Search Documents

By R. B. Sosman, J. C. Hostetter

We have shown in the preceding paper that practically all natural oxides of iron contain a determinable percentage of ferrous iron, and in many cases the percentage approaches that in magnetite itself. Some of these oxides are true homogeneous solid solutions. Others are not homogeneous, and can be separated magnetically into fractions. The nature and cause of this inhomogeneity in certain special cases form the subject of the present paper. Magnetic FRactionation of Oxides of Iron The magnetic fractionation of a sample of oxide can be conveniently carried out by powdering the material very fine, and exposing it at various distances from the poles of an electromagnet. The magnet that we used was specially designed1 to give a strong field together with a steep gradient outside of the poles. It is set in a frame, with the pole pieces directed downward. A glass plate can bc adjusted at various distances beneath the poles. If the fine iron oxide powder is placed just beneath the glass plate, successive portions of the powder are picked up by the magnetic attraction and are caught against the glass plate, the most magnetic portions being taken up at the greatest distance from the poles. Some natural oxides can thus be separated into several fractions of different magnetic susceptibilities. Among other natural iron oxides, we examined the powder obtained by crushing some crystals of hematite from Elba.2 We found that

Jan 1, 1918

By G. T. Brookman, P. B. Katz, D. K. Martin, J. A. Ripp

With the increasing emphasis on using American fossil fuel resources, more facilities are evaluating coal conversion. In addition, those facilities now using coal are considering better coal storage procedures to minimize negative environmental impacts. For example, rainfall and snowmelt on a coal pile produce a drainage stream high in acidity, suspended and dissolved solids, iron, sulfate, and trace metals. Usually, the characteristics of the runoff stream do not allow for direct discharge to streams and lakes. Detention in a holding pond and pH adjustment are traditional methods of treating coal pile runoff before discharge. Historically, this treatment methodology has been performed inefficiently without a good data base to assess how much runoff treatment is needed to meet effluent guidelines. A model was developed to simulate runoff volume and pollutant loadings under different rainfall conditions. This model will be used to size and design treatment works for coal pile drainage. The Ohio State University (OSU) version of the Stanford watershed model was selected as the base model. The OSU model simulates overland runoff in a rural area. It includes factors such as soil moisture, depression storage, infiltration, and flow to a ground water reservoir. TRC also used the OSU co-model for acid production in coal refuse piles as the basis for qualitative modeling work. A number of modifications were made to the OSU models to make them applicable to coal storage piles. The physical/chemical reactions included in the models are described in more detail in the project report. In addition, the models were altered so that a standard NOAA magnetic tape of historical meteorological data can be used as data input instead of requiring the user to create a data file. The resulting TRC coal pile drainage model is actually two models - a quantitative model, termed H2OTRC, and a qualitative model, TRCCOAL.

Jan 1, 1984

By William Kranz

THE increased service demands on some of the products of the National Malleable Castings Co. prompted it about eight years ago to investigate the electric furnace, both in America and in Europe. The process bad' already been sufficiently developed in Europe to lead us to believe that the electric furnace would most nearly meet our requirements. After further investigation and consultation with the highest authorities on the subject, we decided upon the Heroult type as the simplest and most practicable. In 1910, we built a furnace of this type, of 300 lb. capacity, for experimental purposes, and although it was crudely constructed the quality of the material we were able to make justified the installation of a 6-ton Heroult furnace in 1912. This furnace has three electrodes, 17 in. in diameter, uses three-phase, 60-cycle current, and is equipped with Thury regulators, which give us good regulation and a uniform load on the line even when cold melting. The power factor of the furnace is 94 per cent. Since July, 1912, the furnace has been in continuous operation, producing up to the present time, over 20,000 tons of both carbon and alloy steels of varying analyses and of exceptional quality. Both cold-and hot-metal charges have been used, with a power consumption of about 150 kw-hr. per ton in the case of hot-metal charges and from 500 to 600 kw-hr. per ton in the case of cold charges. The electric energy consumed varies according to the final analysis of the steel and the amount of refining required. Too much cannot be said about the refining possibilities of the electric furnace, for no other method of steel manufacture can compete with the electric in this respect.

