Search Documents

By J. A. Herbst, O. A. Bascur

Fine coal cleaning by froth flotation has become common practice in the US with more than 73 kt/d (80,000 stpd) treated in this way. In spite of this large tonnage, developments in the automated control of coal flotation circuits have lagged significantly behind those for mineral systems. The primary reason is that instruments have not been available for the online measurement of carbon ash content or other critical variables in coal slurries. A second reason is that the influence operating variables have on coal flotation are not completely understood. During the last few years, some of the needed instrumentation has been developed, while an improved knowledge of the flotation process itself has occurred through mathematical modeling. As a result, certain control strategies for coal flotation are beginning to emerge. This paper attempts to evaluate several control strategies using a detailed flotation dynamic simulator, Dynafloat. After construction of a process matrix for the system of interest, promising alternatives for linking manipulated and controlled variables were analyzed. To develop combined grade and recovery control strategies, it was necessary to construct a grade/recovery map with the aid of the simulator to drive the system to known, final, feasible grade/recovery operating conditions. Finally, an advanced strategy that uses an on-line model to identify disturbances and take control actions is proposed.

Jan 1, 1986

By C. G. Dunn, P. K. Koh

THE primary recrystallization texture in cold-rolled silicon iron, which is the matrix texture for developing the Goss texture or the cube-on-edge texture by secondary recrystallization at temperatures near 900°C,1-5,21 has not been adequately described. Thus from the present available information, it is not possible to explain satisfactorily both the grain-growth selectivity of the matrix and the often observed magnetic torque curve, which itself provides some information on the texture. Also lacking is information on the special annealing texture that develops in this material when the annealing temperature is 1200°C or higher and the rate of rise to temperature is extremely rapid. From the work of May and Turnbull5 and from unpublished work, it was known that isothermal annealing near 1200°C tends to reduce the extent of secondary recrystallization and that a much weaker cube-on-edge texture results if appreciable normal grain growth replaces secondary recrystallization. Koh and Dunn6,7 have obtained additional information on complex primary recrystallization textures from further studies made after normal grain growth. In these instances the initial textures were retained during normal grain growth. A similar result reasonably could be expected in the present study except for the presence of a grain growth ihibitor1-5,8,9.21 and its tendency to allow only a few grains to grow. However, any information on the orientations of grains in the special annealing texture, even if far from representative of the initial matrix texture, would provide useful information on the nature of the matrix texture. In the present texture study the method of Newkirk and Bruce,10 which is based on the methods of Geisler" and Schwartz, 12 is used to obtain a complete (110) pole figure of the primary recrystallization texture. The high-temperature annealing texture is determined simply from the orientations of a large number of selected grains. The kinetic nature of the process that produces the annealing texture is treated elsewhere13 and it is shown that a form of secondary recrystallization with a very high rate of nucleation occurs during rapid annealing at high temperatures. EXPERIMENTAL PROCEDURE Commercial 0.014-in. cold-rolled silicon iron strip (3.16 wt pct Si), prepared by two stages of cold rolling with an intermediate short anneal, was given a decarburizing 3-min anneal at 800°C. Me-tallographic studies indicated complete recrystallization. Short-time anneals at 900° C and at higher temperatures proved that secondary recrystallization had not begun at 800°C, in fact, the short additional anneals were still in the induction period of secondary recrystallization. A rapid rise to an annealing temperature of 1260°C (2300°F) was obtained in a BaC12and NaCl fused salt bath. The structures that resulted from anneals in the range 12- to 1000-sec duration were relatively finegrained, even though the growth was a form of exaggerated grain growth13 or secondary recrystallization with a high nucleation frequency.= Many of the grains were large enough for an X-ray study using a 5-mil X-ray beam. A transmission Laue Camera and an optical-mechanical stage for moving the grains into the X-ray beam were used. A total of 325 grains were X-rayed in this manner and the grain orientations determined. Complete (110) pole figures were obtained for the primary recrystallization texture using CoKa radiation at 30 kv in the back-reflection range, such as (220) for (110) poles, as described recently by Newkirk and Bruce.10 The low voltage serves to reduce the spurious white radiation to a minimum. A filter of 0.001-inch iron foil was located in front of the detector slit for transmission and in front of the beam slit for back reflection. A new and improved specimen holder extended the useful tilting angle range for transmission to 70 deg instead of 60 deg as previously reported.' A torque magnetometer was used to obtain the magnetic torque curves for a number of l-in. diam disk specimens. RESULTS The (110) pole figure of the material after recrystallization at 800°C is shown in Fig. 1. The positions of the pole concentrations are found to be

