Search Documents

By D. H. Desy, L. C. Fincher

The magnesium-rich end of the Mg-Ti phase diagram was investigated. The liquidus, solidus, and solvus boundaries to 1 pct Ti were established. All alloys were prepared by saturating molten magnesium with titanium in a consumable titanium crucible under inert gas maintained at 230 psig. The liquidus of the Mg- Ti system was determined by analysis of dip samples taken from 700° to 1300°C under equilibrium conditions in a pressurized inert atmosphere furnace and by analysis of small ingots rapidly poured and quenched from 1400° to 1500°C. The solubility of titanium in magnesium ranged from 0.018 wt pet Ti at 700°C (0.012 wt pet at 650°C by extrapolation) to 1.035 wt pet Ti at 1500°C. The solidus for compositions ranging from 0.03 to 1.00 wt pet Ti was determined to be 650° ± 1°C by thermal analysis. The titanium solid solubility values ranged from 0.08 wt pet at 350°C to 0.19 wt pet by extrapolation to 650°C. The freezing reaction is peritectic. No intermetallic compounds were found in the system; the phase in equilibrium with molten magnesium saturated with titanium was found to be titanium with magnesium in solid solution. Solid titanium will dissolve at least 1.32 wt pct Mg. PREVIOUS investigations of the Mg-Ti system have shown considerable disagreement on the solubility of titanium in liquid magnesium. Furthermore, the solid solubility of titanium in magnesium has not been well established. Liquidus curves for previous work and for the present investigation are shown in Fig. 1. Aust and Pidgeon1 used a dip-sampling method on molten magnesium held in equilibrium with solid titanium under a protective atmosphere to determine the solubility and found that it ranged from 0.0025 wt pet Ti at 651°C to 0.015 wt pet Ti at 850°C. Eisenreich2 introduced titanium into molten magnesium by means of TiCL4 adsorbed on BaCl2. Ingots were then cast at various temperatures. Making the assumption that only the titanium dissolved in magnesium at the time of casting was soluble in H2SO4, Eisenreich determined the solubility of titanium in molten magnesium to range from 0.003 wt pet at 655°C to 0.115 wt pet at 800°C. Eisenreich also determined the solid solubility of titanium in magnesium to be 0.015 wt pet at room temperature and 0.045 wt pet at 500°C. Since the solid solubility just below the freezing temperature for the bulk of the alloy was much larger than the liquid solubility just above the freezing temperature, Eisenreich concluded that the freezing reaction was peritectic. Obinata et al.3 equilibrated molten magnesium with titanium in hermetically sealed titanium containers which were then furnace-cooled. The titanium content of the magnesium was then determined and found to range from 0.170 wt pet at 700°C to 0.85 wt pet at 1200°C. No intermetallic compound was found in the system. The Armour Research Foundation4 determined two points on the solvus by electrical resistivity methods: 0.00057 wt pet at 200°C and 0.0008 wt pet at 300°C. At higher temperatures, data were meaningless with no trends observable. The authors of this report believed that the lack of significant data at the higher temperatures was due to variations in specimen geometry, although there was no positive evidence to verify this supposition. The present investigation was undertaken to clarify the uncertainty in both the liquidus and solvus of the magnesium-rich end of the Mg-Ti system. EQUIPMENT AND MATERIALS The equipment used in this investigation, with some modifications, was essentially that used by Crosby and Fowler5 in their determination of part of the Mg-Zr phase diagram. The equipment, as modified for this work, is shown in Fig. 2. It consists of a sealed furnace chamber which can be pressurized with inert gas so that melts can be made above the boiling point of magnesium at atmospheric pressure. Melts are made by induction heating in a titanium crucible which, after diffusion of sufficient magnesium into the walls of the crucible to saturate the titanium at the sampling temperature, comprises the solid phase in equilibrium with the molten magnesium. Dip samples may be taken with the sampling tube, or the entire furnace may be tilted so that ingots may be poured into a mold in the side chamber. The principal difference from the earlier apparatus is in the thermocouple, which in the present equipment is enclosed in a protection tube and immersed directly in the melt. The tips of both the thermocouple protection tube and the sampling tube, which dip into the melt, are made of high-purity titanium. The 4 1/2-in.-long titanium tip of the sampling tube is threaded into a steel tube, O in Fig. 2, which extends through the top of the furnace. To determine whether the temperature at the tip of

Jan 1, 1969

By Bruce T. Stanley

A key point in the design and operation of a modern mining operation is the construction of what is called an ore-body model or block model. This model is a representation of reality constructed from predicted information. The blocks involved are merely subsets of the overall model which allows manipulation of the contained information on a local scale. In general, block models enable mine planners to effectively select the most promising means of extracting the ore both physically and economically. The uses of a block model can be quite diversified, but one must realize that a single model that satisfies all curiosities and forms of expertise is difficult to construct.

