and was the model on which succeeding mills of this type were built."

Jan 5, 1928

By J. Chipman, H. A. Wriedt

DURING the past twenty years, a considerable background of knowledge has been built up on the chemical behavior of oxygen in liquid iron. Little is known regarding oxygen in liquid nickel or the effect of nickel as an alloying element on the behavior of oxygen in liquid steel. The solubility of oxygen in liquid iron was determined by Fetters and Chipman' and, more precisely, by Taylor and Chipman.' The Ni-NiO eutectic was placed by Merica and Waltenberg"' * at 1438°C and 0.24 pct 0, and this point has been confirmed by others." O It was reported by von Bohlen und Halbach and LeitgebelT that nickel and its oxide are miscible in all proportions at 1600°C, but this report is discredited by observations of others. The melting point of NiO according to von Wartenberg and ReuschV s 1990°C. Approximate values of oxygen solubility at several temperatures were reported by Hensel and Sc0tt.O The data of Krupowski and Balickil0 are inconsistent with those of Hensel and Scott and indicate a solubility less than half that found in the present study. For oxygen solubility in Fe-Ni alloys under pure iron oxide-nickel oxide slags, only the scattered data of von Bohlen und Halbach and LeitgebelT are avail- able. The careful work of Bardenheuer and Brauns" involved silica-saturated slags. The equilibrium between Fe-Ni alloys and iron oxide-nickel oxide slags was studied by zur Strassenu and by Jander and Senf,u but no oxygen analyses were reported. Oxygen in Pure Nickel Apparatus and Nlethod: Samples were taken with a "Taylor sampler" from a bath of molten electrolytic nickel held under an air atmosphere in a magnesia-lined 30 lb induction furnace. Saturation of the melt with oxygen was effected partly by the addition of chemically pure black nickel oxide and partly by the air atmosphere. Samples were taken only when there was a clearly visible oxide phase present. To avoid contamination of this oxide phase, the silica-sheathed Pt—Pt-10 pct Rh thermocouples, by means of which temperatures were measured, were immersed in the melt for the minimum time consistent with accurate reading. Samples and temperature readings were taken only after the furnace had been

Jan 1, 1956

By John C. Long

The advantages of firebrick regenerative hot-blast ovens being thoroughly appreciated by those engaged in modern blast-furnace practice, the important question now is to obtain the best and most efficient apparatus. The apparatus invented by the writer, and described in this

Jan 1, 1885

By Charles Rich, Robert Munson, Leonard Obert

Improved methods of predicting the caving characteristics of ore bodies is discussed. Experiments were conducted at Climax mine, Climax, Colo., on varied rock compositions. The cavability of adjacent areas, as well as seismic energy absorption proved to be good factors in determining cavability. Seismic velocity, core recovery, and rock quality designation (RQD) were found to be not as reliable.

Jan 1, 1977

By D. M. Bondurant

Auger mining-extraction of coal with large diameter augers is proving profitable in recovering coal left after stripping has ceased to be economical. Its many advantages-low initial cost of equipment, low operating cost, low power demand, adaptability to selective mining, simplicity of operation, etc.-have excited the interest of some in the industry in its possibilities for underground operation.

Jan 5, 1951

By H. P. Leighly

WORNER1 briefly studied the embrittlement of titanium by mercury. He found that mercury will wet the titanium surface at 400°C in vacuo, if the specimen had been heated previously to 700°C to dissolve the oxide coating. Subsequent exposure to the atmosphere causes the mercury film to recede rapidly. Bending of the titanium specimen even after the mercury film has receded results in a brittle fracture. For the study of the embrittling effect of mercury on titanium, specimens 2 by 12 by 0.051 in. were cut from RC-130-A sheet, an alloy having a nominal 8 pct Mn content and a mixed a-ß structure. The specimens were stressed horizontally at a predetermined value after which a plastic ring having a cavity 1/2 in. diam by 1/2 in. deep was placed on the specimen. The cavity was filled with mercury and a hole was drilled in the specimen through the pool of mercury. If the stress level was high enough, fracture occurred instantaneously with the drilling. By repeating the test at different stress levels, the threshold stress can be determined. Mercury embrittlement causes a drastic reduction in the ultimate tensile strength of this alloy from 132,000 psi to about 15,700 psi. The drilling of the hole, in the absence of mercury, does not change the tensile properties. Fig. 1 shows the typical fractures observed as a result of the embrittlement of this alloy by mercury. The central portion of the fracture was brittle represented by the jagged region which appears to have occurred on the shear planes at about 45 deg to the stress axis. Ductile fracture, which is perpendicular to the stress axis, occurred near the specimen edges accompanied by a reduction of the specimen thickness. Examination of the fracture reveals that only in the brittle region does mercury wet the

