Search Documents

By Heinz W. Duddeck, Hans-Konstantin Nipp

The design of storage space or deep mining in rock salt should take into account not only time dependency of the rock salt behavior but also temperature effects. For deep mining of potassium salt the natural increase of temperature with depth may no longer be negligible. For the storage of cryogenic liquid gas in salt caverns more knowledge is nezded about the propagation of deep temperatures and their effects on the stress-strain-creep behavior of the surrounding salt. High temperature problems arise for nuclear waste storages in caverns or drill holes emitting radiation. A numerical model is proposed for the analysis of displacements and stresses including their time and temperature induced change. For the material behavior of salt constitutive equations are chosen composed of a combination of Hooke-Kelvin-Bingham-Newton-model based on experimental results (excluding at present deep cooling), Langer 1980. The parameters involved are depending on the stress level and the temperature. The finite-element-method is applied to rotationally symmetrical three-dimensional problems. The non-linear calculation method is based on an implicit method with respect to time. A modified Newton-Raphson-method and the initial strain approach are employed. Along with some experiences on suitable numerical procedures, examples are shown for the characteristical effects of time-temperature dependency. Having achieved convergency and reliability a method is now available for practical design and parametric sensibility studies.

Jan 1, 1982

By J. W. Miller

One of the major problems confronting coal producers in this highly competitive era is whether or not the potential profit to be made from the products of coal flotation would warrant the capital investment required for the necessary equipment. The author supplies two theoretical cases to illustrate methods for computing such costs.

Jan 3, 1961

By Alec M. Crowell, Harry P. McClintock

Production of oil and gas condensate from the 45 oil and gas fields of South Arkansas increased for the eighth consecutive year, the production for 1943 being 27,605,647 bbl. Six new pools were discovered during 1943, bringing the state's crude oil and condensate reserve to 475 million barrels, a net increase of 70 million barrels for the year. The gross increase in proven reserve was 98 million barrels, from which, of course, is subtracted production of approximately 28 million barrels to reach the net figure of 70 million barrels. There were 35 more wildcats in 1943 than in 1942, and 29 more wells were drilled in fields of the state. Sixteen companies operated exploratory crews during the year for a total of 677 crew weeks, divided as follows: 563 weeks seismograph, 111 weeks gravity and 3 weeks core drill. There was a decided increase in gravity work and a decrease in seismic work. The year started with 15 seismic crews and ended with 5 seismograph and z gravimeter crews. Geologically, it is interesting that the number of wells bottomed in Gulf, Comanche, and Jurassic strata were near equal for the year 1943. During 1942 Jurassic was much higher than the other two. However, Jurassic still led in wildcats for the year 1943. Abandoment of wells in the stripper areas of the state reached about the same figure for the year 1943 as for the year 1942; that is, 145 wells were permanently abandoned. However, 243 wells were drilled in 1943, as against 184 for the previous year. The completions for the year were divided into 103 dry holes, 137 oil and condensate wells and 3 dry gas wells. Among new developments perhaps the most significant was the pressure-main-tenance project for the Midway field of Lafayette County, which is utilizing fresh water as the maintenance medium. This is the first fresh-water pressure-maintenance operation during primary production of an oil field in the United States. The operator of the project, Barnsdall Oil Co., estimates that the ultimate recovery of oil from this field will be increased from 32.5 to 65 million barrels. The Midway pool is of the dissolved-gas type, but a similar project is getting underway for the Magnolia field, Columbia County, a pool of the gas-cap and water-drive type. Dual completion of wells, on concurrent production from two productive zones through a single well bore, became common practice in South Arkansas during the year. As the year ended, some 50 wells had been dually completed and it was estimated that the first 37 of these wells represented a saving of more than 2 1/4 million dollars and a saving in steel of 7000 tons. The majority of the wells dually completed were those reaching depths in the neighborhood of 9000 ft. below the surface and initially productive there. Selective completion at lesser depths in the same well bore proved mechanically feasible and economically sound. The year was marked by the successful completion and placing into operation of three large natural-gas desulphurization