Jan 5, 1915

By W. M. Rust, W. D, D. W. Mounce

The almost universal acceptance of electrical logging by the petroleum industry calls for a critical examination of the physical bases of the common methods. This is particularly needed for the natural potential log. The conventional explanations are based on the phenomena of electrofiltration and electro-osmosis. However, experimental data show that they fail to give a basis that is quantitatively sound. Moreover, they lead to interpretations of details of electrical logs that are erroneous. It was found experimentally that when a plug of shale is placed in a chain of dissimilar electrolytes, a current flow results. Experiments on oil-well cores and fluids similar to those existing in wells show that potentials are set up which are in reasonable agreement with those encountered in electrical logging. Doubtless other sources of potential are important but this explanation not only accounts for much of the potential but also clarifies some fairly familiar examples of misinterpretations. Introduction The extraordinary value of electrical well logging as a tool for petroleum engineers and geologists is now so uni- versally recognized that it is not necessary to point out the ways in which it can be useful. It is sufficient to mention only the saving that has resulted from the elimination of much coring that would have been necessary under former practices and the considerable additions to reserves resulting from the discovery of sands missed in coring. Paradoxically, the very remarkable success that has resulted from the application of electrical logging to correlation and completion problems has cost some of its most consistent users dearly.' The fact that some operators have placed unwarranted faith in erroneous interpretations of electrical logs does not reduce the value of the logs. It should, however, make one pause long enough to ask why experienced users should be misled. The answer to this question is not hard to find. In nearly every case, the fault has been oversimplification. This is illustrated very aptly by the familiar interpretation and theory of the natural potential log. Recording and Interpreting Logs The natural potential log is extremely simple to record precisely enough for all present-day uses. One needs only an electrode, a cable to lower the electrode through the drilling mud, a recording meter and a surface ground connection. The electrode can be elaborate but need not be. A simple brass rod 2 in, in diameter and 2 or 3 in. long is quite satisfactory. The cable need not be particularly well insulated, nor need it have a very low resistance. The recorder can be a vacuum-tube 1 References are at the end of the paper.

Jan 1, 1944

Book Review Mexico, TODAY AND Tomorrow. By E. D. Trowbridge, Detroit. The McMillan Co., New York, 1919, 353 pp., 7;2 X 5 in. $2.00. The first eight chapters are devoted to an historical narrative of the Mexican peoples from the earliest times to the close of the war with the United States in 1345. "In dealing with events antedating what may be termed modern Mexico" the author has "made no attempt at original research, and so far as concerns anything prior to 1900, the work here presented is a repetition, a reflection, of the findings of opinions of Fiske, Prescott, Bancroft, Luis Perez Verdia and other authorities." The remainder of the hook deals with Mexico during and since the Diaz regime. It is interesting throughout but is not always convincing or consistent. Social conditions are described in a way illuminating and possible only to one who is familiar with the peon and his hitherto seemingly hopeless position in reference to the wage system and church oppression. In fact, the author makes the hold accusation that the "primitive rather than immoral" condition of the peons in the matter of their marital relations is due to the disregard of the church for their welfare and capabilities. The true accounts of the Madero revolution and the Huerta regime read like fascinating medieval fiction. The reason given for men remaining in the Madero army is still the controlling one regarding any of the armies there. "They had horses, arms, all the food they wanted, money to spend and no work." The discussion of Mexican financial schemes is wholly from the Carranza viewpoint. To meet a monthly deficit of ten million pesos the author says "the government forced loans from the National Bank, and Bank of London and Mexico, and repeated the operation several times, finally practically exhausting their bullion and cash reserves. Hostile foreigners refer to this operation as the looting of the hanks! Drastic as this action was, there was good ground on which to justify it." However, that necessity knows no law is never an acceptable tenet except to him who applies the screws. The discussion of the economic problems and their solution is rather chimerical and presupposes a civil and national virtue in the present government not discernible except to one ultra friendly. The book is an interesting exposition of the very much involved situation from the viewpoint of approval of both the Carranza government and the attitude of the United States in its dealings with him. The editing of the book leaves something to he desired. P. E. B.

