Search Documents

By B. W. Gandrud, R. G. Meara, O&apos

In 1034 the Southern Experiment Station of the U.S. Bureau of Mines in cooperation with the University of Alabama began an investigation of the availability of kyanite ores as a source of raw material for the manufacture of refractories. Under this program, gravity concentration and flotation tests have been made on two varieties of Georgia kyariite ore, mica schist and massive. Most of the attention has been directed to the mica schist ores, as they are more widely distributed and seem to offer greater economic possibilities than the massive ores. It is evident that the preparation of kyanite for use as a refractory material involves other considerations than the mere elimination of impurities. A concentration process that eliminates impurities satisfactorily may have to be followed by some additional treatment, since the final product must be of a coarseness and size ratio that will make it suitable for refractories manufacture. So far in the investigation at the Southern Experiment Station of the U.S. Bureau of Mines only the concentration problem has been considered, and this paper is intended as an interim report. Ores The schist ores contain 1 to 9 per cent of kyanite crystals embedded in mica and quartz, with smaller amounts of graphite, garnet and iron oxide and minor amounts of other heavy minerals. The garnet content varies from a trace to a few per cent. The minerals are easily released by moderate grinding. The size of the kyanite ranges from fine needles to crystals 1 1/2 in. long, 1/2 in. wide and 1/4 in. thick. The garnet, quartz and iron oxide grains have a smaller mean mesh than most of the kyanite. The maximum size of the garnet crystals corresponds to about 14 mesh and that of the sand grains is considerably less. Most of the iron oxide is still finer, for the minus 100-mesh size is greatly enriched in Fe²O3. The massive ore consists of radiating masses of kyanite interlocked with quartz, mica, corundum and small amounts of other heavy minerals.

Jan 1, 1938

By E. W. Schilling

THE-separation of hematite by hysteretic repulsion was first brought to the attention of the public in 1922, by W. M. Mordey1. Three-years later another paper2 was published and after another four years a third paper3 appeared in the South African publications. Certain data were lacking in these papers. In order to continue the work intelligently a knowledge of the shapes of the hysteresis curves for certain minerals was very necessary. This information was not available until the present year4. It was known that reduction of certain ores rendered them amenable to this process of separation but definite data in. the form of curves showing exactly the effect of such treatment were lacking. Prob-ably our best source of information on the separation of minerals by the use of alternating-current magnetic fields today is the reports from the U. S. Bureau of Mines 5-7. It is not the purpose of this paper to tell the reader in detail how to make a commercial separator. Experimental models have recently been made7 and the results obtained have been so good that it is the opinion of the authors that the public will soon take an active interest in the subject and its development. The writers have constructed a separator that is considerably different in construction and operation from the two types described by Mr. Davis. This will be described; but the real purpose of this paper is to outline certain experiments and give curves showing data that have a fundamental bearing upon the practical construction of a separator of this type.

Jan 1, 1936

By A. B. Kinzel

Since the exposition of the behavior of certain iron alloys by Sykesl involving the existence of an austenite loop and the discovery of such a loop in the chrome-iron system by Bain,2 there has been much conjecture both on his part and on the part of metallurgists in general as to the exact shape and location of this loop. In previous work commercial steel has been used and the microscope has been employed to locate the critical points so that the position of the loop has been quite approximate. Numerous attempts have been made to measure the critical points of the carbon-free alloys but all of these for one reason or another have failed. A satisfactory method for studying these phenomena is presented here. MateRial The first difficulty in this study was to obtain pure chromium-iron alloys. This has been overcome by melting in a vacuum electrolytic iron and chromium analyzing 99.84 Cr, Fe and C. A pure magnesite crucible was used and the melt allowed to solidify in the crucible. A typical analysis is chromium, 10.10 per cent., carbon, 0.006 per cent., silicon and manganese nil. To overcome the problem presented by segregation, ingots were made into wire 0.04 in. in diameter. This was accomplished by hand-forging the ingots into rods, using an oxyhydrogen flame for heating, in order to avoid carbon. Subsequently the rods were swaged to wire, the heating being carried out in hydrogen. Thus local segregation was eliminated although differences in analysis between portions 50 ft. apart were noted. An electric-resistance method was first tried to determine the critical points, but due to the physical defects in the wire this failed. Bain had previously shown the presence or absence of critical points in a qualitative way by observing the sag in a catenary. The author has devised the following method which gives an accurate determination of the critical points from expansion-temperature curves of suspended wire, a special telescopic dilatometer being used for the purpose.

