Search Documents

By J. T. Eash, E. M. Wise

Many of the platinum metal alloys are hot-forged in the early stages of reduction from ingot and substantial quantities of platinum alloys are commercially employed at very high temperatures in ammonia oxidation units, orifices for forming glass rods and fibers and as cathodes in long-life thermionic amplifiers. They are used also for electrical heating resistors, safety blowout disks, thermocouples and crucibles. The tensile properties at elevated temperatures are important in many of these situations but data on the subject are limited. Creep data also are important, but will not be covered at this time. Scope and Conclusions Tensile tests were carried out at room temperature and elevated temperatures up to 1100" C. on previously well annealed samples of platinum. palladium and several of their important alloys with compositions shown in Table 1. The results are presented graphically in Figs. 1 to 4. The tensile strengths of platinum and the platinum-base alloys (with the exception of the 10 per cent rhodium-platinum alloy) at 1100" C. are from 16.6 to 18.8 per cent of the strengths of the same alloys (well annealed) at room temperature. The strength ratio of the 10 per cent rhodium-platinum alloy is 22.3 per cent, which is appreciably higher than that of the other materials tested. The tensile strengths of palladium and the palladium alloy at 1100" C. are from 10 to 11.2 per cent of the room-temperature values. The elongations of platinum and its alloys tend to increase at temperatures above 600" to 800" C., while the two samples of pure palladium show a maximum at 600" C.

Jan 1, 1938

By W. C. Thurber, C. J. McHargue

THE deformation textures of metals have been extensively studied because of both the practical implications in metal fabrication and the fundamental insight into the behavior of the metal during deformation. Most studies have been concerned with pure metals or solid-solution alloys and relatively little attention has been directed toward more complex alloy systems. Barrett' and Brick2 have summarized work on multiphase systems in terms of the relative ease of deformation of the phases. Thus, if the phases are deformed about equally, each develops its usual texture for the particular fabrication process. This behavior has been reported for Ag-Cu and Cd-Zn alloys3 and 62-38 brass.4 A dispersion of hard particles in a softer matrix interferes with the normal reorientation of the matrix lattice during deformation, thus distorting the texture or in some cases preventing its development. Increasing the amount of carbon in steel has been observed to increase the randomness of the ferrite5 and almost random textures have been reported for A1-12 pct Si eutectic alloy wires.6 It has also been noted that if the second phase is platelike, deformation causes the platelets to line up in a common direction. The present work concerns a quantitative study of the deformation textures in aluminum-uranium alloys containing 5 or 13 wt pct U. Alloys in this composition range are characterized by a pure aluminum matrix in which the intermetallic compound UA14, is dispersed. From a fundamental standpoint, this system affords the opportunity for studying the effects of a dispersed phase on texture development in an essentially pure metal matrix. Further, these alloys are commonly used as fuels for nuclear research and testing reactors, and a knowledge of the preferred orientation may be useful in evaluating physical and mechanical properties as well as response to fabrication. The deformation textures in sheets of aluminum (99.996 pct), Al-5 pct U alloy, and Al-13 pct U alloy were determined for reductions in thickness of 90 pct by cold rolling. The texture in an alloy rod of the latter composition which had been extruded at 455°C was also determined. It can be readily ascertained from the aluminum-uranium phase diagram that the 5 pct U alloy is hypoeutectic and contains 7.3 wt pct (3.4 vol. pct) UAl4. The 13 pct U alloy has the eutectic composition and contains 18.9 wt pct (9.4 vol. pct) UAl,; however, because of nonequilibrium solidification conditions, the typical eutectic microstructure was not developed. The alloys were prepared by open-air melting in graphite crucibles. The slab castings were cropped and cold reduced 90 pct in thickness on a two-high mill. The slabs were reversed after each pass. Although the uranium-bearing alloys exhibited edge cracking, they could be cold rolled to the desired thickness. Small coupons 1.5 by 0.75 by 0.1 in. thick were sheared from the center of the rolled plate with a major axis parallel to the rolling direction. To obtain a specimen of sufficient thickness for machining of the X-ray diffraction specimen, three coupons were laminated into a single three-ply sandwich with a suitable adhesive. Adhesives which could be cured at room temperatures were selected in order to prevent recrystallization during bonding. Bondmaster M-648 (Rubber and Asbestos Corp.) was used for the pure aluminum laminate and Armstrong A-6 (Armstrong Products Co.) was used for the alloys. The alloy for extrusion was cast in a cylindrical graphite mold! cropped and machined into a 3-in. diam by 4-in. long billet. This billet was preheated to 455°C, upset to 3.125 in. diam, and extruded on a 700-ton hydraulic press at a speed of 6 fpm through a flat-face, 1-in. diam die. The rod was quenched with a water spray as it emerged from the die. Pole-distribution data were obtained using the diffractometric method described by Jetter and Borie.7 A spherical X-ray diffraction specimen of

