Search Documents

By J. S. Brown, A. G. Guy

With the exception of the work of Tammann and Hartmann,1 no published information has been found on the structural changes produced in eutectic structures as the result of heating following plastic deformation. In part this lack of information may be due to the fact that many eutectic structures contain an intermetallic compound as a prominent phase, and as a consequence have been considered to be unworkable. For example, Tammann and Hartmann were able to obtain useful data only on those alloys that they could greatly reduce in thickness by cold rolling. This restriction placed on the investigation of alloys containing intermetallic compounds has been largely removed by the work of Savitskii2 which showed that large deformations of such alloys can be produced by relatively slow compression at temperatures near the melting range. It was possible, therefore, to carry out the present work on a range of binary eutectics including one composed of two intermetallic compounds. The essential results obtained on the alloy systems studied are illustrated by the Pb-Mg eutectic containing 33.2 pct Mg, Fig 1. The cast structure, Fig la, was obtained by melting together magnesium of 99.8 pct purity and chemically pure test lead, casting into a heated, small steel mold, and furnace cooling in the mold from about the eutectic temperature. The fairly coarse eutectic structure thus obtained was too brittle to work at room temperature without cracking. Fig 16 shows the worked structure obtained by compressing a 1/2-in. cube 70 pct in about 15 sec at 550°F and then water quenching. The pronounced changes in the distribution of the two phases produced by heating the worked alloy at 850°F for 1 hr are shown in Fig lc. Recrystallization of both phases appears to have taken place, and the mechanical properties of the cast alloy must have been significantly changed by the working and heat treatment. Similar results were obtained with the Mg-59.5 pet Bi, Mg-36.4 pet Sn, Mg-65.4 pet Cu, and Bi-40 pet Cd eutectics, only the last of which could be worked at room temperature. Tammann and Hartmann reported a thickening and shortening of the needles of the eutectics which they heated about 10°C below the melting range for 1 hr after drastic cold rolling. They found the following eutectics, given the indicated amounts of reduc- tion, to have a granular structure after heat treatment: Sn-9 pet Zn (98 pet); Cd-82.5 pet Pb (60 pet); and Bi-43.5 pet Pb (90 pet). On the other hand the alloy Al-11.7 pet Si (60 pet) showed no change after heating. Tammann and Hartmann observed a distinct shrinking of the needles in unworked eutectics subjected to heat-treatment. In the present work inappreciable change in the eutectic structure was found on heating undeformed alloys. In summary, it appears that eutectic structures can be recrystallized into a "spheroidized" condition by heating near the eutectic temperature after severe deformation. If the eutectic contains one or more brittle phases the necessary deformation can be accomplished by pressing at high temperatures. It is reasonable to expect that this tendency towards equiaxed grains from the plate- or needle-like eutectic structure should be general since the energy relations and mode of growth in recrystallization are so different from those that hold for eutectic crystallization. References 1. G. Tammann and H. Hartmann: Ztsch. Melallkunde (1937) 29, 141-144. 2. E. M. Savitskii: Doklady Akad. Nauk S.S.S.R. (1940) 62, 349-351. Abstr. in Melal Prog. (July, 1949) 56, 126, 128.

Jan 1, 1950

By P. Nelson, K. L. Gunsallus, A. R. Ingraffea, J. F. Beech

INTRODUCTION Fracture toughness, KIC, is an intrinsic material property and is a measure of the energy required to create new surface area in a material. Fracture toughness measurements can be made for a wide range of rock types (Ouchterlony, 1980). As a measure of energy of comminution, fracture toughness might be used for more sensitive predictions of Tunnel Boring Machine (TRM) performance than are possible with other index measures in current use. This paper describes part of an ongoing, comprehensive, analytical/experimental program aimed at evaluation of KIC in such a role. The program includes efforts to: 1. Provide a firm analytical basis for a test specimen geometry: the core-derived short-rod. 2. Develop simple, inexpensive testing equipment and techniques. 3. Evaluate the accuracy of the above by testing rock and other materials and comparing the measured fracture toughness with those obtained by other methods. 4. Measure fracture toughness of a substantial number of different rocks from three ongoing TBM projects. 5. Compare fracture toughness results with other strength measures. 6. Compare all test results with observed TBM performance in the three projects. Presented here are summaries of all but the last of these efforts. Comparative evaluation of KIC as a more senstive rock property for TBM performance prediction will be the subject of the oral presentation and a subsequent paper.

