Search Documents

By J. F. Radavich

Many heats of steel of low carbon value have been known to produce brittle pieces of steel. The brittleness is believed to be due to the impurities located within the grain boundaries. Such brittle steels have been examined with an optical microscope to ascertain the nature and the amount of the impurities present at the grain boundaries. Due to the relatively low resolving power of the optical microscope, the impurities are not visible in fine detail. The writer obtained some sheet steel and proceeded to determine the location of the impurities and to show the application of the electron microscope to the study of grain boundaries. One sample was known to be capable of becoming embrittled, whereas another sample was believed to be much less susceptible to embrittlement. Treatment of Specimens The specimens were embrittled by annealing above the A3 point under mildly oxidizing conditions. One piece of ingot iron could not withstand a 90" bend, whereas another piece of ingot iron was not affected and could withstand a 90" bend. The brittle piece was then annealed at a high temperature in a hydrogen atmosphere. The annealed ingot iron was termed cured and could withstand a 90" bend very easily. The three specimens examined will be designated as brittle, good. and cured in the discussion that follows. Procedure The sizes of the specimens were as follows: one piece of brittle ingot iron-3/8 by 35 in.; one piece of good ingot iron-96 by 1/8 in.; one piece of cured ingot iron-36 by 54 in. The specimens were too small to be polished by hand and therefore were mounted in bakelite. The polishing procedure was carried out in the conventional manner with the use of 1/0 through 3/0 papers, and the final polish was done with alumina on a billiard cloth. The specimens were then etched in a 4 pct solution of picral in alcohol, and then they were examined through an optical microscope. An area was chosen that showed distinct grain boundaries, and an effort was made to keep near this area when pulling the replicas REPLICA TECHNIQIJE The replica technique used in the preparation of the replicas for examination under the electron microscope is described in Electron Metallography.' It consists essentially of the following steps: 1. Obtaining a suitably etched specimen. 2. Applying a swab of ethylene di-chloride on the surface. 3. Applying a formvar solution on the surface. 4. Placing a screen on any desired spot. 5. Breathing on the fornivar layer. 6. Applying scotch tape on the screen and film. 7. Pulling the film and the screen up with the Scotch tape. 8. Separating the screen from the Scotch tape. This replica technique is very similar to the one described by Harker and Shaefer. However, with the added step, the percentage of replicas removed is very much higher regardless of the length of the time from the etching of the specimen to the actual pulling of the replica. The replicas were then shadow cast with manganese at a filament height to replica distance ratio of 1 1/2:7. This produced a very high contrast replica for use in the electron microscope. One of the dificulties encountered with this study was the restricted area of the specimen. The width of the specimens was the same as that of the 200 mesh nickel supporting screen. In order to increase the effective area, the screens were cut down as shown in Fig 1. The arrow indicates the direction in which the replica was pulled. This operation made it possible to obtain a large percentage of good replicas. Fig 3 shows an electron micrograph of a brittle piece of ingot iron and a grain boundary that was polished mechanically. The surface is very rough probably due to the incomplete removal of the flowed layer by the picral etchant. The grain boundary does show evidence of impurities. It was decided to electropolish the specimens to obtain a much smoother surface than the one obtained by mechanical polishing. ELECTROPOLISHING The specimens were cut in half to expose the metal on the back side. The exposed metal had sufficient area to make good electrical contact and electropolishing was carried out easily. The conditions for electropolishing were 0.9 amp, 35 volts, and 25 sec. in an electrolyte composed of 850 cc of ethyl alcohol, 100 cc distilled water, and 50 cc of perchloric acid. The polished specimens were then etched in the 4 pct picral solution for a shorter time than was necessary for

Jan 1, 1950

By L. A. Jr. Norman

ANOTHER chapter in the history of Mother Lode mining is being written by operations in the Old Eureka mine near Sutter Creek, Amador County, California. During a two-year period (1938-1939), 85,517 tons of ore averaging 0.62 oz. gold per ton were mined and milled, as compared to the production of approximately 210,000 tons of 0.315-oz. gold ore during the preceding seven years. This is a repetition of mining history in the Mother Lode, where a period of prosperity has followed a long period of lean production. The location of this new ore in the hitherto unproductive hanging-wall greenstones and its mining and geological developments are most interesting.