Jan 1, 1944

By Harry P. McClintock, Alec M. Crowell

Production of oil and gas condensate from the 45 oil and gas fields of South Arkansas increased for the eighth consecutive year, the production for 1943 being 27,605,647 bbl. Six new pools were discovered during 1943, bringing the state's crude oil and condensate reserve to 475 million barrels, a net increase of 70 million barrels for the year. The gross increase in proven reserve was 98 million barrels, from which, of course, is subtracted production of approximately 28 million barrels to reach the net figure of 70 million barrels. There were 35 more wildcats in 1943 than in 1942, and 29 more wells were drilled in fields of the state. Sixteen companies operated exploratory crews during the year for a total of 677 crew weeks, divided as follows: 563 weeks seismograph, 111 weeks gravity and 3 weeks core drill. There was a decided increase in gravity work and a decrease in seismic work. The year started with 15 seismic crews and ended with 5 seismograph and z gravimeter crews. Geologically, it is interesting that the number of wells bottomed in Gulf, Comanche, and Jurassic strata were near equal for the year 1943. During 1942 Jurassic was much higher than the other two. However, Jurassic still led in wildcats for the year 1943. Abandoment of wells in the stripper areas of the state reached about the same figure for the year 1943 as for the year 1942; that is, 145 wells were permanently abandoned. However, 243 wells were drilled in 1943, as against 184 for the previous year. The completions for the year were divided into 103 dry holes, 137 oil and condensate wells and 3 dry gas wells. Among new developments perhaps the most significant was the pressure-main-tenance project for the Midway field of Lafayette County, which is utilizing fresh water as the maintenance medium. This is the first fresh-water pressure-maintenance operation during primary production of an oil field in the United States. The operator of the project, Barnsdall Oil Co., estimates that the ultimate recovery of oil from this field will be increased from 32.5 to 65 million barrels. The Midway pool is of the dissolved-gas type, but a similar project is getting underway for the Magnolia field, Columbia County, a pool of the gas-cap and water-drive type. Dual completion of wells, on concurrent production from two productive zones through a single well bore, became common practice in South Arkansas during the year. As the year ended, some 50 wells had been dually completed and it was estimated that the first 37 of these wells represented a saving of more than 2 1/4 million dollars and a saving in steel of 7000 tons. The majority of the wells dually completed were those reaching depths in the neighborhood of 9000 ft. below the surface and initially productive there. Selective completion at lesser depths in the same well bore proved mechanically feasible and economically sound. The year was marked by the successful completion and placing into operation of three large natural-gas desulphurization

Jan 1, 1944

By R. Fahn

Bentonites are best suited for the preparation of acid activated clays with efficient adsorption properties. They are weathering products of acid volcanic ashes and natural deposits are spread worldwide. The main constituent of bentonite is aluminum hydrosilicate montmorillonite with a high ability to swell. Physical and Chemical Properties of Montmorillonite The clay mineral montmorillonite is named after its place of discovery, near Montmorillon in southern France. The structure of this clay is shown in [Fig. 1]. The montmorillonite crystal consists of about 15-20 silicate plates. Each silicate plate is composed of three layers. The central one is formed by aluminum or by ferric hydrate octahedrons, the two outer ones consist of silicon dioxide tetrahedrons. In the presence of water, the montmorillonite crystal swells and water molecules become deposited between individual silicate layers. Two types of natural bentonites are known: the Western type, which is a natural sodium bentonite (high swelling grade), and the Southern type, an alkaline earth or calcium bentonite (low swelling grade). Southern bentonites have efficient adsorption properties of their own. They are called natural active earths or fullers earths. Acid Treatment of Bentonite Under the influence of a mineral acid, the exchangeable alkaline earth ions of bentonite are substituted by hydrogen ions. Moreover, depending on the acid concentration, temperature, pressure, and reaction time, a more or less pronounced leaching process takes place. Thereby Al-, Fe-, and Mg-ions are extracted from the octahedron layers. This results in a change in the crystalline structure of montmorillonite and in an increase of its specific surface area and porosity, as shown in [Fig. 2].

