Search Documents

By W. I. Garms, J. L. Stevens

Because of the many conflicting opinions regarding the functioning of the ball load and the characteristics of ball wear in ball-mill grinding, the following résumé of reports covering recent tests conducted at the Hayden plant of the Kennecott Copper Corporation is submitted with the view of pointing out certain salient features that should throw additional light on the subject. Mills Used Cylindrical drum mills with trunnion feed and discharge were used. The discharge trunnion was 13½ in. in diameter. Dimensions inside the lining were 6 ft. 6 in. in diameter and 9 ft. 6 in. long. The mills were Britannia-lined and nine lifter bars projected 2 in. from the lining. The mill speed was 162/3 r.p.m. Feed to the mill was 9 per cent on 10-mesh, 85 per cent on 100-mesh, 77 per cent solids. New balls measured 2 in. in diameter and the approximate weight of the ball load was 40,000 pounds. Initial Test During a test that was being conducted to determine the relative economic value of standard cast balls vs. forged steel balls in the local 'grinding operation, certain observations were made in regard to the functioning of the various ball sizes and the characteristics of ball wear, which warranted a supplementary test for the purpose of confirming such observations. For the initial test, the necessity for developing a graduated load of the new forged balls before the test could be started was realized, but the time required to obtain a graduated load and the functioning of the various ball sizes was not clear. No advantage could be seen for starting out with a full load of forged balls, as this initial load, at the least, would have to be completely ground out and replaced by daily additions of balls before the graduation could be complete and a normal static condition of ball sizes reached. For a considerable period prior to exhaustion of this initial charge there would be an unusual quantity of worn balls of a certain size, which would not be typical of a normal charge and could influence the characteristics and functioning of the entire load. Therefore, it was decided to start by daily addition of the forged balls to a mill that contained a normal operating load of cast balls. After 88 days of operation the mill was shut down for inspection. By that time the load consisted of a mass of forged balls functioning around a large core of the residual material of the former cast-ball load. This core of cast slugs, locally referred to as "the kidney," was well defined from the forged-ball load.

Jan 1, 1947

Scraper With over 40 pet more struck capacity than previous models, the new Caterpillar No. 90 scraper is designed to increase earthmoving production when used with D8 tractor power. This scraper moves dirt with the aid of a hard surfaced, reversible cutting edge. Material is carried in a flat, doublebottom bowl of high tensile steel. Operation is by means [ ] of a cable-control unit, which can be mounted on the rear of the tractor to provide for positive loading and ejection. Tapered roller bearings are installed at each axle. The scraper uses two 24.00 to 29 front tires and two 27.00 to 33 rear tires, all four of 24-ply rating. When loaded, the scraper distributes 60 pet of the weight on the rear tires. Circle No. 1

Jan 1, 1952

Jan 1, 1964

By R. M. (Mike) Robb

Introduction The requirements to investigate a wide range of alternatives and analyze a variety of ‘what if’ questions make the automation of pit design a requirement in today’s rapidly changing mining industry. The wide-spread application of computers has relieved the engineer of much of the tedious and error-prone work related to mine design. He is thus free to do the creative and innovative thinking for which he is trained. It is now possible to investigate a large number of alternative pit designs in a reasonably short time period. In the past it was very easy for a team of engineers to consume 12 to 14 man-months in the detailed hand design of a large open pit. The pressure of today's mining industry, the desire to investigate a variety of alternative designs, and the shortage of qualified engineers make the slowness of hand design less preferred.

Jan 1, 1979

Detailed Geology of Certain Areas in the Mineral Hill and Warm Springs Mining District. By A. L. Anderson. T. H. Kilsgaard and V. C. Fryklund. Jr. Idaho Bureau of Mines and Geology. University of Idaho. 73 P. Maps, Illus.-Divided into three parts, this pamphlet covers the geology and ore deposits of the Hailey-Bellevue Mineral Belt, the Triumph-Parker mine mineral belt, and the ore deposits of the Mayflower Area. Numerous maps and illustrations are included for each area. Government Administration of the Copper Industry, World War 11. By John W. Douglas. 1950.51 P. $1.-This pamphlet covers in detail all the steps relating to control and operation of copper and copper products, and is of particular interest to primary producers, brass mills, wire mills, and foundries. Of particular current interest is the booklet's coverage of the steps leading to the Controlled Material Plan, into which industry is now once again heading. Copies can be obtained for $1 from John W. Douglas, Republic Foil & Metal Mills Inc., 55 Triangle St., Danbury, Conn.