Jan 1, 1961

By Robert L. Taylor, Richard E. Goodman

A complete rational analysis for design of excavation slopes and loaded rock masses is a desirable but perhaps unattainable goal. Irregular external and internal boundary conditions, poor understanding of failure criteria for large masses of rock, capricious material properties, and the importance of indeterminate forces and inaccessible and virtually unsampleable rock defects emphasize the importance of experience in this aspect of rock engineering. The experience must be correlated with geological factors. In certain regions the accumulation of such experience through the observation of existing rock slopes in various formations constitutes an important aspect of studies for design of rock excavations. In former times an accepted method of rock construction consisted of trials and adjustments. This approach is not often compatible with present methods of contract management. With the development of improved instruments and warning devices such as inclinometers, piezometers, relays, stress meters, and rock noise detectors, modified trial procedures of rock construction may reappear in specific applications. In spite of the great advances made, development of methods to predict the performance of rock slopes, abutments, and foundations deserves vigorous effort. Two distinct approaches may be taken. The rock mass in question may be considered a continuum and the stresses and strains throughout the region of influence of the work may be calculated. Or, the rock mass may be described as a discontinuum whose stability calculation involves the statics and kinematics of accumulations of rigid blocks. The prototype must lie in the range between these contrasting models. As yet, however, there is little reconciliation between the two methods

Jan 1, 1967

By T. S. Fuller

MUCH study has been given by engineers in general, and investigators in particular, to the concentration of stress which occurs under load in structural members having irregularities in section such as notches, shoulders, key ways, tool marks, etc. The result of the effect of both fresh and salt water corrosion upon the endurance properties of various metals and alloys has been ably determined and the general laws underlying these phenomena carefully pointed out by McAdam. From a practical standpoint, 'however, it is after all the endurance value of corroded, non-symmetrical sections which is most pertinent. In the experiments about to be described rotating cantilever specimens of nickel steel of the 3.5 per cent nickel ' 0.35 per cent carbon type have been used. These were machined from bars l 1/8. in. dia. and 9% in. long and were heat-treated by quenching in oil from 825 deg. C. followed by reheating to 650' C. and oil quenching. The tensile and impact properties of this material so heat- treated follow:

Jan 1, 1931

By I. B. Cadoff, J. C. Bilello, R. Rosenberg

Diffiusion of magnesium into the surface of LiF crystals to controlled depths and subsequent heat treatments provided a wide range of surface zone harahesses and structure, The bend strength of the LiF crystals was increased by as much as an or-dev of magnitude. Ductility was achieved when dislocation generation occurred in the diffusion zone or when dislocations penetrated to the surface from the intevior. A critical surface hardness of 130 to 140 kg per sq mm was found helozu which generation could take place in the diffusion zone and ahoue which the zone was impenetrable, This hardness was obtainable by several methods, among them the aging of quenched MgF2 -LiF solutions to produce MgF, precipitation. Maximum hardness was ohtained in quenched specimens with no visihle evidence of MgF,. Diffusion-zone formation followed a parabolic rate law and an activation energy of 20.9 kcal per mole was obtained for the process. RECENTLY, the properties of ionic crystals as related to surface condition have been receiving much attention, specifically the transitions between ductile and brittle behavior. Originally Joffe 1 showed that NaCl crystals could be made ductile by immersion in water and related this to the elimination of surface microcracks. Aerts and DeKeyser 2 and Gorur 3' have subsequently shown that ionic crystals are inherently ductile and are embrittled through contact with air. Machlin and Murray4 hypothesized that a layer of NaCIO3 produced by contact of ozone with NaCl induced embrittlement by acting as a barrier to outward dislocation flow. westwood,' Rosenberg and Cadoff,9 and Bilello and cadoff' have reported surface strengthening of LiF crystals by coating with a magnesium compound and then heat treating for adherence. The major effect of the coat was to inhibit dislocation-slip lines from reaching the specimen surface. westwoods showed microcrack formation and fracture to be caused by slip-band interactions at the surface. The material presented in this paper is an extension of the work reported earlier by Bilello, Rosenberg, and cadoff'6,7 and illustrates the wide range of surface properties and bulk behavior obtainable by use of heat-treated magnesium-diffused surface regions in LiF crystals. EXPERIMENTAL PROCEDURE The LiF single crystals were obtained from the Harshaw Chemical Co. Some batch to batch variation was observed; therefore all specimens for a given test series were cleaved from the same crystal. The typical dimension used was 1 by 0.1 by 0.40 in. Surface damage resulting from cleavage was removed by chemically polishing in a 2 pct NH4OH solution. Each group of specimens was given a vacuum anneal at 700°C for 4 hr to provide a base standard for measuring comparative effects of various surface treatments. To produce the reacted surface zone, the annealed specimens were immersed in a boiling suspension of MgF, in doubly distilled HzO, agitated slbwly for 30 sec, removed, and dried at room temperature. Uniform coatings of MgF, were deposited with a thickness of approximately 5 mils. It should be noted that this technique can be modified for use with crystals which are soluble in water by using boiling absolute alcohol as the dissolving medium. This was found effective for the coating of NaCl with MgF2. The diffused surface zone was obtained by annealing the coated samples at elevated temperatures in a vacuum of lob4 mm Hg. Penetration depth was controlled by varying the annealing time from 1/2 to 28 hr. After heat treatment, the samples were tested for bend strength and hardness. Load was applied by four-point bending in a hard-beam testing jig. Four-point rather than three-point bending was used to provide a wide area of constant stress and to minimize the effect of localized inhomogenities in the specimen. The deflection rate was 8 x min-' and the distance between knife edges was 1/4 in. Load-time curves were obtained from a chart recorder coupled to the machine and converted to resolved shear stress on the shear plane vs deflection, as plotted in the figures. The unstressed portions of the sample outside of the two outer knife edges were used for the microhardness studies. Microhardness measurements were made with a Bergsman tester attached to a Reichert metallograph. All hardness impres-