Jan 1, 1982

INTRODUCTION TO COMPOSITING Individual drill hole samples may vary greatly in size, length, and weight. The sample interval may represent any convenient unit of hole length, and is usually related to the type of drill being used to obtain the sample. Depending upon the type of mineral deposit, it is desirable to group the individual sample values into composite weighted values representative of some particular zone or volume of the ore body. For example, values of several sequential samples of diamond drill core 3 m (10 ft) in length may be grouped together to represent a 12-m (40-ft) sample value over one bench height. On the other hand, several individual sample values taken across the thickness of a stratiform deposit or a vein zone may be weighted together to represent the value of the total thickness at the point of intersection. The choice of composite intervals is usually dictated by the type of mineral deposit and the mining method selected to produce the mineral. The techniques of weighting values from various lengths of samples into a composite value has already been discussed briefly in Chapter 3. Further examples of determining weighted composite values will be given in the following discussion on compositing for various types of mineral deposits. SAMPLE VALUE COMPOSITES AND TYPES OF MINERAL DEPOSITS There are many kinds of mineral deposits, each of which will require special treatment of sample data to obtain the best composite intervals for evaluating the deposit. It cannot always be known before hand what the optimum composite interval will be. Such composite intervals may properly be determined by geologic factors that are often unknown prior [ ]

Jan 1, 1980

By Heinrich Ries

The clay-resources of Colorado are but little known, for the reason that little has been published concerning them, and also on account of the hitherto small demand for clay products in the Rocky Mountain region. At the present day the wares manufactured from clay which are used in Colorado include common and pressed brick, terracotta, sewer-pipe, pottery and refractory articles. Most of these are brought from a considerable distance; but with an increasing demand for such goods in the West and a better knowledge of the available materials, there should be considerable expansion in the clay-working industry of Colorado in the future. The notes here presented are an abstract of those collected by the writer in October, 1896, in a reconnaissance of the clay-bearing formations of Colorado. Clay-bearing Formations. We may roughly divide the clay-bearing formations of Colorado into three groups : 1. Loess and alluvial deposits. 2. Jura-Trias and Cretaceous clays. 3. Tertiary clays. . The loess forms an extensive deposit of large area, though not very thick, extending from north to south across the State, and eastward from the foot-hills. It is generally a very sandy clay, with little plasticity, and is underlain by a gravelly stratum, which determines the workable depth. Clay similar to the loess is found underlying the river terraces in many of the broader valleys, such as those of the Arkansas, Grand River, etc. The Mesozoic formations extend along the eastern edge of the Rocky Mountains, and also occur in some of the deeper valleys tributary to the foot-hill belt. They consist of a great series of interbedded shales, sandstones and limestones of Jura-

Jan 1, 1898

By S. Wiederhorn

The energy and force of interaction between a crack and a slip band have been calculated. When the distance between the crack and the slip band is greater than the dislocation spacing of- the slip band, the force on the cgrack is perpendicular to the slip band. The energy needed to propagate a crack against this force can be lawe enough to pevmit crack propagation parallel to noncleavage planes. SEVERAL recent experiments have demonstrated the occurrence of crack-slip band interaction in ionic crystals having a NaC1-type structure. Stokes, Johnston, and Lil have studied the nucleation and growth of cracks in MgO. From their observations, they conclude that slip bands have the ability to halt and stabilize cleavage crack nuclei. Gilman2 has shown that a crack, propagating along a (100) cleavage plane in a previously deformed LiF crystal, tends, at certain points within the crystal, to switch to (110) planes. He reasons that plastic deformation reduces the cohesive energy of the (110) planes below that of the (1130) planes, making possible (110) crack propagation. Keh3 has demonstrated that when indentations are made in MgO, crkcks form along (110) planes at the indentations. Gilman2 attributes the formation of these cracks to plastic cieformation. There is some doubt as to the formation of cracks on (110) planes. Kuznetsov4 in his discussion of crack propagation in rock salt, shows that splitting along (110) planes requires 1.76 times as much energy as splitting along a stepped (100) surface. Therefore, the observed (110) cracking in LiF and