Jan 1, 1962

By J. D. Livingston, Bruce Chalmers, R. L. Fleischer, R. S. Davis

INTERACTION of dislocations on intersecting slip planes has long been considered a primary cause of work hardening in metals. Easy glide and low work-hardening rates have been observed experimentally only when single-crystal specimens were oriented so that one slip plane was initially favored. When single-crystal specimens have been oriented so that initially two or more slip planes were equally favored, high initial work-hardening rates have been observed. In a polycrsstalline aggregate, glide on five systems is in general necessary for a crystal to deform in conformity with the change in the shape imposed by the other crystals.* Only a small fraction of the crystals of a polycrystal will be oriented so that two

Jan 1, 1958

By J. L. Sepulveda, R. F. Yap, R. Jauregui

INTRODUCTION The Third Theory of Comminution, oftentimes called the Bond Theory, was first published by Fred C. Bond in 1952. Since then, it has been widely used in the milling industry to size crushing and grinding equipment as well as to predict and evaluate their performance. Although two other comminution theories were advanced almost a century earlier, one by Rittinger, 1867, and the other by Kick, 1885, their use was limited because they did not agree with actual commercial comminution systems (Bond, 1961). According to Bond's Third Theory, the work input is proportional to the new crack tip length produced in particle breakage, and equals the work represented by the product minus that represented by the feed. For particles of similar shape, the crack tip length is equivalent to the square root of one-half the surface area, and the new crack length is proportional to [(1/vT - vF)]; where P and F are particles diameter of product and feed, respectively. For practical calculations, the particle diameter can be expressed in terms of the 80% passing sizes, P and F, respectively. Therefore, the work input is given by, [10 _ 10', W = Wi [7P_7F(1)] Where W = the energy input to the mill, (kwh/t) Wi = Work Index, (kwh/t) P = square sieve opening which 80% of the product passes, (microns) F = square sieve opening which 80% of the feed passes, (microns) Equation (1) is the mathematical statement of the Third Theory, or the Bond equation. Numerically, the work index is the energy required in kwh/t to reduce a given material from theoretically infinite feed size to 80% passing 100 microns. The work index of a particular material is determined in the laboratory by conducting the standard Bond grindability test. Bond developed separate tests for the rod mill and the ball mill. The simplified test method described in this paper, which is used at Anaconda Research Center to approximate the work index, is an alternative procedure to the ball mill

Jan 1, 1982

By R. O. Neal

There are two main sources of the water that floods productive oil or gas sands. The water may rise from the lower depths of the producing stratum, or it may come from beds above or below the oil-bearing formation. Usually the recovery of oil is decreased by water entering the oil sands, and most oil-field waters, especially those of deep wells, tend to foster the formation of an emulsion, which is expensive to treat. This paper deals with a method of distinguishing between waters that encroach upon oil-bearing beds from sources in the same stratum and waters that reach the oil sands from horizons above. In order to remedy effectually water difficulties in oil and gas wells, it is absolutely necessary to determine the source of the invading water. Sometimes evidence such as the structural relations between the strata penetrated by deighboring wells and those found in the well under investigation is not adequate; also, data from drill logs and well records, from mechanical tests made on the wells by plugs, testers, drilling tools, etc., and from tests by chemical indicators such as eosin and Venetian red, may be unsatisfactory, for such data may fail to locate the source of the infiltrating waters. As a resort in such cases, the application of chemical analyses, that is, the comparison of an analysis of the water in question with that of typical waters from the various water horizons in that particular district, has in certain instances proved of value. This method has been used to advantage in the Westside Coalinga field of California, where the source of water may be fairly definitely determined , from its composition. The chief conclusions concerning the chemistry of the oil-field waters in California by G. S. Rogers1 are: "Oil-field water is not necessarily salty, as is generally believed, and may not be even slightly salty to the taste. The degree of concentration of chloride in such water is governed primarily by local conditions and is not affected by the position of the water in relation to oil. Sulfate diminishes in amount as the

