Search Documents

By J. R. Wylie, L. C. Huntley

Drilling for oil in the eastern producing states was fairly active during the first part of 1931, although less so than in 1930. With low prices development declined during the year, until the low prices of the summer resulted in an almost complete shut-down of drilling. This coincided with the action of the Conservation Board of the Pennsylvania Crude Oil Producers Assn, in limiting pipe line runs to 50 per cent of the 1930 normal for the Bradford district and upper country, and to 70 per cent for the balance of the region. Not only was new drilling halted but in many cases oil-producing properties were shut in. In November crude prices were partly restored, and all oil offered was being taken except in the Bradford district which was restricted to 80 per cent of the 1930 normal. During the latter part of the year drilling was being resumed on a moderate scale, and new production indicated a resumption of the proration order. The interest in gas development which has been under way for several years, maintained its supremacy over the search for oil in 1931. New reserves of importance were developed during the year in the Western Kentucky Coal Basin, in the Eastern Kentucky shale gas territory, in Stark County, Ohio, as well as the Oriskany sand development in northern Pennsylvania and central New York. A gas line was completed to the Eastern Seaboard serving Washington and Baltimore, and other lines were under construction designed to serve portions of the territory not hitherto supplied with natural gas. The low price of fuel oil at seaboard is understood to be the deterrent factor against further extension of natural gas lines to these markets at present. The development of these new reserves, as well as those developed by intensive drilling in old areas, resulted in the building up of large potential gas production and a lowering of rates paid to the producer. This, coupled with the country-wide tendency to lower the consumer rates of all public utilities, resulted in a general threat to reopen rate cases before various state commissions. Oil Development The past year was marked only by the almost complete shut-down of new development, reaching its low point during the summer, with its

Jan 1, 1932

By W. J. Hillenbrand

The soda-ash method for eliminating arsenic from a molten copper bath has been described previously in some detail.' Briefly, the process consists in blowing powdered sodium carbonate under the surface of the partially oxidized melt and in removing the slag formed, which will contain a certain proportion of the arsenic formerly in the bath. Sodium carbonate melts readily at the temperature of molten copper, and when molten it dissolves arsenic oxide rather rapidly. In the process, sodium arsenate is formed which is removed along with the excess of molten soda ash. In order that arsenic may be eliminated in this way, it must first be oxidized to the pentavalent condition. This, however, is easily accomplished by blowing air into the molten copper until a fair excess of cuprous oxide is present. The manner in which soda ash is introduced into the furnace has a considerable effect upon the efficiency of the process. In the earliest attempts at arsenic removal, soda ash—often in combination with slaked lime, for sodium carbonate is not the only solvent that will remove arsenic—was thrown upon the surface of the bath, was allowed to melt, and was removed after it had dissolved a sufficient amount of arsenic. At present powdered soda ash is generally blown in under the surface of the melt with the aid of compressed air. Melting immediately as it comes into contact with the molten copper, it can react with considerably more of the bath than by the former method, and thus can remove arsenic more rapidly and more completely. Since the resulting slag is removed at once, its very destructive effect upon the furnace refractories is minimized. The effectiveness of the soda-ash method may be gathered from the results of the following test. A 900-lb. charge of copper was melted in a small, oil-fired reverberatory furnace, and sufficient metallic arsenic was added to the bath to bring the concentration of that element to about 0.5 per cent. Air was blown into the melt until its oxygen content was just under 1 per cent by weight. The bath was then sampled and soda ash was blown in under the surface in 5-lb. batches. After each addition