Jan 1, 1962

By C. A. Wert

THE solid solubility of cementite in a-iron has been investigated a number of times and there is now general agreement on the solubility of about 0.018 wt pct at the eutectoid temperature, 720°C. With decreasing temperature, the solubility falls off so rapidly and to such a low value that no data obtained by standard metallurgical methods are available below 500°C. Using a new technique, however, Dijkstral has obtained apparently accurate solubilities down to 400°C; which data agree well with previously measured solubilities in the 600" to 700°C temperature range.' The present paper has in part the purpose of extending his work to still lower temperatures. Earlier work of Low and Gensamer3 on iron has established that the presence of a relatively small amount of carbon can play a tremendous role in affecting the mechanical properties. In particular they found that the yield point remained high as they reduced the amount of carbon in the iron; the yield point dropped only after the carbon content had fallen to something less than 0.003 wt pct, the point where their carbon analysis failed. It seemed desirable to the present author to see if some means could not be found to extend this part of their work. This investigation has then the additional purpose to determine the range of carbon concentration in which the major change occurs. Solubility The method used in the present work to measure small percentages of carbon in a-iron utilizes internal friction. Since this method may not be fa-miliar to the reader, the following explanation will be given (a part of this procedure is from unpublished results of Dijkstra): It is known that the internal friction associated with the diffusion of

Jan 1, 1951

H. G. DAVIS, * Wilkes-Barre, Pa. (written discussion ? ).-The only practical method of testing mine air for gas, until recent years, was by the effect of the gas on the flame of the ordinary Davey Lamp, and it is quite surprising how nearly the correct percentage of gas can be deter-mined by many men by observing the behavior of the safety-lamp flame in the different mixtures. Mine foremen frequently guess the percentage of gas to within 0.1 per cent., making certain allowances to cover the dust-laden atmosphere, in which the test was made. It is not meant by this that anthracite dust is explosive, but that its properties increase the length of a fuel cap on an ordinary oil-burning lamp, which, as Prof. -Young contends, increases in height with the proportion of gas and in-creased temperature. Naphtha or benzine-burning lamps have a hotter flame, and, there-fore, are more sensitive so that a smaller percentage of gas can be detected. Some of the fire bosses in this region some years ago preferred the Koehler lamp, while others did not care to use it in their morning examinations. In 1911, when the experimental mine of the Bureau of Mines at Bruce-ton, Pa., was being prepared to be exploded, a large number of mining men went through it to examine the entries, which were lighted by electricity. While so doing, they saw in the face-return-airway a Koehler or Wolfe lamp, that seemed to he burning with difficulty. An investigation showed that the lamp had been filled to overflowing with naphtha and was generating this surplus gas. This shows how easily we can be

Jan 11, 1919

By S. L. Sass

DURING an electron microscope study of the w phase in zirconium-base alloys,1 a stereographic technique was devised which allows the synthesis of high energy electron diffraction patterns from a single crystal containing several variants of a second phase. The technique will be described using as an example the w phase which forms in a bcc matrix. The w phase was suggested by Silcock et al.2 and Bagaryatskii et al.3 to have a hexagonal structure with (0001)111(111)^, [001]B//[110]B* *The subscripts B and 1 are used to refer to the bcc phase and one particular orientation of the w phase, respectively. and with cell parameters aw = v2aB, where a^ is the lattice parameter of the bcc struc-ture. Since there are four <lll>B directions there should be four orientations of the w phase. In approaching this problem the question to be answered is, "What reciprocal lattice vectors from the B phase and the four w variants lie in the particular reciprocal lattice plane of interest?" One may restate the question in the form, "What plane normals from the B phase and the four w variants lie in the particular reciprocal lattice plane of interest?" The question is answered and the desired diffraction patterns are plotted using the following stereographic technique. Knowing the cw/aw ratio (=0.613 for the as-quenched form of the w phase), a stereographic projection of plane normals from one w variant can be constructed relative to a cubic projection using the above orientation relations, with the direction of the projection along the [001]B direction, Fig. 1. Let us now synthesize the diffraction pattern observed by looking along

