Search Documents

AN excerpt from the Odessa Isvestia Vechernia, dated April 24, 1927, and translated by P. Routzitzky, summarizes a report by Professor Preobragensky ad-dressed to the Russian Government. Professor Preo-bragensky writes in regard to newly discovered potash deposits in eastern European Russia. Near Solikamsk in the Perm district, about 100 miles east of the Ural mountains and on the Kama river, large deposits have been located and the belt has been traced southward about 25 miles. Subsequently the search for potash salts has been transferred to the Berezovsky district, near Nikolsk, on the Kosva river, about 70 miles north-east-of the city of Perm. Toward the end of March, 1927, at a depth of 800 ft., drilling at the Levensk salt works revealed potash salts in, definite strata. The bed has a thickness which extends from a depth of- 245 to 307 meters (latest data in middle of April, 1927) and has not been bottomed yet. Professor Preobragensky goes on to say that these operations have definitely, developed very large de-posits, the limits of which are still unknown. There is at least an implication that the reserves far exceed those of Stassfurt, Germany. For European use they are, of course, much less accessible, for by through rail they lie 1200 miles east of Petrograd. Further, no particulars are given as to the potash content. It is to be supposed that the salt occurs in the Permian beds that extend north and south along the west flank of the Ural mountains, as the localities mentioned .all lie within the area so mapped on the new geologic map of Russia issued by the Scientific and Technical Di-vision of the All-Russian Council of Soviets in 1922. It is interesting to note that these salt beds are of the same geologic age as those of 'the Stassfurt region and of the west Texas-New Mexico district, in which the U. S. Bureau of Mines is at present drilling.

Jan 7, 1927

By C. F. Quest, T. S. Washburn

The steel industry has a definite need in its tonnage mills for a formula relating expected tensile strength to the analysis of the steel. The McWilliam-Barnes1 and other less comprehensive formulas are used for this purpose, but these formulas were designed for an analysis range that does not include the medium manganese and silicon-bearing steels. This type of steel is being produced to meet the demand for tensile strength slightly higher than that of ordinary structural steel but not high enough to justify expensive alloy steels. The purpose of this paper is to present a somewhat more comprehensive formula based on data accumulated over a number of years by the Inland Steel Co., and to discuss the method followed in obtaining a formula to fit the data. The resultant formula admittedly is still weak in some respects, but for the expanded analysis range appears to be an improvement over the other formulas. It is hoped that with the collection of more data and possible collaboration with other mills studying this problem it will be possible to work out a more nearly perfect formula. Several publications have been issued on this subject. In some, the equation type of relation was evolved while others made a combination of tables and an equation. The latter include work by Campbel12,3 and Webster.4,5 Campbell classified the steels as acid and basic and applied a different formula to each. For basic steels, he used the equation: Teosile etrength = 41500 + 770C + 1000P + yMn [1 y was a variable depending on the carbon and manganese content of the steel and was listed in tables. Webster investigated acid Bessemer steel and developed the equation: Tensile strength = 38000 + 800C + xTP+ yMn [2]

Jan 1, 1940

By C. F. Quest, T. S. Washburn

The steel industry has a definite need in its tonnage mills for a formula relating expected tensile strength to the analysis of the steel. The McWilliam-Barnes1 and other less comprehensive formulas are used for this purpose, but these formulas were designed for an analysis range that does not include the medium manganese and silicon-bearing steels. This type of steel is being produced to meet the demand for tensile strength slightly higher than that of ordinary structural steel but not high enough to justify expensive alloy steels. The purpose of this paper is to present a somewhat more comprehensive formula based on data accumulated over a number of years by the Inland Steel Co., and to discuss the method followed in obtaining a formula to fit the data. The resultant formula admittedly is still weak in some respects, but for the expanded analysis range appears to be an improvement over the other formulas. It is hoped that with the collection of more data and possible collaboration with other mills studying this problem it will be possible to work out a more nearly perfect formula. Several publications have been issued on this subject. In some, the equation type of relation was evolved while others made a combination of tables and an equation. The latter include work by Campbel12,3 and Webster.4,5 Campbell classified the steels as acid and basic and applied a different formula to each. For basic steels, he used the equation: Teosile etrength = 41500 + 770C + 1000P + yMn [1 y was a variable depending on the carbon and manganese content of the steel and was listed in tables. Webster investigated acid Bessemer steel and developed the equation: Tensile strength = 38000 + 800C + xTP+ yMn [2]

