Search Documents

By Raymond M. Howe

Some time ago, a prominent engineer asked a representative of the firebrick industry to prepare a comprehensive paper on blast-furnace refractories. It was to have been the purpose of this paper to gather practical experiences from widely different sources, in the hope of determining what kind or kinds of firebrick were best adapted for certain uses. This engineer sent questionnaires to the large consumers of blast-furrace linings and stovebrick and received very detailed replies as to their experiences. These replies are conflicting, but, having been turned over to the writer, form the basis of this attempt to meet the request. Because of the impossibility of making final recommendations at this time, a few of the more interesting and commonly known methods of studying refractories are also discussed, as well as the more recent developments in this field. The first reply to the questionnaire stated that good service was being secured from the linings. This satisfactory condition was attributed to the use of a very good distributor. The writer believed that manufacturers try to and do produce a good product and that the proper handling of equipment is of the utmost importance, if good results are to be secured. The type of bricks used was not mentioned. The second reply stated that good life was secured from the furnace linings, but that the writer had had soft-fired stovebrick crumble and, for that reason, preferred a hard-fired product for use in this position. The type of bricks used was not mentioned. The third reply stated that firebrick had crumbled from the mantle up; the cause was not known. The fourth reply stated that the stove linings were satisfactory. Hand-made furnace linings failed after.4 years' service so a steam-pressed lining- was installed which was still good after 4 years of service. Consequently, a second steam-pressed lining was installed but this disintegrated at the top after the furnace had been in blast 7 months. The firebrick manufacturer attributed this failure to the expansion of iron blocks that had been installed at the stock line to prevent erosion. The fifth reply stated that the present "hard-burned" hand-made furnace lining had worn away very uniformly to the depth of only 5 in.

Jan 1, 1920

By K. A. Natarajan, I. Iwasaki

The meaning and the utility of redox potential (Eh) measurements in sulfide flotation systems are examined. Since some preliminary plant Eh and laboratory flotation data were available, experiments were made to establish the pH range at which a platinum electrode might be used for such measurements without much difficulty in aerated systems. Triangular wave voltammetry was used to study the surface conditions of the electrode immersed in pyrrhotite suspensions at different pH. The measured Eh both at the plant and the laboratory is interpreted in terms of the experimental water-oxygen line.

Jan 1, 1974

By R. D. Vaughn

The limiting cases of non- Newtonian fluids flowing inside a concentric annular duct are developed without using a model of the fluid behavior. The solutions provide limits with which to test the various models of fluid behavior such as the power law and Bingham plastic models. The results of previous theoretical work are discussed in terms of limiting cases. This limiting case study also shows that experimental work on flow of non-Newtonian fluids in annular ducts should be confined to ducts for which the ratio of the radius of the inner wall to that of the outer wall is less than 0.3 and preferably less than 0.2. INTRODUCTION During the last 10 years the problem of laminar flow of non-Newtonian fluids in concentric annuli has received much attention large1y because of its application to the hydrodynamics of the wellbore. Recently solutions utilizing the power law1,2 and Bingham plasticl,3,4 models have been published. In this paper the method of limiting cases, which has been successfully applied to laminar-flow heat transfer516 will be applied to the problem of flow of non-time dependent, non-Newtonian fluids through annuli. This method permits solutions for the limiting cases to be made without using a model of unknown validity. The solutions, therefore, provide limits with which to test the various models which have been or will be proposed. A pertinent conclusion concerning the region of experimental work is also provided. DEVELOPMENT OF LIMITING CASES The limiting cases for the axial flow of fluids in concentric annuli may be defined with reference to Fig. 1. It is possible to define two limiting cases which pertain to the physical dimensions of the annulus. First, the annulus must degenerate to a circular pipe as the radius of the inner wall decreases or, as k = (k R/R) ? 0. Second, the annulus must approach the limit of parallel plates of infinite extent as the spacing between the inner and outer tubes becomes small in comparison with the radius R of the annulus, or as k?1. It is also possible to ascertain three limiting cases which pertain to fluid behavior. With reference to Fig. 2, as a fluid becomes progressively more pseudoplastic, the shear stress-shear rate relationship progressively approaches the indicated horizontal line more closely. At this limit the shear stress becomes independent of the shear rate. At the other extreme of increasingly dilatant behavior, the vertical asymptote is approached. Intermediate between these two limiting cases lies the case of the Newtonian fluid. Fluids which exhibit a yield shear stress also approach the limiting case of "infinite" pseudoplastic behavior. The remainder of the theoretical development is concerned with the description of and the solutions