Jan 1, 1939

By James T. Waber, Allen C. Larson, Karl Gschneidner, Margaret Y. Prince

The original graphical method proposed by Darken and Gurry for predicting which elements are soluble in a given element was slightly modified and was used to predict terminal solubilities in 1455 known binary combinations. it was found that the modified Darken and Gurry method had a reliability of 61.7 pct in predicting extensive solid solubility (greater than 5 at. pct) and of 84.8pct in predicting limited solid solubility (less than 5 at. pct), an over-all reliability percentage of 76.6. Using the same experimental data, it was found that using only the simple Hume-Rothery size-effect criterion was 50.1 pct reliable in predicting extensive solid solubility, only slightly better than a purely random choice. and 90.3 pct reliable for predicting limited solid solubility, an over-all reliability percentage of 67.6. THE first rational rules for determining a priori whether two metals are not freely soluble in the solid state were announced by Hume-Rothery and coworkers.1,2 These well-known rules have been accorded a special place in metallurgical literature. Since the "electronegative" and "relative valence effect" rules of Hume-Rothery were only qualitative in nature it was difficult to use them in a quantitative analysis. The next major step was made by Darken and gurry3 and apparently went unexplored for a number of years. They prepared graphs illustrating the influence of both electronegativity and size difference on the solubility of elements in silver, magnesium, and aluminum, and they drew elliptical figures, whose maximum width was ±15 pct of the solvent radius and the maximum height was ±0.4 electronegativity units. The purpose of the present paper is to assess and compare the effectiveness of using the simple size-factor and the Darken-Gurry criteria to predict which elements will be soluble and insoluble in a given solute. In 1957, waber4 prepared Darken-Gurry plots for determining the solutes that were likely to be soluble in 6 and plutonium and introduced an inner ellipse as an aid to determining which elements should be soluble to a considerable extent. As illustrated in Fig. 1, the major axis of the outer ellipse corresponded to ±0.4 electronegativity units (OD) while the minor axis corresponded to ±15 pct of the radius of the solvent phase (OB). This simultaneous "action" of the two Hume-Rothery criteria was used to indicate which elements would have little or no solubility in the host lattice, namely those elements whose points lay outside this ellipse. An inner ellipse, "centered" over the same point of the solvent was drawn with ±0.2 electronegativity units (OC) and ±8 pct (OA) as the major and minor axes. Solutes with points lying within the inner ellipse were expected to be capable of forming extensive solid solutions with the host element. Use of this method of applying the earlier Hume-Rothery criteria was moderately successful for plutonium. For 6-phase plutonium, only one element out of the eight predicted to be extensively soluble was known to be almost insoluble, and of the sixteen elements predicted to have more restricted solubility, five were known to be essentially insoluble. The success of discerning solubility in the E phase by this method was comparable. One prediction made on the basis of this analysis was that the heavier rare earth metals, such as holmium, erbium, and thulium, should be soluble in the 6 phase, whereas the lighter rare earth elements, such as lanthanum or

Jan 1, 1963

By P. L. Lavery

A numerical method to derive approximate solutions for stress intensity factors for rectilinearly anisotropic bodies without resolving to complex variable approach is presented. The method is based on the assumption that the crack opening profile can be simulated by a simple curve such as an elliptic function and a relationship is found for the stress intensity factor in terms of near tip displacements. An example solution is derived for a transversely isotropic body and the results are verified with Westergaard's stress function approach. The proposed model has a great potential for the applications to fracture mechanics of anisotropic rock materials.

