Search Documents

By Marston G. Fleming

E. C. Peterson (Anaconda Copper Mining CO., Darwin, Calif.)—A study of this quite comprehensible and interesting paper by Dr. Fleming brings to mind several observations in the practical application of alkalinity and related factors to the actual practice of lead mineral flotation. Soda ash has long been a widely used and a very helpful alkaline conditioning agent in the flotation of galena from the usual run of lead-zinc ores. Soda ash is one of the common "standard" conditioning agents tried in any laboratory investigation of lead-zinc ores because it has so often proved helpful to galena flotation. However, the use of soda ash in the actual flotation of oxidized lead ores is certainly not widespread. In the flotation of certain lead-zinc ores from the Park City district of Utah, it was found in the usual cyanide-zinc sulphate-xanthate circuit that soda ash had an effect of producing a very condensed and flat froth regardless of the many frothers tried and that substitution of lime for soda ash to produce the same pH (8.0 to 8.4) improved the froth condition. However, the flotation of coarse particles of galena became so critical that some would pass through into the tailing, but caustic soda as a substitute for either soda ash or lime produced a very desirable froth condition in the same pH range and greatly improved the metallurgical outcome. Milling was carried out in typically "hard water" from watersheds of limestone and other calcareous rocks and the ore also apparently contributed magnesium and calcium salts to the pulp. Certain lead-zinc ores of Mexico have shown their greatest flotation response in circuits conditioned with sodium bicarbonate, and such actual mill use was also believed to be related to the water necessarily used in milling. On other lead-zinc ores the optimum has been obtained in actual milling treatment by use of caustic soda in both circuits of the operation. In flotation of oxidized lead ores in which sulphidi-zation is employed by addition of sodium sulphide, very high pH's exist in the flotation circuit. With the usual oxide lead ores, demanding 5 to 15 lb of sodium sulphide per ton of ore, pH's in the circuit (closed and open water-circuits) may range from 9.5 to 12, and for ores that contain much anglesite or a high percentage of iron oxide minerals, sodium sulphide consumption may reach as much as 30 lb per ton of ore and the resultant pH will be correspondingly higher. Yet in such flotation treatment employing either xanthate or oil (high-sulphur crude oil or diesel oils) as the collector, satisfactory to excellent grades of concentrate and lead recovery are obtained. Although there have been great studies and accomplishments in the investigations of flotation fundamentals and flotation theory, and although an investigation to determine the effect of all factors entering into the actual plant flotation of sulphide and oxide ores must become very complicated, as Mr. Fleming has mentioned in his caution regarding the drawing of general conclusions for other ores, it seems that it would be of greater interest if the techniques and investigations could, with time, approach the conditions of actual practice and lead the way to improved and more efficient flotation plant performance. Marston G. Fleming (author's reply)—The gulf between fundamental flotation research and plant operation is, perhaps, less wide than Mr. Peterson suggests. For example, the work described in my paper developed from an extensive investigation of a complex lead-vanadium ore from southwest Africa. This investigation started as a standard ore-testing problem but, at almost every stage, results were obtained which could not be interpreted in terms of previous experience. A program of fundamental research was therefore undertaken and was closely interlocked with the ore testing. This coordinated investigation resulted in a flotation process which has now been proved by two years of successful plant operation, and although the grade and mineralogical constitution of ore as well as smelter requirements have altered more than could have been anticipated, our knowledge of the fundamental character of the problem has made it possible to meet each change in conditions with much more confidence than would have been the case had we neglected this aspect of the investigation.