Jan 1, 1934

By S. Frederick Ravitz, Kenneth E. Fisher

Four liquids are ordinarily present in the lead blast furnace during lead smelting. At the bottom is the lead bullion, which is metallic lead containing about one per cent of impurities, including gold, silver, copper, bismuth, arsenic and antimony. Above this is the speiss, which consists essentially of arsenides and antimonides of iron and copper. The speiss is followed by the matte, which consists principally of sulfides of iron, copper and lead1. The top layer is the slag, of which the major constituents are silica, lime, alumina, zinc oxide and iron oxide. Similar products are obtained from the dross furnace, which treats the dross obtained in decopperizing lead bullion. The distribution of gold and silver among these various products is of considerable importance in the smelting of lead. In general, the matte and speiss cannot be treated in the lead smelter, and usually are sent to a copper smelter. It is usually desirable, therefore, to keep their gold and silver contents as low as possible, and to collect the precious metals in the bullion. If the bullion, speiss, matte and slag exist together in equilibrium, the gold and silver should distribute themselves among these four liquids in a definite manner, which, other conditions being equal, should depend only on the amounts of gold and silver in the charge to the furnace. It is thus apparent that a knowledge of whether such equilibrium exists is necessary before attempting to study the effects of various compositions of matte and speiss on the distribution of gold and silver among the furnace products2. Moreover, systems consisting of four liquids in equilibrium are very rare, and are of considerable scientific interest. In order to ascertain whether equilibrium existed, the distribution of gold and silver among the four liquids was determined. The speiss,

Jan 1, 1937

By R. A. Bowen

The Montreal mine, operated by the Montreal Mining Co., is four miles west of Ironwood, Mich., in Iron County, Wisconsin. It is the westernmost producing property on the Gogebic Iron Range of the Lake Superior district. Its production is 4000 tons of hematite per day from an average depth of 2300 ft. This tonnage is hoisted through a five-compartment vertical shaft. Several mining methods are in use but in the larger orebodies the method is sublevel caving. ORE Occurrence and Chaeacteristics The main orebodies of the Montreal mine lie in eastward-pitching troughs formed by the intersections of intrusive dikes with impervious members of the iron formation. The formation has an average width of 425 ft., strikes east and west and dips north at approximately 62. The dikes dip south at 45° and bear north 20' from the strike of the formation, making the intersections with various members pitch east at 16°. The dikes are not continuous across the formation but are interrupted by a longitudinal bedding fault, which has a throw of 380 ft. vertically and 885 ft. horizontally. North of the fault zone the formation is called "hanging," south it is called "footwall" formation. The faulting has created two ore-bearing horizons; viz., at the intersection of banging dikes with the slate members and the foot dikes with the quartzite footwall. In each formation the main ore-bearing member consists of wavy beds of hard chert interlaid with hematite. In the most productive part of the mine, where the sublevel caving method is employed, a hanging-formation dike lies in juxtaposition with a footwall dike and the iron formation carries ore in certain sections from the quartzite footwall to the hanging dike. Here a horizontal section of the orebody may be 300 to 400 ft. wide for a length of 150 ft. or more and tail out lengthwise in both the foot and hanging formations. The footwall ore section is much longer than the hanging wall because of the orebody's greater height above the "pitching dike."

Jan 1, 1940

By R. A. Bowen

The Montreal mine, operated by the Montreal Mining Co., is four miles west of Ironwood, Mich., in Iron County, Wisconsin. It is the westernmost producing property on the Gogebic Iron Range of the Lake Superior district. Its production is 4000 tons of hematite per day from an average depth of 2300 ft. This tonnage is hoisted through a five-compartment vertical shaft. Several mining methods are in use but in the larger orebodies the method is sublevel caving. ORE Occurrence and Chaeacteristics The main orebodies of the Montreal mine lie in eastward-pitching troughs formed by the intersections of intrusive dikes with impervious members of the iron formation. The formation has an average width of 425 ft., strikes east and west and dips north at approximately 62. The dikes dip south at 45° and bear north 20' from the strike of the formation, making the intersections with various members pitch east at 16°. The dikes are not continuous across the formation but are interrupted by a longitudinal bedding fault, which has a throw of 380 ft. vertically and 885 ft. horizontally. North of the fault zone the formation is called "hanging," south it is called "footwall" formation. The faulting has created two ore-bearing horizons; viz., at the intersection of banging dikes with the slate members and the foot dikes with the quartzite footwall. In each formation the main ore-bearing member consists of wavy beds of hard chert interlaid with hematite. In the most productive part of the mine, where the sublevel caving method is employed, a hanging-formation dike lies in juxtaposition with a footwall dike and the iron formation carries ore in certain sections from the quartzite footwall to the hanging dike. Here a horizontal section of the orebody may be 300 to 400 ft. wide for a length of 150 ft. or more and tail out lengthwise in both the foot and hanging formations. The footwall ore section is much longer than the hanging wall because of the orebody's greater height above the "pitching dike."

