Search Documents

By J. W. Spretnak, D. A. Chatfield, G. W. Powell, J. R. Eifert

In nzost cases, the driving force for a lattice transformation is produced by supercooling below the equilibriunz transformation temperature. The interfnce reaction in isothermally annealed, multiphase diffusion couples may involve a luttice transformation which also requires a driving force. Direct experinzental evidence has been obtained for the existence of the driring force in the form of a supersaturated phase at the aocc)-0@cc) interface in Cu:Cu-12.5 ult pct A1 couples; the super saturation is equivalent to an excess free energy of approximately 3 cal per mol at 905. A tentatiue interpretation of the dynanzic situation a1 the interface based on the free energy-composition diagram is proposed. THE presently accepted theory of diffusion in multiphase couples1 states that there will be a phase layer in the diffusion zone for every region which has three degrees of freedom and which is crossed by the diffusion path in the equilibrium phase diagram. For binary systems, this restriction excludes all but single-phase fields and, for ternary systems, only one- and two-phase fields are included. In addition, Rhines"~ as well as other investigators3 6 have reported that the compositions of the various phases adjacent to the interfaces are, for all practical purposes, the compositions given by the intersections of the diffusion path with the solubility limits of the single-phase fields of the equilibrium phase diagram. Some studies of the rate of thickening of these intermediate diffusion layers indicate that the thickness of the layer changes para-bolically with time, or: where x is the position of the interface relative to an origin xo, t is the diffusion time, and k is a temperature-dependent factor. crank7 shows mathematically that, if the compositions at an interface are independent of time and the motion of the interface is controlled by the diffusion of the elements to and from the interface, then the segments of the concentration penetration curve for a semi-infinite step-function couple will be described by an equation of the form: hence, Eq. [l] follows from Eq. (21 if the interface compositions are fixed and if the motion of the interface is diffusion-controlled. Although the concept of local equilibrium being attained at interfaces has assumed a prominent role in the theory of diffusion in multiphase couples, experimental evidence and theoretical discussions which challenge the general validity of this concept have been reported in the literature. arkeen' has stated that strict obedience to the conditions set by the equilibrium phase diagram cannot be expected in any system in which diffusion is occurring because diffusion takes place only in the presence of an activity gradient. Darken also noted that it is usually assumed that equilibrium is attained locally at the interface although the system as a whole is not at equilibrium, the implication being that the transformation at the interface is rapid in comparison with the rate of supply of the elements by diffusion. ISirkaldy3 indicates agreement with Darken in that he believes the concept of local equilibrium is at best an approximation because the motion of the phase boundary requires that there be a free-energy difference and, hence, a departure from the equilibrium composition at the interface. Seebold and Birks9 have stated that diffusion couples cannot be in true equilibrium, but the results obtained are often in good agreement with the phase diagram. The initial deviation from equilibrium in a diffusion couple will be quite large because alloys of significantly different compositions are usually joined together. Kirkaldy feels that the transition time for the attainment of constant interface compositions (essentially the equilibrium values) will be small, although in some cases finite. Castleman and sieglelo observed such transition times in multiphase A1-Ni couples, but at low annealing temperatures these times were quite long. Similarly, ~asing" found departures, which persisted for more than 20 hr, at phase interfaces in Au-Ni and Fe-Mo diffusion couples. Braun and Powell's12 measurements of the solubility limits of the intermediate phases in the Au-In system as determined by microprobe analysis of diffusion couples do not agree with the limits reported by Hiscocks and Hume-Rothery13 who used equilibrated samples. Finally, Borovskii and ~archukova'~ have stated that the determination of the solubility limits of phase diagrams using high-resolution micro-analyzer measurements at the interfaces of multiphase couples is not an accurate technique because of deviations from the equilibrium compositions at a moving interface; diffusion couples may be used to map out the phase boundaries in the equilibrium diagram, but the final determination of the solubility iimits should be made with equilibrated samples. The purpose of this work was to investigate the conditions prevailing at an interface in a multiphase diffusion couple and to compare the interface compositions with those associated with true thermodynamic equilibrium between the two phases. Microanalyzer techniques were used to measure interface compositions in two-phase Cu-A1 diffusion couples annealed at 80@, 905", and 1000°C for various times.