Jan 1, 1954

By R. L. Curfman

In May 1960, six months after conversion of one- half of the Uranium Reduction Co. mill from acid to alkaline leach, severe corrosion was encountered in the 112 stainless steel wash baskets in the resin- in-pulp portion of the uranium circuit. Fortunately the corrosion was limited to the stainless steel screen cloth and bolts. The frames were not affected. Each resin-in-pulp wash basket serves as a container and a vehicle for approximately 40 cu ft of ion-exchange resin. Four baskets are installed in each tank through which uranium-rich solution flows as the baskets move up and down mechanically in the tank. The ion-exchange resin has an affinity for the uranium in the solution which causes it to be deposited on the resin in solid form. By reverse action with different chemical solutions, the uranium may be stripped from the resin for further processing and purifying. This section is the first step in the actual recovery of the uranium.

Jan 9, 1962

By W. Klement

By quenching liquid alloys, single-phase solid solutions are obtained in the ranges 0 to 42.0 at. pct Co-Au and 0 to 15 and 75 to about 100 at. pet Co-Cu. Metastable solid solutions are also found in multiphase 42.0 to 49.0 and 69. 0 to about 100 at. pet Co-Au alloys. fie inability to achieve complete solid solubiliiies in Au-co and cu-co alloys is rationalized by a conszderation of the rate processes during cooling and solidification. Trends in lattice distortion and shifts in the compositions of the melting-point minima and critical points are discussed for the binary alloys of copper, silver, and gold with some of the transition metals of the first long period. By rapidly cooling alloys from the melt, a continuous series of metastable solid solutions can often be obtained for components of similar crystal structure which normally form eutectic systems.' The eutectic system Au-Co, Fig. 1, and the peritectic system Cu-Co, Fig. 2, were investigated in order to determine the extent of the metastable solid solutions attainable with the present technique.* EXPERIMENTAL PROCEDURES Most of the alloys were prepared by melting weighed quantities of the elements (purity greater than 99.9 pct) under hydrogen in alumina crucibles by means of induction heating. After reweighing, the alloys were cast under argon into 1 mm diam wires. However, it was not possible to prepare some of the Cu-Co alloys with the requisite homogeneity (over about 1 mm3) in this way. For these alloys, reduced powders (purity greater than 99.9 pct) were mixed for 12 to 48 hr, pressed into compacts that were sintered at 1000º to 1050°C for 6 to 48 hr under hydrogen, and then furnace-cooled. Alloy charges of a few mm3, cut from the cast wires or chipped from the sintered compacts, were heated to 1550º to 1600°C in 30 sec in an alumina insert held within a graphite support and then ejected by a pulse of helium onto a lightly polished copper strip on the inner periphery of a rotating wheel. The

Jan 1, 1963

By D. R. Parrish, W. E. Lamoreaux, W. W. Owens

Several methods are now being used by the industry for determining the gas-oil flow characteristics of reservoir rock samples. Most of the laboratory experirnerltal rlzethods can be classified either as steady-state, unsteady-state, or Hassler-type tests. Although the validity of the results obtained by any specific method is not questiorzed, in general, the complexity of these methods leaves much to be desired. This investigation dealt primarily with the development of a simplified unsteady-state (gas drive) laboratory test method for measuring kg/ko re1ationships of small core samples. A procedure for selecting uniform and representative sandstone rock samples was developetl since it was observed that the reliability of the test resu1ts was dependent upon having a sample which was uniform in porosity and permeability. The importance of factors known to influence the results of this type test, such as oil viscosity, gas expansion, and pressure differential were eva/uated. The method of calculating the test results was found to give valid data over a wide range of gas expansion. The limits of pressure differential and oil viscosity which would insure reliable results were defined. In cornparisorz with other presently used testing methods, the gar drive method requires considerably less apparatus, is less time consuming, and is more readily adaptable to a routine type core test. INTRODUCTION The detcrmination of the gas-oil flow characteristics of reservoir rocks has been given concentrated study by the oil industry for the past decade. Both analytical and experimental methods have been considered. The analytical methods have generally relied on a simplified characterization of porous materials in order that the fundamental laws of fluid flow and capillarity could be utilized. More direct experimental methods have been proposed by numerous production research laboratories with the primary goal being a simple and inexpensive, yet reliable method for measuring the gas-oil flow characteristics of reservoir rock samples. The experimental methods which have been reported in the literature generally can be grouped into one of the following classifications: 1. Steady state1,2,3,4 in which a fixed ratio of flowing fluids is forced through the test sample until equilibrium conditions of saturation and pressure gradient are established. 2. Hassler or stationary liquid method5,6,7 in which a uniform liquid saturation is attained, usually through capillary desaturation, then gas or oil is flowed through the sample at a pressure drop insufficient to disturb the pre-established saturation. :. Non-steady state method1,8,9,10 In which only the gas phase is injected into the sample, causing displacement of the oil phase and resulting in a system of continually changing average saturation and saturation gradient. The steady-state and Hassler methods have been most popular because, no doubt, of the simplicity of the actual relative permeability calculations. The problems involved in these methods were limited to apparatus design and measurement techniques. In the steady-state method, for instance, a constant flowing fluid ratio is established which, at equilibrium, results in an essentially uniform saturation over the entire length of the test sample. Therefore, the basic flow characteristics could be obtained by correlating the average saturation of the test sample with the kg/ko determined at various flowing gas-oil ratios.