Jan 1, 1940

[Steel, iron which is malleable at least in some one range of temperature, and in addition is either (A) cast into an initially malleable mass ; or (B) is capable of hardening greatly by sudden cooling ; or (C) is both so cast and so capable of hardening. Variety A includes also molten iron which, if cast, would be malleable, as do its two sub-varieties, "ingot-iron" and "ingot-steel." (Tungsten-steel is malleable only when red-hot.)] does not seem to fit perfectly the requirement that it shall include all known varieties of steel and exclude everything else. The first requirement, that it shall be malleable at some temperature, is also possessed by some varieties of gun-iron—that is, mottled castriron, of which cannons have been made in the past by the South Boston Iron Co. and others. Gun-iron also meets the requirement (A) in being cast into an initially-malleable mass. The malleability was indeed not great, nor mas it made use of except to demonstrate the quality of the iron, but it approached in measurable degree that of some of the alloy-steels. As for requirement (B), some puddled-irons having from 0.2 to 0.3 per cent. of carbon may be hardened greatly, although this property is [lot utilized.

Jan 1, 1909

By George Wolff

To THE average person, the purport of the items and figures on the balance sheet of a mining company are hazy and the real financial condition of the company is cloaked in obscurity. It is also likely that the satisfaction of the stockholder in his investment, as well as the determination of the prospective investor, rests more on the reputation of the company, his confidence in the management, the stated earnings per share and the dividends paid, than on a comprehension of the information contained in the balance sheet. The balance sheet of any company at best can only closely approximate the true financial condition as of a given date. Any item of asset, except cash, can probably be altered if another's viewpoint is applied. It is difficult and expensive to drill and explore an orebody to determine the entire tonnage of ore therein. Those inherent difficulties render it practically impossible to prepare an absolutely correct balance sheet of a mining company. It is possible, however, to present the facts of a mining company more intelligently and comprehensively than is usually done. With this, in mind, a balance sheet of an imaginary mining company is submitted, with supporting schedules. The same fundamental principles hold true whether we consider a large or a small company. Less complexity is involved in dealing with the affairs of a smaller company. Therefore, for this purpose, the assumed company operates but two mines and a smelting plant. It has been deemed advisable to introduce the features of the operation of a mine acquired prior to March 1, 1913 and one after that date. The presentation therefore is concerned in one mine with the appraisement as of March 1, 1913 and in the other with the appraisement by reason of discovery. A consequential factor pertains to dividends paid from depletion reserves and therefore free of surtax to the stockholders. While supporting schedules, when necessary, give details of certain items on the balance sheet, it seems desirable to give further explanations with respect to some of them. This seems to be important because some mining companies do not treat the items as indicated on the statements submitted.

Jan 1, 1928

By Charles W. Wagner

A premature explosion might be described as an explosion that, occurs before the miner expects it. Notwithstanding that it is unexpected, a premature is generally within the miner's control. A hangfire explosion is a blast that occurs after the miner expects it,, and in all instances, except where the explosives or blasting accessories are defective, hangfire explosions are within the miner's control. Causes of Premature Explosions Generally, there are seven methods of shot-firing in anthracit,e mines; namely: (1) cap and fuse with dynamite, (2) fuse with pellet powder, (3) squib with black powder or pellets, (4) exploders and delays with dynamite or black powder, (5) exploders with dynamite, (6) delay ignitors with black powder or pellets, (7) electric squibs with black powder or pellets. Cap and Fuse.—This method of firing seems to produce the greatest number of premature explosions. This is not solely because of the method, but is the result of mispractices which are possible with this method of firing. The two most common mispractices followed with cap-and-fuse blasting are the firing of multiple holes and the use of short fuse.. In the firing of multiple holes by cap and fuse, investigations have shown that in nearly every instance where the miner was injured by this method of firing he remained too long at the face lighting the several fuses, so that the first shot went off before he could reach a place of safety. Such accidents could have been avoided either by accurate judgment by the miner of the relative lengths of the fuses or by the use of electric firing. Rules exist in nearly every mine forbidding the lighting of more than one hole at a time where the cap-and-fuse method of firing is practiced. Where it is desirable to fire more than one hole at a, time, electric firing should be used. It is difficult to understand why so many premature explosions result from the use of short fuses, inasmuch as the cost of fuse is practically a negligible item in the expense of a day's work. Notwithstanding this, however, we frequently find miners using short lengths of fuse in an effort to save one or two cents per hole, or about 15 to 20 # in a day. A practice