Jan 1, 1969

By Peter J. Szabo

INTRODUCTION The time period from the detailed feasibility study to the post investment audity usually ranges from three to eight years depending upon the nature of the mining project considered. It is the only after the post investment audit that we know the adequacy of the assumptions made concerning operational risk assessment in the detailed feasibility or acquisition economics. The post investment audit results from numerous mining projects can best be described by a verse by John Greenleaf Whittier's Maaud Muller. It reads "For all sad words of tongue or pen the saddest are these 'It might have been!"' Dissecting the negative results of numerous mining projects we find faulty assumptions concerning markets, geology, capital investment and operational risk assessment. Although in hindsight many of these assumptions could have been considered impossible or impracticle to have forecast with any degree of certainty, we find that refined assumptions concerning operational risk assessment could have been made with only a modicum of additional "Due Diligence". Anyone who invests in a mining property should employ a much higher discount rate of future cash flow, (usually in the minimum range of 25%-30%), than he would expect from such safe investments as Treasury Bills or high grade Utility Bonds. The nature of this steep discount translates to a large uncertainty concerning the timing and actualization of assumptions contained in the detailed feasibility study. We must remember that when a project gets beyond 20 years, any contribution to the value of the project of cash flow is minimal due to the nature of the discounting process. Thus for each full or partial day lost in the development or early operation stage of a project, the financial impact will be greater than similar lost days later on in the project. Adequate operational risk assissment is particularly critical when bidding on competitive tenders for coal deposists in remote locations such as the Bowen Basin in Queensland, Australia. Because of the market attractiveness of these coal deposits for supplying end users in the Far East, Middle East and Europe, state governments require competitive tender biddings via the Authority to Prospect process. Front end bonuses and super royalty payments must be commited before the actual mining conditions are known. Time to submit firm offers from the actual request for proposal vary from 90 to 120 days. Thus any operational risk assessment must be detailed, realistic and reflective of the actual project. When one searches the literature, one finds limited qualitative data on operational risk assessment in valuation papers. Usually this facet of valuation takes a secondary role to such areas as reserves, markets, and environmental considerations. When one comes to the question of operational risk assessment more often than not one finds the use of "rules-of-thumb", such as tons per man shift, average production, average seam height, etc., are used to forecast results on which banks and other financial institutions are required to make investment decisions. Because of the extremely competitive environment of the 1970's and 1980's numerous financial institutions approved loans without adequate "Due Diligence", and are currently paying a steep price in terms of non performing loans and charge offs. One must always remember that each operation is unique with its own characteristic

Jan 1, 1985

By Clyde E. Williams

Estimates indicate a life of known Lake Superior iron ore reserves of 20 to 30 years. Although some believe the future ore supply will come from foreign sources and will be brought to interior points via the projected Great Lakes-St. Lawrence waterway, and others fear a displacement of the interior steel-producing districts to the Atlantic seaboard, the author has faith that American engineering skill will make possible the use of lean ores from the Lake Superior district. Three general types of Lake Superior ores and ore formations, that represent possible reserves and require beneficiation, are: (1) the wash ores of the western Mesabi range, (2) the partly leached hematitic formations, and (3) the oxidized but largely unleached iron formations. The total tonnage represented by (1) and (2) is not large, but the recovery of iron from present washery tailings would bring on the market the equivalent of nearly one million tons of wash ore, annually. Group 3 comprises the magnetic iron formation of the eastern Mesabi range, the hematitic formations including the taconites of the Mesabi range, and the iron formations of all the other ranges. These formations represent our future supply of iron ore. Their treatment requires intensive research because the bulk of the iron oxide and silica minerals exist in a finely disseminated condition. The possibilities of the adaptation of tables, oil flotation, and other processes warrant extensive study. Cheaper method of agglomeration of the concentrate is essential. Recent developments in better preparation and sizing of blast-furnace charges indicate that substitution of agglomerated ore for fines will increase furnace efficiency and output. If agglomerated beneficiated ore can be shown to rate a per-unit premium for iron contents over the base rate or a premium for structure, the payment of these would greatly assist in enlarging our iron ore supply. Since present methods of taxation of ore reserves, which encourage the rapid depletion of rich ores, will result in using up our rich ores and later on putting domestic producers at a disadvantage in competing with' foreign producers, it would seem highly provident to conserve our rich ores and to increase the use of beneficiated ores as soon as possible.

