Search Documents

By W. J. Reagan

A SURVEY of the literature on bottom-cast practice gives but scant information as to some of the real facts concerning this most interesting method of steel manufacture, and some of the information available is very misleading.1 An exceptionally good description of this method of pouring or teeming is to be found in an English publication2 on the heterogeneity of steel ingots. Quoting from this paper: (a) With bottom teeming, the metal rises steadily and progressively in the mold with the minimum possible agitation, the main force of the stream coming from the ladle being broken down or retarded by the down gate or runner. Further, the stream of metal from the ladle, under these conditions of casting, is invariably main-tained at a much more continuous rate and is steadier than with top teeming. (b) In view of the facts referred to in (a) it follows that with bottom teeming the metal is not exposed to atmospheric oxidation to anything like the same degree as with top teeming. In this paper it is intended to detail briefly some of the advantages of bottom-cast practice and to discuss the possibilities of iron-oxide control in the basic open-hearth furnace. A description of the type of charge, ingot mold set-up, etc., is found in detail in an earlier paper.3

Jan 1, 1934

By C. W. Tomlinson

INTRODUCTORY THE analyses which have been made by the writer according to the method described below were made as part of Professor Withey's investigation of the concrete aggregates' of Wisconsin, in the hope of throwing light on the extent and nature of the influence of the mineralogical constitution of aggregates upon the properties of the concrete, and mortar made from them. This method was found most satisfactory after four weeks of experiment and modification. It attains an accuracy quite sufficient for the purpose of the analysis, and is fairly rapid. Mineralogical analyses may be thus made at a cost considerably less than that of chemical analyses of a similar degree of completeness. The results obtained by this method should not vary in any item by more than 1 per cent. of the total weight of the sample, and may be made very much better than this by the exercise of greater care in the microscopic counting (see below). The accuracy of the hand sorting 'is of course dependent upon the experience and carefulness of the analyst. . After a month's practice, the writer was enabled to turn out these analyses at the rate of four in 33 hr. of working time. It was found most economical to handle four samples at once. The samples analyzed weighed froth 290 to 340 g. each. The same method could be applied to larger or to smaller samples, within reason able limits. The following list covers the necessary apparatus and equipment: 1 good balance capable of weighing accurately to tenths (or, better, hundredths) of a gram, and of handling quantities up to 200 g. in weight. 1 Westphal balance, registering densities to two or three decimal places. 1 Meker or Bunsen burner, and gas supply. 1 nest of sieves, 10, 20, 40, and 100 meshes to the inch.

Jan 5, 1915

By J. W. Gilbert

DuriNG the sinking of the Needmore shaft, on one of the leases of the Eagle-Picher Mining and Smelting Co north of Webb City, Missouri, a very strong flow of water was encountered at a depth of 140 ft. Because OF the speed at which the water rose in the shaft after pumping was discontinued, and in order to speed up sinking operations, a new type of shaft bar and drilling equiprnent was devised, which saved approximately one hour on each shift This bar is made of an ordinary scren type shaft bar with a common drill arm attached to the bar by clamps and welded Into place To this drill arm is attached an ordinary arm clamp with set collar below Through this clamp is attached another drill bar of ordinary length so constructed that it slides back and forth and rotates around the perimeter of the shaft on the set collar A tripod saddle with legs removed is welded to the rotating bar, which enables the drill operator to drill holes at any angle completely around the shaft and also, after an arm extension, permits the drilling of the corner holes without removal of the rig from the saddle Upon completion of the drilling of a shaft round, all that is necessary for the complete removal of the drill machine and shaft bar is to engage the hoist hook through a. ¾-in. eye provided for that purpose on top of the bar and disconnect the air and water lines from the machine, thereby making it possible to pull the whole apparatus out in one piece. At no time is it necessary to remove the machine from the saddle Screw jacks are installed on the vertical bar to further ensure the rigidity of the shaft and bar arm. The accompanying sketch illustrates the details and method of setting up.