Jan 1, 1984

By S. A. Braley

Drainage of acid mine water into surface streams of coal mining areas is one of the most serious problems of stream pollution, since there is no known method that completely prevents its forming and no economically feasible treatment after it has formed. The mine acid problem differs from other pollution hazards because acid production does not end with cessation of mining but actually becomes more evident when pumping is stopped. The acid problem in the Pennsylvania, Ohio, West Virginia, and Kentucky bituminous coal areas of the U. S. began with the first operation in 1761, and the volume of acid discharge today is largely the cumulative result of years of mining. Provided they lie above the drainage area, the oldest mines, now long abandoned, are almost without exception producing acid in the same manner as those now operating or recently abandoned.

Mar 1, 1956

By Ernest N. Patty

Placer gold-bearing gravels of interior Alaska and the Yukon are, for the most part, permanently frozen, and are described as permafrost. The first step in preparing these gravels for dredging is to strip by bulldozer the surface layer of tundra, brush, and scrub timber, and to expose the ebony colored surface of the frozen mud at the grass roots. This mud varies from a frozen, muddy ooze to a sandy silt and locally may contain layers of peat. The whole mass is intercalated with ice dikes and lenses. The thickness will vary from a few feet up to 100 ft, depending upon local conditions. A freshly exposed surface will thaw to a depth of 4 in. per day during the summer season. Common practice is to expose a large surface of this mud to the sun and each day's thaw is then swept off by water and carried away in suspension.

Jan 1, 1951

By Frederick Laist

(Butte Meeting, August, 1913.) WHILE remodeling No. 1 section of the concentrator at the Washoe Reduction Works of the Anaconda Copper Mining Co. during the summer of 1912, for the purpose of ascertaining what additional metal recoveries could be made by improvements in concentration practice which had been developed by the staff of the Boston & Montana Reduction Department, at Great Falls, it was deemed advisable to carry on some experiments on the treatment of the regular mill tailings by roasting and leaching, to see whether the losses of metal values might not be still further decreased. In the course of these experiments about 5,000 tons of tailings were roasted, and of the resulting calcine about 200 tons were leached. The results were so satisfactory that it was decided to continue the work on a larger scale, particularly as regards the leaching end of the process, and construction work on an 80-ton roasting and leaching plant was accordingly commenced during the latter part of February, 1913, and is being pushed as rapidly as possible. 80-Ton Leaching Plant. This plant will consist of one 20-ft. roasting furnace of the MacDougall type, specially adapted to the work of roasting for leaching; two leaching tanks, .32 ft. in diameter by 12 ft, deep, together with the necessary solution tanks, air lifts, precipitating launders, etc. It has been decided to precipitate the copper from solution on scrap iron, so as not to hamper the roasting and leaching departments by any weakness that might develop in the precipitating department. It is, however, the intention to experiment with a number of different methods of precipitation ; for example, by electrolysis and by hydrogen sulphide.

Jan 7, 1913

By William B. Plank

Mineral engineering student enrollment in U. S. and Canadian schools for 1955-1956 is 11,408, an increase of 11 pct more than last year. The undergraduate and graduate engineering students in both countries number 251,765, or 13 pct more than last year. These figures have been released by the American Society for Engineering Education. The largest increase in the undergraduate mineral engineering group in the U. S. is in ceramic engineering, with 676 students, or 31 pct more than last year. The next largest increase is in mining which shows a gain of 13.5 pct, compared with a gain of 13.1 pct in the total undergraduate enrollment in all engineering schools approved by the Engineers' Council for Professional Development. This figure is 190,355, which approaches the prewar figure. Metallurgical undergraduates increased 13 pct; geological, 5 pct; and petroleum, 2.5 pct. This year the figures for geophysics are combined with those for geological engineering, making a total of 1610 undergraduates, of which the geophysicists comprise about one seventh.