Jan 1, 1970

By Frank Rieber

THE study of earthquakes long ago developed the fact that by studying the travel times of the various groups of waves from the same earthquake, as received on seismographs at varying distances, major discon-tinuities in the earth&apos;s crust could be reasonably well defined. Using this original discovery, and adapting the mathematical methods originally devised in seis-mology for determining the depth below the surface at which such discontinuities occur, other investigators were able to develop a new branch of seismology which promises to be extremely useful in extending the boun-daries of our information oil local conditions below the earth&apos;s surface. As an outstanding example of the applications of this work, we have the so-called "seismo-graph" exploration of the Gulf Coastal region, which has resulted in the discovery of a large number of salt domes, from many of which oil fields may be developed. The original seismological investigations, from which different major discontinuities in the earth&apos;s crust were deduced, as well as these later successful experiments in finding salt-dome structures, involve relatively simple problems. In each case we are dealing with surface materials in which elastic waves will be propagated with a fairly definite velocity. Under this material we have something very different, in which the elastic waves will be propagated with a much higher velocity. The transition from one medium to another is like-wise relatively abrupt. For example, in. the Gulf Coastal region the sedimentary formations have a velocity of 6000 or 7000 ft. per sec., while the velocity of elastic waves in the cap rock of a salt dome" may exceed 15,000 ft. per sec. Under such conditions, de-lineation of the formation is a relatively simple matter, and, furthermore, there is very little opportunity for ambiguous results.

Jan 9, 1928

By Gilbert Thiessen

The use of a pneumatic process for removing fine material (usually less than 48-mesh) is increasing in the preparation of stoker-size coal. The fine material, produced as a byproduct, is known as dedusting-plant dust. Since fusain is the most friable ingredient in bituminous coal (it may readily be rubbed to an impalpable powder with the fingers), it tends to accumulate in this byproduct. While studying the properties of cokes produced by blending Illinois coals with other materials, considerable quantities of fusain were required. Dedusting-plant dust suggested itself as a convenient supply. It became necessary, therefore, to determine how much fusain was contained in a measured sample of dust, how the fusain was distributed with respect to size and specific gravity in the sample, and whether or not it would be feasible or desirable further to concentrate or to recover the fusain from the dust before using it in the blends to be coked. The results obtained indicate the possibilities of production of a high-fusain material. Previous Work Lehmann and Stach have developed a processl,2 for separation of banded bituminous coals into their band ingredients by impact pulverization followed by screening or air separation. They found, as might be expected, that the fusain was concentrated in the very fine material. Prockat and Raute3 examined samples from dedusting plants operating in the Ruhr. They separated the dust into various screen sizes and determined the composition of each of these sizes in terms of the banded ingredients of the original coal. In the dusts examined by them, the finest material was always high in fusain, and most of the fusain contained in the original samples could be recovered from this fraction.

Jan 1, 1936

By Gilbert Thiessen

The use of a pneumatic process for removing fine material (usually less than 48-mesh) is increasing in the preparation of stoker-size coal. The fine material, produced as a byproduct, is known as dedusting-plant dust. Since fusain is the most friable ingredient in bituminous coal (it may readily be rubbed to an impalpable powder with the fingers), it tends to accumulate in this byproduct. While studying the properties of cokes produced by blending Illinois coals with other materials, considerable quantities of fusain were required. Dedusting-plant dust suggested itself as a convenient supply. It became necessary, therefore, to determine how much fusain was contained in a measured sample of dust, how the fusain was distributed with respect to size and specific gravity in the sample, and whether or not it would be feasible or desirable further to concentrate or to recover the fusain from the dust before using it in the blends to be coked. The results obtained indicate the possibilities of production of a high-fusain material. Previous Work Lehmann and Stach have developed a processl,2 for separation of banded bituminous coals into their band ingredients by impact pulverization followed by screening or air separation. They found, as might be expected, that the fusain was concentrated in the very fine material. Prockat and Raute3 examined samples from dedusting plants operating in the Ruhr. They separated the dust into various screen sizes and determined the composition of each of these sizes in terms of the banded ingredients of the original coal. In the dusts examined by them, the finest material was always high in fusain, and most of the fusain contained in the original samples could be recovered from this fraction.