By D. T. Jones

In view of the importance of the application of scientific principles to the production of oil from the reservoir, the Production Staff of the Anglo-Iranian Oil Co. (late Anglo-Persian Oil Co.) has been engaged for some years on an intensive program of research on the physical properties of crude oil. Problems involving the retention of crude oil in capillaries and fine fissures demanded for their solution a knowledge of the surface tension and specific gravity of the crude under reservoir conditions, and it is the purpose of this paper to describe briefly the methods adopted for the determination of these properties, and to present the more important results. A detailed article was published in volume 1 of the World Congress Proceedings (1933). Surface-tension observations on crude oil regassed at high pressures with natural gases have been made in the past by Beecher and Park-hurstl and Swartz2, but up to the time of the investigations in Iran no one seems to have carried out experiments with gas-saturated crude direct from the reservoir and kept at its original pressure. Results obtained in this manner are obviously of greater practical value for solving problems connected with the reservoir. Method of Measurement No apparatus for the measurements, under the pressure conditions involved, was available, and a suitable instrument had to be designed and constructed in the Fields workshops. Careful consideration of the matter led to the adoption of a method for measuring the surface tension which did not involve a knowledge of the specific gravity of the oils under the working conditions: the main reason for this being that up to that time no accurate determination of the specific gravity had been made under these conditions. The method adopted involves the measurement of the actual tension in an oil film, and is effected by means of

Jan 1, 1936

By D. T. Jones

In view of the importance of the application of scientific principles to the production of oil from the reservoir, the Production Staff of the Anglo-Iranian Oil Co. (late Anglo-Persian Oil Co.) has been engaged for some years on an intensive program of research on the physical properties of crude oil. Problems involving the retention of crude oil in capillaries and fine fissures demanded for their solution a knowledge of the surface tension and specific gravity of the crude under reservoir conditions, and it is the purpose of this paper to describe briefly the methods adopted for the determination of these properties, and to present the more important results. A detailed article was published in volume 1 of the World Congress Proceedings (1933). Surface-tension observations on crude oil regassed at high pressures with natural gases have been made in the past by Beecher and Park-hurstl and Swartz2, but up to the time of the investigations in Iran no one seems to have carried out experiments with gas-saturated crude direct from the reservoir and kept at its original pressure. Results obtained in this manner are obviously of greater practical value for solving problems connected with the reservoir. Method of Measurement No apparatus for the measurements, under the pressure conditions involved, was available, and a suitable instrument had to be designed and constructed in the Fields workshops. Careful consideration of the matter led to the adoption of a method for measuring the surface tension which did not involve a knowledge of the specific gravity of the oils under the working conditions: the main reason for this being that up to that time no accurate determination of the specific gravity had been made under these conditions. The method adopted involves the measurement of the actual tension in an oil film, and is effected by means of