Jan 1, 1957

By Gail Moulton

THE oilfields in Illinois are located principally along the LaSalle anti-cline in the southeastern part of the state. The oil produced comes most largely from beds of Pennsylvanian and Mississippian age, but there is an increasing important production from deeper horizons, as will be noted under new development. The oil is largely of paraffine base, and has an average specific gravity of about 35° Baume. The rank of Illinois as an oil producer has dropped from third since 1913, when its production was exceeded only by that of California and Oklahoma, to eighth in 1923. This has been the result of failure to find new pools of considerable size to offset the declining production of the old wells and of the greatly increased production of some of the other states. The noteworthy features of petroleum production in Illinois during 1924 are: the low rate of decline for the state as a whole; the smaller percentage of dry holes; and the larger average initial yield of the new wells.

Jan 3, 1925

By M. H. Brady, J. G. Roscoe

Continental No. 1 This mine in Lisbon Valley has an orebody about 1200 ft long and varying from 250 to 70 ft wide. Average width is about 100 ft and stope heights average about 9 ft. It was developed by a 350-ft, 11º inclined shaft for trackless haulage, although a hoist and track are installed for auxiliary hoisting. Mining has been done from horizontal open stopes with random pillar support, using a HD5 tractor for mucking and a 4-wheel drive Gettman shuttle car for tramming. Slushers have been used to some extent in thin ore zones. Back support for stopes and haulage ways has been accomplished by rock bolts and landing mat. The most interesting feature of this mine has been pillar extraction. Mining was done under contract during the first year of operations with little regard for an orderly plan of stope layout or regularity of openings. Most of this work was done in the largest area of the orebody; consequently, pillar recovery has been accomplished under conditions which are far from ideal. However, a workable system has been developed which is competitive, both in cost and production rate, with open stoping.

Jan 7, 1958

The useful minerals can be subdivided into two large groups. One comprises those which are mined because of their chemical composition. They represent the natural resources of certain materials or of energy (coal). The second group is used not because of their chemical composition but because of certain physical properties or combinations of physical properties. A large number of minerals are mined because of their hardness, their electrical and thermal properties, their color or plasticity. There has been increasing recognition of the value of mineral synthesis during the past 30 years. This is illustrated by the development of improved aircraft spark plugs and chemical porcelain about the time of the first World War. During World War II the impact of crystal chemistry upon ceramics became most pronounced. New ceramic bodies were tailor-made, such as those designed with a high dielectric constant and low power loss, for use in high-voltage, high-frequency communication. In the field of refractories special materials were needed for unusual heat-resisting service in jet and rocket engines, and in the processing of fissionable materials. The synthesis of natural minerals in the laboratory has long been of aid to geologists and mineralogists in their study of the origin of minerals and physico-chemical conditions under which certain minerals were