Jan 1, 1961

By J. T. Norton, Pekka Rautala

The phases and equilibria in the W-Co-C system have been studied by X-ray diffraction methods, metallographic technique, and thermal analysis. In addition to the 7 phase, two double carbides, called 8 and have been revealed. The compositions correspond to CO3 W6C2 and Co3-W10C4. The reactions leading to these phases have been explained and tentative diagrams of stable and metastable equilibria proposed. The basic reactions in sintering cobalt cemented tungsten carbides are discussed. THE W-Co-C system is of fundamental importance in practical carbide manufacturing as well as for the understanding of the sintering mechanism. Surprisingly little is known about this system, for the probable reason that all the important alloys are of two-phase structure and that the diagram Co-WC has been treated as a quasi-binary. This obviously is incorrect, because WC decomposes before melting. One ternary phase, 7, of composition Co3W3C has long been known. It was first studied by Adelskold, Sundelin, and Westgren,1 although the isomorphous iron-tungsten carbide was known earlier. There have been in the literature several reports of two 7 phases.' " Also the 7 phase has been considered unstable by Takeda4 and Westgren.1 The Co-WC diagram has been studied by Wyman and Kelley5 and a quasi-binary diagram has been published by Sandford and Trent.2 Takeda has published a tentative Co-W-C diagram, considering both metastable and stable equilibria. However, the lines of two-fold saturation are shown only partially and it seems impossible to complete the diagram without violating the phase theory. Therefore it seemed desirable to examine the system in more detail. Experimental Procedure The alloys used in the present investigation were made of powders of tungsten, tungsten monocarbide, cobalt, and carbon and were of the grade used in manufacture of commercial cemented carbides. The powders were ground and mixed in small stainless steel ball mills, using balls of the same material. Benzene was used as a dispersing agent. The mixing period was 1 hr, since this was shown to give suffi- ciently good mixing of the powders without too great a contamination from the mill. After ball milling, the specimens were pressed in cylindrical or rectangular dies. No paraffin or other lubricant was used and the small compacts had sufficient green strength to be handled without difficulty. Several sintering furnaces were employed. The most satisfactory arrangement was a vacuum furnace based on the Arsem principle which employed a graphite helix as the resistance heating element. Specimens were placed on graphite stands and there was generally a slight carburization or decarburiza-tion of the specimen surface, depending on the carbon content of the alloy. The evaporation of the cobalt at a sintering temperature of 1400°C was not significant, but became severe at 1500°C and higher. The sintering time was 1 hr at 2000°C and 2 to 4 hr at lower temperatures. It was not possible to quench the specimens, but the cooling rates were rather fast, greater than 300°C in the first minute. In the system under investigation, the reactions are sluggish, and it is believed that the high temperature structures are satisfactorily retained. The principal method of investigating the sintered specimens was X-ray diffraction by the Norelco recording spectrometer. Approximate determinations of the phase boundaries were made by the disappearing phase method. Ternary Phases To study the phase formation in W-Co-C system, a series of specimens was sintered at 1400°C. In this experiment two ternary phases, called here ? and k were formed in addition to the well-known 7 phase. The 7 phase, which has been completely described by Westgren: showed a range of homogeneity from 7 to 20 pct C and from 38 to 48 pct Co. At 1400°C the 7 phase was found to be in equilibrium with monotungsten carbide, 8, tungsten, 8, #?, and liquid. The boundaries toward #? and liquid were difficult to determine and appeared to be very temperature sensitive. The other boundaries are believed to be well fixed. The homogeneity range of 7, as measured in this work, is considerably smaller than the one

Jan 1, 1953

By Leroy W. Weeks, Peter B. Nalle

The rapid growth of the modern electronic computer industry during the past 15 years is, perhaps, the greatest phenomenon that has occurred in American business in this century. This growth is due in part to the new, and in some instances, revolutionary applications of computers instigated and developed by both the manufacturers of such equipment and their customers who search for easier, faster, more accurate methods of conducting their business operations. As in other industries, modern computers are becoming more common in the field of mining. The adaptation of computer analysis to the unique problems of mining companies is undergoing research and development by both electronic and mining companies. However, for those of us in mining who are interested in the possibilities of computer analysis and control, the basic question is Where can a computer system be of use in a mining operation today? Some ideas of such applications follow, as well as a specific example of computer control at the Riverside Cement Co.