Jan 1, 1964

By A. L. Field, P. H. Royster

Bureau of Mines Technical Paper 189 consists of a record of the scientific data obtained in the iron blast-furnace slag investigation which is reported in Technical Paper 187, "Slag Viscosity Tables for Blastfurnace Work." It includes a description of the method of preparing the synthetic melts, construction of an improved electric furnace, and refinements in laboratory methods of measurement. Only the general features of the work and the conclusions drawn from the experimental data can be given attention here. Silicates in the Liquid State In the manufacture of refractories, Portland cement, glass, and porcelain, and in pyrometallurgical operations, importance attaches to the behavior of-silicate compounds at temperatures beyond the range of common experience. This field of research has not been investigated as carefully as its scientific and industrial importance would seem to warrant. Probably the most important of the unsolved problems in the chernistry of silicates is the question of their stability in the liquid state. That little progress toward the solution of this problem has been made is not strange if there be borne in mind the difficulties attending experiments made at temperatures at which silicates become fluid, and the comparatively short time since it became possible to measure these temperatures. On the other 'hand, considerable progress has been made in the study of the compounds in the solid state because of the directness and simplicity of methods of optical examination. Important advances have been made by the Geophysical Laboratory at Washington in recent years. An extended study has been made there of saturated solutions representing a considerable number of binary and ternary systems of the more common refractory oxides. The methods

Jan 1, 1918

By Wallace Ralston

The East Texas district includes the northeast 38 counties of the State of Texas. It still remains one of the most important oil-and-gas-producing areas of the United States, since it includes within its boundaries the large East Texas field. Other fields of importance are: Van, Rodessa, Talco, Cayuga, Long Lake and Sulphur Bluff. Production is from the Nacatoch, Blossom, and Woodbine of the upper Cretaceous and the Paluxy and Glen Rose of the lower Cretaceous. Of these, the Woodbine is the most important, since it is the producing horizon iri the East Texas field. Fields East Texas Field.—There were 2471 oil wells, 1 gas well and 84 failures completed during the year of 1936 in the East Texas field; that is, 1565 fewer than in the year of 1935. The total number of producing wells is now 22,031, of which 50 are temporarily shut down; 18,435 wells flowing their production; 3150 pumping; 293 on gas-lift, and 82 operated by other methods. This shows an increase of 1642 wells on artificial lift over Jan. 1, 1935. The average daily salt-water production is estimated at 42,700 bbl. from 2327 wells—an increase of 1201 wells over the year of 1935. The field is now drilled to an average density of one well to 5.85 acres. Average bottom-hole pressure has dropped from 1193 Ib. to 1168 lb., approximately 1 lb. drop for each 6,600,000 bbl. of oil produced. During the month of December 1936, the estimated daily average production of illegal oil had dropped from 20,500 bbl. in December 1935 to 7500 bbl. The commercial gas production is of minor importance in the East Texas field, and figures for the amount of gas taken from the field are not available at the present time. Talco Field, Titus and Franklin Counties.—The discovery well was drilled by Housh, Thompson et al. on the C. M. Carr tract and completed in March 1936, as a pumping well making 552 bbl. per day of 24' gravity oil. This well was first completed at a total depth of 4208 ft., the top of the sand being 4190 ft. Later it was deepened to 4260 ft., which increased the production from 552 to 725 bbl. per day. This field is producing