Jan 1, 1946

By R. I. Williams

Kennecott Copper's mining activities in Arizona are conducted by the Ray Mines Div., located in Ray, Ariz., in the Mineral Creek mining district about 60 miles southeast of Phoenix. The Ray orebody lies in a mineralized zone belted on the east, west, and north by well defined faults. The orebody consists principally of schist with intrusions of quartz porphyry and diabase. The dominant ore mineral in the schist and quartz porphyry is chalcocite, with some native copper, and in most areas the orebody has been heavily oxidized. In the diabase the dominant ore mineral is chalcopyrite. Ore deposition in the schist portion is very erratic, with no apparent structural explanation. In 1873 silver prospectors opened the mining district, but it was not until 1899 that an English company made the first major attempt to exploit the copper deposits. This venture failed because of improper sampling and limited development work. In 1904 D. C. Jackling, Seeley Mudd, and Philip Weiseman became interested in the Ray Copper Co. and the Gila Copper Co., which later merged as Ray Consolidated Copper Co. In 1926 the Nevada Consolidated Copper Co. took over Ray Consolidated and in turn was taken over by Kennecott Copper Corp. in 1933. The extensive program of surface and underground development and exploration begun in 1907 continued through successive changes of management and ownership to the present time.

Dec 1, 1956

By H. R. Brannon, R. J. Robinson, G. W. Kattawar

Accurate prediction of storm wave characteristics are needed for design of offshore structures. Statistical methods of random noise analysis provide techniques for predicting required wave properties. These techniques have been used to analyze and characterize storm wave profiles from Gulf of Mexico recording installations in 34, 65 and .98 ft of water. Correlations based on the results can be used to predict wave crest probabilities and wave shapes for a range of Gulf water depths and storm conditions. Example predictions of wave crest probability as a function of water depth for a particular set of storm conditions are given. INTRODUCTION Accurate predictions of wave crests and wave shapes are needed for design of offshore structures. With predictions of wave crests, platform deck elevations giving adequate protection from exposure to storm waves can be selected. Use of hydro-dynamic wave theories with the wave crest and wave shape predictions permits an estimate of the wave forces an offshore structure must withstand. Observation of ocean waves suggests use of statistical analysis for studying wave characteristics for water depths beyond the breaking wave zone; recent wave generation theories lend support to this approach. l-3 One of the most powerful methods of statistically analyzing wave profiles was introduced by Cartwright and Longuet-Higgins; most of the basic relations used were developed by Rice5.6 in studies of random noise theory. This method predicts wave crest elevation probabilities from two parameters characterizing a wave profile. The statistical approach also provides a means for predicting wave shapes. In the random noise model of a wave profile, surface elevation is represented as an infinite sum of sine waves with closely spaced frequencies and random phase angles. Power density is proportional to the sum of the squares of the amplitudes of sine waves having frequencies within a narrow band, and the distribution of power density as a function of frequency is called the power density spectrum, or power spectrum. The power spectrum characterizes an irregular sea, and hence finds use in motion studies of ships, barges and semisubmersible drilling platforms. From the power spectrum, a wave profile of any duration of time can, in principle, be calculated; this long wave profile depicts the many wave shapes to which a structure may be exposed. Thus, the statistical methods of wave analysis provide an approach to selecting wave shapes as well as wave crest elevations needed for design of offshore structures. For practical application of these techniques, power spectra and related quantities must be predicted from storm properties. Barber and Tucker 7 have reviewed correlations of wave properties and storm conditions. Their review summarizes work of Darbyshire,8 among others, in which a correlation of power spectra with wind intensity of the North Atlantic was developed. These results, plus more recent work by Pierson and Moskowitz and Kitaigorodskii,10 establish feasibility of correlation, but there is no theoretical basis for modifications extending the relations to other areas as remote as the Gulf of Mexico. Hence, to predict characteristics of Gulf of Mexico waves, a study of local observations is needed. This paper presents (1) a practical approach to computing wave profiles hat depict shapes of waves for use in force calculations, (2) a summary of relations for predicting probabilities of wave crest elevations, (3) correlations of parameters needed to apply these methods in the Gulf of Mexico and (4) examples of application of the techniques. THEORETICAL BACKGROUND The following sections summarize relations needed to calculate wave profiles and to estimate wave crest probabilities. These relations also identify quantities that must be related to storm