Jan 1, 1979

By Richard P. Rothwell

THE anthracite coals of Pennsylvania are all mined from large veins. A seam less than four feet. in thickness is generally considered as unworkable, those from which most of the coal now comes being from 8 to 30 feet thick. The system of mining employed is, almost without exception, that known as "chamber and pillar work;" that is, the coal is taken out of chambers of from 18 to 30 feet in width, and pillars of from 12 to 20 feet are left between these to support the roof. In general, the entire thickness of the seam, even

Jan 1, 1875

Upon nomination of the President, _the following Committee on Membership was appointed: Karl Eilers, Chairman, Arthur. S. Dwight, Lewis W. Francis, Louis D. Huntoon, Arthur L. Walker. The following resolution was then unanimously passed: WHEREAS, the integrity and life of this nation is dependent upon its ability to successfully defend itself against foreign aggression and attack, and WHEREAS, it is necessary that the nation he properly prepared to the end that our untrained patriotic volunteers he not uselessly slaughtered and our country disgraced and defeated, be it therefore RESOLVED: That the Board of Directors of the American Institute of Mining Engineers believe that compulsory universal military training should be at once instituted and that adequate, complete and immediate preparedness, should he provided. BE IT FURTHER RESOLVED: That, we believe that thorough and complete preparedness in the army, the navy and the industries of the country is vital; anything less is unsatisfactory and inefficient and may result in disaster to the nation.

Jan 5, 1917

By M. F. Werneke, J. A. Jones

Abstract- The use of a unique class of sulfhydryl collectors, the monoalkyldithiocarbamate salts ([RNHCS]) as direct collectors for malachite and azurite is presented. Microflotation and laboratory scale flotation tests were performed to define the collector properties of these reagents under a variety of flotation conditions. On the basis of the results, it is proposed that some property of the amine-hydrogen atom in the reagent has a significant influence on the unusual activity of these collectors for oxide copper minerals.

Jan 1, 1978

By D. W. Brunton

The erection of large metallurgical establishments for the treatment of gold, silver, copper, and lead-ores, at railroad arid topographical centers, where fuel and fluxes, together with proper oremixtures, can be cheaply and constantly obtained at all seasons of the year, has led to the very general introduction of a system of ore-handling known as "public sampling." By this system the ore, instead of being shipped direct to the mill or smelter, is sent to a public sampler, where it is crushed and sampled. Guaranteed samples are sent to the different metallurgical establishments, and the ore is then sold to the highest bidder. Though differing in many respects from the English system of "ticketing," the underlying principle is nearly the same, while the greater rapidity with which a lot of ore can be disposed of renders

Jan 1, 1885

By David J. Dunn

At a time when mill availability is at a premium, production costs are rising, and lead time for mill liner casting is a year or more, mill liner design is an important factor in ore grinding. Testing and selection of the optimum liner profile for a given set of mill operating conditions can improve mill capacity, reduce liner wear rate, and lengthen liner life. The mill liner that grinds best, lasts the longest, and costs the least is a necessity for economic mill operation. After testing four mill liner profiles for 3.96 X 3.65-m (13 x 12-ft) overflow ball mills, Climax Molybdenum Co. found that an improved design increased mill tonnage by 2.72 t/h (3 stph) while reducing finish grind by 1.7% minus 100-mesh, reduced liner wear rate, and almost doubled liner life.

Jan 12, 1976

By Rixford A. Beals

Dry grinding without balls is feature of this mill now in use in three countries on two continents. Materials being ground commercially include iron ore, gold ore, asbestos rock, and slag. New large beneficiation plants have been using an almost standardized crushing and grinding flowsheet. Typically a primary gyratory is followed by several stages of fine crushing and grinding is often carried out in a rod mill operating ahead of one or more ball mills. The clearly labeled trend is to an increasing number of stages with a decreased reduction ratio per machine. Current Aerofall mill installations represent a complete reversal of this trend-one mill replaces the several stages of crushing and grinding a more conventional flowsheet would call for.

Sep 1, 1955

By Dennis Z. Mraz

An engineering procedure for designing the minimum separation between solution mined caverns in bedded salt deposit is described. The procedure is based on data obtained by in-situ and laboratory test methods. The formulae utilize the concept that salt rock under high pressure in a deep salt rock deposit would behave as a perfectly plastic substance, and that the active opening surrounding a typical cavern could be described by a circular ellipsoid. The paper describes the calculations required for the safe design of a solution mined salt cavern field.