Jan 1, 1920

By E. C. Winegartner, A. A. Ubbens

The company attempting to sell coal to large utility plants is faced with a confusing array of quality parameters and specifications which are often poorly understood by both the utility company and coal supplier. While these specifications are placed on the coal by the utility company, many of them originate with the boiler manufacturer who must guarantee that his product will perform satisfactorily on the design coal. A proper understanding of these parameters by both the coal supplier and utility company can lead to a better understanding of their mutual problem. This paper brings together most of the parameters in common use today and attempts to show what the parameters mean to the boiler designer, particularly in the area of boiler slagging and fouling.

Jan 1, 1977

By W. E. Rice

The ceramic industry has to do with forming or molding articles of clay, and imparting to them their characteristic properties of permanence, strength and color by subjecting them to heat treatment in kilns. This heat treatment is commonly known as "firing" or "burning." The art of firing clay ware antedates the industrial use of coal; hence wood was the fuel first used, and the earliest kilns were built to burn wood. The majority of the clay ware produced today is fired in periodic kilns that are essentially enlarged structures similar to the earliest enclosed kilns; a kiln consists of a large chamber 16 to 32 ft. dia. (or rectangular) in which the ware is charged and fired either in direct contact with flame or hot gases from the fuel, or in saggers which shield the ware from direct contact with the gases. The fuel is burned in a number of small furnaces built in the thick wall that encloses the chamber; these furnaces are from 16 to 36 in. wide and from 3 to 5 ft. long; some of them have horizontal or sloping grates, but many have no grates; the last are called "dead-bottom" furnaces. The temperature necessary to mature the charge in the kiln varies for different clays; for some it is as low as 1800°, and for others as high as 2700" F. Wood was an ideal fuel for the low temperatures that were used in early kilns; it burns freely and produces a long, clean flame, which promotes uniform distribution of the heat in the kiln; it does not coke and so restrict the passage of air through the fuel bed; the ash does not melt in the fuel bed to form clinker; and the ash that is carried into the chamber and deposited on the charge does not contain iron and sulfur to discolor the clay. The extent of the ceramic industry now precludes the general use of wood in kilns, so that today this industry is one of the large users of bituminous coal, burning more than eight million tons annually in kilns. Manufacturing plants usually are at or near the source of clay, with deposits of coal suitable for kilns occurring near the clay. The cost of coal is the largest single item of expense in the manufacture of clay ware, and, because all coals are not equally suitable for the process, the careful selection of coal is important. In this selection the desidera-

Jan 1, 1932

By H. H. Wade, N. F. Schulz

The large quantities of iron-bearing materials, including taconite, semi-taconite," and other low-grade ferruginous materials occurring in Minnesota and elsewhere, constitute an important potential source of iron. Satisfactory grade and recovery of iron ore concentrate cannot ordinarily be obtained from these ferruginous materials by simple methods of beneficiation. Iron is distinctive in that the free metal and two of its oxides [magnetite (Fe,O,) and maghemite (gamma-Fe,O,) ] are strongly ferromagnetic. The successful magnetic separation of natural magnetite from taconite has already been established on a commercial scale. The iron in semi-taconite, how- ever, occurs largely as goethite (Fe,Os.H,O) and hematite (Fe90,) which do not respond to ordinary magnetic separation methods. Magnetic roasting converts these iron oxides to magnetite, which can, after liberation, be magnetically concentrated.

Jan 11, 1960

By Robert Mehl

IT has been shown that quenched iron of high purity exhibits a Widmanstätten figure much resembling martensite in appearance.1 This figure exhibits a maximum of four directions of the surface traces that characterize it, suggesting that a Fe forms from y Fe in plates parallel to the {111}, octahedral, planes in the y lattice. Because of this, and also because of the general similarity to the structural appearance of martensite and to the Widmanstätten figure obtaining in slowly cooled hypoeutectoid steels it has been suggested2 that the orientation relation-ships obtaining between the y and a phases in pure iron are identical with those demonstrated in martensite3 and in slowly cooled hypoeutectoid steels,4 and indeed that the crystallographic mechanism of formation of a Fe from y Fe is the basic mechanism determining the orientation relation-ships found in both martensite and in slowly cooled hypoeutectoid steels. This paper will present experimental evidence in support of this view.