By C. F. Cornell, Henderson, A. F. Dunyon, D. A. Dahlstrom

IN processing magnetic taconites several steps of crushing, grinding, classification, and magnetic separation are required to produce a 60+ pct Fe concentrate. Usually the final concentrate is in a slurry form of 55 to 70 pct solids by weight and is further characterized by a particle size of 60+ pct -325 mesh. In taconite plants already completed or under construction the conventional method used to obtain pellets suitable for blast furnaces is to filter the concentrate slurry, ball the filter cake, and then harden the green pellets in a traveling grate or in a vertical shaft furnace. Large tonnages must be handled in minimum floor space, with reduced maintenance and lowest possible operating cost. Filtration must therefore achieve two objectives: 1) high filtration rate-in terms of pounds of dry solids per hour per square foot of filtration area-at a low filtrate solids concentration, and 2) a filter cake moisture that will always permit efficient balling within the normal fluctuations of plant operating conditions. If moisture contents are too high, balling may be impossible or result in a mushy ball without enough green strength for the firing operation.

Jan 3, 1957

By R. Hogg, D. W. Fuerstenau

Based on a simplified model for the motion of particulate materials in horizontal, rotating cylinders, approximate expressions have been derived relating the power consumption of a tumbling mill to its dimensions and speed of rotation and to the amount and nature of the charge. The basic assumptions underlying the model are that there is no slip between the charge and the mill shell, that the free surface of the charge remains essentially planar during rotation, and that there is no transfer of momentum from the material flowing down the free surface back to the mill shell. The relationships formulated from this model have been shown to be in excellent agreement with experimental results taken from the literature. While the requirements of the model are most clearly met at low speeds of rotation, the results appear to be valid even for speeds up to 70-80% of the critical speed. Poorer agreement between theory and experiment is found when the charge consists of relatively large particles (balls) and when the filling of the mill exceeds 50% of the available volume. Qualitative explanations of these deviations have been offered.

Jan 1, 1973

By Clarence Hicks

THE labor policy, of the Standard Oil Co. (New Jersey) is founded. first of all on paying at least the prevailing scale of wages in the community; on, the eight-hour day, with time and one-half for overtime; one day's rest in seven; sanitary and up-to-date working conditions; just treatment assured each employee; payment of accident benefits beyond the amount prescribed by the State compensation law; health supervision by a competent medical staff; payment of sickness benefits after one year's service; cooperation with employee in promoting thrift and better social and housing conditions; and assurance for a generous annuity at the age of 65, guaranteed for life after 20 years of service. Most of these features have been a part of the company's policy for many years, but it is only during the past two years that the cooperation of employees in determining these matters has been definitely assured through industrial representation. Industrial representation, in the Standard Oil Co., is a principle rather than a procedure. It is built upon the belief that personal association of those interested in any problem leads to a mutual understanding and a fair decision as to what is right. Fully believing in this, principle, representatives of employees and representatives of management evolved a simple plan, the basis of which is that it gives every individual employee representation at joint conferences on problems and fundamental principles affecting all those interested in the industry. It is based on cooperation, not antagonism; its operation makes perfectly clear both to management and to employees that their interests are identical, that mutual understanding and cooperation insure progress and success for all. Furthermore, experience has definitely shown that representatives of the employees are not only alert for the employees' interests but are as keen as the representatives of the management in determining and insisting upon fairness to the employer.