Jan 9, 1919

By W. D, D. W. Mounce, W. M. Rust

The almost universal acceptance of electrical logging by the petroleum industry calls for a critical examination of the physical bases of the common methods. This is particularly needed for the natural potential log. The conventional explanations are based on the phenomena of electrofiltration and electro-osmosis. However, experimental data show that they fail to give a basis that is quantitatively sound. Moreover, they lead to interpretations of details of electrical logs that are erroneous. It was found experimentally that when a plug of shale is placed in a chain of dissimilar electrolytes, a current flow results. Experiments on oil-well cores and fluids similar to those existing in wells show that potentials are set up which are in reasonable agreement with those encountered in electrical logging. Doubtless other sources of potential are important but this explanation not only accounts for much of the potential but also clarifies some fairly familiar examples of misinterpretations. Introduction The extraordinary value of electrical well logging as a tool for petroleum engineers and geologists is now so uni- versally recognized that it is not necessary to point out the ways in which it can be useful. It is sufficient to mention only the saving that has resulted from the elimination of much coring that would have been necessary under former practices and the considerable additions to reserves resulting from the discovery of sands missed in coring. Paradoxically, the very remarkable success that has resulted from the application of electrical logging to correlation and completion problems has cost some of its most consistent users dearly.' The fact that some operators have placed unwarranted faith in erroneous interpretations of electrical logs does not reduce the value of the logs. It should, however, make one pause long enough to ask why experienced users should be misled. The answer to this question is not hard to find. In nearly every case, the fault has been oversimplification. This is illustrated very aptly by the familiar interpretation and theory of the natural potential log. Recording and Interpreting Logs The natural potential log is extremely simple to record precisely enough for all present-day uses. One needs only an electrode, a cable to lower the electrode through the drilling mud, a recording meter and a surface ground connection. The electrode can be elaborate but need not be. A simple brass rod 2 in, in diameter and 2 or 3 in. long is quite satisfactory. The cable need not be particularly well insulated, nor need it have a very low resistance. The recorder can be a vacuum-tube 1 References are at the end of the paper.

Jan 1, 1944

By R. A. Bergman, C. J. B. Fincham

THERMODYNAMIC properties of many high-temperature systems containing sulfur, such as slags, metal sulfides, and solutions of sulfur in liquid metals, have been studied by means of equilibration with known gas mixtures.'" This method presupposes a complete and accurate knowledge of the thermodynamic data for all possible components of the gas phase at high temperatures. However, a survey of the data available up to 1952 on the thermodynamics of gaseous sulfur species and compounds, by Richardson and Jeffes,' showed that there was considerable uncertainty in the values of the free energies of formation of S, SO, HS, and CS. In many cases, this uncertainty made it impossible to decide whether or not these species would form a significant proportion of the sulfur present in the gas phase in any given system. After the review by Richardson and Jeffes had been published, St. Pierre and Chipman6 measured, by an indirect method, the free energy of formation of SO. This also enabled a clear choice to be made among the three possible spectroscopic values for the dissociation energy of S2 into atoms10 thereby determining the free energy of formation of S from S2, and fixing the free energy of formation of HS more accurately" The main purpose of the present investigation was to measure the free energy of formation of CS, which was still in considerable doubt. For example, at 1600°C, it could be estimated to be +6 +25 kcal per mole,* most of the uncertainty being in the * Based on the dissociation energles of CS6 and S2,5 the heat of sublimation of graphite, and, the assumption that the entropy of formation of CS is the same as that of CO. value of the dissociation energy." A secondary purpose of the investigation was to determine more accurately the equilibrium sulfur pressures over dilute solutions of sulfur in carbon-saturated liquid iron. General Method Dilute solutions of sulfur in liquid iron, saturated with carbon, were brought to equilibrium at 1600" and 1800°C, with known gas mixtures consisting, initially, of A and CS2. After equilibrium had been reached, the melts were quenched and analyzed for sulfur. In the high temperature region of the furnace, an equilibrium was set up between the various possible sulfur species and compounds in the gas phase; namely, CS2, CS, S2, and S. (It can be calculated that the amounts of S6 and S, are negligible at these temperatures:) Morris and Bueh17 and Kitchener, Bockris, and Libermana had previously studied the corresponding