Jan 1, 1931

By Howard L. Hartman

6.1-1. Introduction. Of necessity, the first of the unit operations conducted during the exploitation phase in surface mining is production drilling. It precedes blasting, with which it is associated as the two unit operations employed to break or fragment consolidated material (usually rock) in place. The purpose of production drilling is to provide the cavity for placement of the explosives. So far, no alternative to blasting has been devised for fragmenting very resistant rock in situ, although some forms of excavation (ripping, bucket wheel) are suitable without prior blasting for softer rock, such as weathered shale or mudstone, decomposed sediments, etc. For the vast majority of surface mines, however, drilling and blasting are pre- requisite to excavation and essential to the production cycle. Drilling is also used in surface mining for purposes other than providing blastholes. It finds application during exploration for obtaining samples and during development for drainage, slope stability, foundation testing, etc. Only in the exploitation phase of surface mining, however, are unique or specialized drilling methods and equipment employed; and the discussion in this Section is directed primarily to that application of drilling. Drilling is the most common means of rock penetration, the operation of placing a directed hole in rock. Closely akin to drilling for exploitation purposes is the cutting or freeing of dimension stone in quarrying. This operation, usually termed channeling or sawing, also takes the form of directional penetration of rock; but instead of producing a cylindrical hole, it yields a kerf or cut. The material thus freed from the solid is both a shaped and sized product, an objective of vital importance in the dimension stone industry. In sawing, holes are sometimes drilled to insert tools, but this drilling is a minor part of the sawing operation and employs conventional methods. Cutting, as a unit operation for freeing stone in quarrying, may be considered equivalent in purpose to drilling and blasting in other forms of surface mining.

Jan 1, 1968

By W. C. Schroeder

During the post-war period, and particularly during the past few years, coal production has been maintained at a reasonably constant level. This is in contrast to the greatly expanded demand for oil and natural gas. Certain markets for coal, such as the railroad and for home heating, have tended to decrease, but this decline has been offset by an increase in demand for other uses, particularly for electric power. Since the United States has very large reserves of coal and relatively limited reserves of natural gas and oil, from the conservation viewpoint, it would be better if the increased demand were to fall more heavily on coal. Where coal has lost certain markets, the decision has not always been made on the basis of price, and, in fact, in many instances, the markets have been lost where coal could show a price advantage. There are various reasons for this situation but it can be attributed in the main to the preference of certain consumers for the convenience offered by liquid and gaseous fuels. In the production of chemicals such as benzene, phenol, or ammonia, coal still plays an important role. As co-products from coke-oven operations, a wide variety of aromatic chemicals are available. In recent years, however, the production has not been sufficient to supply the demand, and it is not profitable to build coke ovens to make chemicals unless there is a market for the coke as well. As a result, the petroleum industry is beginning to take a stronger part in the production of aromatic chemicals. Natural gas has almost displaced the coke-oven water-gas machine for the production of hydrogen for the synthesis of ammonia, as well as for the synthesis of methyl alcohol and other oxygenated compounds. This information is not new and is given here only as a basis for the discussion of the broad significance of the development of the gasification process. It is clear that if coal is to regain some of its old fuel markets, as well as to maintain a position in the field of chemical synthesis, processes must be available for converting coal to the type of fuel the customer wants, and for a cheap method of furnishing gaseous raw material to the chemical industry. The operation of coke ovens and water-gas machines is not the answer to this problem for at least two important reasons: (1) the limited supply and relatively high price of good coking coals, and (2) the relatively high costs of the combined operations of coking and manufacture of water gas.