Jan 1, 1937

By S. G. Gibbs

A new method for predicting the behavior of sucker-rod pumping systems is presented. The pumping system is described by a flexible mathematical model which is solved by means of partial diflerence equations with the aid of computers. Polished rod and intermediate-depth dynamometer cards can be calculated for various bottom-hole pump conditions. The technique permits simulation of a wide variety of operating conditions, both normal and abnormal. The data generated with the new technique are useful in refining the criteria for design and operation of sucker-rod systms. INTRODUCTION Sucker-rod pumping systems are used in approximately 90 per cent of artificially lifted wells. In view of this wide application, it behooves the industry to have a fundamental understanding of the sucker-rod pumping process. Oddly enough, our understanding has been rather superficial. This is evidenced by the semi-empirical formulas which have been used as the basis for design and operation of sucker-rod installations. Thoueh- we have realized the limitations of our methods for many years, it has not been computationally feasible to use more refined techniques. With the advent and widespread use of digital computers, it is now possible to handle the mathematical problems associated with sucker-rod pumping. This paper summarizes a computer-oriented method which can provide greater insight into the sucker-rod pumping process. It is hoped that this technique, and techniques which may evolve from it, will prove to be the tool needed by industry to obtain the most efficient use of rod pumping equipment. THE MATHEMATICAL MODEL Prediction of sucker-rod system behavior involves the solution of a boundary value problem. Such a problem includes a differential equation and a set of boundary conditions. For the sucker-rod problem, the wave equation is used, together with boundary conditions which describe the initial stress and velocity of the sucker rods, the motion of the polished rod and the operation of the down-hole pump. Of these items, the wave equation, the polished rod motion condition and the down-hole pump conditions are of primary importance. Discussion of the mathematical model centers about these factors. ROD STRING SIMULATION WITH THE WAVE EQUATION The one-dimensional wave equation with viscous damp- is used in the sucker-rod boundary value problem to simulate the behavior of the rod string. This equation describes the longitudinal vibrations in a long slender rod and, hence, is ideal for the sucker-rod application. Its use incorporates into the mathematical model the phenomenon of force wave reflection, which is an important characteristic of real systems. The viscous damping effect postulated in Eq. 1 yields good solutions, even though nonviscous effects such as coulcomb friction and hysteresis loss in the rod material are present. Fortunately, the nonviscous effects are relatively small, so the viscous damping approximation used in the wave equation is adequate. The coefficient v is a dimensionless damping factor which is found in field measurements to vary over fairly narrow limits. For mathematical convenience the gravity term is omitted in Eq. 1. The effect of gravity on rod load and stretch can be treated separately, as will be noted later. Since Eq. 1 is linear, the legitimacy of this procedure is easy to demonstrate. POLlSHED ROD MOTION SIMULATION The motion of the polished rod is determined by the geometry of the surface pumping unit and the torque-speed characteristics of its prime mover. By determining the motion of the polished rod, we formulate an important boundary condition. From trigonometrical considerations it can be shown that the position of the polished rod vs crank angle 0 is given by (see Fig. 1) These equations are obtained from the general solution of the "four-bar" linkage problem and can be used to describe the kinematics of any modern beam pumping unit.' If prime mover speed variations are disregarded, the angular velocity of the crank is constant, and Eq. 2 can be used to predict the position of the polished rod vs time. However, the constant-speed condition leading to constant crank angular velocity is only approached in practice: hence, it is better to make provisions for prime mover speed variations in the mathematical model. The speed at which the prime mover runs is determined by its torque-speed characteristics and the torque imposed upon it. The torque that the prime mover "feels" is the net torque arising from the polished rod load and the opposing torque from the counterbalance effect. The