Jan 1, 1958

By S. R. B. Cooke, H. S. Choi, D. H. Harraway, I. Iwasaki

The mineralogy of natural iron ore samples and their slimes have been investigated and the nature of slime interference in iron ore flotation has been studied. The results have been correlated with the flotation behavior of a natural ore sample. Various conclusions have been reached as a result of these studies. In the flotation of iron oxide ores, desliming is generally considered to be an essential step to successful separation, irrespective of whether the iron oxide or siliceous gangue minerals are to be floated, although some workers have found empirically that certain collectors and reagent combinations are less sensitive to the presence of slime than others. The detrimental effect of slime is considered to be twofold. First, the presence of slime presupposes a high reagent consumption because of high specific surface. When clays are present and when cationic collectors are used abstraction by ionic exchange may augment this condition. Attempts to compensate by the addition of large amounts of reagent result in only partial correction. Second, slime coatings on granular particles tend to interfere with the bubble-mineral contact. The nature of slime coatings in flotation is quite complex and has been the subject of considerable study; an attempt was recently made by Fuerstenau et al.' to relate the slime-coating density with flotation recovery and with the properties of the electrical double layer at the mineral surfaces. Although major constituent minerals in the oxidized iron ores of the Mesabi and Cuyuna ranges are hematite and goethite (limonite) as the iron oxides, and quartz and chert as the siliceous gangue, very little is known of the mineralogy and of the chemical and physical characteristics of the slimes, and still less of the interaction between slimes, collector, and the mineral surfaces. For pragmatic reasons iron ore slimes are defined as — 20p material, based upon the calculated settling velocity of a quartz sphere of the stated diameter, and of all other equal-settling mineral particles. Active slime interference with flotation is usually attributed to particles 5p in size or finer, the extent of such interference appearing to depend not only on the mineralogy but also on the size distribution of each mineral in the slime fraction. The objective of this work was to acquire a more specific knowledge of the constitution of iron ore slimes and of their role in flotation. The mineralogi-cal composition of natural slimes was obtained by differential thernal analysis (hereinafter referred to as DTA), electron microscopy, and chemical and X-ray analyses. Some flotation tests were made on natural ore samples. The surface properties of several constituent minerals were investigated by electrophoretic measurements and by determination of the adsorption of some typical flotation collectors. Finally, simplified flotation tests were made on granular goethite and quartz in the presence of various artifically prepared slimes; the results were compared with laboratory flotation tests made on natural ores. MATERIAL AND METHODS Mineralogy of Some Iron Ore Slimes: Samples of two wash-ore tailing::, hereinafter identified as A* and B, *Sample A of the present investigation 18 the same am ore A in ref. 3. of a wash ore C, and of a paint rock D, all from the Mesabi range, were selected for investigation on the basis of prior information concerning their flotation behavior. The two wash-ore tailings, when deslimed, were known to respond well to flotation, whereas the wash ore was high in goethite, tended to be slimy, and responded poorly to flotation. The paint rock also exhibited sliming tendencies, and was suspected to contain relatively large quantities of clay minerals because of its high A1203 content. Gruner states that the paint rock of the Mesabi frequently contains kaolinite. To ascertain the relative sliming tendencies of each sample a standardized desliming method was employed. All samples were ground through 65 mesh using jaw and rolls crushers. A 500-g sample of each

Jan 1, 1962

By C. E. Schwab

A lead-zinc orebody, in fairly strong quartzite and with a dip of 35° to 60°, is block-caved by use of scrams in a stair-step pattern up the ore footwall. Scram linings to handle coarse muck and permit the use of folding scrapers are developed by the use of end-grain wooden blocks to reduce maintenance and keep operating cost to a minimum.