Apr 1, 1956

By L. D. Jaffe, D. C. Buffum

EARLY papers1-' reported that temper brittleness is influenced by microstructure. This conclusion was based on room temperature impact tests, the inadequacy of which has been pointed out. Pellini and Queneau7 measured impact energy absorption at —80O to +25oC for several microstructures. On the basis of the shift, associated with temper brittleness, in the energy vs testing temperature curve they concluded that tempered martensite is somewhat more susceptible to temper brittleness than is tempered pearlite. The range of temperatures was insufficient to give complete curves covering the transition from tough to brittle behavior, so it is difficult to evaluate quantitatively the shift for the different microstructures. Also, the smaller shift of pearlite might be attributed to its already being temper embrittled at its temperature of formation. Accordingly, blanks 2 3/16 in. long were cut from a heat of SAE 3140 hot rolled steel barstock, 5/8 in. diameter, on which other work has been reported? A set of blanks was austenitized 1 hr at 900°c, water-quenched, tempered 16 hr at 675oC, and water-quenched, giving a microstructure of 100 pct

Jan 1, 1954

By John Sherbourne

Much valuable scientific research has been performed in recent years on the subject of phase behavior of hydrocarbons. ? 1-11 Engineers employed in petroleum production are interesting themselves in this work as well as in methods of applying the fundamental data available to the solution of their various problems. Recently a number of papers have been published in which applica-tions of phase behavior have been made to specific cases pertaining to critical phenomena.)12-16 Little effort, however, has been made in the literature to show the relation between changes occurring in the critical region and the more common phase behavior, therefore it is believed that a presentation of the fundamentals of phase behavior with reference to hydrocarbons is timely. Study of phase behavior is not new. In the metallurgical field, knowledge of heterogeneous equilibria has advanced tremendously, particularly with reference to solid-solid and solid-liquid behavior. Much is known about vapor-liquid equilibria too, but few engineers are familiar with this subject. ?

Jan 1, 1940

By C. H. G. Bushell, M. Malnarich

Reagent control in flotation is more an art than a science. Operators vary the amount of re- agents used according to the metallurgy obtained. The amount of collector may be increased, for example, if tailings losses are high and decreased if concentrate grades are low. Often control decisions are based on only one assay, such as the tailings analysis by microscopic or quick assaying techniques. This method of control has given reasonably satisfactory results but is clearly far from perfect. No adjustment in reagent addition can be made until information is received that metallurgy has deteriorated, that is, until the optimum time for adjustment has already passed. The first adjustment probably will be an overcorrection or an undercorrection, and time will be required to establish the best new addition rates. The seriousness of the problem depends on variability of the ore. In ore of continually shifting composition and complexity, mill results will shift back and forth from excessively high concentrate grades and high tailings losses to excessively low concentrate grades and low tailings losses. Economic incentive for improved control also increases with increasing size of mill. Even a small improvement in percentage recovery in a large mill pays for expensive control equipment.

Jul 1, 1956

By Edward Sayre

IN shaft sinking for coal mines, the cost item greatly influences the method adopted. This holds true especially when soft material must be traversed. The average life of a coal mine is short. This is clue either to the limited area of the coal basin or to the great expense of maintenance and haulage underground when the entries are extended a considerable distance from the hoisting shaft. Therefore, the engineer in opening a coal mine is confronted with the fact that the cost must be kept within certain bounds else the venture will prove unprofitable. For this reason he may be prohibited from adopting certain safe, but expensive, methods that are used in sinking caissons for foundations, driving transportation tunnels, or other work of permanent construction. A common method of sinking through difficult ground employs the aid of a steel shoe pushed ahead of the shaft timbers. Another is the drop-shaft method. These two methods were used in sinking the main shaft and the air shaft of the Eagle No. 3 mine, at Des Moines, Ia., and the following data show the relative success and cost of the two methods of sinking under the same conditions. A drill log of the material to be penetrated was as follows (see Plate 1, Fig. .1)

Jan 9, 1916

The Secretary of the Treasury, acting through the National War Savings Committee, soliciting the support of patriotic associations in America in the sale of War Savings Stamps, has addressed the following letter to the President of the Institute: It is particularly desirable to have you urge the members of your association to give their assistance wholeheartedly, and to this end we urgently request that you write a letter to each of your members, outlining the aims of this campaign. That you may more easily draft your letter, we mention a few things in which your members could render a special service. Agencies and Sales Stations.-We desire immediately to establish several hundred thousand agencies and sales stations. It is as easy to sell a War Savings Stamp as it is in ordinary postage stamp, and we have launched a great drive to establish sales stations everywhere. The plan is simplicity itself! Your town, city, county or State Director can furnish you with supplies, posters and publicity matter. You can get the stamps from your post office or bank. Such stations should be at every pay window of manufacturing, industrial and mercantile establishments, and at every retail counter in the country. These stamps should be the easiest bought merchandise in the world, and when these agencies are established this end will have been accom-plished. Therefore, please lay extra pressure on the thought of immediately establishing these sales stations.