Jan 12, 1951

By Nick Turner, E Walker, George C. Bowser

A fully field tested mine-wide data/communications system is presented which integrates total data acquisition, control, and instrumentation into a single system. Installations at Kitt #1 and Amonate Mines (W.Va.1 use an LSI-11 series computer which communicates with easily installed field data stations over a single twisted wire pair. Complete field test data are presented, identifying the problems and successes experienced in the development, installation, operation and maintenance of the system, and the training of mine personnel. Of particular interest is the system installed at Kitt #1 which has been in continuous use since February 1982. The paper will also deal with the application of a computer-based carbon monoxide monitoring system installed at the Amanate mine in September 1982. The purpose of that system is to monitor air quality and to provide early fire detection in the belt entry to permit the use of belt air for face ventilation.

Jan 1, 1983

By J. A. Herbst, D. W. Fuerstenau

The effect of mill speed and ball load on the dry ball milling of dolomite is examined in the context of the batch grinding model. Observed changes in the parameters of the model are interpreted, as far as possible, in terms of the mechanics of particle motion in the mill. A parameter estimation scheme previously proposed by the authors is shown to provide the basis for a successful simulation of grinding behavior over a wide range of mill speeds and ball loads. Finally, a combination of experimental and simulated results is used to determine the optimum mill speedball load for closed circuit grinding in this mill-material system.

Jan 1, 1973

By William Newnam

WHEN Hugh Lee Pattinson discovered, in 1829, that the crystals formed during the slow cooling of molten lead were poorer, and the remaining liquid richer in silver, than the original lead, an important step was made in the metallurgy of this metal. Being the first process applicable to the desilverization of low-grade lead bullion, it soon found its way into all European countries having such a product to treat, thereby effecting the saving of many ounces of silver annually which previously had been thrown away. The old hand process was expensive, as viewed from the standpoint of more modern methods; the labor was great anti the tonnage was small, but on the other hand the results were fairly, satisfactory. This process flourished for some time after the introduction of the cheaper Parkes process in 1852 and it is still in use in a few European smelteries. Only one notable improvement was made on the original process, that of Luce and Roan at Marseilles, France. It consisted in the application of steam for stirring and the tapping of one-third of the liquid lead, through perforated plates covering the tap holes flush with the bottom of the kettle, thus leaving two-thirds in the form of crystals in the original kettle. This modification considerably lowered the operating costs as it permitted of much larger kettles, an increased tonnage and eliminated much of the slow, hard labor of the hand process.. The Luce and Rozan process has persisted in its original form to the present clay. Stephen Tredinnick, English born, spent most of his years around the Luce and Rozan plants at Marseilles and elsewhere in Europe, coming later to Eureka, Nev., in 1878, to operate the Luce and Rozan plant at that point. Mr. Tredinnick was a competent Luce and Rozan operator and being devoted to the process he firmly believed that with modifications the costs could be so lowered as eventually to supplant the Parkes process.

Jan 5, 1917

The Library of the above-named Societies is open from 9 A.M. to 10 P.M., except on holidays. It contains about 70,000 volumes and 90,000 pamphlets, including sets of technical periodicals and the publications of - scientific and technical societies members of the Institute, with few exceptions, are forced to spend a portion of their time 'in localities isolated from sources of information. To these the Library, through its Library Service Bureau, can render - valuable service through correspondence; letters requesting information will receive especial attention. The Library is prepared to furnish references and photographic copies of articles on mining and metallurgical subjects; to determine the existence of mining maps, and to furnish genera1 information on the geology and mineral resources of all countries. All communications should be made as definite as possible so that the information received may be what is desired and not include collateral matter which may not be of interest. The time spent in searching for such collateral matter will be saved, and the information will be sent more promptly and in more usable shape.