Jan 1, 1950

By T. H. Janes

NATURAL abrasives of some type are found in all countries of the world. In order of their hardness the principal natural abrasives are diamond, corundum, emery, and garnet, which are termed high grade, and the various forms of silica, including pumice, pumicite, ground feldspar, china clay and, most important, sandstone. The properties qualifying materials for use as abrasives are hardness, toughness, grain shape and size, character of fracture, and purity or uniformity. For manufacture of bonded grain abrasives such as grinding wheels, the stability of the abrasive and its bonding characteristics are also important. No single property is paramount for all uses. Extreme hardness and toughness are needed for some applications, as in diamonds for drill bits, while for other purposes the capacity of the abrasive to break down slowly under use and to develop fresh cutting edges is of greatest importance, as with garnet for sandpaper. In dentifrices, soaps, and metal polishes, of course, hardness and toughness are objectionable.

Jan 10, 1954

By O. Bergmann, R. E. Lueders, R. R. Ellefson, H. M. Brennecke, D. S. Davies

A new hydrometallurgical process has been developed to recover copper from sulfide ores. Copper is leached in a staged reactor system utilizing nitric and sulfuric acids at 105OC. Iron is removed from the pregnant liquor as a jarosite, and cathode copper is electrowon directly from the purified pregnant liquor. The spent electrolyte is recycled. Nitrogen oxides evolved from the leach are reconverted to nitric acid and are also recycled. Sulfur is rejected as So, jarosite, and gypsum. The process is highly versatile and can recover precious metals, molybdenum, and zinc when these elements are present. Continuous, integrated, semi-pilot plant operations using chalcopyrite ores demonstrated 99% copper leaching and production of cathode grade copper. Economic evaluation shows that the process is competitive with pyrometallurgical and other hydrometallurgical processes.

Jan 1, 1982

By Michael Hoch, Walter C. Wyder

The Cr-Ni system was investigated between 900" and 1400°C and 45 to 100 wt pct Cr. The Cr-Fe system was studied between 1200" and 1385°C and 70 to 100 wt pct Cr. Powdered alloy compacts were produced from high-purity chromium, nickel, and iron poulders. The compacts were sintered in an argon atmosphere and then machined into small, 0.030-in. diam cylindrical specimens. These were then heated by induction in the high-temperature X-ray diJfractwn camem under a helium atmosphere and irradiated with copper Ka radiation. From the results of the high-temperature X-ray diffraction patterns it can be concluded that chromium exists only in the bcc form, and that no eutectoid reaction occurs in the Cr-Ni system in the temperature interval 900" to 1400°C. The X-ray diffraction patterns are in agreement with the Cr-Ni phase diagram of Bechtoldt and Vacher, and Williams. It is possible that chromium undergoes one or more allotropic transformations between room temperature and its melting point. Most of the evidence was gathered from the study of the chromium-rich ends of the Cr-Ni and Cr-Fe binary systems. All the investigations rely heavily on indirect methods: thermal analysis, electrical resistivity, and micro-graphic inspection of quenched samples. In the present work the chromium-rich side of the Cr-Ni and Cr-Fe binary systems is studied, using high-temperature X-ray diffraction techniques. Thus the coexistent structures can be observed directly at temperature. PREVIOUS INVESTIGATIONS ~ansenl shows two possible Cr-Ni phase diagrams 1) a simple eutectic [Liquid =a-Cr(bcc) + y-Ni(fcc)], 2) a eutectic [Liquid+ P-Cr(fcc) + y-Ni(fcc)] and euctectoid [p-Cr(fcc) ==a-Cr(bcc) + yNi(fcc)]. The latter is based on the work of Grant and co-workers.2 Stein and rant'" placed the eutectoid composition at 1215°C and 68 wt pct Cr; their diagram is shown in Fig. l. Similarly, Sully3 also discusses the two proposed diagrams. Price and Grant,4 working on an isothermal section of the Cr-Ni- Fe ternary diagram at 1300°C, made no mention of a ß-chromium phase (fcc). The ß-chromium structure was also reported by Misencik 5 in the Cr-Nb(Cb) system. Williams 6 studied the Cr-Ni system using precipitation techniques. His work included the chromium and nickel solvus lines below 1250°C. He reported no ß structure nor any eutectoid reaction. The solvus lines which he produced were very similar to those of Jette, et al 7 below 1000°C. He concluded that Grant and coworkers2 had misinterpreted their data, and that effects which they had reported were actually due to the rapid and extensive precipitation of the nickel-rich phase. Bechtoldt and vacher8 used sintered powdered alloy compacts in an attempt to find the ß phase. They used metallographic and room-temperature X-ray diffraction techniques and also failed to detect the fcc chromium phase. They attributed the low slope of the chromium solvus at approximately 1150°C as the probable cause of the abundant precipitation obtained. They also stated that the precipitation was the probable cause for the abrupt discontinuities in the thermal analysis and electrical resistivity data which led to the conclusion that a eutectoid reaction existed. Fig. 1 also shows their diagram. Grigor'ev and coworkers9 investigated the polymorphic changes of chromium in the Cr-Ni phase diagram. Using standard microstructural and thermal analysis techniques, they published a phase diagram which contained five polymorphic forms of pure chromium and four eutectoid reactions. They stated that the room-temperature bcc chromium transformed to a fcc structure at 930°C, to bcc at 1300°C, to hcp at 1650oC, and then finally to bcc at 1830°C. The eutectoid reactions were placed at 850°, 960o, 1140°, and 1220°C. Also to be noted was the fact that the uppermost phase, the bcc above 1830°C, was different from the upper phase of Grant and coworkers,2 the fcc above 1840°C. Their eutectoid reactions, temperatures and compositions fall