Jan 3, 1918

By Jan M. Mutmansky

The primary purpose of this presentation is to analyze the strategies available to an operator using either stripping or stripping and subsequent punch mining on a given coal property. The initial concern is the formulation of a mathematical model, which allows an operator to determine and utilize the particular highwall height, which will maximize : (1) Total profit or (2) Profit per unit of operating time. The analysis centers on the relative costs and recoveries involved in a typical coal seam amenable to stripping, augering, and punch mining. The model defines the point to which the high-recovery stripping operation with increasing overburden removal and reclamation costs should proceed before the low-recovery augering and punch mining methods are employed so that the desired objective is achieved. Examples are presented, which exhibit the use of the model on typical operations. Present mining methods as practiced in the Eastern United States are examined in the light of the results. Recommendations for improving present strategies are made and the resulting economic ramifications are analyzed. Particular attention is given to the stripping ratios presently used and recommendations for improving present mining practice are presented. Implications of these recommendations to the design of strip mining equipment are discussed.

Jan 1, 1977

By F. S. Sinnatt

This paper is the outcome of an extended investigation carried out in association with Dr. L. Slater. The inquiry had been continued in various directions and a number of results are quoted from an investigation recently completed by S. H. Jenkins. In projecting the work some five years ago, the author had in view a general attack on the problem of the spontaneous combustion of coal from an angle that had received little attention. The basic idea was to obtain a "slow motion study" of the active combustion of coal. This included an examination of the conditions prevailing in a mass of coal at the moment when active combustion ceases. It was thought that, if the factors governing the extinction of combustion in coal could be definitely established, it might offer an explanation of the manner in which the spontaneous combustion of coal originates. The inquiry arose from a detailed study of the properties of fusain that the author began in 1918. Fusain seemed to possess characteristics quite distinct from the coal with which it was associated, for if it were collected into a heap and one portion were heated by a small flame the combustion would traverse the whole mass. This combustion was not accompanied by smoke and passed slowly through the heap of material. Later, it was found that coals, including anthracites, would behave in a similar manner provided they were in the form of powder and that the particles were smaller than a certain size. The limiting size of particles is a definite characteristic of the coals investigated. In view of the fact that fusain exists with coal in a state that enables it to undergo this particular form of combustion, it must be assumed, sometimes, to play a definite part in the spontaneous combustion of coal in the goaf (waste). Tables 1 and 2 contain the analyses of samples of dust collected from a mine and from a dust collector. Some idea of the degree of fineness of the particles of fusain may be obtained from a study of the analyses of the dust from the dust collector; 80 per cent. of the dust would pass through a 200-mesh screen while the fusain was concentrated in the finest dust. The material that passed through a 90-mesh screen contained 54 per cent. of fusain while that between a 30- and a 90-mesh only con-

Jan 1, 1925

By F. P. Dewey

Recent discussions have furnished to the members of the Institute much information concerning aluminum and its applications. The present paper will be devoted almost entirely to the description of a process by which the metal is produced in the form of alloys. The characters which especially distinguish the Heroult process consist in electrolyzing a mass of molten alumina (Al2O3), and at the same time alloying the separated aluminum with a heavy metal, the heat necessary for the fusion of both the alumina and the alloying metal being supplied by the direct passage through the molten Al2 0, of an electric current of high amperage and low voltage. The process has been in active operation at Neuhausen in Switzerland for about two years. It is also in active operation at Froges in southern France. Both these locations were selected for this purpose on account of the presence of large and desirable water-powers. The apparatus consists of a carbon containing-vessel, which may be a single crucible for small operations, or may be built up of slabs or blocks of carbon for large and industrial operations. When built up of slabs or blocks, the whole is surrounded by an iron casing. In the earlier crucibles this iron casing was cast around the carbon, in order to secure close electrical contact. This, however, has been found unnecessary; and in the later crucibles the casings consist of plates bolted together, while pulverized carbon is packed between the carbon blocks and the iron. Electric conductors are united direct to this iron casing, and the current passes from this through the carbon lining to the interior of the crucible. By this