Jan 1, 1936

By R. Grierson, R. N. Parkins

The m.echanica1 properties, at high lzomologous temperatures, of the intermetallic compounds InzBi and Mg17A112 were measured as a .function of temperature, applied strain rate, previous thermal and mechanical history, and composition. Mgl,Al12 was investigated ilz compression, whereas Zn,Bi was investigated in tension. A decrease inflow stress with increasing strain was observed jor both alloys. The results obtained are discussed in terms of the dislocation-multiplication processes in these materials. MANY intermetallic compounds are reported to undergo a brittle-ductile transition at high homologous temperatures.' There is evidence in the literature that some of these compounds exhibit a large yield drop when plastically deformed.'j3 Both of these forms of behavior are shown by the covalent elements germanium and silicon4,5 and also by certain ionic compounds.8 The present work is a study of the deformation, at high homologous temperatures (>2/3 Tm), of two intermetallic compounds, In2Bi and Mg17Al12. InzBi has a disordered hexagonal structure7 (c/a = 0.598) and a solubility range of 32.3 — 33.2 at. pct Bi.8 It has a melting range from 72° to 89°C. Mg17Al12 has an ordered bcc (A12 type)7 structure and exists over the range 50 to 60 at. pct Mg8 with a melting range from 437° to 462°C. We have been unable to find any reference to previous investigations of the mechanical properties of BiIn,. Novikovg has reported that cast samples of Mg17A112 show ductility, when bend-tested, at temperatures above 380°C. EXPERIMENTAL Ingots of In2Bi and Mg17Al12 were melted under an argon atmosphere and cast, in situ, in a graphite crucible. The materials used were of 99.99 pct purity. The alloys prepared contained 66.9 at. pct In in the case of In2Bi and 58.4 at. pct Mg in the case of m17A112. The ingots were homogenized and then extruded. Two-in.-diam Mg17Al12 ingots were extruded at 375°C to give 3/8-in.-diam rod. The rate of formation of this rod was 0.25 in. per min. One-in.-diam InzBi ingots were extruded at 20°C, using a rate of 1 in. per min, to give 1/8-in.-diam rod. In both cases the extruded rod had a recrystal- lized, fine-grain, structure. (For Mg17Al12, d = 11.2 µ; for BiIn2, d = 22 µ.) Mechanical-property determinations were made in a hard-beam machine, in tension in the case of In2Bi and in compression with Mgl7Al12. The tensile tests were on specimens having a gage length of 1.1/2 in. and a diameter of 1/8 in. The compression tests on Ml7A112 were on specimens of 3/8 in. diam by 3/8 in. high and the ends were coated with poly-tetrafluorethylene to minimize friction. RESULTS In2Bi. Fig. 1 shows, particularly at the higher applied strain rates, that In2Bi exhibits a marked yield drop as the deformation increases to about 2 pct, after which the material shows neither hardening nor softening up to 15 pct strain. The magnitude of the yield drop, the stress in the region of flow under constant stress (the stress plateau), and the 0.5 pct proof stress were all dependent upon the applied strain rate according to an expression of the form

Jan 1, 1965

By O. C. Wheeler

The total oil production from Colombia during 1939 amounted to 23,774,151 bbl., constituting a new high record. Of this amount the Tropical Oil Co. produced 22,374,151 bbl. from its De Mares concession and the Colombian Petroleum Co. produced 1,400,000 bbl. from its Barco concession beyond the eastern Andes. The Socony Vacuum Oil Co. produced a small amount of crude from its Las Monas wells north of the Sogamoso River in the Magdalena Valley for consumption on its own property, but this is not included in the figures given above. The South American Gulf Oil Co. provided the outstanding development in the country by the completion, late in the year, of its 12-in. pipe line from the Colombian Petroleum Company's Barco concession to the coast at Covenas. This was a notable accomplishment, achieved in the face of tremendous natural obstacles. With the completion of this line there are now two crude-oil outlets from the interior of Colombia to the coast, the other being the Andian National Corporation's line down the Magdalena Valley from Barranca Bermeja. The Barco property becomes the second major producing area in Colombia. The acquisition of prospectivc oil lands continued at about the same level as during the prcvious year. Most of the lands taken up or applied for had their subsurface rights vested in the National Government. Relatively little interest was taken in the leasing of privately owned lands. Tropical surrendered its Putana concession on the Sogamoso River after finding it to he nonproductive. The status of applications for National lands that had been accepbed or on which concession contracts had been awarded at the end of the year is shown in Table 3. In the Magdalena Valley wildcat drilling in the search of new fields was conducted to the east of Puerto Berrio by the Compania de Petroleo Shell de Colombia, Compania Coloinbiaila de Petroleos El Condor and by the Sociedad Nacional del Carare; further down the valley to the cast of Puerto Wilches, the Socony T'acuum was drilling two wildcats. No discoveries resulted from this exploratory work. On the Barco conces-