Jan 10, 1953

By P. Lees, N. Parkinson, K. Hartley, D. M. Donaldson

The reprocessing of advanced fuels such as carbides, oxides, and cermets, containing up to 30pct pu has been studied. Dissolution of uranium carbides in nitric acid produces appreciable quantities of mellitic acid which has undesirable effects in subsequent stages of the process. Mixed oxides containing up to about 40 pct Pu in solid solution with UO, are soluble in nitric acid and a leaching type process in nitric acid for a stainless steel/UO,. PuO, fuel containing 30 pct Pu appears to be feasible. It offers considerable economic advantages THE reprocessing of the U-Cr alloy core of the Dounreay Fast Reactor was described by Buck and others at the Second Geneva conference.' This paper described the flowsheet and plant for processing a relatively simple fuel of good dissolution charac- over total dissolution routes. A new oxidation-sub -limation process is described for metallic fuels containing up to 12 pct Mo. New data is presented on the solvent extraction of uranium and plutonium nitrates into tributyl phosphate -odorless kerosene and of the influence of radiolytically produced acid phosphates on this part of the process. It is concluded that there are no insuperable difficulties which will prevent the satisfactory reprocessing of high burn-up plutonium fuels by a solvent extraction route. teristics and of low-plutonium content after irradiation. However, it has been clear for some time that more satisfactory operation of the reactor can be obtained by the use of a core with better irradiation performance than U-Cr alloy and a U-Mo alloy will be used for the next charge. Recent modifications to the core mean that it is now possible to carry out irradiations of fuel element subassemblies similar to those which might be used in a fast power reactor and trials with plutonium-bearing fuel elements will be made in the relatively near future. These changes have meant that a considerable amount of reprocessing development work has had to be carried out for

Jan 1, 1963

By F. W. Osterwald, C. R. Dunrud

A continuously recording seismic network was constructed in 1962 by the U.S. Geological Survey to locate epicenters and record incidence of bumps (bounces, rock bursts) that occur in the bituminous coal mines of the Book Cliffs coal field near Sunny-side, Utah. The coal is mined because of its value as coking coal, although these bumps may be a hazard to life and property. Daily records of tremors caused by bumps for 1 3/4 years indicate that a seasonal pattern, as well as a daily pattern, exists for the number of bumps that occur in a given period. Maxima occur in May and June and November and December. Marked increases at 5-day to 9-day intervals are superimposed on these seasonal maxima. The largest bumps commonly occur during seasonal maxima when the rate of occurrence suddenly decreases and the amplitude of the individual bumps increases. Knowledge of this pattern may lead to prediction of general locations and periods of increased hazard from bumps. Experience to date has shown that prediction of precise times and locations of hazardous bumps is not possible, and may never be; primarily because even a small bump can be a hazard to life and property. Some bumps or bump sequences are actually composites, consisting or two or more discrete bumps a few tenths of a second to a few seconds apart. Violent and spontaneous releases of coal and rock from faces, ribs and roofs of mines (termed bumps or bounces by miners) are a common hazard to life and property in the coal mines located in the Book Cliffs near Sunnyside, Utah (Fig. 1). These bumps

Jan 1, 1965

By S. N. Sharma, William Davis

Because of diminishing energy resources and rising energy costs, every industry is forced to carefully examine its pattern of energy consumption. The copper industry is no exception; current smelting practice begs for technological innovations that would improve the efficiency of its energy utilization. The thermochemical simplicity of copper metal production, as shown in Fig. 1, is deceptive. Designed from the same basic principles, there are four major commercial processes either in use or under construction; and others, such as the Mitsubishi process, are being developed.

Jan 5, 1977

By L. E. Garner

Aggregate resources should be considered primary factors in urban development. Resource planning is essential because land values, previous construction, or zoning restrictions often preempt exploitation of aggregate deposits within an urban area. Sequential land use practices allow development of area prior to urban development population and aggregate consumption trends in Austin, TX, indicate that substantial quantities of reserves will be lost to future development. Aggregate materials are present in nearby areas. However, a comparison of transportation and reclamation costs indicates that reclaiming land after mineral extraction can be significantly cheaper than transporting materials longer distances.