Jan 1, 1940

By M. E. Wadsworth, D. R. Wadia

The rate of reaction of cuprite was measured in a series of sulphuric acid solutions, from which oxygen had been excluded, at various concentrations and temperatures. The overall reaction CuzO + H2S04 + Cu " + CuO + H20 + So4' may be explained quantitatively by two simultaneous rate reactions involving not only H+ but also the hydrolytic adsorption of H2SO4. The results indicate the importance of considering surface mass balance relationships associated with heterogeneous surface reactions. T EACHING has long been an important method for the recovery of metals from certain minerals. Many processes have assumed minor importance in modern practice but such operations as the recovery of uranium and present interest in high pressure-high temperature solution of sulphides' ' well illustrate the importance of leaching as a unit operation. Little quantitative information is available in a form sufficient to determine the mechanism of solution at the solid-aqueous solution interface for given systems. For this reason, it is important that fundamental studies of leaching processes be conducted so that parameters associated with such surface reactions may be understood and correlated. Cuprite was chosen for this study as a result of a recent investigation carried out at the University of Utah on ores of the Ray and Chino Mines Divs. of the Kennecott Copper Corp. These sulphide deposits contain sufficient oxidized minerals, such as cuprite, malachite, and azurite, so that recovery of metal values contained in the oxidized fraction is of primary interest. Of these oxides, cuprite (Cu,O) is the most interesting, since it dissolves in sulphuric acid by an oxidation reduction couple resulting in the formation of 50 pct metallic Cu and 50 pct cup-

Jan 1, 1956

By Paul D. Merica, W. A. Mudge

ONE of the most prominent features of our present-day industrial development is the ever-increasing demand put upon materials of construction Engineering ingenuity, within the past 25 years, has been unusually active, and in some fields at least engineers frankly say that engineering design has progressed as far as the limitations imposed by the properties of the present materials of construction will permit. Consequently, they are today demanding improvement in their working materials and seeking new ones, through the aid of which the present limitations of design may be overcome The activity of this search is evident in all fields, but it is particularly so in that of structural materials required to be resistant to corrosion The corrosion resistance of metals and alloys is never absolute and all-inclusive, a particular alloy will withstand some corrosive conditions well and fall utterly under others Furthermore, other properties, physical and mechanical, required in conjunction with corrosion resistance vary considerably for different commercial applications One wants a soft, ductile sheet metal resistant to atmospheric corrosion, another, a high-strength alloy resistant to sulfuric acid The last decade has witnessed active and definite progress in the development of high-strength, corrosion-resisting alloys In June, 1924, a symposium by the American Society for Testing Materials, on Corrosion-Resistant, Heat-resistant and Electrical-resistance Alloys, disclosed no less. than 60 commercial alloys the properties of which were described as being suitable for industrial service where corrosion resistance

Jan 1, 1935

By John R. Lotz

A team of American experts is tackling a whole nations's problems, under the banner of a seven-year plan evolved by the Iranians themselves.