Jan 3, 1920

By R. A. Nadler and

Specimens of Ti-155A (Ti-5Al-1.3Fe-1.3Cr-1.2Mo), Ti-6Al-4V and Ti-4Al-3Mo-1V were hydrogenated, aged to high strength levels, and subjected to notched stress-rupture tests and tensile tests at two strain rates. Both Ti-6Al-4V and Ti-155A were relatively unaffected by hydrogen in amounts exceeding those found in commercially -produced material. Inconsistencies in the data and a relatively low initial level of ductility prevented an accurate determination of the hydrogen tolerance for aged Ti-4Al-3Mo-1V, but there was no evidence that this alloy was any more susceptible to hydrogen embrittlement than Ti-155A and Ti-6A1-4V. THE metallurgical literature has been considerably enriched in the past five years by the publication of the results of many investigations which were concerned with the effects of hydrogen on titanium and its alloys. Although it is not the authors' intention to provide a complete literature survey of this vast field, it is worthwhile to summarize briefly some of the important factors which influence the embrittling phenomenon in a - B alloys. Some of the influencing factors are those of strain rate, temperature, and composition. Hydrogen embrittlement in a - B titanium alloys is now believed to be a strain-induced phenomenon, and whether or not embrittlement occurs at high hydrogen levels depends largely upon whether sufficient time is available for hydride precipitation. This condition is fulfilled by tensile testing at very slow strain rates or by rupture testing smooth or, preferably, notched specimens over relatively long periods. Conveniently, maximum embrittlement occurs at or near room temperature. The presence B - stabilizing elements, in amounts sufficiently small to prevent an all -B or nearly all -P condition, promotes hydrogen embrittlement and this tendency is believed to be related to the amount of a - B interfacial area present. Aluminum, by increasing the solubility of hydrogen in A titanium, greatly reduces the danger of hydrogen embrittlement, while oxygen has been shown to have detrimental effects.' The preceding discussion is based on experimental work performed on annealed a - P alloys. This early work has shown that annealed Ti-6A1-4V and Ti-155A are relatively insensitive to the embrittling effects of hydrogen.' Although no work has been reported on annealed Ti-4A1-3Mo-lV, the alloy would be expected to exhibit somewhat the same insensitiv-ity as Ti-155A. In sharp contrast to the voluminous literature on annealed titanium alloys is the paucity of reported investigations on materials receiving commercial heat-treatment cycles. To date, the most notable contributions in this field have arisen from two separate investigations on Ti-3Mn-1Fe-1Cr-1V-lMo, the so-called 3Mn comple~. These investigations

Jan 1, 1961

By William P. Blake

The importance to the growing steel industry of the United States of a domestic supply of ferro-manganese or "spiegel" of a high grade, induces me to bring to your notice some details of the method by which a superior article is produced in the Austro-Hungarian Empire. At Reschitza, Hungary, and probably at Laibach also (the Krainische Industrie Gesellschaft), ferro-manganese is made in a blastfurnace, with charcoal as fuel, and limestone as the flux. The ore is a ferruginous mixture, containing about 37 per cent. of sesquioxide of manganese. It is silicious, and somewhat, resembles, in its appearance, the manganese ore from Red Island, in the Bay of San Francisco, California. It contains about 29 per cent. of silica and some alumina, shown by the subjoined analysis:

By Walter G. Perkins

As this particular product holds a place by itself, it seems desirable to give a paper dealing especially with it as a corollary to my paper entitled " The Litharge Process of Assaying Copper-Bearing Ores and Products, and the Method of Calculating Charges."* The process is first to convert the metallic copper into matte by the addition of sulphur, allowing the two elements to combine at the bottom of the crucible when heat is applied. The

Jan 1, 1903

By John C. Holtz

Hostility is a characteristic of the environment in underground mines. Nature opposes man's efforts to remove mineral deposits, and this condition is recognized when mining is described as winning minerals from the earth. Evidence of this conflict is the action of natural forces to close excavated passageways. In many mines, this behavior of the surrounding environment is an ever-present and ever-changing problem despite much research and empirical study. Geological conditions change abruptly and may result in rock bursts, the inrush of water, or variations in rock hardness. Although aspects of these problems will become intensified as the rate of mining increases, they are not considered in this discussion. Emphasis herein will be on the changes in the atmospheric environment. Men underground work in an ever-changing, alien, ambient atmosphere. Many conditions are encountered that will affect their health and safety unless properly controlled. Potentially explosive gases are released from minerals as they are mined or enter from the surrounding earth. Some mining methods generate noxious gases. Natural processes and diesel equipment can steal life-sustaining oxygen. Airborne dust may cause lung diseases when breathed by miners in excessive amounts and by affecting visibility, introduce safety hazards. Deep mines pose heat problems that may be aggravated by high-speed mining. The deleterious effects caused by these changes, and their mitigation, are subjects of this discussion. THE UNDERGROUND ATMOSPHERE Health and safety problems from changes in the underground atmosphere have been apparent since the beginning of mining. Alleviation of these problems has been by ventilation with normal air from the earth's surface that flushes away the vitiated mine atmosphere. The objective is to provide atmospheric conditions essentially similar to those that man is accustomed to on the surface.