Jan 1, 1953

By C. W. Price, G. A. Wheeler

BERYLLIUM has always been a difficult material to prepare for metallographic examination. Severe surface deformation occurs during mechanical grinding and polishing, and a suitable bright-field etchant has not been developed. Certain electrolytic techniques produce satisfactory polishes, but these techniques have not yielded entirely consistent results. Furthermore, they have not provided satisfactory bright-field etches. The purpose of this paper is to describe an electrolytic polishing technique that can also provide an excellent bright-field etch. In addition to the bright-field etch, other advantages of this technique are excellent reproducibility, rapidity, and ease of polishing and etching. Experimental Technique. Specimen Preparation. Beryllium specimens may be either mounted or unmounted for the use of this technique, and the size of the specimens is not important. Specimens with surface areas up to 4 sq cm have been electrolytically polished and etched successfully with this technique. The most important requirement is to provide a good electrical contact to the specimens, preferably on the back of the specimens. When specimens are mounted, a hole is drilled through the back of the mount so that the specimen can be contacted with a probe. Conventional metallographic grinding techniques are used to prepare the specimens for electrolytic polishing. The specimens are ground on silicon carbide papers. Grinding through the usual series of papers down to the 600-grit paper is recommended to minimize the electropolishing time, although successful electrolytic polishes and etches have been obtained by grinding only through the coarser papers. A continuous flow of water is used during grinding to provide lubrication and to minimize contamination. Mechanical polishing is not required because high rates of material removal are achieved with the electrolytic polishing. Polishing. Most of the results reported in this paper were obtained with a "Disa-Electropol", manufactured by Struers Scientific Instruments of Copenhagen, Denmark. Satisfactory results have also been obtained with the conventional beaker technique of electrolytic polishing, however, the conditions applicable to both the Disa unit and the beaker technique will be described. Stainless-steel cathodes are used in both techniques. In the beaker technique, a flat cathode, with an area at least twice that of the specimen, is used, and the specimen is held parallel to the cathode. The distance between the specimen and the cathode affects the quality of the electropolish. This distance is set at about 7 mm in the Disa unit; the same distance produces the best results in the beaker technique. Specimen-cathode distances greater than about 20 mm produce considerable relief, while distances less than 7 mm cause high current densities that are difficult to control. An electrolyte of 2 pct HC1, 2 pct HNO3, and 2 pct HCIOl in ethylene glycol gives the most satisfactory results for both electrolytic polishing and etching. This electrolyte was developed by altering the composition of a similar electrolyte used for electrolytic lapping1 and adding HClOl to improve the etching characteristics of the electrolyte. Variations of from 0.25 pct to as much as 5 pct of each of the acids do not significantly affect the results, but the greatest amount of control and reproducibility can be obtained with the composition of 2 pct of each acid. Generally, lesser amounts of the acids produce lower polishing and etching rates, while greater amounts of acids cause high current densities that are difficult to control.

Jan 1, 1968

By L. D. Jaffe, John H. Hollomon

Fox many steel parts it is desired to obtain the maximum toughness consistent with the strength required by the mechanical design. It is generally recognized that the greatest toughness at any given strength is found in steels having a tempered martensitic structure,1 and is virtually independent of the composition of the steel2 (except for carbon). The choice of the composition of a steel for the parts in question should be based, therefore, on hardenability considerations and on manufacturing facility and economy. In a recent paper3 the concept of hardenability was discussed and a somewhat new approach to the problem was suggested. The hardenability was defined in terms of the cooling conditions (speed of cooling) required to avoid the pearlite and the bainite reactions. Since all the alloying elements do not have the same effects on the two reactions, the bainitic and pearlitic hardenabilities must be considered separately. In order to design a steel for a given part, it is necessary to design a composition that has both sufficient pearlitic and sufficient bainitic hardenability. However, this requirement does not fix the combination of alloying elements to be used; an infinite number of steels would have the required hardenabilities. Other considerations limit the choice. For example, decreasing the carbon content increases the toughness at a given hardness, and for this reason low-carbon steels are often desired. Limitations or requirements of refining, casting, or forming practices often affect the level of some of the alloying elements. Price considerations enter. Frequently, however, it is very desirable to minimize the tendency toward quench-cracking while maintaining the necessary hardenability. This paper is concerned with suggesting a method for choosing compositions that will have the required hardenability together with minimum tendency toward quench-cracking. QUENCH-CRACKING Since only the case in which the entire part will transform to martensite in the particular quench employed is being considered, the analysis of the quench-cracking problem is somewhat simplified. Quench-cracking arises from the temperature gradients existing throughout the piece during cooling. Because of these temperature gradients, the contraction arising from the decreasing temperature and the expansion arising from the austenite-martensite reaction do not occur uniformly over the parts, and stresses are set up that tend to cause cracking. The temperature gradients can be reduced by decreasing the severity of quench. This, however, requires that the hardenability be correspondingly increased by increasing the carbon or alloy content. An