By Darrel W. Hansen

Morrow Point Dam and Power Plant are principal features of the Bureau of Reclamation's Curecanti Unit of the Colorado River Storage Project. They are under construction on the Gunnison River 20 miles east of Montrose, Colo. Johnson-MK is the prime contractor, and represents a joint venture of Al Johnson Construction Co., Minneapolis, Minn., and Morrison-Knudsen Co., Inc., Boise, Idaho. The power plant will be housed in an underground chamber in the left abutment, approximately 250 ft behind the original canyon wall. The chamber is 206 ft long and 57 ft wide. The distance from the foundation to the spring line of the roof arch varies from 51 ft in the service bay to 120 ft in the control bay. The roof arch has a rise of 16 ft. The longitudinal center line of the chamber is orientated east-west with the draft tubes discharging nearly due north. Access to the power plant chamber was possible through the cable tunnel, access tunnel, two draft tube tunnels, two penstock tunnels, exploratory tunnel, which became the ventilation tunnel, or the grouting and drainage tunnel leading to the dam. (See Fig. 1.) The shortest and fastest access was through the cable and access tunnels, and the contractor drove these two tunnels simultaneously. The cable tunnel and cable gallery excavation exposed a transverse section, at the west end of the chamber, that was 15 ft wide and extended from the crown to 5 ft below spring line. It was here that arch excavation began. The first 34 ft of advance along the arch was driven on three headings, and the muck was removed through the cable tunnel. Meanwhile, the access tunnel was completed, and a raise was driven from its crown to intersect the advancing arch excavation near the longitudinal centerline

Jan 1, 1968

Operating Characteristics of Centrifugal Fans and Use of Fan Performance Curve Discussion of paper by. Louis W. HUBER, presented at the New York Meeting, 1926, .and issued, as Pamphlet No. 1542-A, with MINING AND METALLURGY, February, 1926. G. BRIGHT, Pittsburgh, Pa.-Apparently from the pressure curves for a forward-curved-blade fan, in Mr. Huber's paper, practically all ventilation-might be stopped with increased resistance. In order, to discuss the characteristics of a fan we need, some better way to measure the characteristics of a mine. You all know that. the average anemometer is not very-reliable. Sometimes two anemometers, supposed to be recently calibrated, will differ 50 per cent. Either this or some other committee should standardize measuring methods. The characteristic curves of fans, given by Mr. Huber, would indicate that the forward-curved-blade fan would cause trouble in attempting parallel operation, because two machines will not parallel unless they have dropping pressure characteristics. On the other hand, it is indicated that with the backward-curved blade, they could easily be paralleled. But few mines use more than one fan. Mr. Huber said that if the resistance of the mine was considerably more than contemplated, the quantity of air might be such that the efficiency of the backward-curved fan would be seriously affected, dropping say from 70 to 55 or 50 per cent. In such event, could a difference of speed be selected for the fan that would give the quantity desired at a higher efficiency? L. W. HUBER, Pittsburgh, Pa.-The backward-curved-blade fan responds to change in speed the same as any other fan; if' the speed is doubled, the quantity of air is doubled, the pressure is increased four times and the horsepower eight times. One point not mentioned in the paper is that the backward-curved fan is more efficient than the forward-curved or any other type. If the latter were more efficient, it would pay to install that type and keep the resistance of the mine constant, which is hard to do but it can be done with care. But the total mechanical efficiency of a fan with backward-curved blades is from 10 to 20 per cent. higher.

Jan 1, 1927

By Carolyn Barnes

The Offshore Technology Conference, the world's largest technical conference and exhibition on the development of offshore resources and protection of the ocean environment, is sponsored annually in Houston, Texas, by 12 international engineering and scientific societies. This year's OTC, the seventh, will be held May 5-8 at the Astrodomain, and will be the largest in its history. The technical program for the first meeting in 1969 consisted of 100 papers, an exhibit display of 380 booths, and an attendance of 4300. This year. 280 technical papers are to be presented, and more than 2800 exhibit booths, representing some 1200 companies and nine countries, will be on display for an anticipated audience of 40,000.

Jan 4, 1975

By Fred McConnell

FROM beginning to end, the processes of coal stripping are of great interest. From the time the prospector enters upon the property to examine it and to prove it, until the coal is loaded into railroad cars, every step must be taken with careful thought and planning. In proving the merits of a prospective property, an examination and computation of the overburden is of almost equal importance to the determination of the extent and quality of the coal bed itself. Is the overburden hard, and will it require drilling and shooting? How many yards of it will have to be handled to produce a ton of coal? Will it remain in place when .put in the spoil bank, or will it spread and run back into the pit? Are the drainage problems serious, and what will it cost to handle the water? Does the coal have bad dips, and what will be the grades and curvatures for haulage? These are a few of the physical problems that confront the prospector, and they can be ascertained only by adequate and careful drilling and engineering of the property to be considered. The engineer is an ever-present necessity, not only in the prospecting but in the daily operation of the property after it has' been approved and developed. The first step in operation after the location of the tipple is the contouring of the surface to be stripped and the laying out of the pits for operation, having in view again adequate room for spoil, drainage, haulage and other problems. If the overburden is hard, as much of it is in the larger stripping areas, it must be drilled for shooting with churn or well drills, the holes continuing from the surface down to or near the coal bed. The location of these holes should be made, and marked with stakes, by the engineer, acting in conjunction with the shooting foreman. The usual practice is to drill holes 6 in. in diameter, although the present tendency is to increase the diameter of these holes so that they will hold, without springing, a larger charge of explosive. With the use of the old method of shooting, the holes were sprung or chambered several times with charges of dynamite, and in the cavity thus made, the explosive was placed, largely at the bottom of the hole; but with the use of liquid oxygen as an explosive, and with the later