Jan 1, 1940

By O. C. Wheeler

The total oil production from Colombia during 1939 amounted to 23,774,151 bbl., constituting a new high record. Of this amount the Tropical Oil Co. produced 22,374,151 bbl. from its De Mares concession and the Colombian Petroleum Co. produced 1,400,000 bbl. from its Barco concession beyond the eastern Andes. The Socony Vacuum Oil Co. produced a small amount of crude from its Las Monas wells north of the Sogamoso River in the Magdalena Valley for consumption on its own property, but this is not included in the figures given above. The South American Gulf Oil Co. provided the outstanding development in the country by the completion, late in the year, of its 12-in. pipe line from the Colombian Petroleum Company's Barco concession to the coast at Covenas. This was a notable accomplishment, achieved in the face of tremendous natural obstacles. With the completion of this line there are now two crude-oil outlets from the interior of Colombia to the coast, the other being the Andian National Corporation's line down the Magdalena Valley from Barranca Bermeja. The Barco property becomes the second major producing area in Colombia. The acquisition of prospectivc oil lands continued at about the same level as during the prcvious year. Most of the lands taken up or applied for had their subsurface rights vested in the National Government. Relatively little interest was taken in the leasing of privately owned lands. Tropical surrendered its Putana concession on the Sogamoso River after finding it to he nonproductive. The status of applications for National lands that had been accepbed or on which concession contracts had been awarded at the end of the year is shown in Table 3. In the Magdalena Valley wildcat drilling in the search of new fields was conducted to the east of Puerto Berrio by the Compania de Petroleo Shell de Colombia, Compania Coloinbiaila de Petroleos El Condor and by the Sociedad Nacional del Carare; further down the valley to the cast of Puerto Wilches, the Socony T'acuum was drilling two wildcats. No discoveries resulted from this exploratory work. On the Barco conces-

Jan 1, 1940

By H. A. Wentworth

THE Huff electrostatic plant of the United States Smelting Company operated in conjunction with its wet concentrator at Midvale, Utah, was the second plant of substantial size installed using the Huff process, and the first plant to be put in operation on the so-called Western complex ores. In spite of the machinery being of early design and consequently embracing many of the mechanical weaknesses incident to a pioneer plant the mill has operated steadily and uniformly since the summer of 1909, about five years now, without any material change other than some re-arrangement of the machinery for better handling of the sizes. The ore, at present coming almost entirely. from the company's mines in Bingham, is of practically the same composition as that upon which the plant was first put in operation. The crude ore, consisting of the sulphides of copper, lead, zinc, and iron, and containing small amounts of gold and silver, is brought by train and delivered to the hoppers of the wet concentrator, where by jig and table treatment, there are produced a shipping lead concentrate, a tailing and a middling product, the latter being conveyed in push cars to the adjoining electrostatic mill. The crude ore delivered to the wet concentrator contains from 6 to 9.5 per cent. zinc. At times the plant is used also for the treatment of custom ores from the Bingham district and elsewhere, and at such times the results of the plant vary according to the material in use, but as by far the larger portion of the product is that from the company's own mines, the results given below are fairly indicative of the general work obtained. The accompanying diagram illustrates graphically the flow of the ore through the electrostatic mill. The middling coming from the wet mill containing from 15 to 18 per cent. moisture is hoisted while on the cars by an elevator, and delivered from the top of the elevator to a hopper over the drier. The drier first installed was of too low capacity to take care of the moisture present in the tonnage to which the mill was later