Jan 1, 1934

By Stanley L. Arnot

The Mother Lode district in California is probably better known as the land of Bret Harte and Mark Twain than as a gold-producing district, although in this respect it holds an important place. The history of quartz mining on the Mother Lode dates back to the '50s, when, after the first fever of the gold rush, men began to look for something more permanent, if not more lucrative, than the placers. Since that time, the discoveries, shutdowns, and reopenings of the many mines, together with the varying fortunes of their numerous operators, constitute an interesting chapter in California history, but one too long to include in a description of mining methods. The district is well situated, so far as physical conditions are concerned. The Mother Lode extends along the western slope of the Sierra Nevada Mountains, about half way between the crest and the Sacramento and San Joaquin Valleys, the country traversed consisting of low rolling hills—typical foot-hills. The elevation varies from 1000 to 1800 ft. and the climate is most desirable. There is an abundance of water, timber is easily obtained from the higher foot-hills a few miles east, and cheap hydro-electric power is generated practically on the Lode. These natural conditions are conducive to low costs in mining and have been the deciding factor in allowing profitable exploitation of the comparatively low-grade orebodies. Transportation facilities are not bad. Five branch railroads, from the main trunk lines in the valley, tap the district at intervals of from 10 to 30 miles, and the roads connecting these are fairly good for trucking purposes. Labor is made up of several nationalities, the principal ones being American, Spanish, Jugo-Slav, Italian, and Mexican. There were few Mexicans on the Lode prior to 1919, but the shortage of labor, experienced generally by the mining camps of the country in the years following the war, made necessary the hiring of some. The percentage of Mexican labor rapidly increased in 1920 and for a year or so thereafter, but it has now diminished until at most of the mines only a few Mexicans are working. Of the different nationalities, Americans are the most efficient and Mexicans the least.

Jan 1, 1925

By Chi-Yuen Wang, Chaw-Long Chu

The time-dependent volumetric constitutive relation for a San Andreas fault gouge and a consolidated kaolinite are experimentally determined at confining pressures to 200 Mpa, under creep condition and at ultrasonic frequency. At any given pressure, the bulk modulus determined at 1 Mhz frequency is identical to the "elastic" modulus determined at a stepwise change of pressure. After the pressure change, there occur a time-dependent change of volume and thus the effective bulk modulus. The constitutive relations may be modeled by a standard linear viscoelastic medium with pressure-dependent moduli and viscosity. For the San Andreas fault gouge, viscosity increases from 2x10 13 poise, at 17 Mpa, and 10 14 poise, at 100 Mpa. For kaolinite sample, the corresponding values are 3x10 12 poise and 10 13 poise. These results imply that both stress and pore pressure in fault zones may show time-dependent variations in response to a change of state of stress, such as that occurring after an earthquake.

Jan 1, 1982

By Robert E. Delavault, Harry V. Warren

Geochemistry in all its branches is playing G an increasingly important part in the business of mine finding. Although geochemical studies were commenced more than 50 years ago, interest in this subject did not become widespread until the late 1930's when in Scandinavia and the U.S.S.R. a whole series of investigations were initiated. Unfortunately for those in North America, the results of these investigations have only recently become available. In Canada and the U.S. geochemistry as a serious mine finding tool dates back only to the period following World War II. This article deals primarily with soils, which have found widespread acceptance as a useful tool in geochemical prospecting. Actually soils vary greatly in texture, structure, profile, and mineral background. Soil sampling poses no hardship for normal intellects, but it does assume an elementary knowledge of soil science and of the chemical problems involved in determining the absolute and relative amounts of a particular element in any particular soil.