Jan 1, 1982

By Hannu Penttila, Harrison R. Cooper, Olli Mattila

Two approaches to automated operation in metallurgical processes involve the conventional analog control or, more recently, digital control. The expanding use of digital controls applied to process automation is a comparatively new development. Several current technical reports describe digital control systems in concentrator grinding control, 1, 2, flotation, 3 and smelter operations. 4,5 The principle factors influencing trends to digital control are:

Jan 10, 1976

By A. E. Nash

This title is somewhat of a misnomer, because it does not accurately describe the phase of heat generation and application coming within the scope of this discussion. This paper is concerned primarily with that particular phase of radiant-heat transfer sometimes erroneously referred to as "shielded" radiant heat, to differentiate it from the open radiant heat of either flame or settings, in which the actual source of the radiant heat is a small incandescent furnace composed of a highly conductive superrefractory, within whose walls the combustion of the fuel is completed. This small furnace is usually located directly in the furnace proper, and although its refractory walls do shield the heat-absorbing surfaces from contact with the gases of combustion, there is no interference with the radiant heat given off by the furnace itself. We do not believe it either necessary or advisable to shield or screen radiant heat when properly controlled and applied. We do believe it essential to prevent the excessively hot gases of combustion from coming in contact with those parts of the heat-absorbing structure that are already receiving heat at high rates by radiation. In connection with any process for the refining of oil with which we are familiar, we are convinced that it is most advantageous to transfer the maximum of the heat generated in the form of radiant heat, applied directly to the heat-absorbing surfaces without the interposition of any form of shield or screen to prevent or reduce the radiant-heat transfer. While the term radiant heat is broadly used to cover all heat energy transferred from one body to another by radiation, in contradistinction to heat given up by gases in direct contact with the heat-absorbing structure (convection) or transmitted simply by conduction, in furnace work it is perhaps more often limited to the heat rays given off either by

Jan 1, 1928

By Dever Ashmead

ENGINEERS, operators, miners, and others di-rectly interested in mining will readily agree that more of well-directed illumination in mines will result in a reduction of accidents and general im-provement in the working conditions, comfort, and effi-ciency of those employed underground. Progress has been made in the amount of illumination from individual lamps carried by miners. The candle, which a great many of us can remember as the general method of lighting, was replaced by the oil lamp or torch, later by a specially prepared oil known as "Sunshine," and eventually by the carbide cap lamp. The metal mines still present a field for progress from the standpoint of general illumination, particular-ly those mines having high stopes. Attention is being more and more focussed upon the advantages of im-proved lighting in mines, in order that the underground employee may benefit as the factory workers have al-ready done. The management is vitally interested in the morale of its employees, the reduction of costly accidents and increased production, all of which, judging by results in other industries, will be sub-stantially benefitted through the means of improved general illumination. From data available to the writer, 40 to 50 per cent of the accidents in the metal mines occur at the face; they may be due to roof falls, movement of loose ore, loading of cans, handling of tools, etc. Very probably a large proportion of these accidents may be attributed to lack of light. If sufficient illumination had been present the employee could have seen what was happen-ing and taken the proper precautions. The introduc-tion of better illumination means better visibility, de-crease in accidents, and increase in efficiency.