Jan 10, 1916

By John Birkinbine

IN all metallurgical processes and mining operations, water is an element which receives attention from the management ; and provision is required either for a means of supply, or for the disposal of accumulation. In many works the quantity of water to be furnished is sufficiently large to place the item of water supply of equal importance to the reception of material or disposition of product ; and the means to be employed receive, or should receive, the most careful investigation. There are exceptional cases where mines or quarries possess a natural drainage, but a large majority of the useful ores and the fuels delved from the earth are obtained from workings in which water accumulates and must be removed. Often the quantity to be

Jan 1, 1877

By John Birkinbine

In all metallurgical processes and mining operations, water is an element which receives attention from the management; and provision is required either for a means of supply, or for the disposal of accumulation. In many works the quantity of water to be furnished is sufficiently large to place the item of water supply of equal importance to the reception of material or disposition of product; and the means to be employed receive, or should receive, the most careful investigation. There are exceptional cases where mines or quarries possess a natural drainage, but a large majority of the useful ores and the fuels delved from the earth are obtained from workings in which water accumulates and .must be removed. Often the quantity to be

By F. O. Garrabrant, F. S. McNicholas, Robert Henderson, R. U. King

Several years ago, it was decided to experiment with the use of high-pressure water to bring in finger hangups and reduce the amount of secondary blasting necessary. It was argued that the velocity effect of the high-pressure water would bring down hangups without unduly wetting the ore. Water under a head of about 550 ft. was installed in certain slusher drifts. Ordinary ¾ in. water hose, with a nozzle opening of % in., was used, and water was impinged on the fines under a hangup. Results were excellent. About half the total number of hangups were brought in with high-pressure water without blasting and the cost of this part of the slushing operation was reduced about 50 per cent. Operations were speeded up, dust counts and safety hazards were reduced, and a more desirable working place was secured. The additional water added to the ore was under one per cent and caused no inconvenience in slushing, haulage, or crushing operations. Usually the ore would absorb all of the water, so that none of it would enter the loading drifts. The entire mine, developed by slusher drifts, is being equipped with high-pressure water. Heating Mine by Compressor Cooling Water Several years ago, the problem of heating certain sections of the mine during freezing weather became important. It was calculated that there was sufficient heat in the compressor cooling water to heat the incoming ventilating air current to above freezing, if such heat could be transferred from the water to the air. All schemes of radiation from pipe were rejected as too cumbersome, costly and impractical. It was thought that by spraying the heated water from the compressor cooling system into the incoming air, a satisfactory heat exchange could be accomplished. The only objection was that the sprayed water would freeze and might fill the air-intake drift. However, when water at about 75° to 80°F. was sprayed at the rate of 200 gal. per minute through a bank of sprays into the incoming and freezing air current, this air was thereby heated to above freezing; and although some ice was built up in the air drift, the amount was not objectionable. Occasionally the built-up ice was picked down into the outgoing water stream, which removed it. The entire south and westerly parts of the mine were prevented from freezing. Concreting for Hangups Considerable trouble was experienced in securing hangups of fine ore in slusher fingers that needed repairing. Regular methods of timbering were unsatisfactory. Now, a slab of concrete is poured over the top of the muck by Pumperete machine, almost filling a finger, which gives a satisfactory slab to work under for making the needed repairs. Derailers Some trouble has been caused by motor-men not observing safety lights and

Jan 1, 1946

By M. J. deBastiani, John Kostuik

The Denison orebody, located on the north limb of a syncline, rests at depths of 800 ft in the northern end of the property to 3000 ft at the southern end, and has a composite dip of 19º, varying locally from 0º to 45º. It is composed essentially of two pyritized conglomerate beds separated by a varying thickness of quartzite. The thickness of the upper conglomerate reef of the main ore zone varies from 2 to 15 ft while the lower reef is from 2 to 12 ft. Mining, whether carried out over the entire section of the reefs and quartzite or by selective mining of the reefs, is accomplished by room and pillar methods, with an initial 67% extraction on the advance towards the property boundaries. The underground ore handling requirement in such an orebody has become one of the most challenging problems in mining.

Jan 8, 1966

The Library of the above-named. Societies is open from 9 A. M. to 10 P. M. except on holidays. It contains about 70,000 volumes and 90,000 pamphlets, including sets of technical periodicals and publications of scientific and technical societies Members of the Institute, with few exceptions, are forced to spend a portion of their time in localities isolated from sources of information. To these the Library, through its Library Service Bureau, can render valuable service through correspondence; letters requesting information will receive especial attention. The Library is prepared to furnish references and photographic copies of articles on mining and metallurgical subjects; to determine the existence of mining maps, and to furnish general information on the geology and mineral resources of all countries. All communications should be made as definite as possible so that the information received may be what is desired and not include collateral matter which may not be of interest The time spent in searching for such collateral matter will be saved, and the information will be sent more promptly and in more usable shape.