Jan 7, 1950

By J. L. Gregg

A study of copper-base and silver-base alloys was made with the object of finding, if possible, useful alloys subject to dispersion hardening. These studies led to the discovery of several alloys showing considerable dispersion hardening, the most important of which, the alloys of copper with iron, nickel, cobalt and chromium silicides, have since been very ably reported by M. G. Corson.l This paper is offered as a few notes covering alloys other than those described by Corson and some further data on the silicide alloys. Copper Alloys For the purpose of making a rapid survey of copper alloys that might show useful dispersion-hardening phenomena, various alloys were prepared containing 3 per cent. of additional elements added in such proportion that possible compounds could be formed without an excess of either added element. These alloys in the form of rolled or forged pieces were quenched in water from a temperature of 871" C. (1800" F.) and subsequently aged at various lower temperatures for l-hr. periods. The comparison of the Rockwell hardness of the quenched alloys with the maximum hardness of the alloys after aging was used as a measure of the dispersion hardening. Table 1 shows the Rockwell "E" hardness 1/8-in. ball, 100-kg. load) of the quenched alloys, together with the maximum hardness resulting from aging. The reheating temperature given in this table is the aging temperature at which maximum hardness resulted from a l-hr. sojourn. From this table it may be observed that only the silicide alloys showed significant dispersion hardening. Of these, the only one not described by Corson is the Cu-Be-Si alloy. This alloy contained 1.35 per cent. beryllium and 1.78 per cent. silicon, which is approximately equivalent to 3 per cent. Be2Si. It had a yellow color and scaled much less than the other silicide alloys upon heating. It could be worked easily either hot or cold but hardened very rapidly on cold working. The annealed alloy upon drawing from a diameter

Jan 1, 1929

By Courtenay DeKalb

The accompanying illustrations, Figs. 1 to 6, from plans drawn by Mr. T. L. Knapp, a student in the Missouri School of Mines, show a type of furnace designed by the writer, which possesses some peculiarities intended to meet the necessities of laboratory-instruction in that institution. The object aimed at was the construction of a simple, inexpensive furnace, suitable for the distillation of zinc from its ores, and using only a single retort. This limitation imposed the chief difficulty, owing to the necessity of obtaining a high degree of heat concentra ted upon the retort. This is accomplished by the peculiar curve of the arch, which consists of arcs of seven distinct ellipses, one focus of each of which lies within the area occupied by the retort. Thus the reflected heat would necessarily be thrown mainly where most needed, namely, on the retort. Conservation of heat is provided for by a return-flue through the hollow arch, and by a sand bottom under the fire-brick hearth. Four openings lead back from the laboratory, or heating-chamber in this instance, to the arch-flue; and three openings lead from the arch-flue to a large horizontal flue, from which a down-take conducts the gases to the stack. The fire box, it dl be observed, is deep, thus producing much CO during the combustion of the coal. The further combustion of this CO may be accomplished by the admission of air through the hollow fire-bridge, thus producing a higher flametemperature surrounding the retort. Provision is also made for removing the retort and the portion of the wall supporting it and the condenser, leaving a high arch, into which a door-frame may be inserted; the space above being temporarily bricked in. By this alteration, which may be quickly and easily made, the furnace may be converted into a reverberatory, suitable for treating small charges such as

Jan 1, 1898

By J. L. Gregg

A study of copper-base and silver-base alloys was made with the object of finding, if possible, useful alloys subject to dispersion hardening. These studies led to the discovery of several alloys showing considerable dispersion hardening, the most important of which, the alloys of copper with iron, nickel, cobalt and chromium silicides, have since been very ably reported by M. G. Corson.l This paper is offered as a few notes covering alloys other than those described by Corson and some further data on the silicide alloys. Copper Alloys For the purpose of making a rapid survey of copper alloys that might show useful dispersion-hardening phenomena, various alloys were prepared containing 3 per cent. of additional elements added in such proportion that possible compounds could be formed without an excess of either added element. These alloys in the form of rolled or forged pieces were quenched in water from a temperature of 871" C. (1800" F.) and subsequently aged at various lower temperatures for l-hr. periods. The comparison of the Rockwell hardness of the quenched alloys with the maximum hardness of the alloys after aging was used as a measure of the dispersion hardening. Table 1 shows the Rockwell "E" hardness 1/8-in. ball, 100-kg. load) of the quenched alloys, together with the maximum hardness resulting from aging. The reheating temperature given in this table is the aging temperature at which maximum hardness resulted from a l-hr. sojourn. From this table it may be observed that only the silicide alloys showed significant dispersion hardening. Of these, the only one not described by Corson is the Cu-Be-Si alloy. This alloy contained 1.35 per cent. beryllium and 1.78 per cent. silicon, which is approximately equivalent to 3 per cent. Be2Si. It had a yellow color and scaled much less than the other silicide alloys upon heating. It could be worked easily either hot or cold but hardened very rapidly on cold working. The annealed alloy upon drawing from a diameter