Jan 1, 1946

By George Jones

MACHINE mining on the pitch plays an important part in the produc-tion schedule at the Salem Hill Colliery of the Haddock Mining Co. This mine is just outside the city of Pottsville, in Schuylkill County, along the southern border of the Anthracite Region. The entrance to the mine is through a cross-measure tunnel 15 ft. above water level and running north 1500 ft. until it strikes the Rabbit Hole vein, where the machine mining is carried on. The main slope, dipping south, was sunk 1200 ft. in the Rabbit Hole vein with levels turned off at 300-ft. intervals. The vein is from 24 to 30 in. thick on a varying pitch of 20° to 40°. The overburden has differed from 50 to 466 ft., the most recent work having the maximum overburden. Immediately over the Rabbit Hole vein is a seam of soft sand slate from 1 to 4 ft. thick which presents a problem at times because it dis-integrates rapidly when exposed to the air. It will crack up and fall without any audible warning, therefore the workmen must always be on the alert, watching for loose slabs. The main top is sandstone, vary-ing in thickness from 8 to 20 ft. The bottom rock is similar to the top, but is finer grained and subject to a more complete disintegration. The vein has a 3 to 4-in. shelly band along the bottom, and all under-cutting has been done in this soft band.

Jan 1, 1935

By K. V. S. Sastry

INTRODUCTION Flotation is by far the most important unit operation of mineral processing. Most of the common base metals are produced from flotation concentrates of metal sulfides. Flotation is proving to be a valuable process for producing non-metallic minerals such as ceramic oxides, silicates, clays and phosphate fertilizers. All these fltation separations are carried out on materials which are predominantly in the 10 to 100 micronssize range. The present practice of flotation circuits for the production of large tonnages of metallic and non-metallic mineral concentrates is fairly well understood, developed, and standardized. Two kinds of problems are encountered (1, 2) with fine particles smaller than 10 microns. First is the interference of the fine particles with the flotation of the coarser particles and the second is the poor flotation behavior of fine particles. In general, these problems are handled either by eliminating, minimizing, or ignoring the fines in the flotation circuit feed. In recent years, however, a considerable number of experimental and theoretical studies have been carried out to understand the flotation behavior of fine particulates. This literature is summarized in four review papers (2-5). Application of the conventional flotation techniques for the separation of mineral fines is known to be uneconomical, and to present several scientific and technological problems (1-5). The objective of this presentation is to examine the flotation behavior of fine particles in terms of their physical-chemical properties and to review the potential techniques of fine particle flotation. Specific reference to the problem areas and research needs will also be included in the discussion.