Jan 1, 1931

By E. N. Silverman

Mixtures of' MnS, ZFeO-SiO,, ZMnO.SiO, FeO, and MnO were prepared synthetically and used to study the planes ZFeO. Si0,-ZMnO.SiO,-MnS, FeO-MnO-MnS, and Fe0-MnO.Si0,-MnS in the quaternary system. Because the oxides and silicates studied flux MnS, inclusions in this system are partly liquid during rolling. Also, oxygen can modify subsurface inclusions through the reaction MnS + FeO—FeS + MnO during the soaking of ingots and the reheating of blooms and billets. NONMETALLIC inclusions in steel have long been a subject of study and conjecture because the properties of many steels are known to be affected by the the kind and amount of inclusions present. In free-machining steels, the type of inclusion present has a direct bearing on their machinability; in other steels, cleanliness is important and metallurgists direct their efforts at reducing the amount of non-metallic inclusions. Thus, the accumulation of knowledge about the formation and behavior of inclusions during all stages of steelmaking and processing should aid in improving the quality of steels and decreasing the production costs resulting from rejections. Previous studies of inclusions have contributed greatly to our understanding. The investigators have generally examined inclusions in finished steel. Boulger, Moorehead, and Garvey1 found that in Bessemer steels, low silicon contents results in globular sulfide inclusions with attendant high machin- ability ratings. Van vlack2 also found that low silicon contents favor inclusion morphology that contributes to high machinability ratings. Boquist and Stoll* found that silicon content affected sulfide inclusions and machinability of blooms, billets and bars more than did the finishing temperature in the range between 1775° and 2075°F. Carney and Rudolphy3 studied the distribution of sulfur, manganese, silicon, and carbon in a commercial ingot of resulfur-ized steel and found that silicon was concentrated near the bottom. This helped to explain why bottom cuts had poorer machinability. Klinger and Koch4 developed techniques for extracting inclusions from steel, and the technique devised by Gurry, Chris-takos, and stricker5 for extracting carbides can also be adapted to the study of inclusions. A different approach to the study of inclusions in steel consists of synthesizing the constituents that form inclusions and determining the phase eauilibria in the system that contains the constituents. The resulting phase diagrams can then be used to determine the effect of the various constituents upon each other. In this way, it becomes possible to under-

Jan 1, 1962

By Donald O. Rausch, Adolph Soderberg

4.1-1. Introduction. Open pit mine planning must be correlated to all phases of a mining operation. The factors that must be considered in planning an open pit mine are numerous and must reflect the characteristics and surrounding conditions of a particular orebody. Therefore, only an outline of the subject can be presented here to aid the planning engineer in pointing out procedures that are generally applicable to pit design. The presentation is directed toward the planning of an open pit copper mine, but the procedures discussed should apply in most cases to any type of metallic or nonmetallic orebody. In planning an open pit mine the pertinent elements that must be included are: assays, geology, tonnage and areal extent of ore reserves, topography, mining equipment, economic factors of operating costs, capital expenditures, profit, types of ore, pit limits, cut-off grade, stripping ratio, rate of production, pit slopes, bench heights, road grades, ore metallurgical characteristics, hydrological conditions, property lines, and marketing considerations. 4.1-2. Sampling. Sampling must be adequate to classify the various materials to be removed from an open pit mine. Drillhole assays are plotted on sections and plan maps with ore and waste blocked out by selected bench intervals. These maps are prepared to depict the geological and other conditions existing on each mine level. The confidence factor to be applied to sampling and the resultant assays values must be given careful consideration. In uniformly disseminated de- posits, the confidence factor will approach unity. For widely fluctuating values, the average assay values should be discounted somewhat, the degree depending upon such factors as drillhole spacing. Such samples, at best, represent a very few pounds for hundreds to thousands of tons of ore