Jan 1, 1936

By Cornelius Kelley

VOLUMES have been written about the organizing genius of American industrialists. American methods of production are being studied by the manufacturers of other nations to ascertain the prac-ticability to foreign adaptation. Mass production and the mechanization of industry have become terms of popular understanding and significance. Our people think, act and talk in terms of economic nomenclature. Under these circumstances is it not a matter of supreme importance that Americans themselves should make an analysis of their own situation? National supremacy has been but a transitory event. Wealth has had no fixed abode, and commerce has followed no permanently established route. One hundred and fifty years, viewed from the abstract idea of time, is but a moment in the fact of continuous or successive existence, yet it measures. the cycle that has witnessed the growth of America from a struggling embryonic union of thirteen colonies estab-lished along the Atlantic seaboard to the nation of un-rivalled proportions, vast wealth, huge enterprises and productive energy that now exists beneath the protec-tion of and renders allegiance to the flag that but then had been created. To appreciate fully the significance of what has occurred, it is necessary that there should bee an understanding of the basic factors that have con-tributed so largely to the realization of our present situation. Among the most important were: First, the establishment of a government that was founded upon the principle of affording the widest pos-sible opportunity for individual effort and accom-plishment. Second, there existed a virgin territory of vast extent, endowed by nature with elements of potential wealth far exceeding that possessed by any other like area upon the globe.

Jan 8, 1928

By Strathmore R. B. Cooke, Iwao Iwasaki, Hyung Sup Choi

The effect of temperature as a parameter in ore flotation has not been systematically studied, although for some ores it has been known for many years that selectivity and grade of concentrates can be improved by conditioning or flotation at moderately or substantially elevated temperatures. In 1934 Coghill and Clemmer&apos; stated that "elevated temperature seems to make hard water more tolerable" in soap flotation, and a cursory examination of the literature indicates that some earlier investigators were aware of beneficial results obtained by floating above room or mill-water temperatures. Tartaron,&apos; Mitchell et al.,3 and particularly Hamilton et al." have shown that high pulp temperatures give high recovery and selectivity in soap flotation of fluorite from a variety of gangue minerals. As a result of the work of these and of other investigators, high-temperature flotation has been successfully applied to industrial flotation of fluorite. Falconer" stated: "The use of high temperature conditioning (above 35°C and preferably above 60°C) in connection with the soap flotation of nonsulphide ores, as covered in B. Kalinowski&apos;s French Patent No. 847,- 215, Dec. 7, 1938, is claimed to provide more intense activation, better separation of values from gangue, and reduction in quantity of reagents." The various investigations quoted above clearly demonstrate the improvements to be realized by increasing the temperature at which fluorite is floated, and it is surprising that little or no information has been published on systematic investigation of the same method as applied to other ores.

Jan 5, 1960

By P. D. Wilson

The genesis of some orebodies has been explained by the mingling and chemical interaction of water solutions of different compositions and the consequent precipitation of the mineral load of one or both solutions at their confluence. While this process can be proved in the laboratory, rarely can a positive demonstration be found in nature, for the conditions at the time an ore deposit is being worked are usually entircly differcnt from those that existed when the orebody was formed. For this reason, the present deposition of copper carbonate in the southern end of the Briggs mine of the Calumet and Arizona Mining Co. near Bisbce, Ariz., is of great interest. The developed orebodies in the Calumet and Arizona mines are roughly confined to two broad parallel zones separated at the north by a wedge of Copper Queen ground and at the south by an undeveloped block of Calumet and Arizona ground about 2000 ft. (610 m.) wide. The more westerly zone includes the Irish Mag, Oliver, P. and D., and Cole mines, none of which has been operated since 1919. Much of the water from this division is carried from the 1400-ft., or bottom, level at the southern end of the Cole mine in a long water drift through the undeveloped block to the 1300-ft. level of the Briggs mine at the southern end of the more easterly zone. Most of this water comes originally from outlying areas in the P. and D. mine, passing through parts of the lower. levels of the Cole mine, which are heavily mineralized with iron and copper sulfides. This sulfide zone has been opened up and slowly oxidizing for years. Originally a pure, potable water, the analyses of which are shown under A- in Tables 1 and 2, on its way through the mineralized area in the Cole mine it gathers copper, calcium, magnesium, iron, and aluminum sulfates, a load of dissolved mineral salts almost four times as great as that which it formerly carried; analyses B