By W. A. Backofen

THE preferred orientations, or textures, resulting from many of the various methods for testing and forming metals have been the subject of numerous investigations.1,2* Despite this large amount of work, however, only a few limited studies have been made of the texture that is developed by torsional deformation. Ono3 found that in severely twisted wires of copper and aluminum a [Ill] direction lies parallel and a [1101 direction perpendicular to the longitudinal axis of the wire. Sachs and Schiebold4 have reported that a double-fiber texture exists in a twisted aluminum wire with both the [Ill] and [loo] directions parallel to the axis of the wire. Twisted iron wires have also been examined by Ono.8 Both the [1101 and [1121 directions were reported as parallel to the axis of the wire. Goss5 concluded from a study of twisted rods of a low-carbon steel that the preferred orientation existing at fracture is quite complex, but that many grains have a [1101 direction parallel to the axis of the wire. In addition to the earlier experimental work, some suggestions have been made about the possible nature of the torsion texture. These suggestions are based on the results of many experiments which indicate that the cold-working texture of a particular metal is largely determined by the geometrical change in shape that the metal undergoes during plastic deformation.1,6 Hibbard and Yen7 have considered the problem of deformation textures and have presented an analysis which is able to explain why equivalent changes in shape should yield similar textures. Therefore, a knowledge of the principal strains associated with torsional deformation would seem helpful in the interpretation of the torsion texture. The necessary analysis has been made of the state of strain in an element of metal lying in the surface of a cylindrical rod or tube that has been subjected to pure torsion.8,9 This analysis shows that the directions of the principal normal strains rotate continuously within a torsion specimen while it is being twisted. After the first infinitesimal amount of twisting, these directions make angles of 45" with the longitudinal axis of the bar. They rotate from this position as twisting proceeds, and after an infinite amount of twisting, the direction of the principal tensile strain is perpendicular, and the direction

Jan 1, 1951

By Suresh P. Babu, Joseph W. Leonard

The ultimate objectives of comminution should be to reduce material to some specified size while producing a minimum of undersize or fines, with less power, higher throughputs, and with more compact machinery. Attempts to achieve these objectives have been only partially successful, since gains in some areas are achieved at the cost of concessions in other areas. An example of some of these trade-offs can be found in the closed circuit crushing operations of the anthracite and crushed stone industry where, in order to produce a minimum of unprofitable fines, unfavorable concessions must be made in the size of the crushing facility where 2 or more crushing stages are interphased by 2 or more screening operations. This paper discusses experiments with a new process which attempts to achieve some, if not all, of the comminution objectives in a single pass operation without undesirable concessions; or, at the very least, to achieve more than is possible with systems in use today. These objectives are sought by use of water-flushing to enhance comminution. The crushing of coal and other minerals is a mature technology that is long overdue for a careful re-examination. Crushing of coal is generally achieved through the use of rotary breakers and roll crushers. Water-flushing, as envisioned here, appears to have potential application in the following areas: 1) For primary raw coal crushing or for secondary crushing of rotary breaker products. 2) For use as a size reduction and/or concentrating step for crushing coal mine refuse from present production or from existing refuse dumps. 3) For possible future application in underground preparation interphased with continuous mining machinery. Size reduction with conventional methods is known to be an inefficient operation when the increase in surface energy of the material crushed is compared with the input energy. A simple breakdown of the energy consumption in size reduction, given by Orr, is shown in [Fig. 1]. It is believed that most of the energy supplied is lost in the form of interparticle friction.2 Hence, the removal of fines immediately after their formation or the implementation of steps to prevent their formation, based on reduced friction, will reduce the energy requirements of the communition operation.3 A detailed discussion of the mechanism of size reduction is available in other literature.3-5 Even though the closed circuit crushing operation is designed to carry the fines away from the crushing zone, it is still inadequate for instantaneous removal of fines. The present investigation advocates the use of a flowing liquid medium to remove the crushed product immediately after size reduction. Unlike the wet-grinding methods, no constraints are required for the liquid flow rate, and, also, the liquid medium can be used in primary crushers like jaw crushers, hammer mills,