Jan 1, 1931

By J. E. Jopling, J. R. Chenneour, E. L. Derby, S. R. Elliott

The Marquette range, on which are situated the iron mines of Mar-quette County, together with a few in Baraga County, Mich., extends from a point 10 miles southwest of Marquette westward for 30 miles. The tracts are usually a multiple of the standard 40-acre parcel, which is the smallest government subdivision of a square mile or section. About half of the mines are held in fee, these being owned by the older mining companies. Some of them date back to about 1880, and a few are as early as 1850. During the past 40 years most of the mines opened have been on leased lands, the royalty being either for a stated amount per ton or a percentage of the selling price of the ore at the lower lake ports, or the selling price on board of cars at the mine. The first merchantable body of ore discovered in the Lake Superior district was found, in 1845, at what is known as the Jackson mine, near Negaunee. This ore was hard hematite. After unprofitable attempts had been made, in 1848, to smelt it in forges, shipments were begun to lower lake ports, which increased rapidly upon the completion of the locks at Sault Ste. Marie, in 1855, and the railroad from the mines to Marquette, in 1857. Beginning with the Pioneer, in 1858, a number of small charcoal furnaces were built to smelt a part of the product. At various points in the upper and lower peninsulas, large charcoal furnaces are still making iron from the ores of the Marquette range. In connection with these furnaces are byproduct plants. As the deposits were opened up, soft ore was encountered, but for a few years this was disregaided, as only the hard ore was used. Underground mining was begun about 1880 and during the next few years the open-pit mines producing high-grade ore were exhausted. The first mines in the district were owned by the Jackson, Cleveland, Lake Superior, Lake Angeline, Champion, Iron Cliffs, Humboldt, Republic, and Michigamme companies. Many of these companies have been merged in the holdings of The Cleveland-Cliffs Iron Co., which controls most of the tonnage of the district.

Jan 1, 1925

By Charles C. Hawes

DETERMINATION OF SILICA OXIDE iron ores usually are found in intimate association with silica and phosphorus compounds. Their quantitative separation and purification sometimes present difficult problems to the chemist. Silicic acids may represent various degrees of dehydration. They are exeedingly weak, but combine with metallic oxides and form some of the most stable oxides in nature, the silicates. When iron ores are treated with hydrochloric acid, they yield practically all their iron. However, apart from rare exceptions, varying amounts of insoluble residues of silica, alumina, lime, magnesia and compounds of phosphorus, sulphur, titanium, chromium and others will be left. If the oxides of silicon, aluminum and titanium are present in small quantities, the insoluble residue is generally very small, but the presence of these oxides is more usual in larger quantities. Therefore, only a special treatment can break the bond between these elements. Ore Residues Acids remove the soluble constituent of the ore, leaving the insoluble residue, which chemically is rock or gangue and must be treated accordingly. Alkali carbonates are used frequently to break up the residue, but other fluxes have also been recommended, such as a number of lead and boron salts. The introduction 0f these salts, which offers certain advantages, requires, however, their removal before the other constituents can be analyzed, and this elimination is sometimes difficult. Usually in quantitative analysis silicates are dissociated by fusing them in a platinum crucible with sodium carbonate, thereby forming sodium silicate, Na2SiO3, sodium aluminate, Na2Al204, sodium titanate, Na2TiO3, and carbonates of other elements. All the carbonates are soluble in hydrochloric acid, but also some silicic acid is formed that must be rendered insoluble. To this end the solution is evaporated several times, as the first evaporation still leaves as much as 5 per cent of the silica soluble. Even after a number of evaporations, minute quantities of silica may be found with the iron and alumina present. Perchloric Acid as an Agent for Dehydrating Silicic Acid Perchloric acid, HC104, (60 per cent), has been used for years as a solvent, but few chemists have used it to dehydrate silica. It is derived from anhydrous perchloric C1207, which is most unstable and dangerous. Perchloric acid is a strong oxidizing agent, which boils at 203°C. It is more effective in rendering silica insoluble than any other known agent, and most rapid in action. After perchloric acid is added to a mixture containing silicic acid, the resultant solution is