Jan 1, 1923

By R. G. Baughman

With the constantly increasing sales competition, coal to be sold today must meet the test of quality in every respect. The producers must be able to make all marketable sizes that will meet such general requirements as follows: 1. Ash content must be consistently low, depending upon the use to be made of the coal. 2. Sulfur content must be controlled accurately according to requirements. 3. All sizes must be positively free from visible impurities. 4. Free moisture of washed sizes must be reduced to a minimum. 5. The freezing of wet coal in cars must be prevented. 6. The percentage of fines in small mixed sizes must be controlled to give the uniform and proper combustion when used on various types of automatic stokers. 7. The undersize particles or degradation caused by handling must be kept to an absolute minimum in all sizes loaded. Many difficulties may be met in bringing any particular coal to meet these quality requirements, because the extent to which the quality of a coal may be controlled is determined largely by its physical characteristics. Preparation of an Impure Coal Bed The application of modern and scientific methods in the controlled preparation of bituminous coal from a bed in the mid-western field will illustrate the results that can be accomplished by adequate preparation: The bed referred to contains coal inherently excellent as to low ash and other desirable characteristics; in fact, the coal itself is one of the best in the field. It is, however, divided into four layers by dirt bands of soft shale 1 to 2 in. thick. It also contains much sulfur in the form of sulfur lenses and laminated sheets. Horsebacks or rolls varying from 6 in. to 12 ft. in width are encountered in the mining of the bed and heretofore have rendered it practically unworkable. The mines operating in this

Jan 1, 1931

By P. D. Wilson

The genesis of some orebodies has been explained by the mingling and chemical interaction of water solutions of different compositions and the consequent precipitation of the mineral load of one or both solutions at their confluence. While this process can be proved in the laboratory, rarely can a positive demonstration be found in nature, for the conditions at the time an ore deposit is being worked are usually entircly differcnt from those that existed when the orebody was formed. For this reason, the present deposition of copper carbonate in the southern end of the Briggs mine of the Calumet and Arizona Mining Co. near Bisbce, Ariz., is of great interest. The developed orebodies in the Calumet and Arizona mines are roughly confined to two broad parallel zones separated at the north by a wedge of Copper Queen ground and at the south by an undeveloped block of Calumet and Arizona ground about 2000 ft. (610 m.) wide. The more westerly zone includes the Irish Mag, Oliver, P. and D., and Cole mines, none of which has been operated since 1919. Much of the water from this division is carried from the 1400-ft., or bottom, level at the southern end of the Cole mine in a long water drift through the undeveloped block to the 1300-ft. level of the Briggs mine at the southern end of the more easterly zone. Most of this water comes originally from outlying areas in the P. and D. mine, passing through parts of the lower. levels of the Cole mine, which are heavily mineralized with iron and copper sulfides. This sulfide zone has been opened up and slowly oxidizing for years. Originally a pure, potable water, the analyses of which are shown under A- in Tables 1 and 2, on its way through the mineralized area in the Cole mine it gathers copper, calcium, magnesium, iron, and aluminum sulfates, a load of dissolved mineral salts almost four times as great as that which it formerly carried; analyses B

Jan 1, 1923

By P. E. McKinney

DEVELOPMENTS in engineering during the past decade, particularly as applied to marine construction, mining machinery and other purposes in which corrosion offers a serious problem, have created a large demand for a non-ferrous metal highly resistant to corrosion and at the same time useful in general construction work as a substitute for steel without materially decreasing the factor of safety or increasing the weight of the various parts over that ordinarily used in the case of mild steel. To obtain the combination of desired properties many compositions have been proposed and used with excellent success, but at the present time probably the most popular and most widely used combination is the non-ferrous alloy commonly called manganese bronze. This is nothing more than a high brass to which have been added, by the proper method of alloying, comparatively small percentages of aluminum, iron, or manganese with the definite purpose in view of strengthening the alloy and rendering it more dense and close-grained than the average yellow-brass casting. In the manufacture of manganese bronze a great deal has been said about the importance of using only the highest grades of raw material and the beneficial or detrimental effects, as the case may be, of various impurities, as well as the importance of adding the ingredients according to various formulas proposed; but in most of these cases the literature on the subject has dealt principally with the manufacture of this alloy from virgin metals And raw materials of the highest purity. It is the purpose of this paper to deal particularly with the possibilities that lie in the proper development of methods for manufacturing such an alloy by more economical methods than those which have usually been discussed in other literature on the subject. Shortages have recently existed in raw materials needed for many products entering into the various branches of engineering work, particularly the non-ferrous metals, and during the next few years of reconstruction the country will be flooded with many