Jan 1, 1978

By E. H. Rose

THE question is often pondered whether the flotation process is still an art or has become a science. The fact is that flotation is a science in so many variables that only art can blend them. It is demonstrable that no less than one hundred variables are involved in any flotation operation, most of them immeasurable on a routine basis. The behavior of every one of them is always governed by orderly and unchanging law, as no man can doubt. There is nothing truly indefinite about that behavior; the only indefiniteness is in our knowledge of it, either in general or from hour to hour in the circuit. In dealing with a simultaneous equation in, say, one hundred variables, all not only affecting the outcome to some degree but many influencing each other as well, it is small wonder that the mineral-dressing profession presents a case history of debate and controversial opinion. The statement of the subject of this symposium-a symposium on flotation machines-seems to delimit and define the matters to be considered and at least the general nature of the conclusions sought. Nevertheless, in such a meeting it is not possible to meditate upon all the variables that do in one way or another affect performance of flotation machines. To attempt it would be much like trying to operate a hundred-ring circus. Perverse variables being what they are, one could expect the elephant in ring 36 to squirt a trunkful of water at the tightrope performer in ring 37 to ruin that artist's act, just as our learning to depress pyrite in the early 1920's ruined the act of the formerly faithful old Callows. HONEST DISAGREEMENTS Selective flotation dates from 1922 or 1923, when several plants established their regular flotation operations on a selective basis. Since then, two decades of efforr have gone into the development of better and better flotation machines. Many have come and gone. The competition has simmered down to perhaps a dozen machines, each one of which is staunchly defended by some operators as being the best for their particular jobs, and as scornfully dismissed by at least a few others elsewhere as being positively the poorest for theirs. These disagreements are honest disagreements, honestly arrived at after plenty of sweat. In many a flotation plant, one machine has been tried out against another under conditions as fair as they could possibly be made. Sometimes the results are on a par but more often one machine shows a consistent and unmistakable margin of superiority over the other. In equally honest and enlightened tests, machine A may win over machine B in one place, and machine B over machine A by as great a margin in another. This paper purposes to identify some of the more prominent reasons why this is so,

Jan 1, 1944

By W. S. Stahmann, F. W. Bowdish

Previously published experimental data showing that both collectable and non-collectable sulfide films may be formed on chrysocolla were analysed, and chemical mechanisms were proposed for the formation of the films. A special technique was developed by which the quantity of sulfur adsorbed was determined for samples sulfidized under different conditions of pH and soluble sulfide concentration. The data on sulfur adsorption were used together with the expression for the equilibrium constant for the proposed reaction to indicate the validity of the chemical mechanism theory. A recent paper 1 about contact angle studies on chrysocolla reported the effects of pH value and sodium sulfide concentration during sulfidization upon the character of the surfaces produced. In each experiment the surface of a specimen of chrysocolla was prepared by grinding it with fine abrasive and washing it in tap water. The specimen was then placed in the sulfidizing solution for 10 min, rinsed in tap water, treated for 15 min in a solution containing 30 mg of potassium amyl xanthate per liter, rinsed in distilled water, and tested for air adhesion in a contact angle apparatus. The results, when plotted as in Fig. 1, showed an island representing conditions giving air adherent or collectable surfaces surrounded by conditions giving non-collectable surfaces. Particular interest may be attached to the region of non-collectability to the right of and above the island in Fig. 1, and to the boundry curve separating these two regions. It is apparent that at any pH from 4.0 to 6.0, where a collectable surface may be produced, a sufficient increase in the sulfide concentration results in a non-collectable surface. Thus it appears that too much soluble sulfide has a depressing effect upon the mineral, just as it has in sulfide flotation. This paper presents some speculations regarding the chemical mechanisms by which the collectable and non-collectable sulfide films may be formed and reports on a physical-chemical study intended to support these speculations. THEORETICAL CONSIDERATIONS The experimental results presented in the previous paper were analysed in several ways in an attempt to understand better the chemical mechanisms involved. For several points on the boundary to the right of the region of contact in Fig. 1, molar concentrations of H+, OH-, HS-, and S= ions, as well as various ion concentration products, were calculated. Following the reasoning of Wark and Cox, 2,3 no single kind of ions may be credited with causing depression of the surface because none of them have a constant con-