Jan 5, 1918

By Joseph G. Franzone, Alan K. Kuhn, Jerry J. Oliver

INTRODUCTION Tailings produced by many uranium milling operations consist of fine sands with some silt and slimes. When fine sandy materials are placed by hydraulic methods behind an impermeable dam, they are deposited in a loose state and some portion remains saturated. These saturated, loose fine sands are highly susceptible to liquefaction, the phenomenon in which a monotonic or cyclic disturbance causes excess pore water pressure and, concurrently, a total loss of strength in the sand. Once liquefied, the fine sand flows, causing collapse of supported structures. The potential for such a liquefaction failure was identified and successfully treated at Sohio Western Mining Company's L-Bar Uranium Operations near Seboyeta, New Mexico. The Sohio tailings dam is an earthfill starter dam with tailings raises constructed upstream of the starter dam crest. Beginning with the start of mill operations in 1976, tailings were deposited hydraulically in the impoundment behind the starter dam. As the tailings level approached the crest of the starter dam, beached tailings were excavated and placed in lifts by a dozer to form two raises above the crest of the starter dam. As the impoundment has gradually filled with tailings, the decant water pond level has risen. Correspondingly, the water level in the tailings dam, upstream of the chimney drain, has also risen. By August 1980, the phreatic surface was above the crest of the starter dam and stability analyses indicated that the tailings dam did not have the safety factor of 1.0, under static loading with liquefaction, implicit in the 1980 New Mexico State Engineer's requirements. The problem related directly to the high phreatic surface in the loose sandy tailings behind a dam structure that was not capable of resisting failure which might develop in liquefied tailings. Two methods of stability enhancement were considered for the Sohio dam. One method was reinforcement of the dam using a clay buttress placed against the downstream slope. The other method was installation of horizontal drains through the starter dam to drain decant water and lower the phreatic surface. Either method would increase the stability of the dam. However, the comparative analysis of the methods indicated that horizontal drainage offered significant advantages in cost and could provide a more direct remedy of the source of the problem, the saturated section of tailings. In addition, a drainage system would be more amenable to modification and more quickly installed than a buttress. On the other hand, a clay buttress could be more directly controlled, would involve routine earthwork, and has successful precedent. Therefore, the buttress approach would involve less risk. After weighing the advantages of both methods and the costs versus risks, the horizontal drainage approach was selected. Consequently, a horizontal pipe drain system was recommended and designed (D’Appolonia, 1981a). This paper describes the design and installation of the drainage system and its initial performance. PIPE DRAIN SYSTEM DESIGN Design Criteria and Parameters To increase the stability of the dam to acceptable levels, the drainage system had to lower the phreatic surface behind the dam to the level calculated to give a minimum safety factor of 1.0 under conditions of liquefaction. In addition, the system needed to be essentially self-operating, easy to maintain, and economical. To accomplish these objectives, the following design criteria were established: 1. The pipe drains must lower the phreatic surface at least 4.3 m (14 ft.) at the midpoint along the dam (the deepest section) and by proportionately smaller amounts toward the abutments to satisfy safety factor requirements.