Oct 1, 1956

By S. Fukushima, E. Kimura

In the Mitsubishi beneficiation process of ilmenite, chlorine is regenerated in the dechlorination furnace where the gases produced from a selective chlorination of ilmenite are directly introduced. The present paper describes a reaction mechanism and mixing characteristics of the reactant gases for dechlorination of ferric chloride with oxygen. A furnace of a small diameter where the reactant gases passed through in the state of nearly plug flow was used for determination of the effects of temperature and of partial pressures of ferric chloride and oxygen on the rate of the reaction. The experimental data of the reaction rate were applied to various models for calculations of the rate equations and the most suitable reaction model was determined. The results of the experiments also showed that effects of gas mixing onto the reaction rate could not be ignored, so that experiments of gas mixing was carried out. Gas flow patterns and scale effects were observed with use of transparent model furnaces of different sizes.

Jan 1, 1976

By P. Somasundaran, R. D. Kulkarni

Reagentizing at elevated temperature, reported in the past as beneficial for the flotation of hematite using oleate, is studied here as a function of collector concentration, solution pH and ionic strength at various levels of conditioning temperature. The study revealed strong interactions between variables; particularly, the effect of conditioning temperature was found to strongly depend on the ionic strength of the solution. Thus, while an increase of conditioning temperature at lower ionic strengths or that of ionic strength at lower temperatures resulted in an increase of both flotation and grade, an increase of the former at higher ionic strength or that of the latter at higher temperatures caused a significant decrease in both responses. These observations have been explained in terms of the increased chemisorption of oleate at elevated temperatures and the temperature effect of ionic-strength on the salting out of the oleate from the bulk solution. The above effects which were first observed during Hallimond cell flotation tests were subsequently tested with Denver cell using low-grade iron ore. The results obtained using the two test procedures were in agreement with each other. The implications of these effects and interactions for process control of optimum flotation performance must be noted since variation in the levels of the above parameters are likely under plant conditions.

Jan 1, 1978

By R. F. Sheldon

Largest uranium deposit in the Northwest is Dawn Mining Co.'s Midnite mine on the Spokane Indian Reservation. The orebodies lie along the contact of granite and metamorphosed sedimentary rock and are controlled by faults and shear zones near the granite contact. In the oxidized zone the deposits consist mainly of the secondary uranium mineral meta-autunite; sooty uraninite and primary uranium minerals are known to occur at greater depths. Elevations in the mine area range from 2500 to 3500 ft. The rolling hills and low, rounded mountains are covered with grass and evergreen trees. HISTORY AND DEVELOPMENT Original showings were discovered with a geiger counter in the spring of 1954 by prospectors Jim and John LeBret. High radioactivity in several schist outcrops was found due to scaly coatings of a greenish-yellow, fluorescent mineral, later identified as meta-autunite. Prior to this time autunite was not known to occur in the state of Washington, and no significant uranium deposits had been found in the Pacific Northwest. Outcrops in the area were few, and most of the ground was mantled with 2 to 10 ft of overburden, but three other radioactive zones were discovered by prospecting the ridge southward along the strike of the schist near its contact with granite for three quarters of a mile. Midnite Mines Inc. was formed

Jan 1, 1960

By S. R. Zimmerley, John Gross

The method of measurement of surface on quartz particles was given in a previous paper.' With such a method the relation of surface produced in crushing quartz can be compared to the work in crushing without recourse to sieve sizing or microscopic measurement. In crushing, the work input must be known with a fair degree of accuracy. With crushers, rolls, ball mills, and similar apparatus the measurement of the work in crushing is subject to possible errors, due to friction in the transmission as well as in the machine itself. Moreover, relatively large quantities of material must be crushed to get an average figure. In the selection of a method of crushing, simplicity in design and operation was desired and this was most readily obtained by the use of a free-falling body. A description of the apparatus embodying this principle is given herewith. The Crushing Device The apparatus used is shown in Fig. 1 and in cross-section in Fig. 2. The material to be crushed is placed in the crushing chamber C in the steel mortar M. The mortar is 3 in. dia. by 3 in. high. Two mortars are used, one having a crushing chamber 1 in. dia. by 36 in. deep, with a capacity of 4 g. of quartz, the other having a crushing chamber 1 1/2-in. dia. by % in. deep, with a capacity of 12 g. of quartz. The position of the mortar is adjusted by means of three centering screws A. The steel plunger P, which fits neatly into the chamber, is placed on top of the material to be crushed. Plungers of different lengths were tried and as they were found to give practically identical results the length adopted was equal to the depth of -the chamber. The mortar rests on a solid steel base B but is separated therefrom

Jan 1, 1930