Jan 1, 1945

By F. W. Schremp, V. L. Johnson

This paper discusses the results obtained from high temperature, high pressure filter loss studies in which field samples of clay-water, emulsion, and oil base fluids were used. High temperature, high pressure tests of some premium priced emrilsion and oil base drilling fluids show filter loss peculiarities that are not predicted by standard API tests. It is recommended that high temperature, high pressure filter loss tests be used to evaluate the performance of such fluids. Apparatus is described which proved to be satisfactory for evaluating filter loss behavior over a wide range of temperatures and pressures. INTRODUCTION The petroleum industry spends large sums of money each year on chemical treating agents for lowering filter loss and on premium-priced low filter loss drilling fluids. While it is an accepted fact that low filter loss is advantageous during drilling operations, it is questionable whether the present standard method of determining filter loss gives a reliable indication of the loss to he expected under bottom hole conditions. The purpose of this paper is to show that high temperature. high pressure filter loss tests Should be used to evaluate filter loss behavior of fluids for deep drilling. Concern over possible effects of filter loss on oil well drilling and well productivity dates back to the early 1920's. During the years 1922 to 1924, filtration studies were reported by Knapp,' Anderson2 and Kirwan." These studies were the first to be reported in the literature on this subject. No further information was published on the subject until 1932 when Rubel' presented a paper in which he discussed the effect of drilling fluids on oil well productivity. In 1935. .Jones and Babson constructed the first laboratory tester designed to study the effects of temperature and pressure on the filter loss behavior of clay-water drilling fluids. In a discussion of their investigations, Jones and Babsons stated, "Performance characteristics of a mud can he evaluated with considerable reliability by a single test at 2,000 psi and 200°F. Exact correlation between the results of performance test5 made under these conditions and the behavior of muds in actual drilling operations is of course impossible." Jones arid Babson apparently were well aware that at best laboratory tests can give only qualitative answers to the question of what is the actual behavior of a drilling fluid when subjected to deep drilling conditions. Jones' presented a paper in 1937 in which he described a static filter loss tester to be used for routine filter loss tests. This instrument subsequently was adopted as the standard APl filter loss tester. In 1938, Larsen7 developed a relationship between filtrate volume and filtrate time that is in general acceptance today. Larsen was cognizant of the danger of estimating bottom hole behavior from filter loss measurements at room temperature. He tried to predict the effect of temperature on filter loss by relating temperature effects through the temperature dependence of filtrate viscosity. This was undoubtedly an over-sirriplification of the temperature dependence of drilling fluid filter loss. In 1940, Byck" published a summary of experimental results of filter loss tests made on six representative California clsy-water drilling fluids. He concluded that "no existing method will permit even an approximate determination of the filtration rate at high temperature from data at room temperature. It is necessary to measure filtration at the temperature actually anticipated in the well, or to make a sufficient number of tests at various lower temperatures so that a small extrapolation of these data to the anticipated well temperature may be applied." Byck's findings were presuma1)ly well accepted and recognized by drilling Fluid technologists, and yet, they did not lead to wide adoption of high temperature drilling fluid filtration equipment. This is evidenced by the fact that no addition information has appeared in print on the subject since 194). Study of Byck's data shows that there was a useful consistency in them. The fluids did not show predictable losses at high temperatures, but they did line up at high temperatures in approximately the same order that they lined up at low temperatures. That is, if a fluid appeared to be a good fluid with relatively low loss at low temperatures, it would also be a good fluid with relatively low loss at high temperatures. In the last decade. the above situation has changed. The drilling fluid art is markedly different from what it was. The outstanding change, as far as the present discussion is concerned, has been the adoption of wholly new types of drilling fluids. Oil base and emulsion drilling fluids have come in to wide use. It is, therefore, necessary- to re-examine previously satisfactory generalizations to see if they are still valid. It turns out. as might have been expected. that Byck's explicit generalization. already quoted, is still true. Filter losses at high temperatures cannot be predicted from filter losses at low temperatures. However, no further generalizations are valid now. Fluids of different chemical types show different general behaviors. No longer do the fluids line up approximately the same at high temperatures as they do at low temperatures. They may line up entirely differently. Special fluids exhibiting very low loss at low temperatures may have losses as high as those of ordinary clay-water fluids at high temperatures. This fact is highly significant, because premium prices are being paid for the special fluids.

