Search Documents

By John F. Slonaker, Joseph W. Leonard

This note is a review of current research intended to increase the utilization of coal ash. Due to the magnitude of the fly-ash research program, some projects may be inadvertently omitted. Field research on fly-ash for use as an agricultural fertilizer is being monitored at Virginia Polytechnic Institute and State University. This research is directed at determining the plant nutrients that are available in fly ash as well as the quantities of fly ash that can be applied to agricultural soil.

Jan 1, 1975

By R. S. Burns, J. G. Erskine

The performance of the nine 5.5 m diameter x 6.4 m mills (18 x 21 ft) initially installed at Bougainville Copper Ltd. did not meet the laboratory and pilot plant derived design expectations as measured by Bond Work Index. During the post-commissioning period, inefficient grinding of coarse material resulted in a build-up of large circulating loads and led to reduced throughputs because of pump and cyclone overloading. Installation of larger pumps and cyclones and development of an improved circuit control philosophy alleviated materials handling problems and permitted higher tonnages to be attained. Since 1977, plant throughput has been increased by installation of three additional mills. These are 0.9 m (2.9 ft) longer than the other nine and have a higher capacity. Developments in classification and mill speed-up, together with a finer ball mill feed size and substantial improvements to mill availability (99% in 1982) have further increased plant capacity. There is a continuing emphasis on improving grinding circuit efficiency in terms of throughput/grind. Current development work includes trials of graded ball charges, different liner profiles, and assessment of scalping/regrind proposals.

Jan 1, 1985

By R. T. Hukki

BALL wear as observed in grinding installations is the combined result of mechanical wear and corrosion. Corrosion should be a linear function of the ball surface available. Ball corrosion, however, has been studied so little that its effect, although of great importance, cannot be included in the analyses given here. In a separate paper' it is shown that [ ] Exponent m is the slope of a straight line on logarithmic paper relating mill speed (on the abscissa) and mill capacity (on the ordinate).

Jan 6, 1954

By David A. Wracher

A geologist may produce for himself a surprisingly accurate photo base map and stereo coverage at low cost without the use of expensive equipment and complex photogrammetry. If care is taken and the program well thought out, good results can be expected. The only equipment necessary in this method is a small format (small negative size) camera, a few rolls of film and the appropriate filters. A light aircraft, with an opening in the bottom, is preferable so that the pictures can be taken vertically and from inside - the aircraft. The method will produce high resolution prints at large scales in the range of 1: 1200 to 1:7200.

Jan 11, 1973

By Percy Gillie

THE Tralee preparation plant, owned and operated by the Semet-Solvay division of Allied Chemical and Dye Corp., is located on the Virginian rail- way, near Mullens, Wyoming County, W. Va., and the mine, which is in the Winding Gulf district, produces coal exclusively from Pocahontas No. 3 seam. The property, comprising 4900 acres, is leased from the Pocahontas Land Corp. Prior to 1930 four separate mines were operated in this tract, some having been started about 1916.

Jan 11, 1953

By Arthur Zentner

The electrolytic zinc plant of today is foreshadowed in the patents issued to Léon Létrange of Paris in 1881 and 1883l. He proposed roasting zinc blende to make the zinc soluble in water or sulphuric acid, thus obtaining a sulphate solution. His purification was apparently that used in the lithopone work of the day. For electrolyzing he proposed anodes of carbon or lead, for cathodes zinc, copper or brass. Numerous patents by other workers were taken out in the first 10 years, most of which dealt with sulphate solutions. It is easy to presume that the formation of chlorine gas in zinc chloride electrolysis caused early emphasis on sulphate work. Lack of success with this invited further work with chloride solutions. Efficient and cheaper oxidizing agents for use in the chloride processes were more generally available. Carbon anodes could be used instead of lead anodes, which were blamed for much of the early electrolyzing troubles and remained in disfavor for many years. Carl Hoepfner received his first zinc patents in 18902. He was the most persistent of those who worked with chloride solutions and met with the largest measure of success. Hc built three plants, only one of which remained in operation. This was built in 1896 at the plant of Brunner, Mond & Co., Winnington, England, now part of Imperial Chemical Industries Ltd. It leached with by-product calcium chloride from the company's Solvay alkali plant and returned to it the chlorine formed in electrolyzing. The zinc plant had a capacity of 5 long tons of zinc, said to have been doubled later, and remained in operation until 1924. No commercial plant using chloride solutions has operated since then. E. A. Ashcroft experimented in the middle nineties with chloride, alkaline and sulphate solutions on materials from Broken Hill, Australia. He built a plant with a rated capacity of 10 long tons of zinc per day, at Cockle Creek, New South Wales, in 1898. This figure was never approached nor was cyclical operation achieved. The work in the plant appears to have been largely with sulphate solutions. The plant suffered from a multitude of troubles: poor roasting, gclatinous silica, liberal use of live steam in solutions to combat the gclatinous silica with considerable