Jan 1, 1963

By H. W. Schull

The Alligator Ridge gold deposits are located in northwest White Pine County at the southwest end of Alligator Ridge. Alligator Ridge is on the west side of Long Valley in the range of hills that separates Long and Newark valleys. The nearest population center is Ely, about 113 km (70 miles) to the southeast. Access to the Alligator Ridge gold mine from Ely is via US Highway 50 and the Long Valley Ruby Marsh Road. The latitude and longitude is approximately 39° 45' north and 116° 30' west. The Alligator Ridge gold deposits occur in the lower 61 m (200 ft) of the Mississippian-Devonian Pilot Shale formation, a laminated calcareous carbonaceous siltstone. The gold deposits contain carbonaceous, oxide, and jasperoid type gold ore. For more details on the geologic features of the deposits, see Schull, Sutherland, and Ilchik (in press). The discovery story of Alligator Ridge began in the spring of 1976 when the areas mapped as jasperoid on the 1:250,000 scale geologic map of White Pine County (Hose and Blake, 1976) were examined and sampled. Seventeen samples, about 23 kg (50 lb), were collected from an area about 0.65 km2 (0.25 sq mile). Of these 17 samples 10 reported atomic absorption values of less than 0. 1 ppm Au and 7 reported values in the 0.1 to 1.0 ppm Au range. In June of 1976 20 lode claims were staked to claim the area of the rock chip sampling. The claims' end and side center lines were used as a grid for soil sampling. Sample stations were 91 m (300 ft) apart and sample lines were 229 m (750 ft) apart. The samples were sieved to - 180 µm (- 80 mesh). Out of 99 soil samples, seven samples reported Au values in the 0.1 to 1.0 ppm range. Of the seven auriferous samples, five were located over the jasperoid outcrops previously sampled; one over unmineralized Pilot Shale a few hundred m (ft) downslope from some Au-bearing jasperoid; and one from a 15 x 15 m (50 x 50 ft) talus outcrop area of hitherto unnoticed mineralized Pilot Shale. Subsequent sampling, mapping and drilling would show that this 15 X 15 m (50 x 50 ft) outcrop area was the top of the Vantage 1 ore body, about 1.27 Mt (1,400,000 st) of over 3 g/0.9 t (0.11 oz/st) Au. Late in the summer of 1976 about 30 more 1.4 to 2.2 kg (3 to 5 lb) rock chip samples were collected in the course of preliminary geologic mapping. This mapping and sampling showed that the gold-bearing jasperoids occurred at the contact between the Pilot Shale and the underlying Devils Gate Limestone. Rock chip samples of 0.1 ppm Au or greater were restricted to the jasperoids and the mineralized outcrop area of Pilot Shale located by the soil sample survey. Rock chip samples from the area of mineralized Pilot Shale were in the 3 to 5 ppm Au range. Activity resumed in the summer of 1977 with a more detailed soil geochemical survey. The jasperoid areas were defined as large geochemical gold anomalies of values greater than 0.1 ppm and locally greater than 0.2 ppm Au. Soil samples from the area of mineralized Pilot Shale outlined a greater than 0.1 ppm gold anomaly 61 x 152 m (200 x 500 ft) in size. Further geologic mapping showed that elsewhere, even where bleached and silicified, the Pilot Shale areas were geochemically very low in gold (less than 0.1 ppm Au). In November, 1977 twelve rotary percussion drill holes were drilled to test the gold-bearing jasperoid areas and the mineralized Pilot Shale area. Drilling of the jasperoid areas showed that the jasperoids gave way at shallow depths [less than 24 m (80 ft)] to unmineralized unaltered Devils Gate Limestone. A five hole cross pattern was drilled to test the area of mineralized Pilot Shale. Four of the five holes re-