Jan 8, 1914

By H. W. Camp

Although the situation in the oil industry during the past year has not been conducive to large expenditures for development and research, there is little indication that such expenditures have been curtailed. While few outstanding achievements have been reported, considerable progress has been made in the development of new product,s and the adaptation of petroleum derivatives to new uses. The most important question facing the refiner today is the antiknock quality of his gasoline. This year has seen the widespread adoption of the term "octane number" as a measure for anti-knock values, and in the latter months of the year the public has been made acutely aware of this condition through competitive advertising. Gasoline is no longer priced on volatility and gravity alone, but on octane number as well; and premiums are being paid for material of relatively high octane rating. The situation has grown more and more competitive and has forced refiners continually to raise the octane rating of their regular and competitive grades, and at this writing the same situation exists for premium grades which have possessed relatively high anti-knock properties for some time. Straight-run gasoline produced from paraffin-base or semiparaffin-base crudes has an inherently low anti-knock value, and in order to convert this material to a higher quality it has been found necessary to crack an increasing percentage of the crude oil charge. By completely cracking the heavier portions of the crude and blending back with the straight-run gasoline, it has been possible to produce an average of 63 to 65 octane number gasoline on average Mid-Continent crude. This operation carried to the fullest extent does not suffice, however, and the recent and rapid development of the so-called '(reforming unit," has resulted. The straight-run gasoline fraction is cut into two parts: a light, low boiling point gasoline; and a heavy gasoline or naphtha. The latter containing the low anti-knock portions of the gasoline, is sent through a re-forming unit and subjected either to high temperature or pressure, or both, which materially increases its octane number. On average Mid-Continent the blend of low boiling point straight-run,

Jan 1, 1932

By AIME AIME

EUGENE AUSTIN STEPHENSON, better and affectionately known as "Steve," has long been an active and enthusiastic member of the Petroleum Division of the Institute. As its Secretary-Treasurer for several years, he was the spark plug that so successfully carried the Division over the trying period of the early thirties. "Steve" was born at Franklin, Mich., July 27, 1883; graduated from Adrian College in 1905, and later received his Doctor's degree from the University of Chicago where he was an instructor for two years. From 1917 to 1925 he was chief geologist for the South Penn Oil Co. and from 1925 to 1930 he was associated with Ralph Davis, Inc., of Pittsburgh, consulting engineers. In 1930 the Missouri School of Mines called him to Rolla to head a department of petroleum and natural gas engineering. and in 1938 he was invited to build up a similar department at the University of Kansas.

Jan 1, 1941

By L. H Levenson, Charles S. Barrett

The orientation of metal crystals and grains, both large and small, can be detcrmined conveniently and accurately without the use of X-ray apparatus. This seems to be appreciated by so few metallurgists that it may be useful to explain in detail the method we have found most satisfactory in the laboratory—the reflection of light from crystallographie etch pits. This note includes a description of a suitable inexpensive instrument and instructions for etching various metals and for plotting the data. As the stereographie projection is used to facilitate handling the data, this note may he considered as an appendix to an earlier review of the metallurgical uses of the stercographie projection.' Various methods involving etch pits have been used by other investigators. Bridgman's method2 consists of attaching the specimen to a sphere (a transparent sphere is convenient4 , holding it at arm's length, and marking a spot on it when it has been turned so that the eteh pits reflect light into the eye of the observer from a lamp standing behind him. It has an accuracy of about 2" and is extrernely rapid. A greater accuracy can be obtained by having the reflected light fall on a screen, as has been done by Czochralski,5 Chalmers,6 and Schubnikov.7 All of these methods have been intended for undeformed single crystals. Tammann and his coworkers3,8 developed a method for estimating the number of grains in a polyerystalline aggregate having orientations in a given region of the stereographic triangle and thus obtained statistical information about deformation and reerystallization textures. While the method has had some use in recent years,9 it is not applicable to the majority of problems in physical metallurgy. Smith and Mehl10 determined orientations by plotting the directions of the sides of individual etch pits on a stereographic projection. The accuracy is limited to about 3" and the method requires careful polishing and high magnification.