Jan 9, 1960

By D. V. Carter, F. M. Hackbusch

Beginning the year 1938, the East and East Central Texas district comprised 48 counties, which is equivalent to the Texas Railroad Commission districts 5 and 6. At the close of the year there were 46 oil and gas fields in this district. Eight other fields, seven oil and one gas, have been abandoned. Exploratory Drilling During the year, 113 exploratory wells were drilled. Nine discoveries were made, five of which proved to be oil fields, three distillate, and one gas. Completions for the district were 2043 oil wells (distillate wells included), 36 gas wells and 163 dry holes. Exclusive of the East Texas field, the Marion County extension of the Rodessa field led the district in the number of completions during the year. Production and Proration All fields in the district produced a total of 182,369,484 bbl. of oil, a decrease of 12.57 per cent compared with the 208,594,453 bbl. produced during 1937. The East Texas field produced 148,189,913 bbl., which was 81.6 per cent of the district's production for 1938. November daily average oil production for the East and East Central district was 469,102 bbl. The estimated cumulative production to Jan. 1, 1939, for this district was 1,753,894,802 bbl. It is estimated that the East and East Central district produced 38.9 per cent of the state's total production for the year, which was 468,781,632 barrels. The decrease in 1938 production, as compared to that of 1937, in this district was partly due to the Saturday and Sunday shutdowns, 71 days for the year, which is equivalent to 19.45 per cent of the year. All fields in this district were affected by shutdowns except the Texas portion of the Rodessa field, which was shut in only during January and February. Certain wells were exempt from these shutdowns because of special pro-

Jan 1, 1939

By H. F. Moore

This paper gives a preliminary summary of results of tests on the resistance to fatigue under reversed stresses of steel subjected to cold-working and of tests to determine the effect of rest on the endurance of steel under reversed stresses. The tests of cold-worked steel were undertaken as part of an investigation by the National Research Council Committee on Fatigue Phenomena of Metals and were made by Mr. Moore; the tests to determine the effect of rest are part of an investigation now being made by Mr. Putnam. Both series of tests were made in the Materials Testing Laboratory of the University of Illinois. The preliminary results of these tests are reported now. because it is believed that test data on fatigue strength should be available at the earliest possible moment; however, it should be clearly kept in mind that this paper gives preliminary results and is intended to encourage discussion rather than to give final conclusions. Before giving the data of the tests, the writers will explain the term "fatigue strength" as used in this paper and will discuss briefly the method used in interpreting the test data of repeated-stress tests. The term fatigue strength, as applied to a material, may be defined as that maximum fiber stress that will cause fracture of the material after the repetition of any given number of cycles of stress, each cycle involving the variation of stress from a minimum to the above maximum. The fatigue strength, then, varies with the number of repetitions occurring in the lifetime of a structural or machine member and with the range of stress for each cycle of stress. The fatigue strength will be lower for a member in which the stress is completely reversed than for one in which the stress varies from zero to a maximum. In interpreting test data from fatigue tests under reversed stress, the stresses and corresponding numbers of repetitions required for failure are plotted on logarithmic cross-section paper. In 1910, Professor

Jan 2, 1919

By D. V. Carter, F. M. Hackbusch

Beginning the year 1938, the East and East Central Texas district comprised 48 counties, which is equivalent to the Texas Railroad Commission districts 5 and 6. At the close of the year there were 46 oil and gas fields in this district. Eight other fields, seven oil and one gas, have been abandoned. Exploratory Drilling During the year, 113 exploratory wells were drilled. Nine discoveries were made, five of which proved to be oil fields, three distillate, and one gas. Completions for the district were 2043 oil wells (distillate wells included), 36 gas wells and 163 dry holes. Exclusive of the East Texas field, the Marion County extension of the Rodessa field led the district in the number of completions during the year. Production and Proration All fields in the district produced a total of 182,369,484 bbl. of oil, a decrease of 12.57 per cent compared with the 208,594,453 bbl. produced during 1937. The East Texas field produced 148,189,913 bbl., which was 81.6 per cent of the district's production for 1938. November daily average oil production for the East and East Central district was 469,102 bbl. The estimated cumulative production to Jan. 1, 1939, for this district was 1,753,894,802 bbl. It is estimated that the East and East Central district produced 38.9 per cent of the state's total production for the year, which was 468,781,632 barrels. The decrease in 1938 production, as compared to that of 1937, in this district was partly due to the Saturday and Sunday shutdowns, 71 days for the year, which is equivalent to 19.45 per cent of the year. All fields in this district were affected by shutdowns except the Texas portion of the Rodessa field, which was shut in only during January and February. Certain wells were exempt from these shutdowns because of special pro-