Jan 1, 1968

By F. E. Bash

WHENEVER electric and open-hearth steel men discuss the relative advantages of their respective methods, the question of temperature is always discussed, so that this paper is written in the hope that definite data may settle some of the questions and encourage further investigations along these lilies. The writer has had the opportunity of taking the tapping temperatures of steel from electric furnaces of different sizes in various plants and from a number of open hearths handling the same kind of steel. All temperature measurements were made with the same disappearing-filament type optical pyrometer and the corrections for emissivity applied were those worked out by Burgess,1 which are 0.40 for steel streams and 0.65 for slag. The correction is applied by calculating the curve giving the relation between the true and apparent temperature in the following formula: Log E = CZ log e( 1 _ 1 x \T2 T1) in which E = emissivity; C2 = 14,500; e = base of Napierien logarithms; ? = wave-length of light used = 0.65/4; T2 = true temperature, in degrees absolute; T,1 apparent temperature, in degrees absolute. The curve showing the relation between true and apparent temperature for steel and slag arc given in Fig. 1. For the purpose of comparison of open-hearth and electric furnaces, there are given in Table 1 the tapping temperatures of two 25-ton Heroult electric furnaces and one 6-ton with one 50-ton acid, one 40-ton basic, and one 65-ton acid open-hearth furnace, all making nickel ordnance steel for guns. The two 25-ton Heroult electric furnaces were finishing steel refined by the triplex process and the 6-ton Heroult finished steel that was partly refined in an open hearth.. In this table, the tapping temperature and the temperature of the steel stream into the first ingot

Jan 9, 1919

By Edward Wisser

The environment of an ore body is taken to mean not only its physical surroundings but every factor, passive or active, that conditioned the ore shoot, saving only the original composition of the solutions that formed the shoot. Collection of data related to the shape and characteristics of veins should be followed by correlation of the data and the formulation of generalizations regarding ore formation. The nature of the criteria used in arriving at these generalizations is discussed. Certain of the criteria, when used with an understanding of their underlying causes, become "ore-guides." In the course of his study the geologist must not confine himself to the immediate surroundings of the veins, but should attempt to work out the geologic history of events culminating in the crucial epoch for any mining district, the period of mineralization. The work may involve study of features far removed from the veins and related to them only indirectly. It commonly means thorough study of the geology of the entire region surrounding the ore deposits. THE following question has been suggested for discussion: ? "Are there any criteria by which one can determine when mining operations have reached the roots of an ore deposit?" The question deals less with the roots of a particular ore body than with the lower limit of the vertical range within which ore bodies may be expected. It concerns a critical line upon the longitudinal vertical projection of a vein. ? Below this line it is useless to look for ore shoots; above the line exploration below the bottoms of individual ore shoots may be justified. Can we learn to determine the position of such a line?

Jan 1, 1939

In 1776 two Franciscan friars, Dominguez and Escalante, started to find a direct route from Santa Fé to Monterey, and in their misguided wanderings northward they reached Timpanogos, now known as Utah lake, where they heard of a much larger body of water to the northwest, of which they were told that it was extremely salt.* They never saw this great lake, because they passed south of it on their way to the Pacific coast. The Dead Sea of North America was discovered in 1835 by James Bridger, a trapper. He and other trappers had ascended the Missouri and had reached the Bear river. A discussion arose as to the course of this river, and a bet was made, to settle which Bridger followed the Bear river to its source, in the Uintah mountains, and from the crest of the watershed he caught sight of the lake, to which he then descended.† He tasted the briny water of the inland sea and wondered if it were an arm of the Pacific Ocean. The lake was first seen by the Mormons on July 24, 1847. A band of them, numbering 145 and led by Brigham Young, had migrated from Missouri in search of a new home in the western wilderness. It is recorded that when Brigham Young stood on the summit of the pass over the Wasatch range and saw the valley of the Jordan outspread before him, he exclaimed: "It is enough. This is the right place". He had seen it in a vision, so he claimed, and foresaw the future glory of the new Zion that was to be planted in that happy