Jan 1, 1982

By R. H. Fillnow, D. J. Mac

IT has been demonstrated that alloys in systems structurally analogous to steel undergo reactions during heat treatment similar to those of steel, and yet very little work has been done on such systems, particularly from the standpoint of isothermal transformation. The literature shows that most of the isothermal work has been done on copper-alu-minum alloys.'-3 One paper has been reported on a eutectoid copper-silicon alloy,' and one on iron-nitrogen alloys.' There are no published reports of previous investigations on the isothermal transformation of a eutectoid beryllium bronze. At least two papers have been reported on isothermal age-hardening phenomena in beryllium-copper alloys of lower beryllium content.5,6 No information on eutectoid transformations in this alloy is given in Rimbach's book, "Beryllium." ' This paper reports the results of an investigation on the isothermal transformation characteristics of a eutectoid beryllium bronze. Materials Used and Procedure The eutectoid beryllium bronze used in this investigation was centrifugally cast at the Ampco Metal Co., Inc.. Milwaukee. Wis. A master beryl-lium-copier alloy, purchased from the Brush Beryllium Co., was used to make the beryllium addition to the copper. The alloy was melted under a protective carbon cover and Centrifugally cast into a graphite mold preheated to 920°F. Some trouble with segregation of beryllium in the melt was encountered but was eliminated by violent stirring during melting and pouring. Since very thin .specimens were used for the various heat treatments, only one casting of the four prepared was necessary for the complete isothermal study, thus eliminating any discrepancies caused by a change in composition. The analysis of this casting was 94.035 pct copper and 5.965 pct beryllium. A slight trace of iron was found. The castings were sawed into specimens approximately 3/32 in. in thickness. The specimens were first given an "austenitizing" heat treatment at 788°C, well within the single phase beta region, in a vertical tube furnace. The specimens were then quenched individually into an adjacent molten salt bath and held there for a definite time, after which they were quenched into water at room temperature. Temperature was held to ± 2°C in the salt bath. No homogenizing treatment was given the specimens other than the soak at 788°C. Despite the fact that this was a cast alloy, no evidence of segregation or coring was found in the microstructure of any specimen, either as cast or as heat-treated. Upon completion of the heat treatment, the speci-mens were subjected to metallographic examination

Jan 1, 1951

By S. C. Termes, R. L. Wilfong

As part of an effort to provide basic data on the fundamental scientific and engineering principles of minerals beneficiation, the Bureau of Mines is conducting research on the flocculation of mineral fines. This paper presents results of studies using cross-linked starches containing carboxyl, diethanolamine, iminodiacetic acid, and xanthate groups to flocculate hematite, goethite, chromite, manganite, pyrolusite, cuprite, and cassiterite fines. The carboxyl and xanthate derivatives flocculated all minerals except cassiterite; the latter was flocculated by only the diethanolamine derivative. The imlnodiacetic acid derivative flocculated hematite, goethite, chromite, cuprite, and pyrolusite fines. Zeta potential measurements were made to help define the reaction mechanism responsible for flocculation. These measurements indicate that electrostatic attraction probably is not involved, except possibly in the case of the diethanolamine derivative. The separation of hematite from quartz by selective flocculation with chelating crosslinked starches under two pH conditions and with two dispersing agents is described. Best recoveries and grades were found when either the carboxyl or xanthate derivatives was added at the natural pH of the pulp in the absence of a dispersing agent.

Jan 1, 1984

By J. M. Lohr

THE characteristics and uses of thermocouples of platinum and the platinum alloys being so well known, this paper will be confined to base-metal couples. During the past decade, there has developed a strong demand for thermocouples made of metals cheaper than the platinum alloys, and suitable for industrial heat measurements. Much research has been clone but only a very limited number of alloys have been found to possess the necessary characteristics for general technical use. In the development of thermocouple alloys it is necessary to consider the following points: The electromotive force and temperature relations; permanency or constancy; reproducibility; manufacturing difficulties; durability; and accuracy in use. The electromotive force developed by the thermocouple should increase with the rise of temperature according to some definite law. It is desirable that the electromotive force should vary directly with the temperature difference of its junctions, in other words, giving a curve linear or nearly so. It is also desirable that the resulting electromotive force be as large as possible for any given range of temperature, thereby insuring greater accuracy of readings.

Jan 9, 1919

By Michael E. Zellars

The environment for deposition of marine phosphorite is controlled by the relationship of prevailing climatic, oceanographic, structural, and sedimentary conditions. The set, or sets, of conditions that has evoked the accumulation of economic concentrations of phosphorite has been the subject of a number of previous works. Phosphorite presently considered ore is generally in excess of 10% P205 with an extractable phosphate product in excess of 30% P2O5. The concentration of the product in the ore, its amenability to state-of-the-art extraction, and thickness of the overburden are major controlling factors in determining its mineability. A recent survey of phosphorite deposits in the south-eastern United States included a review of the depositional and structural setting for the major areas of occurrence. The application of previous work regarding phosphorogenesis has led to the establishment of a general depositional model for most mid-Miocene primary phosphorites, and, is also possibly applicable to the Bone Valley (Pliocene-Miocene) district of central Florida.

Jan 12, 1978

By W. H. Gauvin, N. J. Themelis

Jan 1, 1963