Jan 1, 1983

By Paul W. Chase

Centralized process control has received increasing emphasis in recent years. Its application at U. S. Steel's Minntac facility for production of taconite pellets is discussed in this paper. A brief description of the flowsheet will provide background for discussion of the process instrumentation and digital system.

Jan 1, 1969

By J. A. Dresser

The controlling supply of asbestos for the world is obtained from southern Quebec, 150 miles or less north of the international boundary line between Canada and the United States, and about 75 miles south of the city of Quebec.

Jan 1, 1915

By Thomas Fraser

"AIR-SAND" is the term which has been given to a process of separating refuse material from coal by means of a body of dry sand artificially fluidized and maintained in that condition by a continuous stream of air bubbles flowing through the sand body. By proper regulation of the rate of air flow, this fluid air-sand body may be maintained at such a density that coal will float near the surface and the refuse, which is heavier, will sink through the sand to the bottom of the container. This separation is a float-and-sink operation similar to the separation of wood chips and stones in water; the one floats and the other sinks, irrespective of size of pieces. This was the objective sought in the development of this method of cleaning coal-a dry process which requires no preliminary sizing of the coal. METHOD OF PRODUCING THE AIR-SAND MEDIUM Figure 1 shows the cast-iron cell used for testing at the Central District Experiment Station of the Bureau of Mines, Urbana, Ill. This consisted of two castings: a. rectangular box 12 in. square in cross section and 18 in. tall, open at both ends and flanged on the bottom; and a cubical box also 12 in. square inside, with a closed bottom and flanged top. A porous diaphragm is bolted between the flanged ends of the two castings. The upper part of the cell above the diaphragm is filled with river sand screened through 20 mesh without removing the dust. Air under suitable pressure is admitted to the lower part of the cell below the diaphragm. The air passes through the diaphragm and bubbles up through the sand, distending the mass and throwing the sand particles into motion.

Jan 2, 1926

By John Blatchford, H. O. Hofman

The leading antimony mineral is stibnite. In smelting stibnite ore two processes are available, precipitation and roasting-reduction. The former is suited only for high-grade ores. As low-grade ores are more common than high-grade, roasting-reduction is of greater importance than precipitation. In the roasting process the aim may be to leave the oxidized antimony in the ore, or it may be to volatilize as much of the antimony as possible, collect the volatilized oxide as a rich intermediary product and smelt it for antimony, leaving the gangue poor enough to be considered a waste product. Whichever way the roast is conducted certain difficulties inherent in stibnite are encountered. These are: 1. The low melting point of stibnite which, according to Pélabon,' is 550°C., according to Wagemann2 540°C., and according to Borgstroma 546°C. 2. The ignition temperature: According to Friedrich,4 stibnite, if heated in air, begins to oxidize at 290°C. if the size of a grain is 0.1 mm. in diameter; at 343", if 0.1 to 0.2 mm.; and 430" if 0.2 mm. 3. The fusibility of a mixture of Sb2S33 and Sb203 which in the form of kermesite (Sb2S3)z.Sbz03 melts at 517°C.6 4. The volatility of Sb2Ss and SbzOs, for which no numerical data appear to exist, although practical experience has shown that they are volatile at low temperatures. As regards the oxidation of metallic antimony, we have the experimental evidence of C. F. Plattner6 that when fused and brought to a red heat, it burns with a bluish-white flame to Sb2Oa which passes off as a