Jan 1, 1952

By D. Turnbull

RECENTLY it has been shown that aggregates of small liquid droplets of tin,' mercury' or gallium' kept from intercommunicating by suitable films do not solidify at an appreciable rate unless the supercooling is very much greater than that usually necessary to cause a large continuous mass of the metal to solidify. For example oxide-coated tin droplets1 (1 to 10 micron diam) must be supercooled 100" to 110°C before their rate of solidification becomes rapid, although large continuous masses of liquid tin usually begin to solidify when supercooled 30" or less." These experiments have been interpreted' on the hypothesis that nucleation of crystals in large continuous metal samples is almost always catalyzed by accidental inclusions. Therefore, if the metal is dispersed into a number of isolated droplets large in comparison with the number of inclusions, most of the droplets should not crystallize until a temperature sufficiently below the thermodynamic melt- ing point, T0, has been reached to permit an ap-preciable rate of homogeneous (noncatalyzed) nu-cleation. In general this temperature is very much less than the temperature at which the rate of heterogeneous (catalyzed) nucleation is appreciable. If this interpretation is correct then investigation of the kinetics of crystallization of small droplet aggregates should be one of the most fruitful methods of obtaining information about the homogeneous formation of crystal nuclei in liquids. In this paper the results obtained on gallium and mercury are reported more fully. In addition, results on the supercooling of aggregates of liquid bismuth and lead droplets are included. Experimental Procedure Some care must be exercised in the choice of a barrier to prevent the liquid droplets from coalescing lest the barrier itself catalyze the formation of crystal nuclei. From this standpoint, the most desirable barrier is vacuum or inert gas, but, because of the difficulty of experimental arrangement, solid compounds and adsorbed films have been selected. There are two guiding principles in the selection of compounds as barriers in addition to the requirement that they prevent coalescence of liquid droplets. First, the compound should be almost insoluble in the liquid metal and second, its lattice structure should be quite unlike that of the forming metal crystal. Even so, there is no a priori assurance that the solid compound film will not catalyze to some extent the formation of metal crystal nuclei. An adsorbed protective monolayer is less likely to be catalytic than a crystal compound film, but it is not often possible to find a monolayer that is stable under the experimental conditions. Also, it is desirable, though not generally essential, that the aggregate of droplets be prepared by breaking up the massive metal rather than from a powdered compound of the metal.

Jan 1, 1951

By Albert S. Trube

Increasing emphasis is being placed on the necessity for obtaining reasonably accurate estimates of the physical properties of reservoir fluids well in advance of more accurate laboratory data. One such factor is the isothermal coefficient of expansion of an undersaturated hydrocarbon liquid which may be contained in a particular reservoir. This coefficient, or liquid "compressibility", has often been assumed to be relatively insensitive and nearly constant. Although this assumption may be nearly correct in the case of high specific gravity liquids, it cannot apply in the case of medium to low specific gravity liquids. Any treatment of the nature of liquid compressibilities must give consideration to the variable nature of the isothermal expansion coefficient and the fact that it can be both pressure sensitive and temperature sensitive. The isothermal coefficient of expansion, or compressibility, of a substance is defined as -c = 1/V (?V/?p)T......(1) The value of Eq. 1 may be approximated for a finite pressure change by using the well-known relation, c = V1 - V1/Ve (p2-p1), ........(2) in which p1 > p1 and V2 > V2 and V1 + V2/2. The instantaneous compressibility may also be estimated from the slope of a curve on which log V is plotted vs pa. In this instance, it has been shown that c = In V1/V2/p2-p1 ...........(3) Eq. 3 may be used for variable compressibilities by plot-ting V vs p on semi-log paper. In this case, the instan-taneous or point compressibility is c = 2.303 m.......... . (4) in which m is the slope of the curve at a point in log cycles per psi. ISOTHERMAL COMPRESSIBILITY OF UNDERSATURATED LIQUID In the case of gases, the compressibility has been defined by Muskat' and others as Co = 1/p - ?z/z?p ..........(5) This was later generalized through application of the theorem of corresponding states' to co = 1/pr - (?z/z?pr) T8 ........(6) in which c, is defined as the pseudo-reduced compres-sibility and is numerically equal to (c.p,) and the sign is arbitrarily changed for mathematical convenience. Eq. 6 is general and applies to gases and liquids. In the case of liquids, c. = c1,pe, but if Eq. 6 is used, values of z and ?z/?p, must be determined for the liquid in question. The difficulty of obtaining accurate values of ?z/?p,, particularly in the region where T, is approaching 1.00, was pointed out in the previous paper'. This method of approach is unreliable for extension into computations of liquid compressibilities. On the other hand, c, can also be defined as follows: - Cr = 1/Vr (?Vr/?pr) Tr ......(7) and from which, Cr = 1/pr (?pr/?pr) Tr .....(8) In accordance with the theorem of corresponding states, Vr = V/Vr, p, = p/pr and pr = p/pr. Ref. 2 pro-vides an excellent source of reduced density, reduced pressure and reduced temperature data for a wide variety of fluids. For the purpose of this investigation, the set of fluids2 having ze = 0.27 was chosen because it in-cludes most of the heavier hydrocarbons usually found in those complex mixtures loosely defined as "reservoir oils". Data on undersaturated liquids in Ref. 2 were rearranged to conform with Eq. 8. To simplify the computation of cr, the isothermal p, data were plotted vs the log of pr, in which case for any straight line or tangent cr = 1/M pr pr .....(9)