Jan 1, 1939

By Morris Cohen

WITHIN the past two years, a number of publications have called attention to the double peaks, or stages, that appear in the hardness and strength curves of certain aging alloys. The author has shown the existence of double hardness peaks during the aging of a high-purity silver-copper alloy;1 and on the basis of electrical resistance, microscopic, dilation and lattice-parameter measurements, he concluded that the initial hardness peak occurs prior to precipitation while the secondary hardening is due to precipitation. It was suggested that the general mechanism of age-hardening involves two consecutive processes, the first consisting of nucleus or knot2 formation, and the second consisting of actual precipitation and particle growth. It was further held that the two stages are interdependent, but because of nonuniform precipitation they may overlap each other to an extent that increases as the aging temperature is raised. At high aging temperatures, the effect of the first stage cannot be detected because of the rapid occurrence of precipitation. The general theory of age-hardening recently presented by Dr. M. L. V. Gayler3 is in close agreement with the picture outlined above. With reference to work done on duralumin, copper-beryllium and copper-silver alloys, Dr. Gayler also concluded that age-hardening takes place in two consecutive steps: first, diffusion (in which the solute atoms migrate to certain crystallographic planes), and then precipitation. However, W. L. Fink and D. W. Smith4 have shown that the double aging peaks that appear in the strength curves of high-purity aluminum-copper alloys may be explained without recourse to pre-precipitation phenomena. By means of very careful metallographic technique, Fink and Smith demonstrated that during aging the precipitation takes place at an accelerated rate along the grain boundaries and slip planes as a result of the plastic deformation caused by the drastic quench from the solution heat-treatment temperature. ? The general precipitation occurs at a

Jan 1, 1938

By J. Jay Jacobsen

A dynamic regional coal development model is constructed for the Eastern Powder River Basin of Wyoming. Using this model, alternative development schedules from a recent environmental impact statement submitted to the Department of the Interior are simulated (Ref. 1). These alternatives include different mixes of export capacity, different coal conversion techniques within the region, as well as various levels of coal production. Exportation of 70 to 80 percent of an ultimate coal production of 180 million tons (163.3 x l09 kg) per year and the careful phasing of additional public services with population growth effectively reduce the social and environmental impacts of coal development. The alternative involving the addition of 43,000 megawatts of electrical generation capacity has very significant adverse social and environmental impacts on the region.

Jan 1, 1977

By John F. Havard, Armine F. Banfield

Sooner or later, we all get involved in the economic study and valuation of a mineral deposit. To communicate clearly the necessary information, we must scrupulously use various terms with specific meaning. All these terms-such as ore, exploration, development, production, reserves, proven ore, probable ore, possible reserves, resources, as well as similar terms applying to coal-are continually on the lips of anyone who reports on the economic aspects of a mineral deposit at the exploration, development, and production stages. The meaning of these terms is even more important in feasibility studies to determine whether a deposit should be put into production. Finally, careless use of these terms in reports published for public financing may, and sometimes does, lead to prosecution of the writer for misleading information.

Jan 7, 1975

By D. E. Wolfson, D. A. Reynolds, F. W. Smith

IN 1948 the U. S. Bureau of Mines began a three- phase program to evaluate the extent and quality of U. S. coking coal: 1) a factual appraisal of known recoverable reserves in beds of mineable thickness, 2) a study of preparation characteristics, and 3) a study of carbonization properties. A previous paper presented the methods used in assessing reserves.' Although this investigation is only partly completed, data on coking properties of the Pittsburgh district coals are now available. The results are presented in this article. When coals are selected for manufacture of metallurgical coke more factors must be considered than for any other major use, as no basic industry requires coal of such high quality and uniformity. This is particularly true in the Pittsburgh district, where blast furnace practice is based on use of cokes from high quality coals. Although it is true that inferior coals are carbonized in other industrial areas, both here and abroad, the Pittsburgh coals are the best economically obtainable in the required tonnages, even though they are not the most desirable for metallurgical use.