Jan 1, 1940

By Charles S. Barrett, L. H. Levenson

The orientation of metal crystals and grains, both large and small, can be detcrmined conveniently and accurately without the use of X-ray apparatus. This seems to be appreciated by so few metallurgists that it may be useful to explain in detail the method we have found most satisfactory in the laboratory—the reflection of light from crystallographie etch pits. This note includes a description of a suitable inexpensive instrument and instructions for etching various metals and for plotting the data. As the stereographie projection is used to facilitate handling the data, this note may he considered as an appendix to an earlier review of the metallurgical uses of the stercographie projection.' Various methods involving etch pits have been used by other investigators. Bridgman's method2 consists of attaching the specimen to a sphere (a transparent sphere is convenient4 , holding it at arm's length, and marking a spot on it when it has been turned so that the eteh pits reflect light into the eye of the observer from a lamp standing behind him. It has an accuracy of about 2" and is extrernely rapid. A greater accuracy can be obtained by having the reflected light fall on a screen, as has been done by Czochralski,5 Chalmers,6 and Schubnikov.7 All of these methods have been intended for undeformed single crystals. Tammann and his coworkers3,8 developed a method for estimating the number of grains in a polyerystalline aggregate having orientations in a given region of the stereographic triangle and thus obtained statistical information about deformation and reerystallization textures. While the method has had some use in recent years,9 it is not applicable to the majority of problems in physical metallurgy. Smith and Mehl10 determined orientations by plotting the directions of the sides of individual etch pits on a stereographic projection. The accuracy is limited to about 3" and the method requires careful polishing and high magnification.

Jan 1, 1940

By William G. Krantz

The increased service demands on some of the products of the National Mallcable Castings Co. prompted it about eight years ago to investigate the electric furnace, both in America and in Europe. The process had already been sufficiently developed in Europe to lead us to believe that the electric furnace would most nearly meet our requirements. After further investigation and consultation with the highest authorities on the subject, we decided upon the Heroult type as the simplest and most practicable. In 1910, we built a furnace of this type, of 300 Ib. capacity, for experimental purposes, and although it was crudely constructed the quality of the material we were able to make justified the installation of a 6-ton Heroult furnace in 1912. This furnace has three electrodes, 17 in. in diameter, uses three-phase, 60-cycle current, and is equipped with Thury regulators, which give US good regulation and a uniform load on the line even when cold melting. The power factor of the furnace is 04 per cent. Since July, 1912, the furnace has been in continuous operation, producing up to the present time over 20,000 tons of both carbon and alloy steels of varying analyses and of exceptional quality. Both cold-and hot-metal charges have been used, with a power consumption of about 150 kw-hr. per ton in the case of hot-metal charges and from 500 to 600 kw-hr. per ton in the case of cold charges. The electric energy consumed varies according to the final analysis of the steel and the amount of refining required. Too much cannot be said about the refining possibilities of the electric furnace, for no other method of steel manufacture can compete with the electric in this respect. In proper operation lies the whole secret of success. That steel has been made electrically means nothing, for when the furnace is operated under oxidizing conditions the quality is no better than that of open-hearth material; but when properly made, electric steel is as good as

Jan 1, 1916

By W. N. Tanner

The wire-rope hoisting conditions at the mines of the Anaconda Coppcr Mining Co. in Butte, Mont, are very severe because of the conditions under which it is necessary to operate. A study was made, in the fall of 1919, for the purpose of changing these conditions in order to obtain longer rope and sheave life. There are at present in Butte hoisting engines equipped with wire rope as follows: 9 main hoists using flat ropes. 7 main hoists using 1 1/2-in. rope. 5 main hoists using 11/4-in. rope. 6 shafts using 11/8-in. rope. 2 chippy hoists using 11/4-in. rope. 9 chippy hoists using 11/8-in. rope. 15 shafts using 1-in. rope. 7 shafts using 7/8-in. rope. 1 shaft using 3/4-in. rope. In addition, there are a number of sinking engines wing 5/8-in, 3/4-in., 7/8-in., and 1-in. (15.9, 10, 22, and 25 mm) rope. THe flat ropes run from 1/2 by 71/2 in. (12.7 by 1905 mm.) to-3/8 by 4 1/2-in (9.5 by 114 mm.) and are used on the older hoisting engines, which arc set comparatively close to the shaft. Because of swelling and moving ground at some of the shafts, these ropes present certain difficulties ill operation that are more pronounced than with round ropes; they are, therefore, being superseded by round ropes as newer engines are being installed. They are, however, much more easily inspected and repaired than round ropes. In general, the practice in Butte is to use hoisting engines equipped with 12-ft. (3 7 m.) cast-iron drums, smooth faced, for 11/2-in. rope and 6-ft. cast-iron drums, smooth faced, lagged with 3/8-in. steel plate for 11/4 l1/8 and 1-in. (31.7, 28.6, 25 mm.) rope in main and chippy shafts. Cast-iron head sheaves, 12, 10, and 6 ft. in diameter, with grooves