Jan 1, 1958

By E. H. Burdick

THE difficulties inherent in table concentration operations as applied to gold, silver, lead and zinc ores, are accentuated in the scheelite mill, which has a flowsheet that is similar in general principles. The narrow "spread" in the specific gravity between scheelite and the usual gangue in which it occurs often makes its clean separation extremely difficult and in some cases impracticable. The problem is further complicated by the extreme friability of the mineral and its inordinate tendency to "slime," particularly where fine grinding is necessary and wet grinding methods are employed. The physical aspect of the occurrence of scheelite in the ores, the kind and character of the rock in which the mineral is present, its hardness, friability and the specific gravity of its constituents, as well as like characteristics of the associated mineral-spyrite, pyrrhotite, sphalerite, and others, all have a bearing on the successful milling of crude ores and the production of a concentrate that is marketable with minimum price penalty or none at all. Most tungsten deposits are considered low grade when the limiting factor of low percentage recovery by gravity methods is borne in mind. The great majority of deposits developed or in process of development carry from 0.4 to 1.0 per cent tungstic oxide. Ore carrying 1 per cent is considered good grade; 0.7 to o.8 per cent, fair, and below that figure, low grade. Steady mill feed averaging upward of 1.0 per cent WO3 is exceptional. Inasmuch as buying specifications demand a 60 per cent WO3 content, the mineral content of the ores as mined must be concentrated to at least that degree. A few companies have constructed chemical plants for the treatment of their complex concentrates and low-grade flotation product, but the smaller operator must rely on table concentration, borrowing the tools and to a large extent the methods of his predecessors in the gold, silver, lead and zinc mills. Whether these are the best tools and methods that can be devised is an open question. Except in rare instances, table concentration, however carefully conducted, does not yield a satisfactory final recovery of the mineral content in headings as indicated by chemical determinations of tungstic oxide content. A saving of 6o to 65 per cent is considered fair, and an average 80 per cent recovery, exceptional. Each scheelite ore body is a separate problem. Details of handling that give best results in one case may not be successfully operative at a property on the same contact zone and but a short distance removed. Supplementary treatment of tailings by flotation may be successful in producing a low-grade concentrate of around 15 per cent W03, which is adapted to further treatment chemically at a given property and entirely unsuccessful at another. This problem constitutes another of the unanswered questions. The following paragraphs relate solely to the beneficiation of scheelite ores by table concentration and supplementary methods.

Jan 1, 1942

In March 1962, over three months ahead of schedule, production began from the Ventersdorp Contact Reef of the Western Deep Levels Ltd. mine on the West Witwatersrand. Few mines have captured the interest of mining men and the public as has Western Deep Levels. It has presented the gold mining industry with a challenge which involved the opening of an ultradeep mine with the attendant problems of exceptionally heavy capital commitments ($77 million to start of production), high rock temperatures and pressures at great depths, cementation and pumping in an area notorious for the volume of subsurface water, and the necessity for entirely new thinking and the application of new ideas. HISTORY Not all the problems facing Western Deep Levels were, however, new. Situated 43 miles from Johannesburg, just off the main road to Potchefstroom, Western Deep Levels was the sixth company to undertake mining operations on what is known as the West Wits line and it could draw on the wealth of experience gained by other pioneer mines in the area.

Jan 12, 1962

By John M. Logan, John Handin

Quasi-dynamic triaxial compression tests have been done for the first time at confining pressures to 7 kb. The intermediate strain-rate apparatus employs a gas loading cylinder which allows axial strain rates up to 102/sec on a sample 2 cm in diameter and 4 cm long. Samples can be deformed at confining pressures to 7 kb. Strain gages bonded to the loading piston and to the jacketed specimen allow internal measurements of load and sample strains respectively. Westerly granite has been deformed at confining pressures to 7 kb, room temperature, and axial strain rates of 10-2 to 1/sec. An increase of ultimate strength with confining pressure was found as expected. The ultimate strength was also found to vary directly with increasing strain rate; the rate of rise increases with confining pressure. Brittle deformation has dominated the sample behavior. Solenhofen limestone has been deformed at confining pressures to 3 kb, room temperature, and axial strain rates of 10- to 10/sec. The brittle-ductile transition was found to take place at about 1.5 kb confining pressure at a strain rate of 10/sec.