Jan 2, 1919

By Donald R. Williamson

Ore estimation at Cyprus Pima mine begins with estimating average copper grades for mine model blocks. Accuracy of the estimates has been checked four times in the last several years by comparing the estimates with arithmetic averages of corresponding blasthole (BH) assays. The data file now contains 3.567 estimated blockgrades and more than 10,000 blasthole assays. These data were compared by straight-line regression analysis at appropriate intervals as the body of data grew. Arithmetic averages of the estimates differed each time from arithmetic averages of the BH averages by nearly the same amount. More significantly, regression curves of the new total sets of data did not change position appreciably showing that copper grade estimates of blocks in all grade ranges from the lowest to the highest grade ores remained in error by nearly the same amount. Other studies revealed that core hole assays of the dominant ore type are biased and that that bias almost equals the error in estimation. Discovery of constancy in error indicated that regression analysis could be a means for correcting estimates of average block copper grades. A correction for estimated block grades was developed. It required determining which regression is appropriate for the particular problem, and a mechanism that is demonstrably sound. This paper describes the problem and the solution: No comparable study has been, found in the literature. Two other applications of regression analysis to metal grade comparisons are presented. Each adds a bit of support to a generalization which was suggested by correction of average block copper grades, namely, when performance of an estimate is to be evaluated, the variable taken to be the yardstick for the performance should be regressed on the estimate.

Jan 1, 1980

By John Park

THE mining .district is located in the northeasterly part of Nevada, between the Jarbidge River on the west and the East Fork of the Jarbidge on the east. The northern boundary of the district is but a few miles south of the Idaho state line-the gold-bearing area extending from this point south, for 5 or 6 miles. The Jarbidge Mountains, in which the ore deposits occur, range from 5000 to 11,000 ft. in elevation, the most important mines being situated about 7000 ft. or higher. The town of Jarbidge lies along the Jarbidge River and is reached by stage from Rogerson, Ida., the nearest railroad point. During the summer months, the camp may be entered from the south by way of Deeth, Nev., but no regular transportation facilities are available over this route. HISTORY The mineral deposits were not discovered until 1909, when D. A. Bourne, panning along the river bank, found gold in the gravel at the mouth of a small stream flowing into the Jarbidge. He prospected in the vicinity of this stream, later known as Bourne Gulch, and shortly after located the North Star claims. During the following spring and summer (1910), the camp of Jarbidge grew from nothing to a town of 2000 people and the hills surrounding it were practically all taken up by mining claims. Most of the work done during. the first year or two consisted of trenching and open-cut prospecting. Tunneling was started on a number of claims and many veins were uncovered. Mills were built and operated on a few properties, notably the Pavlak and the North Star. These ran only a few months, however, when they were closed down because of extraction and financial difficulties.

Jan 1, 1925

By Charles Catlett

Some years ago the writer was struck by what might be called the remarkable vitality of the Virginia furnaces during the panic of 1893; and attention was called to the fact in the American Manufacturer of February 8,1895. From the second half of 1892, which was a period of maximum output, to the second half of 1893, when the full effects of the depression had been reached, the output of pig-iron had fallen off in Illinois 85; in New York, 66; in Ohio, 51; in Tennessee, 44; in Pennsylvania, 28; and in Virginia only 15 per cent. It seemed a reasonable inference that the State which had thus shown its marked ability to meet hard times could make and market its product with a larger margin of profit than any of the other States. This was true at that time, and to a certain extent the reasoning still holds good; but my mistake was in not fully realizing the marked effect of the Mesabi development, combined with reduced economies in transportation, and the consequent advantage to those furnaces which were so situated as to utilize these new commercial factors. The effect of these factors is seen in comparing the second half of 1894 with the second half of 1892. New York had dropped off 44, Alabama 23, Tennessee 21, Illinois 19, and Virginia 16 per cent., while Pennsylvania had increased 5 and Ohio 10 per cent. While there is no question of the great economy which has been made possible for certain interests which are peculiarly situated with reference to the ores of the Northwest, it is yet too early to say what furnaces not so fortunate will have to pay for their raw material. Already an increase of twenty cents per ton of ore has been announced, based upon increased cost of production.

Jan 1, 1900