Jan 1, 1929

"Located on the Big Hole River, three miles from Divide, Montana, and 21.75 miles from Butte.Built in 1899.DAM: Rock-filled wooden crib, 512 ft. long and 57.5 feet high.SPILLWAY: Equipped with flash-boards 189 ft. long, 8 ft. 10 inches high.PENSTOCKS: Two 8 ft. diameter of steel, each branching and supplying two wheels.WHEELS: Four double horizontal, double discharge turbines, made by The James Leffel & Co., 1,000 h-p., 180 r. p. m., direct connected to generators, operating at 60 ft. head. GENERATORS: Four G. E., revolving field, 750 k-w., 180 r. p. m., 800 volt, 3 phase, 60 cycle alternators.EXCITERS: Two water-wheel driven exciters.TRANSFORMERS: 12 250-k-w. G. E. air blast, primary 15,000 volts, Secondary 800 volts.OPERATION: The plant operates essentially as a peak load plant. Except in flood period, there is insufficient water to operate at full load continually. In December its average output is about 500 k-w."

Jan 1, 1913

By H. Landsberg

MANY of the sedimentary rocks contain small amounts of radioactive constituents. These vary in quantity in different layers. Some recent deposits show rather high activity as; for example, the deep sea oozes and some lake deposits.1,2. Measurements made in boreholes have also shown considerable changes in activity from horizon to horizon. The first to publish data on this fact was Ambronn,3 and recently Russian geophysicists have shown remarkable variations of activity from one layer to the next in various wells. Spak4 felt even that he was able to line up horizons from data measured in two neighboring wells. ? The measuring of radioactive radiation is fairly difficult. Large errors are possible by the circulation of gaseous emanations in the well and porous strata. It is, therefore, never certain whether the activity of the layer where the instrumental device or collector is located will be measured, or that of some adjacent layer, For this reason it seemed to be advantageous to take samples of rocks into the laboratory and test them therefor their contents of radioactive material, Such a method has been followed in the past to distinguish radioactive ore from other rocks. Radioactivity of rocks, especially of the igneous type, was also deter-mined in the laboratory by numerous authors for absolute age investi-gations.6 Corresponding data from studies of sedimentary formations are scarce. Specimens taken from a core of the Bradford oil sandstone were tested by Landsberg and Ingham,7 with the results illustrated in Fig. 1, which shows that within relatively small vertical distances the differences of relative activity were considerable. If one assumes that the distribution of radioactive material is fairly uniform throughout a layer, measurements of radioactive radiation in various horizons would offer additional information for stratigraphic

Jan 1, 1939

By W. J. Whiten

Current developments in one type of crushing and screening model is reviewed and general design techniques and policies are proposed for the control of crushing plants.

Jan 1, 1984

By B. M. Harra, R. L. Hallows, O&apos

The term "modern automatic baghouses" as used in the title of this paper is intended to designate a general type of mechanical fume filter, introduced some 20 years ago and gradually improved since that time. It is characterized by its small filtering bags, enclosed in groups of 15 to 30 in steel compartments, and by its frequency of shaking, as compared to the old type of baghouse, which uses much larger bags, shaken at much longer intervals. Automatic baghouses are produced by a number of well-known manufacturers. Some recently constructed baghouses of the old type have embodied some of the principles of the automatic type, in that they are divided into several compartments, with separate fans for the different compartments, and flue headers arranged so that when the fan to any one compartment is shut down preparatory to shaking the bags in that compartment, the bags are put under suction by the draft from the other fans, thus making possible more efficient cleaning of the bags. These baghouses have motor-driven shaking mechanisms, and generally are operated under higher pressure and shaken at more frequent intervals than was the practice with the old style baghouse, and consequently have greater filtering capacity per unit of bag area. It is possible to interconnect the fan motors and the motors driving the bag-shaking mechanism, with suitable relays and timing devices, so that the operation of this type of baghouse also becomes to a considerable extent automatic. These baghouses are intermediate between the old style of baghouses, strictly speaking, and the completely automatic baghouses. They may he considered just as modern as the latter, and their proponents can no doubt cite many advantages for them. The authors are less familiar with them than with other types, and the following discussion will be limited to a comparison of the automatic baghouses and old style baghouses, with particular reference to the experience of The Eagle-Picher Lead Co. and The Eagle-Picher Mining and Smelting Company.