Jan 1, 1968

By J. B. Chatelain, M. F. Dufour

FLUID jet mills, employing a compressible fluid to grind materials to the subsieve range, was developed in the early 1930's, and the subsequent acceptance of these units was the result of their ability to pulverize solids that, because of physical properties, could not be processed by other attrition methods, such as ball, pebble, and hammer mills. Also, the fluid energy pulverizer is the only grinding device that will discharge continuously a 5-micron or smaller product. Simultaneous ultra-fine grinding and classification is the widest application of this unit. Jet mills may be used to advantage to reduce particle size of solids suspended in liquids, for coating one material with another, and effecting chemical reactions and changes in physical characteristics other than a reduction in size. Materials that can be processed by this grinding method include nonmetallic and metallic minerals, ores, metals, pigments, insecticides, fungicides, pharmaceuticals, plastics, dyes, and numerous other organic and inorganic products. Grinding principles utilized in the fluid mills available on the market are basically the same, the major difference being in the shape of the, grinding and classification chamber. Grinding in fluid jet pulverizers is accomplished by collisions between particles of the material being ground with the energy being supplied by compressed fluids entering the grinding chamber at high velocities. The "Micronizer" is a fluid energy mill employing a relatively flat cylindrical grinding chamber. Fig. 1 shows general construction details. The mill shown is equipped with a venturi type feeder using a compressed fluid to inject the feed into the grinding chamber. The energy consumed in forcing the feed into the grinding chamber against the mill pressure is, in some cases, as much as 40 pct of the total required for processing. Recent improvements, using a compression screw feeder as shown in Fig. 2, can reduce this to 1 or 2 pct of the total energy requirements. Grinding Grinding, as carried out in the. Micronizer involves the action of gaseous jets emerging from nozzles located in the peripheral wall of the grinding chamber. The axes, of the jets are tangential to a circle of smaller diameter than the grinding chamber as is shown in Fig. 1, and the gases entering the chamber maintain a high rotational velocity. The feed introduced into the mill is accelerated by the rotating gases and is thrown to the outside where a portion, coming in the zone of action of a nozzle, is further accelerated tangentially and inward. Violent collisions occur between the particles so accelerated and other particles circulating at a slower rate in a thin band near the periphery. It is estimated over 90 pct of the reduction in Micronizers occur as a result of impact within a fraction of an inch of the orifice. Observations also indicate that size reduction is independent of any interaction with the walls of the

Jan 1, 1952

By H. H. Pentz

THIS paper gives the derivation of a practical formula for the calcu-lation of slopes in seismic reflection prospecting. The derived formula is an approximation and can be used where the slope of the reflecting horizon is less than 250 ft. per 1000 and the depth to the reflecting horizon is greater than 2500 ft. The slope of sediments in oil regions is generally considerably less than 250 ft. per 1000. This is particularly true of the Gulf Coast, with the exception of the salt domes, which usually have the sediments at a greater slope than 250 ft. per 1000.