Jan 1, 1916

The Institute conducts jointly with the American Society of Civil Engineers, American Society of Mechanical Engineers and American Institute of Electrical Engineers, certain activities as listed below, and is joint owner with them of certain properties. United Engineering Trustees, Inc. When Mr. Carnegie made. his gift ?for the erection of a suitable home? for the engineering societies,

Jan 1, 1942

By Thomas M. Tharp

INTRODUCTION Attempts to analyze the stability of slopes, foundations and underground openings in discontinuously jointed rock have generally assumed full joint continuity or ignored the role of stress concentration at the tips of discontinuous joints. The most common approach in rock slopes is to consider a failure plane consisting of coplanar, but discontinuous joints separated by intact rock. The intact rock is assumed to fail in shear as a Mohr- Coulomb material and to contribute a strength component proportional to the fraction of the failure plane that is intact rock (Jennings, 1970). An alternative approach by Stimpson (1978) applies Lajtai's (1969) theory for shear strength of discontinuously jointed rock masses to slopes. Lajtai allows tensile failure in the intact rock of a composite surface. This theory yields lower shear strength than that of Jennings (1970) except in the presence of high normal compression, however it also fails to account for the stress concentration at the tip of a discontinuous joint. For a given slope geometry, stresses increase with slope height, but in both of these models rock mass strength is independent of size. A fracture mechanics analysis shows that particularly for small slopes, rock mass strength decreases with size. A continuous stepped failure surf ace produced by propagation of preexisting joints may develop at lower shear stress than predicted by the Jennings (1970) or Lajtai (1969) models. This fracture mechanics model applied to slopes in competent rock is more realistic in its assumed failure mechanism, and for large slopes more conservative than the Jennings (1970) or Lajtai models (1969).

Jan 1, 1984

By A. A. Schweizer

A method to improve the quality of Magmont zinc concentrates to become acceptable feed to an electrolytic zinc refinery is described. The magnesia content of zinc concentrates produced was too high due to particle locking with sphalerite in coarse fractions. Regrinding the concentrates to a very fine particle size and then refloating the sphalerite was chosen to eliminate a sufficient amount of the magnesia to make the concentrates acceptable.

Jan 1, 1984

By H. Rush Spedden, Arvid Thunaes

Pilot plant test work in 1942 and 1943 showed that by a combination of desliming, fine-size classification, and Sullivan deck concentration it is possible to recover heavy minerals such as cassiterite at least as fine as 10 microns in size. This appreciable improvement in gravity concentration practice has been substantiated by several full-sized plants.

Jan 8, 1950

By R. G. Ward, John Henderson

It has been shown1 that the observed density1-' of liquid iron silicates in contact with solid iron depends upon whether nitrogen or argon is used to protect the experimental system from oxidation. These densities have been measured by the maximum bubble-pressure method, in five different labora-

Jan 1, 1965

By A. Stumpf, Y. Berube

An experimental apparatus for studying the aqueous oxidation of sulfide minerals is presented. The oxidation kinetics for molybdenite in solutions of caustic soda and dissolved oxygen are discussed; results of leaching experiments on chalcopyrite concentrates are given. Preliminary results on the transfer of oxygen into water are also discussed.

Jan 1, 1974

By William E. Ford, Edward Salisbury Dana

296. Definition of Specific Gravity. - The specific gravity of a mineral is the ratio of its density * to that of water at 4' C. (39'2' F.). This relative density may be learned in any case by comparing the ratio of the weight of a certain volume of the given substance to that of an equal volume of water; hence the specific gravity is often defined as: the weight of the body divided by the weight of an equal volume of water. The statement that the specific gravity of graphite is 2, of corundum 4, of galena 7-5, etc., means that the densities of the minerals named are 2; 4, and 7'5, etc., times that of water; in other words, as familiarly expressed, any volume of them, a cubic inch for example, weighs 2 times, 4 times, 7.5 times, etc., as much rn a like volume, a cubic inch, of water. Strictly speaking, since the density of water varies with its expansion or contraction under change of temperature, the comparison should be made with water at a fixed temperature, namely 4' C. (39'2' F.), at which it has its maxi- mum density. If made at a higher temperature, a suitable correction should be introduced by calculation. Practically, however, since a high degree of accuracy is not often called for, and, indeed, in many cases is impracticable to attain in consequence of the nature of the material at hand, in the ordinary work of obtaining the specific gravity of minerals the temperature at which the observation is made can safely be neglected. Common variations of temperature would seldom affect the value of the specific gravity to the extent of one unit in the third decimal place.