Jan 1, 1970

By A. L. Field

WOOLSEY McA. JOHNSON, Hartford, Conn. (written discussion).¬When ;we regard the number of British thermal units running into the billions that-must be applied to metallurgical slags in the United States, we cannot but conclude that the physical chemistry of-slags is a very important subject when measured in dollars and cents. A further contemplation of the subject shows us that it has been hitherto treated in too purely a practical manner. It is needless to comment at length on the cost of these heat units and on the cost of fluxes to produce these metallurgical slags, for, it amounts to tens of millions of dollars annually. Accordingly, this research is of value to the country. But we must,all balance our results against our efforts. Therefore, while the speaker is unwilling to criticise unduly this meritorious research, lie does criticise it in the interest of the profession for the reason that it seems to him too highly theoretical. The article is much too, scientific to produce results at a minimum cost. Let us explain our meaning. It has been said that there are always two sides to a question. It may be further said that there are always three sides to a question, the two extremes and the middle ground. In any industrial research there are the highly theoretical side, the purely practical side, and the theoretico-practical side. To study a slag and be practical in the studying, there is something needed that represents in the laboratory (or in microcosm) what actually happens macrocosmically in the blast furnace. There is such a thing as the art of metallurgical research occupying the middle ground between theory and practice.

Jan 4, 1917

By D. O. Hobson

Zirconium single crystals of various specific orientations were fabricated by rolling or drawing. The resulting textures were determined and are discussed with respect to the deformation modes that produced them. The crystals deformed in a predictable manner by combinations of up to third-order twinning with three twinning modes and by slip. Twinning was found to play a major role in initial texture formation. Texture changes produced by slip occurred only at the higher reductions. The twinning sequences that produced each intensity peak during the initial reductions could be identified. Schmid factor criteria were found useful in predicting which deformation modes to expect for each crystal orientation and fabrication procedure. The possible application of these data to poly-crystalline material is discussed. PREFERRED orientation or texture has a significant effect on the properties of most materials, causing anisotropy in fabricated cubic metals and enhancing the natural anisotropy of noncubic metals. This study evaluates the effects of several fabrication methods on the textures formed from specific starting orientations of zirconium single crystals and, it is hoped, gives an insight into the effects of the same operations on poly-crystalline material. BACKGROUND In fcc and bcc metals, texture changes take place by gradual lattice rotations caused by the operation of one or more slip systems. Deformation twinning plays an insignificant role in the deformation of such metals. In zirconium and its alloys, however, and in many other hep metals the ability to twin allows very rapid texture changes to be made with very small amounts of deformation. The deformation systems found in zirconium and its alloys are prism slip and three twinning modes.1 Slip occurs on the {1010}< 1120) system. There is little or no appreciable basal slip in zirconium. The twinning planes, illustrated in Fig. 1, are {1012}, {ll2l}, and {1122}. Two twinning modes, the {1012} and the {ll2l} operate for a tensile stress along the basal pole. A compressive stress parallel to the basal pole is required for {ll22} twinning. These twinning operations cause a 35- to 85-deg reorientation of the basal pole. The {1012} twin is the predominant tensile twin at room temperature. The twinning shears, S, are shown in the figure. A criterion for predicting which deformation system will operate when a grain is subjected to a known stress state is the Schmid (orientation) factor. This factor gives the fraction of the applied stress that computer program was written2 to calculate the Schmid factors for the four deformation modes in zirconium. It assumed three orthogonal stress axes and considered ninety-one different orientations of the basal pole in one octant of this stress space. At each basal pole position the Schmid factors were calculated for seven positions of rotation at 10-deg increments of the unit cell about the basal pole. Schmid factors were determined for a total of 637 orientations and for twenty-four deformation systems in each orientation. The program listed the Schmid factors for uniaxial stress parallel to each axis and, to approximate rolling, or-thonormal biaxial stress was also considered. Fig. 2 shows the range of orientations over which the various types of deformation would tend to predominate in biaxial plane strain with the stresses, equal magnitude. The exact boundary position between regions of different deformation modes depends, however, on the relative values of the critical shear stress for each deformation mode. Fig. 2 is drawn on the assumption that they are equal and it therefore may be only approximately correct. It is also recognized that the biaxial stress analysis may not be applicable in certain crystal orientations. EXPERIMENTAL PROCEDURE Single crystals of zone-refined zirconium, produced by Wilson of this Laboratory,3 were electrical-discharge-machined to form specimens for rolling, tube-drawing, and rod-drawing studies. Specimens were rolled at room temperature on 2-|--in.-diam hand-powered rolls from three different starting orientations: 1) the basal plane parallel to the rolling plane and the [1120] in the rolling direction, (0001)[ll20]; 2) the (1120) plane parallel to the rolling plane and the basal pole in the rolling direction, (1120)[0001]; and 3)_the (1120) plane parallel to the rolling plane and the [1100] in the rolling direction, (1120)[ll00]. Drawing specimens were cut with the [0001] direction as the drawing direction in the tube blank and [1120] as the drawing direction in the rod specimen. The drawing