Jan 1, 1937

By David R. Poirier

Activity data of carbon as a function of both temperature and composition throughout the stable austenite range is correlated by mearts of an equation derived from a quasi-chemical model. The carbon activity data of austmite for temperatures between 800° and 1200°C are utilized in conjunction with the activity of carbon calculated for the y solidus using the activity of carbon in liquid iron and published austenite-liquid equilibria. The results agree very well with Chip-man's correlation; however, a small difference in the activity of carbon in the high-temperature range of the austenite field is evident. Excellent agreement is found for the heat of solution of graphite in infinitely dilute austenite; from this study the value is 10,550 cal as compared with Chipman's value of 10,680 cal. AS part of a program to study microsegregation in dendritic solidification of ternary Fe-C-Cr alloys, it was desirable to be able to describe the equilibria between austenite and liquid iron in Fe-C-Cr alloys. In this regard, it was necessary to correlate existing data on the activity of carbon in Fe-C austenite as a function of both temperature and composition. At that time, Chipman's analysis1 of the thermodynamics of binary Fe-C austenite was not available. It will be shown that this study and Chipman's study agree rather well throughout the stable austenite range of temperature and composition; however, some small differences appear at temperatures greater than the eutectic temperature. Benz and Elliott 2 presented isoactivity lines for austenite superimposed on their revised Fe-C phase diagram. Using an expression from Darken and Gury 3 representing Smith's4 activity data between 800" and 1000°C, they found that the activities extrapolated above 1000°C to the solidus did not agree with the activities determined from the corresponding liquidus compositions. It is the purpose of the following argument to reconcile carbon activity data of austenite with the activity in liquid Fe-C alloys as determined by Rist and Chipman. 5 In addition, a simple analytical expression is sought for computational convenience. ACTIVITY DATA OF CARBON IN ZRON Fig. 1 shows the activity of carbon in Fe-C austenite as determined by Smith, 4 Schenck and Kaiser, 6 Scheil et a1.,7 and Bungardt et al.' The lines are merely drawn to separate the data into the respective isotherms. These data are inadequate to determine the activity of carbon at temperatures greater than 1200°C. The activity coefficient in Fe-C liquid alloys was assumed by Rist and chipmans to obey the following

Jan 1, 1969

By Charles R. Holmes

MORE than 70 igneous pipes and dikes are known to occur in Cambrian sediments throughout an approximately circular area of about 75 sq miles, in southwestern Ste. Genevieve County and southeastern St. Francois County, Mo., across the southern portion of the Farmington anticline, which is outlined in fig. 1. From evidence obtained from fossil fragments taken from some of the intrusives, and from the similarity in composition of the more basic intrusives to those of known age in surrounding states, these pipes and dikes are believed to be at least post-Devonian and probably Cretaceous in age. As first postulated by Rust[1], these intrusives are believed to represent explosion tubes, or diatremes, punched through great thicknesses of solid rock by gaseous pressure.

Jan 11, 1950

By S. Floreen, R. M. Pilliar, H. W. Hayden

The fracture behavior of a 50 pct Cu-50 pct Fe mi-croduplex alloy, laminated composites of copper and iron and an extruded 50-50 Cu-Fe elemental powder composite was studied. Very low ductile-brittle transition temperatures were achieved in all cases, but for different reasons. In the microduplex alloy both the initiation and also the propagation of cleavage fractures appeared retarded by the very small in-terphase distances. In the composites, crack propagation through the sumples was prevented in most cases by delamination fractures perpendicular to the advancing cracks. These delaminations occurred at different regions and by different mechanisms in the various composites. In the extruded powder composite, de-lamination appeared to take place along preexisting flaws. In the crack arrest geometry of the laminated plates, delamination took place by localized shear fractures within the copper near the Fe-Cu interfaces. In this case delamination was enhanced by thicker laminate layers, and by having the resistance to shear failure of the copper sufficiently low compared to the toughness of the iron. BRITTLE fracture in engineering materials has long been a problem, and many different ways of preventing it have been considered. One method that has been of growing interest lately is to prevent crack propagation by the introduction of mechanical discontinuities into the structure. These discontinuities may act in several ways. They may simply act as crack stoppers. They may introduce secondary fractures such as de-laminations that deflect the initial crack into new, less damaging directions. Alternatively, they may subdivide a fairly large bulk sample that would have been loaded in plane strain, for example, into a number of subunits that are individually loaded in plane stress and thus are more resistant to fracture. Other mechanisms, or combinations of mechanisms, are also feasible. A number of methods exist for introducing mechanical discontinuities into a structure. Composites by their nature have discontinuities in structure, and numerous studies have shown that fracture propagation in materials of this type can be radically changed by suitable control of the composite parameters. Of particular significance to the present work are recent investigations of layered composites made by joining high strength steel sheets by various means.'-4 These studies have shown that through proper control of the mechanical properties of the bonds joining the sheets it was possible to introduce delamination fractures that markedly improved the overall toughness of the composites and in some cases completely prevented through-the-thickness fractures. Another technique for introducing structural discontinuities is simply to use a two-phase alloy. It has been recognized for many years that a small amount of a second phase may improve toughness either by homogenizing plastic flow and thus preventing localized stress concentrations that nucleate fracture, or by interacting with an advancing crack. In most of these studies of two-phase materials, the decreases in ductile-brittle transition temperatures produced by the second phase were relatively small. More recently, work on two-phase stainless steels having a very fine grain microduplex structure has shown that the presence of on the order of 40 to 50 pct of a tougher second phase may lower the ductile-brittle transition temperature of the brittle phase by approximately 300°F. 5-7 In these alloys delaminations were seldom observed. The tougher second phase appeared to minimize the ease of both the initiation and the propagation of cleavage fractures. These results show that both the composite approach and the microduplex alloy approach are effective methods of preventing brittle fracture. Therefore, it was of interest to compare the fracture behavior of a microduplex alloy with composites made from the two-phases that were present in the alloy. To simplify this comparison the 50 pct Cu-50 pct Fe system was selected for study. At low temperatures the equilibrium tie line phases in this system are essentially pure ferrite and pure copper. A 50-50 alloy was cast and hot worked to produce a microduplex structure. Two types of composites were studied; laminated structures prepared by roll bonding iron and copper sheets of the tie line compositions, and an extruded powder composite made from high purity elemental powders. The fracture behavior of these materials was then compared. EXPERIMENTAL PROCEDURE Alloy Preparation. The 50-50 Fe-Cu alloy and the components for the roll bonded composites were prepared by vacuum induction melting 30-lb heats using electrolytic grades of iron and copper as charge materials. A carbon boil was used to deoxidize the melts. Small additions of copper and iron were made to the iron and copper heats, respectively, to approximate