Jan 1, 1984

By E. S. Moffat

Members of the Institute who have visited the works of the Lackawanna Iron and Coal Company at Scranton, will remember the exposure of a large vein of anthracite coal in the rocky bank on the south side of Roaring Brook, near the blast-furnace. The vein is quite flat, and is exposed to view for several hundred yards along the banks of the brook, a few feet above the surface of the water. It is some ten feet in thickness, and is known as the Big Vein. At a point just opposite the blast-furnace, much of the coal from this vein was mined out many years since, the usual pillars being left to support the overlying rock and drift, which are here some twentyfive to thirty feet in thickness. Over thirty pears ago fire was communicated from an ore-roasting pile on the surface of the ground at this point, through an old shaft, down to the refuse and pillars which had been left in the mine

Jan 1, 1887

By Fred Hellmann

IT IS hardly to be doubted that the opportunity within the grasp of the mine manager for beneficent and helpful action in relation to young engineers seeking employment under him is very broad and very big. It is my experience that a manager usually has a strong inclination to help along those who have chosen the career which he has selected for himself, and to aid them and support them as their steps tread the paths which his own feet have previously followed. He has .a strong sympathy for them in their efforts, he almost yearns to shield them from the mistakes into which he himself fell, and to assist them to avoid the pit-falls of which he knows by bitter experience. Yes, this tendency and inclination is strongly developed in most managers, and they would welcome the opportunity of extending the helping hand, if they knew precisely how best this could be done.

Jan 5, 1923

By Morris Muskat

ANALYTICAL calculations have been carried out on the effect of casing perforations on the productivity of wells, and formulas have been derived for general types of perforation patterns. The numerical calculations, however, show that the resultant well productivity is essentially independent of the perforation pattern, but is determined mainly by the total perforation density. Thus, for example, for a density of three perforations per foot of casing, the well productivity will be cut to one third of that of the uncased well for a perforation radius of 1/3 in., and to approximately one half for a perforation radius of 1/4 in,, regardless of the detailed manner in which the perforations are distributed over the casing surface. The analytical theory is also extended to include wells completed with slotted liners. It is shown that the reduction in productivity due to such liners will be relatively small as compared with that due to perforated casings.

Jan 1, 1942

By Miroslaw Hajdasinski

Estimation of the economic effectiveness of industrial development projects including mining ones is generally made on the basis of the discrete model of the value changes in time, although the character of these changes is similar to the continuous model. In this paper an attempt has been undertaken to investigate the problem of the value equivalence of both models exemplified by a construction of an underground coal mine. An effort has been made to determine the errors which for different estimation criteria appear in result of the application of the discrete model. Theoretical considerations have been supplemented with practical conclusions.

Jan 1, 1977

By D. A. Crerar, R. L. P. Kleinmann, R. R. Pacelli

A bacterium, Thiobacillus ferrooxidans, is of prime importance in the formation of acid drainage from pyritic material. Above pH 4.5, T. ferrooxidans increases initial acidification; below pH 4.5, it allows acidification to continue by oxidizing Fe2 +. Below a pH of approximately 2.5, the activity of F3+ is significant and results in steady-state cycling between oxidation of pyrite by Fe3 + and bacterial oxidation of Fe2 +. Laboratory and field tests demonstrate that inhibition of T. ferrooxidans by controlled release of anionic detergents can inexpensively reduce pyrite oxidation and acid formation.

Jan 1, 1982

By Robert M. Abrams

The passage of an ore pulp through the froth flotation process results in the production, after dewatering, of a finely divided concentrate. This intermediate product must be handled to the subsequent process facilities via beit or other types of conveyors, hoppers, bins, chutes and feeders, and the like. Flotation concentrate has some difficult handling properties such as abrasiveness, sluggishness when moist, or fluidity when dry. These characteristics require the judicious selection or design of handling equipment and the careful engineering of transfer chutes. It is to the special problems which are encountered in this in-plant handling procedure that this paper is addressed. The methods which will be discussed have been developed primarily for the handling of the froth flotation concentrates of copper, lead, and taconite iron ores, but may be generalized, with appropriate modifications, to apply to other similar metallic concentrates. The controlled feeding of concentrates from bins and hoppers is covered along with some of the techniques used to transfer concentrates from one belt conveyor to another. Methods are described for unloading belt conveyors into bins or storage piles. The reclamation from storage piles is also treated.