Jan 3, 1957

By J. B. Hiskey, W. J. Schlitt, W. G. Pitt

Aqueous SO2 (sulfurous acid) is an interesting chemical compound. It functions as a reagent in various hydrometallurgical systems, but also represents an undesirable constituent in gyro- and hydrometallurgical effluent solutions. When present in such streams, SO2 can be oxidized to the more stable sulfate form to avoid exsolution of SO2 as a source of fugitive emissions and to simplify standard water treatment plant operation. This study provides information on the stoichiometry, kinetics, and mechanism of SO2 oxidation using oxygen and an iron salt catalyst with solutions containing 0.05-20 g/L (0.002-0.7 oz per gal) SO2. The effects of iron salt concentration, oxygen pressure, temperature, degree of agitation, and pH on SO2 oxidation are also described.

Jan 1, 1984

By M. Hansen, C. C. Wang

THE 6 phase of the Cu-Sn system (Cu,Sn, = 32.53 pct Sn) was considered to be stable down to room temperature until Owen and Iball showed by X-ray analysis that it undergoes a eutectoid decomposition into the a and e phases at a temperature near 300°C. Their findings have been confirmed by other investigators,2-5 a11 of whom used X-ray diffraction studies of powdered specimens. The transformation temperature has been reported by various authors as lying between 300" and 380°C. To our knowledge, no microscopic evidence of the eutectoid reaction has been published, as yet. It was in connection with other work that longtime annealings at 300°C were conducted with alloys containing 22, 32.6, and 35 pct Sn (nominal compositions) prepared from electrolytic copper and electrolytic tin and cast in a small iron mold. The specimens were first annealed at 700°C for 5½ hr and quenched from 400 °C after cooling to, and annealing at, that temperature for 9½ hr. After this treatment the sample with 22 pct Sn was cold worked for 15 pct reduction in thickness; the 32.6 and 35 pct alloys were too brittle to be cold worked. The final anneal at 300°C was done in a sealed pyrex glass bulb for 63 days. Fig. 1 represents the microstructure of the annealed alloy with 22 pct Sn. It shows primary a solid-solution crystals in a matrix of the (a + 8)-eutectoid formed at 520 °C. The a crystals contain 8 inclusions which precipitated from a due to the decrease in the solubility of tin in copper with fall in temperature. The decomposition of the 8 phase into a (light) and E (dark) can clearly be seen in some areas of the (a + 8)-eutectoid matrix. However, the decomposition is far from being completed, even after the long-time anneal used. Figs. 2 and 3 depict the microstructures of the annealed 32.6 pct alloy, which was intended to consist entirely of 6 phase. Due to some loss in copper on melting, the composition is slightly higher in tin. Accordingly, the sample after quenching from 400 "C consisted of grains of the 8 phase with the e phase arranged along the grain boundaries and as a Wid-manstatten precipitate within the 6 grains. After an annealing time of 63 days, the eutectoid decomposition, 6 + a + e, is still in its early, initial state. The pearlitic type of eutectoid is nucleated at the c crystals, preferably those surrounding the grain boundaries of the 8 phase. The appearance of the (a + €)-eutectoid in the 35 pct Sn alloy was very similar to that shown in Figs. 2 and 3. Again, the eutectoid decomposition nucleated at the 6 phase and proceeded from there into the 8 areas. As is evident from Fig. 2, the rate of decomposition of the 6 phase at 300°C is extremely sluggish: In the representative area shown only about 5 pct of the 8 phase has undergone the eutectoid trans- formation after annealing for 63 days. On the other hand, Owen and Williams2 have reported that X-ray photographs of powdered samples with between 17.5 and 34 pct Sn did not show 8 lines after annealing for only five to seven days at 300°C. This is in accordance with the fact that the rate of reaction in powdered samples is higher than in massive specimens, as a result of the excess free energy of the powder (due to its greater surface area). The authors wish to express their thanks to C. A. Johnson for preparation of the micrographs.