Jan 1, 1971

By W. Rostoker, S. A. Spachner

FOLLOWING the discovery of the w transition phase in certain titanium-chromium alloys by Frost, Parris, Doig, and Schwartz, much interest has centered on the alloys in which this phase is found and its mode of precipitation. The w phase has been found in alloys of Ti-Cr, Ti-Fe, Ti-Mn, Ti-MO,2 and Ti-v.3 The temperature-time-transformation characteristics have, as yet, not been determined for most of these. In this study, such transformation characteristics have been investigated for two heat-treatable titanium alloys known to exhibit transition phase phenomena. The alloys chosen, Ti-8Cr and Ti-13M0, are representative of two classes of binary equilibrium systems. In the

Jan 1, 1959

By Jan M. Mutmansky

Main purpose of the research described is to apply the method of computer simulation to the process of tunneling by rapid excavation methods. Primary attention was focused on the materials handling subsystem because of its potential for improvement from a systems standpoint. A description is given of the computer model and a summary of some applications of the model for improving the rapid excavation process is included.

Jan 1, 1975

The ten-year "supply-demand relationship" tables in this chapter for various mineral and metal commodities have been adapted from Minerals in the U.S. Economy, compiled by the Bureau of Mines, U.S. Department of the Interior, published in 1975. Acknowledgment is made to the Bureau of Mines for compilation of the tables. [ ]

Jan 1, 1976

By Earle E. Schumacher

THE elements silicon and germanium are not metals within the usual, intuitive association of the word, nor are they so within a stricter definition based on the electronic binding. Two properties associated with metals are plasticity and high electrical conductivity. These elements crystallize in the diamond cubic structure, an arrangement apparently not very favorable to slip, and are therefore brittle rather than ductile. Their electrical conductivity is not like that of metals the atoms are locked together by the covalent bond, which in pure and perfectly arranged material leaves but few electrons free to act as electrical carriers.† In further contrast to metals, their electrical conductivity can be greatly increased by raising the temperature. Yet silicon and germanium are not ideally nonmetallic. They are hard, solid, and possess a metallic luster. They exhibit that peculiar brand of electrical conductivity conveniently termed "semi- conduction," wherein, as shall be seen, lies much of their importance. Both, but silicon in particular, are important components in real metallic alloys and the methods of their reduction and preparation lie clearly in the province of the metallurgist. From their duality of physical and chemical properties, silicon and germanium, along with such elements as boron, diamond, gray tin, selenium, antimony, and arsenic, are considered semimetals or metalloids. Because of their importance to metallurgy and the im-

Jan 1, 1953

By Fred B. Brost

In 1976, a decision was made to install a conveying system to transport ore 10.3 km (6.4 miles) from the new Eisenhower mine to Twin Buttes. The system, supplied and installed by Cable Belt Ltd., of England, represents a radical departure from conventional conveyor systems. The driving tension is applied through two endless wire ropes while the belt acts only as the carrying medium. Features of the system are a single 2240-kW (3000-hp) drive and a 60° angle bend. Construction was completed in two years and full production was attained alter several mouths operation.

Jan 12, 1979

By V. C. Allison

Large-scale testing of the explosibility of coal dust as conducted by the Bureau of Mines in its Experimental Mine involves a large initial investment, and a high charge for maintenance and conduct of the test; in addition the work is necessarily slow because of the time required for the preparntion of the tests and the cleaning and repairing of the mine after each test. These tests have been made along practical mining lines that admit of a range of mixtures of dust varying from 5 to 10 per cent. and with gas as low as 0.5 per cent. increments. Because of the time and expense involved, efforts have been made to devise a type of gallery for laboratory use in which the results obtained in the Experimental Mine may be correlated as an aid in a study of dusts, the explosibility of which might be approximately determined quickly and at a minimum of expense. The explosibility of coal dust has been studied by a number of European investors, using small laboratory devices; among these may be mentioned the experiments conducted by Galloway, Vital, Hall and Clark, Abel, Mallard and Chatelier, Thorpe, Bedson and Widdas, Engler, Holwartz and Meyer, and Taffanel, results of whose experiments have becn reviewed by the Bureau of Mines.' The Bureau has conducted many tests with the Frazer-Cle1ncnt5 apparattus, which gives the pressures set up when the dust cloud within is ignited with a platinum coil or tube, heated to different temperatures, but for these tests the sample must be especially prepared as to size (200 mesh) and must be dry. Need for a Dust-testing Apparatus An attempt has been made to design an apparatus that may be used for checking and correlating the expcrimental tests. The first design was a wooden gallery, 8 by 10 in., inside cross section, and 12 ft. long, and having a number of strips along each side for creation of turbulence. The wooden gallery did not get beyond its period of calibration; it mas difficult to make the gallery sufficiently tight, for it was necessary that the top be removable in order that the gallery could be cleaned. In the use of the wooden gallery, however, sufficient operating data were obtained to be a guide in the design of a steel gallery having a circular cross-section. One of the features was a flap valve, at the closed end of the gallery, that would open inwardly thus preventing a reduced pressure within, caused by the cooling of the gases of combustion, and the explosions propagated much better than when the valve was not used; another feature was the determining of the best method for getting a cloud of dust simultaneously in all parts of the gallery, which was accomplished by the use of the concussion wave of a small quantity of powder or by the use of compressed air.