Jan 1, 1979

By Jos D. Weeks

On the extreme fringe of' the great Appalachian coal-basin is a long narrow detached coal-field, which is, in some respects, one of the most important in the United States. This field, about 90 miles long by 2½ to 16 miles wide, extends from the southwest corner of Somerset county, Pennsylvania, through Allegany and Garrett counties, Maryland, Mineral, Grant and Tucker counties, West Virginia, into Randolph county, West Virginia. In this distance four distinct sub-districts are recognized, the Wellersburg in Pennsylvania, the Cumberland-Georges creek in Maryland, and the Elk Garden and the Upper Potomac in West Virginia. The output of coal from the whole field including steam, domestic, smithing and coking-coal of the best quality, is about 4,500,000 tons annually. It is the nearest to tide-water of all the bituminous coal-fields which supply the great coal-markets of the Northern Atlantic seaboard ;

Jan 1, 1895

By F.L. Preshidge

R. B. RATHBUN,* Salt Lake City, Utah (written discussion?).¬While the engineer should carefully weigh the merits of the various types of equipment, he must bear in mind that the object of his plant is the recovery of suspended solids, and a thing is unimportant except as it contributes to this end, other engineering principles being duly considered. The controversy regarding the use of synchronous motor-driven rectifiers by which the power for the treater is taken directly from the mains of the local power system, rather than the motor-generator rectifier giving each treater unit its own isolated electrical system, has led many to think that on the type of rectifier depends the success of .the plant. It is in fact a relatively unimportant part of the plant and represents a very small fraction of the investment; the recoveries in dust and fume are practically the same in each case. One large smelting concern has adopted the motor-generator type for all of its plants after years of experience with the synchronous-motor type. Its reasons are practically the same as those set down by Mr. Eschholz for his preference. Given more in detail they are: 1. An independent electric system prevents outside power-line conditions, like voltage fluctuations, from interfering with the operation of the Cottrell plant and eliminates the possibility of the Cottrell plant causing trouble for the power company. The latter, while not very

Jan 12, 1918

By William Buell

As used in connection with open-hearth or other high-temperature operations, "insulation" refers to a multitude of substances, natural or manufactured, that have the one principal property of preventing the flow of heat by conduction to a greater degree than refractories can prevent it, the principal properties of the latter being resistance to tem-perature and/or chemical action. The term "control" as commonly applied to the mechanization of management functions is inappropriate without qualification, for without some degree of control of every operation we could produce no steel worthy of the name. Although grouped together in this paper, insulation and control in open-hearth furnaces have little, if any, interrelationship, therefore the paper is made up of two distinct parts.

Jan 1, 1935

By J. A. M. van Liempt

SINCE the discovery, of von Laue, that a crystal forms a natural grating for X-rays, our knowledge of the structure of solids has gone forward with rapid strides. This progress is not only of purely scientific interest, but has also yielded direct technological results. One of the most valuable results is the broadening of our knowledge of the structure of pure metals and alloys. To promote these studies it is often desirable to have at our disposal pieces of metal consisting of one single crystal. As is so often the case in the natural sciences, we obtain the best results by making our earliest experiments on pure, simple materials and avoiding unnecessary complications. The Cryogen Laboratory at Leyden followed this method with much success, because the work was done at such low temperatures that the heat movement of the atoms was almost' absent. Similarly we can simplify the studies of metals by leaving out of consideration the influence of the grain boundaries and the mutual influence of the crystals by using unicrystalline instead of polycrystal-line metal. Methods of making single crystals have been scientifically studied during the past few years. Some methods were already known in the arts, but these have been improved and new methods have been developed. The methods for making metallic single crystals may be divided into the following groups: A. From the liquid state B. From the gaseous state C. Electrolytically D. By recrystallization in the solid state

Jan 1, 1927

By Charles H. Mitchell

British Columbia is enjoying a period of sustained high-level activity in all aspects and sectors of its mining industry. The total value of mineral production for 1962 was in excess of $229 million. This was the greatest total value attained for any year to date, exceeding the previous record year of 1956 by more than $40 million. It appears reasonable to expect that value of production for 1963, stimulated by increased production attained during the year, and by improved metal prices for some of the major products, will be substantially in excess of that recorded for 1962. Elsewhere in this issue appears a detailed report of prospecting and exploration activity in the Province. For the purposes of this review it is sufficient to state that the level of prospecting and exploration activity during the past several years has been greater than at any previous time and that there does not appear to be any slackening in activity or interest.

Jan 12, 1963