Jan 1, 1969

By A. U. Seybolt, F. J. Norton

A standard technique for heat treating small metallurgical samples where no appreciable contamination from the atmosphere can be tolerated is that of sealing small samples in evacuated fused-silica tubes. Since vitreous silica is relatively impervious to diffusion of gases, even at temperatures approaching the devitrification range, around 1100°C, this simple procedure has been very widely adopted as a standard technique in metallurgical research. Many workers have recognized that, with metals of fairly high reactivity, insulation from direct contact with the SiOz envelope is desirable in order to avoid displacement reactions of the type M + SOz-- MOz + Si(in M). It is not so generally known, however, that the &apos;rate of permeation of oxygen from the air through the SiOz enclosure at tem-

Jan 1, 1964

By A. B. Stevens

IN the calculation of oil and gas reserves by volumetric methods, it is necessary to know the volume of the reservoir available for the storage of the oil or gas. To obtain this information, a number of methods for determining both total and effective porosity of reservoir rocks are used. For the determination of the total porosity, or the porosity that considers all of the pore spaces, connected and isolated, the Russell7,8,9 and the Melcher-Nutting1-6 methods are the best known and most- widely used in the petroleum industry. These methods have disadvantages in that they give the total porosity of the samples and in that the samples are reduced to grain size in the determination. In many sands there may be little or no difference between total and effective porosity but in other sands there may be considerable difference between the two. For the estimation of oil-and gas reserves the effective porosity of the reservoir rock always should be used. Of the methods that have been developed for the determination of the effective porosity of reservoir rocks, or the porosity that considers only those pore spaces that are connected, the best known are the so-called Boyle&apos;s law6,10-13, and the Washburn-Buntings.5,6,11 methods. The Wash-burn-Bunting method is probably the most widely used because it gives effective porosity, it is rapid, and the apparatus is inexpensive. This method employs a special porosimeter in which the core sample is placed in direct contact with mercury. This method has disadvantages in that, as a result of the high vacuum created in the pore spaces, mercury is drawn into the openings, making it impossible to use the sample for a check determination and also ruining the sample for any further test, such as permeability. The purpose of this paper is to describe an appa-ratus employing the same principle as the Washburn-Bunting method but so designed that the core sample does not come in contact with the mercury in the porosimeter.