Jan 1, 1937

By S. W. Kessler, R. B. Pond

Metal specimens were solidified through a measured thermal gradient so a free surface and the liquid-solid interface could be examined. A line structure was observed on the surface and a hexagonal structure on the interface. A model to explain these forms is proposed. NUMEROUS observations of the dendrite form have been made both in nonmetallic and metallic systems. From these, extrapolations have been made as to the probable dendrite form in pure metals. Observations of the dendrite form in pure metals, nevertheless, have been scanty. In general, these observations have been made on the skeleton dendrite after the mother liquid has been drained from around it, and a mechanism of the formation of the dendrite has been postulated from this solid form. Recent investigations have been conducted in an endeavor to make a study of the formation of the dendrite in several pure metals and the effect of several variables on this mechanism and final form. For these investigations, an apparatus was designed and constructed as shown in Fig. 1. It consists of a talc block containing a half-cylindrical depression, the end of which terminates in the conical recess of a copper block having an external attachment for cooling. A heating coil extends the length of the mold just beneath the lower limits of the cavity. The entire cavity for holding metal is coated with a thin film of graphite. Six thermocouples are equally spaced in the cavity and under the graphite, and six microammeters indicate the temperatures at the particular thermocouple stations. Readings were taken of all meters at the same instant time measurements were taken by photographing the panel of microammeters and a stop watch which was started at the beginning of the run. It was possible with this apparatus to solidify metals through a measured thermal gradient and to observe the progression of the liquid-solid interface with time by following the formation of the dendrite markings in the surface of the solid material. These

Jan 1, 1952

By William E. Ford, Edward Salisbury Dana

This section includes the common calcium titano-silicate, Tiianite; also a number of silicates which contain titanium, but whose relations are not altogether clear; further the titanate, Perovskite, and niobo-titanate, Dysanalyte, which is intermediate between Perovskite and the species Pyrochlore, Micro- lite, Koppite of the following section. In general the part played by titanium in the many silicates in which it enters is more or less uncertain. It is probably in most cases, as shown in the preceding ages, to be taken as replacing the silicon; in others however, it seems to play the part of agaaic element; in schorlomite (p. 510) it may enter) in both relations.

Jan 1, 1922

By H. L. Washburn, G. L. Judy

DURING recent years thermal drying of fine coal has increased at a tremendous rate, but very little discussion of the several excellent units has found its way into print. This is particularly true for operating and maintenance costs, and the operator who is faced with his first fine coal drying installation must depend chiefly on hearsay when trying to determine what his drying costs will be. This article presents the maintenance and operating costs for the seven drying units now installed in preparation plants of Pittsburgh Consolidation Coal Co. and lists other cost information that should be obtained before any particular drying unit is selected.