Jan 1, 1970

By P. Marier, T. R. lngraham

The kinetics of the sulfation of MnO,, MnzO3, and Mn3O4 in SO,, SO3, and O, mixtures was examined and the descending order of sulfation rates at temperatures near 400°C was found to be Mn,O3 > MnO, > Mn3O4. The respective activation energies for the thermal decomposition of MnO, and Mn,O, are 39 and 47 kcal. At 900°C, the thernzal decomposition of MnSO, to MnzO3 is slower than that to Mn3O4. The respective activation energies are 62 and 51 kcal, respectitely. MANGANESE is used to improve the hot workability of steel in the proportions of approximately 13.5 Ib of ferromanganese per ton of steel produced. This requirement accounts for about 95 pct of its large industrial market in North America. The remaining 5 pct is used in the battery and chemical industries. In most North American ores, the percentage of manganese and the manganese-to-iron ratio are not suitable for the direct production of ferromanganese. Hence, most of the North American requirements for manganese are satisfied by importing ore. Typically, many of the studies done on native low-grade manganese resources have been directed toward the production of ore substittes" and the recovery of manganese from open-hearth slags.3 Of the wide variety of processes which have been proposed, the most popular involve compounds in the Mn-S-O system. The thermodynamic properties of manganese and its compounds were reviewed by ah' in 1960 and, more recently, lngrahams discussed the thermodynamics of some of the reactions involved in the Mn-S-O system at normal roasting temperatures. The conditions for producing manganese sulfide during the reduction roasting of manganese sulfate are discussed by Fuller and Edlund.9 A novel scheme was proposed recently by zimmerley7 for utilizing waste sulfur dioxide from stack gases to recover the manganese from ocean-mined manganese nodules. Very little of the work published on manganese compounds has been related to reaction rates. Singleton et 1.' studied the rates of reaction on the MnO-C and Mn7C3-3MnO systems and observed linear and parabolic kinetics respectively in the systems. Tatievskaya et a1.' studied the low-temperature reduction of Mn&, MnO,, and Mn& in HZ and CO, and reported activation energies in the range 1628 kcal. In this paper, the rates of some of the decomposition and formation reactions involving MnSO4, MnOz, MnzO3, and Mn3O4 will be examined after the conditions for the thermodynamic stability of the individual compounds have been designated. CONDITIONS FOR STABILITY OF MnSO4, MnOz, MnZO3, AND Mn3O4 The areas of stability for h'hSO4, MnOz, MnzO3, and h3O4 were established from the data of Mah4 and Ingrahams and are shown in the predominance area diagram,10 logpq- logpsq, in Fig. 1. The diagram is drawn for two temperatures, 700°K, solid lines, and 1100°K, dotted lines. The sketch for the lower temperature includes the conditions likely to prevail in the Zimmerley patent7 when manganese nodules react with sulfur dioxide and that for the higher temperature indicates the conditions for recovering MnzO3 or Mn3O4 from MnSO4 during a roasting reaction. From the fact that the boundary between the areas of stability of MnOz and hSO4 at 700°K is parallel to the abscissa, it is evident that MnOz and SO2 should react together to produce MnSO4, irrespective of the oxygen pressure in the system. If the source of sulfur for sulfation were from waste flue gases, it is likely that the oxygen content of the gas stream would be more than sufficient to oxidize any MnsO4 to MnzO3, 107 atm of O2 required, or even to convert any Mnz03 to MnOz, 0.02 atm OZ required, prior to sulfation. At 1100°K, the diagram indicates that MnSO4 may be converted directly to either MnzO3 of Mn3O4, depending upon the prevailing partial pressure of oxygen. When the gas stream contains more than 1 pct Oz, logpq = -2, only MnzO3 would be recovered from an experiment done under equilibrium conditions. At oxygen partial pressures of less than 1 pct, one would expect to bring about a reversible exchange between MnSO4 and Mn3O4 by appropriate adjustment of the partial pressure of SOZ. These various reactions will be described in the subsequent kinetic experiments.