Jan 1, 1932

By O. C. Ralston

The use of copper sulfate for improving the flotation behavior of sphalerite is probably at least 15 years old. The original discovery of its activating influence is somewhat obscure. The story goes that in the mill at Mascot, Tenn., its favorable action was discovered by accident, early in 1914, as follows: The original laboratory test work on a sphalerite ore gave favorable flotation results, but after a mill had been built the flotation concentration of the ore was very unsatisfactory. In diagnosing the probable reasons, one fact pointed out was that the laboratory test machine had been constructed of bronze whereas the commercial machine allowed pulp to come in contact only with wood and iron. A plate of sheet copper was hung in the flotation machine and results immediately improved. At first fanciful explanations of electrolytic and electrostatic behavior were given credence, but when the copper plate was removed and a small amount of copper sulfate substituted in the pulp an even more favorable result was obtained. Toward the end of 1914 copper sulfate was also adopted in the acid flotation circuit of the Butte and Superior Copper Co. Just who is responsible for the original discovery the present writers do not know. It seems strange that in that era of flotation litigation this discovery was not patented. While for pragmatic purposes it [nay be sufficient to know that the mere addition of copper compounds to a flotation pulp is sufficient to activate the flotation of the sphalerite, for scientific purposes it is quite desirable to know more about how the action takes place. It is the purpose of this paper to present certain evidence dealing with the mechanism of the beneficial effect. The description of the effect as activation in contradistinction to depression is now common in both the English and German languages. It makes no assumptions as to whether the zinc sulfide surfaces have been filmed with copper compounds. In fact, the principal differences of opinion expressed in the literature deal with whether there is an actual formation of CuS (or even Cu2S) on the surface of the sphalerite. Activation of sphalerite takes place in alkaline, neutral or weakly acid solutions and whereas the present day flotation of sphalerite is usually in ah alkaline solution, the early use of copper sulfate was in a sulfate solution.

Jan 1, 1930

By Alexander L. Holley

The 400-ton testing machine, ordered in June, 1875, by the United States Board appointed to test "iron, steel, and other metals," has lately been completed at the Watertown Arsenal, thoroughly proved and accepted by the Board. The excellence of the machine in every respect is more than satisfactory, and its accuracy is at first sight astonishing, although an investigation of its principles must show that if the weighing apparatus will weigh at all, it must do so with perfect accuracy, because all its movements are absolutely without friction. The proof experiments were numerous, and the effects of recoil after sudden ruptures at maximum loads, were watched with great care, but without much anxiety, because the weighing parts affected are by no means delicate in structure, and their motion is almost infinitely small. Among the tests were the following : A forged link of hard, wrought iron, 5 inches in diameter between the eyes, was slowly strained in tension, and broke short off with a loud report at 722,800 pounds. The diameter before breaking at the point of fracture was 5.04 inches; after breaking, 4.98 inches. In order to see if the weighing parts had been disturbed by the recoil, which was obviously near the greatest recoil the machine will ever suffer, a horse-hair was next tested; it was 7-1000ths of an inch in diameter; it stretched 30 per cent., and broke at 1 pound. Other horse-hairs vary in tenacity between 1 and 2 pounds. Of course, the accuracy of the machine on such delicate specimens, and indeed on specimens having some hundreds of pounds tenacity, has been checked and proved by other weighing machines. A 5-inch round bar, turned down to 38 inches diameter along the centre, was pulled apart at 430,200 pounds tension. Then some more horse-hairs were tested ; also copper wires 191/2-1000ths of an inch in diameter, which averaged 25 pounds tenacity..

Jan 1, 1879

By Plato Malozemoff, A. M. Gaudin

IN modern practice the major portion of an ore is reduced to flotation size by fine grinding. As the result of grinding fine enough to liberate most of the minerals, a substantial portion (generally 5 to 15 per cent) of the ore is inadvertently reduced to a size much finer than that necessary for liberation. This portion of most flotation pulps is very refractory to recovery by flotation. A reduction of one-quarter or more in recovery in this range of extremely fine particles can be observed. The loss in metals caused by overgrinding is appreciable. That this loss is characteristic of very fine particles has been suspected for some time;(l)† however, it was definitely quantified only recently.(2) Definite reduction in float-ability with reduction in particle size beyond a critical size of maximum floatability can be accepted now as an established fact. Formulating the Hypothesis In looking for the cause of the ill behavior of the finest particles it may be well to consider the essential differences between fine and coarse particles. A difference that immediately comes to mind is their intrinsic difference in size and consequently in relative extent of surface. If one agrees that attachment of mineral particles to bubbles must follow direct encounter of particles with bubbles one is forced to conclude(3) that the probability of encounter between a mineral particle and a bubble varies directly as the size of the particle, provided the particle is small compared to the bubble. In other words, the finer the particle the poorer its chance of being recovered in a given time of flotation. There is an effect, implicit in this theory, which should overcome the effect of excessive fineness of the particles; namely, flocculation of the particles. The floccules can be conceived as being simply larger particles and therefore capable of becoming attached to bubbles. And, indeed, in all the cases in which a sulfide mineral of near-colloidal size was successfully floated the mineral (but not necessarily the gangue) was flocculated. Moreover, it was shown experimentally(4) that galena previously flocculated by inorganic flocculators and then added to gangue

Jan 1, 1935