Jan 1, 1979

By S. A. Wookey

More than 90 per cent of the ore produced by stoping at McIntyre is mined by horizontal cut-and-fill methods. The remainder is mined by square set and fill. In the stopes on the upper levels, mill holes are spaced 80 ft. apart and usually it is feasible to mine the breast for the full distance between the mill holes in one operation and to break, clean out and fill without any support for the roof or walls, other than the odd crown bar or sprag. The ore is scraped to the mill holes by small (10 to 15 hp.) air-operated slusher hoists. No grizzlies are used over the chutes and care is taken to break up the big pieces beforehand. Fill usually is spread by tramming sand or waste in a one-ton car from the fill raise. Fill raises are driven parallel to the strike of the vein and are inclined at approximately 48°. In long stopes, where more than one fill raise is necessary, they are spaced about 300 ft. apart. It is sometimes necessary to stand square sets for a short distance each way under the brow of the fill raise. support needed increases and on the lower levels and in some wide stopes where closer support of the back is necessary, it has become standard practice to timber the stope with 12 by 12-in. timber. Rough timber sets consisting. of caps, tightly blocked to the back and supported on posts 7 ft. high, are placed at about 5 ft. intervals. These sets are generally salvaged from the lower breast before blasting and are used again on the upper slice after the fill has been placed. In general, two or three breasts may be broken down before mucking out and filling and the ground stands long enough to enable this to be done safely. On the lower levels and in certain wide stopes and in heavy ground, a more intermittent method must be used. Only one breast or even part of a breast can be blasted and the back must be timbered before the ore can be removed. In these cases, sill timbers 16 ft. long, supported at one end on posts from the fill and at the other end on pins inserted in holes drilled in the face, are used. Timber cribs 5 by 9 ft. built from the fill to the roof and tightly blocked to the back are used throughout the mine to reinforce both the timber sets and the square sets.

Jan 1, 1946

By Campbell Osborn

From the viewpoint of practical economic engineering the main value in studies of demand and supply lies in the information they give concerning the next movement of price. The title of this discussion is too comprehensive for detailed analysis and it will, therefore, be narrowed to the question of price measurement. The oil operator is interested primarily in net profits. Prices, costs and production determine them. Production is here used in its broadest sense. It includes refining and marketing. It is an operating problem. Prices and costs are economic considerations. Though costs are an important element of prices and profits, the subject is too large to be treated in a brief paper of this sort. In the long run, costs govern prices, but for the purpose of gaging prices in the immediate future the relationship of current demand and supply are more significant. Operating, expansion, retrenchment, sales and storage policies of oil companies are largely influenced by the feeling of executives concerning this relationship. The stockholders of companies whose executives are wrong may suffer. Investors who err in their judgment may likewise lose. On the other hand, oil companies and investors who appraise these factors correctly and move accordingly will profit. It is an important subject worthy of careful consideration. The author has been asked to discuss the subject for 1928. From the beginning of the year until the first of June, as illustrated by Fig. 1, over-supply prevailed in the face of restricted production, but from June to September, with record consumption, demand slightly exceeded supply and oil came out of storage in the United States as a whole. One of the main problems of the oil man is to decide whether this condition will continue and what the next movement of prices will be. Before he can do so he must have an understanding of the underlying conditions and of the facts that led to the present situation. With these facts in mind he is in a position to measure the effect of the present relationship of demand and supply on price and is afforded a perspective that may enable him to look ahead for a short period of time. The practical

Jan 1, 1929

By V. D. O’Leary

The Anaconda Co. has two economic uses for the drainage water from its underground mines in the district of Butte, Mont. One is the precipitation of copper, which the company has been accomplishing at the Leonard precipitating plant for many years, and the other is the leaching of the Berkeley pit discard, where millions of tons of leach material have accumulated. The acidic mine drainage water is an ideal leaching medium for the latter purpose, but the solids and colloidal material suspended in the water must be removed before it can be applied to the low-grade Berkeley leach dump. For this reason, it is important for Anaconda to have an efficient means of cleaning mine drainage. Such a means has been found and tested at one mine and is now to be incorporated in a new central pumping station the company is planning at the 3900-ft level of the Kelley mine. This plant is to be activated in early 1967 and will replace the antiquated four-lift High Ore mine pumping plant which was designed and installed before tailing backfill was adopted. The new plant will feature eight pumps with a total capacity of 8000 gpm in a single lift against a total dynamic head of 4100 ft. For the most efficient and economical operation of the plant it is imperative that all possible mud be removed from the drainage water before pumping.