Jan 1, 1969

By Fred Chappell

Pyrophyllite, a hydrous aluminum silicate, physically similar to talc, receives its name from the Greek word Pyr, for fire and phyllite, a rock or stone. Firestone refers to its first recorded use as firestones or hearthstones. Composition and Properties Pyrophyllite is an aluminum silicate A12O34SiO2H2O (alumina 28.3 pct, silica 66.7 [ ] pct, water 5.0 pct) (Table 1). Vanderbilt1 gives pH value of pyrophyllite as 5.6 to 8.4. Pyrophyllite is usually white or cream, though it may be found in shades of pale green, pale yellow, buff or light gray, and in darker shades and other colors principally due to oxidation of contained iron minerals. It is opaque to translucent in thin sections. Its hardness is 1 to 2 in the Mohs scale. Its specific gravity is 2.8 to 2.9. Its luster is pearly to dull; it is recognized chiefly by its micaceous structure and cleavage, and its soft greasy feel. Two other varieties occur, one in which there are radiated needles in the crystalline form, and there is also a massive homogeneous structure found. Fine grinding reduces pyrophyllite to fiat plates or scales but aggregates of minute foliated plates may be formed.1 Distribution of Deposits Pyrophyllite is found in metamorphic rocks throughout the world but it is only in comparatively recent years that it has assumed much commercial importance. The principal

Jan 1, 1960

By Wilford S. Wright

FOR the past four years the management of the Black Hawk Consolidated Mines plant at Mogollon has conscientiously kept accurate records pertaining to cost of operation and the performance of certain equipment. These records have been valuable in coordinating the work in the mine, mill and power plant. Also, as to quantity and kind of equipment and supplies most suitable from the standpoint of economy and dependable operation, they have served as a guide. Through comparison with records at other mines, where the same things are being done in a different way, they have pointed out mistakes to be avoided. No outstanding accomplishments, either in costs or performances, are revealed; in fact, some of the results are perhaps quite inferior to those obtained at similar plants, but it is with the thought that more records should be published for the benefit of the mining profession that the author presents these data. To other operators and to mining engineers who are called upon to make estimates for prospective operations, the information herein should be helpful. GENERAL CONDITIONS Mogollon is in the southern part of Catron County, southwestern New Mexico. It lies near the western border of the Mogollon Range, 14 miles east of the Arizona line. Silver City, 80 miles to the southeast, is the nearest railroad point. The connecting road, over which supplies are hauled into camp by trucks, is an improved highway for about 50 miles; the remainder consists of graveled roads and unimproved steep mountain grades. One general supply truck and one tank truck make daily round trips. Hauling of supplies to the mine has cost at the rate of $0.08 per ton-mile; or, on the basis of ore production, $0.30 per ton mined. Lumber, hauled in from local mills, has cost an average of $30.00 per 1000 board feet, $8.50 of which has been for hauling. The annual consumption averages 108,000 board feet. Lime, hauled from a plant in Arizona, is about the only other item not brought out from Silver City. Fuel oil for the generation of power is the item of greatest hauling expense, the f.o.b. Mogollon cost of approximately $0.06 per gal. being nearly twice the f.o.b. refinery price. Water for power plant, mill and camp use flows to camp storage tanks through a 4-in. pipe line from a spring and intake 3 miles up Silver Creek Canyon. A few times, particularly in the month of June, mill operations have been suspended for two or three days because of water shortage. MINING CONDITIONS During the years 1938, 1939, 1940 and 1941, the mine produced 230,059 dry tons