Jan 1, 1890

By Alan Morris

THE investigation of the hot-working properties of metals and alloys furnishes a problem which has been attacked in many ways. Tensile, impact and hardness tests on heated specimens have furnished interesting data, but in most cases either the tests are difficult to make or the results hard to translate into terms of practical value. Some investigators have used the drop hammer to advantage. It furnishes a rapid and simple method of comparing the plasticity of metals at elevated temperatures. The indications obtained by its use are of value only in so far as their significance is understood and they can be intelligently used to predict the behavior of a given metal under given hot-working conditions. The work reported here was undertaken not only to add-something to the existing volume of such data but also to contribute to our understanding of the results. Doerinckel and Trockels1 used cylindrical specimens and determined the work required to reduce the specimen to one-half the original height. Ellis2 studied the effect of constitution on the malleability of steel at high temperature. His method and that of Kent3 were similar to the one used in the present work. The tests described by Kent were made on samples of tin, zinc, aluminum, copper, lead, 70:30 and 60:40 brasses, with and without a small quantity of lead. He concluded that the test would "indicate whether a material can be forged at a given temperature without cracking." This interpretation must be used with caution. While it is probably true within limits, one must consider the severity of the forging operation. Again, it will not apply strictly to forms of hot working other than forging. For instance, an alloy running 61.0 per cent. copper, 3.25 per cent. lead, remainder zinc, will crack badly in the test, yet it is extruded commercially. When the possibility of hot-working a new alloy is being considered a study of its drop-hammer test should help

Jan 1, 1931

Jan 1, 1939

By L. Sturkey

Quantitative X-ray diffraction studies of the precipitation of thorium in a Mg + 3.3 Th + 0.51 Zr alloy (HK31A) in both the as-cast and cold-worked states show that the precipitation may be described by f = 1 - e(t/T)1/2 over most of the aging period. The effects of cold work and temperature changes are determined. The precipitation of tile equilibrium Mg-Th compotund is Preceded by the formation of a transition phase of higher thorium content, with the cowposition Mg2Th and with a Laves-phase structure. Thorium-containing alloys of magnesium have assumed considerable commercial importance, especially for applications requiring exposures to temperatures greater than 500°F for appreciable lengths of time. The principal commercial wrought alloys in this system are HK31A, containing nominally 3 pet by weight thorium and about 0.7 pet by weight zirconium: and HM21A. containing 2 pet by weight thorium and 1 pet by weight manganese. These two alloys retain a high level of properties even after exposures of 100 hr at 600°F, while the more common alloys containing aluminum and zinc are badly overaged by these conditions. Therefore, in order to obtain some insight into the mechanism by which thorium produces high temperature stability in these wrought alloys, it seems desirable to investi- gate the effect of temperature and mechanical working on the precipitation processes involving thorium. Since the scattering power of a thorium atom for CuKa X-ray radiation is about ten times that for a magnesium atom, the magnesium alloys containing about 3 pet by weight thorium are ideal for quantitative measurements by X-ray diffraction of the amount of Mg-Th compound present at any time. Such quantitative measurements should be of theoretical importance in the study of the effects of time, temperature, and deformation on precipitation and precipitation hardening. Of the two commercial alloys, HM21A and HK31A, the latter is certainly the most suitable for study: In the Mg-Th-Zr2 system, only Mg-Th compounds need be considered, since no ternary compounds or binary Th-Zr3 and Mg-Zr4 compounds exist. The Zr is added to this alloy as a grain refining agent and probably plays a secondary role in precipitation. On the other hand. thorium and manganese form many

Jan 1, 1961

Jan 1, 1943