Jan 1, 1985

By J. T. Burwell

THE crystal orientation in silicon iron that has been given a particular treatment described by Goss,1 has been studied by Goss, by Bozorth2 and by Sixtus,3 but their results do not agree and are almost entirely qualita-tive. The following pages give a description of the orientation of the crystals in the material as determined by means of X-rays and expressed graphically in a pole figure. The treatment consists of hot-rolling the material into strip and then giving it two cycles of cold reduction followed by recrystallization. This produces remarkably good properties in the rolling direction, the product having a maximum permeability in this direction of more than 25,000 and a permeability at 16,000 Gauss of more than 2200, It is now generally agreed that Goss's original conclusion' that the crystals in the final product are randomly oriented was incorrect, since Bozorth2 and Sixtus,3 using different methods, have shown that there is a decided preference in orientation. Those writers, however, expressed their results only in terms of one or more ideal orientations with deviations therefrom.

Jan 1, 1940

By A. J. Fenn

Long experience with underground mining inspired the unusual idea of using an underground crusher-conveyor system as a substitute for surface haulage at the Cananea open-pit copper mine in Sonora, Mexico. Now implemented and working well, the system has born out the expectations of its originator, Cia. Minera de Cananea S.A. de C.V., that it would effect substantial cuts in the high cost of haulage. The Cananea deposit is a large, low-grade orebody above the mined-out Colorada pipe which was once one of the largest high-grade underground deposits in the district. Present facilities at the pit consist of: (1) A large open-pit mine capable of moving 80,000 tons of material per day with a shovel-truck, underground crusher and belt conveyor haulage system. (2) A 25,000-tpd concentrator equipped for four stages of crushing, rod mill-ball mill grinding with cyclone classification, and flotation in conventional machines. (3) A dump leaching process producing 1 million lb of copper per month in a tin-can scrap precipitation plant. (4) A two-reverberatory, six-converter smelter which can make 140 tons of blister copper per day. (5) A well-integrated contingent of supporting departments running the gauntlet from housing to power generation.