Jan 1, 1952

By E. H. Crabtree, V. W. Winters, T. G. Chapman

IN 1939 one of the authors* described advances in carbon-cyanidation for the period 1932 to 1939 • T. G. Chapman: A Cyanide Process Based on the Simultaneous Dissolution and Adsorption of Gold. Trans. AIME (1939) 134, 207. and included: (1) the dissolution of gold in an ore pulp by cyanide and its simultaneous adsorption by carbon, (2) the stage addition of adsorptive carbon and its movement countercurrent to the flow of the ore pulp, and (3) the recycling of adsorptive carbon. Considerable additional experimental and pilot plant work have been done by the authors since 1939 and the results of such work E. H. CRABTREE, JR., Member AIME, is Director of Milling, Eagle-Picher Mining and Smelting Co., Miami, Okla., V. W. WINTERS is Superintendent, Sahuarita Concentrator, Eagle-Picher Mining and Smelting Co., Tucson, Ariz., and T. G. CHAPMAN, Member AIME, is Dean, College of Mines, University of Arizona, Tucson. AIME Sun Francisco Meeting, February 1949. TP 2744 B. Discussion (2 copies) may be sent to Transactions AIME before March 31, 1950. Manuscript received March 3, 1949. have been sufficiently encouraging to justify a second paper. Developments from 1939 to 1948: In 1941, Verne W. Winters did the first experimental work in eliminating agitation during dissolution and adsorption and thereby demonstrated that the dissolution of gold by cyanide and its simultaneous adsorption by carbon take place essentially to completion in a stagnant pulp. Shortly thereafter, and as a result of the stagnant pulp experimental work, Winters and Chapman demonstrated that soluble gold, in a cyanide ore pulp, would migrate from the ore pulp through a perforated container and be adsorbed by carbon within the container. During the same year, the Eagle-Picher Mining and Smelting Co. erected a 25-ton capacity pilot plant at the Harquahala mine about 9 miles from Salome, Ariz. Experimental work at this plant comprised chiefly the stagnant pulp modification of carbon-cyanidation although considerable work was done in the grinding and activation of carbon, and testing various methods of extracting adsorbed gold from carbon. Soon after the completion of the Harquahala

Jan 1, 1951

By E. H. Crabtree, T. G. Chapman, V. W. Winters

IN 1939 one of the authors* described advances in carbon-cyanidation for the period 1932 to 1939 • T. G. Chapman: A Cyanide Process Based on the Simultaneous Dissolution and Adsorption of Gold. Trans. AIME (1939) 134, 207. and included: (1) the dissolution of gold in an ore pulp by cyanide and its simultaneous adsorption by carbon, (2) the stage addition of adsorptive carbon and its movement countercurrent to the flow of the ore pulp, and (3) the recycling of adsorptive carbon. Considerable additional experimental and pilot plant work have been done by the authors since 1939 and the results of such work E. H. CRABTREE, JR., Member AIME, is Director of Milling, Eagle-Picher Mining and Smelting Co., Miami, Okla., V. W. WINTERS is Superintendent, Sahuarita Concentrator, Eagle-Picher Mining and Smelting Co., Tucson, Ariz., and T. G. CHAPMAN, Member AIME, is Dean, College of Mines, University of Arizona, Tucson. AIME Sun Francisco Meeting, February 1949. TP 2744 B. Discussion (2 copies) may be sent to Transactions AIME before March 31, 1950. Manuscript received March 3, 1949. have been sufficiently encouraging to justify a second paper. Developments from 1939 to 1948: In 1941, Verne W. Winters did the first experimental work in eliminating agitation during dissolution and adsorption and thereby demonstrated that the dissolution of gold by cyanide and its simultaneous adsorption by carbon take place essentially to completion in a stagnant pulp. Shortly thereafter, and as a result of the stagnant pulp experimental work, Winters and Chapman demonstrated that soluble gold, in a cyanide ore pulp, would migrate from the ore pulp through a perforated container and be adsorbed by carbon within the container. During the same year, the Eagle-Picher Mining and Smelting Co. erected a 25-ton capacity pilot plant at the Harquahala mine about 9 miles from Salome, Ariz. Experimental work at this plant comprised chiefly the stagnant pulp modification of carbon-cyanidation although considerable work was done in the grinding and activation of carbon, and testing various methods of extracting adsorbed gold from carbon. Soon after the completion of the Harquahala

Jan 1, 1951

By A. W. Gauger

Fox perhaps one hundred years scientists have been engaged in attempts at devising a satisfactory method of classification of coal. During this time many charts, tables and graphs have been proposed, some of which have had considerable merit, but no one system has been found to be applicable to all ranks of coal, nor has any one system received general acceptance. In many of the proposals, water eliminated between room temperature and 105° C. has been regarded as extraneous matter and calculations have been made to the air-dry or water-free basis. Such methods of. calculation do not lend themselves to satisfactory grouping of the high-moisture coals.1,2 A consideration not only of the properties of the high-moisture coals and their behavior on drying but of the generally accepted ideas of the coalification process and the role of water in this process indicates that water is an essential constituent of all coals and therefore should not be neglected. For example, in such low-rank coals as the lignites of the Northern Great Plains' deposits the inherent moisture of the lignite as mined plays a very important part in the physical properties thereof. Freshly mined lignite contains upwards of 30 per cent water and is extremely tough and resistant to shock. Upon exposure to the atmosphere, the lump loses part of its moisture and checks and splits, leaving a friable and broken up residue. So far as we have been able to determine, water is the only thing lost in this process and we are forced to the conclusion that moisture plays an extremely important part in the structural properties of the original lignite. With reference to the coalification process, Mack and Hulett3 pointed out in 1917 the important part that water played therein. They observed that water cannot be removed from peat or coal by pressure alone, but only as the result of chemical reaction, and suggested that peat in its early stages may be largely a hydrosol. Slow chemical changes occur over a long period of time until finally the mass becomes more largely a hydrogel. These views are substantiated to some extent by the experi-