Jan 1, 1923

By L. L. Wyman

The resultant embrittlement caused by the exposure of oxygen-bearing copper when hot and exposed to reducing gases has been the subject of many studies.' Little attention, however, has been given to the possible embrittling effects due to atmospheres or conditions that under some circumstances might be the source of a reducing gas. At rather infrequent intervals there occur reports of copper becoming embrittled during normal annealing cycles in commercial steam-atmos-phered furnaces such as customarily are used for this operation. As might be expected, several other factors exist—such as oil, dirt on the wire, or in the furnace, or metallic surface contacts—that might produce reducing gases and be the source of the trouble. However, in consideration of the statement made by Ruder,2 it would seem that under some conditions steam itself might prove to be the source of trouble. A consideration of the amount of the dissociation of water vapor up to temperatures of the melting point of copper shows that3 the amount of hydrogen that could come from this source is far too minute to account for any embrittlement. What such information does not tell is what will happen at the surface of copper when subjected to steam at elevated temperatures, for entirely different conditions may persist, which would account for Ruder's observation. Furthermore, there are no data as to what might happen at the surfaces of other materials present, the resultant of which might affect the condition of the copper present. For this reason, it was decided to make a series of experiments comparable to those previously conducted by the writer,' which would clarify the effect of the steam on copper, and in copper in the presence of steel. Material The material used in these experiments was tough-pitch copper wire of rectangular cross section, about % in. thick, picked at random from the regular factory production of material used for windings, etc., in the electrical industry. Chemical analysis of this material gave the follow-

Jan 1, 1940

By W. N. Tanner

The wire-rope hoisting conditions at the mines of the Anaconda Coppcr Mining Co. in Butte, Mont, are very severe because of the conditions under which it is necessary to operate. A study was made, in the fall of 1919, for the purpose of changing these conditions in order to obtain longer rope and sheave life. There are at present in Butte hoisting engines equipped with wire rope as follows: 9 main hoists using flat ropes. 7 main hoists using 1 1/2-in. rope. 5 main hoists using 11/4-in. rope. 6 shafts using 11/8-in. rope. 2 chippy hoists using 11/4-in. rope. 9 chippy hoists using 11/8-in. rope. 15 shafts using 1-in. rope. 7 shafts using 7/8-in. rope. 1 shaft using 3/4-in. rope. In addition, there are a number of sinking engines wing 5/8-in, 3/4-in., 7/8-in., and 1-in. (15.9, 10, 22, and 25 mm) rope. THe flat ropes run from 1/2 by 71/2 in. (12.7 by 1905 mm.) to-3/8 by 4 1/2-in (9.5 by 114 mm.) and are used on the older hoisting engines, which arc set comparatively close to the shaft. Because of swelling and moving ground at some of the shafts, these ropes present certain difficulties ill operation that are more pronounced than with round ropes; they are, therefore, being superseded by round ropes as newer engines are being installed. They are, however, much more easily inspected and repaired than round ropes. In general, the practice in Butte is to use hoisting engines equipped with 12-ft. (3 7 m.) cast-iron drums, smooth faced, for 11/2-in. rope and 6-ft. cast-iron drums, smooth faced, lagged with 3/8-in. steel plate for 11/4 l1/8 and 1-in. (31.7, 28.6, 25 mm.) rope in main and chippy shafts. Cast-iron head sheaves, 12, 10, and 6 ft. in diameter, with grooves