Jan 3, 1969

By Henry Logan

THE purpose of mine-hoist safety con-trollers is to prevent hoists from being operated at speeds above those considered safe and expedient, to ensure proper accel-eration and retardation near the ends of travel, and to prevent overwinding. In other words, they are to safeguard the normal speeds and movements of the hoist-ing drums and cages. The object of this paper is to explain the fundamental principles of hoist controllers, and to aid in their selection, installation, and maintenance. There have been many designs of me-chanical hoist controllers, the basic ele-ments of which as ultimately developed consisted of a flyball governor and another movable member supported by a frame and arranged to move in a vertical, horizontal, or rotary direction, depending upon the particular design, the whole mechanism arranged to be driven in synchronism with the hoist drum. In case of overspeeding, inadequate retardation, or overwinding, a pawl or catch controlled by the governor would engage teeth or dogs on the moving member, which through mechanical con-nections would cut off the power and set the brakes.

Jan 1, 1940

[ ]

Jan 1, 1938

By W. D. Von Gonten, R. L. Whiting

Regression analysis was used to correlate the physical properties of 478 sandstone and 90 carbonate core samples. Porosity, permeability, electrical formation resistivity factor, capillary pressure and the sonic velocity of the shear and compressional waves were measured. Prediction equations for porosity, permeability and electrical formation resistivity factor were found which should be useful in understanding the relationships between the physical properties of porous media in formation evaluation. INTRODUCTION The physical properties of porous media are important to the petroleum engineer and geologist. To evaluate fully the potential and behavior of a subsurface formation such as a petroleum reservoir, certain physical properties of the porous medium must be known. The problem of accurately determining physical properties of subsurface formations has not been solved because many determinations must be made by indirect measurements and because of the difficulties caused by complex pore structure and presence of clays in most naturally occurring porous media. Due to the difficulty in measuring some of the physical properties of porous media, it would be advantageous to be able to predict a certain physical property of a rock from other physical properties of the rock which could be measured more easily and more accurately. Since most potential reservoir rocks are heterogeneous, relationships between the physical properties are very complex and thus far no satisfactory correlations based on theory or laboratory models have been developed. It appears that empirical relationships obtained by measuring the physical properties of a large number of samples of naturally occurring porous media and applying regression analysis to develop equations for one physical property in terms of other rock properties is the best approach. REVIEW LITERATURE The three physical properties used as dependent variables for correlating purposes were porosity, permeability and formation factor. Since formation factor is more difficult to determine, a brief review of the literature is provided on this property. The first work on determining formation factors was published by Archie1 in 1942. He defined this property of a porous medium as F - Ro/Rw......(1) where Ro is the resistivity of the porous medium when completely saturated with a brine of resistivity Rw. Archie found the best correlation between formation factor and porosity was the following equation, where is the porosity fraction and m is the constant characteristic of the rock. The value of m was 1.3 for unconsolidated sand packs, and ranged from 1.8 to 2.0 for consolidated sandstones. In 1950 Patnode and Wyllie2 and De Witte3 observed that the formation factor as determined by Eq. 1 was valid only when the porous medium contained no conductive solids such as clay or shale. When conductive solids are present the formation factor is also dependent on the resistivity of the saturating fluid. Therefore, in samples containing conductive solids the formation factor decreased as the resistivity of the saturating fluid increased. Because of this. the measured formation factor was called the apparent formation factor and was designated Fa. Patnode and Wyllie proposed the following equation,

By Carl Samans

IN their recent complete review of the subject of age-hardening,1 R. F. Mehl and L. K. Jetter classify the main types of precipitation-hardening alloys under two headings, depending upon the nature of the precipitate and the character of the precipitation. In the alloys falling under the first heading, which display "continuous precipitation" and are typified by the aluminum-copper alloys, "precipitation seems to occur without much regard to grain boundaries and apparently at much the same rate at every point," although an acceleration in regions plas-tically deformed has definitely been established .2 In the second type of alloys the precipitation is "discontinuous," as in the copper-silver system for example, and "seems to start in restricted regions, primarily those contiguous with the grain boundaries, and to spread inward in an advanc-ing wave." The reasons for the occurrence of these two greatly different types of precipitation are unknown, as are those for many other reactions that take place in the solid state. In the present paper only the first or "continuous" type of precipita-tion will be dealt with, for which a complete crystallographic mechanism has been worked out for the process of precipitation from a supersaturated solid solution of copper in aluminum. Based upon this mechanism, an explanation of the various property changes found experimentally will be developed in the second paper of this series. In later papers "dis-continuous precipitation" in copper-silver alloys will be explained, and an effort will be made to rationalize the two processes and types of precipitation.