Jan 1, 1927

By John L. Burnett

Manufacture of lightweight concrete aggregate from common shale is one of the most rapidly growing industries in the field of nonmetallic or industrial minerals. Although expanded shale" has been in use since it was developed by Stephen J. Hayde in 1917, it was not until after World War II that it became a substantial competitor with other aggregates. There are some 70 plants now producing this aggregate in the United States, approximately half of them in states west of the Mississippi River. Expanding plants throughout the U. S. are grouped around major urban centers such as Los Angeles, New York, Chicago, and Denver. Concrete made with expanded shale aggregate combines the desirable features of low weight with relatively high strength, making it especially useful in concrete block, in structural concrete for multi-story buildings and in a variety of specialized concrete products such as prestressed panels and beams, and storage tanks. As the cost of construction continues to rise, lightweight concrete will probably be used in increasing quantities because of its low cost relative to the more traditional construction materials such as wood, brick and steel

Jan 1, 1964

By V. E. McKelvey

The Phosphoria formation of the northwestern states presents a stimulating challenge to workers in every field of mineral technology. In addition to its large reserves of phosphate, the formation has been found to contain important amounts of fluorine and several metals, such as vanadium, nickel, and molybdenum. Because these minor metals in the Phosphoria do not have their usual glitter, concentrations of them are not easily discovered nor appraised. Like the phosphate itself, production of these metals very likely can be achieved only through use of costly chemical methods, for their mineralogy precludes treatment by the usual methods. In addition, in much of the area the containing rocks lie in complexly folded and faulted structures, which complicate mining and increase its cost. Yet the chain of research necessary to establish what elements are present; their geographic and stratigraphic distribution and reserves; the most suitable methods for recovering them; the combination of beds which, when ruined and processed, will yield the greatest recovery of the most valuable elements; and the methods most adaptable to their profitable extraction may well lead to the development of an important mineral industry and may make possible a significaut reduction in the cost of fertilizer this in itself would be an achievement of momentous importance—and at the same time make the nation more self-sustaining in critical materials. Although this research has great

Jan 1, 1950

By Frank L. Antisell

Certain physical and chemical properties of copper are so intimately related that a change in variation of the physical properties indicates a certain chemical change. The standard specifications of copper of the American Society for Testing Materials are based upon physical characteristics with one exception, namely, the copper contents. The physical standard includes electrical properties, defects in the "set or casting," variation in dimensions, weight, etc. Paragraph 4 of the specifications states, " Wire bars, cakes, slabs and billets shall be substantially free from shrink holes, cold sets, pits, sloppy edges, concave tops, and similar defects in set or casting." Shrink holes and concave tops indicate both physical and metallurgical defects; cold sets, sloppy edges, etc., indicate physical defects only; small pit holes may be indicative of either or both physical and metallurgical defects, depending on conditions under which they originated. To the refiner, a copper casting, no matter how made, is known as a "shape," irrespective of whether it is wire bar, ingot, cake, slab, billet, etc. As practically all shapes are cast in an open mold, that is a mold without cope, the surface of the shape cools in contact with the atmosphere and has a coating of oxide. Certain phenomena of the surface indicate the adaptability of the metal for forging or rolling. The writer believes that it is much simpler to produce shapes that are metallurgically correct than those that are mechanically satisfactory. When copper is to be rolled into thin sheets or drawn into very fine wire, the slightest physical defect becomes evident. It is, therefore, of the utmost importance to consider every characteristic of the shape and ascertain the physical and chemical relationship. Pitch and Set.—The appearance of the surface of the copper when cooled is considered as to its "pitch," or the general contour of the surface of the shape (which may vary from a concave to a convex); and the '" set,"' or the detail appearance of the surface of the shape (the wave-like structure). When the shape presents a concave surface, it is known as "low pitch;" a convex surface is known as "high pitch" or "tough pitch;" and a level surface is called "flat pitch." The set of the copper is, in a very large measure, directly related to the pitch; and so intimately are

Jan 1, 1921