Jan 10, 1957

By Edward B. Dismukes, Walter R. Dickson

Measurements of current efficiency at an iron anode during the electrolysis of FeO-CaO-SiO2 melts contained in an iron crucible indicate that compositions of high SiO5 content conduct current almost entirely by ionic mechanisms. Hozueuer, compositions of high metal oxide content give euidence for considerable nonionic conduction that can be attributed to p-type semicon-duction. Measurements of transference numbers in a Hittorf-type cell show that both calcium and iron ions are important contributors to ionic conduction. ELECTROCHEMICAL properties such as conductance, transference numbers. and oxidation or reduction at an electrode have been studied as means of delineating the structure of simple silicate melts that are related to the more complex slags encountered ir steelmaking processes.' Measurement of these properties has strengthened the concept that molten silicates are constituted of metal ions and of silicate networks. Typically, the magnitude of electrical conductivity and the extent of agreement with Faraday's law have given evidence for ionic structures, and transference numbers have shown cations to be the exclusive carriers of electrical charge. However, melts containing oxides of iron, FeO in particular, have been found to exhibit nonionic conduction of curx,ent. The work by Inouye, Tomlinson, and chipman' demonstrated semiconduction, presumably of the p-type, in molten wüstite. Simnad, Derge, and George3 and Dukelow and Derge,4 in studying the electrolysis of FeO-SiO2 and FeO-MnO-SiO2 melts, concluded that p-type semi-conduction occurs in these systems, although ionic conduction is generally favored by increased percentages of MnO or SIO2. Previous research on the electrochemistry of

Jan 1, 1962

By A. Karim, T. G. Langdon, C. Y. Cheng, J. E. Dorn

The effect of changes in temperature and stress on the creep behavior of Fe-4 pct Si was investigated over the temperature range from 650° to 1175K Over the temperature range of 799° to 110l°K, the shear strain rate, ?', obeys the relationship: where K is a constant, 7 the applied shear stress, G the shear modulus, g the free activation energy for diflusion, R the gas constant, and T the absolute temperature. The results strongly suggest that the creep in this alloy is controlled by a dislocation climb mechanism. In a recent investigation, Ishida, Cheng, and Dorn1 observed that the apparent activation energy for creep of a! Fe from 480" to 775°K corresponded to that for self-diffusion. Over the magnetic transformation range (775" to 1045"K), the apparent activation energy for creep increased steeply with increasing temperature in agreement with the known decrease in the free activation energy for self-diffusion. Passing through the Curie temperature, the apparent activation energy decreased abruptly following which it then increased mildly as the temperature further increased. Inasmuch as the apparent activation energy for creep of a! Fe below the Curie transformation range of temperatures appeared to decrease with increasing values of the stress, the data were analyzed in terms of a model based on the nonconservative motion of jogged screw dislocations. But since the observed creep rate was much higher than that which could be accounted for on the basis of usual models, the authors found it necessary to assume that pipe diffusion became significant over the lower temperature range. Furthermore, the abnormally high activation energy for creep above the Curie temperature was attributed to grain boundary migration which became prevalent in this temperature range. It was thought that a number of the interesting issues that arose in the creep of a Fe might be resolved by investigating the creep of Fe-4 pct Si alloy: This alloy has about the same Curie range and therefore should give creep results that closely parallel those for a Fe and in this way provide comparable data for analysis of creep mechanisms. Furthermore, it can be annealed at higher temperatures which could provide some stabilization against grain boundary migration. In addition, it might serve to illustrate the possible effects of short-range ordering on creep.

Jan 1, 1969

By D. J. Bourne, G. E. Atwood

The new potash refinery of Duval Sulphur & Potash Co. produced its first tonnage of muriate of potash in November 1951. Full capacity was attained in early 1952. Excellent extraction efficiency is being obtained by the process, which is basically froth flotation. System temperature control is practiced and has proved to be of great metallurgical value through high potassium recovery and low reagent cost.