Jan 1, 1932

By E. Martinez, M. L. Hollander

Sulfurization of copper oxides was investigated using differential thermal analysis (DTA) and thermal gravimetric analysis (TGA). When mixtures of cuprous oxide and sulfur were heated, the surface of the cuprous oxide was converted to cupric sulfide at the melting point of sulfur (119°C); additional sulfuriza-tion took place when the sulfur vaporized above 200°C. Cupric oxide also reacted with sulfur to form cupric sulfide but the starting temperature was approximtely 225°C. When the cupric oxide and sulfur were physically separated, sulfurization still occurred indicating a reaction with the vapor phase of sulfur. Sulfurization was obtained in runs with cuprite, chrysocolla and basic copper carbonate. Further decomposition of cupric to cuprous sulfide was noted at somewhat higher temperatures. The DTA-TGA data made it possible to set up postulated reactions in each system. These techniques were found to be well suited for studies of this type. Because of the difficulty encountered in flotation of many metallic oxide minerals, efforts have been made to find suitable reagent combinations to sulfi-dize these minerals in the flotation circuit. Recently Bautista and Sollenberger,1 using a different approach, showed that the surfaces of many oxide minerals can be converted to sulfides by heating them with sulfur to temperatures between 150° and 225°C. This technique was effective even with chrysocolla, a mineral which is very difficult to sulfidize. The primary objective of the present study was to obtain information on the reactions between the oxide minerals and suIfur. A better understanding of the mechanisms involved might prove useful in pointing the way to improvements in the process. A secondary objective was to demonstrate the value of thermo-analysis in investigations of this type. Bollin and Kerr2 have reported the use of a modification of differential thermal analysis to study the thermal reactions which occur on heating elemental constituents in a closed system to synthesize copper sulfides and iron sulfides. Differential thermal analysis (DTA) was used to detect enthalpic changes as mixtures of minerals and sulfur were heated. The DTA indicated the temperatures at which reactions started and whether they were exothermic or endothermic. Weight change data were obtained by thermal gravimetric analysis (TGA). These data could often be used to support postulated reactions and to eliminate consideration of other possible reactions. EQUlPMENT Differential thermal analysis (DTA) involves measuring the temperature difference between the sample being tested and a thermally inert reference, generally aluminum oxide, as both are heated at a uniform rate. Series connected thermocouples in the sample and reference are used to detect the temperature differences that occur as the sample undergoes enthalpic changes.3 Crystalline transitions, fusions, vaporizations, dehydrations, decompositions and many solid state reactions can be detected. A DTA unit manufactured by the Robert L. Stone Co., Austin, Tex., was used in this investigation with a temperature rate increase of 10°C per min. The samples and reference were placed in Inconel cups with wells in the bottom into which the differential thermocouples fit, and run in a nitrogen atmosphere. Thermal gravimetric analysis (TGA) measures the changes in weight that a sample undergoes as it is heated. A Chevenard thermobalance converted electronically for graphic recording was used with a heating rate of 5°C per minute. An X-Y recorder plotted temperature on the X axis and weight changes on the Y axis. A flow of 250 ml per min of nitrogen was streamed through the furnace. Samples were placed in a porcelain crucible open at the top, unless otherwise noted. EXPERIMENTAL RESULTS Sulfur: Two sulfur samples from different sources were tested. The DTA of a high purity sulfur and a reagent grade sublimed sulfur are shown in Fig. 1. Nearly all the tests were run with the sublimed sulfur due to the difficulty in grinding and high electrostatic charge encountered with the high purity sample. Sulfur undergoes three endothermal reactions below 200°C. The first is a solid-solid crystalline transi-