Jan 1, 1922

By William E. Ford, Edward Salisbury Dana

1. THE SCIENCE OF MINERALOGY treats of those inorganic species called minerals, which together in rock masses or in isolated form make up the material of the crust of the earth, and of other bodies in the universe so far as it is possible to study them in the form of meteorites. 2. Definition of a Mineral. - A Mineral is a body produced by the proc¬esses of inorganic nature, having a definite chemical composition and, if formed under favorable conditions, a certain characteristic molecular structure which is exhibited in its crystalline form and other physical properties. This definition calls for some further explanation. First of all, a mineral must be a homogeneous substance, even when minutely examined by the microscope; further, it must have a definite chemical composition, capable of being expressed by a chemical formula. Thus, much basalt appears to be homogeneous to the eye, but when examined under the microscope . in thin sections it is seen to be made up of different substances, each having characters of its own. Again, obsidian, or volcanic glass, though it may be essentially homogeneous, has not a definite composition corresponding to a specific chemical formula, and is hence classed as a rock, not as a mineral species. Further, several substances, as tachylyte, hyalome¬lane, etc., which at one time passed as minerals, have been relegated to petrology, because it has been shown that they are only local forms of basalt, retaining an apparently homogeneous form due to rapid cooling. Again, a mineral has in all cases a definite molecular structure, unless the conditions of formation have been such as to prevent this, which is rarely true. This molecular structure, as will be shown later, manifests itself in the physical characters and especially in the external crystalline form.

Jan 1, 1922

By W. E. Dunn

CHLORINATION of titanium ores and slags is the source of TiCl,4 intermediate between ore and metal. A number of chlorinators are operating in the United States using a wide diversity of ores. These chlorinators vary in design to accommodate the ore source, but all use chlorine and carbon.