Jan 1, 1923

By L. L. Wyman

The resultant embrittlement caused by the exposure of oxygen-bearing copper when hot and exposed to reducing gases has been the subject of many studies.' Little attention, however, has been given to the possible embrittling effects due to atmospheres or conditions that under some circumstances might be the source of a reducing gas. At rather infrequent intervals there occur reports of copper becoming embrittled during normal annealing cycles in commercial steam-atmos-phered furnaces such as customarily are used for this operation. As might be expected, several other factors exist—such as oil, dirt on the wire, or in the furnace, or metallic surface contacts—that might produce reducing gases and be the source of the trouble. However, in consideration of the statement made by Ruder,2 it would seem that under some conditions steam itself might prove to be the source of trouble. A consideration of the amount of the dissociation of water vapor up to temperatures of the melting point of copper shows that3 the amount of hydrogen that could come from this source is far too minute to account for any embrittlement. What such information does not tell is what will happen at the surface of copper when subjected to steam at elevated temperatures, for entirely different conditions may persist, which would account for Ruder's observation. Furthermore, there are no data as to what might happen at the surfaces of other materials present, the resultant of which might affect the condition of the copper present. For this reason, it was decided to make a series of experiments comparable to those previously conducted by the writer,' which would clarify the effect of the steam on copper, and in copper in the presence of steel. Material The material used in these experiments was tough-pitch copper wire of rectangular cross section, about % in. thick, picked at random from the regular factory production of material used for windings, etc., in the electrical industry. Chemical analysis of this material gave the follow-

Jan 1, 1940

By Eric Jette

IN thermodynamic studies of gas mixtures and liquid solutions, the respective problems have been greatly simplified by the use of two general limiting laws; Dalton's law of partial pressures and Raoult's law. It is generally recognized that these two laws have a common physical and chemical basis which may be stated as follows: The law may be expected to be strictly valid only for systems in which the different molecular species are so nearly the same in their physical and chemical properties that a molecule is unable to recognize whether its neighbor is one of its own kind or not. Positive and negative deviations from both laws are frequently encountered. The occurrence of negative deviations in both gases and liquids is ascribed to attractive forces which, in the more extreme cases, may be so large in magnitude and so highly specific in character as to lead to the formation of definite chemical compounds. Positive deviations in gases develop only at higher pressures where the intermolecular distances are so decreased that factors such as molecular size and shape, which ultimately become concerned with the repulsive forces, come into play. In liquid mixtures, positive deviations are generally considered as due to differences in the symmetrical (nonpolar) fields of force which surround the various molecular species and which are supposed to give rise to a tendency for each species to associate with its own kind and thus to "squeeze out" the other variety. Fundamentally this also involves the existence of repulsive forces between unlike molecules. If the fields of force are unsymmetrical (polar) a tendency towards compound formation results. Stated in more exact terms, strict adherence to the law means that the "activity" (or any adequate measure of this quantity) of a component in a mixture is a linear function of the molecular (or atomic)

Jan 1, 1934

By Frederick J. McGarry, Fred Moavenzadeh

An experimental investigation of the thermal and mechanical responses of rock materials to laser radiation is described. Specifically, the following three topics have been studied in detail: 1. Temperature measurements on thin discs subjected to laser radiation. 2. Strain measurements on thin discs subjected to laser radiation. 3. Observation and evaluation of cracking and spalling phenomena in constrained and unconstrained thin discs respectively, subjected to laser radiation. In conjunction with the experimental work done, use was made of a heat flow analysis and a stress analysis program developed for this purpose. It was possible to theoretically predict the thermal and mechanical responses of a rock specimen to laser radiation and then compare them with experimental observations. Good correlations were obtained.

Jan 1, 1971