Jan 6, 1928

By Nicholas J. Grant, Henry Epstein, John Chipman

FOR many years steel producers have been concerned with the presence of hydrogen in steel. Hydrogen dissolved in excess of its solid solubility at the melting point may cause bleeding and gross unsoundness in ingots and castings. In fully-killed steels the hydrogen content which results in these difficulties varies with the alloy content1 and may range from 6 to 12 ppm.* It is also recognized that of heat treatment diminishes rapidly as the size of the part to be treated increases. The time required to remove a specified fraction of the hydrogen present increases as the square of the diameter of the section, making the treatment of large- sizes impractical. In order to prevent bleeding and gross unsound-ness due to hydrogen, and in view of the inadequacy of corrective heat treatment alone to provide optimum properties when hydrogen is present in large sections, efforts to limit the hydrogen content must be taken while the steel is still liquid. The main subject of this paper is a discussion of the factors affecting the hydrogen content of liquid steel in acid and basic open hearth, and basic electric two-slag furnace processing. Literature Survey Because many of the results and observations reported in the literature have a direct bearing on the results obtained in the present research and form part of the basis for conclusions reached, a brief summary of the findings is necessary. Methods for experimental investigation of hydrogen in liquid steel are comparatively new. The first attempts to estimate the hydrogen content of the open hearth bath were by Kalling and Rudberg,6 who devised a method for collecting gases evolved from the boiling bath of a basic open hearth furnace. They found that the gas during the boil generally contained 2 to 3 pct H2. From this and Sieverts'

Jan 1, 1958

By William F. Blake

The discovery of tin-ore in the Black Hills of Dakota dates from June, 1883, and short preliminary notices were published in September of that year.* The discovery-point is known as the Etta Mine, in the central portion of the Hills, about six miles east of

Jan 1, 1885

BOSTON. SECTION W. E. C. EUSTIS, Chairman, H. L. AGASSIZ, Vice-Chairman., E. E. BUGBEE, Secretary-Treasurer, Mass. Inst. of Technology, Boston, Mass. ALBERT SAUVEUR, H. L. SMYTH. The 37th meeting of the Boston Section was held at the Engineers' Club, on Monday evening, Oct. 2, 1916. Fourteen members and guests attended the dinner. The Society was fortunate in having present not only the announced speaker, J. G. Carleton of Marblehead, Mass., but also a brother member from afar, Thomas Warner of California. Mr. Carleton, who has spent the' past few years in South America, gave an informal talk on the mining of the precious metals on the South American continent. He drew a comparison of the geographical distribution of the precious metals in North and South America and pointed, out the similarity in the geological occurrence of the eastern mining, regions, mentioning particularly Venezuela and Brazil. He also directed attention to the fact that the great placers of the northwestern part of North America had their counterpart in the gold-bearing region of Columbia. The marked contrast between the southern end of North America, so rich in metals, and the southern part of South America, so poor in mineral deposits, was clearly brought out. It is difficult to avoid the conclusion that the South American Cordillera is less intensely mineralized, than the corresponding mountain.

Jan 1, 1917

By D. H. Newland

Certain observations from the field and laboratory suggest the need for recasting some of our ideas about gypsum as a rock-forming mineral and in relation to supplies for industrial use. Until about 25 years ago, the use of gypsum was confined almost entirely to agriculture. During the past quarter century, though, its usefulness has been greatly developed, particularly in the building trades, which now absorb most of the gypsum produced. In 1919, according to the U. S. Geological Survey, the output of crude gypsum was 2,240,163 tons, a gain of 912 per cent. in 25 years. About one-half of this production was mined in New York, Ohio, and Michigan, where the proved supplies can hardly be regarded as over-large when viewed in relation to the rapid expansion of industrial requirements. The occurrence of gypsum in the United States is treated by R. W. Stone and others.' The deposits of Canada are described by L. H. Cole. Several states, including Kansas, Oklahoma, Iowa, Michigan,and New York, have made special surveys of their gypsum deposits, but the reports, as a rule, refer to conditions as they existed from 15 to 20 years ago. Association of Gypsum and Anhydrite The two calcium sulfate compounds, gypsum (CaSO4.2H2O) and anhydrite (CaS04), are the more stable forms of a series which includes at least two other members, so-called half-hydrate (CaSO4.1/2H20) and soluble anhydrite (CaS04). Each of the latter readily takes up water to recrystallize as gypsum and consequently is incapable of existence under ordinary geological conditions; also each can be prepared from gypsum by the application of heat within certain temperatures, the process on which is based the manufacture of commercial plasters. If the temperature limitations are not observed, the result of the calcination process will be insoluble anhydrite which, compared with the soluble form, takes up water very slowly so as to be of no practical use, although actually it is soluble and in time is convertible into gypsum like the other forms.

Jan 1, 1922