Jan 9, 1966

By W. E. Thorne

The object of this graphic method is to estimate the weight of the casting, which is to be made from a given pattern, when the cross-section is not a uniform geometrical figure. Such an estimate is a very important guide to the foundryman, who would otherwise guess at the probable weight of a casting of new design, and, in trying to be on the safe side, would probably melt an unnecessary amount of iron. It is also an aid to the designer of a new car-wheel pattern, who must otherwise estimate from general experience the probable weight, have test-wheels made, and correct the pattern afterwards, so as to obtain the weight prescribed. For the method here described, an accurate drawing of the pattern is employed. This gives a closer result than a drawing of the wheel itself, for the following reasons: 1. Calculations based upon the actual dimensions of the wheel involve the erroneous assumption that the specific gravity of the casting is uniform throughout; and upon that basis the calculated weight would be wrong, because the amount of metal poured has shrunk in the mould, acquiring the highest density in the outside chilled portion, and growing less dense through the mottled to the gray portions. 2. Calculations based upon the dimensions of the pattern or " chiller " assume that the cooled metal will not have shrunk, but will have the volume of the pattern and a uniform density. These assumptions, though erroneous, counterbalance each other. For instance, the patterns and the chiller which give a wheel 33 in. in diameter when cold, are respectively 33.5 in. in diameter. This shows a shrinkage for wheel-iron of about & in. (ordinary gray pig is commonly assumed to shrink about 1/8 in.) per foot. Wheels cast in 33.5-in. chillers do not always have the

Jan 1, 1903

By AIME AIME

Air transport supplants the old methods. The 3-piece canoe fits in the plane and likewise makes possible not a bad division of labor over a 5-mile portage

Jan 1, 1933

By D. H. Gray, G. Bergamini, I. Fatt

A method developed by soil scientists for measuring permeability anisotropy of soils has been adapted for use in studies of sandstone permeability aniso-tmpy. Studies on Berea and Bandera sandstone show that permeability of these materials decreases upon application of simulated overburden pressure. Permeability reduction of Berea and Grubb sandstone cores subjected to simulated overburden pressure is shown to be a function of the ratio of radial to axial stress. INTRODUCTION The effects of mechanical stress on reservoir rock parameters are now generally accepted as being important in reservoir engineering calculations. In several oil fields the unique behavior of the reservoir has been attributed to the influence of overburden pressure or internal fluid pressure on rock permeability or fluid content. l Although the gross effects of overburden pressure on permeability, porosity, waterflood efficiency, electrical resistance and sonic velocity have now been established,3-9 there are some very interesting, and perhaps important, details of rock behavior under stress that have not heretofore been studied. In this paper we will show that permeability anistropy of several sandstones is a function of overburden pressure. We will also show that permeability reduction of cylindrical samples of two sandstones, when subjected to mechanical stress, is a function of the ratio of radial to axial stress. Most studies of overburden pressure effects made in the past have attempted to duplicate reservoir conditions by applying hydrostatic external pressure on all surfaces of the sample. Assuming perfect elasticity, that is, no viscoelastic flow during geological time, reservoir rock in situ cannot be under hydrostatic stress as is apparent from the value of 0.25 for Poisson's ratio for most rock. In the absence of tectonic forces the horizontal stress component If there are directional permeability effects, as has been reported from field and laboratory studies, l0,11 then one would expect hydrostatic stress as used in the laboratory to give a different permeability reduction from that occurring under reservoir stress conditions. The influence of stress on directional permeability was measured by a modification of the method first described by Maasland and Kirkham for use on soil samples.12 Their method permits calculation of the permeabilities along each of the three mutually perpendicular axes of a cubic sample. The modification reported in this paper extends the method to observing these permeabilities when the sample is under hydrostatic stress. The Hassler sleeve type of core holder is satisfactory for studying overburden pressure effects on permeability if a known force is applied to the end plugs. Wyble6 used a sleeve core holder but did not load the end plugs. In this paper we combine sleeve pressure and axial force to give permeability changes which we believe are close to those occurring in reservoirs when reservoir pressure changes. The combination of sleeve pressure and axial force assumes, however, that the sleeve pressure simulates both vertical stress and horizontal stress in one direction. METHOD PERMEABILITY ANISOTROPY The Maasland and Kirkhaml2 method of measuring permeability anisotropy uses a cube of porous material which is Open On three faces and has discs with a Center hole for an air inlet cemented to the other three mutually perpendicular faces (Fig. 1). The rate at which air pressure falls in a bottle of known volume, and pressure slightly above atmospheric, when the bottle discharges through each disc, is