Jan 11, 1953

By A. G. Suydam

Ancient as is the art of producing copper, so ancient is one of its eternal problems: refractories. Looking backward, in the light of present knowledge, clouded though it be, one cannot avoid a sense of profound respect for the patience, acumen and courage of those who have wrought so successfully despite difficulties, a more accurate understanding of which seems merely to accentuate. The problem of refractories arises from the necessity for constructing containers in which to bring natural ores into thermal solution in order to effect reduction and separation of the valuable metal content and free it of undesirable contamination while producing a waste slag. The very forces known to produce thermal solution of sufficient liquidity are necessarily destructive of exposed refractory linings in proportions varying inversely with thermal conductivity, directly with the porosity and ease of fluxing of the refractories used, and directly with the temperatures employed. Beyond this, mechanical forces are set up within the refractory lining incident to rapid heating or cooling, shrinkage at high temperatures, and unequal or excessive loading, that frequently pass the elastic limit, causing spalling or distortion. The effects of these forces are often accentuated by the necessity of providing at the same time as hot a bath and as cool a container as are consistent with fuel economy. Evolution in the Use of Refractories Clay Brick.—Fireclay and clay refractories had to yield wherever they were in contact with slags rich in basic oxides, first because of the combining power of those oxides with free silica and secondly because of the tendency of alumina to form either aluminates or alumina-silicates of varying complexity. Of no less importance, the incipient fusion point was low as compared with good clay brick of today, while the brick lacked strength at high temperatures. Expansion was slight, therefore it was difficult to make and maintain tight walls, roof, or bottom. However, the spalling tendency was low because of some of these properties and clay brick have retained their place in roasting furnaces, boiler furnace linings, and in the upper walls of some of the reverberatory types such as some refining, anode and wire-bar furnaces. They have served often and most efficiently for hot patching.

Jan 1, 1934

By Raymond E. Zimmerman

The Swirl Cyclone developed in Japan, although based upon the same principles as the standard cyclones for heavy-media or water-only cyclones for cleaning coal, is novel in that it is invested with the apex on top, discharging rejects at the top, and clean coal at the bottom. It also uses a variable air vent tube for controlling the vortex. Tests conducted indicate that its efficiency is not only as sharp as standard cyclones but it also performs using a much coarser grain magnetite, promising higher magnetite recovery. The author describes the results of tests conducted in Japan on a very difficult coal.

Jan 1, 1979

By Horace V. Winchell

The St. Helens mining-district, indicated in sketch-map, Fig. 1, is chiefly in Townships 9 and 10 North, Ranges 5 and 6 East of the Willamette meridian, in Skamania county, Wash. There is no railroad or even a wagon-road at present connecting it with any base of supplies; access is usually by wagon-road for about 50 miles from the town of Castle Rock to Spirit lake, and from that point by pony-trail from 6 to 10 miles farther. History. Nearly 20 years ago two German farmers, totally inexperienced in prospecting, penetrated this region upon a hunting-and fishing-trip. Their attention was drawn to numerous joints and crevices filled with black, glistening tourmaline, and con-

Jan 1, 1913

By E. W. Krampert

The oil industry was very active in Wyoming in 1936, in contrast to the several quiet years preceding. Production for the year again increased about 7 per cent, following an 8 per cent increase in 1935. During the year, 85 oil wells were completed, compared to 55 in 1935. Three gas wells were completed in 1936, and three in 1935. At the end of the year 45 wells were drilling, as compared to 55 drilling at the end of 1935. Two new oil fields and one new gas field were discovered in Wyoming during the year. In the year 1936 Wyoming produced 14,475,431 bbl. of oil, a gain of 1,001,081 bbl. over the 1935 figure of 13,474,350. This increase, in the main, was due to the taking of light oil from the newly developed Sundance sand pool at Lance Creek, and from the new fields, Quealy and Medicine Bow, which contributed their first production this year. Most of the other old fields either were partly shut in in competition with the new fields, or showed a normal decline. This was especially noticeable in the black-oil fields, where production had been slowly but steadily increasing for a number of years. During 1936 black-oil production decreased approximately 100,000 bbl. as compared to 1935. The only black-oil field to show marked increase was Garland, which managed to take the market from less favorably located fields. The production of Wyoming in 1936 was 11,358,757 bbl. of light oil and 3,116,674 bbl. of black oil. Salt Creek, with a production of 6,015,000 bbl., is still the largest single oil-producing field, accounting for 42 per cent of the year's total production. Lance Creek, an old field, with newly developed production in the Sundance sand, reached second place this year for the first time in its history, with a production of 1,878,486 bbl. Lance Creek production will almost equal that of Salt Creek in 1937, if the present rate of production is maintained during the coming year. Oregon Basin, a large black-oil field, held second place in 1935, but owing to a greatly lessened demand for its production, dropped back to third place in 1936. This was in part due to greatly increased light oil available, and in part to the greater supply of black oil available at