Jan 1, 1937

By W. B. Plank

Those interested in training engineers for the mineral industry should consider how their men may fit into the general industrial recovery that now seems well started. One hears occasionally that too many engineers have been produced, especially mining engineers, and that the opportunities for their employment are decreasing. Just what is the situation? Enrollment in American engineering schools has fallen off sharply during the past few years. In 1930-31, the year of peak enrollment in all engineering schools, there were 78,685 engineering students in the United States, but in 1932-33 only 67,584, a decrease of 14 per cent. President Walters, of the University of Cincinnati, in his survey of 74 engineering schools, published in School and Society of Dec. 16, 1933, estimates that the engineering enrollment for 1933-34 is 10 per cent under that of 1932-33, or about 60,000. The situation in the mineral .ethnology schools somewhat parallels this general trend, although not to the same degree. Last year there were 4443 students in mineral technology schools, compared with 4687 in 1930-31, a decrease of 5 per cent. This year, with 3995 students, the enrollment shows a decrease of 10 per cent from last year, or a decrease of 15 per cent from 1930-31. Enrollment has no doubt been influenced by the condition of the mincral industry, just as the enrollment of other engineers has been affected by general industrial conditions. But the mineral industry, which is the first to recover, has not been so seriously affected as have some of the manufacturing industries during the past four years. This is especially true of coal and gold mining, which have been increasing rapidly in their production during the past year and have given employment to more men. Ten years ago, approximately 1,000,000 men were employed in the coal and metal mines and quarries, compared with probably half that number now. The number of mining engineering graduates in 1934 will be 234 and in metallurgy 252. In other words, fewer than 500 graduates are entering these industries the present year. With conditions improving in the mineral industry, coupled with a falling enrollment in our mining schools, there certainly exists an opportunity for young men now beginning their training for this industry.

Jan 1, 1934

By John A. Von Essen

To some, the paddle mixer may seem old as antiquity. Yet, as industrial mixing requirements become increasingly sophisticated in the late 20th century, it is proving more useful and versatile than ever. From water treatment applications to high-pressure reactors, the new and specialized demands in mixing have been met by a continuous evolution and adaptation of this basic workhorse design.

Jan 7, 1978

By E. Dow Whitney, Ravrinda M. Chhatre, George Y. Onoda

Phosphate deposits in Florida are a possible source of byproduct uranium. In this paper, the distribution of uranium in several recently mined areas is described. Flowsheets are established for several mines describing how the uranium becomes distributed during the beneficiation of the phosphate matrix.

Jan 1, 1981

By J. J. Bodmer

THE four different modes, more or less practiced for subdividing slag (that is, producing slag sand), are the following : 1. Crushing the slag from the lump in Blake's crusher, by edge runners or other suitable means. 2. Blowing water, steam, cold or hot air, into the stream of viscous slag whilst it runs from the furnace. So treated, the slag takes