Jan 1, 1943

By D. S. Nilsson

Small-scale mines are today expected to provide much of the increased production of metals and coal this county demands. But in fact the category of larger mines tends to grow in number and size faster than the category of smaller mines. Larger mines show the highest productivity, the lowest injury frequency, and the lowest costs. Lower cutoff grades can be wed in larger mines. The paper describes how the production level affects the choice between different types of loading, haulage, and hoisting equipment; how the increased production level in a mine results in lower production costs per ton; and how this affects the profitability of mining deposits with various ore grades. The future trend is expected to favor larger and larger operations.

Jan 1, 1983

By Adrian C. Dorenfeld

Concentradora "Doña Aida" (100 t /d capacity) was built in 1971-72 to treat dumps and ores containing mixed oxide-sulfide copper-gold-silver minerals derived from two veins. The veins, Don Felipe and Maria, are about 150 m apart, but are distinctly different mineralogically. The deposits are near Sun Juan de Guadalupe, Durango, Mexico. All new process equipment was manufactured locally, in or near Torreon, Coahuilu. Sampling, ore testing, flowsheet design, plant design, drawings, purchasing, financing, and construction, etc., were planned and directed by two engineers. Construction was executed by local miners and common labor (largely agricultural). The paper presents detailed costs for equipment and construction. The subsequent breaking-in operation is discussed.

Jan 1, 1982

By Forrest W. Kinsey

The use of pellets in North American blast furnaces has made the mixes used in the associated sinter plants unique. These mixes generally contain a high percentage of fine waste oxide materials as the principal iron bearing portion of the mix, with iron ores and concentrates added in minor amounts only. Additionally, the sinter basicity is always above one and can be three or higher. This paper will discuss the large body of knowledge and experience developed by one company on this type of sinter mix. Results of laboratory tests will be used to illustrate how mix composition and feed preparation affect sinter productivity and quality.

Jan 1, 1977

By Y. Zimmels, I. J. Lin, I. Yaniv

The potential application of magnetic and electric separation techniques in beneficiation of fine-particle feeds are reviewed. Special features of these techniques are considered and compared with a view to increased amenability of such feeds to separation in electro- magnetic fields. The following techniques are discussed, with reference to those already developed and in use to-date: - Differential-susceptibility separation (DSF). - High-gradient differential-dielectric separation (HGDDS). - High-gradient magneto-gravimetric separation (HGMGS). In this context the new approach - whereby selectivity of solid- solid separation processes, in wet high-gradient magnetic and electric separation, can be improved - is described, including experimental results from DSF and HGDDS tests.

Jan 1, 1980

Three years ago, when Sun Energy Development Co. (Sunedo) dedicated its Cordero mine in Wyoming, the company noted that its decision to venture into the coal industry was prompted by the need for domestic energy self-sufficiency. Now, as the energy situation assumes crisis proportions and the cry For coal intensifies, Sunedoo has begun a $21 million expansion program that will double the mine's productive capacity by the mid-1980s. When the Cordero come was originally conceived, Sunedoo obtained permission from permitting authorities to produce up to 11 million t/y (12 million stpy) of coal. But seeing opportunities in the coal market, Sunedoo returned to the agencies in 1976 and came away with permission to produce 22 million t/y (24 million stpy). Of that total permitted capacity, Cordero is expected to produce about 3.6 million tons (4 million st) this year.

Jan 9, 1979