Jan 1, 1939

By F. K. Pence

THE reduction of the firing of clay wares to a science has been one of the most difficult problems of modern ceramic engineering. The number of factors involved in the treatment of these wares has been such a complicated composite of the chemical and the physical properties that, according to the old practice, results depended rather on the art of the operator than on any scientific data available. The combined influence of the chemical and physical properties of clay minerals renders it difficult to apply the data obtained in one operation to the forecasting of details to be applied in another. In maturing clay-ware bodies by the application of heat, the chemical reactions involved are, in general, incomplete. The object frequently is to secure a certain physical quality, as density, color, or strength, rather than any particular chemical composition or development: This is more generally true of the so-called crude clay products. In the case of certain more high-grade wares, as the porcelains, it is necessary to reach the temperature required to bring about a certain molecular development or crystalline structure; but even here, time and temperature are at work and must be considered jointly. The conditions attending the firing of clay wares has led to the use of certain devices in the measurement of the progress of the firing process whereby the influence of the various burning factors on the clay composition under fire is indicated. In the simplest application of this practice, samples of the ware itself are so placed as to be drawn for observation at various intervals during the burn. Although the appearance is affected by the quick cooling treatment, by experience, this practice is successfully used, particularly in the brick industry. The settle of the setting of brick, as measured from the top of the kiln may also serve as a guide in the firing operation. Another example is found in the stoneware industry, where the practice of arranging test pieces made of the same composition

Jan 9, 1919

By Alvin Kaufman

ANTHRACITE mining in the United States is concentrated in a 480 sq mile section of north- eastern Pennsylvania. The producing area is broken up into four fields, known as the Northern, Southern, Eastern Middle and Western Middle fields. These areas represent intricately folded coal measures in synclinal residuals left by erosional forces. Destruction by erosion has eliminated some 95 pct of the original coal. However, discounting the 5 billion tons removed to date, 8 billion tons are believed to be still recoverable.

Jan 3, 1953

By Donald Barton

THE purpose of this torsion balance survey and the quantitative calculations was to delimit the extension of the cap rock at the Hoskins Mound salt dome. The sulfur ore in the Gulf Coast sulfur-bearing salt domes occurs in the lime rock, which is the outer layer of the cap-rock mass, and also in the underlying gypsum zone. The status of the exploration and exploitation of the Hoskins Mound dome at the date of this survey is shown by Fig. 1. The mound had been covered by the very early prospect wells of the Mound Oil Co., and the later and more numerous prospect wells of The Texas Company. The Freeport Sulphur Co. was producing from the flank wells in the southwest quadrant. The limits of the cap were surmised to lie inside the centers of quad-rangles 4F, 3F, the center of the NE. ¼ of 2E, and the north line of 2D. That surmise was based partly on the data of Fig. 1 and partly on the position of the edge of the topographic mound. The management of the Freeport Sulphur Co. wished to block out the extent of its ore reserves with a minimum of expenditure. The management was informed by the writer that no geophysical method could map the presence or quantity of sulfur directly, or determine the presence and quantity of the lime-rock cap independently of the rest of the cap, but that a reasonable probability existed that the approximate position of the edge, the depth and the thickness of the cap-rock mass as a whole could be determined through quantitative calculations based on the data of a very careful torsion balance survey. Considerable lime rock would probably be present, of course, wherever much cap rock was present. This paper presents the data of the survey, our calculated prediction of the configuration of the cap rock, and the degree of confirmation by the subsequent drilling. The survey was made by the Geophysical Research Corporation, under the direction of the writer. The work of the calculations was done by Andrew Gilmour, then assistant to the writer.

Jan 1, 1936

By C. P. Parsons

CALIPER logging is a practice of measuring the variations in the diameter of the open hole in a well. This information is useful for many purposes, among which are: Determining the volumetric capacity of the portion of open hole to be cemented; the amount of gravel to be used for gravel-packing a well; the size and location of seat for a packer to be placed in a well; studying the effects of nitroglycerin shots; studying the effects of acidizing; studying the cause of drill-pipe failures; studying drilling technique; geological correlations. This is a new practice in oil fields and is eliminating considerable guesswork.

Jan 1, 1942