Jan 1, 1964

By J. Kent Smith

Vanadium is generally spoken of as a rare element; but, even in the light of our resources as known a couple of years ago, this description could be accepted in a qualified sense only. In fact, vanadium is very widely distributed, being a constituent of most clays, while even caustic soda has been shown to contain almost regularly a minute proportion of it, although the quantity in each case is so small as to render impracticable the extraction of the metal therefrom with profit. The opening-up of a large deposit of vanadium sulphide ore in South America has put a new phase on the commercial outlook of vanadium, the technical value of which for the improrement of steel has been proved by rigorous scientific investigation. This sulphide ore has the following analysis: Per Cent. Vanadium sulphide,.39.84 Molybdenum sulphide,.1.57 Nickel sulphide,.........1.49 Iron sulphide,.........4.07 Arsenic sulphide,.. nil. Copper sulphide,.. nil. Manganese sulphide,..nil. Free sulphur,..30.57 Phosphorus,...nil. Silica,....13.60 Alumina,..........2.46 Combined water, 5.00 Carbonic acid, Lime, magnesia, potash, soda and unaccounted for, 100.00 Being a free-burning ore it is calcined with ease, losing 45 per cent. of its weight in the process. The calcined ore has the following analysis:

Jan 1, 1908

By E. Stansfield

IT. has long been known that coal is unstable and oxidizes in air, even at ordinary atmospheric temperatures; also, that such oxidation affects the analysis of coal. Nevertheless little or no precaution is taken to prevent oxidation in the ordinary methods of analysis, and the possibility of error due to oxidation is sometimes ignored even in researches on coal. Although the general nature of coal oxidation is well known, and many workers have made careful studies of the rate of oxidation of different types of coal exposed to oxygen at different temperatures, yet the amount of oxidation coals undergo in the ordinary process of analysis, and its influence on the determined analysis, is not well known, and the published data are widely scattered through the literature. This paper is a collec-tion, from this laboratory, of data that bear on the subject, together with a brief summary of three methods employed here to evaluate the oxidizabil-ity of coal. The post-Carboniferous coals of Alberta range all the way from anthracite down to lignite. As some of them are notably susceptible to oxidation, the necessity for care was early forced upon our attention, and oxidation has been reduced either by the removal of air with a vacuum pump or by the displacement of air with natural gas (methane). The two routine analytical operations most liable to involve oxidation are the preliminary, partial drying of the crushed coal (called air-drying) and the determination of moisture. The first is a prolonged operation on coarse coal at ordinary temperatures, and the second a short treatment on powdered coal at higher temperatures. Oxidation also occurs in coal samples stored in ordinary sample bottles. In order to gain information for this study, determinations were recently carried out on the same samples in air, in natural gas, and in vacuo. Sixteen coals were tested; three would be classed in the United States as coking bituminous coals, two as noncoking, nonslacking, bituminous coals, and the rest as subbituminous. Table 1 gives typical analyses of these coals as mined.

Jan 1, 1934

By L. Douglass Anderson

For some years past the annual reviews of the metallurgy of lead have almost uniformly stated that there have been no great changes, such as there were being more particularly noticeable in the refinement of details. While this is quite true, nevertheless these changes in details are gradually bringing about a condition that, taken as a whole, constitutes a considerable advance in the art. Local circumstances have often compelled metallurgists to adopt certain peculiarities of practice which upon trial have been found advantageously applicable to more than the restricted district of origin. This paper will deal with some of the more novel features developed in recent years at the United States smelter, Midvale, Utah, particularly with reference to the influence of the bag house. The plant is equipped with six blast furnaces, 48 by 160 in., mechanically fed; four Wedge furnaces for roasting matte and sulphide ores; four Dwight-Lloyd sintering machines; 20 converter boxes for blast roasting; storage bins for ore, fuel, and fluxes; "oxide" and "sulphide" sampling mills; bag house taking all the gases of the plant; arsenic plant for treating the dust gathered there; laboratory, shops, etc. The most marked feature of the plant is its complete bag-house system. Of the many schemes thus far tried for preventing damage to surrounding agricultural interests the writer is aware of none as yet quite as efficient as the bag house. A common remark of visitors upon approaching the plant and viewing the clear stacks is that it appears to be shut down, whereas once inside all the evidences of industry are found. Bag-housing blast-furnace gases presents no peculiar difficulties. The gases from properly run furnaces are comparatively cool, contain scarcely a trace of acid and do not burn the filtering medium. All that is required is a proper mechanical design of the bag house and its accessories, the provision of ample filtering area, and of convenient means for handling and treating the product. While cotton or duck bags have been used, on the whole woolen bags woven of the raw wool appear to give sufficiently longer life to warrant their heavier expense. As for the filtering

Jan 1, 1915