Jan 1, 1874

By K. A. Lambert

In the Anthracite Region there are considerable areas where the original mining was done 50 or more years ago. In this original mining, the pillars that were left proved inadequate in size for the support of the roof, which has since collapsed as a result of squeezes, and completely filled the original openings. In an endeavor to recover the coal which remains in the pillars in such areas, the reopening cost for development, as well as for pillar recovery, has been excessive in many instances. Various methods have been tried out with a view to lowering the cost, in order that the greatest possible percentage of recovery of the reserve tonnage may be realized economically. Ordinary hand mining necessitates the driving of development road 10 ft. wide in the clear between timber legs, with 6 ft. of clearance over the rail to accommodate mine cars; collars or crossbars on the timber sets have been difficult to maintain in these openings in the heavily caved condition, especially in beds where the overburden is great,. Numerous failures have occurred on these development road timbers because of roof movement resulting from removal of pillars. The actual removal of pillars from this development work has been costly because full-width openings for transporting mine cars to the face have to be maintained by cleaning caved material from alongside the pillars, or skipping up along the pillars where pillars of sufficient width are found. Shaker-chute Methods A method of developing such caved conditions and recovering pillars tributary to this development, utilizing shaker chutes, is being tried out with considerable success at Loree colliery. An outline of the chute and apparatus is shown in Fig. 1, which indicates the location of pillars and caved material. The cost of both labor and material required in the recovery of such coal is considerably less than by ordinary hand methods. In order to try out this method of mining a location was chosen where a tightly caved area had been developed by ordinary hand methods to within 300 ft. of the property line. The original bed height was 12 ft., with an overburden of 325 ft., but on account of the squeezes which

Jan 1, 1931

By N. W. Ratliff, P. J. Closmann

Production of oil by expansion from a cylindrical reservoir composed of two concentric regions of different properties has been determined as a function of time for a reservoir producing at constant terminal pressure. The parameters involved are permeability, porosity, compressibility and oil viscosity. Results agree with those of a generally accepted method for uniform reservoirs when all parameters are taken as uniform. Cumulative production at any given time is reduced below that of the uniform reservoir when a region of considerably lower permeability adjoins the well; cumulative production increases when a high-permeability region adjoins the well. Curves are presented illustrating quantitative effects of these variations. INTRODUCTION Most petroleum reservoirs can be exploited by release of pressure and consequent expansion of underground fluid. During part of the production history of certain reservoirs by this mechanism, fluid compressibility can be considered small and constant. Cumulative fluid produced by this means as a function of time was calculated for a uniform reservoir by van Everdingen and Hurst.l For certain cases where a production well has been damaged or where an acid treatment has been used, a zone of properties different from those of the reservoir may be created around the production well. In such a case, expansion of the reservoir fluid takes place in a system composed of two concentric cylindrica1 regions of different reservoir properties. Such composite systems were studied in connection with heat flow by Jaeger2 who presented a solution for temperature distribution in a radial system with an infinitely large outer radius. Similar heat flow problems have been studied by other authors Oil production from composite reservoirs was studied for constant production rate by Hurst,4 Loucks and Guerrero,5 and Carter.6 THEORY This work considers constant terminal pressure. Cumulative flow is calculated for a composite bounded system in which no flow takes place across the outer boundary (Fig. 1). Since the flow is considered to be purely radial, the problem involves only one space dimension and time. It is convenient to define the following dimen-sionless pressure drops (Fig. 1).

IF you wish to make the acid that is vulgarly called common aqua fortis,* for parting gold from silver, you must first provide as many cucurbits and alembics, receivers, and materials as you wish, and then make a furnace that is long and conveniently wide for holding three or four pairs of cucurbits or as many as you wish. If you have to make this by art in order to work a large quantity, you could make several small furnaces for it seems that not more than three or four pairs are suitable for one. Prepare the places where the cucurbits are to stand with bottoms or covers made of potter's clay or tiles that are half round like the bottoms of the cucurbits and have a little rim around the top so that they can be built in. Proceed to build these in in pairs, one by the other with convenient spaces between, placing an iron support across to make this place stronger and more secure. In every corner and also in the middle a hole must be made as a vent for the smoke, as is done in all furnaces. You will see the form of this somewhat roughly drawn here. [Figure 25] Near this prepare a number of cucurbits which are made of glass, as clear and uniform as possible and very well formed. There must be no bubbles or other indentations in these, for they would be dangerous and uncertain for your work. Lute these with lutum sapientiae up to within three dita or less from where the neck narrows. This lute must be spread out well all over to the thickness of two threads or a little more. Then cover and make them strong with this well-made plaster, and finally dry it, taking care that there are no clefts or cracks such as clays are often prone to make even though they be well prepared. For greater security choose among these [64v] a clay that is lean and then mix it with at least a fourth part or more of wool-clloth clippings and about an eighth part of wash

Jan 1, 1942