Jan 1, 1961

By S. R. Bardsley, S. T. Algermissen

Induction, nuclear and sonic well-logging methods were employed in a Green River formation oil-shale analysis and evaluation study conducted in northeastern Uintah County, Utah. The physical and chemical properties of an oil-shale section, previously cored and assayed by conventional methods, were used to evaluate the response of the various logs. The logging program was designed to measure variable properties of oil shale which relate to oil-yield potential in order that a relationship between assay-oil yield and log-determined properties could be identified, thereby permitting a direct determination of yield potential from logs alone. All of the major oil-shale zones and section ttlarkers are recognizable on the logs used in the study. The relationship between the response of the Density and Sonic logs and the assay-oil yield in gallons per ton was suficient to perinit the derivation of equations expressing the relationships. These equations can be used to determine the potential oil yield in gallons per ton of an oil-shale zone or section. The Neutron log response distinguishes the rich oil-shale intervals from the lean intervals, but does not appear to permit establishment of a quantitative relationship. The Garnma-Ray and Induction logs indicate only a qualitative relationship to oil-shale yields. Logging oil shale by Gamma-Gamrna Density and/ or Sonic logging methods will permit a fast, economical and accurate means of evaluating the potential yield of oil-shale deposits. Considerable sums of money have been allocated to Green River formation oil-shale evaluation during the past years by both private enterprise and Federal and state governments. The result of the work accomplished to date is commendable, but the task of fully exploring and evaluating one of the world's greatest reserves of potential energy for economical exploitation is enormous and much information is still needed. Present methods of evaluation consist primarily of sampling and assaying the oil shale for potential yield. The data received are excellent, but are both costly (inasmuch as it requires funds specifically allocated for the evaluation purpose) and time-consuming (as each representative sample must be assayed in the laboratory by specially trained personnel). At the present time, the Green River formation oil-shale province is one of the most active areas in the Rocky Mountain region for exploratory oil and gas drilling. This activity could play a twofold role and serve the function of spear-heading many oil-shale evaluation programs, as it could provide both cutting samples for assaying, geophysical data and modern well logs. This paper deals with a recent study conducted on Green River formation oil shale in which the application of induction, sonic and nuclear well logs to oil-shale evaluation was tested and proved. THEORY AND DEFINITIONS Oil shale may be described as siliceous marlstone, rich in solid organic matter called "kerogen". Kerogen is only slightly soluble in organic solvents, but it will decompose and yield oil vapors and gas when heated to destructive distillation temperatures at about 800 F. The mineral constituents of Green River formation oil shale are found in essentially uniform proportions with one another. The dominant types are, in the general order of abundance, dolomite, calcite, feldspars and quartz. Kerogen is also essentially uniform in its composition, and is about 80 per cent carbon and 10 per cent hydrogen by weight. The ratio of kerogen to the mineral constituents determines the richness or potential yield of the oil shale. This ratio also determines the total physical and chemical properties of the rock and provides a basis by which oil-shale richness may be determined from well logs. Because Green River formation oil shale was deposited in a lacustrine environment, the lithology is laterally consistent over wide areas. The vertical section consists predominantly of thin bands of alternating rich and lean oil shale which have been described by Bradley' as varves. The varves are occasionally broken by thin bands of volcanic ash and tuff and by zones of lean vugular oil shale. The effect that the thin non-oil shale beds and vugular zones would have on the well log analysis was a prime concern in the study. To cope with this possible problem, the logs used in the study were of two types: (1) logs believed to respond favorably to those properties of oil shale which are dependent upon the kero-gen-to-mineral ratio, these logs being the Gamma-Gamma Density log, the Sonic log and the Neutron log; and (2) logs that would respond to litho-logies and properties within the oil-shale section not associated with yield that might result in anomalous responses by the yield-measuring logs. Logs of the second type were the Gamma-Kay log, the Induction log and the Caliper log. THE PRESENT STUDY The present logging study was con-

By Nichols J. Grant, Bill C. Geissen

In low temperature phase diagrams, liquidus curves below about 1500°C are relatively easily established, e.g., by thermal analysis or separation of coexisting solid and liquid phases, followed by chemical analysis. Experimental difficulties increase considerably at higher temperatures and in systems involving more reactive metals. Although there are now thermocouples available for use from 1600" to 2400°c, as summarized by Caldwell,' the need for frequent calibration, aging, and contamination problems, and unavailability of suitable protection tubes has sharply limited their use at higher temperatures. Many of the high melt- ing metals are found to react with refractory oxides. TO avoid such problems, a frequently used procedure is the diffusion and saturation method, as described by Spedding et a1.' for the system La-C. This technique involves the annealing of one metal or a suitable alloy in a crucible of the other element at a temperature above the melting point, followed by chemical analysis of the center of the melt, after equilibrium is established. Further, if an alloy system is to be investigated employing the electron microbeam probe, and calibration charts have been established, it may be possible to measure the alloy concentration at the center of a cored as-cast structure, and to conclude from this points on the liquidus curve in a manner similar to the one to be described. It is known that in phases with a broad homogeneity range the rapidly cooled, cored, as-cast structure of an alloy presents concentrations having different lattice constants; this spread of lattice constant values contributes to the broadened lines of a powder pattern for the as-cast condition. The region of the crystal which is first to solidify will then correspond to the edge of the lines if the change of the lattice parameters with concentration is monotonous. In the course of the determination of the Ta-Tr phase diagram,3 it became evident that such behavior made it possible to construct the

Jan 1, 1963