Jan 1, 1937

By James Yancik

The Howe Coal Co. is mining the Oklahoma Lower Hartshorne bed which ranges in seam thickness from 38 to 42 in. and pitches approximately 7° to the northeast. The raw feed to the cleaning plant averages about 20% ash and 1.10% sulfur, being reduced in the cleaning process to 4.8% ash and 0.9% sulfur with a free swelling index of 8 or 8%. This coal rivals the Pocohantas seam in chemistry and coking characteristics but has better fluidity than the Pocohantas seam coal. The coal is presently being prepared for the Japanese steel market in an 85-tph pilot plant designed and constructed by Roberts & Schaefer. The cleaning-plant flowsheet is discussed in detail.

Jan 1, 1972

By Olev Trass

The mill body is a stationary grinding cylinder inside which a number of helically grooved rollers rotate, each being suspended on a flexible axis. The feed material is repeatedly crushed between these rotors and the cylinder, with the crushing force created by radial acceleration. The mill has several internal design variables such as number, size and shape of rotors, and can be operated wet or dry. It is compact, has a high capacity, modest power consumption, and can grind many materials down to ultrafine powder. Illustrative data on product size distributions and particle shapes are given for grains, metals and minerals obtained at various operating conditions, along with initial results on grinding kinetics.

Jan 1, 1980

By H. T. Wyatt, A. S. Baptie

The Ten Section field is approximately 10 miles southwest of Bakers-field, Kern County, Calif. (Fig. 1). There is no surface evidence of the existence of the Ten Section structure, which subsurface exploration has shown to be a gently folded, anticlinal dome. Regionally, this field occurs as a fold in the deeper beds of the gently rolling floor of the San Joaquin Valley. It is on the easterly slope of the valley, its position with relation to the axis of this syncline not having been determined. The field was discovered by Shell Oil Co. with the completion of well Stevens A-l, on June 2, 1936, at a depth of 7888 ft. The location for this

Jan 1, 1938

By W. I. Garms, J. L. Stevens

Because of the many conflicting opinions regarding the functioning of the ball load and the characteristics of ball wear in ball-mill grinding, the following résumé of reports covering recent tests conducted at the Hayden plant of the Kennecott Copper Corporation is submitted with the view of pointing out certain salient features that should throw additional light on the subject. Mills Used Cylindrical drum mills with trunnion feed and discharge were used. The discharge trunnion was 13½ in. in diameter. Dimensions inside the lining were 6 ft. 6 in. in diameter and 9 ft. 6 in. long. The mills were Britannia-lined and nine lifter bars projected 2 in. from the lining. The mill speed was 162/3 r.p.m. Feed to the mill was 9 per cent on 10-mesh, 85 per cent on 100-mesh, 77 per cent solids. New balls measured 2 in. in diameter and the approximate weight of the ball load was 40,000 pounds. Initial Test During a test that was being conducted to determine the relative economic value of standard cast balls vs. forged steel balls in the local 'grinding operation, certain observations were made in regard to the functioning of the various ball sizes and the characteristics of ball wear, which warranted a supplementary test for the purpose of confirming such observations. For the initial test, the necessity for developing a graduated load of the new forged balls before the test could be started was realized, but the time required to obtain a graduated load and the functioning of the various ball sizes was not clear. No advantage could be seen for starting out with a full load of forged balls, as this initial load, at the least, would have to be completely ground out and replaced by daily additions of balls before the graduation could be complete and a normal static condition of ball sizes reached. For a considerable period prior to exhaustion of this initial charge there would be an unusual quantity of worn balls of a certain size, which would not be typical of a normal charge and could influence the characteristics and functioning of the entire load. Therefore, it was decided to start by daily addition of the forged balls to a mill that contained a normal operating load of cast balls. After 88 days of operation the mill was shut down for inspection. By that time the load consisted of a mass of forged balls functioning around a large core of the residual material of the former cast-ball load. This core of cast slugs, locally referred to as "the kidney," was well defined from the forged-ball load.

Jan 1, 1947