Jan 1, 1940

By Susanne Pignolet, Richard D. Hagni

Ore microscopy has been applied to the complex cobalt-nickel- copper-lead-zinc ores from the Madison Mine in the Fredericktown subdistrict of the Southeast Missouri Lead District to predict potential beneficiation problems. It has been found that in some portions of the ore deposit, textures are present which may result in metal losses. In ores from the Bonneterre Transition Zone the intimate association of siegenite with chalcopyrite may result in cobalt and nickel losses to the copper concentrate and nickel contamination of the copper matte at the smelter. In ores from high stratigraphic horizons, this association is relatively uncommon, and siegenite is commonly associated with bravoite. This latter association will increase the the recovery of cobalt and nickel in the siegenite concentrate. However some cobalt and nickel will be lost to the tails as bravoite-pyrite particles due to the intimate intergrowth of these minerals. Other textures which may result in beneficiation problems include the intimate intergrowth of chalcopyrite and galena and the occurrence of sphalerite as inclusions in galena.

Jan 1, 1984

By S. Skowronski, K. W. McComas

Page Purpose of investigation.....................'. 354 Details of experiments........................ 357 Experiment Series No. 1, melting copper containing chlorine under carbon dioxide............................... 358 Experiment Series No. 2, melting hydro-electric cathode copper drillings under air................................ 362 Experiment Series No. 3, melting hydro-electric cathode copper drillings under furnace gases............................ 363 Summary.............................. 364 Purpose of Investigation Since cuprous chloride melts at 418' C., boils at 954' C. to 1032' C.,' and is known to be volatile at a much lower temperature, the presence of chlorine in any form in or on copper to be melted has always been looked upon by copper refiners as a possible source of serious copper loss. Although this fact has been known for some time, the copper literature contains little or no information regarding it and the field seems never to have been properly investigated from a metallurgical standpoint. According to Greenawalt,2 cupric chloride, CuCl2, when ignited gives cuprous chloride; therefore cuprous chloride is always formed when copper enters into reaction with chlorine at a high temperature. Cuprous chloride melts somewhat below a dull red heat, and does not volatilize in closed vessels, even if strongly heated, but if heated in the air it goes off as a white vapor, Hofman3 gives the melting point of cuprous chloride

Jan 1, 1919

NAME AND OBJECT. SEc. 1. This Institute is incorporated under the Membership Corporations law of the State of New York ; its corporate name is American Institute of Mining Engineers; and its objects are such as are stated in its Certificate of Incorporation. ARTICLE II. MEMBERS. SEC. 1. The membership of the Institute shall comprise four classes, namely 1. Members ; 2. Honorary Members ; 3. Associates ; 4. Junior Members. All members shall be equally entitled to the privileges of membership, except¬ing that Honorary Members, Junior Members, and Members and Associates whose residences shall be outside of the United States, Mexico, and Canada shall not be entitled to vote. Members and Associates residing within the United States of America, Mexico, and Canada, and not in arrears for dues, shall be entitled to vote in person at the meetings of the Institute, or, as hereinafter provided for, by letter ballot. SEC. 2. The following classes of persons shall be eligible for membership in the Institute, namely : as Members, all professional mining . engineers, geologists, metallurgists, or chemists, and all persons actively engaged in mining and metal¬lurgical engineering, geology, or chemistry ; as Associates, all persons desirous of being connected with the Institute who in the opinion of the Board of Directors are suitable.

Jan 1, 1923